+/* SPDX-License-Identifier: GPL-2.0 WITH Linux-syscall-note */
/*
* This file holds USB constants and structures that are needed for
* USB device APIs. These are used by the USB device model, which is
* This bit flag is used in endpoint descriptors' bEndpointAddress field.
* It's also one of three fields in control requests bRequestType.
*/
-#define USB_DIR_MASK 0x80
#define USB_DIR_OUT 0 /* to device */
#define USB_DIR_IN 0x80 /* to host */
+#define USB_DIR_MASK 0x80
/*
* USB types, the second of three bRequestType fields
#define USB_REQ_GET_INTERFACE 0x0A
#define USB_REQ_SET_INTERFACE 0x0B
#define USB_REQ_SYNCH_FRAME 0x0C
+#define USB_REQ_SET_SEL 0x30
+#define USB_REQ_SET_ISOCH_DELAY 0x31
#define USB_REQ_SET_ENCRYPTION 0x0D /* Wireless USB */
#define USB_REQ_GET_ENCRYPTION 0x0E
#define USB_REQ_LOOPBACK_DATA_READ 0x16
#define USB_REQ_SET_INTERFACE_DS 0x17
+/* specific requests for USB Power Delivery */
+#define USB_REQ_GET_PARTNER_PDO 20
+#define USB_REQ_GET_BATTERY_STATUS 21
+#define USB_REQ_SET_PDO 22
+#define USB_REQ_GET_VDM 23
+#define USB_REQ_SEND_VDM 24
+
/* The Link Power Management (LPM) ECN defines USB_REQ_TEST_AND_SET command,
* used by hubs to put ports into a new L1 suspend state, except that it
* forgot to define its number ...
#define USB_DEVICE_A_ALT_HNP_SUPPORT 5 /* (otg) other RH port does */
#define USB_DEVICE_DEBUG_MODE 6 /* (special devices only) */
+/*
+ * Test Mode Selectors
+ * See USB 2.0 spec Table 9-7
+ */
+#define USB_TEST_J 1
+#define USB_TEST_K 2
+#define USB_TEST_SE0_NAK 3
+#define USB_TEST_PACKET 4
+#define USB_TEST_FORCE_ENABLE 5
+
+/* Status Type */
+#define USB_STATUS_TYPE_STANDARD 0
+#define USB_STATUS_TYPE_PTM 1
+
+/*
+ * New Feature Selectors as added by USB 3.0
+ * See USB 3.0 spec Table 9-7
+ */
+#define USB_DEVICE_U1_ENABLE 48 /* dev may initiate U1 transition */
+#define USB_DEVICE_U2_ENABLE 49 /* dev may initiate U2 transition */
+#define USB_DEVICE_LTM_ENABLE 50 /* dev may send LTM */
+#define USB_INTRF_FUNC_SUSPEND 0 /* function suspend */
+
+#define USB_INTR_FUNC_SUSPEND_OPT_MASK 0xFF00
+/*
+ * Suspend Options, Table 9-8 USB 3.0 spec
+ */
+#define USB_INTRF_FUNC_SUSPEND_LP (1 << (8 + 0))
+#define USB_INTRF_FUNC_SUSPEND_RW (1 << (8 + 1))
+
+/*
+ * Interface status, Figure 9-5 USB 3.0 spec
+ */
+#define USB_INTRF_STAT_FUNC_RW_CAP 1
+#define USB_INTRF_STAT_FUNC_RW 2
+
#define USB_ENDPOINT_HALT 0 /* IN/OUT will STALL */
+/* Bit array elements as returned by the USB_REQ_GET_STATUS request. */
+#define USB_DEV_STAT_U1_ENABLED 2 /* transition into U1 state */
+#define USB_DEV_STAT_U2_ENABLED 3 /* transition into U2 state */
+#define USB_DEV_STAT_LTM_ENABLED 4 /* Latency tolerance messages */
+
+/*
+ * Feature selectors from Table 9-8 USB Power Delivery spec
+ */
+#define USB_DEVICE_BATTERY_WAKE_MASK 40
+#define USB_DEVICE_OS_IS_PD_AWARE 41
+#define USB_DEVICE_POLICY_MODE 42
+#define USB_PORT_PR_SWAP 43
+#define USB_PORT_GOTO_MIN 44
+#define USB_PORT_RETURN_POWER 45
+#define USB_PORT_ACCEPT_PD_REQUEST 46
+#define USB_PORT_REJECT_PD_REQUEST 47
+#define USB_PORT_PORT_PD_RESET 48
+#define USB_PORT_C_PORT_PD_CHANGE 49
+#define USB_PORT_CABLE_PD_RESET 50
+#define USB_DEVICE_CHARGING_POLICY 54
/**
* struct usb_ctrlrequest - SETUP data for a USB device control request
* through the Linux-USB APIs, they are not converted to cpu byte
* order; it is the responsibility of the client code to do this.
