2 * P1022DS board specific routines
4 * Authors: Travis Wheatley <travis.wheatley@freescale.com>
5 * Dave Liu <daveliu@freescale.com>
6 * Timur Tabi <timur@freescale.com>
8 * Copyright 2010 Freescale Semiconductor, Inc.
10 * This file is taken from the Freescale P1022DS BSP, with modifications:
12 * 3) No PCI endpoint support
14 * This file is licensed under the terms of the GNU General Public License
15 * version 2. This program is licensed "as is" without any warranty of any
16 * kind, whether express or implied.
19 #include <linux/fsl/guts.h>
20 #include <linux/pci.h>
21 #include <linux/of_address.h>
22 #include <linux/of_platform.h>
23 #include <asm/div64.h>
25 #include <asm/swiotlb.h>
27 #include <sysdev/fsl_soc.h>
28 #include <sysdev/fsl_pci.h>
30 #include <asm/fsl_lbc.h>
35 #if defined(CONFIG_FB_FSL_DIU) || defined(CONFIG_FB_FSL_DIU_MODULE)
37 #define PMUXCR_ELBCDIU_MASK 0xc0000000
38 #define PMUXCR_ELBCDIU_NOR16 0x80000000
39 #define PMUXCR_ELBCDIU_DIU 0x40000000
42 * Board-specific initialization of the DIU. This code should probably be
43 * executed when the DIU is opened, rather than in arch code, but the DIU
44 * driver does not have a mechanism for this (yet).
46 * This is especially problematic on the P1022DS because the local bus (eLBC)
47 * and the DIU video signals share the same pins, which means that enabling the
48 * DIU will disable access to NOR flash.
51 /* DIU Pixel Clock bits of the CLKDVDR Global Utilities register */
52 #define CLKDVDR_PXCKEN 0x80000000
53 #define CLKDVDR_PXCKINV 0x10000000
54 #define CLKDVDR_PXCKDLY 0x06000000
55 #define CLKDVDR_PXCLK_MASK 0x00FF0000
57 /* Some ngPIXIS register definitions */
62 #define PX_BRDCFG0_ELBC_SPI_MASK 0xc0
63 #define PX_BRDCFG0_ELBC_SPI_ELBC 0x00
64 #define PX_BRDCFG0_ELBC_SPI_NULL 0xc0
65 #define PX_BRDCFG0_ELBC_DIU 0x02
67 #define PX_BRDCFG1_DVIEN 0x80
68 #define PX_BRDCFG1_DFPEN 0x40
69 #define PX_BRDCFG1_BACKLIGHT 0x20
70 #define PX_BRDCFG1_DDCEN 0x10
72 #define PX_CTL_ALTACC 0x80
77 * Note that we need to byte-swap the value before it's written to the AD
78 * register. So even though the registers don't look like they're in the same
79 * bit positions as they are on the MPC8610, the same value is written to the
80 * AD register on the MPC8610 and on the P1022.
82 #define AD_BYTE_F 0x10000000
83 #define AD_ALPHA_C_MASK 0x0E000000
84 #define AD_ALPHA_C_SHIFT 25
85 #define AD_BLUE_C_MASK 0x01800000
86 #define AD_BLUE_C_SHIFT 23
87 #define AD_GREEN_C_MASK 0x00600000
88 #define AD_GREEN_C_SHIFT 21
89 #define AD_RED_C_MASK 0x00180000
90 #define AD_RED_C_SHIFT 19
91 #define AD_PALETTE 0x00040000
92 #define AD_PIXEL_S_MASK 0x00030000
93 #define AD_PIXEL_S_SHIFT 16
94 #define AD_COMP_3_MASK 0x0000F000
95 #define AD_COMP_3_SHIFT 12
96 #define AD_COMP_2_MASK 0x00000F00
97 #define AD_COMP_2_SHIFT 8
98 #define AD_COMP_1_MASK 0x000000F0
99 #define AD_COMP_1_SHIFT 4
100 #define AD_COMP_0_MASK 0x0000000F
101 #define AD_COMP_0_SHIFT 0
103 #define MAKE_AD(alpha, red, blue, green, size, c0, c1, c2, c3) \
104 cpu_to_le32(AD_BYTE_F | (alpha << AD_ALPHA_C_SHIFT) | \
105 (blue << AD_BLUE_C_SHIFT) | (green << AD_GREEN_C_SHIFT) | \
106 (red << AD_RED_C_SHIFT) | (c3 << AD_COMP_3_SHIFT) | \
107 (c2 << AD_COMP_2_SHIFT) | (c1 << AD_COMP_1_SHIFT) | \
108 (c0 << AD_COMP_0_SHIFT) | (size << AD_PIXEL_S_SHIFT))
117 #define LAWBAR_MASK 0x00F00000
118 #define LAWBAR_SHIFT 12
120 #define LAWAR_EN 0x80000000
121 #define LAWAR_TGT_MASK 0x01F00000
122 #define LAW_TRGT_IF_LBC (0x04 << 20)
124 #define LAWAR_MASK (LAWAR_EN | LAWAR_TGT_MASK)
125 #define LAWAR_MATCH (LAWAR_EN | LAW_TRGT_IF_LBC)
127 #define BR_BA 0xFFFF8000
130 * Map a BRx value to a physical address
132 * The localbus BRx registers only store the lower 32 bits of the address. To
133 * obtain the upper four bits, we need to scan the LAW table. The entry which
134 * maps to the localbus will contain the upper four bits.
