1 #ifndef __LINUX_NL80211_H
2 #define __LINUX_NL80211_H
4 * 802.11 netlink interface public header
6 * Copyright 2006-2010 Johannes Berg <johannes@sipsolutions.net>
7 * Copyright 2008 Michael Wu <flamingice@sourmilk.net>
8 * Copyright 2008 Luis Carlos Cobo <luisca@cozybit.com>
9 * Copyright 2008 Michael Buesch <m@bues.ch>
10 * Copyright 2008, 2009 Luis R. Rodriguez <lrodriguez@atheros.com>
11 * Copyright 2008 Jouni Malinen <jouni.malinen@atheros.com>
12 * Copyright 2008 Colin McCabe <colin@cozybit.com>
13 * Copyright 2015 Intel Deutschland GmbH
15 * Permission to use, copy, modify, and/or distribute this software for any
16 * purpose with or without fee is hereby granted, provided that the above
17 * copyright notice and this permission notice appear in all copies.
19 * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
20 * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
21 * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
22 * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
23 * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
24 * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
25 * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
30 * This header file defines the userspace API to the wireless stack. Please
31 * be careful not to break things - i.e. don't move anything around or so
32 * unless you can demonstrate that it breaks neither API nor ABI.
34 * Additions to the API should be accompanied by actual implementations in
35 * an upstream driver, so that example implementations exist in case there
36 * are ever concerns about the precise semantics of the API or changes are
37 * needed, and to ensure that code for dead (no longer implemented) API
38 * can actually be identified and removed.
39 * Nonetheless, semantics should also be documented carefully in this file.
42 #include <linux/types.h>
44 #define NL80211_GENL_NAME "nl80211"
46 #define NL80211_MULTICAST_GROUP_CONFIG "config"
47 #define NL80211_MULTICAST_GROUP_SCAN "scan"
48 #define NL80211_MULTICAST_GROUP_REG "regulatory"
49 #define NL80211_MULTICAST_GROUP_MLME "mlme"
50 #define NL80211_MULTICAST_GROUP_VENDOR "vendor"
51 #define NL80211_MULTICAST_GROUP_TESTMODE "testmode"
54 * DOC: Station handling
56 * Stations are added per interface, but a special case exists with VLAN
57 * interfaces. When a station is bound to an AP interface, it may be moved
58 * into a VLAN identified by a VLAN interface index (%NL80211_ATTR_STA_VLAN).
59 * The station is still assumed to belong to the AP interface it was added
62 * Station handling varies per interface type and depending on the driver's
65 * For drivers supporting TDLS with external setup (WIPHY_FLAG_SUPPORTS_TDLS
66 * and WIPHY_FLAG_TDLS_EXTERNAL_SETUP), the station lifetime is as follows:
67 * - a setup station entry is added, not yet authorized, without any rate
68 * or capability information, this just exists to avoid race conditions
69 * - when the TDLS setup is done, a single NL80211_CMD_SET_STATION is valid
70 * to add rate and capability information to the station and at the same
71 * time mark it authorized.
72 * - %NL80211_TDLS_ENABLE_LINK is then used
73 * - after this, the only valid operation is to remove it by tearing down
74 * the TDLS link (%NL80211_TDLS_DISABLE_LINK)
76 * TODO: need more info for other interface types
80 * DOC: Frame transmission/registration support
82 * Frame transmission and registration support exists to allow userspace
83 * management entities such as wpa_supplicant react to management frames
84 * that are not being handled by the kernel. This includes, for example,
85 * certain classes of action frames that cannot be handled in the kernel
86 * for various reasons.
88 * Frame registration is done on a per-interface basis and registrations
89 * cannot be removed other than by closing the socket. It is possible to
90 * specify a registration filter to register, for example, only for a
91 * certain type of action frame. In particular with action frames, those
92 * that userspace registers for will not be returned as unhandled by the
93 * driver, so that the registered application has to take responsibility
96 * The type of frame that can be registered for is also dependent on the
97 * driver and interface type. The frame types are advertised in wiphy
98 * attributes so applications know what to expect.
100 * NOTE: When an interface changes type while registrations are active,
101 * these registrations are ignored until the interface type is
102 * changed again. This means that changing the interface type can
103 * lead to a situation that couldn't otherwise be produced, but
104 * any such registrations will be dormant in the sense that they
105 * will not be serviced, i.e. they will not receive any frames.
107 * Frame transmission allows userspace to send for example the required
108 * responses to action frames. It is subject to some sanity checking,
109 * but many frames can be transmitted. When a frame was transmitted, its
110 * status is indicated to the sending socket.
112 * For more technical details, see the corresponding command descriptions
117 * DOC: Virtual interface / concurrency capabilities
119 * Some devices are able to operate with virtual MACs, they can have
120 * more than one virtual interface. The capability handling for this
121 * is a bit complex though, as there may be a number of restrictions
122 * on the types of concurrency that are supported.
124 * To start with, each device supports the interface types listed in
125 * the %NL80211_ATTR_SUPPORTED_IFTYPES attribute, but by listing the
126 * types there no concurrency is implied.
128 * Once concurrency is desired, more attributes must be observed:
129 * To start with, since some interface types are purely managed in
130 * software, like the AP-VLAN type in mac80211 for example, there's
131 * an additional list of these, they can be added at any time and
132 * are only restricted by some semantic restrictions (e.g. AP-VLAN
133 * cannot be added without a corresponding AP interface). This list
134 * is exported in the %NL80211_ATTR_SOFTWARE_IFTYPES attribute.
136 * Further, the list of supported combinations is exported. This is
137 * in the %NL80211_ATTR_INTERFACE_COMBINATIONS attribute. Basically,
138 * it exports a list of "groups", and at any point in time the
139 * interfaces that are currently active must fall into any one of
140 * the advertised groups. Within each group, there are restrictions
141 * on the number of interfaces of different types that are supported
142 * and also the number of different channels, along with potentially
143 * some other restrictions. See &enum nl80211_if_combination_attrs.
145 * All together, these attributes define the concurrency of virtual
146 * interfaces that a given device supports.
150 * DOC: packet coalesce support
152 * In most cases, host that receives IPv4 and IPv6 multicast/broadcast
153 * packets does not do anything with these packets. Therefore the
154 * reception of these unwanted packets causes unnecessary processing
155 * and power consumption.
157 * Packet coalesce feature helps to reduce number of received interrupts
158 * to host by buffering these packets in firmware/hardware for some
159 * predefined time. Received interrupt will be generated when one of the
160 * following events occur.
161 * a) Expiration of hardware timer whose expiration time is set to maximum
162 * coalescing delay of matching coalesce rule.
163 * b) Coalescing buffer in hardware reaches it's limit.
164 * c) Packet doesn't match any of the configured coalesce rules.
166 * User needs to configure following parameters for creating a coalesce
168 * a) Maximum coalescing delay
169 * b) List of packet patterns which needs to be matched
170 * c) Condition for coalescence. pattern 'match' or 'no match'
171 * Multiple such rules can be created.
175 * enum nl80211_commands - supported nl80211 commands
177 * @NL80211_CMD_UNSPEC: unspecified command to catch errors
179 * @NL80211_CMD_GET_WIPHY: request information about a wiphy or dump request
180 * to get a list of all present wiphys.
181 * @NL80211_CMD_SET_WIPHY: set wiphy parameters, needs %NL80211_ATTR_WIPHY or
182 * %NL80211_ATTR_IFINDEX; can be used to set %NL80211_ATTR_WIPHY_NAME,
183 * %NL80211_ATTR_WIPHY_TXQ_PARAMS, %NL80211_ATTR_WIPHY_FREQ (and the
184 * attributes determining the channel width; this is used for setting
185 * monitor mode channel), %NL80211_ATTR_WIPHY_RETRY_SHORT,
186 * %NL80211_ATTR_WIPHY_RETRY_LONG, %NL80211_ATTR_WIPHY_FRAG_THRESHOLD,
187 * and/or %NL80211_ATTR_WIPHY_RTS_THRESHOLD.
188 * However, for setting the channel, see %NL80211_CMD_SET_CHANNEL
189 * instead, the support here is for backward compatibility only.
190 * @NL80211_CMD_NEW_WIPHY: Newly created wiphy, response to get request
191 * or rename notification. Has attributes %NL80211_ATTR_WIPHY and
192 * %NL80211_ATTR_WIPHY_NAME.
193 * @NL80211_CMD_DEL_WIPHY: Wiphy deleted. Has attributes
194 * %NL80211_ATTR_WIPHY and %NL80211_ATTR_WIPHY_NAME.
196 * @NL80211_CMD_GET_INTERFACE: Request an interface's configuration;
197 * either a dump request for all interfaces or a specific get with a
198 * single %NL80211_ATTR_IFINDEX is supported.
199 * @NL80211_CMD_SET_INTERFACE: Set type of a virtual interface, requires
200 * %NL80211_ATTR_IFINDEX and %NL80211_ATTR_IFTYPE.
201 * @NL80211_CMD_NEW_INTERFACE: Newly created virtual interface or response
202 * to %NL80211_CMD_GET_INTERFACE. Has %NL80211_ATTR_IFINDEX,
203 * %NL80211_ATTR_WIPHY and %NL80211_ATTR_IFTYPE attributes. Can also
204 * be sent from userspace to request creation of a new virtual interface,
205 * then requires attributes %NL80211_ATTR_WIPHY, %NL80211_ATTR_IFTYPE and
206 * %NL80211_ATTR_IFNAME.
207 * @NL80211_CMD_DEL_INTERFACE: Virtual interface was deleted, has attributes
208 * %NL80211_ATTR_IFINDEX and %NL80211_ATTR_WIPHY. Can also be sent from
209 * userspace to request deletion of a virtual interface, then requires
210 * attribute %NL80211_ATTR_IFINDEX.
212 * @NL80211_CMD_GET_KEY: Get sequence counter information for a key specified
213 * by %NL80211_ATTR_KEY_IDX and/or %NL80211_ATTR_MAC.
214 * @NL80211_CMD_SET_KEY: Set key attributes %NL80211_ATTR_KEY_DEFAULT,
215 * %NL80211_ATTR_KEY_DEFAULT_MGMT, or %NL80211_ATTR_KEY_THRESHOLD.
216 * @NL80211_CMD_NEW_KEY: add a key with given %NL80211_ATTR_KEY_DATA,
217 * %NL80211_ATTR_KEY_IDX, %NL80211_ATTR_MAC, %NL80211_ATTR_KEY_CIPHER,
218 * and %NL80211_ATTR_KEY_SEQ attributes.
219 * @NL80211_CMD_DEL_KEY: delete a key identified by %NL80211_ATTR_KEY_IDX
220 * or %NL80211_ATTR_MAC.
222 * @NL80211_CMD_GET_BEACON: (not used)
223 * @NL80211_CMD_SET_BEACON: change the beacon on an access point interface
224 * using the %NL80211_ATTR_BEACON_HEAD and %NL80211_ATTR_BEACON_TAIL
225 * attributes. For drivers that generate the beacon and probe responses
226 * internally, the following attributes must be provided: %NL80211_ATTR_IE,
227 * %NL80211_ATTR_IE_PROBE_RESP and %NL80211_ATTR_IE_ASSOC_RESP.
228 * @NL80211_CMD_START_AP: Start AP operation on an AP interface, parameters
229 * are like for %NL80211_CMD_SET_BEACON, and additionally parameters that
230 * do not change are used, these include %NL80211_ATTR_BEACON_INTERVAL,
231 * %NL80211_ATTR_DTIM_PERIOD, %NL80211_ATTR_SSID,
232 * %NL80211_ATTR_HIDDEN_SSID, %NL80211_ATTR_CIPHERS_PAIRWISE,
233 * %NL80211_ATTR_CIPHER_GROUP, %NL80211_ATTR_WPA_VERSIONS,
234 * %NL80211_ATTR_AKM_SUITES, %NL80211_ATTR_PRIVACY,
235 * %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_INACTIVITY_TIMEOUT,
236 * %NL80211_ATTR_ACL_POLICY and %NL80211_ATTR_MAC_ADDRS.
237 * The channel to use can be set on the interface or be given using the
238 * %NL80211_ATTR_WIPHY_FREQ and the attributes determining channel width.
239 * @NL80211_CMD_NEW_BEACON: old alias for %NL80211_CMD_START_AP
240 * @NL80211_CMD_STOP_AP: Stop AP operation on the given interface
241 * @NL80211_CMD_DEL_BEACON: old alias for %NL80211_CMD_STOP_AP
243 * @NL80211_CMD_GET_STATION: Get station attributes for station identified by
244 * %NL80211_ATTR_MAC on the interface identified by %NL80211_ATTR_IFINDEX.
245 * @NL80211_CMD_SET_STATION: Set station attributes for station identified by
246 * %NL80211_ATTR_MAC on the interface identified by %NL80211_ATTR_IFINDEX.
247 * @NL80211_CMD_NEW_STATION: Add a station with given attributes to the
248 * the interface identified by %NL80211_ATTR_IFINDEX.
249 * @NL80211_CMD_DEL_STATION: Remove a station identified by %NL80211_ATTR_MAC
250 * or, if no MAC address given, all stations, on the interface identified
251 * by %NL80211_ATTR_IFINDEX. %NL80211_ATTR_MGMT_SUBTYPE and
252 * %NL80211_ATTR_REASON_CODE can optionally be used to specify which type
253 * of disconnection indication should be sent to the station
254 * (Deauthentication or Disassociation frame and reason code for that
257 * @NL80211_CMD_GET_MPATH: Get mesh path attributes for mesh path to
258 * destination %NL80211_ATTR_MAC on the interface identified by
259 * %NL80211_ATTR_IFINDEX.
260 * @NL80211_CMD_SET_MPATH: Set mesh path attributes for mesh path to
261 * destination %NL80211_ATTR_MAC on the interface identified by
262 * %NL80211_ATTR_IFINDEX.
263 * @NL80211_CMD_NEW_MPATH: Create a new mesh path for the destination given by
264 * %NL80211_ATTR_MAC via %NL80211_ATTR_MPATH_NEXT_HOP.
265 * @NL80211_CMD_DEL_MPATH: Delete a mesh path to the destination given by
267 * @NL80211_CMD_NEW_PATH: Add a mesh path with given attributes to the
268 * the interface identified by %NL80211_ATTR_IFINDEX.
269 * @NL80211_CMD_DEL_PATH: Remove a mesh path identified by %NL80211_ATTR_MAC
270 * or, if no MAC address given, all mesh paths, on the interface identified
271 * by %NL80211_ATTR_IFINDEX.
272 * @NL80211_CMD_SET_BSS: Set BSS attributes for BSS identified by
273 * %NL80211_ATTR_IFINDEX.
275 * @NL80211_CMD_GET_REG: ask the wireless core to send us its currently set
276 * regulatory domain. If %NL80211_ATTR_WIPHY is specified and the device
277 * has a private regulatory domain, it will be returned. Otherwise, the
278 * global regdomain will be returned.
279 * A device will have a private regulatory domain if it uses the
280 * regulatory_hint() API. Even when a private regdomain is used the channel
281 * information will still be mended according to further hints from
282 * the regulatory core to help with compliance. A dump version of this API
283 * is now available which will returns the global regdomain as well as
284 * all private regdomains of present wiphys (for those that have it).
285 * If a wiphy is self-managed (%NL80211_ATTR_WIPHY_SELF_MANAGED_REG), then
286 * its private regdomain is the only valid one for it. The regulatory
287 * core is not used to help with compliance in this case.
288 * @NL80211_CMD_SET_REG: Set current regulatory domain. CRDA sends this command
289 * after being queried by the kernel. CRDA replies by sending a regulatory
290 * domain structure which consists of %NL80211_ATTR_REG_ALPHA set to our
291 * current alpha2 if it found a match. It also provides
292 * NL80211_ATTR_REG_RULE_FLAGS, and a set of regulatory rules. Each
293 * regulatory rule is a nested set of attributes given by
294 * %NL80211_ATTR_REG_RULE_FREQ_[START|END] and
295 * %NL80211_ATTR_FREQ_RANGE_MAX_BW with an attached power rule given by
296 * %NL80211_ATTR_REG_RULE_POWER_MAX_ANT_GAIN and
297 * %NL80211_ATTR_REG_RULE_POWER_MAX_EIRP.
298 * @NL80211_CMD_REQ_SET_REG: ask the wireless core to set the regulatory domain
299 * to the specified ISO/IEC 3166-1 alpha2 country code. The core will
300 * store this as a valid request and then query userspace for it.
302 * @NL80211_CMD_GET_MESH_CONFIG: Get mesh networking properties for the
303 * interface identified by %NL80211_ATTR_IFINDEX
305 * @NL80211_CMD_SET_MESH_CONFIG: Set mesh networking properties for the
306 * interface identified by %NL80211_ATTR_IFINDEX
308 * @NL80211_CMD_SET_MGMT_EXTRA_IE: Set extra IEs for management frames. The
309 * interface is identified with %NL80211_ATTR_IFINDEX and the management
310 * frame subtype with %NL80211_ATTR_MGMT_SUBTYPE. The extra IE data to be
311 * added to the end of the specified management frame is specified with
312 * %NL80211_ATTR_IE. If the command succeeds, the requested data will be
313 * added to all specified management frames generated by
314 * kernel/firmware/driver.
315 * Note: This command has been removed and it is only reserved at this
316 * point to avoid re-using existing command number. The functionality this
317 * command was planned for has been provided with cleaner design with the
318 * option to specify additional IEs in NL80211_CMD_TRIGGER_SCAN,
319 * NL80211_CMD_AUTHENTICATE, NL80211_CMD_ASSOCIATE,
320 * NL80211_CMD_DEAUTHENTICATE, and NL80211_CMD_DISASSOCIATE.
322 * @NL80211_CMD_GET_SCAN: get scan results
323 * @NL80211_CMD_TRIGGER_SCAN: trigger a new scan with the given parameters
324 * %NL80211_ATTR_TX_NO_CCK_RATE is used to decide whether to send the
325 * probe requests at CCK rate or not.
326 * @NL80211_CMD_NEW_SCAN_RESULTS: scan notification (as a reply to
327 * NL80211_CMD_GET_SCAN and on the "scan" multicast group)
328 * @NL80211_CMD_SCAN_ABORTED: scan was aborted, for unspecified reasons,
329 * partial scan results may be available
331 * @NL80211_CMD_START_SCHED_SCAN: start a scheduled scan at certain
332 * intervals and certain number of cycles, as specified by
333 * %NL80211_ATTR_SCHED_SCAN_PLANS. If %NL80211_ATTR_SCHED_SCAN_PLANS is
334 * not specified and only %NL80211_ATTR_SCHED_SCAN_INTERVAL is specified,
335 * scheduled scan will run in an infinite loop with the specified interval.
336 * These attributes are mutually exculsive,
337 * i.e. NL80211_ATTR_SCHED_SCAN_INTERVAL must not be passed if
338 * NL80211_ATTR_SCHED_SCAN_PLANS is defined.
339 * If for some reason scheduled scan is aborted by the driver, all scan
340 * plans are canceled (including scan plans that did not start yet).
341 * Like with normal scans, if SSIDs (%NL80211_ATTR_SCAN_SSIDS)
342 * are passed, they are used in the probe requests. For
343 * broadcast, a broadcast SSID must be passed (ie. an empty
344 * string). If no SSID is passed, no probe requests are sent and
345 * a passive scan is performed. %NL80211_ATTR_SCAN_FREQUENCIES,
346 * if passed, define which channels should be scanned; if not
347 * passed, all channels allowed for the current regulatory domain
348 * are used. Extra IEs can also be passed from the userspace by
349 * using the %NL80211_ATTR_IE attribute. The first cycle of the
350 * scheduled scan can be delayed by %NL80211_ATTR_SCHED_SCAN_DELAY
352 * @NL80211_CMD_STOP_SCHED_SCAN: stop a scheduled scan. Returns -ENOENT if
353 * scheduled scan is not running. The caller may assume that as soon
354 * as the call returns, it is safe to start a new scheduled scan again.
355 * @NL80211_CMD_SCHED_SCAN_RESULTS: indicates that there are scheduled scan
357 * @NL80211_CMD_SCHED_SCAN_STOPPED: indicates that the scheduled scan has
358 * stopped. The driver may issue this event at any time during a
359 * scheduled scan. One reason for stopping the scan is if the hardware
360 * does not support starting an association or a normal scan while running
361 * a scheduled scan. This event is also sent when the
362 * %NL80211_CMD_STOP_SCHED_SCAN command is received or when the interface
363 * is brought down while a scheduled scan was running.
365 * @NL80211_CMD_GET_SURVEY: get survey resuls, e.g. channel occupation
367 * @NL80211_CMD_NEW_SURVEY_RESULTS: survey data notification (as a reply to
368 * NL80211_CMD_GET_SURVEY and on the "scan" multicast group)
370 * @NL80211_CMD_SET_PMKSA: Add a PMKSA cache entry, using %NL80211_ATTR_MAC
371 * (for the BSSID) and %NL80211_ATTR_PMKID.
372 * @NL80211_CMD_DEL_PMKSA: Delete a PMKSA cache entry, using %NL80211_ATTR_MAC
373 * (for the BSSID) and %NL80211_ATTR_PMKID.
374 * @NL80211_CMD_FLUSH_PMKSA: Flush all PMKSA cache entries.
376 * @NL80211_CMD_REG_CHANGE: indicates to userspace the regulatory domain
377 * has been changed and provides details of the request information
378 * that caused the change such as who initiated the regulatory request
379 * (%NL80211_ATTR_REG_INITIATOR), the wiphy_idx
380 * (%NL80211_ATTR_REG_ALPHA2) on which the request was made from if
381 * the initiator was %NL80211_REGDOM_SET_BY_COUNTRY_IE or
382 * %NL80211_REGDOM_SET_BY_DRIVER, the type of regulatory domain
383 * set (%NL80211_ATTR_REG_TYPE), if the type of regulatory domain is
384 * %NL80211_REG_TYPE_COUNTRY the alpha2 to which we have moved on
385 * to (%NL80211_ATTR_REG_ALPHA2).