* The single exception is when device and configuration descriptors (but
- * not other descriptors) are read from usbfs (i.e. /proc/bus/usb/BBB/DDD);
+ * not other descriptors) are read from character devices
+ * (i.e. /dev/bus/usb/BBB/DDD);
* in this case the fields are converted to host endianness by the kernel.
*/
#define USB_DT_WIRE_ADAPTER 0x21
#define USB_DT_RPIPE 0x22
#define USB_DT_CS_RADIO_CONTROL 0x23
+/* From the T10 UAS specification */
+#define USB_DT_PIPE_USAGE 0x24
/* From the USB 3.0 spec */
#define USB_DT_SS_ENDPOINT_COMP 0x30
+/* From the USB 3.1 spec */
+#define USB_DT_SSP_ISOC_ENDPOINT_COMP 0x31
/* Conventional codes for class-specific descriptors. The convention is
* defined in the USB "Common Class" Spec (3.11). Individual class specs
#define USB_CLASS_CONTENT_SEC 0x0d /* content security */
#define USB_CLASS_VIDEO 0x0e
#define USB_CLASS_WIRELESS_CONTROLLER 0xe0
+#define USB_CLASS_PERSONAL_HEALTHCARE 0x0f
+#define USB_CLASS_AUDIO_VIDEO 0x10
+#define USB_CLASS_BILLBOARD 0x11
+#define USB_CLASS_USB_TYPE_C_BRIDGE 0x12
#define USB_CLASS_MISC 0xef
#define USB_CLASS_APP_SPEC 0xfe
#define USB_CLASS_VENDOR_SPEC 0xff
/*-------------------------------------------------------------------------*/
+/* USB String descriptors can contain at most 126 characters. */
+#define USB_MAX_STRING_LEN 126
+
/* USB_DT_STRING: String descriptor */
struct usb_string_descriptor {
__u8 bLength;
#define USB_ENDPOINT_NUMBER_MASK 0x0f /* in bEndpointAddress */
#define USB_ENDPOINT_DIR_MASK 0x80
-#define USB_ENDPOINT_SYNCTYPE 0x0c
-#define USB_ENDPOINT_SYNC_NONE (0 << 2)
-#define USB_ENDPOINT_SYNC_ASYNC (1 << 2)
-#define USB_ENDPOINT_SYNC_ADAPTIVE (2 << 2)
-#define USB_ENDPOINT_SYNC_SYNC (3 << 2)
-
#define USB_ENDPOINT_XFERTYPE_MASK 0x03 /* in bmAttributes */
#define USB_ENDPOINT_XFER_CONTROL 0
#define USB_ENDPOINT_XFER_ISOC 1
#define USB_ENDPOINT_XFER_INT 3
#define USB_ENDPOINT_MAX_ADJUSTABLE 0x80
+#define USB_ENDPOINT_MAXP_MASK 0x07ff
+#define USB_EP_MAXP_MULT_SHIFT 11
+#define USB_EP_MAXP_MULT_MASK (3 << USB_EP_MAXP_MULT_SHIFT)
+#define USB_EP_MAXP_MULT(m) \
+ (((m) & USB_EP_MAXP_MULT_MASK) >> USB_EP_MAXP_MULT_SHIFT)
+
+/* The USB 3.0 spec redefines bits 5:4 of bmAttributes as interrupt ep type. */
+#define USB_ENDPOINT_INTRTYPE 0x30
+#define USB_ENDPOINT_INTR_PERIODIC (0 << 4)
+#define USB_ENDPOINT_INTR_NOTIFICATION (1 << 4)
+
+#define USB_ENDPOINT_SYNCTYPE 0x0c
+#define USB_ENDPOINT_SYNC_NONE (0 << 2)
+#define USB_ENDPOINT_SYNC_ASYNC (1 << 2)
+#define USB_ENDPOINT_SYNC_ADAPTIVE (2 << 2)
+#define USB_ENDPOINT_SYNC_SYNC (3 << 2)
+
+#define USB_ENDPOINT_USAGE_MASK 0x30
+#define USB_ENDPOINT_USAGE_DATA 0x00
+#define USB_ENDPOINT_USAGE_FEEDBACK 0x10
