2 * mxser.c -- MOXA Smartio/Industio family multiport serial driver.
4 * Copyright (C) 1999-2006 Moxa Technologies (support@moxa.com).
5 * Copyright (C) 2006-2008 Jiri Slaby <jirislaby@gmail.com>
7 * This code is loosely based on the 1.8 moxa driver which is based on
8 * Linux serial driver, written by Linus Torvalds, Theodore T'so and
11 * This program is free software; you can redistribute it and/or modify
12 * it under the terms of the GNU General Public License as published by
13 * the Free Software Foundation; either version 2 of the License, or
14 * (at your option) any later version.
16 * Fed through a cleanup, indent and remove of non 2.6 code by Alan Cox
17 * <alan@lxorguk.ukuu.org.uk>. The original 1.8 code is available on
19 * - Fixed x86_64 cleanness
22 #include <linux/module.h>
23 #include <linux/errno.h>
24 #include <linux/signal.h>
25 #include <linux/sched.h>
26 #include <linux/timer.h>
27 #include <linux/interrupt.h>
28 #include <linux/tty.h>
29 #include <linux/tty_flip.h>
30 #include <linux/serial.h>
31 #include <linux/serial_reg.h>
32 #include <linux/major.h>
33 #include <linux/string.h>
34 #include <linux/fcntl.h>
35 #include <linux/ptrace.h>
36 #include <linux/ioport.h>
38 #include <linux/delay.h>
39 #include <linux/pci.h>
40 #include <linux/bitops.h>
41 #include <linux/slab.h>
42 #include <linux/ratelimit.h>
46 #include <asm/uaccess.h>
50 #define MXSER_VERSION "2.0.5" /* 1.14 */
51 #define MXSERMAJOR 174
53 #define MXSER_BOARDS 4 /* Max. boards */
54 #define MXSER_PORTS_PER_BOARD 8 /* Max. ports per board */
55 #define MXSER_PORTS (MXSER_BOARDS * MXSER_PORTS_PER_BOARD)
56 #define MXSER_ISR_PASS_LIMIT 100
58 /*CheckIsMoxaMust return value*/
59 #define MOXA_OTHER_UART 0x00
60 #define MOXA_MUST_MU150_HWID 0x01
61 #define MOXA_MUST_MU860_HWID 0x02
63 #define WAKEUP_CHARS 256
65 #define UART_MCR_AFE 0x20
66 #define UART_LSR_SPECIAL 0x1E
68 #define PCI_DEVICE_ID_POS104UL 0x1044
69 #define PCI_DEVICE_ID_CB108 0x1080
70 #define PCI_DEVICE_ID_CP102UF 0x1023
71 #define PCI_DEVICE_ID_CP112UL 0x1120
72 #define PCI_DEVICE_ID_CB114 0x1142
73 #define PCI_DEVICE_ID_CP114UL 0x1143
74 #define PCI_DEVICE_ID_CB134I 0x1341
75 #define PCI_DEVICE_ID_CP138U 0x1380
78 #define C168_ASIC_ID 1
79 #define C104_ASIC_ID 2
80 #define C102_ASIC_ID 0xB
81 #define CI132_ASIC_ID 4
82 #define CI134_ASIC_ID 3
83 #define CI104J_ASIC_ID 5
85 #define MXSER_HIGHBAUD 1
88 /* This is only for PCI */
98 } Gpci_uart_info[] = {
99 {MOXA_OTHER_UART, 16, 16, 16, 14, 14, 1, 921600L},
100 {MOXA_MUST_MU150_HWID, 64, 64, 64, 48, 48, 16, 230400L},
101 {MOXA_MUST_MU860_HWID, 128, 128, 128, 96, 96, 32, 921600L}
103 #define UART_INFO_NUM ARRAY_SIZE(Gpci_uart_info)
105 struct mxser_cardinfo {
111 static const struct mxser_cardinfo mxser_cards[] = {
112 /* 0*/ { "C168 series", 8, },
113 { "C104 series", 4, },
114 { "CI-104J series", 4, },
115 { "C168H/PCI series", 8, },
116 { "C104H/PCI series", 4, },
117 /* 5*/ { "C102 series", 4, MXSER_HAS2 }, /* C102-ISA */
118 { "CI-132 series", 4, MXSER_HAS2 },
119 { "CI-134 series", 4, },
120 { "CP-132 series", 2, },
121 { "CP-114 series", 4, },
122 /*10*/ { "CT-114 series", 4, },
123 { "CP-102 series", 2, MXSER_HIGHBAUD },
124 { "CP-104U series", 4, },
125 { "CP-168U series", 8, },
126 { "CP-132U series", 2, },
127 /*15*/ { "CP-134U series", 4, },
128 { "CP-104JU series", 4, },
129 { "Moxa UC7000 Serial", 8, }, /* RC7000 */
130 { "CP-118U series", 8, },
131 { "CP-102UL series", 2, },
132 /*20*/ { "CP-102U series", 2, },
133 { "CP-118EL series", 8, },
134 { "CP-168EL series", 8, },
135 { "CP-104EL series", 4, },
136 { "CB-108 series", 8, },
137 /*25*/ { "CB-114 series", 4, },
138 { "CB-134I series", 4, },
139 { "CP-138U series", 8, },
140 { "POS-104UL series", 4, },
141 { "CP-114UL series", 4, },
142 /*30*/ { "CP-102UF series", 2, },
143 { "CP-112UL series", 2, },
146 /* driver_data correspond to the lines in the structure above
147 see also ISA probe function before you change something */
148 static struct pci_device_id mxser_pcibrds[] = {
149 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_C168), .driver_data = 3 },
150 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_C104), .driver_data = 4 },
151 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP132), .driver_data = 8 },
152 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP114), .driver_data = 9 },
153 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CT114), .driver_data = 10 },
154 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP102), .driver_data = 11 },
155 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP104U), .driver_data = 12 },
156 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP168U), .driver_data = 13 },
157 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP132U), .driver_data = 14 },
158 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP134U), .driver_data = 15 },
159 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP104JU),.driver_data = 16 },
160 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_RC7000), .driver_data = 17 },
161 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP118U), .driver_data = 18 },
162 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP102UL),.driver_data = 19 },
163 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP102U), .driver_data = 20 },
164 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP118EL),.driver_data = 21 },
165 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP168EL),.driver_data = 22 },
166 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_MOXA_CP104EL),.driver_data = 23 },
167 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CB108), .driver_data = 24 },
168 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CB114), .driver_data = 25 },
169 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CB134I), .driver_data = 26 },
170 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP138U), .driver_data = 27 },
171 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_POS104UL), .driver_data = 28 },
172 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP114UL), .driver_data = 29 },
173 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP102UF), .driver_data = 30 },
174 { PCI_VDEVICE(MOXA, PCI_DEVICE_ID_CP112UL), .driver_data = 31 },
177 MODULE_DEVICE_TABLE(pci, mxser_pcibrds);
179 static unsigned long ioaddr[MXSER_BOARDS];
180 static int ttymajor = MXSERMAJOR;
182 /* Variables for insmod */
184 MODULE_AUTHOR("Casper Yang");
185 MODULE_DESCRIPTION("MOXA Smartio/Industio Family Multiport Board Device Driver");
186 module_param_array(ioaddr, ulong, NULL, 0);
187 MODULE_PARM_DESC(ioaddr, "ISA io addresses to look for a moxa board");
188 module_param(ttymajor, int, 0);
189 MODULE_LICENSE("GPL");
193 unsigned long rxcnt[MXSER_PORTS];
194 unsigned long txcnt[MXSER_PORTS];
200 unsigned long up_rxcnt;
201 unsigned long up_txcnt;
203 unsigned char hold_reason;
206 struct mxser_mon_ext {
207 unsigned long rx_cnt[32];
208 unsigned long tx_cnt[32];
209 unsigned long up_rxcnt[32];
210 unsigned long up_txcnt[32];
211 int modem_status[32];
225 struct tty_port port;
226 struct mxser_board *board;
228 unsigned long ioaddr;
229 unsigned long opmode_ioaddr;
233 int rx_trigger; /* Rx fifo trigger level */
235 int baud_base; /* max. speed */
236 int type; /* UART type */
238 int x_char; /* xon/xoff character */
239 int IER; /* Interrupt Enable Register */
240 int MCR; /* Modem control register */
242 unsigned char stop_rx;
243 unsigned char ldisc_stop_rx;
246 unsigned char err_shadow;
248 struct async_icount icount; /* kernel counters for 4 input interrupts */
251 int read_status_mask;
252 int ignore_status_mask;
259 struct ktermios normal_termios;
261 struct mxser_mon mon_data;
269 const struct mxser_cardinfo *info;
270 unsigned long vector;
271 unsigned long vector_mask;
276 struct mxser_port ports[MXSER_PORTS_PER_BOARD];
279 struct mxser_mstatus {
287 static struct mxser_board mxser_boards[MXSER_BOARDS];
288 static struct tty_driver *mxvar_sdriver;
289 static struct mxser_log mxvar_log;
290 static int mxser_set_baud_method[MXSER_PORTS + 1];
292 static void mxser_enable_must_enchance_mode(unsigned long baseio)
297 oldlcr = inb(baseio + UART_LCR);
298 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
300 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
301 efr |= MOXA_MUST_EFR_EFRB_ENABLE;
303 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
304 outb(oldlcr, baseio + UART_LCR);
308 static void mxser_disable_must_enchance_mode(unsigned long baseio)
313 oldlcr = inb(baseio + UART_LCR);
314 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
316 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
317 efr &= ~MOXA_MUST_EFR_EFRB_ENABLE;
319 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
320 outb(oldlcr, baseio + UART_LCR);
324 static void mxser_set_must_xon1_value(unsigned long baseio, u8 value)
329 oldlcr = inb(baseio + UART_LCR);
330 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
332 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
333 efr &= ~MOXA_MUST_EFR_BANK_MASK;
334 efr |= MOXA_MUST_EFR_BANK0;
336 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
337 outb(value, baseio + MOXA_MUST_XON1_REGISTER);
338 outb(oldlcr, baseio + UART_LCR);
341 static void mxser_set_must_xoff1_value(unsigned long baseio, u8 value)
346 oldlcr = inb(baseio + UART_LCR);
347 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
