kconfig: split the lexer out of zconf.y

[carl9170fw.git] / carlfw / Kconfig

diff --git a/carlfw/Kconfig b/carlfw/Kconfig
index d1a68a1c60b813497a3268db6960468bdf92d8d3..46eb1bb87399f5ba4250d43d71a5d05daa9412fe 100644 (file)
--- a/carlfw/Kconfig
+++ b/carlfw/Kconfig
@@ -31,15 +31,6 @@ config CARL9170FW_RX_FRAME_LEN
        default 16384 if CARL9170FW_RX_FRAME_LEN_16384
        default 32768 if CARL9170FW_RX_FRAME_LEN_32768
 
-config CARL9170FW_WATCHDOG
-       def_bool y
-       prompt "Activate HW Watchdog"
-       ---help---
-        The watchdog will notify the application as soon as the firmware
-        has stalled.
-
-        Say Y.
-
 config CARL9170FW_GPIO_INTERRUPT
        def_bool y
        prompt "GPIO Software Interrupt"
@@ -74,35 +65,6 @@ config CARL9170FW_RADIO_FUNCTIONS
 
 endmenu
 
-menu "802.11 Firmware Features"
-
-config CARL9170FW_HANDLE_BACK_REQ
-       def_bool y
-       prompt "Handle BlockACK Requests in Firmware"
-       ---help---
-        Enables a firmware mechanism to answer incoming BlockACK requests.
-        This feature is necessary to comply with 802.11n. So say Y,
-        if you have plans to support this operation mode.
-
-config CARL9170FW_BACK_REQS_NUM
-       default 4
-       int
-       prompt "Number of max. active BlockACK Request"
-       depends on CARL9170FW_HANDLE_BACK_REQ
-
-config CARL9170FW_CAB_QUEUE
-       def_bool y
-       prompt "Support software-based Content after Beacon Queue"
-       ---help---
-        This (software) queue is used to send any broad-/multi-cast buffered
-        frames after the next DTIM beacon.
-
-        This feature is required for Accesspoint mode operation.
-
-        Say Y.
-
-endmenu
-
 source "carlfw/usb/Kconfig"
 
 menu "Experimental, Unstable & Testing Extensions"
@@ -123,34 +85,6 @@ config CARL9170FW_EXPERIMENTAL
        def_bool y
        prompt "Experimental Features"
 
-config CARL9170FW_PSM
-       def_bool y
-       prompt "Firmware Supported Power-saving Management"
-       depends on CARL9170FW_EXPERIMENTAL && CARL9170FW_RADIO_FUNCTIONS
-       ---help---
-        This options enables a interface for the application to
-        switch off the RF/PHY (in order to save power). And the
-        Firmware will automatically turn it on again, when the
-        PRETBTT event fires.
-
-config CARL9170FW_DELAYED_TX
-       def_bool n
-       prompt "Delay and reorder TX"
-       depends on CARL9170FW_EXPERIMENTAL
-       ---help---
-        Delay incoming TX' from the application until wlan_complete
-        has finished.
-
-        This feature is necessary to keep A-MPDUs partially ordered.
-
-        Doesn't work 100% yet, but in most cases other HW designs can
-        deal with the fallout.
-
-config CARL9170FW_TX_AMPDU
-       def_bool n
-       prompt "Firmware-supported ampdu scheduling"
-       depends on CARL9170FW_EXPERIMENTAL
-
 config CARL9170FW_WOL_OPTION
        def_bool n
        prompt "Wakeup on WLAN"
@@ -164,13 +98,15 @@ config CARL9170FW_WOL
        def_bool n
        depends on CARL9170FW_WOL_OPTION
 
-config CARL9170FW_WOL_MAGIC_PACKET
+config CARL9170FW_WOL_NL80211_TRIGGERS
        def_bool n
-       prompt "Magic Packet(tm)"
+       prompt "Standard NL80211 wakeup triggers"
        depends on CARL9170FW_WOL_OPTION
        select CARL9170FW_WOL
        ---help---
-        Sniff all incoming data frames for the magic packet pattern.
+        Available triggers:
+         * Magic Packet(tm) pattern
+         * disconnect event
 
 config CARL9170FW_WOL_PROBE_REQUEST
        def_bool n
@@ -197,9 +133,24 @@ config CARL9170FW_FW_MAC_RESET
        prompt "Firmware MAC Chip recovery"
        depends on CARL9170FW_EXPERIMENTAL
 
+config CARL9170FW_NOISY_MAC_RESET
+       def_bool n
+       prompt "Notify MAC RESET events"
+       depends on CARL9170FW_FW_MAC_RESET
+
+config CARL9170FW_80MHZ_CLOCK
+       def_bool n
+       prompt "Allow 80/88MHz clock for HT40"
+       depends on CARL9170FW_EXPERIMENTAL
+       ---help---
+        The SoC can run up to 80/88MHz in HT40 mode. This improves
+        throughput and timing accuracy over the 40/44MHz clock.
+        However some devices don't have heat shields and they with
+        this option enabled, they become unstable under load.
+
 config CARL9170FW_BROKEN_FEATURES
        def_bool n
-       prompt "Broken Featurs"
+       prompt "Broken Features"
 
 config CARL9170FW_DEBUG
        def_bool n
@@ -226,7 +177,7 @@ config CARL9170FW_DEBUG_UART
 
 config CARL9170FW_WATCHDOG_BUTTON
        def_bool n
-       depends on CARL9170FW_BROKEN && CARL9170FW_WATCHDOG && CARL9170FW_GPIO_INTERRUPT
+       depends on CARL9170FW_BROKEN && CARL9170FW_GPIO_INTERRUPT
        prompt "Trigger Watchdog by pressing the WPS button"
 
 choice CARL9170FW_UART_CLOCK
@@ -242,40 +193,14 @@ config CARL9170FW_UART_CLOCK_40M
 
 endchoice
 
-
-choice
-       prompt "TX / RX Path"
-
-       default CARL9170FW_NORMAL_TX_RX
-
-       config CARL9170FW_NORMAL_TX_RX
-               bool
-               prompt "Normal WLAN TX/RX routines"
-
-       config CARL9170FW_LOOPBACK
-               bool
-               depends on CARL9170FW_BROKEN_FEATURES
-               prompt "TX->(tx feedback)->RX loopback"
-               ---help---
-                Useful carlu testcase.
-
-       config CARL9170FW_DISCARD
-               bool
-               depends on CARL9170FW_BROKEN_FEATURES
-               prompt "TX->(tx feedback)"
-               ---help---
-                Useful carlu testcase
-
-endchoice
-
 config CARL9170FW_UNUSABLE
        def_bool y
-       depends on CARL9170FW_BROKEN || CARL9170FW_LOOPBACK
+       depends on CARL9170FW_BROKEN || CARL9170FW_DEBUG
 
 config CARL9170FW_USB_MODESWITCH
        def_bool n
        prompt "USB 1.1 / 2.0 switching support"
-       depends on CARL9170FW_BROKEN_FEATURES
+       depends on CARL9170FW_BROKEN_FEATURES && CARL9170FW_USB_STANDARD_CMDS
        ---help---
         Mostly implemented, but untested and some serious
         doubts remain.