386 * @NL80211_CMD_REG_BEACON_HINT: indicates to userspace that an AP beacon
387 * has been found while world roaming thus enabling active scan or
388 * any mode of operation that initiates TX (beacons) on a channel
389 * where we would not have been able to do either before. As an example
390 * if you are world roaming (regulatory domain set to world or if your
391 * driver is using a custom world roaming regulatory domain) and while
392 * doing a passive scan on the 5 GHz band you find an AP there (if not
393 * on a DFS channel) you will now be able to actively scan for that AP
394 * or use AP mode on your card on that same channel. Note that this will
395 * never be used for channels 1-11 on the 2 GHz band as they are always
396 * enabled world wide. This beacon hint is only sent if your device had
397 * either disabled active scanning or beaconing on a channel. We send to
398 * userspace the wiphy on which we removed a restriction from
399 * (%NL80211_ATTR_WIPHY) and the channel on which this occurred
400 * before (%NL80211_ATTR_FREQ_BEFORE) and after (%NL80211_ATTR_FREQ_AFTER)
401 * the beacon hint was processed.
403 * @NL80211_CMD_AUTHENTICATE: authentication request and notification.
404 * This command is used both as a command (request to authenticate) and
405 * as an event on the "mlme" multicast group indicating completion of the
406 * authentication process.
407 * When used as a command, %NL80211_ATTR_IFINDEX is used to identify the
408 * interface. %NL80211_ATTR_MAC is used to specify PeerSTAAddress (and
409 * BSSID in case of station mode). %NL80211_ATTR_SSID is used to specify
410 * the SSID (mainly for association, but is included in authentication
411 * request, too, to help BSS selection. %NL80211_ATTR_WIPHY_FREQ is used
412 * to specify the frequence of the channel in MHz. %NL80211_ATTR_AUTH_TYPE
413 * is used to specify the authentication type. %NL80211_ATTR_IE is used to
414 * define IEs (VendorSpecificInfo, but also including RSN IE and FT IEs)
415 * to be added to the frame.
416 * When used as an event, this reports reception of an Authentication
417 * frame in station and IBSS modes when the local MLME processed the
418 * frame, i.e., it was for the local STA and was received in correct
419 * state. This is similar to MLME-AUTHENTICATE.confirm primitive in the
420 * MLME SAP interface (kernel providing MLME, userspace SME). The
421 * included %NL80211_ATTR_FRAME attribute contains the management frame
422 * (including both the header and frame body, but not FCS). This event is
423 * also used to indicate if the authentication attempt timed out. In that
424 * case the %NL80211_ATTR_FRAME attribute is replaced with a
425 * %NL80211_ATTR_TIMED_OUT flag (and %NL80211_ATTR_MAC to indicate which
426 * pending authentication timed out).
427 * @NL80211_CMD_ASSOCIATE: association request and notification; like
428 * NL80211_CMD_AUTHENTICATE but for Association and Reassociation
429 * (similar to MLME-ASSOCIATE.request, MLME-REASSOCIATE.request,
430 * MLME-ASSOCIATE.confirm or MLME-REASSOCIATE.confirm primitives).
431 * @NL80211_CMD_DEAUTHENTICATE: deauthentication request and notification; like
432 * NL80211_CMD_AUTHENTICATE but for Deauthentication frames (similar to
433 * MLME-DEAUTHENTICATION.request and MLME-DEAUTHENTICATE.indication
435 * @NL80211_CMD_DISASSOCIATE: disassociation request and notification; like
436 * NL80211_CMD_AUTHENTICATE but for Disassociation frames (similar to
437 * MLME-DISASSOCIATE.request and MLME-DISASSOCIATE.indication primitives).
439 * @NL80211_CMD_MICHAEL_MIC_FAILURE: notification of a locally detected Michael
440 * MIC (part of TKIP) failure; sent on the "mlme" multicast group; the
441 * event includes %NL80211_ATTR_MAC to describe the source MAC address of
442 * the frame with invalid MIC, %NL80211_ATTR_KEY_TYPE to show the key
443 * type, %NL80211_ATTR_KEY_IDX to indicate the key identifier, and
444 * %NL80211_ATTR_KEY_SEQ to indicate the TSC value of the frame; this
445 * event matches with MLME-MICHAELMICFAILURE.indication() primitive
447 * @NL80211_CMD_JOIN_IBSS: Join a new IBSS -- given at least an SSID and a
448 * FREQ attribute (for the initial frequency if no peer can be found)
449 * and optionally a MAC (as BSSID) and FREQ_FIXED attribute if those
450 * should be fixed rather than automatically determined. Can only be
451 * executed on a network interface that is UP, and fixed BSSID/FREQ
452 * may be rejected. Another optional parameter is the beacon interval,
453 * given in the %NL80211_ATTR_BEACON_INTERVAL attribute, which if not
454 * given defaults to 100 TU (102.4ms).
455 * @NL80211_CMD_LEAVE_IBSS: Leave the IBSS -- no special arguments, the IBSS is
456 * determined by the network interface.
458 * @NL80211_CMD_TESTMODE: testmode command, takes a wiphy (or ifindex) attribute
459 * to identify the device, and the TESTDATA blob attribute to pass through
462 * @NL80211_CMD_CONNECT: connection request and notification; this command
463 * requests to connect to a specified network but without separating
464 * auth and assoc steps. For this, you need to specify the SSID in a
465 * %NL80211_ATTR_SSID attribute, and can optionally specify the association
466 * IEs in %NL80211_ATTR_IE, %NL80211_ATTR_AUTH_TYPE, %NL80211_ATTR_USE_MFP,
467 * %NL80211_ATTR_MAC, %NL80211_ATTR_WIPHY_FREQ, %NL80211_ATTR_CONTROL_PORT,
468 * %NL80211_ATTR_CONTROL_PORT_ETHERTYPE,
469 * %NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT, %NL80211_ATTR_MAC_HINT, and
470 * %NL80211_ATTR_WIPHY_FREQ_HINT.
471 * If included, %NL80211_ATTR_MAC and %NL80211_ATTR_WIPHY_FREQ are
472 * restrictions on BSS selection, i.e., they effectively prevent roaming
473 * within the ESS. %NL80211_ATTR_MAC_HINT and %NL80211_ATTR_WIPHY_FREQ_HINT
474 * can be included to provide a recommendation of the initial BSS while
475 * allowing the driver to roam to other BSSes within the ESS and also to
476 * ignore this recommendation if the indicated BSS is not ideal. Only one
477 * set of BSSID,frequency parameters is used (i.e., either the enforcing
478 * %NL80211_ATTR_MAC,%NL80211_ATTR_WIPHY_FREQ or the less strict
479 * %NL80211_ATTR_MAC_HINT and %NL80211_ATTR_WIPHY_FREQ_HINT).
480 * Background scan period can optionally be
481 * specified in %NL80211_ATTR_BG_SCAN_PERIOD,
482 * if not specified default background scan configuration
483 * in driver is used and if period value is 0, bg scan will be disabled.
484 * This attribute is ignored if driver does not support roam scan.
485 * It is also sent as an event, with the BSSID and response IEs when the
486 * connection is established or failed to be established. This can be
487 * determined by the STATUS_CODE attribute.
488 * @NL80211_CMD_ROAM: request that the card roam (currently not implemented),
489 * sent as an event when the card/driver roamed by itself.
490 * @NL80211_CMD_DISCONNECT: drop a given connection; also used to notify
491 * userspace that a connection was dropped by the AP or due to other
492 * reasons, for this the %NL80211_ATTR_DISCONNECTED_BY_AP and
493 * %NL80211_ATTR_REASON_CODE attributes are used.
495 * @NL80211_CMD_SET_WIPHY_NETNS: Set a wiphy's netns. Note that all devices
496 * associated with this wiphy must be down and will follow.
498 * @NL80211_CMD_REMAIN_ON_CHANNEL: Request to remain awake on the specified
499 * channel for the specified amount of time. This can be used to do
500 * off-channel operations like transmit a Public Action frame and wait for
501 * a response while being associated to an AP on another channel.
502 * %NL80211_ATTR_IFINDEX is used to specify which interface (and thus
503 * radio) is used. %NL80211_ATTR_WIPHY_FREQ is used to specify the
504 * frequency for the operation.
505 * %NL80211_ATTR_DURATION is used to specify the duration in milliseconds
506 * to remain on the channel. This command is also used as an event to
507 * notify when the requested duration starts (it may take a while for the
508 * driver to schedule this time due to other concurrent needs for the
510 * When called, this operation returns a cookie (%NL80211_ATTR_COOKIE)
511 * that will be included with any events pertaining to this request;
512 * the cookie is also used to cancel the request.
513 * @NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL: This command can be used to cancel a
514 * pending remain-on-channel duration if the desired operation has been
515 * completed prior to expiration of the originally requested duration.
516 * %NL80211_ATTR_WIPHY or %NL80211_ATTR_IFINDEX is used to specify the
517 * radio. The %NL80211_ATTR_COOKIE attribute must be given as well to
518 * uniquely identify the request.
519 * This command is also used as an event to notify when a requested
520 * remain-on-channel duration has expired.
522 * @NL80211_CMD_SET_TX_BITRATE_MASK: Set the mask of rates to be used in TX
523 * rate selection. %NL80211_ATTR_IFINDEX is used to specify the interface
524 * and @NL80211_ATTR_TX_RATES the set of allowed rates.
526 * @NL80211_CMD_REGISTER_FRAME: Register for receiving certain mgmt frames
527 * (via @NL80211_CMD_FRAME) for processing in userspace. This command
528 * requires an interface index, a frame type attribute (optional for
529 * backward compatibility reasons, if not given assumes action frames)
530 * and a match attribute containing the first few bytes of the frame
531 * that should match, e.g. a single byte for only a category match or
532 * four bytes for vendor frames including the OUI. The registration
533 * cannot be dropped, but is removed automatically when the netlink
534 * socket is closed. Multiple registrations can be made.
535 * @NL80211_CMD_REGISTER_ACTION: Alias for @NL80211_CMD_REGISTER_FRAME for
536 * backward compatibility
537 * @NL80211_CMD_FRAME: Management frame TX request and RX notification. This
538 * command is used both as a request to transmit a management frame and
539 * as an event indicating reception of a frame that was not processed in
540 * kernel code, but is for us (i.e., which may need to be processed in a
541 * user space application). %NL80211_ATTR_FRAME is used to specify the
542 * frame contents (including header). %NL80211_ATTR_WIPHY_FREQ is used
543 * to indicate on which channel the frame is to be transmitted or was
544 * received. If this channel is not the current channel (remain-on-channel
545 * or the operational channel) the device will switch to the given channel
546 * and transmit the frame, optionally waiting for a response for the time
547 * specified using %NL80211_ATTR_DURATION. When called, this operation
548 * returns a cookie (%NL80211_ATTR_COOKIE) that will be included with the
549 * TX status event pertaining to the TX request.
550 * %NL80211_ATTR_TX_NO_CCK_RATE is used to decide whether to send the
551 * management frames at CCK rate or not in 2GHz band.
552 * %NL80211_ATTR_CSA_C_OFFSETS_TX is an array of offsets to CSA
553 * counters which will be updated to the current value. This attribute
554 * is used during CSA period.
555 * @NL80211_CMD_FRAME_WAIT_CANCEL: When an off-channel TX was requested, this
556 * command may be used with the corresponding cookie to cancel the wait
557 * time if it is known that it is no longer necessary.
558 * @NL80211_CMD_ACTION: Alias for @NL80211_CMD_FRAME for backward compatibility.
559 * @NL80211_CMD_FRAME_TX_STATUS: Report TX status of a management frame
560 * transmitted with %NL80211_CMD_FRAME. %NL80211_ATTR_COOKIE identifies
561 * the TX command and %NL80211_ATTR_FRAME includes the contents of the
562 * frame. %NL80211_ATTR_ACK flag is included if the recipient acknowledged
564 * @NL80211_CMD_ACTION_TX_STATUS: Alias for @NL80211_CMD_FRAME_TX_STATUS for
565 * backward compatibility.
567 * @NL80211_CMD_SET_POWER_SAVE: Set powersave, using %NL80211_ATTR_PS_STATE
568 * @NL80211_CMD_GET_POWER_SAVE: Get powersave status in %NL80211_ATTR_PS_STATE
570 * @NL80211_CMD_SET_CQM: Connection quality monitor configuration. This command
571 * is used to configure connection quality monitoring notification trigger
573 * @NL80211_CMD_NOTIFY_CQM: Connection quality monitor notification. This
574 * command is used as an event to indicate the that a trigger level was
576 * @NL80211_CMD_SET_CHANNEL: Set the channel (using %NL80211_ATTR_WIPHY_FREQ
577 * and the attributes determining channel width) the given interface
578 * (identifed by %NL80211_ATTR_IFINDEX) shall operate on.
579 * In case multiple channels are supported by the device, the mechanism
580 * with which it switches channels is implementation-defined.
581 * When a monitor interface is given, it can only switch channel while
582 * no other interfaces are operating to avoid disturbing the operation
583 * of any other interfaces, and other interfaces will again take
584 * precedence when they are used.
586 * @NL80211_CMD_SET_WDS_PEER: Set the MAC address of the peer on a WDS interface.
588 * @NL80211_CMD_JOIN_MESH: Join a mesh. The mesh ID must be given, and initial
589 * mesh config parameters may be given.
590 * @NL80211_CMD_LEAVE_MESH: Leave the mesh network -- no special arguments, the
591 * network is determined by the network interface.
593 * @NL80211_CMD_UNPROT_DEAUTHENTICATE: Unprotected deauthentication frame
594 * notification. This event is used to indicate that an unprotected
595 * deauthentication frame was dropped when MFP is in use.
596 * @NL80211_CMD_UNPROT_DISASSOCIATE: Unprotected disassociation frame
597 * notification. This event is used to indicate that an unprotected
598 * disassociation frame was dropped when MFP is in use.
600 * @NL80211_CMD_NEW_PEER_CANDIDATE: Notification on the reception of a
601 * beacon or probe response from a compatible mesh peer. This is only
602 * sent while no station information (sta_info) exists for the new peer
603 * candidate and when @NL80211_MESH_SETUP_USERSPACE_AUTH,
604 * @NL80211_MESH_SETUP_USERSPACE_AMPE, or
605 * @NL80211_MESH_SETUP_USERSPACE_MPM is set. On reception of this
606 * notification, userspace may decide to create a new station
607 * (@NL80211_CMD_NEW_STATION). To stop this notification from
608 * reoccurring, the userspace authentication daemon may want to create the
609 * new station with the AUTHENTICATED flag unset and maybe change it later
610 * depending on the authentication result.
612 * @NL80211_CMD_GET_WOWLAN: get Wake-on-Wireless-LAN (WoWLAN) settings.
613 * @NL80211_CMD_SET_WOWLAN: set Wake-on-Wireless-LAN (WoWLAN) settings.
614 * Since wireless is more complex than wired ethernet, it supports
615 * various triggers. These triggers can be configured through this
616 * command with the %NL80211_ATTR_WOWLAN_TRIGGERS attribute. For
617 * more background information, see
618 * http://wireless.kernel.org/en/users/Documentation/WoWLAN.
619 * The @NL80211_CMD_SET_WOWLAN command can also be used as a notification
620 * from the driver reporting the wakeup reason. In this case, the
621 * @NL80211_ATTR_WOWLAN_TRIGGERS attribute will contain the reason
622 * for the wakeup, if it was caused by wireless. If it is not present
623 * in the wakeup notification, the wireless device didn't cause the
624 * wakeup but reports that it was woken up.
626 * @NL80211_CMD_SET_REKEY_OFFLOAD: This command is used give the driver
627 * the necessary information for supporting GTK rekey offload. This
628 * feature is typically used during WoWLAN. The configuration data
629 * is contained in %NL80211_ATTR_REKEY_DATA (which is nested and
630 * contains the data in sub-attributes). After rekeying happened,
631 * this command may also be sent by the driver as an MLME event to
632 * inform userspace of the new replay counter.
634 * @NL80211_CMD_PMKSA_CANDIDATE: This is used as an event to inform userspace
635 * of PMKSA caching dandidates.
637 * @NL80211_CMD_TDLS_OPER: Perform a high-level TDLS command (e.g. link setup).
638 * In addition, this can be used as an event to request userspace to take
639 * actions on TDLS links (set up a new link or tear down an existing one).
640 * In such events, %NL80211_ATTR_TDLS_OPERATION indicates the requested
641 * operation, %NL80211_ATTR_MAC contains the peer MAC address, and
642 * %NL80211_ATTR_REASON_CODE the reason code to be used (only with
643 * %NL80211_TDLS_TEARDOWN).
644 * @NL80211_CMD_TDLS_MGMT: Send a TDLS management frame. The
645 * %NL80211_ATTR_TDLS_ACTION attribute determines the type of frame to be
646 * sent. Public Action codes (802.11-2012 8.1.5.1) will be sent as
647 * 802.11 management frames, while TDLS action codes (802.11-2012
648 * 8.5.13.1) will be encapsulated and sent as data frames. The currently
649 * supported Public Action code is %WLAN_PUB_ACTION_TDLS_DISCOVER_RES
650 * and the currently supported TDLS actions codes are given in
651 * &enum ieee80211_tdls_actioncode.
653 * @NL80211_CMD_UNEXPECTED_FRAME: Used by an application controlling an AP
654 * (or GO) interface (i.e. hostapd) to ask for unexpected frames to
655 * implement sending deauth to stations that send unexpected class 3
656 * frames. Also used as the event sent by the kernel when such a frame
658 * For the event, the %NL80211_ATTR_MAC attribute carries the TA and
659 * other attributes like the interface index are present.
660 * If used as the command it must have an interface index and you can
661 * only unsubscribe from the event by closing the socket. Subscription
662 * is also for %NL80211_CMD_UNEXPECTED_4ADDR_FRAME events.
664 * @NL80211_CMD_UNEXPECTED_4ADDR_FRAME: Sent as an event indicating that the
665 * associated station identified by %NL80211_ATTR_MAC sent a 4addr frame
666 * and wasn't already in a 4-addr VLAN. The event will be sent similarly
667 * to the %NL80211_CMD_UNEXPECTED_FRAME event, to the same listener.
669 * @NL80211_CMD_PROBE_CLIENT: Probe an associated station on an AP interface
670 * by sending a null data frame to it and reporting when the frame is
671 * acknowleged. This is used to allow timing out inactive clients. Uses
672 * %NL80211_ATTR_IFINDEX and %NL80211_ATTR_MAC. The command returns a
673 * direct reply with an %NL80211_ATTR_COOKIE that is later used to match
674 * up the event with the request. The event includes the same data and
675 * has %NL80211_ATTR_ACK set if the frame was ACKed.
677 * @NL80211_CMD_REGISTER_BEACONS: Register this socket to receive beacons from
678 * other BSSes when any interfaces are in AP mode. This helps implement
679 * OLBC handling in hostapd. Beacons are reported in %NL80211_CMD_FRAME
680 * messages. Note that per PHY only one application may register.
682 * @NL80211_CMD_SET_NOACK_MAP: sets a bitmap for the individual TIDs whether
683 * No Acknowledgement Policy should be applied.
685 * @NL80211_CMD_CH_SWITCH_NOTIFY: An AP or GO may decide to switch channels
686 * independently of the userspace SME, send this event indicating
687 * %NL80211_ATTR_IFINDEX is now on %NL80211_ATTR_WIPHY_FREQ and the
688 * attributes determining channel width. This indication may also be
689 * sent when a remotely-initiated switch (e.g., when a STA receives a CSA
690 * from the remote AP) is completed;
692 * @NL80211_CMD_CH_SWITCH_STARTED_NOTIFY: Notify that a channel switch
693 * has been started on an interface, regardless of the initiator
694 * (ie. whether it was requested from a remote device or
695 * initiated on our own). It indicates that
696 * %NL80211_ATTR_IFINDEX will be on %NL80211_ATTR_WIPHY_FREQ
697 * after %NL80211_ATTR_CH_SWITCH_COUNT TBTT's. The userspace may
698 * decide to react to this indication by requesting other
699 * interfaces to change channel as well.
701 * @NL80211_CMD_START_P2P_DEVICE: Start the given P2P Device, identified by
702 * its %NL80211_ATTR_WDEV identifier. It must have been created with
703 * %NL80211_CMD_NEW_INTERFACE previously. After it has been started, the
704 * P2P Device can be used for P2P operations, e.g. remain-on-channel and
705 * public action frame TX.
706 * @NL80211_CMD_STOP_P2P_DEVICE: Stop the given P2P Device, identified by
707 * its %NL80211_ATTR_WDEV identifier.
709 * @NL80211_CMD_CONN_FAILED: connection request to an AP failed; used to
710 * notify userspace that AP has rejected the connection request from a
711 * station, due to particular reason. %NL80211_ATTR_CONN_FAILED_REASON
714 * @NL80211_CMD_SET_MCAST_RATE: Change the rate used to send multicast frames
715 * for IBSS or MESH vif.
717 * @NL80211_CMD_SET_MAC_ACL: sets ACL for MAC address based access control.
718 * This is to be used with the drivers advertising the support of MAC
719 * address based access control. List of MAC addresses is passed in
720 * %NL80211_ATTR_MAC_ADDRS and ACL policy is passed in
721 * %NL80211_ATTR_ACL_POLICY. Driver will enable ACL with this list, if it
722 * is not already done. The new list will replace any existing list. Driver
723 * will clear its ACL when the list of MAC addresses passed is empty. This
724 * command is used in AP/P2P GO mode. Driver has to make sure to clear its
725 * ACL list during %NL80211_CMD_STOP_AP.