+#define USB_ENDPOINT_USAGE_IMPLICIT_FB 0x20 /* Implicit feedback Data endpoint */
+
/*-------------------------------------------------------------------------*/
/**
static inline int usb_endpoint_xfer_isoc(
const struct usb_endpoint_descriptor *epd)
{
- return (epd->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) ==
- USB_ENDPOINT_XFER_ISOC;
+ return ((epd->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK) ==
+ USB_ENDPOINT_XFER_ISOC);
}
/**
return usb_endpoint_xfer_isoc(epd) && usb_endpoint_dir_out(epd);
}
+/**
+ * usb_endpoint_maxp - get endpoint's max packet size
+ * @epd: endpoint to be checked
+ *
+ * Returns @epd's max packet bits [10:0]
+ */
+static inline int usb_endpoint_maxp(const struct usb_endpoint_descriptor *epd)
+{
+ return le16_to_cpu(epd->wMaxPacketSize) & USB_ENDPOINT_MAXP_MASK;
+}
+
+/**
+ * usb_endpoint_maxp_mult - get endpoint's transactional opportunities
+ * @epd: endpoint to be checked
+ *
+ * Return @epd's wMaxPacketSize[12:11] + 1
+ */
+static inline int
+usb_endpoint_maxp_mult(const struct usb_endpoint_descriptor *epd)
+{
+ int maxp = le16_to_cpu(epd->wMaxPacketSize);
+
+ return USB_EP_MAXP_MULT(maxp) + 1;
+}
+
+static inline int usb_endpoint_interrupt_type(
+ const struct usb_endpoint_descriptor *epd)
+{
+ return epd->bmAttributes & USB_ENDPOINT_INTRTYPE;
+}
+
+/*-------------------------------------------------------------------------*/
+
+/* USB_DT_SSP_ISOC_ENDPOINT_COMP: SuperSpeedPlus Isochronous Endpoint Companion
+ * descriptor
+ */
+struct usb_ssp_isoc_ep_comp_descriptor {
+ __u8 bLength;
+ __u8 bDescriptorType;
+ __le16 wReseved;
+ __le32 dwBytesPerInterval;
+} __attribute__ ((packed));
+
+#define USB_DT_SSP_ISOC_EP_COMP_SIZE 8
+
/*-------------------------------------------------------------------------*/
/* USB_DT_SS_ENDPOINT_COMP: SuperSpeed Endpoint Companion descriptor */
#define USB_DT_SS_EP_COMP_SIZE 6
+/* Bits 4:0 of bmAttributes if this is a bulk endpoint */
+static inline int
+usb_ss_max_streams(const struct usb_ss_ep_comp_descriptor *comp)
+{
+ int max_streams;
+
+ if (!comp)
+ return 0;
+
+ max_streams = comp->bmAttributes & 0x1f;
+
+ if (!max_streams)
+ return 0;
+
+ max_streams = 1 << max_streams;
+
+ return max_streams;
+}
+
+/* Bits 1:0 of bmAttributes if this is an isoc endpoint */
+#define USB_SS_MULT(p) (1 + ((p) & 0x3))
+/* Bit 7 of bmAttributes if a SSP isoc endpoint companion descriptor exists */
+#define USB_SS_SSP_ISOC_COMP(p) ((p) & (1 << 7))
+
/*-------------------------------------------------------------------------*/
/* USB_DT_DEVICE_QUALIFIER: Device Qualifier descriptor */
__u8 bmAttributes; /* support for HNP, SRP, etc */
} __attribute__ ((packed));
+/* USB_DT_OTG (from OTG 2.0 supplement) */
