--- /dev/null
+/*
+ * fw/board_rzusb.c - RZUSB Board-specific functions (for boot loader and application)
+ *
+ * Written 2016 by Stefan Schmidt
+ * Copyright 2016 Stefan Schmidt
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+
+#include <stdbool.h>
+#include <stdint.h>
+
+#include <avr/io.h>
+#include <avr/interrupt.h>
+#include <avr/boot.h>
+
+#define F_CPU 8000000UL
+#include <util/delay.h>
+
+#include "usb.h"
+#include "at86rf230.h"
+#include "board.h"
+#include "spi.h"
+#include "usb/usb.h"
+
+static bool spi_initialized = 0;
+
+void reset_rf(void)
+{
+ /* set up all the outputs; default port value is 0 */
+
+ DDRB = 0;
+ DDRC = 0;
+ DDRD = 0;
+ PORTB = 0;
+ PORTC = 0;
+ PORTD = 0;
+
+ OUT(LED);
+ OUT(nRST_RF); /* this also resets the transceiver */
+ OUT(SLP_TR);
+
+ spi_init();
+
+ /* AT86RF231 data sheet, 12.4.13, reset pulse width: 625 ns (min) */
+
+ CLR(nRST_RF);
+ _delay_us(2);
+ SET(nRST_RF);
+
+ /* 12.4.14: SPI access latency after reset: 625 ns (min) */
+
+ _delay_us(2);
+
+ /* we must restore TRX_CTRL_0 after each reset (9.6.4) */
+
+ set_clkm();
+}
+
+void led(bool on)
+{
+ if (on)
+ SET(LED);
+ else
+ CLR(LED);
+}
+
+void set_clkm(void)
+{
+ /* switch CLKM to 8 MHz */
+
+ /*
+ * @@@ Note: Atmel advise against changing the external clock in
+ * mid-flight. We should therefore switch to the RC clock first, then
+ * crank up the external clock, and finally switch back to the external
+ * clock. The clock switching procedure is described in the ATmega32U2
+ * data sheet in secton 8.2.2.
+ */
+ spi_begin();
+ spi_send(AT86RF230_REG_WRITE | REG_TRX_CTRL_0);
+ spi_send(0x10);
+ spi_end();
+
+ /* TX_AUTO_CRC_ON, default disabled */
+ spi_begin();
+ spi_send(AT86RF230_REG_WRITE | 0x05);
+ spi_send(0x80);
+ spi_end();
+}
+
+void board_init(void)
+{
+ /* Disable the watchdog timer */
+
+ MCUSR = 0; /* Remove override */
+ WDTCSR |= 1 << WDCE; /* Enable change */
+ WDTCSR = 1 << WDCE; /* Disable watchdog while still enabling
+ change */
+
+ CLKPR = 1 << CLKPCE;
+ /* We start with a 16 MHz/8 clock. Put the prescaler to 2. */
+ CLKPR = 1 << CLKPS0;
+
+ get_sernum();
+}
+
+void spi_begin(void)
+{
+ if (!spi_initialized)
+ spi_init();
+ CLR(nSS);
+}
+
+void spi_off(void)
+{
+ spi_initialized = 0;
+ SPCR &= ~(1 << SPE);
+}
+
+void spi_init(void)
+{
+ SET(nSS);
+ OUT(SCLK);
+ OUT(MOSI);
+ OUT(nSS);
+ IN(MISO);
+
+ SPCR = (1 << SPE) | (1 << MSTR);
+ SPSR = (1 << SPI2X);
+
+ spi_initialized = 1;
+}
+
+void usb_init(void)
+{
+ USBCON |= 1 << FRZCLK; /* freeze the clock */
+
+ /* enable the PLL and wait for it to lock */
+ /* TODO sheet page 50 For Atmel AT90USB128x only. Do not use with Atmel AT90USB64x. */
+ /* FOR 8 XTAL Mhz only!!! */
+ PLLCSR = ((1 << PLLP1) | (1 << PLLP0));
+ PLLCSR |= 1 << PLLE;
+ while (!(PLLCSR & (1 << PLOCK)));
+
+ UHWCON |= (1 << UVREGE);
+
+ USBCON &= ~((1 << USBE) | (1 << OTGPADE)); /* reset the controller */
+ USBCON |= ((1 << USBE) | (1 << OTGPADE));
+
+ USBCON &= ~(1 << FRZCLK); /* thaw the clock */
+
+ UDCON &= ~(1 << DETACH); /* attach the pull-up */
+ UDIEN = 1 << EORSTE; /* enable device interrupts */
+// UDCON |= 1 << RSTCPU; /* reset CPU on bus reset */
+
+ ep_init();
+}
+
+void board_app_init(void)
+{
+ /* enable timer input capture 1, trigger on rising edge */
+ TCCR1B = (1 << ICES1);
+ TIFR1 = (1 << ICF1);
+ TIMSK1 = (1 << ICIE1);
+}