727 * @NL80211_CMD_RADAR_DETECT: Start a Channel availability check (CAC). Once
728 * a radar is detected or the channel availability scan (CAC) has finished
729 * or was aborted, or a radar was detected, usermode will be notified with
730 * this event. This command is also used to notify userspace about radars
731 * while operating on this channel.
732 * %NL80211_ATTR_RADAR_EVENT is used to inform about the type of the
735 * @NL80211_CMD_GET_PROTOCOL_FEATURES: Get global nl80211 protocol features,
736 * i.e. features for the nl80211 protocol rather than device features.
737 * Returns the features in the %NL80211_ATTR_PROTOCOL_FEATURES bitmap.
739 * @NL80211_CMD_UPDATE_FT_IES: Pass down the most up-to-date Fast Transition
740 * Information Element to the WLAN driver
742 * @NL80211_CMD_FT_EVENT: Send a Fast transition event from the WLAN driver
743 * to the supplicant. This will carry the target AP's MAC address along
744 * with the relevant Information Elements. This event is used to report
745 * received FT IEs (MDIE, FTIE, RSN IE, TIE, RICIE).
747 * @NL80211_CMD_CRIT_PROTOCOL_START: Indicates user-space will start running
748 * a critical protocol that needs more reliability in the connection to
751 * @NL80211_CMD_CRIT_PROTOCOL_STOP: Indicates the connection reliability can
752 * return back to normal.
754 * @NL80211_CMD_GET_COALESCE: Get currently supported coalesce rules.
755 * @NL80211_CMD_SET_COALESCE: Configure coalesce rules or clear existing rules.
757 * @NL80211_CMD_CHANNEL_SWITCH: Perform a channel switch by announcing the
758 * the new channel information (Channel Switch Announcement - CSA)
759 * in the beacon for some time (as defined in the
760 * %NL80211_ATTR_CH_SWITCH_COUNT parameter) and then change to the
761 * new channel. Userspace provides the new channel information (using
762 * %NL80211_ATTR_WIPHY_FREQ and the attributes determining channel
763 * width). %NL80211_ATTR_CH_SWITCH_BLOCK_TX may be supplied to inform
764 * other station that transmission must be blocked until the channel
765 * switch is complete.
767 * @NL80211_CMD_VENDOR: Vendor-specified command/event. The command is specified
768 * by the %NL80211_ATTR_VENDOR_ID attribute and a sub-command in
769 * %NL80211_ATTR_VENDOR_SUBCMD. Parameter(s) can be transported in
770 * %NL80211_ATTR_VENDOR_DATA.
771 * For feature advertisement, the %NL80211_ATTR_VENDOR_DATA attribute is
772 * used in the wiphy data as a nested attribute containing descriptions
773 * (&struct nl80211_vendor_cmd_info) of the supported vendor commands.
774 * This may also be sent as an event with the same attributes.
776 * @NL80211_CMD_SET_QOS_MAP: Set Interworking QoS mapping for IP DSCP values.
777 * The QoS mapping information is included in %NL80211_ATTR_QOS_MAP. If
778 * that attribute is not included, QoS mapping is disabled. Since this
779 * QoS mapping is relevant for IP packets, it is only valid during an
780 * association. This is cleared on disassociation and AP restart.
782 * @NL80211_CMD_ADD_TX_TS: Ask the kernel to add a traffic stream for the given
783 * %NL80211_ATTR_TSID and %NL80211_ATTR_MAC with %NL80211_ATTR_USER_PRIO
784 * and %NL80211_ATTR_ADMITTED_TIME parameters.
785 * Note that the action frame handshake with the AP shall be handled by
786 * userspace via the normal management RX/TX framework, this only sets
787 * up the TX TS in the driver/device.
788 * If the admitted time attribute is not added then the request just checks
789 * if a subsequent setup could be successful, the intent is to use this to
790 * avoid setting up a session with the AP when local restrictions would
791 * make that impossible. However, the subsequent "real" setup may still
792 * fail even if the check was successful.
793 * @NL80211_CMD_DEL_TX_TS: Remove an existing TS with the %NL80211_ATTR_TSID
794 * and %NL80211_ATTR_MAC parameters. It isn't necessary to call this
795 * before removing a station entry entirely, or before disassociating
796 * or similar, cleanup will happen in the driver/device in this case.
798 * @NL80211_CMD_GET_MPP: Get mesh path attributes for mesh proxy path to
799 * destination %NL80211_ATTR_MAC on the interface identified by
800 * %NL80211_ATTR_IFINDEX.
802 * @NL80211_CMD_JOIN_OCB: Join the OCB network. The center frequency and
803 * bandwidth of a channel must be given.
804 * @NL80211_CMD_LEAVE_OCB: Leave the OCB network -- no special arguments, the
805 * network is determined by the network interface.
807 * @NL80211_CMD_TDLS_CHANNEL_SWITCH: Start channel-switching with a TDLS peer,
808 * identified by the %NL80211_ATTR_MAC parameter. A target channel is
809 * provided via %NL80211_ATTR_WIPHY_FREQ and other attributes determining
810 * channel width/type. The target operating class is given via
811 * %NL80211_ATTR_OPER_CLASS.
812 * The driver is responsible for continually initiating channel-switching
813 * operations and returning to the base channel for communication with the
815 * @NL80211_CMD_TDLS_CANCEL_CHANNEL_SWITCH: Stop channel-switching with a TDLS
816 * peer given by %NL80211_ATTR_MAC. Both peers must be on the base channel
817 * when this command completes.
819 * @NL80211_CMD_WIPHY_REG_CHANGE: Similar to %NL80211_CMD_REG_CHANGE, but used
820 * as an event to indicate changes for devices with wiphy-specific regdom
823 * @NL80211_CMD_MAX: highest used command number
824 * @__NL80211_CMD_AFTER_LAST: internal use
826 enum nl80211_commands {
827 /* don't change the order or add anything between, this is ABI! */
830 NL80211_CMD_GET_WIPHY, /* can dump */
831 NL80211_CMD_SET_WIPHY,
832 NL80211_CMD_NEW_WIPHY,
833 NL80211_CMD_DEL_WIPHY,
835 NL80211_CMD_GET_INTERFACE, /* can dump */
836 NL80211_CMD_SET_INTERFACE,
837 NL80211_CMD_NEW_INTERFACE,
838 NL80211_CMD_DEL_INTERFACE,
845 NL80211_CMD_GET_BEACON,
846 NL80211_CMD_SET_BEACON,
847 NL80211_CMD_START_AP,
848 NL80211_CMD_NEW_BEACON = NL80211_CMD_START_AP,
850 NL80211_CMD_DEL_BEACON = NL80211_CMD_STOP_AP,
852 NL80211_CMD_GET_STATION,
853 NL80211_CMD_SET_STATION,
854 NL80211_CMD_NEW_STATION,
855 NL80211_CMD_DEL_STATION,
857 NL80211_CMD_GET_MPATH,
858 NL80211_CMD_SET_MPATH,
859 NL80211_CMD_NEW_MPATH,
860 NL80211_CMD_DEL_MPATH,
865 NL80211_CMD_REQ_SET_REG,
867 NL80211_CMD_GET_MESH_CONFIG,
868 NL80211_CMD_SET_MESH_CONFIG,
870 NL80211_CMD_SET_MGMT_EXTRA_IE /* reserved; not used */,
874 NL80211_CMD_GET_SCAN,
875 NL80211_CMD_TRIGGER_SCAN,
876 NL80211_CMD_NEW_SCAN_RESULTS,
877 NL80211_CMD_SCAN_ABORTED,
879 NL80211_CMD_REG_CHANGE,
881 NL80211_CMD_AUTHENTICATE,
882 NL80211_CMD_ASSOCIATE,
883 NL80211_CMD_DEAUTHENTICATE,
884 NL80211_CMD_DISASSOCIATE,
886 NL80211_CMD_MICHAEL_MIC_FAILURE,
888 NL80211_CMD_REG_BEACON_HINT,
890 NL80211_CMD_JOIN_IBSS,
891 NL80211_CMD_LEAVE_IBSS,
893 NL80211_CMD_TESTMODE,
897 NL80211_CMD_DISCONNECT,
899 NL80211_CMD_SET_WIPHY_NETNS,
901 NL80211_CMD_GET_SURVEY,
902 NL80211_CMD_NEW_SURVEY_RESULTS,
904 NL80211_CMD_SET_PMKSA,
905 NL80211_CMD_DEL_PMKSA,
906 NL80211_CMD_FLUSH_PMKSA,
908 NL80211_CMD_REMAIN_ON_CHANNEL,
909 NL80211_CMD_CANCEL_REMAIN_ON_CHANNEL,
911 NL80211_CMD_SET_TX_BITRATE_MASK,
913 NL80211_CMD_REGISTER_FRAME,
914 NL80211_CMD_REGISTER_ACTION = NL80211_CMD_REGISTER_FRAME,
916 NL80211_CMD_ACTION = NL80211_CMD_FRAME,
917 NL80211_CMD_FRAME_TX_STATUS,
918 NL80211_CMD_ACTION_TX_STATUS = NL80211_CMD_FRAME_TX_STATUS,
920 NL80211_CMD_SET_POWER_SAVE,
921 NL80211_CMD_GET_POWER_SAVE,
924 NL80211_CMD_NOTIFY_CQM,
926 NL80211_CMD_SET_CHANNEL,
927 NL80211_CMD_SET_WDS_PEER,
929 NL80211_CMD_FRAME_WAIT_CANCEL,
931 NL80211_CMD_JOIN_MESH,
932 NL80211_CMD_LEAVE_MESH,
934 NL80211_CMD_UNPROT_DEAUTHENTICATE,
935 NL80211_CMD_UNPROT_DISASSOCIATE,
937 NL80211_CMD_NEW_PEER_CANDIDATE,
939 NL80211_CMD_GET_WOWLAN,
940 NL80211_CMD_SET_WOWLAN,
942 NL80211_CMD_START_SCHED_SCAN,
943 NL80211_CMD_STOP_SCHED_SCAN,
944 NL80211_CMD_SCHED_SCAN_RESULTS,
945 NL80211_CMD_SCHED_SCAN_STOPPED,
947 NL80211_CMD_SET_REKEY_OFFLOAD,
949 NL80211_CMD_PMKSA_CANDIDATE,
951 NL80211_CMD_TDLS_OPER,
952 NL80211_CMD_TDLS_MGMT,
954 NL80211_CMD_UNEXPECTED_FRAME,
956 NL80211_CMD_PROBE_CLIENT,
958 NL80211_CMD_REGISTER_BEACONS,
960 NL80211_CMD_UNEXPECTED_4ADDR_FRAME,
962 NL80211_CMD_SET_NOACK_MAP,
964 NL80211_CMD_CH_SWITCH_NOTIFY,
966 NL80211_CMD_START_P2P_DEVICE,
967 NL80211_CMD_STOP_P2P_DEVICE,
969 NL80211_CMD_CONN_FAILED,
971 NL80211_CMD_SET_MCAST_RATE,
973 NL80211_CMD_SET_MAC_ACL,
975 NL80211_CMD_RADAR_DETECT,
977 NL80211_CMD_GET_PROTOCOL_FEATURES,
979 NL80211_CMD_UPDATE_FT_IES,
980 NL80211_CMD_FT_EVENT,
982 NL80211_CMD_CRIT_PROTOCOL_START,
983 NL80211_CMD_CRIT_PROTOCOL_STOP,
985 NL80211_CMD_GET_COALESCE,
986 NL80211_CMD_SET_COALESCE,
988 NL80211_CMD_CHANNEL_SWITCH,
992 NL80211_CMD_SET_QOS_MAP,
994 NL80211_CMD_ADD_TX_TS,
995 NL80211_CMD_DEL_TX_TS,
999 NL80211_CMD_JOIN_OCB,
1000 NL80211_CMD_LEAVE_OCB,
1002 NL80211_CMD_CH_SWITCH_STARTED_NOTIFY,
1004 NL80211_CMD_TDLS_CHANNEL_SWITCH,
1005 NL80211_CMD_TDLS_CANCEL_CHANNEL_SWITCH,
1007 NL80211_CMD_WIPHY_REG_CHANGE,
1009 /* add new commands above here */
1011 /* used to define NL80211_CMD_MAX below */
1012 __NL80211_CMD_AFTER_LAST,
1013 NL80211_CMD_MAX = __NL80211_CMD_AFTER_LAST - 1
1017 * Allow user space programs to use #ifdef on new commands by defining them
1020 #define NL80211_CMD_SET_BSS NL80211_CMD_SET_BSS
1021 #define NL80211_CMD_SET_MGMT_EXTRA_IE NL80211_CMD_SET_MGMT_EXTRA_IE
1022 #define NL80211_CMD_REG_CHANGE NL80211_CMD_REG_CHANGE
1023 #define NL80211_CMD_AUTHENTICATE NL80211_CMD_AUTHENTICATE
1024 #define NL80211_CMD_ASSOCIATE NL80211_CMD_ASSOCIATE
1025 #define NL80211_CMD_DEAUTHENTICATE NL80211_CMD_DEAUTHENTICATE
1026 #define NL80211_CMD_DISASSOCIATE NL80211_CMD_DISASSOCIATE
1027 #define NL80211_CMD_REG_BEACON_HINT NL80211_CMD_REG_BEACON_HINT
1029 #define NL80211_ATTR_FEATURE_FLAGS NL80211_ATTR_FEATURE_FLAGS
1031 /* source-level API compatibility */
1032 #define NL80211_CMD_GET_MESH_PARAMS NL80211_CMD_GET_MESH_CONFIG
1033 #define NL80211_CMD_SET_MESH_PARAMS NL80211_CMD_SET_MESH_CONFIG
1034 #define NL80211_MESH_SETUP_VENDOR_PATH_SEL_IE NL80211_MESH_SETUP_IE
1037 * enum nl80211_attrs - nl80211 netlink attributes
1039 * @NL80211_ATTR_UNSPEC: unspecified attribute to catch errors
1041 * @NL80211_ATTR_WIPHY: index of wiphy to operate on, cf.
1042 * /sys/class/ieee80211/<phyname>/index
1043 * @NL80211_ATTR_WIPHY_NAME: wiphy name (used for renaming)
1044 * @NL80211_ATTR_WIPHY_TXQ_PARAMS: a nested array of TX queue parameters
1045 * @NL80211_ATTR_WIPHY_FREQ: frequency of the selected channel in MHz,
1046 * defines the channel together with the (deprecated)
1047 * %NL80211_ATTR_WIPHY_CHANNEL_TYPE attribute or the attributes
1048 * %NL80211_ATTR_CHANNEL_WIDTH and if needed %NL80211_ATTR_CENTER_FREQ1
1049 * and %NL80211_ATTR_CENTER_FREQ2
1050 * @NL80211_ATTR_CHANNEL_WIDTH: u32 attribute containing one of the values
1051 * of &enum nl80211_chan_width, describing the channel width. See the
1052 * documentation of the enum for more information.
1053 * @NL80211_ATTR_CENTER_FREQ1: Center frequency of the first part of the
1054 * channel, used for anything but 20 MHz bandwidth
1055 * @NL80211_ATTR_CENTER_FREQ2: Center frequency of the second part of the
1056 * channel, used only for 80+80 MHz bandwidth
1057 * @NL80211_ATTR_WIPHY_CHANNEL_TYPE: included with NL80211_ATTR_WIPHY_FREQ
1058 * if HT20 or HT40 are to be used (i.e., HT disabled if not included):
1059 * NL80211_CHAN_NO_HT = HT not allowed (i.e., same as not including
1061 * NL80211_CHAN_HT20 = HT20 only
1062 * NL80211_CHAN_HT40MINUS = secondary channel is below the primary channel
1063 * NL80211_CHAN_HT40PLUS = secondary channel is above the primary channel
1064 * This attribute is now deprecated.
1065 * @NL80211_ATTR_WIPHY_RETRY_SHORT: TX retry limit for frames whose length is
1066 * less than or equal to the RTS threshold; allowed range: 1..255;
1067 * dot11ShortRetryLimit; u8
1068 * @NL80211_ATTR_WIPHY_RETRY_LONG: TX retry limit for frames whose length is
1069 * greater than the RTS threshold; allowed range: 1..255;
1070 * dot11ShortLongLimit; u8
1071 * @NL80211_ATTR_WIPHY_FRAG_THRESHOLD: fragmentation threshold, i.e., maximum
1072 * length in octets for frames; allowed range: 256..8000, disable
1073 * fragmentation with (u32)-1; dot11FragmentationThreshold; u32
1074 * @NL80211_ATTR_WIPHY_RTS_THRESHOLD: RTS threshold (TX frames with length
1075 * larger than or equal to this use RTS/CTS handshake); allowed range:
1076 * 0..65536, disable with (u32)-1; dot11RTSThreshold; u32
1077 * @NL80211_ATTR_WIPHY_COVERAGE_CLASS: Coverage Class as defined by IEEE 802.11
1078 * section 7.3.2.9; dot11CoverageClass; u8
1080 * @NL80211_ATTR_IFINDEX: network interface index of the device to operate on
1081 * @NL80211_ATTR_IFNAME: network interface name
1082 * @NL80211_ATTR_IFTYPE: type of virtual interface, see &enum nl80211_iftype
1084 * @NL80211_ATTR_WDEV: wireless device identifier, used for pseudo-devices
1085 * that don't have a netdev (u64)
1087 * @NL80211_ATTR_MAC: MAC address (various uses)
1089 * @NL80211_ATTR_KEY_DATA: (temporal) key data; for TKIP this consists of
1090 * 16 bytes encryption key followed by 8 bytes each for TX and RX MIC
1092 * @NL80211_ATTR_KEY_IDX: key ID (u8, 0-3)
1093 * @NL80211_ATTR_KEY_CIPHER: key cipher suite (u32, as defined by IEEE 802.11
1094 * section 7.3.2.25.1, e.g. 0x000FAC04)
1095 * @NL80211_ATTR_KEY_SEQ: transmit key sequence number (IV/PN) for TKIP and
1096 * CCMP keys, each six bytes in little endian
1097 * @NL80211_ATTR_KEY_DEFAULT: Flag attribute indicating the key is default key
1098 * @NL80211_ATTR_KEY_DEFAULT_MGMT: Flag attribute indicating the key is the
1099 * default management key
1100 * @NL80211_ATTR_CIPHER_SUITES_PAIRWISE: For crypto settings for connect or
1101 * other commands, indicates which pairwise cipher suites are used
1102 * @NL80211_ATTR_CIPHER_SUITE_GROUP: For crypto settings for connect or
1103 * other commands, indicates which group cipher suite is used
1105 * @NL80211_ATTR_BEACON_INTERVAL: beacon interval in TU
1106 * @NL80211_ATTR_DTIM_PERIOD: DTIM period for beaconing
1107 * @NL80211_ATTR_BEACON_HEAD: portion of the beacon before the TIM IE
1108 * @NL80211_ATTR_BEACON_TAIL: portion of the beacon after the TIM IE
1110 * @NL80211_ATTR_STA_AID: Association ID for the station (u16)
1111 * @NL80211_ATTR_STA_FLAGS: flags, nested element with NLA_FLAG attributes of
1112 * &enum nl80211_sta_flags (deprecated, use %NL80211_ATTR_STA_FLAGS2)
1113 * @NL80211_ATTR_STA_LISTEN_INTERVAL: listen interval as defined by
1114 * IEEE 802.11 7.3.1.6 (u16).
1115 * @NL80211_ATTR_STA_SUPPORTED_RATES: supported rates, array of supported
1116 * rates as defined by IEEE 802.11 7.3.2.2 but without the length
1117 * restriction (at most %NL80211_MAX_SUPP_RATES).
1118 * @NL80211_ATTR_STA_VLAN: interface index of VLAN interface to move station
1119 * to, or the AP interface the station was originally added to to.
1120 * @NL80211_ATTR_STA_INFO: information about a station, part of station info
1121 * given for %NL80211_CMD_GET_STATION, nested attribute containing
1122 * info as possible, see &enum nl80211_sta_info.
1124 * @NL80211_ATTR_WIPHY_BANDS: Information about an operating bands,
1125 * consisting of a nested array.
1127 * @NL80211_ATTR_MESH_ID: mesh id (1-32 bytes).
1128 * @NL80211_ATTR_STA_PLINK_ACTION: action to perform on the mesh peer link
1129 * (see &enum nl80211_plink_action).
1130 * @NL80211_ATTR_MPATH_NEXT_HOP: MAC address of the next hop for a mesh path.
1131 * @NL80211_ATTR_MPATH_INFO: information about a mesh_path, part of mesh path
1132 * info given for %NL80211_CMD_GET_MPATH, nested attribute described at
1133 * &enum nl80211_mpath_info.
1135 * @NL80211_ATTR_MNTR_FLAGS: flags, nested element with NLA_FLAG attributes of
1136 * &enum nl80211_mntr_flags.
1138 * @NL80211_ATTR_REG_ALPHA2: an ISO-3166-alpha2 country code for which the
1139 * current regulatory domain should be set to or is already set to.
1140 * For example, 'CR', for Costa Rica. This attribute is used by the kernel
1141 * to query the CRDA to retrieve one regulatory domain. This attribute can
1142 * also be used by userspace to query the kernel for the currently set
1143 * regulatory domain. We chose an alpha2 as that is also used by the
1144 * IEEE-802.11 country information element to identify a country.
1145 * Users can also simply ask the wireless core to set regulatory domain
1146 * to a specific alpha2.
