config CARL9170FW_GPIO_INTERRUPT
def_bool y
prompt "GPIO Software Interrupt"
- ---help---
+ help
When this option is enabled, the firmware will poll the GPIO
registers and reports to the driver whenever the GPIO state
has changed from a previous state.
config CARL9170FW_SECURITY_ENGINE
def_bool y
prompt "Support Hardware Crypto Engine"
- ---help---
+ help
This options controls if the firmware will allow the driver
to program the security engine / CAM through a firmware
interface.
config CARL9170FW_RADIO_FUNCTIONS
def_bool y
prompt "Enable Firmware-supported Radio/RF functions"
- ---help---
+ help
Some PHY/RF functions (e.g.: AGC and Noise calibration) need
to be done in the firmware.
endmenu
-menu "802.11 Firmware Features"
-
-config CARL9170FW_HANDLE_BACK_REQ
- def_bool y
- prompt "Handle BlockACK Requests in Firmware"
- ---help---
- Enables a firmware mechanism to answer incoming BlockACK requests.
- This feature is necessary to comply with 802.11n. So say Y,
- if you have plans to support this operation mode.
-
-config CARL9170FW_BACK_REQS_NUM
- default 4
- int
- prompt "Number of max. active BlockACK Request"
- depends on CARL9170FW_HANDLE_BACK_REQ
-
-config CARL9170FW_CAB_QUEUE
- def_bool y
- prompt "Support software-based Content after Beacon Queue"
- ---help---
- This (software) queue is used to send any broad-/multi-cast buffered
- frames after the next DTIM beacon.
-
- This feature is required for Accesspoint mode operation.
-
- Say Y.
-
-endmenu
-
source "carlfw/usb/Kconfig"
menu "Experimental, Unstable & Testing Extensions"
def_bool y
prompt "Advanced printf"
depends on CARL9170FW_DEBUG_UART || CARL9170FW_DEBUG_USB
- ---help---
+ help
Advanced printf (very useful for debugging purposes)
The formats supported by this implementation are:
'd' 'u' 'c' 's' 'x' 'X' 'p'.
def_bool n
prompt "Wakeup on WLAN"
depends on CARL9170FW_EXPERIMENTAL
- ---help---
+ help
With this option enabled, the firmware can wake-up
suspended hosts... As long as they fully support
USB remote wakeup.
def_bool n
depends on CARL9170FW_WOL_OPTION
-config CARL9170FW_WOL_MAGIC_PACKET
+config CARL9170FW_WOL_NL80211_TRIGGERS
def_bool n
- prompt "Magic Packet(tm)"
+ prompt "Standard NL80211 wakeup triggers"
depends on CARL9170FW_WOL_OPTION
select CARL9170FW_WOL
- ---help---
- Sniff all incoming data frames for the magic packet pattern.
+ help
+ Available triggers:
+ * Magic Packet(tm) pattern
+ * disconnect event
config CARL9170FW_WOL_PROBE_REQUEST
def_bool n
prompt "Probe Request"
depends on CARL9170FW_WOL_OPTION
select CARL9170FW_WOL
- ---help---
+ help
Scan probe requests for a given SSID.
config CARL9170FW_WOL_PROBE_REQUEST_SSID
prompt "Notify MAC RESET events"
depends on CARL9170FW_FW_MAC_RESET
+config CARL9170FW_80MHZ_CLOCK
+ def_bool n
+ prompt "Allow 80/88MHz clock for HT40"
+ depends on CARL9170FW_EXPERIMENTAL
+ help
+ The SoC can run up to 80/88MHz in HT40 mode. This improves
+ throughput and timing accuracy over the 40/44MHz clock.
+ However some devices don't have heat shields and they with
+ this option enabled, they become unstable under load.
+
config CARL9170FW_BROKEN_FEATURES
def_bool n
- prompt "Broken Featurs"
+ prompt "Broken Features"
config CARL9170FW_DEBUG
def_bool n
def_bool n
prompt "LED Heartbeat"
depends on CARL9170FW_BROKEN_FEATURES
- ---help---
+ help
This option conflicts with the application's LED code.
Also, it assumes that you have two LEDs, which is not
necessarily true.
def_bool n
prompt "Pass debug messages through Highspeed UART"
depends on CARL9170FW_BROKEN_FEATURES
- ---help---
+ help
This option allows the firmware to send BUG/ERR/INFO/DBG and
hexdumps through the UART _as well_. However, first: you must
connect a working logger.
endchoice
-
-choice
- prompt "TX / RX Path"
-
- default CARL9170FW_NORMAL_TX_RX
-
- config CARL9170FW_NORMAL_TX_RX
- bool
- prompt "Normal WLAN TX/RX routines"
-
- config CARL9170FW_LOOPBACK
- bool
- depends on CARL9170FW_BROKEN_FEATURES
- prompt "TX->(tx feedback)->RX loopback"
- ---help---
- Useful carlu testcase.
-
- config CARL9170FW_DISCARD
- bool
- depends on CARL9170FW_BROKEN_FEATURES
- prompt "TX->(tx feedback)"
- ---help---
- Useful carlu testcase
-
-endchoice
-
config CARL9170FW_UNUSABLE
def_bool y
- depends on CARL9170FW_BROKEN || CARL9170FW_LOOPBACK
+ depends on CARL9170FW_BROKEN || CARL9170FW_DEBUG
config CARL9170FW_USB_MODESWITCH
def_bool n
prompt "USB 1.1 / 2.0 switching support"
- depends on CARL9170FW_BROKEN_FEATURES
- ---help---
+ depends on CARL9170FW_BROKEN_FEATURES && CARL9170FW_USB_STANDARD_CMDS
+ help
Mostly implemented, but untested and some serious
doubts remain.
config CARL9170FW_AGGRESSIVE_CFLAGS
def_bool y
prompt "Enable aggressive size optimization"
- ---help---
+ help
This option adds several more optimization compiler flags,
which can greatly reduce the firmware size... at the expense
of machine-code readability.