#define IEEE80211_MAX_MESH_ID_LEN 32
+#define IEEE80211_NUM_TIDS 16
+
#define IEEE80211_QOS_CTL_LEN 2
/* 1d tag mask */
#define IEEE80211_QOS_CTL_TAG1D_MASK 0x0007
u8 meshconf_cap;
} __attribute__ ((packed));
+/**
+ * enum mesh_config_capab_flags - Mesh Configuration IE capability field flags
+ *
+ * @IEEE80211_MESHCONF_CAPAB_ACCEPT_PLINKS: STA is willing to establish
+ * additional mesh peerings with other mesh STAs
+ * @IEEE80211_MESHCONF_CAPAB_FORWARDING: the STA forwards MSDUs
+ * @IEEE80211_MESHCONF_CAPAB_TBTT_ADJUSTING: TBTT adjustment procedure
+ * is ongoing
+ */
+enum mesh_config_capab_flags {
+ IEEE80211_MESHCONF_CAPAB_ACCEPT_PLINKS = 0x01,
+ IEEE80211_MESHCONF_CAPAB_FORWARDING = 0x08,
+ IEEE80211_MESHCONF_CAPAB_TBTT_ADJUSTING = 0x20,
+};
+
/**
* struct ieee80211_rann_ie
*
} u;
} __packed;
+/*
+ * Peer-to-Peer IE attribute related definitions.
+ */
+/**
+ * enum ieee80211_p2p_attr_id - identifies type of peer-to-peer attribute.
+ */
+enum ieee80211_p2p_attr_id {
+ IEEE80211_P2P_ATTR_STATUS = 0,
+ IEEE80211_P2P_ATTR_MINOR_REASON,
+ IEEE80211_P2P_ATTR_CAPABILITY,
+ IEEE80211_P2P_ATTR_DEVICE_ID,
+ IEEE80211_P2P_ATTR_GO_INTENT,
+ IEEE80211_P2P_ATTR_GO_CONFIG_TIMEOUT,
+ IEEE80211_P2P_ATTR_LISTEN_CHANNEL,
+ IEEE80211_P2P_ATTR_GROUP_BSSID,
+ IEEE80211_P2P_ATTR_EXT_LISTEN_TIMING,
+ IEEE80211_P2P_ATTR_INTENDED_IFACE_ADDR,
+ IEEE80211_P2P_ATTR_MANAGABILITY,
+ IEEE80211_P2P_ATTR_CHANNEL_LIST,
+ IEEE80211_P2P_ATTR_ABSENCE_NOTICE,
+ IEEE80211_P2P_ATTR_DEVICE_INFO,
+ IEEE80211_P2P_ATTR_GROUP_INFO,
+ IEEE80211_P2P_ATTR_GROUP_ID,
+ IEEE80211_P2P_ATTR_INTERFACE,
+ IEEE80211_P2P_ATTR_OPER_CHANNEL,
+ IEEE80211_P2P_ATTR_INVITE_FLAGS,
+ /* 19 - 220: Reserved */
+ IEEE80211_P2P_ATTR_VENDOR_SPECIFIC = 221,
+
+ IEEE80211_P2P_ATTR_MAX
+};
+
/**
* struct ieee80211_bar - HT Block Ack Request
*
#define WLAN_HT_SMPS_CONTROL_STATIC 1
#define WLAN_HT_SMPS_CONTROL_DYNAMIC 3
-#define VHT_MCS_SUPPORTED_SET_SIZE 8
-
-struct ieee80211_vht_capabilities {
- __le32 vht_capabilities_info;
- u8 vht_supported_mcs_set[VHT_MCS_SUPPORTED_SET_SIZE];
-} __packed;
-
-struct ieee80211_vht_operation {
- u8 vht_op_info_chwidth;
- u8 vht_op_info_chan_center_freq_seg1_idx;
- u8 vht_op_info_chan_center_freq_seg2_idx;
- __le16 vht_basic_mcs_set;
-} __packed;
-
/**
* struct ieee80211_vht_mcs_info - VHT MCS information
* @rx_mcs_map: RX MCS map 2 bits for each stream, total 8 streams
* STA can receive. Rate expressed in units of 1 Mbps.
* If this field is 0 this value should not be used to
* consider the highest RX data rate supported.
+ * The top 3 bits of this field are reserved.
* @tx_mcs_map: TX MCS map 2 bits for each stream, total 8 streams
* @tx_highest: Indicates highest long GI VHT PPDU data rate
* STA can transmit. Rate expressed in units of 1 Mbps.
* If this field is 0 this value should not be used to
* consider the highest TX data rate supported.
+ * The top 3 bits of this field are reserved.