+struct usb_otg20_descriptor {
+ __u8 bLength;
+ __u8 bDescriptorType;
+
+ __u8 bmAttributes; /* support for HNP, SRP and ADP, etc */
+ __le16 bcdOTG; /* OTG and EH supplement release number
+ * in binary-coded decimal(i.e. 2.0 is 0200H)
+ */
+} __attribute__ ((packed));
+
/* from usb_otg_descriptor.bmAttributes */
#define USB_OTG_SRP (1 << 0)
#define USB_OTG_HNP (1 << 1) /* swap host/device roles */
+#define USB_OTG_ADP (1 << 2) /* support ADP */
+#define OTG_STS_SELECTOR 0xF000 /* OTG status selector */
/*-------------------------------------------------------------------------*/
/* USB_DT_DEBUG: for special highspeed devices, replacing serial console */
__u8 iFunction;
} __attribute__ ((packed));
+#define USB_DT_INTERFACE_ASSOCIATION_SIZE 8
/*-------------------------------------------------------------------------*/
__u8 bNumDeviceCaps;
} __attribute__((packed));
+#define USB_DT_BOS_SIZE 5
/*-------------------------------------------------------------------------*/
/* USB_DT_DEVICE_CAPABILITY: grouped with BOS */
__u8 bReserved;
} __attribute__((packed));
+#define USB_DT_USB_WIRELESS_CAP_SIZE 11
+
+/* USB 2.0 Extension descriptor */
#define USB_CAP_TYPE_EXT 2
struct usb_ext_cap_descriptor { /* Link Power Management */
__u8 bLength;
__u8 bDescriptorType;
__u8 bDevCapabilityType;
- __u8 bmAttributes;
+ __le32 bmAttributes;
#define USB_LPM_SUPPORT (1 << 1) /* supports LPM */
+#define USB_BESL_SUPPORT (1 << 2) /* supports BESL */
+#define USB_BESL_BASELINE_VALID (1 << 3) /* Baseline BESL valid*/
+#define USB_BESL_DEEP_VALID (1 << 4) /* Deep BESL valid */
+#define USB_SET_BESL_BASELINE(p) (((p) & 0xf) << 8)
+#define USB_SET_BESL_DEEP(p) (((p) & 0xf) << 12)
+#define USB_GET_BESL_BASELINE(p) (((p) & (0xf << 8)) >> 8)
+#define USB_GET_BESL_DEEP(p) (((p) & (0xf << 12)) >> 12)
+} __attribute__((packed));
+
+#define USB_DT_USB_EXT_CAP_SIZE 7
+
+/*
+ * SuperSpeed USB Capability descriptor: Defines the set of SuperSpeed USB
+ * specific device level capabilities
+ */
+#define USB_SS_CAP_TYPE 3
+struct usb_ss_cap_descriptor { /* Link Power Management */
+ __u8 bLength;
+ __u8 bDescriptorType;
+ __u8 bDevCapabilityType;
+ __u8 bmAttributes;
+#define USB_LTM_SUPPORT (1 << 1) /* supports LTM */
+ __le16 wSpeedSupported;
+#define USB_LOW_SPEED_OPERATION (1) /* Low speed operation */
+#define USB_FULL_SPEED_OPERATION (1 << 1) /* Full speed operation */
+#define USB_HIGH_SPEED_OPERATION (1 << 2) /* High speed operation */
+#define USB_5GBPS_OPERATION (1 << 3) /* Operation at 5Gbps */
+ __u8 bFunctionalitySupport;
+ __u8 bU1devExitLat;
+ __le16 bU2DevExitLat;
+} __attribute__((packed));
+
+#define USB_DT_USB_SS_CAP_SIZE 10
+
+/*
+ * Container ID Capability descriptor: Defines the instance unique ID used to