349 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
350 efr &= ~MOXA_MUST_EFR_BANK_MASK;
351 efr |= MOXA_MUST_EFR_BANK0;
353 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
354 outb(value, baseio + MOXA_MUST_XOFF1_REGISTER);
355 outb(oldlcr, baseio + UART_LCR);
358 static void mxser_set_must_fifo_value(struct mxser_port *info)
363 oldlcr = inb(info->ioaddr + UART_LCR);
364 outb(MOXA_MUST_ENTER_ENCHANCE, info->ioaddr + UART_LCR);
366 efr = inb(info->ioaddr + MOXA_MUST_EFR_REGISTER);
367 efr &= ~MOXA_MUST_EFR_BANK_MASK;
368 efr |= MOXA_MUST_EFR_BANK1;
370 outb(efr, info->ioaddr + MOXA_MUST_EFR_REGISTER);
371 outb((u8)info->rx_high_water, info->ioaddr + MOXA_MUST_RBRTH_REGISTER);
372 outb((u8)info->rx_trigger, info->ioaddr + MOXA_MUST_RBRTI_REGISTER);
373 outb((u8)info->rx_low_water, info->ioaddr + MOXA_MUST_RBRTL_REGISTER);
374 outb(oldlcr, info->ioaddr + UART_LCR);
377 static void mxser_set_must_enum_value(unsigned long baseio, u8 value)
382 oldlcr = inb(baseio + UART_LCR);
383 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
385 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
386 efr &= ~MOXA_MUST_EFR_BANK_MASK;
387 efr |= MOXA_MUST_EFR_BANK2;
389 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
390 outb(value, baseio + MOXA_MUST_ENUM_REGISTER);
391 outb(oldlcr, baseio + UART_LCR);
395 static void mxser_get_must_hardware_id(unsigned long baseio, u8 *pId)
400 oldlcr = inb(baseio + UART_LCR);
401 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
403 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
404 efr &= ~MOXA_MUST_EFR_BANK_MASK;
405 efr |= MOXA_MUST_EFR_BANK2;
407 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
408 *pId = inb(baseio + MOXA_MUST_HWID_REGISTER);
409 outb(oldlcr, baseio + UART_LCR);
413 static void SET_MOXA_MUST_NO_SOFTWARE_FLOW_CONTROL(unsigned long baseio)
418 oldlcr = inb(baseio + UART_LCR);
419 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
421 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
422 efr &= ~MOXA_MUST_EFR_SF_MASK;
424 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
425 outb(oldlcr, baseio + UART_LCR);
428 static void mxser_enable_must_tx_software_flow_control(unsigned long baseio)
433 oldlcr = inb(baseio + UART_LCR);
434 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
436 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
437 efr &= ~MOXA_MUST_EFR_SF_TX_MASK;
438 efr |= MOXA_MUST_EFR_SF_TX1;
440 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
441 outb(oldlcr, baseio + UART_LCR);
444 static void mxser_disable_must_tx_software_flow_control(unsigned long baseio)
449 oldlcr = inb(baseio + UART_LCR);
450 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
452 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
453 efr &= ~MOXA_MUST_EFR_SF_TX_MASK;
455 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
456 outb(oldlcr, baseio + UART_LCR);
459 static void mxser_enable_must_rx_software_flow_control(unsigned long baseio)
464 oldlcr = inb(baseio + UART_LCR);
465 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
467 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
468 efr &= ~MOXA_MUST_EFR_SF_RX_MASK;
469 efr |= MOXA_MUST_EFR_SF_RX1;
471 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
472 outb(oldlcr, baseio + UART_LCR);
475 static void mxser_disable_must_rx_software_flow_control(unsigned long baseio)
480 oldlcr = inb(baseio + UART_LCR);
481 outb(MOXA_MUST_ENTER_ENCHANCE, baseio + UART_LCR);
483 efr = inb(baseio + MOXA_MUST_EFR_REGISTER);
484 efr &= ~MOXA_MUST_EFR_SF_RX_MASK;
486 outb(efr, baseio + MOXA_MUST_EFR_REGISTER);
487 outb(oldlcr, baseio + UART_LCR);
491 static int CheckIsMoxaMust(unsigned long io)
496 outb(0, io + UART_LCR);
497 mxser_disable_must_enchance_mode(io);
498 oldmcr = inb(io + UART_MCR);
499 outb(0, io + UART_MCR);
500 mxser_set_must_xon1_value(io, 0x11);
501 if ((hwid = inb(io + UART_MCR)) != 0) {
502 outb(oldmcr, io + UART_MCR);
503 return MOXA_OTHER_UART;
506 mxser_get_must_hardware_id(io, &hwid);
507 for (i = 1; i < UART_INFO_NUM; i++) { /* 0 = OTHER_UART */
508 if (hwid == Gpci_uart_info[i].type)
511 return MOXA_OTHER_UART;
515 static void process_txrx_fifo(struct mxser_port *info)
519 if ((info->type == PORT_16450) || (info->type == PORT_8250)) {
520 info->rx_trigger = 1;
521 info->rx_high_water = 1;
522 info->rx_low_water = 1;
523 info->xmit_fifo_size = 1;
525 for (i = 0; i < UART_INFO_NUM; i++)
526 if (info->board->chip_flag == Gpci_uart_info[i].type) {
527 info->rx_trigger = Gpci_uart_info[i].rx_trigger;
528 info->rx_low_water = Gpci_uart_info[i].rx_low_water;
529 info->rx_high_water = Gpci_uart_info[i].rx_high_water;
530 info->xmit_fifo_size = Gpci_uart_info[i].xmit_fifo_size;
535 static unsigned char mxser_get_msr(int baseaddr, int mode, int port)
537 static unsigned char mxser_msr[MXSER_PORTS + 1];
538 unsigned char status = 0;
540 status = inb(baseaddr + UART_MSR);
542 mxser_msr[port] &= 0x0F;
543 mxser_msr[port] |= status;
544 status = mxser_msr[port];
551 static int mxser_carrier_raised(struct tty_port *port)
553 struct mxser_port *mp = container_of(port, struct mxser_port, port);
554 return (inb(mp->ioaddr + UART_MSR) & UART_MSR_DCD)?1:0;
557 static void mxser_dtr_rts(struct tty_port *port, int on)
559 struct mxser_port *mp = container_of(port, struct mxser_port, port);
562 spin_lock_irqsave(&mp->slock, flags);
564 outb(inb(mp->ioaddr + UART_MCR) |
565 UART_MCR_DTR | UART_MCR_RTS, mp->ioaddr + UART_MCR);
567 outb(inb(mp->ioaddr + UART_MCR)&~(UART_MCR_DTR | UART_MCR_RTS),
568 mp->ioaddr + UART_MCR);
569 spin_unlock_irqrestore(&mp->slock, flags);
572 static int mxser_set_baud(struct tty_struct *tty, long newspd)
574 struct mxser_port *info = tty->driver_data;
581 if (newspd > info->max_baud)
585 quot = 2 * info->baud_base / 269;
586 tty_encode_baud_rate(tty, 134, 134);
588 quot = info->baud_base / newspd;
591 baud = info->baud_base/quot;
592 tty_encode_baud_rate(tty, baud, baud);
597 info->timeout = ((info->xmit_fifo_size * HZ * 10 * quot) / info->baud_base);
598 info->timeout += HZ / 50; /* Add .02 seconds of slop */
601 info->MCR |= UART_MCR_DTR;
602 outb(info->MCR, info->ioaddr + UART_MCR);
604 info->MCR &= ~UART_MCR_DTR;
605 outb(info->MCR, info->ioaddr + UART_MCR);
609 cval = inb(info->ioaddr + UART_LCR);
611 outb(cval | UART_LCR_DLAB, info->ioaddr + UART_LCR); /* set DLAB */
613 outb(quot & 0xff, info->ioaddr + UART_DLL); /* LS of divisor */
614 outb(quot >> 8, info->ioaddr + UART_DLM); /* MS of divisor */
615 outb(cval, info->ioaddr + UART_LCR); /* reset DLAB */
618 if (C_BAUD(tty) == BOTHER) {
619 quot = info->baud_base % newspd;
621 if (quot % newspd > newspd / 2) {
627 mxser_set_must_enum_value(info->ioaddr, quot);
630 mxser_set_must_enum_value(info->ioaddr, 0);
636 * This routine is called to set the UART divisor registers to match
637 * the specified baud rate for a serial port.
639 static int mxser_change_speed(struct tty_struct *tty,
640 struct ktermios *old_termios)
642 struct mxser_port *info = tty->driver_data;
643 unsigned cflag, cval, fcr;
645 unsigned char status;
647 cflag = tty->termios.c_cflag;
651 if (mxser_set_baud_method[tty->index] == 0)
652 mxser_set_baud(tty, tty_get_baud_rate(tty));
654 /* byte size and parity */
655 switch (cflag & CSIZE) {
670 break; /* too keep GCC shut... */
675 cval |= UART_LCR_PARITY;
676 if (!(cflag & PARODD))
677 cval |= UART_LCR_EPAR;
679 cval |= UART_LCR_SPAR;
681 if ((info->type == PORT_8250) || (info->type == PORT_16450)) {
682 if (info->board->chip_flag) {
683 fcr = UART_FCR_ENABLE_FIFO;
684 fcr |= MOXA_MUST_FCR_GDA_MODE_ENABLE;
685 mxser_set_must_fifo_value(info);
689 fcr = UART_FCR_ENABLE_FIFO;
690 if (info->board->chip_flag) {
691 fcr |= MOXA_MUST_FCR_GDA_MODE_ENABLE;
692 mxser_set_must_fifo_value(info);
694 switch (info->rx_trigger) {
696 fcr |= UART_FCR_TRIGGER_1;
699 fcr |= UART_FCR_TRIGGER_4;
702 fcr |= UART_FCR_TRIGGER_8;
705 fcr |= UART_FCR_TRIGGER_14;
711 /* CTS flow control flag and modem status interrupts */
712 info->IER &= ~UART_IER_MSI;
713 info->MCR &= ~UART_MCR_AFE;
714 tty_port_set_cts_flow(&info->port, cflag & CRTSCTS);
715 if (cflag & CRTSCTS) {
716 info->IER |= UART_IER_MSI;
717 if ((info->type == PORT_16550A) || (info->board->chip_flag)) {
718 info->MCR |= UART_MCR_AFE;
720 status = inb(info->ioaddr + UART_MSR);
721 if (tty->hw_stopped) {
722 if (status & UART_MSR_CTS) {
724 if (info->type != PORT_16550A &&
725 !info->board->chip_flag) {
726 outb(info->IER & ~UART_IER_THRI,
729 info->IER |= UART_IER_THRI;
730 outb(info->IER, info->ioaddr +
736 if (!(status & UART_MSR_CTS)) {
738 if ((info->type != PORT_16550A) &&
739 (!info->board->chip_flag)) {
740 info->IER &= ~UART_IER_THRI;
741 outb(info->IER, info->ioaddr +
748 outb(info->MCR, info->ioaddr + UART_MCR);
749 tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL);
751 info->IER |= UART_IER_MSI;
752 outb(info->IER, info->ioaddr + UART_IER);
755 * Set up parity check flag
757 info->read_status_mask = UART_LSR_OE | UART_LSR_THRE | UART_LSR_DR;
759 info->read_status_mask |= UART_LSR_FE | UART_LSR_PE;
760 if (I_BRKINT(tty) || I_PARMRK(tty))
761 info->read_status_mask |= UART_LSR_BI;
763 info->ignore_status_mask = 0;
766 info->ignore_status_mask |= UART_LSR_BI;
767 info->read_status_mask |= UART_LSR_BI;
769 * If we're ignore parity and break indicators, ignore
770 * overruns too. (For real raw support).