1147 * @NL80211_ATTR_REG_RULES: a nested array of regulatory domain regulatory
1150 * @NL80211_ATTR_BSS_CTS_PROT: whether CTS protection is enabled (u8, 0 or 1)
1151 * @NL80211_ATTR_BSS_SHORT_PREAMBLE: whether short preamble is enabled
1153 * @NL80211_ATTR_BSS_SHORT_SLOT_TIME: whether short slot time enabled
1155 * @NL80211_ATTR_BSS_BASIC_RATES: basic rates, array of basic
1156 * rates in format defined by IEEE 802.11 7.3.2.2 but without the length
1157 * restriction (at most %NL80211_MAX_SUPP_RATES).
1159 * @NL80211_ATTR_HT_CAPABILITY: HT Capability information element (from
1160 * association request when used with NL80211_CMD_NEW_STATION)
1162 * @NL80211_ATTR_SUPPORTED_IFTYPES: nested attribute containing all
1163 * supported interface types, each a flag attribute with the number
1164 * of the interface mode.
1166 * @NL80211_ATTR_MGMT_SUBTYPE: Management frame subtype for
1167 * %NL80211_CMD_SET_MGMT_EXTRA_IE.
1169 * @NL80211_ATTR_IE: Information element(s) data (used, e.g., with
1170 * %NL80211_CMD_SET_MGMT_EXTRA_IE).
1172 * @NL80211_ATTR_MAX_NUM_SCAN_SSIDS: number of SSIDs you can scan with
1173 * a single scan request, a wiphy attribute.
1174 * @NL80211_ATTR_MAX_NUM_SCHED_SCAN_SSIDS: number of SSIDs you can
1175 * scan with a single scheduled scan request, a wiphy attribute.
1176 * @NL80211_ATTR_MAX_SCAN_IE_LEN: maximum length of information elements
1177 * that can be added to a scan request
1178 * @NL80211_ATTR_MAX_SCHED_SCAN_IE_LEN: maximum length of information
1179 * elements that can be added to a scheduled scan request
1180 * @NL80211_ATTR_MAX_MATCH_SETS: maximum number of sets that can be
1181 * used with @NL80211_ATTR_SCHED_SCAN_MATCH, a wiphy attribute.
1183 * @NL80211_ATTR_SCAN_FREQUENCIES: nested attribute with frequencies (in MHz)
1184 * @NL80211_ATTR_SCAN_SSIDS: nested attribute with SSIDs, leave out for passive
1185 * scanning and include a zero-length SSID (wildcard) for wildcard scan
1186 * @NL80211_ATTR_BSS: scan result BSS
1188 * @NL80211_ATTR_REG_INITIATOR: indicates who requested the regulatory domain
1189 * currently in effect. This could be any of the %NL80211_REGDOM_SET_BY_*
1190 * @NL80211_ATTR_REG_TYPE: indicates the type of the regulatory domain currently
1191 * set. This can be one of the nl80211_reg_type (%NL80211_REGDOM_TYPE_*)
1193 * @NL80211_ATTR_SUPPORTED_COMMANDS: wiphy attribute that specifies
1194 * an array of command numbers (i.e. a mapping index to command number)
1195 * that the driver for the given wiphy supports.
1197 * @NL80211_ATTR_FRAME: frame data (binary attribute), including frame header
1198 * and body, but not FCS; used, e.g., with NL80211_CMD_AUTHENTICATE and
1199 * NL80211_CMD_ASSOCIATE events
1200 * @NL80211_ATTR_SSID: SSID (binary attribute, 0..32 octets)
1201 * @NL80211_ATTR_AUTH_TYPE: AuthenticationType, see &enum nl80211_auth_type,
1202 * represented as a u32
1203 * @NL80211_ATTR_REASON_CODE: ReasonCode for %NL80211_CMD_DEAUTHENTICATE and
1204 * %NL80211_CMD_DISASSOCIATE, u16
1206 * @NL80211_ATTR_KEY_TYPE: Key Type, see &enum nl80211_key_type, represented as
1209 * @NL80211_ATTR_FREQ_BEFORE: A channel which has suffered a regulatory change
1210 * due to considerations from a beacon hint. This attribute reflects
1211 * the state of the channel _before_ the beacon hint processing. This
1212 * attributes consists of a nested attribute containing
1213 * NL80211_FREQUENCY_ATTR_*
1214 * @NL80211_ATTR_FREQ_AFTER: A channel which has suffered a regulatory change
1215 * due to considerations from a beacon hint. This attribute reflects
1216 * the state of the channel _after_ the beacon hint processing. This
1217 * attributes consists of a nested attribute containing
1218 * NL80211_FREQUENCY_ATTR_*
1220 * @NL80211_ATTR_CIPHER_SUITES: a set of u32 values indicating the supported
1223 * @NL80211_ATTR_FREQ_FIXED: a flag indicating the IBSS should not try to look
1224 * for other networks on different channels
1226 * @NL80211_ATTR_TIMED_OUT: a flag indicating than an operation timed out; this
1227 * is used, e.g., with %NL80211_CMD_AUTHENTICATE event
1229 * @NL80211_ATTR_USE_MFP: Whether management frame protection (IEEE 802.11w) is
1230 * used for the association (&enum nl80211_mfp, represented as a u32);
1231 * this attribute can be used
1232 * with %NL80211_CMD_ASSOCIATE and %NL80211_CMD_CONNECT requests
1234 * @NL80211_ATTR_STA_FLAGS2: Attribute containing a
1235 * &struct nl80211_sta_flag_update.
1237 * @NL80211_ATTR_CONTROL_PORT: A flag indicating whether user space controls
1238 * IEEE 802.1X port, i.e., sets/clears %NL80211_STA_FLAG_AUTHORIZED, in
1239 * station mode. If the flag is included in %NL80211_CMD_ASSOCIATE
1240 * request, the driver will assume that the port is unauthorized until
1241 * authorized by user space. Otherwise, port is marked authorized by
1242 * default in station mode.
1243 * @NL80211_ATTR_CONTROL_PORT_ETHERTYPE: A 16-bit value indicating the
1244 * ethertype that will be used for key negotiation. It can be
1245 * specified with the associate and connect commands. If it is not
1246 * specified, the value defaults to 0x888E (PAE, 802.1X). This
1247 * attribute is also used as a flag in the wiphy information to
1248 * indicate that protocols other than PAE are supported.
1249 * @NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT: When included along with
1250 * %NL80211_ATTR_CONTROL_PORT_ETHERTYPE, indicates that the custom
1251 * ethertype frames used for key negotiation must not be encrypted.
1253 * @NL80211_ATTR_TESTDATA: Testmode data blob, passed through to the driver.
1254 * We recommend using nested, driver-specific attributes within this.
1256 * @NL80211_ATTR_DISCONNECTED_BY_AP: A flag indicating that the DISCONNECT
1257 * event was due to the AP disconnecting the station, and not due to
1258 * a local disconnect request.
1259 * @NL80211_ATTR_STATUS_CODE: StatusCode for the %NL80211_CMD_CONNECT
1261 * @NL80211_ATTR_PRIVACY: Flag attribute, used with connect(), indicating
1262 * that protected APs should be used. This is also used with NEW_BEACON to
1263 * indicate that the BSS is to use protection.
1265 * @NL80211_ATTR_CIPHERS_PAIRWISE: Used with CONNECT, ASSOCIATE, and NEW_BEACON
1266 * to indicate which unicast key ciphers will be used with the connection
1267 * (an array of u32).
1268 * @NL80211_ATTR_CIPHER_GROUP: Used with CONNECT, ASSOCIATE, and NEW_BEACON to
1269 * indicate which group key cipher will be used with the connection (a
1271 * @NL80211_ATTR_WPA_VERSIONS: Used with CONNECT, ASSOCIATE, and NEW_BEACON to
1272 * indicate which WPA version(s) the AP we want to associate with is using
1273 * (a u32 with flags from &enum nl80211_wpa_versions).
1274 * @NL80211_ATTR_AKM_SUITES: Used with CONNECT, ASSOCIATE, and NEW_BEACON to
1275 * indicate which key management algorithm(s) to use (an array of u32).
1277 * @NL80211_ATTR_REQ_IE: (Re)association request information elements as
1278 * sent out by the card, for ROAM and successful CONNECT events.
1279 * @NL80211_ATTR_RESP_IE: (Re)association response information elements as
1280 * sent by peer, for ROAM and successful CONNECT events.
1282 * @NL80211_ATTR_PREV_BSSID: previous BSSID, to be used by in ASSOCIATE
1283 * commands to specify using a reassociate frame
1285 * @NL80211_ATTR_KEY: key information in a nested attribute with
1286 * %NL80211_KEY_* sub-attributes
1287 * @NL80211_ATTR_KEYS: array of keys for static WEP keys for connect()
1288 * and join_ibss(), key information is in a nested attribute each
1289 * with %NL80211_KEY_* sub-attributes
1291 * @NL80211_ATTR_PID: Process ID of a network namespace.
1293 * @NL80211_ATTR_GENERATION: Used to indicate consistent snapshots for
1294 * dumps. This number increases whenever the object list being
1295 * dumped changes, and as such userspace can verify that it has
1296 * obtained a complete and consistent snapshot by verifying that
1297 * all dump messages contain the same generation number. If it
1298 * changed then the list changed and the dump should be repeated
1299 * completely from scratch.
1301 * @NL80211_ATTR_4ADDR: Use 4-address frames on a virtual interface
1303 * @NL80211_ATTR_SURVEY_INFO: survey information about a channel, part of
1304 * the survey response for %NL80211_CMD_GET_SURVEY, nested attribute
1305 * containing info as possible, see &enum survey_info.
1307 * @NL80211_ATTR_PMKID: PMK material for PMKSA caching.
1308 * @NL80211_ATTR_MAX_NUM_PMKIDS: maximum number of PMKIDs a firmware can
1309 * cache, a wiphy attribute.
1311 * @NL80211_ATTR_DURATION: Duration of an operation in milliseconds, u32.
1312 * @NL80211_ATTR_MAX_REMAIN_ON_CHANNEL_DURATION: Device attribute that
1313 * specifies the maximum duration that can be requested with the
1314 * remain-on-channel operation, in milliseconds, u32.
1316 * @NL80211_ATTR_COOKIE: Generic 64-bit cookie to identify objects.
1318 * @NL80211_ATTR_TX_RATES: Nested set of attributes
1319 * (enum nl80211_tx_rate_attributes) describing TX rates per band. The
1320 * enum nl80211_band value is used as the index (nla_type() of the nested
1321 * data. If a band is not included, it will be configured to allow all
1322 * rates based on negotiated supported rates information. This attribute
1323 * is used with %NL80211_CMD_SET_TX_BITRATE_MASK.
1325 * @NL80211_ATTR_FRAME_MATCH: A binary attribute which typically must contain
1326 * at least one byte, currently used with @NL80211_CMD_REGISTER_FRAME.
1327 * @NL80211_ATTR_FRAME_TYPE: A u16 indicating the frame type/subtype for the
1328 * @NL80211_CMD_REGISTER_FRAME command.
1329 * @NL80211_ATTR_TX_FRAME_TYPES: wiphy capability attribute, which is a
1330 * nested attribute of %NL80211_ATTR_FRAME_TYPE attributes, containing
1331 * information about which frame types can be transmitted with
1332 * %NL80211_CMD_FRAME.
1333 * @NL80211_ATTR_RX_FRAME_TYPES: wiphy capability attribute, which is a
1334 * nested attribute of %NL80211_ATTR_FRAME_TYPE attributes, containing
1335 * information about which frame types can be registered for RX.
1337 * @NL80211_ATTR_ACK: Flag attribute indicating that the frame was
1338 * acknowledged by the recipient.
1340 * @NL80211_ATTR_PS_STATE: powersave state, using &enum nl80211_ps_state values.
1342 * @NL80211_ATTR_CQM: connection quality monitor configuration in a
1343 * nested attribute with %NL80211_ATTR_CQM_* sub-attributes.
1345 * @NL80211_ATTR_LOCAL_STATE_CHANGE: Flag attribute to indicate that a command
1346 * is requesting a local authentication/association state change without
1347 * invoking actual management frame exchange. This can be used with
1348 * NL80211_CMD_AUTHENTICATE, NL80211_CMD_DEAUTHENTICATE,
1349 * NL80211_CMD_DISASSOCIATE.
1351 * @NL80211_ATTR_AP_ISOLATE: (AP mode) Do not forward traffic between stations
1352 * connected to this BSS.
1354 * @NL80211_ATTR_WIPHY_TX_POWER_SETTING: Transmit power setting type. See
1355 * &enum nl80211_tx_power_setting for possible values.
1356 * @NL80211_ATTR_WIPHY_TX_POWER_LEVEL: Transmit power level in signed mBm units.
1357 * This is used in association with @NL80211_ATTR_WIPHY_TX_POWER_SETTING
1358 * for non-automatic settings.
1360 * @NL80211_ATTR_SUPPORT_IBSS_RSN: The device supports IBSS RSN, which mostly
1361 * means support for per-station GTKs.
1363 * @NL80211_ATTR_WIPHY_ANTENNA_TX: Bitmap of allowed antennas for transmitting.
1364 * This can be used to mask out antennas which are not attached or should
1365 * not be used for transmitting. If an antenna is not selected in this
1366 * bitmap the hardware is not allowed to transmit on this antenna.
1368 * Each bit represents one antenna, starting with antenna 1 at the first
1369 * bit. Depending on which antennas are selected in the bitmap, 802.11n
1370 * drivers can derive which chainmasks to use (if all antennas belonging to
1371 * a particular chain are disabled this chain should be disabled) and if
1372 * a chain has diversity antennas wether diversity should be used or not.
1373 * HT capabilities (STBC, TX Beamforming, Antenna selection) can be
1374 * derived from the available chains after applying the antenna mask.
1375 * Non-802.11n drivers can derive wether to use diversity or not.
1376 * Drivers may reject configurations or RX/TX mask combinations they cannot
1377 * support by returning -EINVAL.
1379 * @NL80211_ATTR_WIPHY_ANTENNA_RX: Bitmap of allowed antennas for receiving.
1380 * This can be used to mask out antennas which are not attached or should
1381 * not be used for receiving. If an antenna is not selected in this bitmap
1382 * the hardware should not be configured to receive on this antenna.
1383 * For a more detailed description see @NL80211_ATTR_WIPHY_ANTENNA_TX.
1385 * @NL80211_ATTR_WIPHY_ANTENNA_AVAIL_TX: Bitmap of antennas which are available
1386 * for configuration as TX antennas via the above parameters.
1388 * @NL80211_ATTR_WIPHY_ANTENNA_AVAIL_RX: Bitmap of antennas which are available
1389 * for configuration as RX antennas via the above parameters.
1391 * @NL80211_ATTR_MCAST_RATE: Multicast tx rate (in 100 kbps) for IBSS
1393 * @NL80211_ATTR_OFFCHANNEL_TX_OK: For management frame TX, the frame may be
1394 * transmitted on another channel when the channel given doesn't match
1395 * the current channel. If the current channel doesn't match and this
1396 * flag isn't set, the frame will be rejected. This is also used as an
1397 * nl80211 capability flag.
1399 * @NL80211_ATTR_BSS_HT_OPMODE: HT operation mode (u16)
1401 * @NL80211_ATTR_KEY_DEFAULT_TYPES: A nested attribute containing flags
1402 * attributes, specifying what a key should be set as default as.
1403 * See &enum nl80211_key_default_types.
1405 * @NL80211_ATTR_MESH_SETUP: Optional mesh setup parameters. These cannot be
1406 * changed once the mesh is active.
1407 * @NL80211_ATTR_MESH_CONFIG: Mesh configuration parameters, a nested attribute
1408 * containing attributes from &enum nl80211_meshconf_params.
1409 * @NL80211_ATTR_SUPPORT_MESH_AUTH: Currently, this means the underlying driver
1410 * allows auth frames in a mesh to be passed to userspace for processing via
1411 * the @NL80211_MESH_SETUP_USERSPACE_AUTH flag.
1412 * @NL80211_ATTR_STA_PLINK_STATE: The state of a mesh peer link as defined in
1413 * &enum nl80211_plink_state. Used when userspace is driving the peer link
1414 * management state machine. @NL80211_MESH_SETUP_USERSPACE_AMPE or
1415 * @NL80211_MESH_SETUP_USERSPACE_MPM must be enabled.
1417 * @NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED: indicates, as part of the wiphy
1418 * capabilities, the supported WoWLAN triggers
1419 * @NL80211_ATTR_WOWLAN_TRIGGERS: used by %NL80211_CMD_SET_WOWLAN to
1420 * indicate which WoW triggers should be enabled. This is also
1421 * used by %NL80211_CMD_GET_WOWLAN to get the currently enabled WoWLAN
1424 * @NL80211_ATTR_SCHED_SCAN_INTERVAL: Interval between scheduled scan
1427 * @NL80211_ATTR_SCHED_SCAN_MATCH: Nested attribute with one or more
1428 * sets of attributes to match during scheduled scans. Only BSSs
1429 * that match any of the sets will be reported. These are
1430 * pass-thru filter rules.
1431 * For a match to succeed, the BSS must match all attributes of a
1432 * set. Since not every hardware supports matching all types of
1433 * attributes, there is no guarantee that the reported BSSs are
1434 * fully complying with the match sets and userspace needs to be
1435 * able to ignore them by itself.
1436 * Thus, the implementation is somewhat hardware-dependent, but
1437 * this is only an optimization and the userspace application
1438 * needs to handle all the non-filtered results anyway.
1439 * If the match attributes don't make sense when combined with
1440 * the values passed in @NL80211_ATTR_SCAN_SSIDS (eg. if an SSID
1441 * is included in the probe request, but the match attributes
1442 * will never let it go through), -EINVAL may be returned.
1443 * If ommited, no filtering is done.
1445 * @NL80211_ATTR_INTERFACE_COMBINATIONS: Nested attribute listing the supported
1446 * interface combinations. In each nested item, it contains attributes
1447 * defined in &enum nl80211_if_combination_attrs.
1448 * @NL80211_ATTR_SOFTWARE_IFTYPES: Nested attribute (just like
1449 * %NL80211_ATTR_SUPPORTED_IFTYPES) containing the interface types that
1450 * are managed in software: interfaces of these types aren't subject to
1451 * any restrictions in their number or combinations.
1453 * @NL80211_ATTR_REKEY_DATA: nested attribute containing the information
1454 * necessary for GTK rekeying in the device, see &enum nl80211_rekey_data.
1456 * @NL80211_ATTR_SCAN_SUPP_RATES: rates per to be advertised as supported in scan,
1457 * nested array attribute containing an entry for each band, with the entry
1458 * being a list of supported rates as defined by IEEE 802.11 7.3.2.2 but
1459 * without the length restriction (at most %NL80211_MAX_SUPP_RATES).
1461 * @NL80211_ATTR_HIDDEN_SSID: indicates whether SSID is to be hidden from Beacon
1462 * and Probe Response (when response to wildcard Probe Request); see
1463 * &enum nl80211_hidden_ssid, represented as a u32
1465 * @NL80211_ATTR_IE_PROBE_RESP: Information element(s) for Probe Response frame.
1466 * This is used with %NL80211_CMD_NEW_BEACON and %NL80211_CMD_SET_BEACON to
1467 * provide extra IEs (e.g., WPS/P2P IE) into Probe Response frames when the
1468 * driver (or firmware) replies to Probe Request frames.
1469 * @NL80211_ATTR_IE_ASSOC_RESP: Information element(s) for (Re)Association
1470 * Response frames. This is used with %NL80211_CMD_NEW_BEACON and
1471 * %NL80211_CMD_SET_BEACON to provide extra IEs (e.g., WPS/P2P IE) into
1472 * (Re)Association Response frames when the driver (or firmware) replies to
1473 * (Re)Association Request frames.
1475 * @NL80211_ATTR_STA_WME: Nested attribute containing the wme configuration
1476 * of the station, see &enum nl80211_sta_wme_attr.
1477 * @NL80211_ATTR_SUPPORT_AP_UAPSD: the device supports uapsd when working
1480 * @NL80211_ATTR_ROAM_SUPPORT: Indicates whether the firmware is capable of
1481 * roaming to another AP in the same ESS if the signal lever is low.
1483 * @NL80211_ATTR_PMKSA_CANDIDATE: Nested attribute containing the PMKSA caching
1484 * candidate information, see &enum nl80211_pmksa_candidate_attr.
1486 * @NL80211_ATTR_TX_NO_CCK_RATE: Indicates whether to use CCK rate or not
1487 * for management frames transmission. In order to avoid p2p probe/action
1488 * frames are being transmitted at CCK rate in 2GHz band, the user space
1489 * applications use this attribute.
1490 * This attribute is used with %NL80211_CMD_TRIGGER_SCAN and
1491 * %NL80211_CMD_FRAME commands.
1493 * @NL80211_ATTR_TDLS_ACTION: Low level TDLS action code (e.g. link setup
1494 * request, link setup confirm, link teardown, etc.). Values are
1495 * described in the TDLS (802.11z) specification.
1496 * @NL80211_ATTR_TDLS_DIALOG_TOKEN: Non-zero token for uniquely identifying a
1497 * TDLS conversation between two devices.
1498 * @NL80211_ATTR_TDLS_OPERATION: High level TDLS operation; see
1499 * &enum nl80211_tdls_operation, represented as a u8.
1500 * @NL80211_ATTR_TDLS_SUPPORT: A flag indicating the device can operate
1501 * as a TDLS peer sta.
1502 * @NL80211_ATTR_TDLS_EXTERNAL_SETUP: The TDLS discovery/setup and teardown
1503 * procedures should be performed by sending TDLS packets via
1504 * %NL80211_CMD_TDLS_MGMT. Otherwise %NL80211_CMD_TDLS_OPER should be
1505 * used for asking the driver to perform a TDLS operation.