136 static phys_addr_t lbc_br_to_phys(const void *ecm, unsigned int count, u32 br)
138 #ifndef CONFIG_PHYS_64BIT
140 * If we only have 32-bit addressing, then the BRx address *is* the
145 const struct fsl_law *law = ecm + 0xc08;
148 for (i = 0; i < count; i++) {
149 u64 lawbar = in_be32(&law[i].lawbar);
150 u32 lawar = in_be32(&law[i].lawar);
152 if ((lawar & LAWAR_MASK) == LAWAR_MATCH)
153 /* Extract the upper four bits */
154 return (br & BR_BA) | ((lawbar & LAWBAR_MASK) << 12);
162 * p1022ds_set_monitor_port: switch the output to a different monitor port
164 static void p1022ds_set_monitor_port(enum fsl_diu_monitor_port port)
166 struct device_node *guts_node;
167 struct device_node *lbc_node = NULL;
168 struct device_node *law_node = NULL;
169 struct ccsr_guts __iomem *guts;
170 struct fsl_lbc_regs *lbc = NULL;
172 u8 __iomem *lbc_lcs0_ba = NULL;
173 u8 __iomem *lbc_lcs1_ba = NULL;
174 phys_addr_t cs0_addr, cs1_addr;
175 u32 br0, or0, br1, or1;
177 unsigned int num_laws;
180 /* Map the global utilities registers. */
181 guts_node = of_find_compatible_node(NULL, NULL, "fsl,p1022-guts");
183 pr_err("p1022ds: missing global utilities device node\n");
187 guts = of_iomap(guts_node, 0);
189 pr_err("p1022ds: could not map global utilities device\n");
193 lbc_node = of_find_compatible_node(NULL, NULL, "fsl,p1022-elbc");
195 pr_err("p1022ds: missing localbus node\n");
199 lbc = of_iomap(lbc_node, 0);
201 pr_err("p1022ds: could not map localbus node\n");
205 law_node = of_find_compatible_node(NULL, NULL, "fsl,ecm-law");
207 pr_err("p1022ds: missing local access window node\n");
211 ecm = of_iomap(law_node, 0);
213 pr_err("p1022ds: could not map local access window node\n");
217 iprop = of_get_property(law_node, "fsl,num-laws", NULL);
219 pr_err("p1022ds: LAW node is missing fsl,num-laws property\n");
222 num_laws = be32_to_cpup(iprop);
225 * Indirect mode requires both BR0 and BR1 to be set to "GPCM",
226 * otherwise writes to these addresses won't actually appear on the
227 * local bus, and so the PIXIS won't see them.
229 * In FCM mode, writes go to the NAND controller, which does not pass
230 * them to the localbus directly. So we force BR0 and BR1 into GPCM
231 * mode, since we don't care about what's behind the localbus any
234 br0 = in_be32(&lbc->bank[0].br);
235 br1 = in_be32(&lbc->bank[1].br);
236 or0 = in_be32(&lbc->bank[0].or);
237 or1 = in_be32(&lbc->bank[1].or);
239 /* Make sure CS0 and CS1 are programmed */
240 if (!(br0 & BR_V) || !(br1 & BR_V)) {
241 pr_err("p1022ds: CS0 and/or CS1 is not programmed\n");
246 * Use the existing BRx/ORx values if it's already GPCM. Otherwise,
247 * force the values to simple 32KB GPCM windows with the most
248 * conservative timing.