+ * identify the instance across all operating modes
+ */
+#define CONTAINER_ID_TYPE 4
+struct usb_ss_container_id_descriptor {
+ __u8 bLength;
+ __u8 bDescriptorType;
+ __u8 bDevCapabilityType;
+ __u8 bReserved;
+ __u8 ContainerID[16]; /* 128-bit number */
} __attribute__((packed));
+#define USB_DT_USB_SS_CONTN_ID_SIZE 20
+
+/*
+ * SuperSpeed Plus USB Capability descriptor: Defines the set of
+ * SuperSpeed Plus USB specific device level capabilities
+ */
+#define USB_SSP_CAP_TYPE 0xa
+struct usb_ssp_cap_descriptor {
+ __u8 bLength;
+ __u8 bDescriptorType;
+ __u8 bDevCapabilityType;
+ __u8 bReserved;
+ __le32 bmAttributes;
+#define USB_SSP_SUBLINK_SPEED_ATTRIBS (0x1f << 0) /* sublink speed entries */
+#define USB_SSP_SUBLINK_SPEED_IDS (0xf << 5) /* speed ID entries */
+ __le16 wFunctionalitySupport;
+#define USB_SSP_MIN_SUBLINK_SPEED_ATTRIBUTE_ID (0xf)
+#define USB_SSP_MIN_RX_LANE_COUNT (0xf << 8)
+#define USB_SSP_MIN_TX_LANE_COUNT (0xf << 12)
+ __le16 wReserved;
+ __le32 bmSublinkSpeedAttr[1]; /* list of sublink speed attrib entries */
+#define USB_SSP_SUBLINK_SPEED_SSID (0xf) /* sublink speed ID */
+#define USB_SSP_SUBLINK_SPEED_LSE (0x3 << 4) /* Lanespeed exponent */
+#define USB_SSP_SUBLINK_SPEED_ST (0x3 << 6) /* Sublink type */
+#define USB_SSP_SUBLINK_SPEED_RSVD (0x3f << 8) /* Reserved */
+#define USB_SSP_SUBLINK_SPEED_LP (0x3 << 14) /* Link protocol */
+#define USB_SSP_SUBLINK_SPEED_LSM (0xff << 16) /* Lanespeed mantissa */
+} __attribute__((packed));
+
+/*
+ * USB Power Delivery Capability Descriptor:
+ * Defines capabilities for PD
+ */
+/* Defines the various PD Capabilities of this device */
+#define USB_PD_POWER_DELIVERY_CAPABILITY 0x06
+/* Provides information on each battery supported by the device */
+#define USB_PD_BATTERY_INFO_CAPABILITY 0x07
+/* The Consumer characteristics of a Port on the device */
+#define USB_PD_PD_CONSUMER_PORT_CAPABILITY 0x08
+/* The provider characteristics of a Port on the device */
+#define USB_PD_PD_PROVIDER_PORT_CAPABILITY 0x09
+
+struct usb_pd_cap_descriptor {
+ __u8 bLength;
+ __u8 bDescriptorType;
+ __u8 bDevCapabilityType; /* set to USB_PD_POWER_DELIVERY_CAPABILITY */
+ __u8 bReserved;
+ __le32 bmAttributes;
+#define USB_PD_CAP_BATTERY_CHARGING (1 << 1) /* supports Battery Charging specification */
+#define USB_PD_CAP_USB_PD (1 << 2) /* supports USB Power Delivery specification */
+#define USB_PD_CAP_PROVIDER (1 << 3) /* can provide power */
+#define USB_PD_CAP_CONSUMER (1 << 4) /* can consume power */
+#define USB_PD_CAP_CHARGING_POLICY (1 << 5) /* supports CHARGING_POLICY feature */
+#define USB_PD_CAP_TYPE_C_CURRENT (1 << 6) /* supports power capabilities defined in the USB Type-C Specification */