1507 * @NL80211_ATTR_DEVICE_AP_SME: This u32 attribute may be listed for devices
1508 * that have AP support to indicate that they have the AP SME integrated
1509 * with support for the features listed in this attribute, see
1510 * &enum nl80211_ap_sme_features.
1512 * @NL80211_ATTR_DONT_WAIT_FOR_ACK: Used with %NL80211_CMD_FRAME, this tells
1513 * the driver to not wait for an acknowledgement. Note that due to this,
1514 * it will also not give a status callback nor return a cookie. This is
1515 * mostly useful for probe responses to save airtime.
1517 * @NL80211_ATTR_FEATURE_FLAGS: This u32 attribute contains flags from
1518 * &enum nl80211_feature_flags and is advertised in wiphy information.
1519 * @NL80211_ATTR_PROBE_RESP_OFFLOAD: Indicates that the HW responds to probe
1520 * requests while operating in AP-mode.
1521 * This attribute holds a bitmap of the supported protocols for
1522 * offloading (see &enum nl80211_probe_resp_offload_support_attr).
1524 * @NL80211_ATTR_PROBE_RESP: Probe Response template data. Contains the entire
1525 * probe-response frame. The DA field in the 802.11 header is zero-ed out,
1526 * to be filled by the FW.
1527 * @NL80211_ATTR_DISABLE_HT: Force HT capable interfaces to disable
1528 * this feature. Currently, only supported in mac80211 drivers.
1529 * @NL80211_ATTR_HT_CAPABILITY_MASK: Specify which bits of the
1530 * ATTR_HT_CAPABILITY to which attention should be paid.
1531 * Currently, only mac80211 NICs support this feature.
1532 * The values that may be configured are:
1533 * MCS rates, MAX-AMSDU, HT-20-40 and HT_CAP_SGI_40
1534 * AMPDU density and AMPDU factor.
1535 * All values are treated as suggestions and may be ignored
1536 * by the driver as required. The actual values may be seen in
1537 * the station debugfs ht_caps file.
1539 * @NL80211_ATTR_DFS_REGION: region for regulatory rules which this country
1540 * abides to when initiating radiation on DFS channels. A country maps
1541 * to one DFS region.
1543 * @NL80211_ATTR_NOACK_MAP: This u16 bitmap contains the No Ack Policy of
1546 * @NL80211_ATTR_INACTIVITY_TIMEOUT: timeout value in seconds, this can be
1547 * used by the drivers which has MLME in firmware and does not have support
1548 * to report per station tx/rx activity to free up the staion entry from
1549 * the list. This needs to be used when the driver advertises the
1550 * capability to timeout the stations.
1552 * @NL80211_ATTR_RX_SIGNAL_DBM: signal strength in dBm (as a 32-bit int);
1553 * this attribute is (depending on the driver capabilities) added to
1554 * received frames indicated with %NL80211_CMD_FRAME.
1556 * @NL80211_ATTR_BG_SCAN_PERIOD: Background scan period in seconds
1557 * or 0 to disable background scan.
1559 * @NL80211_ATTR_USER_REG_HINT_TYPE: type of regulatory hint passed from
1560 * userspace. If unset it is assumed the hint comes directly from
1561 * a user. If set code could specify exactly what type of source
1562 * was used to provide the hint. For the different types of
1563 * allowed user regulatory hints see nl80211_user_reg_hint_type.
1565 * @NL80211_ATTR_CONN_FAILED_REASON: The reason for which AP has rejected
1566 * the connection request from a station. nl80211_connect_failed_reason
1567 * enum has different reasons of connection failure.
1569 * @NL80211_ATTR_SAE_DATA: SAE elements in Authentication frames. This starts
1570 * with the Authentication transaction sequence number field.
1572 * @NL80211_ATTR_VHT_CAPABILITY: VHT Capability information element (from
1573 * association request when used with NL80211_CMD_NEW_STATION)
1575 * @NL80211_ATTR_SCAN_FLAGS: scan request control flags (u32)
1577 * @NL80211_ATTR_P2P_CTWINDOW: P2P GO Client Traffic Window (u8), used with
1578 * the START_AP and SET_BSS commands
1579 * @NL80211_ATTR_P2P_OPPPS: P2P GO opportunistic PS (u8), used with the
1580 * START_AP and SET_BSS commands. This can have the values 0 or 1;
1581 * if not given in START_AP 0 is assumed, if not given in SET_BSS
1582 * no change is made.
1584 * @NL80211_ATTR_LOCAL_MESH_POWER_MODE: local mesh STA link-specific power mode
1585 * defined in &enum nl80211_mesh_power_mode.
1587 * @NL80211_ATTR_ACL_POLICY: ACL policy, see &enum nl80211_acl_policy,
1588 * carried in a u32 attribute
1590 * @NL80211_ATTR_MAC_ADDRS: Array of nested MAC addresses, used for
1593 * @NL80211_ATTR_MAC_ACL_MAX: u32 attribute to advertise the maximum
1594 * number of MAC addresses that a device can support for MAC
1597 * @NL80211_ATTR_RADAR_EVENT: Type of radar event for notification to userspace,
1598 * contains a value of enum nl80211_radar_event (u32).
1600 * @NL80211_ATTR_EXT_CAPA: 802.11 extended capabilities that the kernel driver
1601 * has and handles. The format is the same as the IE contents. See
1602 * 802.11-2012 8.4.2.29 for more information.
1603 * @NL80211_ATTR_EXT_CAPA_MASK: Extended capabilities that the kernel driver
1604 * has set in the %NL80211_ATTR_EXT_CAPA value, for multibit fields.
1606 * @NL80211_ATTR_STA_CAPABILITY: Station capabilities (u16) are advertised to
1607 * the driver, e.g., to enable TDLS power save (PU-APSD).
1609 * @NL80211_ATTR_STA_EXT_CAPABILITY: Station extended capabilities are
1610 * advertised to the driver, e.g., to enable TDLS off channel operations
1613 * @NL80211_ATTR_PROTOCOL_FEATURES: global nl80211 feature flags, see
1614 * &enum nl80211_protocol_features, the attribute is a u32.
1616 * @NL80211_ATTR_SPLIT_WIPHY_DUMP: flag attribute, userspace supports
1617 * receiving the data for a single wiphy split across multiple
1618 * messages, given with wiphy dump message
1620 * @NL80211_ATTR_MDID: Mobility Domain Identifier
1622 * @NL80211_ATTR_IE_RIC: Resource Information Container Information
1625 * @NL80211_ATTR_CRIT_PROT_ID: critical protocol identifier requiring increased
1626 * reliability, see &enum nl80211_crit_proto_id (u16).
1627 * @NL80211_ATTR_MAX_CRIT_PROT_DURATION: duration in milliseconds in which
1628 * the connection should have increased reliability (u16).
1630 * @NL80211_ATTR_PEER_AID: Association ID for the peer TDLS station (u16).
1631 * This is similar to @NL80211_ATTR_STA_AID but with a difference of being
1632 * allowed to be used with the first @NL80211_CMD_SET_STATION command to
1633 * update a TDLS peer STA entry.
1635 * @NL80211_ATTR_COALESCE_RULE: Coalesce rule information.
1637 * @NL80211_ATTR_CH_SWITCH_COUNT: u32 attribute specifying the number of TBTT's
1638 * until the channel switch event.
1639 * @NL80211_ATTR_CH_SWITCH_BLOCK_TX: flag attribute specifying that transmission
1640 * must be blocked on the current channel (before the channel switch
1642 * @NL80211_ATTR_CSA_IES: Nested set of attributes containing the IE information
1643 * for the time while performing a channel switch.
1644 * @NL80211_ATTR_CSA_C_OFF_BEACON: An array of offsets (u16) to the channel
1645 * switch counters in the beacons tail (%NL80211_ATTR_BEACON_TAIL).
1646 * @NL80211_ATTR_CSA_C_OFF_PRESP: An array of offsets (u16) to the channel
1647 * switch counters in the probe response (%NL80211_ATTR_PROBE_RESP).
1649 * @NL80211_ATTR_RXMGMT_FLAGS: flags for nl80211_send_mgmt(), u32.
1650 * As specified in the &enum nl80211_rxmgmt_flags.
1652 * @NL80211_ATTR_STA_SUPPORTED_CHANNELS: array of supported channels.
1654 * @NL80211_ATTR_STA_SUPPORTED_OPER_CLASSES: array of supported
1655 * supported operating classes.
1657 * @NL80211_ATTR_HANDLE_DFS: A flag indicating whether user space
1658 * controls DFS operation in IBSS mode. If the flag is included in
1659 * %NL80211_CMD_JOIN_IBSS request, the driver will allow use of DFS
1660 * channels and reports radar events to userspace. Userspace is required
1661 * to react to radar events, e.g. initiate a channel switch or leave the
1664 * @NL80211_ATTR_SUPPORT_5_MHZ: A flag indicating that the device supports
1665 * 5 MHz channel bandwidth.
1666 * @NL80211_ATTR_SUPPORT_10_MHZ: A flag indicating that the device supports
1667 * 10 MHz channel bandwidth.
1669 * @NL80211_ATTR_OPMODE_NOTIF: Operating mode field from Operating Mode
1670 * Notification Element based on association request when used with
1671 * %NL80211_CMD_NEW_STATION; u8 attribute.
1673 * @NL80211_ATTR_VENDOR_ID: The vendor ID, either a 24-bit OUI or, if
1674 * %NL80211_VENDOR_ID_IS_LINUX is set, a special Linux ID (not used yet)
1675 * @NL80211_ATTR_VENDOR_SUBCMD: vendor sub-command
1676 * @NL80211_ATTR_VENDOR_DATA: data for the vendor command, if any; this
1677 * attribute is also used for vendor command feature advertisement
1678 * @NL80211_ATTR_VENDOR_EVENTS: used for event list advertising in the wiphy
1679 * info, containing a nested array of possible events
1681 * @NL80211_ATTR_QOS_MAP: IP DSCP mapping for Interworking QoS mapping. This
1682 * data is in the format defined for the payload of the QoS Map Set element
1683 * in IEEE Std 802.11-2012, 8.4.2.97.
1685 * @NL80211_ATTR_MAC_HINT: MAC address recommendation as initial BSS
1686 * @NL80211_ATTR_WIPHY_FREQ_HINT: frequency of the recommended initial BSS
1688 * @NL80211_ATTR_MAX_AP_ASSOC_STA: Device attribute that indicates how many
1689 * associated stations are supported in AP mode (including P2P GO); u32.
1690 * Since drivers may not have a fixed limit on the maximum number (e.g.,
1691 * other concurrent operations may affect this), drivers are allowed to
1692 * advertise values that cannot always be met. In such cases, an attempt
1693 * to add a new station entry with @NL80211_CMD_NEW_STATION may fail.
1695 * @NL80211_ATTR_CSA_C_OFFSETS_TX: An array of csa counter offsets (u16) which
1696 * should be updated when the frame is transmitted.
1697 * @NL80211_ATTR_MAX_CSA_COUNTERS: U8 attribute used to advertise the maximum
1698 * supported number of csa counters.
1700 * @NL80211_ATTR_TDLS_PEER_CAPABILITY: flags for TDLS peer capabilities, u32.
1701 * As specified in the &enum nl80211_tdls_peer_capability.
1703 * @NL80211_ATTR_SOCKET_OWNER: Flag attribute, if set during interface
1704 * creation then the new interface will be owned by the netlink socket
1705 * that created it and will be destroyed when the socket is closed.
1706 * If set during scheduled scan start then the new scan req will be
1707 * owned by the netlink socket that created it and the scheduled scan will
1708 * be stopped when the socket is closed.
1709 * If set during configuration of regulatory indoor operation then the
1710 * regulatory indoor configuration would be owned by the netlink socket
1711 * that configured the indoor setting, and the indoor operation would be
1712 * cleared when the socket is closed.
1714 * @NL80211_ATTR_TDLS_INITIATOR: flag attribute indicating the current end is
1715 * the TDLS link initiator.
1717 * @NL80211_ATTR_USE_RRM: flag for indicating whether the current connection
1718 * shall support Radio Resource Measurements (11k). This attribute can be
1719 * used with %NL80211_CMD_ASSOCIATE and %NL80211_CMD_CONNECT requests.
1720 * User space applications are expected to use this flag only if the
1721 * underlying device supports these minimal RRM features:
1722 * %NL80211_FEATURE_DS_PARAM_SET_IE_IN_PROBES,
1723 * %NL80211_FEATURE_QUIET,
1724 * If this flag is used, driver must add the Power Capabilities IE to the
1725 * association request. In addition, it must also set the RRM capability
1726 * flag in the association request's Capability Info field.
1728 * @NL80211_ATTR_WIPHY_DYN_ACK: flag attribute used to enable ACK timeout
1729 * estimation algorithm (dynack). In order to activate dynack
1730 * %NL80211_FEATURE_ACKTO_ESTIMATION feature flag must be set by lower
1731 * drivers to indicate dynack capability. Dynack is automatically disabled
1732 * setting valid value for coverage class.
1734 * @NL80211_ATTR_TSID: a TSID value (u8 attribute)
1735 * @NL80211_ATTR_USER_PRIO: user priority value (u8 attribute)
1736 * @NL80211_ATTR_ADMITTED_TIME: admitted time in units of 32 microseconds
1737 * (per second) (u16 attribute)
1739 * @NL80211_ATTR_SMPS_MODE: SMPS mode to use (ap mode). see
1740 * &enum nl80211_smps_mode.
1742 * @NL80211_ATTR_OPER_CLASS: operating class
1744 * @NL80211_ATTR_MAC_MASK: MAC address mask
1746 * @NL80211_ATTR_WIPHY_SELF_MANAGED_REG: flag attribute indicating this device
1747 * is self-managing its regulatory information and any regulatory domain
1748 * obtained from it is coming from the device's wiphy and not the global
1749 * cfg80211 regdomain.
1751 * @NL80211_ATTR_EXT_FEATURES: extended feature flags contained in a byte
1752 * array. The feature flags are identified by their bit index (see &enum
1753 * nl80211_ext_feature_index). The bit index is ordered starting at the
1754 * least-significant bit of the first byte in the array, ie. bit index 0
1755 * is located at bit 0 of byte 0. bit index 25 would be located at bit 1
1756 * of byte 3 (u8 array).
1758 * @NL80211_ATTR_SURVEY_RADIO_STATS: Request overall radio statistics to be
1759 * returned along with other survey data. If set, @NL80211_CMD_GET_SURVEY
1760 * may return a survey entry without a channel indicating global radio
1761 * statistics (only some values are valid and make sense.)
1762 * For devices that don't return such an entry even then, the information
1763 * should be contained in the result as the sum of the respective counters
1764 * over all channels.
1766 * @NL80211_ATTR_SCHED_SCAN_DELAY: delay before the first cycle of a
1767 * scheduled scan (or a WoWLAN net-detect scan) is started, u32
1770 * @NL80211_ATTR_REG_INDOOR: flag attribute, if set indicates that the device
1771 * is operating in an indoor environment.
1773 * @NL80211_ATTR_MAX_NUM_SCHED_SCAN_PLANS: maximum number of scan plans for
1774 * scheduled scan supported by the device (u32), a wiphy attribute.
1775 * @NL80211_ATTR_MAX_SCAN_PLAN_INTERVAL: maximum interval (in seconds) for
1776 * a scan plan (u32), a wiphy attribute.
1777 * @NL80211_ATTR_MAX_SCAN_PLAN_ITERATIONS: maximum number of iterations in
1778 * a scan plan (u32), a wiphy attribute.
1779 * @NL80211_ATTR_SCHED_SCAN_PLANS: a list of scan plans for scheduled scan.
1780 * Each scan plan defines the number of scan iterations and the interval
1781 * between scans. The last scan plan will always run infinitely,
1782 * thus it must not specify the number of iterations, only the interval
1783 * between scans. The scan plans are executed sequentially.
1784 * Each scan plan is a nested attribute of &enum nl80211_sched_scan_plan.