250 if ((br0 & BR_MSEL) != BR_MS_GPCM) {
251 br0 = (br0 & BR_BA) | BR_V;
252 or0 = 0xFFFF8000 | 0xFF7;
253 out_be32(&lbc->bank[0].br, br0);
254 out_be32(&lbc->bank[0].or, or0);
256 if ((br1 & BR_MSEL) != BR_MS_GPCM) {
257 br1 = (br1 & BR_BA) | BR_V;
258 or1 = 0xFFFF8000 | 0xFF7;
259 out_be32(&lbc->bank[1].br, br1);
260 out_be32(&lbc->bank[1].or, or1);
263 cs0_addr = lbc_br_to_phys(ecm, num_laws, br0);
265 pr_err("p1022ds: could not determine physical address for CS0"
266 " (BR0=%08x)\n", br0);
269 cs1_addr = lbc_br_to_phys(ecm, num_laws, br1);
271 pr_err("p1022ds: could not determine physical address for CS1"
272 " (BR1=%08x)\n", br1);
276 lbc_lcs0_ba = ioremap(cs0_addr, 1);
278 pr_err("p1022ds: could not ioremap CS0 address %llx\n",
279 (unsigned long long)cs0_addr);
282 lbc_lcs1_ba = ioremap(cs1_addr, 1);
284 pr_err("p1022ds: could not ioremap CS1 address %llx\n",
285 (unsigned long long)cs1_addr);
289 /* Make sure we're in indirect mode first. */
290 if ((in_be32(&guts->pmuxcr) & PMUXCR_ELBCDIU_MASK) !=
291 PMUXCR_ELBCDIU_DIU) {
292 struct device_node *pixis_node;
296 of_find_compatible_node(NULL, NULL, "fsl,p1022ds-fpga");
298 pr_err("p1022ds: missing pixis node\n");
302 pixis = of_iomap(pixis_node, 0);
303 of_node_put(pixis_node);
305 pr_err("p1022ds: could not map pixis registers\n");
309 /* Enable indirect PIXIS mode. */
310 setbits8(pixis + PX_CTL, PX_CTL_ALTACC);
313 /* Switch the board mux to the DIU */
314 out_8(lbc_lcs0_ba, PX_BRDCFG0); /* BRDCFG0 */
315 b = in_8(lbc_lcs1_ba);
316 b |= PX_BRDCFG0_ELBC_DIU;
317 out_8(lbc_lcs1_ba, b);
319 /* Set the chip mux to DIU mode. */
320 clrsetbits_be32(&guts->pmuxcr, PMUXCR_ELBCDIU_MASK,
322 in_be32(&guts->pmuxcr);
327 case FSL_DIU_PORT_DVI:
328 /* Enable the DVI port, disable the DFP and the backlight */
329 out_8(lbc_lcs0_ba, PX_BRDCFG1);
330 b = in_8(lbc_lcs1_ba);
331 b &= ~(PX_BRDCFG1_DFPEN | PX_BRDCFG1_BACKLIGHT);
332 b |= PX_BRDCFG1_DVIEN;
333 out_8(lbc_lcs1_ba, b);
335 case FSL_DIU_PORT_LVDS:
337 * LVDS also needs backlight enabled, otherwise the display
340 /* Enable the DFP port, disable the DVI and the backlight */
341 out_8(lbc_lcs0_ba, PX_BRDCFG1);
342 b = in_8(lbc_lcs1_ba);
343 b &= ~PX_BRDCFG1_DVIEN;
344 b |= PX_BRDCFG1_DFPEN | PX_BRDCFG1_BACKLIGHT;
345 out_8(lbc_lcs1_ba, b);
348 pr_err("p1022ds: unsupported monitor port %i\n", port);
353 iounmap(lbc_lcs1_ba);
355 iounmap(lbc_lcs0_ba);
363 of_node_put(law_node);
364 of_node_put(lbc_node);
365 of_node_put(guts_node);
369 * p1022ds_set_pixel_clock: program the DIU's clock
371 * @pixclock: the wavelength, in picoseconds, of the clock
373 void p1022ds_set_pixel_clock(unsigned int pixclock)
375 struct device_node *guts_np = NULL;
376 struct ccsr_guts __iomem *guts;
381 /* Map the global utilities registers. */
382 guts_np = of_find_compatible_node(NULL, NULL, "fsl,p1022-guts");
384 pr_err("p1022ds: missing global utilities device node\n");
388 guts = of_iomap(guts_np, 0);
389 of_node_put(guts_np);
391 pr_err("p1022ds: could not map global utilities device\n");
395 /* Convert pixclock from a wavelength to a frequency */
396 temp = 1000000000000ULL;
397 do_div(temp, pixclock);
401 * 'pxclk' is the ratio of the platform clock to the pixel clock.
