carl9170 firmware: replace ---help--- with help syntax

upstream kconfig is replacing the ---help--- command syntax with help.

Signed-off-by: Christian Lamparter <chunkeey@gmail.com>

diff --git a/carlfw/Kconfig b/carlfw/Kconfig
index 46eb1bb87399f5ba4250d43d71a5d05daa9412fe..455c793536a326f4746b3fc94a9f2f6b33763123 100644 (file)
--- a/carlfw/Kconfig
+++ b/carlfw/Kconfig
@@ -34,7 +34,7 @@ config CARL9170FW_RX_FRAME_LEN
 config CARL9170FW_GPIO_INTERRUPT
        def_bool y
        prompt "GPIO Software Interrupt"
-       ---help---
+       help
         When this option is enabled, the firmware will poll the GPIO
         registers and reports to the driver whenever the GPIO state
         has changed from a previous state.
@@ -45,7 +45,7 @@ config CARL9170FW_GPIO_INTERRUPT
 config CARL9170FW_SECURITY_ENGINE
        def_bool y
        prompt "Support Hardware Crypto Engine"
-       ---help---
+       help
         This options controls if the firmware will allow the driver
         to program the security engine / CAM through a firmware
         interface.
@@ -56,7 +56,7 @@ config CARL9170FW_SECURITY_ENGINE
 config CARL9170FW_RADIO_FUNCTIONS
        def_bool y
        prompt "Enable Firmware-supported Radio/RF functions"
-       ---help---
+       help
         Some PHY/RF functions (e.g.: AGC and Noise calibration) need
         to be done in the firmware.
 
@@ -73,7 +73,7 @@ config CARL9170FW_PRINTF
        def_bool y
        prompt "Advanced printf"
        depends on CARL9170FW_DEBUG_UART || CARL9170FW_DEBUG_USB
-       ---help---
+       help
         Advanced printf (very useful for debugging purposes)
         The formats supported by this implementation are:
                'd' 'u' 'c' 's' 'x' 'X' 'p'.
@@ -89,7 +89,7 @@ config CARL9170FW_WOL_OPTION
        def_bool n
        prompt "Wakeup on WLAN"
        depends on CARL9170FW_EXPERIMENTAL
-       ---help---
+       help
         With this option enabled, the firmware can wake-up
         suspended hosts... As long as they fully support
         USB remote wakeup.
@@ -103,7 +103,7 @@ config CARL9170FW_WOL_NL80211_TRIGGERS
        prompt "Standard NL80211 wakeup triggers"
        depends on CARL9170FW_WOL_OPTION
        select CARL9170FW_WOL
-       ---help---
+       help
         Available triggers:
          * Magic Packet(tm) pattern
          * disconnect event
@@ -113,7 +113,7 @@ config CARL9170FW_WOL_PROBE_REQUEST
        prompt "Probe Request"
        depends on CARL9170FW_WOL_OPTION
        select CARL9170FW_WOL
-       ---help---
+       help
         Scan probe requests for a given SSID.
 
 config CARL9170FW_WOL_PROBE_REQUEST_SSID
@@ -142,7 +142,7 @@ config CARL9170FW_80MHZ_CLOCK
        def_bool n
        prompt "Allow 80/88MHz clock for HT40"
        depends on CARL9170FW_EXPERIMENTAL
-       ---help---
+       help
         The SoC can run up to 80/88MHz in HT40 mode. This improves
         throughput and timing accuracy over the 40/44MHz clock.
         However some devices don't have heat shields and they with
@@ -161,7 +161,7 @@ config CARL9170FW_DEBUG_LED_HEARTBEAT
        def_bool n
        prompt "LED Heartbeat"
        depends on CARL9170FW_BROKEN_FEATURES
-       ---help---
+       help
         This option conflicts with the application's LED code.
         Also, it assumes that you have two LEDs, which is not
         necessarily true.
@@ -170,7 +170,7 @@ config CARL9170FW_DEBUG_UART
        def_bool n
        prompt "Pass debug messages through Highspeed UART"
        depends on CARL9170FW_BROKEN_FEATURES
-       ---help---
+       help
         This option allows the firmware to send BUG/ERR/INFO/DBG and
         hexdumps through the UART _as well_. However, first: you must
         connect a working logger.
@@ -201,7 +201,7 @@ config CARL9170FW_USB_MODESWITCH
        def_bool n
        prompt "USB 1.1 / 2.0 switching support"
        depends on CARL9170FW_BROKEN_FEATURES && CARL9170FW_USB_STANDARD_CMDS
-       ---help---
+       help
         Mostly implemented, but untested and some serious
         doubts remain.
 
@@ -214,7 +214,7 @@ menu "Build Options"
 config CARL9170FW_AGGRESSIVE_CFLAGS
        def_bool y
        prompt "Enable aggressive size optimization"
-       ---help---
+       help
         This option adds several more optimization compiler flags,
         which can greatly reduce the firmware size... at the expense
         of machine-code readability.

diff --git a/carlfw/usb/Kconfig b/carlfw/usb/Kconfig
index dc70776d6979764f1afd27cf3932ffcbdeb095e1..0cea6c264359ab06a2e4ef84f7a22c3542cfb909 100644 (file)
--- a/carlfw/usb/Kconfig
+++ b/carlfw/usb/Kconfig
@@ -3,7 +3,7 @@ menu "USB Firmware Configuration Settings"
 config CARL9170FW_USB_STANDARD_CMDS
        def_bool y
        prompt "Basic USB Interface"
-       ---help---
+       help
         Allows the device to be queried about Standard USB 2.0 Device
         Description Descriptors.
 
@@ -12,7 +12,7 @@ config CARL9170FW_USB_STANDARD_CMDS
 config CARL9170FW_USB_UP_STREAM
        def_bool y
        prompt "USB Upload Stream"
-       ---help---
+       help
         This features allows the USB silicon to combine small, single
         frames into bigger transfers. This can help to reduce
         some per-transfer overhead in the application.
@@ -26,7 +26,7 @@ config CARL9170FW_USB_DN_STREAM
 config CARL9170FW_DEBUG_USB
        def_bool y
        prompt "Pass debug messages through USB transport"
-       ---help---
+       help
         Report all firmware messages through the USB transport.
         But there is a catch: In case of a BUG, the USB transport
         needs to be functional, otherwise the application won't