1786 * @NUM_NL80211_ATTR: total number of nl80211_attrs available
1787 * @NL80211_ATTR_MAX: highest attribute number currently defined
1788 * @__NL80211_ATTR_AFTER_LAST: internal use
1790 enum nl80211_attrs {
1791 /* don't change the order or add anything between, this is ABI! */
1792 NL80211_ATTR_UNSPEC,
1795 NL80211_ATTR_WIPHY_NAME,
1797 NL80211_ATTR_IFINDEX,
1798 NL80211_ATTR_IFNAME,
1799 NL80211_ATTR_IFTYPE,
1803 NL80211_ATTR_KEY_DATA,
1804 NL80211_ATTR_KEY_IDX,
1805 NL80211_ATTR_KEY_CIPHER,
1806 NL80211_ATTR_KEY_SEQ,
1807 NL80211_ATTR_KEY_DEFAULT,
1809 NL80211_ATTR_BEACON_INTERVAL,
1810 NL80211_ATTR_DTIM_PERIOD,
1811 NL80211_ATTR_BEACON_HEAD,
1812 NL80211_ATTR_BEACON_TAIL,
1814 NL80211_ATTR_STA_AID,
1815 NL80211_ATTR_STA_FLAGS,
1816 NL80211_ATTR_STA_LISTEN_INTERVAL,
1817 NL80211_ATTR_STA_SUPPORTED_RATES,
1818 NL80211_ATTR_STA_VLAN,
1819 NL80211_ATTR_STA_INFO,
1821 NL80211_ATTR_WIPHY_BANDS,
1823 NL80211_ATTR_MNTR_FLAGS,
1825 NL80211_ATTR_MESH_ID,
1826 NL80211_ATTR_STA_PLINK_ACTION,
1827 NL80211_ATTR_MPATH_NEXT_HOP,
1828 NL80211_ATTR_MPATH_INFO,
1830 NL80211_ATTR_BSS_CTS_PROT,
1831 NL80211_ATTR_BSS_SHORT_PREAMBLE,
1832 NL80211_ATTR_BSS_SHORT_SLOT_TIME,
1834 NL80211_ATTR_HT_CAPABILITY,
1836 NL80211_ATTR_SUPPORTED_IFTYPES,
1838 NL80211_ATTR_REG_ALPHA2,
1839 NL80211_ATTR_REG_RULES,
1841 NL80211_ATTR_MESH_CONFIG,
1843 NL80211_ATTR_BSS_BASIC_RATES,
1845 NL80211_ATTR_WIPHY_TXQ_PARAMS,
1846 NL80211_ATTR_WIPHY_FREQ,
1847 NL80211_ATTR_WIPHY_CHANNEL_TYPE,
1849 NL80211_ATTR_KEY_DEFAULT_MGMT,
1851 NL80211_ATTR_MGMT_SUBTYPE,
1854 NL80211_ATTR_MAX_NUM_SCAN_SSIDS,
1856 NL80211_ATTR_SCAN_FREQUENCIES,
1857 NL80211_ATTR_SCAN_SSIDS,
1858 NL80211_ATTR_GENERATION, /* replaces old SCAN_GENERATION */
1861 NL80211_ATTR_REG_INITIATOR,
1862 NL80211_ATTR_REG_TYPE,
1864 NL80211_ATTR_SUPPORTED_COMMANDS,
1868 NL80211_ATTR_AUTH_TYPE,
1869 NL80211_ATTR_REASON_CODE,
1871 NL80211_ATTR_KEY_TYPE,
1873 NL80211_ATTR_MAX_SCAN_IE_LEN,
1874 NL80211_ATTR_CIPHER_SUITES,
1876 NL80211_ATTR_FREQ_BEFORE,
1877 NL80211_ATTR_FREQ_AFTER,
1879 NL80211_ATTR_FREQ_FIXED,
1882 NL80211_ATTR_WIPHY_RETRY_SHORT,
1883 NL80211_ATTR_WIPHY_RETRY_LONG,
1884 NL80211_ATTR_WIPHY_FRAG_THRESHOLD,
1885 NL80211_ATTR_WIPHY_RTS_THRESHOLD,
1887 NL80211_ATTR_TIMED_OUT,
1889 NL80211_ATTR_USE_MFP,
1891 NL80211_ATTR_STA_FLAGS2,
1893 NL80211_ATTR_CONTROL_PORT,
1895 NL80211_ATTR_TESTDATA,
1897 NL80211_ATTR_PRIVACY,
1899 NL80211_ATTR_DISCONNECTED_BY_AP,
1900 NL80211_ATTR_STATUS_CODE,
1902 NL80211_ATTR_CIPHER_SUITES_PAIRWISE,
1903 NL80211_ATTR_CIPHER_SUITE_GROUP,
1904 NL80211_ATTR_WPA_VERSIONS,
1905 NL80211_ATTR_AKM_SUITES,
1907 NL80211_ATTR_REQ_IE,
1908 NL80211_ATTR_RESP_IE,
1910 NL80211_ATTR_PREV_BSSID,
1919 NL80211_ATTR_SURVEY_INFO,
1922 NL80211_ATTR_MAX_NUM_PMKIDS,
1924 NL80211_ATTR_DURATION,
1926 NL80211_ATTR_COOKIE,
1928 NL80211_ATTR_WIPHY_COVERAGE_CLASS,
1930 NL80211_ATTR_TX_RATES,
1932 NL80211_ATTR_FRAME_MATCH,
1936 NL80211_ATTR_PS_STATE,
1940 NL80211_ATTR_LOCAL_STATE_CHANGE,
1942 NL80211_ATTR_AP_ISOLATE,
1944 NL80211_ATTR_WIPHY_TX_POWER_SETTING,
1945 NL80211_ATTR_WIPHY_TX_POWER_LEVEL,
1947 NL80211_ATTR_TX_FRAME_TYPES,
1948 NL80211_ATTR_RX_FRAME_TYPES,
1949 NL80211_ATTR_FRAME_TYPE,
1951 NL80211_ATTR_CONTROL_PORT_ETHERTYPE,
1952 NL80211_ATTR_CONTROL_PORT_NO_ENCRYPT,
1954 NL80211_ATTR_SUPPORT_IBSS_RSN,
1956 NL80211_ATTR_WIPHY_ANTENNA_TX,
1957 NL80211_ATTR_WIPHY_ANTENNA_RX,
1959 NL80211_ATTR_MCAST_RATE,
1961 NL80211_ATTR_OFFCHANNEL_TX_OK,
1963 NL80211_ATTR_BSS_HT_OPMODE,
1965 NL80211_ATTR_KEY_DEFAULT_TYPES,
1967 NL80211_ATTR_MAX_REMAIN_ON_CHANNEL_DURATION,
1969 NL80211_ATTR_MESH_SETUP,
1971 NL80211_ATTR_WIPHY_ANTENNA_AVAIL_TX,
1972 NL80211_ATTR_WIPHY_ANTENNA_AVAIL_RX,
1974 NL80211_ATTR_SUPPORT_MESH_AUTH,
1975 NL80211_ATTR_STA_PLINK_STATE,
1977 NL80211_ATTR_WOWLAN_TRIGGERS,
1978 NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED,
1980 NL80211_ATTR_SCHED_SCAN_INTERVAL,
1982 NL80211_ATTR_INTERFACE_COMBINATIONS,
1983 NL80211_ATTR_SOFTWARE_IFTYPES,
1985 NL80211_ATTR_REKEY_DATA,
1987 NL80211_ATTR_MAX_NUM_SCHED_SCAN_SSIDS,
1988 NL80211_ATTR_MAX_SCHED_SCAN_IE_LEN,
1990 NL80211_ATTR_SCAN_SUPP_RATES,
1992 NL80211_ATTR_HIDDEN_SSID,
1994 NL80211_ATTR_IE_PROBE_RESP,
1995 NL80211_ATTR_IE_ASSOC_RESP,
1997 NL80211_ATTR_STA_WME,
1998 NL80211_ATTR_SUPPORT_AP_UAPSD,
2000 NL80211_ATTR_ROAM_SUPPORT,
2002 NL80211_ATTR_SCHED_SCAN_MATCH,
2003 NL80211_ATTR_MAX_MATCH_SETS,
2005 NL80211_ATTR_PMKSA_CANDIDATE,
2007 NL80211_ATTR_TX_NO_CCK_RATE,
2009 NL80211_ATTR_TDLS_ACTION,
2010 NL80211_ATTR_TDLS_DIALOG_TOKEN,
2011 NL80211_ATTR_TDLS_OPERATION,
2012 NL80211_ATTR_TDLS_SUPPORT,
2013 NL80211_ATTR_TDLS_EXTERNAL_SETUP,
2015 NL80211_ATTR_DEVICE_AP_SME,
2017 NL80211_ATTR_DONT_WAIT_FOR_ACK,
2019 NL80211_ATTR_FEATURE_FLAGS,
2021 NL80211_ATTR_PROBE_RESP_OFFLOAD,
2023 NL80211_ATTR_PROBE_RESP,
2025 NL80211_ATTR_DFS_REGION,
2027 NL80211_ATTR_DISABLE_HT,
2028 NL80211_ATTR_HT_CAPABILITY_MASK,
2030 NL80211_ATTR_NOACK_MAP,
2032 NL80211_ATTR_INACTIVITY_TIMEOUT,
2034 NL80211_ATTR_RX_SIGNAL_DBM,
2036 NL80211_ATTR_BG_SCAN_PERIOD,
2040 NL80211_ATTR_USER_REG_HINT_TYPE,
2042 NL80211_ATTR_CONN_FAILED_REASON,
2044 NL80211_ATTR_SAE_DATA,
2046 NL80211_ATTR_VHT_CAPABILITY,
2048 NL80211_ATTR_SCAN_FLAGS,
2050 NL80211_ATTR_CHANNEL_WIDTH,
2051 NL80211_ATTR_CENTER_FREQ1,
2052 NL80211_ATTR_CENTER_FREQ2,
2054 NL80211_ATTR_P2P_CTWINDOW,
2055 NL80211_ATTR_P2P_OPPPS,
2057 NL80211_ATTR_LOCAL_MESH_POWER_MODE,
2059 NL80211_ATTR_ACL_POLICY,
2061 NL80211_ATTR_MAC_ADDRS,
2063 NL80211_ATTR_MAC_ACL_MAX,
2065 NL80211_ATTR_RADAR_EVENT,
2067 NL80211_ATTR_EXT_CAPA,
2068 NL80211_ATTR_EXT_CAPA_MASK,
2070 NL80211_ATTR_STA_CAPABILITY,
2071 NL80211_ATTR_STA_EXT_CAPABILITY,
2073 NL80211_ATTR_PROTOCOL_FEATURES,
2074 NL80211_ATTR_SPLIT_WIPHY_DUMP,
2076 NL80211_ATTR_DISABLE_VHT,
2077 NL80211_ATTR_VHT_CAPABILITY_MASK,
2080 NL80211_ATTR_IE_RIC,
2082 NL80211_ATTR_CRIT_PROT_ID,
2083 NL80211_ATTR_MAX_CRIT_PROT_DURATION,
2085 NL80211_ATTR_PEER_AID,
2087 NL80211_ATTR_COALESCE_RULE,
2089 NL80211_ATTR_CH_SWITCH_COUNT,
2090 NL80211_ATTR_CH_SWITCH_BLOCK_TX,
2091 NL80211_ATTR_CSA_IES,
2092 NL80211_ATTR_CSA_C_OFF_BEACON,
2093 NL80211_ATTR_CSA_C_OFF_PRESP,
2095 NL80211_ATTR_RXMGMT_FLAGS,
2097 NL80211_ATTR_STA_SUPPORTED_CHANNELS,
2099 NL80211_ATTR_STA_SUPPORTED_OPER_CLASSES,
2101 NL80211_ATTR_HANDLE_DFS,
2103 NL80211_ATTR_SUPPORT_5_MHZ,
2104 NL80211_ATTR_SUPPORT_10_MHZ,
2106 NL80211_ATTR_OPMODE_NOTIF,
2108 NL80211_ATTR_VENDOR_ID,
2109 NL80211_ATTR_VENDOR_SUBCMD,
2110 NL80211_ATTR_VENDOR_DATA,
2111 NL80211_ATTR_VENDOR_EVENTS,
2113 NL80211_ATTR_QOS_MAP,
2115 NL80211_ATTR_MAC_HINT,
2116 NL80211_ATTR_WIPHY_FREQ_HINT,
2118 NL80211_ATTR_MAX_AP_ASSOC_STA,
2120 NL80211_ATTR_TDLS_PEER_CAPABILITY,
2122 NL80211_ATTR_SOCKET_OWNER,
2124 NL80211_ATTR_CSA_C_OFFSETS_TX,
2125 NL80211_ATTR_MAX_CSA_COUNTERS,
2127 NL80211_ATTR_TDLS_INITIATOR,
2129 NL80211_ATTR_USE_RRM,
2131 NL80211_ATTR_WIPHY_DYN_ACK,
2134 NL80211_ATTR_USER_PRIO,
2135 NL80211_ATTR_ADMITTED_TIME,
2137 NL80211_ATTR_SMPS_MODE,
2139 NL80211_ATTR_OPER_CLASS,
2141 NL80211_ATTR_MAC_MASK,
2143 NL80211_ATTR_WIPHY_SELF_MANAGED_REG,
2145 NL80211_ATTR_EXT_FEATURES,
2147 NL80211_ATTR_SURVEY_RADIO_STATS,
2149 NL80211_ATTR_NETNS_FD,
2151 NL80211_ATTR_SCHED_SCAN_DELAY,
2153 NL80211_ATTR_REG_INDOOR,
2155 NL80211_ATTR_MAX_NUM_SCHED_SCAN_PLANS,
2156 NL80211_ATTR_MAX_SCAN_PLAN_INTERVAL,
2157 NL80211_ATTR_MAX_SCAN_PLAN_ITERATIONS,
2158 NL80211_ATTR_SCHED_SCAN_PLANS,
2160 /* add attributes here, update the policy in nl80211.c */
2162 __NL80211_ATTR_AFTER_LAST,
2163 NUM_NL80211_ATTR = __NL80211_ATTR_AFTER_LAST,
2164 NL80211_ATTR_MAX = __NL80211_ATTR_AFTER_LAST - 1
2167 /* source-level API compatibility */
2168 #define NL80211_ATTR_SCAN_GENERATION NL80211_ATTR_GENERATION
2169 #define NL80211_ATTR_MESH_PARAMS NL80211_ATTR_MESH_CONFIG
2170 #define NL80211_ATTR_IFACE_SOCKET_OWNER NL80211_ATTR_SOCKET_OWNER
2173 * Allow user space programs to use #ifdef on new attributes by defining them
2176 #define NL80211_CMD_CONNECT NL80211_CMD_CONNECT
2177 #define NL80211_ATTR_HT_CAPABILITY NL80211_ATTR_HT_CAPABILITY
2178 #define NL80211_ATTR_BSS_BASIC_RATES NL80211_ATTR_BSS_BASIC_RATES
2179 #define NL80211_ATTR_WIPHY_TXQ_PARAMS NL80211_ATTR_WIPHY_TXQ_PARAMS
2180 #define NL80211_ATTR_WIPHY_FREQ NL80211_ATTR_WIPHY_FREQ
2181 #define NL80211_ATTR_WIPHY_CHANNEL_TYPE NL80211_ATTR_WIPHY_CHANNEL_TYPE
2182 #define NL80211_ATTR_MGMT_SUBTYPE NL80211_ATTR_MGMT_SUBTYPE
2183 #define NL80211_ATTR_IE NL80211_ATTR_IE
2184 #define NL80211_ATTR_REG_INITIATOR NL80211_ATTR_REG_INITIATOR
2185 #define NL80211_ATTR_REG_TYPE NL80211_ATTR_REG_TYPE
2186 #define NL80211_ATTR_FRAME NL80211_ATTR_FRAME
2187 #define NL80211_ATTR_SSID NL80211_ATTR_SSID
2188 #define NL80211_ATTR_AUTH_TYPE NL80211_ATTR_AUTH_TYPE
2189 #define NL80211_ATTR_REASON_CODE NL80211_ATTR_REASON_CODE
2190 #define NL80211_ATTR_CIPHER_SUITES_PAIRWISE NL80211_ATTR_CIPHER_SUITES_PAIRWISE
2191 #define NL80211_ATTR_CIPHER_SUITE_GROUP NL80211_ATTR_CIPHER_SUITE_GROUP
2192 #define NL80211_ATTR_WPA_VERSIONS NL80211_ATTR_WPA_VERSIONS
2193 #define NL80211_ATTR_AKM_SUITES NL80211_ATTR_AKM_SUITES
2194 #define NL80211_ATTR_KEY NL80211_ATTR_KEY
2195 #define NL80211_ATTR_KEYS NL80211_ATTR_KEYS
2196 #define NL80211_ATTR_FEATURE_FLAGS NL80211_ATTR_FEATURE_FLAGS
2198 #define NL80211_WIPHY_NAME_MAXLEN 64
2200 #define NL80211_MAX_SUPP_RATES 32
2201 #define NL80211_MAX_SUPP_HT_RATES 77
2202 #define NL80211_MAX_SUPP_REG_RULES 64
2203 #define NL80211_TKIP_DATA_OFFSET_ENCR_KEY 0
2204 #define NL80211_TKIP_DATA_OFFSET_TX_MIC_KEY 16
2205 #define NL80211_TKIP_DATA_OFFSET_RX_MIC_KEY 24
2206 #define NL80211_HT_CAPABILITY_LEN 26
2207 #define NL80211_VHT_CAPABILITY_LEN 12
2209 #define NL80211_MAX_NR_CIPHER_SUITES 5
2210 #define NL80211_MAX_NR_AKM_SUITES 2
2212 #define NL80211_MIN_REMAIN_ON_CHANNEL_TIME 10
2214 /* default RSSI threshold for scan results if none specified. */
2215 #define NL80211_SCAN_RSSI_THOLD_OFF -300
2217 #define NL80211_CQM_TXE_MAX_INTVL 1800
2220 * enum nl80211_iftype - (virtual) interface types
2222 * @NL80211_IFTYPE_UNSPECIFIED: unspecified type, driver decides
2223 * @NL80211_IFTYPE_ADHOC: independent BSS member
2224 * @NL80211_IFTYPE_STATION: managed BSS member
2225 * @NL80211_IFTYPE_AP: access point
2226 * @NL80211_IFTYPE_AP_VLAN: VLAN interface for access points; VLAN interfaces
2227 * are a bit special in that they must always be tied to a pre-existing
2228 * AP type interface.
2229 * @NL80211_IFTYPE_WDS: wireless distribution interface
2230 * @NL80211_IFTYPE_MONITOR: monitor interface receiving all frames
2231 * @NL80211_IFTYPE_MESH_POINT: mesh point
2232 * @NL80211_IFTYPE_P2P_CLIENT: P2P client
2233 * @NL80211_IFTYPE_P2P_GO: P2P group owner
2234 * @NL80211_IFTYPE_P2P_DEVICE: P2P device interface type, this is not a netdev
2235 * and therefore can't be created in the normal ways, use the
2236 * %NL80211_CMD_START_P2P_DEVICE and %NL80211_CMD_STOP_P2P_DEVICE
2237 * commands to create and destroy one
2238 * @NL80211_IF_TYPE_OCB: Outside Context of a BSS
2239 * This mode corresponds to the MIB variable dot11OCBActivated=true
2240 * @NL80211_IFTYPE_MAX: highest interface type number currently defined
2241 * @NUM_NL80211_IFTYPES: number of defined interface types
2243 * These values are used with the %NL80211_ATTR_IFTYPE
2244 * to set the type of an interface.
2247 enum nl80211_iftype {
2248 NL80211_IFTYPE_UNSPECIFIED,
2249 NL80211_IFTYPE_ADHOC,
2250 NL80211_IFTYPE_STATION,
2252 NL80211_IFTYPE_AP_VLAN,
2254 NL80211_IFTYPE_MONITOR,
2255 NL80211_IFTYPE_MESH_POINT,
2256 NL80211_IFTYPE_P2P_CLIENT,
2257 NL80211_IFTYPE_P2P_GO,
2258 NL80211_IFTYPE_P2P_DEVICE,
2262 NUM_NL80211_IFTYPES,
2263 NL80211_IFTYPE_MAX = NUM_NL80211_IFTYPES - 1
2267 * enum nl80211_sta_flags - station flags
2269 * Station flags. When a station is added to an AP interface, it is
2270 * assumed to be already associated (and hence authenticated.)
2272 * @__NL80211_STA_FLAG_INVALID: attribute number 0 is reserved
2273 * @NL80211_STA_FLAG_AUTHORIZED: station is authorized (802.1X)
2274 * @NL80211_STA_FLAG_SHORT_PREAMBLE: station is capable of receiving frames
2275 * with short barker preamble
2276 * @NL80211_STA_FLAG_WME: station is WME/QoS capable
2277 * @NL80211_STA_FLAG_MFP: station uses management frame protection
2278 * @NL80211_STA_FLAG_AUTHENTICATED: station is authenticated
2279 * @NL80211_STA_FLAG_TDLS_PEER: station is a TDLS peer -- this flag should
2280 * only be used in managed mode (even in the flags mask). Note that the
2281 * flag can't be changed, it is only valid while adding a station, and
2282 * attempts to change it will silently be ignored (rather than rejected
2284 * @NL80211_STA_FLAG_ASSOCIATED: station is associated; used with drivers
2285 * that support %NL80211_FEATURE_FULL_AP_CLIENT_STATE to transition a
2286 * previously added station into associated state
2287 * @NL80211_STA_FLAG_MAX: highest station flag number currently defined
2288 * @__NL80211_STA_FLAG_AFTER_LAST: internal use
2290 enum nl80211_sta_flags {
2291 __NL80211_STA_FLAG_INVALID,
2292 NL80211_STA_FLAG_AUTHORIZED,
2293 NL80211_STA_FLAG_SHORT_PREAMBLE,
2294 NL80211_STA_FLAG_WME,
2295 NL80211_STA_FLAG_MFP,
2296 NL80211_STA_FLAG_AUTHENTICATED,
2297 NL80211_STA_FLAG_TDLS_PEER,
2298 NL80211_STA_FLAG_ASSOCIATED,
2301 __NL80211_STA_FLAG_AFTER_LAST,
2302 NL80211_STA_FLAG_MAX = __NL80211_STA_FLAG_AFTER_LAST - 1
2305 #define NL80211_STA_FLAG_MAX_OLD_API NL80211_STA_FLAG_TDLS_PEER
2308 * struct nl80211_sta_flag_update - station flags mask/set
2309 * @mask: mask of station flags to set
2310 * @set: which values to set them to
2312 * Both mask and set contain bits as per &enum nl80211_sta_flags.
2314 struct nl80211_sta_flag_update {
2317 } __attribute__((packed));
2320 * enum nl80211_rate_info - bitrate information
2322 * These attribute types are used with %NL80211_STA_INFO_TXRATE
2323 * when getting information about the bitrate of a station.
2324 * There are 2 attributes for bitrate, a legacy one that represents
2325 * a 16-bit value, and new one that represents a 32-bit value.
2326 * If the rate value fits into 16 bit, both attributes are reported
2327 * with the same value. If the rate is too high to fit into 16 bits
2328 * (>6.5535Gbps) only 32-bit attribute is included.
2329 * User space tools encouraged to use the 32-bit attribute and fall
2330 * back to the 16-bit one for compatibility with older kernels.
2332 * @__NL80211_RATE_INFO_INVALID: attribute number 0 is reserved
2333 * @NL80211_RATE_INFO_BITRATE: total bitrate (u16, 100kbit/s)
2334 * @NL80211_RATE_INFO_MCS: mcs index for 802.11n (u8)
2335 * @NL80211_RATE_INFO_40_MHZ_WIDTH: 40 MHz dualchannel bitrate
2336 * @NL80211_RATE_INFO_SHORT_GI: 400ns guard interval
2337 * @NL80211_RATE_INFO_BITRATE32: total bitrate (u32, 100kbit/s)
2338 * @NL80211_RATE_INFO_MAX: highest rate_info number currently defined
2339 * @NL80211_RATE_INFO_VHT_MCS: MCS index for VHT (u8)
2340 * @NL80211_RATE_INFO_VHT_NSS: number of streams in VHT (u8)
2341 * @NL80211_RATE_INFO_80_MHZ_WIDTH: 80 MHz VHT rate
2342 * @NL80211_RATE_INFO_80P80_MHZ_WIDTH: unused - 80+80 is treated the
2343 * same as 160 for purposes of the bitrates
2344 * @NL80211_RATE_INFO_160_MHZ_WIDTH: 160 MHz VHT rate
2345 * @NL80211_RATE_INFO_10_MHZ_WIDTH: 10 MHz width - note that this is
2346 * a legacy rate and will be reported as the actual bitrate, i.e.
2347 * half the base (20 MHz) rate
2348 * @NL80211_RATE_INFO_5_MHZ_WIDTH: 5 MHz width - note that this is
2349 * a legacy rate and will be reported as the actual bitrate, i.e.
2350 * a quarter of the base (20 MHz) rate
2351 * @__NL80211_RATE_INFO_AFTER_LAST: internal use
2353 enum nl80211_rate_info {
2354 __NL80211_RATE_INFO_INVALID,
2355 NL80211_RATE_INFO_BITRATE,
2356 NL80211_RATE_INFO_MCS,
2357 NL80211_RATE_INFO_40_MHZ_WIDTH,
2358 NL80211_RATE_INFO_SHORT_GI,
2359 NL80211_RATE_INFO_BITRATE32,
2360 NL80211_RATE_INFO_VHT_MCS,
2361 NL80211_RATE_INFO_VHT_NSS,
2362 NL80211_RATE_INFO_80_MHZ_WIDTH,
2363 NL80211_RATE_INFO_80P80_MHZ_WIDTH,
2364 NL80211_RATE_INFO_160_MHZ_WIDTH,
2365 NL80211_RATE_INFO_10_MHZ_WIDTH,
2366 NL80211_RATE_INFO_5_MHZ_WIDTH,
2369 __NL80211_RATE_INFO_AFTER_LAST,
2370 NL80211_RATE_INFO_MAX = __NL80211_RATE_INFO_AFTER_LAST - 1
2374 * enum nl80211_sta_bss_param - BSS information collected by STA
2376 * These attribute types are used with %NL80211_STA_INFO_BSS_PARAM
2377 * when getting information about the bitrate of a station.
2379 * @__NL80211_STA_BSS_PARAM_INVALID: attribute number 0 is reserved
2380 * @NL80211_STA_BSS_PARAM_CTS_PROT: whether CTS protection is enabled (flag)
2381 * @NL80211_STA_BSS_PARAM_SHORT_PREAMBLE: whether short preamble is enabled
2383 * @NL80211_STA_BSS_PARAM_SHORT_SLOT_TIME: whether short slot time is enabled
2385 * @NL80211_STA_BSS_PARAM_DTIM_PERIOD: DTIM period for beaconing (u8)
2386 * @NL80211_STA_BSS_PARAM_BEACON_INTERVAL: Beacon interval (u16)
2387 * @NL80211_STA_BSS_PARAM_MAX: highest sta_bss_param number currently defined
2388 * @__NL80211_STA_BSS_PARAM_AFTER_LAST: internal use
2390 enum nl80211_sta_bss_param {
2391 __NL80211_STA_BSS_PARAM_INVALID,
2392 NL80211_STA_BSS_PARAM_CTS_PROT,
2393 NL80211_STA_BSS_PARAM_SHORT_PREAMBLE,
2394 NL80211_STA_BSS_PARAM_SHORT_SLOT_TIME,
2395 NL80211_STA_BSS_PARAM_DTIM_PERIOD,
2396 NL80211_STA_BSS_PARAM_BEACON_INTERVAL,
2399 __NL80211_STA_BSS_PARAM_AFTER_LAST,
2400 NL80211_STA_BSS_PARAM_MAX = __NL80211_STA_BSS_PARAM_AFTER_LAST - 1
2404 * enum nl80211_sta_info - station information
2406 * These attribute types are used with %NL80211_ATTR_STA_INFO
2407 * when getting information about a station.