*/
struct ieee80211_vht_mcs_info {
__le16 rx_mcs_map;
__le16 tx_highest;
} __packed;
+/**
+ * enum ieee80211_vht_mcs_support - VHT MCS support definitions
+ * @IEEE80211_VHT_MCS_SUPPORT_0_7: MCSes 0-7 are supported for the
+ * number of streams
+ * @IEEE80211_VHT_MCS_SUPPORT_0_8: MCSes 0-8 are supported
+ * @IEEE80211_VHT_MCS_SUPPORT_0_9: MCSes 0-9 are supported
+ * @IEEE80211_VHT_MCS_NOT_SUPPORTED: This number of streams isn't supported
+ *
+ * These definitions are used in each 2-bit subfield of the @rx_mcs_map
+ * and @tx_mcs_map fields of &struct ieee80211_vht_mcs_info, which are
+ * both split into 8 subfields by number of streams. These values indicate
+ * which MCSes are supported for the number of streams the value appears
+ * for.
+ */
+enum ieee80211_vht_mcs_support {
+ IEEE80211_VHT_MCS_SUPPORT_0_7 = 0,
+ IEEE80211_VHT_MCS_SUPPORT_0_8 = 1,
+ IEEE80211_VHT_MCS_SUPPORT_0_9 = 2,
+ IEEE80211_VHT_MCS_NOT_SUPPORTED = 3,
+};
+
+/**
+ * struct ieee80211_vht_cap - VHT capabilities
+ *
+ * This structure is the "VHT capabilities element" as
+ * described in 802.11ac D3.0 8.4.2.160
+ * @vht_cap_info: VHT capability info
+ * @supp_mcs: VHT MCS supported rates
+ */
+struct ieee80211_vht_cap {
+ __le32 vht_cap_info;
+ struct ieee80211_vht_mcs_info supp_mcs;
+} __packed;
+
+/**
+ * enum ieee80211_vht_chanwidth - VHT channel width
+ * @IEEE80211_VHT_CHANWIDTH_USE_HT: use the HT operation IE to
+ * determine the channel width (20 or 40 MHz)
+ * @IEEE80211_VHT_CHANWIDTH_80MHZ: 80 MHz bandwidth
+ * @IEEE80211_VHT_CHANWIDTH_160MHZ: 160 MHz bandwidth
+ * @IEEE80211_VHT_CHANWIDTH_80P80MHZ: 80+80 MHz bandwidth
+ */
+enum ieee80211_vht_chanwidth {
+ IEEE80211_VHT_CHANWIDTH_USE_HT = 0,
+ IEEE80211_VHT_CHANWIDTH_80MHZ = 1,
+ IEEE80211_VHT_CHANWIDTH_160MHZ = 2,
+ IEEE80211_VHT_CHANWIDTH_80P80MHZ = 3,
+};
+
+/**
+ * struct ieee80211_vht_operation - VHT operation IE
+ *
+ * This structure is the "VHT operation element" as
+ * described in 802.11ac D3.0 8.4.2.161
+ * @chan_width: Operating channel width
+ * @center_freq_seg1_idx: center freq segment 1 index
+ * @center_freq_seg2_idx: center freq segment 2 index
+ * @basic_mcs_set: VHT Basic MCS rate set
+ */
+struct ieee80211_vht_operation {
+ u8 chan_width;
+ u8 center_freq_seg1_idx;
+ u8 center_freq_seg2_idx;
+ __le16 basic_mcs_set;
+} __packed;
+
+
#define IEEE80211_VHT_MCS_ZERO_TO_SEVEN_SUPPORT 0
#define IEEE80211_VHT_MCS_ZERO_TO_EIGHT_SUPPORT 1
#define IEEE80211_VHT_MCS_ZERO_TO_NINE_SUPPORT 2
#define IEEE80211_VHT_MCS_NOT_SUPPORTED 3
/* 802.11ac VHT Capabilities */
-#define IEEE80211_VHT_CAP_MAX_MPDU_LENGTH_3895 0x00000000
-#define IEEE80211_VHT_CAP_MAX_MPDU_LENGTH_7991 0x00000001
-#define IEEE80211_VHT_CAP_MAX_MPDU_LENGTH_11454 0x00000002
-#define IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ 0x00000004
-#define IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ 0x00000008
-#define IEEE80211_VHT_CAP_RXLDPC 0x00000010