773 info->ignore_status_mask |=
777 info->read_status_mask |=
783 if (info->board->chip_flag) {
784 mxser_set_must_xon1_value(info->ioaddr, START_CHAR(tty));
785 mxser_set_must_xoff1_value(info->ioaddr, STOP_CHAR(tty));
787 mxser_enable_must_rx_software_flow_control(
790 mxser_disable_must_rx_software_flow_control(
794 mxser_enable_must_tx_software_flow_control(
797 mxser_disable_must_tx_software_flow_control(
803 outb(fcr, info->ioaddr + UART_FCR); /* set fcr */
804 outb(cval, info->ioaddr + UART_LCR);
809 static void mxser_check_modem_status(struct tty_struct *tty,
810 struct mxser_port *port, int status)
812 /* update input line counters */
813 if (status & UART_MSR_TERI)
815 if (status & UART_MSR_DDSR)
817 if (status & UART_MSR_DDCD)
819 if (status & UART_MSR_DCTS)
821 port->mon_data.modem_status = status;
822 wake_up_interruptible(&port->port.delta_msr_wait);
824 if (tty_port_check_carrier(&port->port) && (status & UART_MSR_DDCD)) {
825 if (status & UART_MSR_DCD)
826 wake_up_interruptible(&port->port.open_wait);
829 if (tty_port_cts_enabled(&port->port)) {
830 if (tty->hw_stopped) {
831 if (status & UART_MSR_CTS) {
834 if ((port->type != PORT_16550A) &&
835 (!port->board->chip_flag)) {
836 outb(port->IER & ~UART_IER_THRI,
837 port->ioaddr + UART_IER);
838 port->IER |= UART_IER_THRI;
839 outb(port->IER, port->ioaddr +
845 if (!(status & UART_MSR_CTS)) {
847 if (port->type != PORT_16550A &&
848 !port->board->chip_flag) {
849 port->IER &= ~UART_IER_THRI;
850 outb(port->IER, port->ioaddr +
858 static int mxser_activate(struct tty_port *port, struct tty_struct *tty)
860 struct mxser_port *info = container_of(port, struct mxser_port, port);
865 page = __get_free_page(GFP_KERNEL);
869 spin_lock_irqsave(&info->slock, flags);
871 if (!info->ioaddr || !info->type) {
872 set_bit(TTY_IO_ERROR, &tty->flags);
873 spin_unlock_irqrestore(&info->slock, flags);
877 info->port.xmit_buf = (unsigned char *) page;
880 * Clear the FIFO buffers and disable them
881 * (they will be reenabled in mxser_change_speed())
883 if (info->board->chip_flag)
884 outb((UART_FCR_CLEAR_RCVR |
885 UART_FCR_CLEAR_XMIT |
886 MOXA_MUST_FCR_GDA_MODE_ENABLE), info->ioaddr + UART_FCR);
888 outb((UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT),
889 info->ioaddr + UART_FCR);
892 * At this point there's no way the LSR could still be 0xFF;
893 * if it is, then bail out, because there's likely no UART
896 if (inb(info->ioaddr + UART_LSR) == 0xff) {
897 spin_unlock_irqrestore(&info->slock, flags);
898 if (capable(CAP_SYS_ADMIN)) {
899 set_bit(TTY_IO_ERROR, &tty->flags);
908 * Clear the interrupt registers.
910 (void) inb(info->ioaddr + UART_LSR);
911 (void) inb(info->ioaddr + UART_RX);
912 (void) inb(info->ioaddr + UART_IIR);
913 (void) inb(info->ioaddr + UART_MSR);
916 * Now, initialize the UART
918 outb(UART_LCR_WLEN8, info->ioaddr + UART_LCR); /* reset DLAB */
919 info->MCR = UART_MCR_DTR | UART_MCR_RTS;
920 outb(info->MCR, info->ioaddr + UART_MCR);
923 * Finally, enable interrupts
925 info->IER = UART_IER_MSI | UART_IER_RLSI | UART_IER_RDI;
927 if (info->board->chip_flag)
928 info->IER |= MOXA_MUST_IER_EGDAI;
929 outb(info->IER, info->ioaddr + UART_IER); /* enable interrupts */
932 * And clear the interrupt registers again for luck.
934 (void) inb(info->ioaddr + UART_LSR);
935 (void) inb(info->ioaddr + UART_RX);
936 (void) inb(info->ioaddr + UART_IIR);
937 (void) inb(info->ioaddr + UART_MSR);
939 clear_bit(TTY_IO_ERROR, &tty->flags);
940 info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
943 * and set the speed of the serial port
945 mxser_change_speed(tty, NULL);
946 spin_unlock_irqrestore(&info->slock, flags);
951 info->port.xmit_buf = NULL;
956 * This routine will shutdown a serial port
958 static void mxser_shutdown_port(struct tty_port *port)
960 struct mxser_port *info = container_of(port, struct mxser_port, port);
963 spin_lock_irqsave(&info->slock, flags);
966 * clear delta_msr_wait queue to avoid mem leaks: we may free the irq
967 * here so the queue might never be waken up
969 wake_up_interruptible(&info->port.delta_msr_wait);
972 * Free the xmit buffer, if necessary
974 if (info->port.xmit_buf) {
975 free_page((unsigned long) info->port.xmit_buf);
976 info->port.xmit_buf = NULL;
980 outb(0x00, info->ioaddr + UART_IER);
982 /* clear Rx/Tx FIFO's */
983 if (info->board->chip_flag)
984 outb(UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT |
985 MOXA_MUST_FCR_GDA_MODE_ENABLE,
986 info->ioaddr + UART_FCR);
988 outb(UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT,
989 info->ioaddr + UART_FCR);
991 /* read data port to reset things */
992 (void) inb(info->ioaddr + UART_RX);
995 if (info->board->chip_flag)
996 SET_MOXA_MUST_NO_SOFTWARE_FLOW_CONTROL(info->ioaddr);
998 spin_unlock_irqrestore(&info->slock, flags);
1002 * This routine is called whenever a serial port is opened. It
1003 * enables interrupts for a serial port, linking in its async structure into
1004 * the IRQ chain. It also performs the serial-specific
1005 * initialization for the tty structure.
1007 static int mxser_open(struct tty_struct *tty, struct file *filp)
1009 struct mxser_port *info;
1013 if (line == MXSER_PORTS)
1015 info = &mxser_boards[line / MXSER_PORTS_PER_BOARD].ports[line % MXSER_PORTS_PER_BOARD];
1019 tty->driver_data = info;
1020 return tty_port_open(&info->port, tty, filp);
1023 static void mxser_flush_buffer(struct tty_struct *tty)
1025 struct mxser_port *info = tty->driver_data;
1027 unsigned long flags;
1030 spin_lock_irqsave(&info->slock, flags);
1031 info->xmit_cnt = info->xmit_head = info->xmit_tail = 0;
1033 fcr = inb(info->ioaddr + UART_FCR);
1034 outb((fcr | UART_FCR_CLEAR_RCVR | UART_FCR_CLEAR_XMIT),
1035 info->ioaddr + UART_FCR);
1036 outb(fcr, info->ioaddr + UART_FCR);
1038 spin_unlock_irqrestore(&info->slock, flags);
1044 static void mxser_close_port(struct tty_port *port)
1046 struct mxser_port *info = container_of(port, struct mxser_port, port);
1047 unsigned long timeout;
1049 * At this point we stop accepting input. To do this, we
1050 * disable the receive line status interrupts, and tell the
1051 * interrupt driver to stop checking the data ready bit in the
1052 * line status register.
1054 info->IER &= ~UART_IER_RLSI;
1055 if (info->board->chip_flag)
1056 info->IER &= ~MOXA_MUST_RECV_ISR;
1058 outb(info->IER, info->ioaddr + UART_IER);
1060 * Before we drop DTR, make sure the UART transmitter
1061 * has completely drained; this is especially
1062 * important if there is a transmit FIFO!
1064 timeout = jiffies + HZ;
1065 while (!(inb(info->ioaddr + UART_LSR) & UART_LSR_TEMT)) {
1066 schedule_timeout_interruptible(5);
1067 if (time_after(jiffies, timeout))
1073 * This routine is called when the serial port gets closed. First, we
1074 * wait for the last remaining data to be sent. Then, we unlink its
1075 * async structure from the interrupt chain if necessary, and we free
1076 * that IRQ if nothing is left in the chain.
