#define IEEE80211_MAX_MESH_ID_LEN 32
+#define IEEE80211_NUM_TIDS 16
+
#define IEEE80211_QOS_CTL_LEN 2
/* 1d tag mask */
#define IEEE80211_QOS_CTL_TAG1D_MASK 0x0007
u8 meshconf_cap;
} __attribute__ ((packed));
+/**
+ * enum mesh_config_capab_flags - Mesh Configuration IE capability field flags
+ *
+ * @IEEE80211_MESHCONF_CAPAB_ACCEPT_PLINKS: STA is willing to establish
+ * additional mesh peerings with other mesh STAs
+ * @IEEE80211_MESHCONF_CAPAB_FORWARDING: the STA forwards MSDUs
+ * @IEEE80211_MESHCONF_CAPAB_TBTT_ADJUSTING: TBTT adjustment procedure
+ * is ongoing
+ */
+enum mesh_config_capab_flags {
+ IEEE80211_MESHCONF_CAPAB_ACCEPT_PLINKS = 0x01,
+ IEEE80211_MESHCONF_CAPAB_FORWARDING = 0x08,
+ IEEE80211_MESHCONF_CAPAB_TBTT_ADJUSTING = 0x20,
+};
+
/**
* struct ieee80211_rann_ie
*
} u;
} __packed;
+/*
+ * Peer-to-Peer IE attribute related definitions.
+ */
+/**
+ * enum ieee80211_p2p_attr_id - identifies type of peer-to-peer attribute.
+ */
+enum ieee80211_p2p_attr_id {
+ IEEE80211_P2P_ATTR_STATUS = 0,
+ IEEE80211_P2P_ATTR_MINOR_REASON,
+ IEEE80211_P2P_ATTR_CAPABILITY,
+ IEEE80211_P2P_ATTR_DEVICE_ID,
+ IEEE80211_P2P_ATTR_GO_INTENT,
+ IEEE80211_P2P_ATTR_GO_CONFIG_TIMEOUT,
+ IEEE80211_P2P_ATTR_LISTEN_CHANNEL,
+ IEEE80211_P2P_ATTR_GROUP_BSSID,
+ IEEE80211_P2P_ATTR_EXT_LISTEN_TIMING,
+ IEEE80211_P2P_ATTR_INTENDED_IFACE_ADDR,
+ IEEE80211_P2P_ATTR_MANAGABILITY,
+ IEEE80211_P2P_ATTR_CHANNEL_LIST,
+ IEEE80211_P2P_ATTR_ABSENCE_NOTICE,
+ IEEE80211_P2P_ATTR_DEVICE_INFO,
+ IEEE80211_P2P_ATTR_GROUP_INFO,
+ IEEE80211_P2P_ATTR_GROUP_ID,
+ IEEE80211_P2P_ATTR_INTERFACE,
+ IEEE80211_P2P_ATTR_OPER_CHANNEL,
+ IEEE80211_P2P_ATTR_INVITE_FLAGS,
+ /* 19 - 220: Reserved */
+ IEEE80211_P2P_ATTR_VENDOR_SPECIFIC = 221,
+
+ IEEE80211_P2P_ATTR_MAX
+};
+
/**
* struct ieee80211_bar - HT Block Ack Request
*
* STA can receive. Rate expressed in units of 1 Mbps.
* If this field is 0 this value should not be used to
* consider the highest RX data rate supported.
+ * The top 3 bits of this field are reserved.
* @tx_mcs_map: TX MCS map 2 bits for each stream, total 8 streams
* @tx_highest: Indicates highest long GI VHT PPDU data rate
* STA can transmit. Rate expressed in units of 1 Mbps.
* If this field is 0 this value should not be used to
* consider the highest TX data rate supported.
+ * The top 3 bits of this field are reserved.
*/
struct ieee80211_vht_mcs_info {
__le16 rx_mcs_map;
__le16 tx_highest;
} __packed;
+/**
+ * enum ieee80211_vht_mcs_support - VHT MCS support definitions
+ * @IEEE80211_VHT_MCS_SUPPORT_0_7: MCSes 0-7 are supported for the
+ * number of streams
+ * @IEEE80211_VHT_MCS_SUPPORT_0_8: MCSes 0-8 are supported
+ * @IEEE80211_VHT_MCS_SUPPORT_0_9: MCSes 0-9 are supported
+ * @IEEE80211_VHT_MCS_NOT_SUPPORTED: This number of streams isn't supported
+ *
+ * These definitions are used in each 2-bit subfield of the @rx_mcs_map
+ * and @tx_mcs_map fields of &struct ieee80211_vht_mcs_info, which are
+ * both split into 8 subfields by number of streams. These values indicate
+ * which MCSes are supported for the number of streams the value appears
+ * for.
+ */
+enum ieee80211_vht_mcs_support {
+ IEEE80211_VHT_MCS_SUPPORT_0_7 = 0,
+ IEEE80211_VHT_MCS_SUPPORT_0_8 = 1,
+ IEEE80211_VHT_MCS_SUPPORT_0_9 = 2,
+ IEEE80211_VHT_MCS_NOT_SUPPORTED = 3,
+};
+
/**
* struct ieee80211_vht_cap - VHT capabilities
*
struct ieee80211_vht_mcs_info supp_mcs;
} __packed;
+/**
+ * enum ieee80211_vht_chanwidth - VHT channel width
+ * @IEEE80211_VHT_CHANWIDTH_USE_HT: use the HT operation IE to
+ * determine the channel width (20 or 40 MHz)
+ * @IEEE80211_VHT_CHANWIDTH_80MHZ: 80 MHz bandwidth
+ * @IEEE80211_VHT_CHANWIDTH_160MHZ: 160 MHz bandwidth
+ * @IEEE80211_VHT_CHANWIDTH_80P80MHZ: 80+80 MHz bandwidth
+ */
+enum ieee80211_vht_chanwidth {
+ IEEE80211_VHT_CHANWIDTH_USE_HT = 0,
+ IEEE80211_VHT_CHANWIDTH_80MHZ = 1,
+ IEEE80211_VHT_CHANWIDTH_160MHZ = 2,
+ IEEE80211_VHT_CHANWIDTH_80P80MHZ = 3,
+};
+
/**
* struct ieee80211_vht_operation - VHT operation IE
*