From dc75d2a0268f21a44ddcc7546e5919e020a75bc1 Mon Sep 17 00:00:00 2001 From: Christian Lamparter Date: Fri, 5 Feb 2021 12:03:09 +0100 Subject: [PATCH] carl9170 firmware: replace ---help--- with help syntax upstream kconfig is replacing the ---help--- command syntax with help. Signed-off-by: Christian Lamparter --- carlfw/Kconfig | 24 ++++++++++++------------ carlfw/usb/Kconfig | 6 +++--- 2 files changed, 15 insertions(+), 15 deletions(-) diff --git a/carlfw/Kconfig b/carlfw/Kconfig index 46eb1bb..455c793 100644 --- a/carlfw/Kconfig +++ b/carlfw/Kconfig @@ -34,7 +34,7 @@ config CARL9170FW_RX_FRAME_LEN config CARL9170FW_GPIO_INTERRUPT def_bool y prompt "GPIO Software Interrupt" - ---help--- + help When this option is enabled, the firmware will poll the GPIO registers and reports to the driver whenever the GPIO state has changed from a previous state. @@ -45,7 +45,7 @@ config CARL9170FW_GPIO_INTERRUPT config CARL9170FW_SECURITY_ENGINE def_bool y prompt "Support Hardware Crypto Engine" - ---help--- + help This options controls if the firmware will allow the driver to program the security engine / CAM through a firmware interface. @@ -56,7 +56,7 @@ config CARL9170FW_SECURITY_ENGINE config CARL9170FW_RADIO_FUNCTIONS def_bool y prompt "Enable Firmware-supported Radio/RF functions" - ---help--- + help Some PHY/RF functions (e.g.: AGC and Noise calibration) need to be done in the firmware. @@ -73,7 +73,7 @@ config CARL9170FW_PRINTF def_bool y prompt "Advanced printf" depends on CARL9170FW_DEBUG_UART || CARL9170FW_DEBUG_USB - ---help--- + help Advanced printf (very useful for debugging purposes) The formats supported by this implementation are: 'd' 'u' 'c' 's' 'x' 'X' 'p'. @@ -89,7 +89,7 @@ config CARL9170FW_WOL_OPTION def_bool n prompt "Wakeup on WLAN" depends on CARL9170FW_EXPERIMENTAL - ---help--- + help With this option enabled, the firmware can wake-up suspended hosts... As long as they fully support USB remote wakeup. @@ -103,7 +103,7 @@ config CARL9170FW_WOL_NL80211_TRIGGERS prompt "Standard NL80211 wakeup triggers" depends on CARL9170FW_WOL_OPTION select CARL9170FW_WOL - ---help--- + help Available triggers: * Magic Packet(tm) pattern * disconnect event @@ -113,7 +113,7 @@ config CARL9170FW_WOL_PROBE_REQUEST prompt "Probe Request" depends on CARL9170FW_WOL_OPTION select CARL9170FW_WOL - ---help--- + help Scan probe requests for a given SSID. config CARL9170FW_WOL_PROBE_REQUEST_SSID @@ -142,7 +142,7 @@ config CARL9170FW_80MHZ_CLOCK def_bool n prompt "Allow 80/88MHz clock for HT40" depends on CARL9170FW_EXPERIMENTAL - ---help--- + help The SoC can run up to 80/88MHz in HT40 mode. This improves throughput and timing accuracy over the 40/44MHz clock. However some devices don't have heat shields and they with @@ -161,7 +161,7 @@ config CARL9170FW_DEBUG_LED_HEARTBEAT def_bool n prompt "LED Heartbeat" depends on CARL9170FW_BROKEN_FEATURES - ---help--- + help This option conflicts with the application's LED code. Also, it assumes that you have two LEDs, which is not necessarily true. @@ -170,7 +170,7 @@ config CARL9170FW_DEBUG_UART def_bool n prompt "Pass debug messages through Highspeed UART" depends on CARL9170FW_BROKEN_FEATURES - ---help--- + help This option allows the firmware to send BUG/ERR/INFO/DBG and hexdumps through the UART _as well_. However, first: you must connect a working logger. @@ -201,7 +201,7 @@ config CARL9170FW_USB_MODESWITCH def_bool n prompt "USB 1.1 / 2.0 switching support" depends on CARL9170FW_BROKEN_FEATURES && CARL9170FW_USB_STANDARD_CMDS - ---help--- + help Mostly implemented, but untested and some serious doubts remain. @@ -214,7 +214,7 @@ menu "Build Options" config CARL9170FW_AGGRESSIVE_CFLAGS def_bool y prompt "Enable aggressive size optimization" - ---help--- + help This option adds several more optimization compiler flags, which can greatly reduce the firmware size... at the expense of machine-code readability. diff --git a/carlfw/usb/Kconfig b/carlfw/usb/Kconfig index dc70776..0cea6c2 100644 --- a/carlfw/usb/Kconfig +++ b/carlfw/usb/Kconfig @@ -3,7 +3,7 @@ menu "USB Firmware Configuration Settings" config CARL9170FW_USB_STANDARD_CMDS def_bool y prompt "Basic USB Interface" - ---help--- + help Allows the device to be queried about Standard USB 2.0 Device Description Descriptors. @@ -12,7 +12,7 @@ config CARL9170FW_USB_STANDARD_CMDS config CARL9170FW_USB_UP_STREAM def_bool y prompt "USB Upload Stream" - ---help--- + help This features allows the USB silicon to combine small, single frames into bigger transfers. This can help to reduce some per-transfer overhead in the application. @@ -26,7 +26,7 @@ config CARL9170FW_USB_DN_STREAM config CARL9170FW_DEBUG_USB def_bool y prompt "Pass debug messages through USB transport" - ---help--- + help Report all firmware messages through the USB transport. But there is a catch: In case of a BUG, the USB transport needs to be functional, otherwise the application won't -- 2.31.1