1078 static void mxser_close(struct tty_struct *tty, struct file *filp)
1080 struct mxser_port *info = tty->driver_data;
1081 struct tty_port *port = &info->port;
1083 if (tty->index == MXSER_PORTS || info == NULL)
1085 if (tty_port_close_start(port, tty, filp) == 0)
1088 mutex_lock(&port->mutex);
1089 mxser_close_port(port);
1090 mxser_flush_buffer(tty);
1091 if (tty_port_initialized(port) && C_HUPCL(tty))
1092 tty_port_lower_dtr_rts(port);
1093 mxser_shutdown_port(port);
1094 tty_port_set_initialized(port, 0);
1095 mutex_unlock(&port->mutex);
1097 /* Right now the tty_port set is done outside of the close_end helper
1098 as we don't yet have everyone using refcounts */
1099 tty_port_close_end(port, tty);
1100 tty_port_tty_set(port, NULL);
1103 static int mxser_write(struct tty_struct *tty, const unsigned char *buf, int count)
1106 struct mxser_port *info = tty->driver_data;
1107 unsigned long flags;
1109 if (!info->port.xmit_buf)
1113 c = min_t(int, count, min(SERIAL_XMIT_SIZE - info->xmit_cnt - 1,
1114 SERIAL_XMIT_SIZE - info->xmit_head));
1118 memcpy(info->port.xmit_buf + info->xmit_head, buf, c);
1119 spin_lock_irqsave(&info->slock, flags);
1120 info->xmit_head = (info->xmit_head + c) &
1121 (SERIAL_XMIT_SIZE - 1);
1122 info->xmit_cnt += c;
1123 spin_unlock_irqrestore(&info->slock, flags);
1130 if (info->xmit_cnt && !tty->stopped) {
1131 if (!tty->hw_stopped ||
1132 (info->type == PORT_16550A) ||
1133 (info->board->chip_flag)) {
1134 spin_lock_irqsave(&info->slock, flags);
1135 outb(info->IER & ~UART_IER_THRI, info->ioaddr +
1137 info->IER |= UART_IER_THRI;
1138 outb(info->IER, info->ioaddr + UART_IER);
1139 spin_unlock_irqrestore(&info->slock, flags);
1145 static int mxser_put_char(struct tty_struct *tty, unsigned char ch)
1147 struct mxser_port *info = tty->driver_data;
1148 unsigned long flags;
1150 if (!info->port.xmit_buf)
1153 if (info->xmit_cnt >= SERIAL_XMIT_SIZE - 1)
1156 spin_lock_irqsave(&info->slock, flags);
1157 info->port.xmit_buf[info->xmit_head++] = ch;
1158 info->xmit_head &= SERIAL_XMIT_SIZE - 1;
1160 spin_unlock_irqrestore(&info->slock, flags);
1161 if (!tty->stopped) {
1162 if (!tty->hw_stopped ||
1163 (info->type == PORT_16550A) ||
1164 info->board->chip_flag) {
1165 spin_lock_irqsave(&info->slock, flags);
1166 outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER);
1167 info->IER |= UART_IER_THRI;
1168 outb(info->IER, info->ioaddr + UART_IER);
1169 spin_unlock_irqrestore(&info->slock, flags);
1176 static void mxser_flush_chars(struct tty_struct *tty)
1178 struct mxser_port *info = tty->driver_data;
1179 unsigned long flags;
1181 if (info->xmit_cnt <= 0 || tty->stopped || !info->port.xmit_buf ||
1182 (tty->hw_stopped && info->type != PORT_16550A &&
1183 !info->board->chip_flag))
1186 spin_lock_irqsave(&info->slock, flags);
1188 outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER);
1189 info->IER |= UART_IER_THRI;
1190 outb(info->IER, info->ioaddr + UART_IER);
1192 spin_unlock_irqrestore(&info->slock, flags);
1195 static int mxser_write_room(struct tty_struct *tty)
1197 struct mxser_port *info = tty->driver_data;
1200 ret = SERIAL_XMIT_SIZE - info->xmit_cnt - 1;
1201 return ret < 0 ? 0 : ret;
1204 static int mxser_chars_in_buffer(struct tty_struct *tty)
1206 struct mxser_port *info = tty->driver_data;
1207 return info->xmit_cnt;
1211 * ------------------------------------------------------------
1212 * friends of mxser_ioctl()
1213 * ------------------------------------------------------------
1215 static int mxser_get_serial_info(struct tty_struct *tty,
1216 struct serial_struct __user *retinfo)
1218 struct mxser_port *info = tty->driver_data;
1219 struct serial_struct tmp = {
1222 .port = info->ioaddr,
1223 .irq = info->board->irq,
1224 .flags = info->port.flags,
1225 .baud_base = info->baud_base,
1226 .close_delay = info->port.close_delay,
1227 .closing_wait = info->port.closing_wait,
1228 .custom_divisor = info->custom_divisor,
1230 if (copy_to_user(retinfo, &tmp, sizeof(*retinfo)))
1235 static int mxser_set_serial_info(struct tty_struct *tty,
1236 struct serial_struct __user *new_info)
1238 struct mxser_port *info = tty->driver_data;
1239 struct tty_port *port = &info->port;
1240 struct serial_struct new_serial;
1242 unsigned long sl_flags;
1246 if (!new_info || !info->ioaddr)
1248 if (copy_from_user(&new_serial, new_info, sizeof(new_serial)))
1251 if (new_serial.irq != info->board->irq ||
1252 new_serial.port != info->ioaddr)
1255 flags = port->flags & ASYNC_SPD_MASK;
1257 if (!capable(CAP_SYS_ADMIN)) {
1258 if ((new_serial.baud_base != info->baud_base) ||
1259 (new_serial.close_delay != info->port.close_delay) ||
1260 ((new_serial.flags & ~ASYNC_USR_MASK) != (info->port.flags & ~ASYNC_USR_MASK)))
1262 info->port.flags = ((info->port.flags & ~ASYNC_USR_MASK) |
1263 (new_serial.flags & ASYNC_USR_MASK));
1266 * OK, past this point, all the error checking has been done.
1267 * At this point, we start making changes.....
1269 port->flags = ((port->flags & ~ASYNC_FLAGS) |
1270 (new_serial.flags & ASYNC_FLAGS));
1271 port->close_delay = new_serial.close_delay * HZ / 100;
1272 port->closing_wait = new_serial.closing_wait * HZ / 100;
1273 port->low_latency = (port->flags & ASYNC_LOW_LATENCY) ? 1 : 0;
1274 if ((port->flags & ASYNC_SPD_MASK) == ASYNC_SPD_CUST &&
1275 (new_serial.baud_base != info->baud_base ||
1276 new_serial.custom_divisor !=
1277 info->custom_divisor)) {
1278 if (new_serial.custom_divisor == 0)
1280 baud = new_serial.baud_base / new_serial.custom_divisor;
1281 tty_encode_baud_rate(tty, baud, baud);
1285 info->type = new_serial.type;
1287 process_txrx_fifo(info);
1289 if (tty_port_initialized(port)) {
1290 if (flags != (port->flags & ASYNC_SPD_MASK)) {
1291 spin_lock_irqsave(&info->slock, sl_flags);
1292 mxser_change_speed(tty, NULL);
1293 spin_unlock_irqrestore(&info->slock, sl_flags);
1296 retval = mxser_activate(port, tty);
1298 tty_port_set_initialized(port, 1);
1304 * mxser_get_lsr_info - get line status register info
1306 * Purpose: Let user call ioctl() to get info when the UART physically
1307 * is emptied. On bus types like RS485, the transmitter must
1308 * release the bus after transmitting. This must be done when
1309 * the transmit shift register is empty, not be done when the
1310 * transmit holding register is empty. This functionality
1311 * allows an RS485 driver to be written in user space.
1313 static int mxser_get_lsr_info(struct mxser_port *info,
1314 unsigned int __user *value)
1316 unsigned char status;
1317 unsigned int result;
1318 unsigned long flags;
1320 spin_lock_irqsave(&info->slock, flags);
1321 status = inb(info->ioaddr + UART_LSR);
1322 spin_unlock_irqrestore(&info->slock, flags);
1323 result = ((status & UART_LSR_TEMT) ? TIOCSER_TEMT : 0);
1324 return put_user(result, value);
1327 static int mxser_tiocmget(struct tty_struct *tty)
1329 struct mxser_port *info = tty->driver_data;
1330 unsigned char control, status;
1331 unsigned long flags;
1334 if (tty->index == MXSER_PORTS)
1335 return -ENOIOCTLCMD;
1336 if (tty_io_error(tty))
1339 control = info->MCR;
1341 spin_lock_irqsave(&info->slock, flags);
1342 status = inb(info->ioaddr + UART_MSR);
1343 if (status & UART_MSR_ANY_DELTA)
1344 mxser_check_modem_status(tty, info, status);
1345 spin_unlock_irqrestore(&info->slock, flags);
1346 return ((control & UART_MCR_RTS) ? TIOCM_RTS : 0) |
1347 ((control & UART_MCR_DTR) ? TIOCM_DTR : 0) |
1348 ((status & UART_MSR_DCD) ? TIOCM_CAR : 0) |
1349 ((status & UART_MSR_RI) ? TIOCM_RNG : 0) |
1350 ((status & UART_MSR_DSR) ? TIOCM_DSR : 0) |
1351 ((status & UART_MSR_CTS) ? TIOCM_CTS : 0);
1354 static int mxser_tiocmset(struct tty_struct *tty,
1355 unsigned int set, unsigned int clear)
1357 struct mxser_port *info = tty->driver_data;
1358 unsigned long flags;
1361 if (tty->index == MXSER_PORTS)
1362 return -ENOIOCTLCMD;
1363 if (tty_io_error(tty))
1366 spin_lock_irqsave(&info->slock, flags);
1368 if (set & TIOCM_RTS)
1369 info->MCR |= UART_MCR_RTS;
1370 if (set & TIOCM_DTR)
1371 info->MCR |= UART_MCR_DTR;
1373 if (clear & TIOCM_RTS)
1374 info->MCR &= ~UART_MCR_RTS;
1375 if (clear & TIOCM_DTR)
1376 info->MCR &= ~UART_MCR_DTR;
1378 outb(info->MCR, info->ioaddr + UART_MCR);
1379 spin_unlock_irqrestore(&info->slock, flags);
1383 static int __init mxser_program_mode(int port)
1395 id = inb(port + 1) & 0x1F;
1396 if ((id != C168_ASIC_ID) &&
1397 (id != C104_ASIC_ID) &&
1398 (id != C102_ASIC_ID) &&
1399 (id != CI132_ASIC_ID) &&
1400 (id != CI134_ASIC_ID) &&
1401 (id != CI104J_ASIC_ID))
1403 for (i = 0, j = 0; i < 4; i++) {
1407 } else if ((j == 1) && (n == 1)) {
1418 static void __init mxser_normal_mode(int port)
1422 outb(0xA5, port + 1);
1423 outb(0x80, port + 3);
1424 outb(12, port + 0); /* 9600 bps */
1426 outb(0x03, port + 3); /* 8 data bits */
1427 outb(0x13, port + 4); /* loop back mode */
1428 for (i = 0; i < 16; i++) {
1430 if ((n & 0x61) == 0x60)
1435 outb(0x00, port + 4);
1438 #define CHIP_SK 0x01 /* Serial Data Clock in Eprom */
1439 #define CHIP_DO 0x02 /* Serial Data Output in Eprom */
1440 #define CHIP_CS 0x04 /* Serial Chip Select in Eprom */