2409 * @__NL80211_STA_INFO_INVALID: attribute number 0 is reserved
2410 * @NL80211_STA_INFO_INACTIVE_TIME: time since last activity (u32, msecs)
2411 * @NL80211_STA_INFO_RX_BYTES: total received bytes (MPDU length)
2412 * (u32, from this station)
2413 * @NL80211_STA_INFO_TX_BYTES: total transmitted bytes (MPDU length)
2414 * (u32, to this station)
2415 * @NL80211_STA_INFO_RX_BYTES64: total received bytes (MPDU length)
2416 * (u64, from this station)
2417 * @NL80211_STA_INFO_TX_BYTES64: total transmitted bytes (MPDU length)
2418 * (u64, to this station)
2419 * @NL80211_STA_INFO_SIGNAL: signal strength of last received PPDU (u8, dBm)
2420 * @NL80211_STA_INFO_TX_BITRATE: current unicast tx rate, nested attribute
2421 * containing info as possible, see &enum nl80211_rate_info
2422 * @NL80211_STA_INFO_RX_PACKETS: total received packet (MSDUs and MMPDUs)
2423 * (u32, from this station)
2424 * @NL80211_STA_INFO_TX_PACKETS: total transmitted packets (MSDUs and MMPDUs)
2425 * (u32, to this station)
2426 * @NL80211_STA_INFO_TX_RETRIES: total retries (MPDUs) (u32, to this station)
2427 * @NL80211_STA_INFO_TX_FAILED: total failed packets (MPDUs)
2428 * (u32, to this station)
2429 * @NL80211_STA_INFO_SIGNAL_AVG: signal strength average (u8, dBm)
2430 * @NL80211_STA_INFO_LLID: the station's mesh LLID
2431 * @NL80211_STA_INFO_PLID: the station's mesh PLID
2432 * @NL80211_STA_INFO_PLINK_STATE: peer link state for the station
2433 * (see %enum nl80211_plink_state)
2434 * @NL80211_STA_INFO_RX_BITRATE: last unicast data frame rx rate, nested
2435 * attribute, like NL80211_STA_INFO_TX_BITRATE.
2436 * @NL80211_STA_INFO_BSS_PARAM: current station's view of BSS, nested attribute
2437 * containing info as possible, see &enum nl80211_sta_bss_param
2438 * @NL80211_STA_INFO_CONNECTED_TIME: time since the station is last connected
2439 * @NL80211_STA_INFO_STA_FLAGS: Contains a struct nl80211_sta_flag_update.
2440 * @NL80211_STA_INFO_BEACON_LOSS: count of times beacon loss was detected (u32)
2441 * @NL80211_STA_INFO_T_OFFSET: timing offset with respect to this STA (s64)
2442 * @NL80211_STA_INFO_LOCAL_PM: local mesh STA link-specific power mode
2443 * @NL80211_STA_INFO_PEER_PM: peer mesh STA link-specific power mode
2444 * @NL80211_STA_INFO_NONPEER_PM: neighbor mesh STA power save mode towards
2446 * @NL80211_STA_INFO_CHAIN_SIGNAL: per-chain signal strength of last PPDU
2447 * Contains a nested array of signal strength attributes (u8, dBm)
2448 * @NL80211_STA_INFO_CHAIN_SIGNAL_AVG: per-chain signal strength average
2449 * Same format as NL80211_STA_INFO_CHAIN_SIGNAL.
2450 * @NL80211_STA_EXPECTED_THROUGHPUT: expected throughput considering also the
2451 * 802.11 header (u32, kbps)
2452 * @NL80211_STA_INFO_RX_DROP_MISC: RX packets dropped for unspecified reasons
2454 * @NL80211_STA_INFO_BEACON_RX: number of beacons received from this peer (u64)
2455 * @NL80211_STA_INFO_BEACON_SIGNAL_AVG: signal strength average
2456 * for beacons only (u8, dBm)
2457 * @NL80211_STA_INFO_TID_STATS: per-TID statistics (see &enum nl80211_tid_stats)
2458 * This is a nested attribute where each the inner attribute number is the
2459 * TID+1 and the special TID 16 (i.e. value 17) is used for non-QoS frames;
2460 * each one of those is again nested with &enum nl80211_tid_stats
2461 * attributes carrying the actual values.
2462 * @__NL80211_STA_INFO_AFTER_LAST: internal
2463 * @NL80211_STA_INFO_MAX: highest possible station info attribute
2465 enum nl80211_sta_info {
2466 __NL80211_STA_INFO_INVALID,
2467 NL80211_STA_INFO_INACTIVE_TIME,
2468 NL80211_STA_INFO_RX_BYTES,
2469 NL80211_STA_INFO_TX_BYTES,
2470 NL80211_STA_INFO_LLID,
2471 NL80211_STA_INFO_PLID,
2472 NL80211_STA_INFO_PLINK_STATE,
2473 NL80211_STA_INFO_SIGNAL,
2474 NL80211_STA_INFO_TX_BITRATE,
2475 NL80211_STA_INFO_RX_PACKETS,
2476 NL80211_STA_INFO_TX_PACKETS,
2477 NL80211_STA_INFO_TX_RETRIES,
2478 NL80211_STA_INFO_TX_FAILED,
2479 NL80211_STA_INFO_SIGNAL_AVG,
2480 NL80211_STA_INFO_RX_BITRATE,
2481 NL80211_STA_INFO_BSS_PARAM,
2482 NL80211_STA_INFO_CONNECTED_TIME,
2483 NL80211_STA_INFO_STA_FLAGS,
2484 NL80211_STA_INFO_BEACON_LOSS,
2485 NL80211_STA_INFO_T_OFFSET,
2486 NL80211_STA_INFO_LOCAL_PM,
2487 NL80211_STA_INFO_PEER_PM,
2488 NL80211_STA_INFO_NONPEER_PM,
2489 NL80211_STA_INFO_RX_BYTES64,
2490 NL80211_STA_INFO_TX_BYTES64,
2491 NL80211_STA_INFO_CHAIN_SIGNAL,
2492 NL80211_STA_INFO_CHAIN_SIGNAL_AVG,
2493 NL80211_STA_INFO_EXPECTED_THROUGHPUT,
2494 NL80211_STA_INFO_RX_DROP_MISC,
2495 NL80211_STA_INFO_BEACON_RX,
2496 NL80211_STA_INFO_BEACON_SIGNAL_AVG,
2497 NL80211_STA_INFO_TID_STATS,
2500 __NL80211_STA_INFO_AFTER_LAST,
2501 NL80211_STA_INFO_MAX = __NL80211_STA_INFO_AFTER_LAST - 1
2505 * enum nl80211_tid_stats - per TID statistics attributes
2506 * @__NL80211_TID_STATS_INVALID: attribute number 0 is reserved
2507 * @NL80211_TID_STATS_RX_MSDU: number of MSDUs received (u64)
2508 * @NL80211_TID_STATS_TX_MSDU: number of MSDUs transmitted (or
2509 * attempted to transmit; u64)
2510 * @NL80211_TID_STATS_TX_MSDU_RETRIES: number of retries for
2511 * transmitted MSDUs (not counting the first attempt; u64)
2512 * @NL80211_TID_STATS_TX_MSDU_FAILED: number of failed transmitted
2514 * @NUM_NL80211_TID_STATS: number of attributes here
2515 * @NL80211_TID_STATS_MAX: highest numbered attribute here
2517 enum nl80211_tid_stats {
2518 __NL80211_TID_STATS_INVALID,
2519 NL80211_TID_STATS_RX_MSDU,
2520 NL80211_TID_STATS_TX_MSDU,
2521 NL80211_TID_STATS_TX_MSDU_RETRIES,
2522 NL80211_TID_STATS_TX_MSDU_FAILED,
2525 NUM_NL80211_TID_STATS,
2526 NL80211_TID_STATS_MAX = NUM_NL80211_TID_STATS - 1
2530 * enum nl80211_mpath_flags - nl80211 mesh path flags
2532 * @NL80211_MPATH_FLAG_ACTIVE: the mesh path is active
2533 * @NL80211_MPATH_FLAG_RESOLVING: the mesh path discovery process is running
2534 * @NL80211_MPATH_FLAG_SN_VALID: the mesh path contains a valid SN
2535 * @NL80211_MPATH_FLAG_FIXED: the mesh path has been manually set
2536 * @NL80211_MPATH_FLAG_RESOLVED: the mesh path discovery process succeeded
2538 enum nl80211_mpath_flags {
2539 NL80211_MPATH_FLAG_ACTIVE = 1<<0,
2540 NL80211_MPATH_FLAG_RESOLVING = 1<<1,
2541 NL80211_MPATH_FLAG_SN_VALID = 1<<2,
2542 NL80211_MPATH_FLAG_FIXED = 1<<3,
2543 NL80211_MPATH_FLAG_RESOLVED = 1<<4,
2547 * enum nl80211_mpath_info - mesh path information
2549 * These attribute types are used with %NL80211_ATTR_MPATH_INFO when getting
2550 * information about a mesh path.
2552 * @__NL80211_MPATH_INFO_INVALID: attribute number 0 is reserved
2553 * @NL80211_MPATH_INFO_FRAME_QLEN: number of queued frames for this destination
2554 * @NL80211_MPATH_INFO_SN: destination sequence number
2555 * @NL80211_MPATH_INFO_METRIC: metric (cost) of this mesh path
2556 * @NL80211_MPATH_INFO_EXPTIME: expiration time for the path, in msec from now
2557 * @NL80211_MPATH_INFO_FLAGS: mesh path flags, enumerated in
2558 * &enum nl80211_mpath_flags;
2559 * @NL80211_MPATH_INFO_DISCOVERY_TIMEOUT: total path discovery timeout, in msec
2560 * @NL80211_MPATH_INFO_DISCOVERY_RETRIES: mesh path discovery retries
2561 * @NL80211_MPATH_INFO_MAX: highest mesh path information attribute number
2563 * @__NL80211_MPATH_INFO_AFTER_LAST: internal use
2565 enum nl80211_mpath_info {
2566 __NL80211_MPATH_INFO_INVALID,
2567 NL80211_MPATH_INFO_FRAME_QLEN,
2568 NL80211_MPATH_INFO_SN,
2569 NL80211_MPATH_INFO_METRIC,
2570 NL80211_MPATH_INFO_EXPTIME,
2571 NL80211_MPATH_INFO_FLAGS,
2572 NL80211_MPATH_INFO_DISCOVERY_TIMEOUT,
2573 NL80211_MPATH_INFO_DISCOVERY_RETRIES,
2576 __NL80211_MPATH_INFO_AFTER_LAST,
2577 NL80211_MPATH_INFO_MAX = __NL80211_MPATH_INFO_AFTER_LAST - 1
2581 * enum nl80211_band_attr - band attributes
2582 * @__NL80211_BAND_ATTR_INVALID: attribute number 0 is reserved
2583 * @NL80211_BAND_ATTR_FREQS: supported frequencies in this band,
2584 * an array of nested frequency attributes
2585 * @NL80211_BAND_ATTR_RATES: supported bitrates in this band,
2586 * an array of nested bitrate attributes
2587 * @NL80211_BAND_ATTR_HT_MCS_SET: 16-byte attribute containing the MCS set as
2588 * defined in 802.11n
2589 * @NL80211_BAND_ATTR_HT_CAPA: HT capabilities, as in the HT information IE
2590 * @NL80211_BAND_ATTR_HT_AMPDU_FACTOR: A-MPDU factor, as in 11n
2591 * @NL80211_BAND_ATTR_HT_AMPDU_DENSITY: A-MPDU density, as in 11n
2592 * @NL80211_BAND_ATTR_VHT_MCS_SET: 32-byte attribute containing the MCS set as
2593 * defined in 802.11ac
2594 * @NL80211_BAND_ATTR_VHT_CAPA: VHT capabilities, as in the HT information IE
2595 * @NL80211_BAND_ATTR_MAX: highest band attribute currently defined
2596 * @__NL80211_BAND_ATTR_AFTER_LAST: internal use
2598 enum nl80211_band_attr {
2599 __NL80211_BAND_ATTR_INVALID,
2600 NL80211_BAND_ATTR_FREQS,
2601 NL80211_BAND_ATTR_RATES,
2603 NL80211_BAND_ATTR_HT_MCS_SET,
2604 NL80211_BAND_ATTR_HT_CAPA,
2605 NL80211_BAND_ATTR_HT_AMPDU_FACTOR,
2606 NL80211_BAND_ATTR_HT_AMPDU_DENSITY,
2608 NL80211_BAND_ATTR_VHT_MCS_SET,
2609 NL80211_BAND_ATTR_VHT_CAPA,
2612 __NL80211_BAND_ATTR_AFTER_LAST,
2613 NL80211_BAND_ATTR_MAX = __NL80211_BAND_ATTR_AFTER_LAST - 1
2616 #define NL80211_BAND_ATTR_HT_CAPA NL80211_BAND_ATTR_HT_CAPA
2619 * enum nl80211_frequency_attr - frequency attributes
2620 * @__NL80211_FREQUENCY_ATTR_INVALID: attribute number 0 is reserved
2621 * @NL80211_FREQUENCY_ATTR_FREQ: Frequency in MHz
2622 * @NL80211_FREQUENCY_ATTR_DISABLED: Channel is disabled in current
2623 * regulatory domain.
2624 * @NL80211_FREQUENCY_ATTR_NO_IR: no mechanisms that initiate radiation
2625 * are permitted on this channel, this includes sending probe
2626 * requests, or modes of operation that require beaconing.
2627 * @NL80211_FREQUENCY_ATTR_RADAR: Radar detection is mandatory
2628 * on this channel in current regulatory domain.
2629 * @NL80211_FREQUENCY_ATTR_MAX_TX_POWER: Maximum transmission power in mBm
2631 * @NL80211_FREQUENCY_ATTR_DFS_STATE: current state for DFS
2632 * (enum nl80211_dfs_state)
2633 * @NL80211_FREQUENCY_ATTR_DFS_TIME: time in miliseconds for how long
2634 * this channel is in this DFS state.
2635 * @NL80211_FREQUENCY_ATTR_NO_HT40_MINUS: HT40- isn't possible with this
2636 * channel as the control channel
2637 * @NL80211_FREQUENCY_ATTR_NO_HT40_PLUS: HT40+ isn't possible with this
2638 * channel as the control channel
2639 * @NL80211_FREQUENCY_ATTR_NO_80MHZ: any 80 MHz channel using this channel
2640 * as the primary or any of the secondary channels isn't possible,
2641 * this includes 80+80 channels
2642 * @NL80211_FREQUENCY_ATTR_NO_160MHZ: any 160 MHz (but not 80+80) channel
2643 * using this channel as the primary or any of the secondary channels
2645 * @NL80211_FREQUENCY_ATTR_DFS_CAC_TIME: DFS CAC time in milliseconds.
2646 * @NL80211_FREQUENCY_ATTR_INDOOR_ONLY: Only indoor use is permitted on this
2647 * channel. A channel that has the INDOOR_ONLY attribute can only be
2648 * used when there is a clear assessment that the device is operating in
2649 * an indoor surroundings, i.e., it is connected to AC power (and not
2650 * through portable DC inverters) or is under the control of a master
2651 * that is acting as an AP and is connected to AC power.
2652 * @NL80211_FREQUENCY_ATTR_IR_CONCURRENT: IR operation is allowed on this
2653 * channel if it's connected concurrently to a BSS on the same channel on
2654 * the 2 GHz band or to a channel in the same UNII band (on the 5 GHz
2655 * band), and IEEE80211_CHAN_RADAR is not set. Instantiating a GO or TDLS
2656 * off-channel on a channel that has the IR_CONCURRENT attribute set can be
2657 * done when there is a clear assessment that the device is operating under
2658 * the guidance of an authorized master, i.e., setting up a GO or TDLS
2659 * off-channel while the device is also connected to an AP with DFS and
2660 * radar detection on the UNII band (it is up to user-space, i.e.,
2661 * wpa_supplicant to perform the required verifications). Using this
2662 * attribute for IR is disallowed for master interfaces (IBSS, AP).
2663 * @NL80211_FREQUENCY_ATTR_NO_20MHZ: 20 MHz operation is not allowed
2664 * on this channel in current regulatory domain.
2665 * @NL80211_FREQUENCY_ATTR_NO_10MHZ: 10 MHz operation is not allowed
2666 * on this channel in current regulatory domain.
2667 * @NL80211_FREQUENCY_ATTR_MAX: highest frequency attribute number
2669 * @__NL80211_FREQUENCY_ATTR_AFTER_LAST: internal use
2671 * See https://apps.fcc.gov/eas/comments/GetPublishedDocument.html?id=327&tn=528122
2672 * for more information on the FCC description of the relaxations allowed
2673 * by NL80211_FREQUENCY_ATTR_INDOOR_ONLY and
2674 * NL80211_FREQUENCY_ATTR_IR_CONCURRENT.
2676 enum nl80211_frequency_attr {
2677 __NL80211_FREQUENCY_ATTR_INVALID,
2678 NL80211_FREQUENCY_ATTR_FREQ,
2679 NL80211_FREQUENCY_ATTR_DISABLED,
2680 NL80211_FREQUENCY_ATTR_NO_IR,
2681 __NL80211_FREQUENCY_ATTR_NO_IBSS,
2682 NL80211_FREQUENCY_ATTR_RADAR,
2683 NL80211_FREQUENCY_ATTR_MAX_TX_POWER,
2684 NL80211_FREQUENCY_ATTR_DFS_STATE,
2685 NL80211_FREQUENCY_ATTR_DFS_TIME,
2686 NL80211_FREQUENCY_ATTR_NO_HT40_MINUS,
2687 NL80211_FREQUENCY_ATTR_NO_HT40_PLUS,
2688 NL80211_FREQUENCY_ATTR_NO_80MHZ,
2689 NL80211_FREQUENCY_ATTR_NO_160MHZ,
2690 NL80211_FREQUENCY_ATTR_DFS_CAC_TIME,
2691 NL80211_FREQUENCY_ATTR_INDOOR_ONLY,
2692 NL80211_FREQUENCY_ATTR_IR_CONCURRENT,
2693 NL80211_FREQUENCY_ATTR_NO_20MHZ,
2694 NL80211_FREQUENCY_ATTR_NO_10MHZ,
2697 __NL80211_FREQUENCY_ATTR_AFTER_LAST,
2698 NL80211_FREQUENCY_ATTR_MAX = __NL80211_FREQUENCY_ATTR_AFTER_LAST - 1
2701 #define NL80211_FREQUENCY_ATTR_MAX_TX_POWER NL80211_FREQUENCY_ATTR_MAX_TX_POWER
2702 #define NL80211_FREQUENCY_ATTR_PASSIVE_SCAN NL80211_FREQUENCY_ATTR_NO_IR
2703 #define NL80211_FREQUENCY_ATTR_NO_IBSS NL80211_FREQUENCY_ATTR_NO_IR
2704 #define NL80211_FREQUENCY_ATTR_NO_IR NL80211_FREQUENCY_ATTR_NO_IR
2705 #define NL80211_FREQUENCY_ATTR_GO_CONCURRENT \
2706 NL80211_FREQUENCY_ATTR_IR_CONCURRENT
2709 * enum nl80211_bitrate_attr - bitrate attributes
2710 * @__NL80211_BITRATE_ATTR_INVALID: attribute number 0 is reserved
2711 * @NL80211_BITRATE_ATTR_RATE: Bitrate in units of 100 kbps
2712 * @NL80211_BITRATE_ATTR_2GHZ_SHORTPREAMBLE: Short preamble supported
2714 * @NL80211_BITRATE_ATTR_MAX: highest bitrate attribute number
2716 * @__NL80211_BITRATE_ATTR_AFTER_LAST: internal use
2718 enum nl80211_bitrate_attr {
2719 __NL80211_BITRATE_ATTR_INVALID,
2720 NL80211_BITRATE_ATTR_RATE,
2721 NL80211_BITRATE_ATTR_2GHZ_SHORTPREAMBLE,
2724 __NL80211_BITRATE_ATTR_AFTER_LAST,
2725 NL80211_BITRATE_ATTR_MAX = __NL80211_BITRATE_ATTR_AFTER_LAST - 1
2729 * enum nl80211_initiator - Indicates the initiator of a reg domain request
2730 * @NL80211_REGDOM_SET_BY_CORE: Core queried CRDA for a dynamic world
2731 * regulatory domain.
2732 * @NL80211_REGDOM_SET_BY_USER: User asked the wireless core to set the
2733 * regulatory domain.
2734 * @NL80211_REGDOM_SET_BY_DRIVER: a wireless drivers has hinted to the
2735 * wireless core it thinks its knows the regulatory domain we should be in.
2736 * @NL80211_REGDOM_SET_BY_COUNTRY_IE: the wireless core has received an
2737 * 802.11 country information element with regulatory information it
2738 * thinks we should consider. cfg80211 only processes the country
2739 * code from the IE, and relies on the regulatory domain information
2740 * structure passed by userspace (CRDA) from our wireless-regdb.
2741 * If a channel is enabled but the country code indicates it should
2742 * be disabled we disable the channel and re-enable it upon disassociation.