-#define IEEE80211_VHT_CAP_SHORT_GI_80 0x00000020
-#define IEEE80211_VHT_CAP_SHORT_GI_160 0x00000040
-#define IEEE80211_VHT_CAP_TXSTBC 0x00000080
-#define IEEE80211_VHT_CAP_RXSTBC_1 0x00000100
-#define IEEE80211_VHT_CAP_RXSTBC_2 0x00000200
-#define IEEE80211_VHT_CAP_RXSTBC_3 0x00000300
-#define IEEE80211_VHT_CAP_RXSTBC_4 0x00000400
-#define IEEE80211_VHT_CAP_SU_BEAMFORMER_CAPABLE 0x00000800
-#define IEEE80211_VHT_CAP_SU_BEAMFORMEE_CAPABLE 0x00001000
-#define IEEE80211_VHT_CAP_BEAMFORMER_ANTENNAS_MAX 0x00006000
-#define IEEE80211_VHT_CAP_SOUNDING_DIMENTION_MAX 0x00030000
-#define IEEE80211_VHT_CAP_MU_BEAMFORMER_CAPABLE 0x00080000
-#define IEEE80211_VHT_CAP_MU_BEAMFORMEE_CAPABLE 0x00100000
-#define IEEE80211_VHT_CAP_VHT_TXOP_PS 0x00200000
-#define IEEE80211_VHT_CAP_HTC_VHT 0x00400000
-#define IEEE80211_VHT_CAP_MAX_A_MPDU_LENGTH_EXPONENT 0x00800000
-#define IEEE80211_VHT_CAP_VHT_LINK_ADAPTATION_VHT_UNSOL_MFB 0x08000000
-#define IEEE80211_VHT_CAP_VHT_LINK_ADAPTATION_VHT_MRQ_MFB 0x0c000000
-#define IEEE80211_VHT_CAP_RX_ANTENNA_PATTERN 0x10000000
-#define IEEE80211_VHT_CAP_TX_ANTENNA_PATTERN 0x20000000
+#define IEEE80211_VHT_CAP_MAX_MPDU_LENGTH_3895 0x00000000
+#define IEEE80211_VHT_CAP_MAX_MPDU_LENGTH_7991 0x00000001
+#define IEEE80211_VHT_CAP_MAX_MPDU_LENGTH_11454 0x00000002
+#define IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160MHZ 0x00000004
+#define IEEE80211_VHT_CAP_SUPP_CHAN_WIDTH_160_80PLUS80MHZ 0x00000008
+#define IEEE80211_VHT_CAP_RXLDPC 0x00000010
+#define IEEE80211_VHT_CAP_SHORT_GI_80 0x00000020
+#define IEEE80211_VHT_CAP_SHORT_GI_160 0x00000040
+#define IEEE80211_VHT_CAP_TXSTBC 0x00000080
+#define IEEE80211_VHT_CAP_RXSTBC_1 0x00000100
+#define IEEE80211_VHT_CAP_RXSTBC_2 0x00000200
+#define IEEE80211_VHT_CAP_RXSTBC_3 0x00000300
+#define IEEE80211_VHT_CAP_RXSTBC_4 0x00000400
+#define IEEE80211_VHT_CAP_SU_BEAMFORMER_CAPABLE 0x00000800
+#define IEEE80211_VHT_CAP_SU_BEAMFORMEE_CAPABLE 0x00001000
+#define IEEE80211_VHT_CAP_BEAMFORMER_ANTENNAS_MAX 0x00006000
+#define IEEE80211_VHT_CAP_SOUNDING_DIMENTION_MAX 0x00030000
+#define IEEE80211_VHT_CAP_MU_BEAMFORMER_CAPABLE 0x00080000
+#define IEEE80211_VHT_CAP_MU_BEAMFORMEE_CAPABLE 0x00100000
+#define IEEE80211_VHT_CAP_VHT_TXOP_PS 0x00200000
+#define IEEE80211_VHT_CAP_HTC_VHT 0x00400000
+#define IEEE80211_VHT_CAP_MAX_A_MPDU_LENGTH_EXPONENT_SHIFT 23
+#define IEEE80211_VHT_CAP_MAX_A_MPDU_LENGTH_EXPONENT_MASK \
+ (7 << IEEE80211_VHT_CAP_MAX_A_MPDU_LENGTH_EXPONENT_SHIFT)
+#define IEEE80211_VHT_CAP_VHT_LINK_ADAPTATION_VHT_UNSOL_MFB 0x08000000
+#define IEEE80211_VHT_CAP_VHT_LINK_ADAPTATION_VHT_MRQ_MFB 0x0c000000
+#define IEEE80211_VHT_CAP_RX_ANTENNA_PATTERN 0x10000000
+#define IEEE80211_VHT_CAP_TX_ANTENNA_PATTERN 0x20000000
/* Authentication algorithms */
#define WLAN_AUTH_OPEN 0
WLAN_EID_RSN = 48,
WLAN_EID_MMIE = 76,
- WLAN_EID_WPA = 221,
- WLAN_EID_GENERIC = 221,
WLAN_EID_VENDOR_SPECIFIC = 221,
WLAN_EID_QOS_PARAMETER = 222,
projects / carl9170fw.git / blobdiff