1441 #define CHIP_DI 0x08 /* Serial Data Input in Eprom */
1442 #define EN_CCMD 0x000 /* Chip's command register */
1443 #define EN0_RSARLO 0x008 /* Remote start address reg 0 */
1444 #define EN0_RSARHI 0x009 /* Remote start address reg 1 */
1445 #define EN0_RCNTLO 0x00A /* Remote byte count reg WR */
1446 #define EN0_RCNTHI 0x00B /* Remote byte count reg WR */
1447 #define EN0_DCFG 0x00E /* Data configuration reg WR */
1448 #define EN0_PORT 0x010 /* Rcv missed frame error counter RD */
1449 #define ENC_PAGE0 0x000 /* Select page 0 of chip registers */
1450 #define ENC_PAGE3 0x0C0 /* Select page 3 of chip registers */
1451 static int __init mxser_read_register(int port, unsigned short *regs)
1453 int i, k, value, id;
1456 id = mxser_program_mode(port);
1459 for (i = 0; i < 14; i++) {
1460 k = (i & 0x3F) | 0x180;
1461 for (j = 0x100; j > 0; j >>= 1) {
1462 outb(CHIP_CS, port);
1464 outb(CHIP_CS | CHIP_DO, port);
1465 outb(CHIP_CS | CHIP_DO | CHIP_SK, port); /* A? bit of read */
1467 outb(CHIP_CS, port);
1468 outb(CHIP_CS | CHIP_SK, port); /* A? bit of read */
1473 for (k = 0, j = 0x8000; k < 16; k++, j >>= 1) {
1474 outb(CHIP_CS, port);
1475 outb(CHIP_CS | CHIP_SK, port);
1476 if (inb(port) & CHIP_DI)
1482 mxser_normal_mode(port);
1486 static int mxser_ioctl_special(unsigned int cmd, void __user *argp)
1488 struct mxser_port *ip;
1489 struct tty_port *port;
1490 struct tty_struct *tty;
1496 case MOXA_GET_MAJOR:
1497 printk_ratelimited(KERN_WARNING "mxser: '%s' uses deprecated ioctl "
1498 "%x (GET_MAJOR), fix your userspace\n",
1499 current->comm, cmd);
1500 return put_user(ttymajor, (int __user *)argp);
1502 case MOXA_CHKPORTENABLE:
1504 for (i = 0; i < MXSER_BOARDS; i++)
1505 for (j = 0; j < MXSER_PORTS_PER_BOARD; j++)
1506 if (mxser_boards[i].ports[j].ioaddr)
1508 return put_user(result, (unsigned long __user *)argp);
1509 case MOXA_GETDATACOUNT:
1510 /* The receive side is locked by port->slock but it isn't
1511 clear that an exact snapshot is worth copying here */
1512 if (copy_to_user(argp, &mxvar_log, sizeof(mxvar_log)))
1515 case MOXA_GETMSTATUS: {
1516 struct mxser_mstatus ms, __user *msu = argp;
1517 for (i = 0; i < MXSER_BOARDS; i++)
1518 for (j = 0; j < MXSER_PORTS_PER_BOARD; j++) {
1519 ip = &mxser_boards[i].ports[j];
1521 memset(&ms, 0, sizeof(ms));
1523 mutex_lock(&port->mutex);
1527 tty = tty_port_tty_get(port);
1530 ms.cflag = ip->normal_termios.c_cflag;
1532 ms.cflag = tty->termios.c_cflag;
1534 spin_lock_irq(&ip->slock);
1535 status = inb(ip->ioaddr + UART_MSR);
1536 spin_unlock_irq(&ip->slock);
1537 if (status & UART_MSR_DCD)
1539 if (status & UART_MSR_DSR)
1541 if (status & UART_MSR_CTS)
1544 mutex_unlock(&port->mutex);
1545 if (copy_to_user(msu, &ms, sizeof(ms)))
1551 case MOXA_ASPP_MON_EXT: {
1552 struct mxser_mon_ext *me; /* it's 2k, stack unfriendly */
1553 unsigned int cflag, iflag, p;
1556 me = kzalloc(sizeof(*me), GFP_KERNEL);
1560 for (i = 0, p = 0; i < MXSER_BOARDS; i++) {
1561 for (j = 0; j < MXSER_PORTS_PER_BOARD; j++, p++) {
1562 if (p >= ARRAY_SIZE(me->rx_cnt)) {
1566 ip = &mxser_boards[i].ports[j];
1569 mutex_lock(&port->mutex);
1571 mutex_unlock(&port->mutex);
1575 spin_lock_irq(&ip->slock);
1576 status = mxser_get_msr(ip->ioaddr, 0, p);
1578 if (status & UART_MSR_TERI)
1580 if (status & UART_MSR_DDSR)
1582 if (status & UART_MSR_DDCD)
1584 if (status & UART_MSR_DCTS)
1587 ip->mon_data.modem_status = status;
1588 me->rx_cnt[p] = ip->mon_data.rxcnt;
1589 me->tx_cnt[p] = ip->mon_data.txcnt;
1590 me->up_rxcnt[p] = ip->mon_data.up_rxcnt;
1591 me->up_txcnt[p] = ip->mon_data.up_txcnt;
1592 me->modem_status[p] =
1593 ip->mon_data.modem_status;
1594 spin_unlock_irq(&ip->slock);
1596 tty = tty_port_tty_get(&ip->port);
1599 cflag = ip->normal_termios.c_cflag;
1600 iflag = ip->normal_termios.c_iflag;
1601 me->baudrate[p] = tty_termios_baud_rate(&ip->normal_termios);
1603 cflag = tty->termios.c_cflag;
1604 iflag = tty->termios.c_iflag;
1605 me->baudrate[p] = tty_get_baud_rate(tty);
1609 me->databits[p] = cflag & CSIZE;
1610 me->stopbits[p] = cflag & CSTOPB;
1611 me->parity[p] = cflag & (PARENB | PARODD |
1614 if (cflag & CRTSCTS)
1615 me->flowctrl[p] |= 0x03;
1617 if (iflag & (IXON | IXOFF))
1618 me->flowctrl[p] |= 0x0C;
1620 if (ip->type == PORT_16550A)
1623 if (ip->board->chip_flag == MOXA_MUST_MU860_HWID) {
1624 opmode = inb(ip->opmode_ioaddr)>>((p % 4) * 2);
1625 opmode &= OP_MODE_MASK;
1627 opmode = RS232_MODE;
1629 me->iftype[p] = opmode;
1630 mutex_unlock(&port->mutex);
1633 if (copy_to_user(argp, me, sizeof(*me)))
1639 return -ENOIOCTLCMD;
1644 static int mxser_cflags_changed(struct mxser_port *info, unsigned long arg,
1645 struct async_icount *cprev)
1647 struct async_icount cnow;
1648 unsigned long flags;
1651 spin_lock_irqsave(&info->slock, flags);
1652 cnow = info->icount; /* atomic copy */
1653 spin_unlock_irqrestore(&info->slock, flags);
1655 ret = ((arg & TIOCM_RNG) && (cnow.rng != cprev->rng)) ||
1656 ((arg & TIOCM_DSR) && (cnow.dsr != cprev->dsr)) ||
1657 ((arg & TIOCM_CD) && (cnow.dcd != cprev->dcd)) ||
1658 ((arg & TIOCM_CTS) && (cnow.cts != cprev->cts));
1665 static int mxser_ioctl(struct tty_struct *tty,
1666 unsigned int cmd, unsigned long arg)
1668 struct mxser_port *info = tty->driver_data;
1669 struct tty_port *port = &info->port;
1670 struct async_icount cnow;
1671 unsigned long flags;
1672 void __user *argp = (void __user *)arg;
1675 if (tty->index == MXSER_PORTS)
1676 return mxser_ioctl_special(cmd, argp);
1678 if (cmd == MOXA_SET_OP_MODE || cmd == MOXA_GET_OP_MODE) {
1680 unsigned long opmode;
1681 static unsigned char ModeMask[] = { 0xfc, 0xf3, 0xcf, 0x3f };
1683 unsigned char val, mask;
1685 if (info->board->chip_flag != MOXA_MUST_MU860_HWID)
1689 if (cmd == MOXA_SET_OP_MODE) {
1690 if (get_user(opmode, (int __user *) argp))
1692 if (opmode != RS232_MODE &&
1693 opmode != RS485_2WIRE_MODE &&
1694 opmode != RS422_MODE &&
1695 opmode != RS485_4WIRE_MODE)
1699 spin_lock_irq(&info->slock);
1700 val = inb(info->opmode_ioaddr);
1702 val |= (opmode << shiftbit);
1703 outb(val, info->opmode_ioaddr);
1704 spin_unlock_irq(&info->slock);
1707 spin_lock_irq(&info->slock);
1708 opmode = inb(info->opmode_ioaddr) >> shiftbit;
1709 spin_unlock_irq(&info->slock);
1710 opmode &= OP_MODE_MASK;
1711 if (put_user(opmode, (int __user *)argp))
1717 if (cmd != TIOCGSERIAL && cmd != TIOCMIWAIT && tty_io_error(tty))
1722 mutex_lock(&port->mutex);
1723 retval = mxser_get_serial_info(tty, argp);
1724 mutex_unlock(&port->mutex);
1727 mutex_lock(&port->mutex);
1728 retval = mxser_set_serial_info(tty, argp);
1729 mutex_unlock(&port->mutex);
1731 case TIOCSERGETLSR: /* Get line status register */
1732 return mxser_get_lsr_info(info, argp);
1734 * Wait for any of the 4 modem inputs (DCD,RI,DSR,CTS) to change
1735 * - mask passed in arg for lines of interest
1736 * (use |'ed TIOCM_RNG/DSR/CD/CTS for masking)
1737 * Caller should use TIOCGICOUNT to see which one it was
1740 spin_lock_irqsave(&info->slock, flags);
1741 cnow = info->icount; /* note the counters on entry */
1742 spin_unlock_irqrestore(&info->slock, flags);
1744 return wait_event_interruptible(info->port.delta_msr_wait,
1745 mxser_cflags_changed(info, arg, &cnow));
1746 case MOXA_HighSpeedOn:
1747 return put_user(info->baud_base != 115200 ? 1 : 0, (int __user *)argp);
1748 case MOXA_SDS_RSTICOUNTER:
1749 spin_lock_irq(&info->slock);
1750 info->mon_data.rxcnt = 0;
1751 info->mon_data.txcnt = 0;
1752 spin_unlock_irq(&info->slock);
1755 case MOXA_ASPP_OQUEUE:{
1758 len = mxser_chars_in_buffer(tty);
1759 spin_lock_irq(&info->slock);
1760 lsr = inb(info->ioaddr + UART_LSR) & UART_LSR_THRE;
1761 spin_unlock_irq(&info->slock);
1762 len += (lsr ? 0 : 1);
1764 return put_user(len, (int __user *)argp);
1766 case MOXA_ASPP_MON: {
1769 spin_lock_irq(&info->slock);
1770 status = mxser_get_msr(info->ioaddr, 1, tty->index);
1771 mxser_check_modem_status(tty, info, status);
1773 mcr = inb(info->ioaddr + UART_MCR);
1774 spin_unlock_irq(&info->slock);
1776 if (mcr & MOXA_MUST_MCR_XON_FLAG)
1777 info->mon_data.hold_reason &= ~NPPI_NOTIFY_XOFFHOLD;
1779 info->mon_data.hold_reason |= NPPI_NOTIFY_XOFFHOLD;
1781 if (mcr & MOXA_MUST_MCR_TX_XON)
1782 info->mon_data.hold_reason &= ~NPPI_NOTIFY_XOFFXENT;
1784 info->mon_data.hold_reason |= NPPI_NOTIFY_XOFFXENT;
1786 if (tty->hw_stopped)
1787 info->mon_data.hold_reason |= NPPI_NOTIFY_CTSHOLD;
1789 info->mon_data.hold_reason &= ~NPPI_NOTIFY_CTSHOLD;
1791 if (copy_to_user(argp, &info->mon_data,
1792 sizeof(struct mxser_mon)))
1797 case MOXA_ASPP_LSTATUS: {
1798 if (put_user(info->err_shadow, (unsigned char __user *)argp))
1801 info->err_shadow = 0;
1804 case MOXA_SET_BAUD_METHOD: {
1807 if (get_user(method, (int __user *)argp))
1809 mxser_set_baud_method[tty->index] = method;
1810 return put_user(method, (int __user *)argp);
1813 return -ENOIOCTLCMD;
1819 * Get counter of input serial line interrupts (DCD,RI,DSR,CTS)
1820 * Return: write counters to the user passed counter struct
1821 * NB: both 1->0 and 0->1 transitions are counted except for
1822 * RI where only 0->1 is counted.