402 * This number is programmed into the CLKDVDR register, and the valid
403 * range of values is 2-255.
405 pxclk = DIV_ROUND_CLOSEST(fsl_get_sys_freq(), freq);
406 pxclk = clamp_t(u32, pxclk, 2, 255);
408 /* Disable the pixel clock, and set it to non-inverted and no delay */
409 clrbits32(&guts->clkdvdr,
410 CLKDVDR_PXCKEN | CLKDVDR_PXCKDLY | CLKDVDR_PXCLK_MASK);
412 /* Enable the clock and set the pxclk */
413 setbits32(&guts->clkdvdr, CLKDVDR_PXCKEN | (pxclk << 16));
419 * p1022ds_valid_monitor_port: set the monitor port for sysfs
421 enum fsl_diu_monitor_port
422 p1022ds_valid_monitor_port(enum fsl_diu_monitor_port port)
425 case FSL_DIU_PORT_DVI:
426 case FSL_DIU_PORT_LVDS:
429 return FSL_DIU_PORT_DVI; /* Dual-link LVDS is not supported */
435 void __init p1022_ds_pic_init(void)
437 struct mpic *mpic = mpic_alloc(NULL, 0, MPIC_BIG_ENDIAN |
438 MPIC_SINGLE_DEST_CPU,
439 0, 256, " OpenPIC ");
440 BUG_ON(mpic == NULL);
444 #if defined(CONFIG_FB_FSL_DIU) || defined(CONFIG_FB_FSL_DIU_MODULE)
446 /* TRUE if there is a "video=fslfb" command-line parameter. */
450 * Search for a "video=fslfb" command-line parameter, and set 'fslfb' to
451 * true if we find it.
453 * We need to use early_param() instead of __setup() because the normal
454 * __setup() gets called to late. However, early_param() gets called very
455 * early, before the device tree is unflattened, so all we can do now is set a
456 * global variable. Later on, p1022_ds_setup_arch() will use that variable
457 * to determine if we need to update the device tree.
459 static int __init early_video_setup(char *options)
461 fslfb = (strncmp(options, "fslfb:", 6) == 0);
465 early_param("video", early_video_setup);
470 * Setup the architecture
472 static void __init p1022_ds_setup_arch(void)
475 ppc_md.progress("p1022_ds_setup_arch()", 0);
477 #if defined(CONFIG_FB_FSL_DIU) || defined(CONFIG_FB_FSL_DIU_MODULE)
478 diu_ops.set_monitor_port = p1022ds_set_monitor_port;
479 diu_ops.set_pixel_clock = p1022ds_set_pixel_clock;
480 diu_ops.valid_monitor_port = p1022ds_valid_monitor_port;
483 * Disable the NOR and NAND flash nodes if there is video=fslfb...
484 * command-line parameter. When the DIU is active, the localbus is
485 * unavailable, so we have to disable these nodes before the MTD
489 struct device_node *np =
490 of_find_compatible_node(NULL, NULL, "fsl,p1022-elbc");
493 struct device_node *np2;
496 np2 = of_find_compatible_node(np, NULL, "cfi-flash");
498 static struct property nor_status = {
501 .length = sizeof("disabled"),
505 * of_update_property() is called before
506 * kmalloc() is available, so the 'new' object
507 * should be allocated in the global area.
508 * The easiest way is to do that is to
509 * allocate one static local variable for each
510 * call to this function.
512 pr_info("p1022ds: disabling %pOF node",
514 of_update_property(np2, &nor_status);
519 np2 = of_find_compatible_node(np, NULL,
520 "fsl,elbc-fcm-nand");
522 static struct property nand_status = {
525 .length = sizeof("disabled"),
528 pr_info("p1022ds: disabling %pOF node",
530 of_update_property(np2, &nand_status);
543 fsl_pci_assign_primary();
547 pr_info("Freescale P1022 DS reference board\n");
550 machine_arch_initcall(p1022_ds, mpc85xx_common_publish_devices);
552 define_machine(p1022_ds) {
554 .compatible = "fsl,p1022ds",
555 .setup_arch = p1022_ds_setup_arch,
556 .init_IRQ = p1022_ds_pic_init,
558 .pcibios_fixup_bus = fsl_pcibios_fixup_bus,
559 .pcibios_fixup_phb = fsl_pcibios_fixup_phb,
561 .get_irq = mpic_get_irq,
562 .progress = udbg_progress,