+
+#define USB_PD_CAP_PWR_AC (1 << 8)
+#define USB_PD_CAP_PWR_BAT (1 << 9)
+#define USB_PD_CAP_PWR_USE_V_BUS (1 << 14)
+
+ __le16 bmProviderPorts; /* Bit zero refers to the UFP of the device */
+ __le16 bmConsumerPorts;
+ __le16 bcdBCVersion;
+ __le16 bcdPDVersion;
+ __le16 bcdUSBTypeCVersion;
+} __attribute__((packed));
+
+struct usb_pd_cap_battery_info_descriptor {
+ __u8 bLength;
+ __u8 bDescriptorType;
+ __u8 bDevCapabilityType;
+ /* Index of string descriptor shall contain the user friendly name for this battery */
+ __u8 iBattery;
+ /* Index of string descriptor shall contain the Serial Number String for this battery */
+ __u8 iSerial;
+ __u8 iManufacturer;
+ __u8 bBatteryId; /* uniquely identifies this battery in status Messages */
+ __u8 bReserved;
+ /*
+ * Shall contain the Battery Charge value above which this
+ * battery is considered to be fully charged but not necessarily
+ * “topped off.”
+ */
+ __le32 dwChargedThreshold; /* in mWh */
+ /*
+ * Shall contain the minimum charge level of this battery such
+ * that above this threshold, a device can be assured of being
+ * able to power up successfully (see Battery Charging 1.2).
+ */
+ __le32 dwWeakThreshold; /* in mWh */
+ __le32 dwBatteryDesignCapacity; /* in mWh */
+ __le32 dwBatteryLastFullchargeCapacity; /* in mWh */
+} __attribute__((packed));
+
+struct usb_pd_cap_consumer_port_descriptor {
+ __u8 bLength;
+ __u8 bDescriptorType;
+ __u8 bDevCapabilityType;
+ __u8 bReserved;
+ __u8 bmCapabilities;
+/* port will oerate under: */
+#define USB_PD_CAP_CONSUMER_BC (1 << 0) /* BC */
+#define USB_PD_CAP_CONSUMER_PD (1 << 1) /* PD */
+#define USB_PD_CAP_CONSUMER_TYPE_C (1 << 2) /* USB Type-C Current */
+ __le16 wMinVoltage; /* in 50mV units */
+ __le16 wMaxVoltage; /* in 50mV units */
+ __u16 wReserved;
+ __le32 dwMaxOperatingPower; /* in 10 mW - operating at steady state */
+ __le32 dwMaxPeakPower; /* in 10mW units - operating at peak power */
+ __le32 dwMaxPeakPowerTime; /* in 100ms units - duration of peak */
+#define USB_PD_CAP_CONSUMER_UNKNOWN_PEAK_POWER_TIME 0xffff
+} __attribute__((packed));
+
+struct usb_pd_cap_provider_port_descriptor {
+ __u8 bLength;
+ __u8 bDescriptorType;
+ __u8 bDevCapabilityType;
+ __u8 bReserved1;
+ __u8 bmCapabilities;
+/* port will oerate under: */
+#define USB_PD_CAP_PROVIDER_BC (1 << 0) /* BC */
+#define USB_PD_CAP_PROVIDER_PD (1 << 1) /* PD */
+#define USB_PD_CAP_PROVIDER_TYPE_C (1 << 2) /* USB Type-C Current */
+ __u8 bNumOfPDObjects;
+ __u8 bReserved2;
+ __le32 wPowerDataObject[];
+} __attribute__((packed));
+
+/*
+ * Precision time measurement capability descriptor: advertised by devices and
+ * hubs that support PTM
+ */
+#define USB_PTM_CAP_TYPE 0xb