1825 static int mxser_get_icount(struct tty_struct *tty,
1826 struct serial_icounter_struct *icount)
1829 struct mxser_port *info = tty->driver_data;
1830 struct async_icount cnow;
1831 unsigned long flags;
1833 spin_lock_irqsave(&info->slock, flags);
1834 cnow = info->icount;
1835 spin_unlock_irqrestore(&info->slock, flags);
1837 icount->frame = cnow.frame;
1838 icount->brk = cnow.brk;
1839 icount->overrun = cnow.overrun;
1840 icount->buf_overrun = cnow.buf_overrun;
1841 icount->parity = cnow.parity;
1842 icount->rx = cnow.rx;
1843 icount->tx = cnow.tx;
1844 icount->cts = cnow.cts;
1845 icount->dsr = cnow.dsr;
1846 icount->rng = cnow.rng;
1847 icount->dcd = cnow.dcd;
1851 static void mxser_stoprx(struct tty_struct *tty)
1853 struct mxser_port *info = tty->driver_data;
1855 info->ldisc_stop_rx = 1;
1857 if (info->board->chip_flag) {
1858 info->IER &= ~MOXA_MUST_RECV_ISR;
1859 outb(info->IER, info->ioaddr + UART_IER);
1861 info->x_char = STOP_CHAR(tty);
1862 outb(0, info->ioaddr + UART_IER);
1863 info->IER |= UART_IER_THRI;
1864 outb(info->IER, info->ioaddr + UART_IER);
1868 if (C_CRTSCTS(tty)) {
1869 info->MCR &= ~UART_MCR_RTS;
1870 outb(info->MCR, info->ioaddr + UART_MCR);
1875 * This routine is called by the upper-layer tty layer to signal that
1876 * incoming characters should be throttled.
1878 static void mxser_throttle(struct tty_struct *tty)
1883 static void mxser_unthrottle(struct tty_struct *tty)
1885 struct mxser_port *info = tty->driver_data;
1888 info->ldisc_stop_rx = 0;
1893 if (info->board->chip_flag) {
1894 info->IER |= MOXA_MUST_RECV_ISR;
1895 outb(info->IER, info->ioaddr + UART_IER);
1897 info->x_char = START_CHAR(tty);
1898 outb(0, info->ioaddr + UART_IER);
1899 info->IER |= UART_IER_THRI;
1900 outb(info->IER, info->ioaddr + UART_IER);
1905 if (C_CRTSCTS(tty)) {
1906 info->MCR |= UART_MCR_RTS;
1907 outb(info->MCR, info->ioaddr + UART_MCR);
1912 * mxser_stop() and mxser_start()
1914 * This routines are called before setting or resetting tty->stopped.
1915 * They enable or disable transmitter interrupts, as necessary.
1917 static void mxser_stop(struct tty_struct *tty)
1919 struct mxser_port *info = tty->driver_data;
1920 unsigned long flags;
1922 spin_lock_irqsave(&info->slock, flags);
1923 if (info->IER & UART_IER_THRI) {
1924 info->IER &= ~UART_IER_THRI;
1925 outb(info->IER, info->ioaddr + UART_IER);
1927 spin_unlock_irqrestore(&info->slock, flags);
1930 static void mxser_start(struct tty_struct *tty)
1932 struct mxser_port *info = tty->driver_data;
1933 unsigned long flags;
1935 spin_lock_irqsave(&info->slock, flags);
1936 if (info->xmit_cnt && info->port.xmit_buf) {
1937 outb(info->IER & ~UART_IER_THRI, info->ioaddr + UART_IER);
1938 info->IER |= UART_IER_THRI;
1939 outb(info->IER, info->ioaddr + UART_IER);
1941 spin_unlock_irqrestore(&info->slock, flags);
1944 static void mxser_set_termios(struct tty_struct *tty, struct ktermios *old_termios)
1946 struct mxser_port *info = tty->driver_data;
1947 unsigned long flags;
1949 spin_lock_irqsave(&info->slock, flags);
1950 mxser_change_speed(tty, old_termios);
1951 spin_unlock_irqrestore(&info->slock, flags);
1953 if ((old_termios->c_cflag & CRTSCTS) && !C_CRTSCTS(tty)) {
1954 tty->hw_stopped = 0;
1958 /* Handle sw stopped */
1959 if ((old_termios->c_iflag & IXON) && !I_IXON(tty)) {
1962 if (info->board->chip_flag) {
1963 spin_lock_irqsave(&info->slock, flags);
1964 mxser_disable_must_rx_software_flow_control(
1966 spin_unlock_irqrestore(&info->slock, flags);
1974 * mxser_wait_until_sent() --- wait until the transmitter is empty
1976 static void mxser_wait_until_sent(struct tty_struct *tty, int timeout)
1978 struct mxser_port *info = tty->driver_data;
1979 unsigned long orig_jiffies, char_time;
1980 unsigned long flags;
1983 if (info->type == PORT_UNKNOWN)
1986 if (info->xmit_fifo_size == 0)
1987 return; /* Just in case.... */
1989 orig_jiffies = jiffies;
1991 * Set the check interval to be 1/5 of the estimated time to
1992 * send a single character, and make it at least 1. The check
1993 * interval should also be less than the timeout.
1995 * Note: we have to use pretty tight timings here to satisfy
1998 char_time = (info->timeout - HZ / 50) / info->xmit_fifo_size;
1999 char_time = char_time / 5;
2002 if (timeout && timeout < char_time)
2003 char_time = timeout;
2005 * If the transmitter hasn't cleared in twice the approximate
2006 * amount of time to send the entire FIFO, it probably won't
2007 * ever clear. This assumes the UART isn't doing flow
2008 * control, which is currently the case. Hence, if it ever
2009 * takes longer than info->timeout, this is probably due to a
2010 * UART bug of some kind. So, we clamp the timeout parameter at
2013 if (!timeout || timeout > 2 * info->timeout)
2014 timeout = 2 * info->timeout;
2016 spin_lock_irqsave(&info->slock, flags);
2017 while (!((lsr = inb(info->ioaddr + UART_LSR)) & UART_LSR_TEMT)) {
2018 spin_unlock_irqrestore(&info->slock, flags);
2019 schedule_timeout_interruptible(char_time);
2020 spin_lock_irqsave(&info->slock, flags);
2021 if (signal_pending(current))
2023 if (timeout && time_after(jiffies, orig_jiffies + timeout))
2026 spin_unlock_irqrestore(&info->slock, flags);
2027 set_current_state(TASK_RUNNING);
2031 * This routine is called by tty_hangup() when a hangup is signaled.
2033 static void mxser_hangup(struct tty_struct *tty)
2035 struct mxser_port *info = tty->driver_data;
2037 mxser_flush_buffer(tty);
2038 tty_port_hangup(&info->port);
2042 * mxser_rs_break() --- routine which turns the break handling on or off
2044 static int mxser_rs_break(struct tty_struct *tty, int break_state)
2046 struct mxser_port *info = tty->driver_data;
2047 unsigned long flags;
2049 spin_lock_irqsave(&info->slock, flags);
2050 if (break_state == -1)
2051 outb(inb(info->ioaddr + UART_LCR) | UART_LCR_SBC,
2052 info->ioaddr + UART_LCR);
2054 outb(inb(info->ioaddr + UART_LCR) & ~UART_LCR_SBC,
2055 info->ioaddr + UART_LCR);
2056 spin_unlock_irqrestore(&info->slock, flags);
2060 static void mxser_receive_chars(struct tty_struct *tty,
2061 struct mxser_port *port, int *status)
2063 unsigned char ch, gdl;
2069 recv_room = tty->receive_room;
2070 if (recv_room == 0 && !port->ldisc_stop_rx)
2072 if (port->board->chip_flag != MOXA_OTHER_UART) {
2074 if (*status & UART_LSR_SPECIAL)
2076 if (port->board->chip_flag == MOXA_MUST_MU860_HWID &&
2077 (*status & MOXA_MUST_LSR_RERR))
2079 if (*status & MOXA_MUST_LSR_RERR)
2082 gdl = inb(port->ioaddr + MOXA_MUST_GDL_REGISTER);
2084 if (port->board->chip_flag == MOXA_MUST_MU150_HWID)
2085 gdl &= MOXA_MUST_GDL_MASK;
2086 if (gdl >= recv_room) {
2087 if (!port->ldisc_stop_rx)
2091 ch = inb(port->ioaddr + UART_RX);
2092 tty_insert_flip_char(&port->port, ch, 0);
2103 ch = inb(port->ioaddr + UART_RX);
2104 if (port->board->chip_flag && (*status & UART_LSR_OE))
2105 outb(0x23, port->ioaddr + UART_FCR);
2106 *status &= port->read_status_mask;
2107 if (*status & port->ignore_status_mask) {
2108 if (++ignored > 100)
2112 if (*status & UART_LSR_SPECIAL) {
2113 if (*status & UART_LSR_BI) {
2117 if (port->port.flags & ASYNC_SAK)
2119 } else if (*status & UART_LSR_PE) {
2121 port->icount.parity++;
2122 } else if (*status & UART_LSR_FE) {
2124 port->icount.frame++;
2125 } else if (*status & UART_LSR_OE) {
2127 port->icount.overrun++;
2131 tty_insert_flip_char(&port->port, ch, flag);
2133 if (cnt >= recv_room) {
2134 if (!port->ldisc_stop_rx)
2141 if (port->board->chip_flag)
2144 *status = inb(port->ioaddr + UART_LSR);
2145 } while (*status & UART_LSR_DR);
2148 mxvar_log.rxcnt[tty->index] += cnt;
2149 port->mon_data.rxcnt += cnt;
2150 port->mon_data.up_rxcnt += cnt;
2153 * We are called from an interrupt context with &port->slock
2154 * being held. Drop it temporarily in order to prevent
2155 * recursive locking.
2157 spin_unlock(&port->slock);
2158 tty_flip_buffer_push(&port->port);
2159 spin_lock(&port->slock);
2162 static void mxser_transmit_chars(struct tty_struct *tty, struct mxser_port *port)
2167 outb(port->x_char, port->ioaddr + UART_TX);
2169 mxvar_log.txcnt[tty->index]++;
2170 port->mon_data.txcnt++;
2171 port->mon_data.up_txcnt++;
2176 if (port->port.xmit_buf == NULL)
2179 if (port->xmit_cnt <= 0 || tty->stopped ||
2181 (port->type != PORT_16550A) &&
2182 (!port->board->chip_flag))) {
2183 port->IER &= ~UART_IER_THRI;
2184 outb(port->IER, port->ioaddr + UART_IER);
2188 cnt = port->xmit_cnt;
2189 count = port->xmit_fifo_size;
2191 outb(port->port.xmit_buf[port->xmit_tail++],
2192 port->ioaddr + UART_TX);
2193 port->xmit_tail = port->xmit_tail & (SERIAL_XMIT_SIZE - 1);
2194 if (--port->xmit_cnt <= 0)
2196 } while (--count > 0);
2197 mxvar_log.txcnt[tty->index] += (cnt - port->xmit_cnt);
2199 port->mon_data.txcnt += (cnt - port->xmit_cnt);
2200 port->mon_data.up_txcnt += (cnt - port->xmit_cnt);
2201 port->icount.tx += (cnt - port->xmit_cnt);
2203 if (port->xmit_cnt < WAKEUP_CHARS)
2206 if (port->xmit_cnt <= 0) {
2207 port->IER &= ~UART_IER_THRI;
2208 outb(port->IER, port->ioaddr + UART_IER);
2213 * This is the serial driver's generic interrupt routine
2215 static irqreturn_t mxser_interrupt(int irq, void *dev_id)
2218 struct mxser_board *brd = NULL;
2219 struct mxser_port *port;
2220 int max, irqbits, bits, msr;
2221 unsigned int int_cnt, pass_counter = 0;
2222 int handled = IRQ_NONE;
2223 struct tty_struct *tty;
2225 for (i = 0; i < MXSER_BOARDS; i++)
2226 if (dev_id == &mxser_boards[i]) {
2231 if (i == MXSER_BOARDS)
2235 max = brd->info->nports;
2236 while (pass_counter++ < MXSER_ISR_PASS_LIMIT) {
2237 irqbits = inb(brd->vector) & brd->vector_mask;
2238 if (irqbits == brd->vector_mask)
2241 handled = IRQ_HANDLED;
2242 for (i = 0, bits = 1; i < max; i++, irqbits |= bits, bits <<= 1) {
2243 if (irqbits == brd->vector_mask)
2247 port = &brd->ports[i];
2250 spin_lock(&port->slock);
2252 iir = inb(port->ioaddr + UART_IIR);
2253 if (iir & UART_IIR_NO_INT)
2255 iir &= MOXA_MUST_IIR_MASK;
2256 tty = tty_port_tty_get(&port->port);
2257 if (!tty || port->closing ||
2258 !tty_port_initialized(&port->port)) {
2259 status = inb(port->ioaddr + UART_LSR);
2260 outb(0x27, port->ioaddr + UART_FCR);
2261 inb(port->ioaddr + UART_MSR);
2266 status = inb(port->ioaddr + UART_LSR);
2268 if (status & UART_LSR_PE)
2269 port->err_shadow |= NPPI_NOTIFY_PARITY;
2270 if (status & UART_LSR_FE)
2271 port->err_shadow |= NPPI_NOTIFY_FRAMING;
2272 if (status & UART_LSR_OE)
2274 NPPI_NOTIFY_HW_OVERRUN;
2275 if (status & UART_LSR_BI)
2276 port->err_shadow |= NPPI_NOTIFY_BREAK;
2278 if (port->board->chip_flag) {
2279 if (iir == MOXA_MUST_IIR_GDA ||
2280 iir == MOXA_MUST_IIR_RDA ||
2281 iir == MOXA_MUST_IIR_RTO ||
2282 iir == MOXA_MUST_IIR_LSR)
2283 mxser_receive_chars(tty, port,
2287 status &= port->read_status_mask;
2288 if (status & UART_LSR_DR)
2289 mxser_receive_chars(tty, port,
2292 msr = inb(port->ioaddr + UART_MSR);
2293 if (msr & UART_MSR_ANY_DELTA)
2294 mxser_check_modem_status(tty, port, msr);
2296 if (port->board->chip_flag) {
2297 if (iir == 0x02 && (status &
2299 mxser_transmit_chars(tty, port);
2301 if (status & UART_LSR_THRE)
2302 mxser_transmit_chars(tty, port);
2305 } while (int_cnt++ < MXSER_ISR_PASS_LIMIT);
2306 spin_unlock(&port->slock);
2314 static const struct tty_operations mxser_ops = {
2316 .close = mxser_close,
2317 .write = mxser_write,
2318 .put_char = mxser_put_char,
2319 .flush_chars = mxser_flush_chars,
2320 .write_room = mxser_write_room,
2321 .chars_in_buffer = mxser_chars_in_buffer,
2322 .flush_buffer = mxser_flush_buffer,
2323 .ioctl = mxser_ioctl,
2324 .throttle = mxser_throttle,
2325 .unthrottle = mxser_unthrottle,
2326 .set_termios = mxser_set_termios,
2328 .start = mxser_start,
2329 .hangup = mxser_hangup,
2330 .break_ctl = mxser_rs_break,
2331 .wait_until_sent = mxser_wait_until_sent,
2332 .tiocmget = mxser_tiocmget,
2333 .tiocmset = mxser_tiocmset,
2334 .get_icount = mxser_get_icount,
2337 static const struct tty_port_operations mxser_port_ops = {
2338 .carrier_raised = mxser_carrier_raised,
2339 .dtr_rts = mxser_dtr_rts,
2340 .activate = mxser_activate,
2341 .shutdown = mxser_shutdown_port,
2345 * The MOXA Smartio/Industio serial driver boot-time initialization code!
2348 static bool allow_overlapping_vector;
2349 module_param(allow_overlapping_vector, bool, S_IRUGO);
2350 MODULE_PARM_DESC(allow_overlapping_vector, "whether we allow ISA cards to be configured such that vector overlabs IO ports (default=no)");
2352 static bool mxser_overlapping_vector(struct mxser_board *brd)
2354 return allow_overlapping_vector &&
2355 brd->vector >= brd->ports[0].ioaddr &&
2356 brd->vector < brd->ports[0].ioaddr + 8 * brd->info->nports;
2359 static int mxser_request_vector(struct mxser_board *brd)
2361 if (mxser_overlapping_vector(brd))
2363 return request_region(brd->vector, 1, "mxser(vector)") ? 0 : -EIO;
2366 static void mxser_release_vector(struct mxser_board *brd)
2368 if (mxser_overlapping_vector(brd))
2370 release_region(brd->vector, 1);
2373 static void mxser_release_ISA_res(struct mxser_board *brd)
2375 release_region(brd->ports[0].ioaddr, 8 * brd->info->nports);
2376 mxser_release_vector(brd);
2379 static int mxser_initbrd(struct mxser_board *brd,
2380 struct pci_dev *pdev)
2382 struct mxser_port *info;
2386 printk(KERN_INFO "mxser: max. baud rate = %d bps\n",
2387 brd->ports[0].max_baud);
2389 for (i = 0; i < brd->info->nports; i++) {
2390 info = &brd->ports[i];
2391 tty_port_init(&info->port);
2392 info->port.ops = &mxser_port_ops;
2395 info->ldisc_stop_rx = 0;
2397 /* Enhance mode enabled here */
2398 if (brd->chip_flag != MOXA_OTHER_UART)
2399 mxser_enable_must_enchance_mode(info->ioaddr);
2401 info->type = brd->uart_type;
2403 process_txrx_fifo(info);
2405 info->custom_divisor = info->baud_base * 16;
2406 info->port.close_delay = 5 * HZ / 10;
2407 info->port.closing_wait = 30 * HZ;
2408 info->normal_termios = mxvar_sdriver->init_termios;
2409 memset(&info->mon_data, 0, sizeof(struct mxser_mon));
2410 info->err_shadow = 0;
2411 spin_lock_init(&info->slock);
2413 /* before set INT ISR, disable all int */
2414 outb(inb(info->ioaddr + UART_IER) & 0xf0,
2415 info->ioaddr + UART_IER);
2418 retval = request_irq(brd->irq, mxser_interrupt, IRQF_SHARED, "mxser",
2421 for (i = 0; i < brd->info->nports; i++)
2422 tty_port_destroy(&brd->ports[i].port);
2423 printk(KERN_ERR "Board %s: Request irq failed, IRQ (%d) may "
2424 "conflict with another device.\n",
2425 brd->info->name, brd->irq);
2431 static void mxser_board_remove(struct mxser_board *brd)
2435 for (i = 0; i < brd->info->nports; i++) {
2436 tty_unregister_device(mxvar_sdriver, brd->idx + i);
2437 tty_port_destroy(&brd->ports[i].port);
2439 free_irq(brd->irq, brd);
2442 static int __init mxser_get_ISA_conf(int cap, struct mxser_board *brd)
2444 int id, i, bits, ret;
2445 unsigned short regs[16], irq;
2446 unsigned char scratch, scratch2;
2448 brd->chip_flag = MOXA_OTHER_UART;
2450 id = mxser_read_register(cap, regs);
2453 brd->info = &mxser_cards[0];
2456 brd->info = &mxser_cards[1];
2458 case CI104J_ASIC_ID:
2459 brd->info = &mxser_cards[2];
2462 brd->info = &mxser_cards[5];
2465 brd->info = &mxser_cards[6];
2468 brd->info = &mxser_cards[7];
2475 /* some ISA cards have 2 ports, but we want to see them as 4-port (why?)