+struct usb_ptm_cap_descriptor {
+ __u8 bLength;
+ __u8 bDescriptorType;
+ __u8 bDevCapabilityType;
+} __attribute__((packed));
+
+#define USB_DT_USB_PTM_ID_SIZE 3
+/*
+ * The size of the descriptor for the Sublink Speed Attribute Count
+ * (SSAC) specified in bmAttributes[4:0]. SSAC is zero-based
+ */
+#define USB_DT_USB_SSP_CAP_SIZE(ssac) (12 + (ssac + 1) * 4)
+
/*-------------------------------------------------------------------------*/
/* USB_DT_WIRELESS_ENDPOINT_COMP: companion descriptor associated with
USB_SPEED_HIGH, /* usb 2.0 */
USB_SPEED_WIRELESS, /* wireless (usb 2.5) */
USB_SPEED_SUPER, /* usb 3.0 */
+ USB_SPEED_SUPER_PLUS, /* usb 3.1 */
};
+
enum usb_device_state {
/* NOTATTACHED isn't in the USB spec, and this state acts
* the same as ATTACHED ... but it's clearer this way.
*/
};
+enum usb3_link_state {
+ USB3_LPM_U0 = 0,
+ USB3_LPM_U1,
+ USB3_LPM_U2,
+ USB3_LPM_U3
+};
+
+/*
+ * A U1 timeout of 0x0 means the parent hub will reject any transitions to U1.
+ * 0xff means the parent hub will accept transitions to U1, but will not
+ * initiate a transition.
+ *
+ * A U1 timeout of 0x1 to 0x7F also causes the hub to initiate a transition to
+ * U1 after that many microseconds. Timeouts of 0x80 to 0xFE are reserved
+ * values.
+ *
+ * A U2 timeout of 0x0 means the parent hub will reject any transitions to U2.
+ * 0xff means the parent hub will accept transitions to U2, but will not
+ * initiate a transition.
+ *
+ * A U2 timeout of 0x1 to 0xFE also causes the hub to initiate a transition to
+ * U2 after N*256 microseconds. Therefore a U2 timeout value of 0x1 means a U2
+ * idle timer of 256 microseconds, 0x2 means 512 microseconds, 0xFE means
+ * 65.024ms.
+ */
+#define USB3_LPM_DISABLED 0x0
+#define USB3_LPM_U1_MAX_TIMEOUT 0x7F
+#define USB3_LPM_U2_MAX_TIMEOUT 0xFE
+#define USB3_LPM_DEVICE_INITIATED 0xFF
+
+struct usb_set_sel_req {
+ __u8 u1_sel;
+ __u8 u1_pel;
+ __le16 u2_sel;
+ __le16 u2_pel;
+} __attribute__ ((packed));
+
+/*
+ * The Set System Exit Latency control transfer provides one byte each for
+ * U1 SEL and U1 PEL, so the max exit latency is 0xFF. U2 SEL and U2 PEL each
+ * are two bytes long.
+ */
+#define USB3_LPM_MAX_U1_SEL_PEL 0xFF
+#define USB3_LPM_MAX_U2_SEL_PEL 0xFFFF
+
+/*-------------------------------------------------------------------------*/
+
+/*
+ * As per USB compliance update, a device that is actively drawing
+ * more than 100mA from USB must report itself as bus-powered in
+ * the GetStatus(DEVICE) call.
+ * https://compliance.usb.org/index.asp?UpdateFile=Electrical&Format=Standard#34
+ */
+#define USB_SELF_POWER_VBUS_MAX_DRAW 100
+
#endif /* __LINUX_USB_CH9_H */
projects / linux-libre-firmware.git / blobdiff