2476 Flag-hack checks if configuration should be read as 2-port here. */
2477 if (brd->info->nports == 2 || (brd->info->flags & MXSER_HAS2)) {
2478 irq = regs[9] & 0xF000;
2479 irq = irq | (irq >> 4);
2480 if (irq != (regs[9] & 0xFF00))
2481 goto err_irqconflict;
2482 } else if (brd->info->nports == 4) {
2483 irq = regs[9] & 0xF000;
2484 irq = irq | (irq >> 4);
2485 irq = irq | (irq >> 8);
2487 goto err_irqconflict;
2488 } else if (brd->info->nports == 8) {
2489 irq = regs[9] & 0xF000;
2490 irq = irq | (irq >> 4);
2491 irq = irq | (irq >> 8);
2492 if ((irq != regs[9]) || (irq != regs[10]))
2493 goto err_irqconflict;
2497 printk(KERN_ERR "mxser: interrupt number unset\n");
2500 brd->irq = ((int)(irq & 0xF000) >> 12);
2501 for (i = 0; i < 8; i++)
2502 brd->ports[i].ioaddr = (int) regs[i + 1] & 0xFFF8;
2503 if ((regs[12] & 0x80) == 0) {
2504 printk(KERN_ERR "mxser: invalid interrupt vector\n");
2507 brd->vector = (int)regs[11]; /* interrupt vector */
2509 brd->vector_mask = 0x00FF;
2511 brd->vector_mask = 0x000F;
2512 for (i = 7, bits = 0x0100; i >= 0; i--, bits <<= 1) {
2513 if (regs[12] & bits) {
2514 brd->ports[i].baud_base = 921600;
2515 brd->ports[i].max_baud = 921600;
2517 brd->ports[i].baud_base = 115200;
2518 brd->ports[i].max_baud = 115200;
2521 scratch2 = inb(cap + UART_LCR) & (~UART_LCR_DLAB);
2522 outb(scratch2 | UART_LCR_DLAB, cap + UART_LCR);
2523 outb(0, cap + UART_EFR); /* EFR is the same as FCR */
2524 outb(scratch2, cap + UART_LCR);
2525 outb(UART_FCR_ENABLE_FIFO, cap + UART_FCR);
2526 scratch = inb(cap + UART_IIR);
2529 brd->uart_type = PORT_16550A;
2531 brd->uart_type = PORT_16450;
2532 if (!request_region(brd->ports[0].ioaddr, 8 * brd->info->nports,
2534 printk(KERN_ERR "mxser: can't request ports I/O region: "
2535 "0x%.8lx-0x%.8lx\n",
2536 brd->ports[0].ioaddr, brd->ports[0].ioaddr +
2537 8 * brd->info->nports - 1);
2541 ret = mxser_request_vector(brd);
2543 release_region(brd->ports[0].ioaddr, 8 * brd->info->nports);
2544 printk(KERN_ERR "mxser: can't request interrupt vector region: "
2545 "0x%.8lx-0x%.8lx\n",
2546 brd->ports[0].ioaddr, brd->ports[0].ioaddr +
2547 8 * brd->info->nports - 1);
2550 return brd->info->nports;
2553 printk(KERN_ERR "mxser: invalid interrupt number\n");
2557 static int mxser_probe(struct pci_dev *pdev,
2558 const struct pci_device_id *ent)
2561 struct mxser_board *brd;
2563 unsigned long ioaddress;
2564 struct device *tty_dev;
2565 int retval = -EINVAL;
2567 for (i = 0; i < MXSER_BOARDS; i++)
2568 if (mxser_boards[i].info == NULL)
2571 if (i >= MXSER_BOARDS) {
2572 dev_err(&pdev->dev, "too many boards found (maximum %d), board "
2573 "not configured\n", MXSER_BOARDS);
2577 brd = &mxser_boards[i];
2578 brd->idx = i * MXSER_PORTS_PER_BOARD;
2579 dev_info(&pdev->dev, "found MOXA %s board (BusNo=%d, DevNo=%d)\n",
2580 mxser_cards[ent->driver_data].name,
2581 pdev->bus->number, PCI_SLOT(pdev->devfn));
2583 retval = pci_enable_device(pdev);
2585 dev_err(&pdev->dev, "PCI enable failed\n");
2590 ioaddress = pci_resource_start(pdev, 2);
2591 retval = pci_request_region(pdev, 2, "mxser(IO)");
2595 brd->info = &mxser_cards[ent->driver_data];
2596 for (i = 0; i < brd->info->nports; i++)
2597 brd->ports[i].ioaddr = ioaddress + 8 * i;
2600 ioaddress = pci_resource_start(pdev, 3);
2601 retval = pci_request_region(pdev, 3, "mxser(vector)");
2604 brd->vector = ioaddress;
2607 brd->irq = pdev->irq;
2609 brd->chip_flag = CheckIsMoxaMust(brd->ports[0].ioaddr);
2610 brd->uart_type = PORT_16550A;
2611 brd->vector_mask = 0;
2613 for (i = 0; i < brd->info->nports; i++) {
2614 for (j = 0; j < UART_INFO_NUM; j++) {
2615 if (Gpci_uart_info[j].type == brd->chip_flag) {
2616 brd->ports[i].max_baud =
2617 Gpci_uart_info[j].max_baud;
2619 /* exception....CP-102 */
2620 if (brd->info->flags & MXSER_HIGHBAUD)
2621 brd->ports[i].max_baud = 921600;
2627 if (brd->chip_flag == MOXA_MUST_MU860_HWID) {
2628 for (i = 0; i < brd->info->nports; i++) {
2630 brd->ports[i].opmode_ioaddr = ioaddress + 4;
2632 brd->ports[i].opmode_ioaddr = ioaddress + 0x0c;
2634 outb(0, ioaddress + 4); /* default set to RS232 mode */
2635 outb(0, ioaddress + 0x0c); /* default set to RS232 mode */
2638 for (i = 0; i < brd->info->nports; i++) {
2639 brd->vector_mask |= (1 << i);
2640 brd->ports[i].baud_base = 921600;
2643 /* mxser_initbrd will hook ISR. */
2644 retval = mxser_initbrd(brd, pdev);
2648 for (i = 0; i < brd->info->nports; i++) {
2649 tty_dev = tty_port_register_device(&brd->ports[i].port,
2650 mxvar_sdriver, brd->idx + i, &pdev->dev);
2651 if (IS_ERR(tty_dev)) {
2652 retval = PTR_ERR(tty_dev);
2654 tty_unregister_device(mxvar_sdriver,
2660 pci_set_drvdata(pdev, brd);
2664 for (i = 0; i < brd->info->nports; i++)
2665 tty_port_destroy(&brd->ports[i].port);
2666 free_irq(brd->irq, brd);
2668 pci_release_region(pdev, 3);
2671 pci_release_region(pdev, 2);
2673 pci_disable_device(pdev);
2681 static void mxser_remove(struct pci_dev *pdev)
2684 struct mxser_board *brd = pci_get_drvdata(pdev);
2686 mxser_board_remove(brd);
2688 pci_release_region(pdev, 2);
2689 pci_release_region(pdev, 3);
2690 pci_disable_device(pdev);
2695 static struct pci_driver mxser_driver = {
2697 .id_table = mxser_pcibrds,
2698 .probe = mxser_probe,
2699 .remove = mxser_remove
2702 static int __init mxser_module_init(void)
2704 struct mxser_board *brd;
2705 struct device *tty_dev;
2706 unsigned int b, i, m;
2709 mxvar_sdriver = alloc_tty_driver(MXSER_PORTS + 1);
2713 printk(KERN_INFO "MOXA Smartio/Industio family driver version %s\n",
2716 /* Initialize the tty_driver structure */
2717 mxvar_sdriver->name = "ttyMI";
2718 mxvar_sdriver->major = ttymajor;
2719 mxvar_sdriver->minor_start = 0;
2720 mxvar_sdriver->type = TTY_DRIVER_TYPE_SERIAL;
2721 mxvar_sdriver->subtype = SERIAL_TYPE_NORMAL;
2722 mxvar_sdriver->init_termios = tty_std_termios;
2723 mxvar_sdriver->init_termios.c_cflag = B9600|CS8|CREAD|HUPCL|CLOCAL;
2724 mxvar_sdriver->flags = TTY_DRIVER_REAL_RAW|TTY_DRIVER_DYNAMIC_DEV;
2725 tty_set_operations(mxvar_sdriver, &mxser_ops);
2727 retval = tty_register_driver(mxvar_sdriver);
2729 printk(KERN_ERR "Couldn't install MOXA Smartio/Industio family "
2734 /* Start finding ISA boards here */
2735 for (m = 0, b = 0; b < MXSER_BOARDS; b++) {
2739 brd = &mxser_boards[m];
2740 retval = mxser_get_ISA_conf(ioaddr[b], brd);
2746 printk(KERN_INFO "mxser: found MOXA %s board (CAP=0x%lx)\n",
2747 brd->info->name, ioaddr[b]);
2749 /* mxser_initbrd will hook ISR. */
2750 if (mxser_initbrd(brd, NULL) < 0) {
2751 mxser_release_ISA_res(brd);
2756 brd->idx = m * MXSER_PORTS_PER_BOARD;
2757 for (i = 0; i < brd->info->nports; i++) {
2758 tty_dev = tty_port_register_device(&brd->ports[i].port,
2759 mxvar_sdriver, brd->idx + i, NULL);
2760 if (IS_ERR(tty_dev)) {
2762 tty_unregister_device(mxvar_sdriver,
2764 for (i = 0; i < brd->info->nports; i++)
2765 tty_port_destroy(&brd->ports[i].port);
2766 free_irq(brd->irq, brd);
2767 mxser_release_ISA_res(brd);
2772 if (brd->info == NULL)
2778 retval = pci_register_driver(&mxser_driver);
2780 printk(KERN_ERR "mxser: can't register pci driver\n");
2784 } /* else: we have some ISA cards under control */
2789 tty_unregister_driver(mxvar_sdriver);
2791 put_tty_driver(mxvar_sdriver);
2795 static void __exit mxser_module_exit(void)
2799 pci_unregister_driver(&mxser_driver);
2801 for (i = 0; i < MXSER_BOARDS; i++) /* ISA remains */
2802 if (mxser_boards[i].info != NULL)
2803 mxser_board_remove(&mxser_boards[i]);
2804 tty_unregister_driver(mxvar_sdriver);
2805 put_tty_driver(mxvar_sdriver);
2807 for (i = 0; i < MXSER_BOARDS; i++)
2808 if (mxser_boards[i].info != NULL)
2809 mxser_release_ISA_res(&mxser_boards[i]);
2812 module_init(mxser_module_init);
2813 module_exit(mxser_module_exit);