2744 enum nl80211_reg_initiator {
2745 NL80211_REGDOM_SET_BY_CORE,
2746 NL80211_REGDOM_SET_BY_USER,
2747 NL80211_REGDOM_SET_BY_DRIVER,
2748 NL80211_REGDOM_SET_BY_COUNTRY_IE,
2752 * enum nl80211_reg_type - specifies the type of regulatory domain
2753 * @NL80211_REGDOM_TYPE_COUNTRY: the regulatory domain set is one that pertains
2754 * to a specific country. When this is set you can count on the
2755 * ISO / IEC 3166 alpha2 country code being valid.
2756 * @NL80211_REGDOM_TYPE_WORLD: the regulatory set domain is the world regulatory
2758 * @NL80211_REGDOM_TYPE_CUSTOM_WORLD: the regulatory domain set is a custom
2759 * driver specific world regulatory domain. These do not apply system-wide
2760 * and are only applicable to the individual devices which have requested
2761 * them to be applied.
2762 * @NL80211_REGDOM_TYPE_INTERSECTION: the regulatory domain set is the product
2763 * of an intersection between two regulatory domains -- the previously
2764 * set regulatory domain on the system and the last accepted regulatory
2765 * domain request to be processed.
2767 enum nl80211_reg_type {
2768 NL80211_REGDOM_TYPE_COUNTRY,
2769 NL80211_REGDOM_TYPE_WORLD,
2770 NL80211_REGDOM_TYPE_CUSTOM_WORLD,
2771 NL80211_REGDOM_TYPE_INTERSECTION,
2775 * enum nl80211_reg_rule_attr - regulatory rule attributes
2776 * @__NL80211_REG_RULE_ATTR_INVALID: attribute number 0 is reserved
2777 * @NL80211_ATTR_REG_RULE_FLAGS: a set of flags which specify additional
2778 * considerations for a given frequency range. These are the
2779 * &enum nl80211_reg_rule_flags.
2780 * @NL80211_ATTR_FREQ_RANGE_START: starting frequencry for the regulatory
2781 * rule in KHz. This is not a center of frequency but an actual regulatory
2783 * @NL80211_ATTR_FREQ_RANGE_END: ending frequency for the regulatory rule
2784 * in KHz. This is not a center a frequency but an actual regulatory
2786 * @NL80211_ATTR_FREQ_RANGE_MAX_BW: maximum allowed bandwidth for this
2787 * frequency range, in KHz.
2788 * @NL80211_ATTR_POWER_RULE_MAX_ANT_GAIN: the maximum allowed antenna gain
2789 * for a given frequency range. The value is in mBi (100 * dBi).
2790 * If you don't have one then don't send this.
2791 * @NL80211_ATTR_POWER_RULE_MAX_EIRP: the maximum allowed EIRP for
2792 * a given frequency range. The value is in mBm (100 * dBm).
2793 * @NL80211_ATTR_DFS_CAC_TIME: DFS CAC time in milliseconds.
2794 * If not present or 0 default CAC time will be used.
2795 * @NL80211_REG_RULE_ATTR_MAX: highest regulatory rule attribute number
2797 * @__NL80211_REG_RULE_ATTR_AFTER_LAST: internal use
2799 enum nl80211_reg_rule_attr {
2800 __NL80211_REG_RULE_ATTR_INVALID,
2801 NL80211_ATTR_REG_RULE_FLAGS,
2803 NL80211_ATTR_FREQ_RANGE_START,
2804 NL80211_ATTR_FREQ_RANGE_END,
2805 NL80211_ATTR_FREQ_RANGE_MAX_BW,
2807 NL80211_ATTR_POWER_RULE_MAX_ANT_GAIN,
2808 NL80211_ATTR_POWER_RULE_MAX_EIRP,
2810 NL80211_ATTR_DFS_CAC_TIME,
2813 __NL80211_REG_RULE_ATTR_AFTER_LAST,
2814 NL80211_REG_RULE_ATTR_MAX = __NL80211_REG_RULE_ATTR_AFTER_LAST - 1
2818 * enum nl80211_sched_scan_match_attr - scheduled scan match attributes
2819 * @__NL80211_SCHED_SCAN_MATCH_ATTR_INVALID: attribute number 0 is reserved
2820 * @NL80211_SCHED_SCAN_MATCH_ATTR_SSID: SSID to be used for matching,
2821 * only report BSS with matching SSID.
2822 * @NL80211_SCHED_SCAN_MATCH_ATTR_RSSI: RSSI threshold (in dBm) for reporting a
2823 * BSS in scan results. Filtering is turned off if not specified. Note that
2824 * if this attribute is in a match set of its own, then it is treated as
2825 * the default value for all matchsets with an SSID, rather than being a
2826 * matchset of its own without an RSSI filter. This is due to problems with
2827 * how this API was implemented in the past. Also, due to the same problem,
2828 * the only way to create a matchset with only an RSSI filter (with this
2829 * attribute) is if there's only a single matchset with the RSSI attribute.
2830 * @NL80211_SCHED_SCAN_MATCH_ATTR_MAX: highest scheduled scan filter
2831 * attribute number currently defined
2832 * @__NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST: internal use
2834 enum nl80211_sched_scan_match_attr {
2835 __NL80211_SCHED_SCAN_MATCH_ATTR_INVALID,
2837 NL80211_SCHED_SCAN_MATCH_ATTR_SSID,
2838 NL80211_SCHED_SCAN_MATCH_ATTR_RSSI,
2841 __NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST,
2842 NL80211_SCHED_SCAN_MATCH_ATTR_MAX =
2843 __NL80211_SCHED_SCAN_MATCH_ATTR_AFTER_LAST - 1
2846 /* only for backward compatibility */
2847 #define NL80211_ATTR_SCHED_SCAN_MATCH_SSID NL80211_SCHED_SCAN_MATCH_ATTR_SSID
2850 * enum nl80211_reg_rule_flags - regulatory rule flags
2852 * @NL80211_RRF_NO_OFDM: OFDM modulation not allowed
2853 * @NL80211_RRF_NO_CCK: CCK modulation not allowed
2854 * @NL80211_RRF_NO_INDOOR: indoor operation not allowed
2855 * @NL80211_RRF_NO_OUTDOOR: outdoor operation not allowed
2856 * @NL80211_RRF_DFS: DFS support is required to be used
2857 * @NL80211_RRF_PTP_ONLY: this is only for Point To Point links
2858 * @NL80211_RRF_PTMP_ONLY: this is only for Point To Multi Point links
2859 * @NL80211_RRF_NO_IR: no mechanisms that initiate radiation are allowed,
2860 * this includes probe requests or modes of operation that require
2862 * @NL80211_RRF_AUTO_BW: maximum available bandwidth should be calculated
2863 * base on contiguous rules and wider channels will be allowed to cross
2864 * multiple contiguous/overlapping frequency ranges.
2865 * @NL80211_RRF_IR_CONCURRENT: See &NL80211_FREQUENCY_ATTR_IR_CONCURRENT
2866 * @NL80211_RRF_NO_HT40MINUS: channels can't be used in HT40- operation
2867 * @NL80211_RRF_NO_HT40PLUS: channels can't be used in HT40+ operation
2868 * @NL80211_RRF_NO_80MHZ: 80MHz operation not allowed
2869 * @NL80211_RRF_NO_160MHZ: 160MHz operation not allowed
2871 enum nl80211_reg_rule_flags {
2872 NL80211_RRF_NO_OFDM = 1<<0,
2873 NL80211_RRF_NO_CCK = 1<<1,
2874 NL80211_RRF_NO_INDOOR = 1<<2,
2875 NL80211_RRF_NO_OUTDOOR = 1<<3,
2876 NL80211_RRF_DFS = 1<<4,
2877 NL80211_RRF_PTP_ONLY = 1<<5,
2878 NL80211_RRF_PTMP_ONLY = 1<<6,
2879 NL80211_RRF_NO_IR = 1<<7,
2880 __NL80211_RRF_NO_IBSS = 1<<8,
2881 NL80211_RRF_AUTO_BW = 1<<11,
2882 NL80211_RRF_IR_CONCURRENT = 1<<12,
2883 NL80211_RRF_NO_HT40MINUS = 1<<13,
2884 NL80211_RRF_NO_HT40PLUS = 1<<14,
2885 NL80211_RRF_NO_80MHZ = 1<<15,
2886 NL80211_RRF_NO_160MHZ = 1<<16,
2889 #define NL80211_RRF_PASSIVE_SCAN NL80211_RRF_NO_IR
2890 #define NL80211_RRF_NO_IBSS NL80211_RRF_NO_IR
2891 #define NL80211_RRF_NO_IR NL80211_RRF_NO_IR
2892 #define NL80211_RRF_NO_HT40 (NL80211_RRF_NO_HT40MINUS |\
2893 NL80211_RRF_NO_HT40PLUS)
2894 #define NL80211_RRF_GO_CONCURRENT NL80211_RRF_IR_CONCURRENT
2896 /* For backport compatibility with older userspace */
2897 #define NL80211_RRF_NO_IR_ALL (NL80211_RRF_NO_IR | __NL80211_RRF_NO_IBSS)
2900 * enum nl80211_dfs_regions - regulatory DFS regions
2902 * @NL80211_DFS_UNSET: Country has no DFS master region specified
2903 * @NL80211_DFS_FCC: Country follows DFS master rules from FCC
2904 * @NL80211_DFS_ETSI: Country follows DFS master rules from ETSI
2905 * @NL80211_DFS_JP: Country follows DFS master rules from JP/MKK/Telec
2907 enum nl80211_dfs_regions {
2908 NL80211_DFS_UNSET = 0,
2909 NL80211_DFS_FCC = 1,
2910 NL80211_DFS_ETSI = 2,
2915 * enum nl80211_user_reg_hint_type - type of user regulatory hint
2917 * @NL80211_USER_REG_HINT_USER: a user sent the hint. This is always
2918 * assumed if the attribute is not set.
2919 * @NL80211_USER_REG_HINT_CELL_BASE: the hint comes from a cellular
2920 * base station. Device drivers that have been tested to work
2921 * properly to support this type of hint can enable these hints
2922 * by setting the NL80211_FEATURE_CELL_BASE_REG_HINTS feature
2923 * capability on the struct wiphy. The wireless core will
2924 * ignore all cell base station hints until at least one device
2925 * present has been registered with the wireless core that
2926 * has listed NL80211_FEATURE_CELL_BASE_REG_HINTS as a
2927 * supported feature.
2928 * @NL80211_USER_REG_HINT_INDOOR: a user sent an hint indicating that the
2929 * platform is operating in an indoor environment.
2931 enum nl80211_user_reg_hint_type {
2932 NL80211_USER_REG_HINT_USER = 0,
2933 NL80211_USER_REG_HINT_CELL_BASE = 1,
2934 NL80211_USER_REG_HINT_INDOOR = 2,
2938 * enum nl80211_survey_info - survey information
2940 * These attribute types are used with %NL80211_ATTR_SURVEY_INFO
2941 * when getting information about a survey.
2943 * @__NL80211_SURVEY_INFO_INVALID: attribute number 0 is reserved
2944 * @NL80211_SURVEY_INFO_FREQUENCY: center frequency of channel
2945 * @NL80211_SURVEY_INFO_NOISE: noise level of channel (u8, dBm)
2946 * @NL80211_SURVEY_INFO_IN_USE: channel is currently being used
2947 * @NL80211_SURVEY_INFO_TIME: amount of time (in ms) that the radio
2948 * was turned on (on channel or globally)
2949 * @NL80211_SURVEY_INFO_TIME_BUSY: amount of the time the primary
2950 * channel was sensed busy (either due to activity or energy detect)
2951 * @NL80211_SURVEY_INFO_TIME_EXT_BUSY: amount of time the extension
2952 * channel was sensed busy
2953 * @NL80211_SURVEY_INFO_TIME_RX: amount of time the radio spent
2954 * receiving data (on channel or globally)
2955 * @NL80211_SURVEY_INFO_TIME_TX: amount of time the radio spent
2956 * transmitting data (on channel or globally)
2957 * @NL80211_SURVEY_INFO_TIME_SCAN: time the radio spent for scan
2958 * (on this channel or globally)
2959 * @NL80211_SURVEY_INFO_MAX: highest survey info attribute number
2961 * @__NL80211_SURVEY_INFO_AFTER_LAST: internal use
2963 enum nl80211_survey_info {
2964 __NL80211_SURVEY_INFO_INVALID,
2965 NL80211_SURVEY_INFO_FREQUENCY,
2966 NL80211_SURVEY_INFO_NOISE,
2967 NL80211_SURVEY_INFO_IN_USE,
2968 NL80211_SURVEY_INFO_TIME,
2969 NL80211_SURVEY_INFO_TIME_BUSY,
2970 NL80211_SURVEY_INFO_TIME_EXT_BUSY,
2971 NL80211_SURVEY_INFO_TIME_RX,
2972 NL80211_SURVEY_INFO_TIME_TX,
2973 NL80211_SURVEY_INFO_TIME_SCAN,
2976 __NL80211_SURVEY_INFO_AFTER_LAST,
2977 NL80211_SURVEY_INFO_MAX = __NL80211_SURVEY_INFO_AFTER_LAST - 1
2980 /* keep old names for compatibility */
2981 #define NL80211_SURVEY_INFO_CHANNEL_TIME NL80211_SURVEY_INFO_TIME
2982 #define NL80211_SURVEY_INFO_CHANNEL_TIME_BUSY NL80211_SURVEY_INFO_TIME_BUSY
2983 #define NL80211_SURVEY_INFO_CHANNEL_TIME_EXT_BUSY NL80211_SURVEY_INFO_TIME_EXT_BUSY
2984 #define NL80211_SURVEY_INFO_CHANNEL_TIME_RX NL80211_SURVEY_INFO_TIME_RX
2985 #define NL80211_SURVEY_INFO_CHANNEL_TIME_TX NL80211_SURVEY_INFO_TIME_TX
2988 * enum nl80211_mntr_flags - monitor configuration flags
2990 * Monitor configuration flags.
2992 * @__NL80211_MNTR_FLAG_INVALID: reserved
2994 * @NL80211_MNTR_FLAG_FCSFAIL: pass frames with bad FCS
2995 * @NL80211_MNTR_FLAG_PLCPFAIL: pass frames with bad PLCP
2996 * @NL80211_MNTR_FLAG_CONTROL: pass control frames
2997 * @NL80211_MNTR_FLAG_OTHER_BSS: disable BSSID filtering
2998 * @NL80211_MNTR_FLAG_COOK_FRAMES: report frames after processing.
2999 * overrides all other flags.
3000 * @NL80211_MNTR_FLAG_ACTIVE: use the configured MAC address
3001 * and ACK incoming unicast packets.
3003 * @__NL80211_MNTR_FLAG_AFTER_LAST: internal use
3004 * @NL80211_MNTR_FLAG_MAX: highest possible monitor flag
3006 enum nl80211_mntr_flags {
3007 __NL80211_MNTR_FLAG_INVALID,
3008 NL80211_MNTR_FLAG_FCSFAIL,
3009 NL80211_MNTR_FLAG_PLCPFAIL,
3010 NL80211_MNTR_FLAG_CONTROL,
3011 NL80211_MNTR_FLAG_OTHER_BSS,
3012 NL80211_MNTR_FLAG_COOK_FRAMES,
3013 NL80211_MNTR_FLAG_ACTIVE,
3016 __NL80211_MNTR_FLAG_AFTER_LAST,
3017 NL80211_MNTR_FLAG_MAX = __NL80211_MNTR_FLAG_AFTER_LAST - 1
3021 * enum nl80211_mesh_power_mode - mesh power save modes
3023 * @NL80211_MESH_POWER_UNKNOWN: The mesh power mode of the mesh STA is
3024 * not known or has not been set yet.
3025 * @NL80211_MESH_POWER_ACTIVE: Active mesh power mode. The mesh STA is
3026 * in Awake state all the time.
3027 * @NL80211_MESH_POWER_LIGHT_SLEEP: Light sleep mode. The mesh STA will
3028 * alternate between Active and Doze states, but will wake up for
3029 * neighbor's beacons.
3030 * @NL80211_MESH_POWER_DEEP_SLEEP: Deep sleep mode. The mesh STA will
3031 * alternate between Active and Doze states, but may not wake up
3032 * for neighbor's beacons.
3034 * @__NL80211_MESH_POWER_AFTER_LAST - internal use
3035 * @NL80211_MESH_POWER_MAX - highest possible power save level
3038 enum nl80211_mesh_power_mode {
3039 NL80211_MESH_POWER_UNKNOWN,
3040 NL80211_MESH_POWER_ACTIVE,
3041 NL80211_MESH_POWER_LIGHT_SLEEP,
3042 NL80211_MESH_POWER_DEEP_SLEEP,
3044 __NL80211_MESH_POWER_AFTER_LAST,
3045 NL80211_MESH_POWER_MAX = __NL80211_MESH_POWER_AFTER_LAST - 1
3049 * enum nl80211_meshconf_params - mesh configuration parameters
3051 * Mesh configuration parameters. These can be changed while the mesh is
3054 * @__NL80211_MESHCONF_INVALID: internal use
3056 * @NL80211_MESHCONF_RETRY_TIMEOUT: specifies the initial retry timeout in
3057 * millisecond units, used by the Peer Link Open message
3059 * @NL80211_MESHCONF_CONFIRM_TIMEOUT: specifies the initial confirm timeout, in
3060 * millisecond units, used by the peer link management to close a peer link
3062 * @NL80211_MESHCONF_HOLDING_TIMEOUT: specifies the holding timeout, in
3065 * @NL80211_MESHCONF_MAX_PEER_LINKS: maximum number of peer links allowed
3066 * on this mesh interface
3068 * @NL80211_MESHCONF_MAX_RETRIES: specifies the maximum number of peer link
3069 * open retries that can be sent to establish a new peer link instance in a
3072 * @NL80211_MESHCONF_TTL: specifies the value of TTL field set at a source mesh
3075 * @NL80211_MESHCONF_AUTO_OPEN_PLINKS: whether we should automatically open
3076 * peer links when we detect compatible mesh peers. Disabled if
3077 * @NL80211_MESH_SETUP_USERSPACE_MPM or @NL80211_MESH_SETUP_USERSPACE_AMPE are
3080 * @NL80211_MESHCONF_HWMP_MAX_PREQ_RETRIES: the number of action frames
3081 * containing a PREQ that an MP can send to a particular destination (path
3084 * @NL80211_MESHCONF_PATH_REFRESH_TIME: how frequently to refresh mesh paths
3087 * @NL80211_MESHCONF_MIN_DISCOVERY_TIMEOUT: minimum length of time to wait
3088 * until giving up on a path discovery (in milliseconds)
3090 * @NL80211_MESHCONF_HWMP_ACTIVE_PATH_TIMEOUT: The time (in TUs) for which mesh
3091 * points receiving a PREQ shall consider the forwarding information from
3092 * the root to be valid. (TU = time unit)
3094 * @NL80211_MESHCONF_HWMP_PREQ_MIN_INTERVAL: The minimum interval of time (in
3095 * TUs) during which an MP can send only one action frame containing a PREQ
3098 * @NL80211_MESHCONF_HWMP_NET_DIAM_TRVS_TIME: The interval of time (in TUs)
3099 * that it takes for an HWMP information element to propagate across the
3102 * @NL80211_MESHCONF_HWMP_ROOTMODE: whether root mode is enabled or not
3104 * @NL80211_MESHCONF_ELEMENT_TTL: specifies the value of TTL field set at a
3105 * source mesh point for path selection elements.
3107 * @NL80211_MESHCONF_HWMP_RANN_INTERVAL: The interval of time (in TUs) between
3108 * root announcements are transmitted.
3110 * @NL80211_MESHCONF_GATE_ANNOUNCEMENTS: Advertise that this mesh station has
3111 * access to a broader network beyond the MBSS. This is done via Root
3112 * Announcement frames.
3114 * @NL80211_MESHCONF_HWMP_PERR_MIN_INTERVAL: The minimum interval of time (in
3115 * TUs) during which a mesh STA can send only one Action frame containing a
3118 * @NL80211_MESHCONF_FORWARDING: set Mesh STA as forwarding or non-forwarding
3119 * or forwarding entity (default is TRUE - forwarding entity)
3121 * @NL80211_MESHCONF_RSSI_THRESHOLD: RSSI threshold in dBm. This specifies the
3122 * threshold for average signal strength of candidate station to establish
3125 * @NL80211_MESHCONF_SYNC_OFFSET_MAX_NEIGHBOR: maximum number of neighbors
3126 * to synchronize to for 11s default synchronization method
3129 * @NL80211_MESHCONF_HT_OPMODE: set mesh HT protection mode.
3131 * @NL80211_MESHCONF_ATTR_MAX: highest possible mesh configuration attribute
3133 * @NL80211_MESHCONF_HWMP_PATH_TO_ROOT_TIMEOUT: The time (in TUs) for
3134 * which mesh STAs receiving a proactive PREQ shall consider the forwarding
3135 * information to the root mesh STA to be valid.
3137 * @NL80211_MESHCONF_HWMP_ROOT_INTERVAL: The interval of time (in TUs) between
3138 * proactive PREQs are transmitted.
3140 * @NL80211_MESHCONF_HWMP_CONFIRMATION_INTERVAL: The minimum interval of time
3141 * (in TUs) during which a mesh STA can send only one Action frame
3142 * containing a PREQ element for root path confirmation.
3144 * @NL80211_MESHCONF_POWER_MODE: Default mesh power mode for new peer links.
3145 * type &enum nl80211_mesh_power_mode (u32)
3147 * @NL80211_MESHCONF_AWAKE_WINDOW: awake window duration (in TUs)
3149 * @NL80211_MESHCONF_PLINK_TIMEOUT: If no tx activity is seen from a STA we've
3150 * established peering with for longer than this time (in seconds), then
3151 * remove it from the STA's list of peers. You may set this to 0 to disable
3152 * the removal of the STA. Default is 30 minutes.
3154 * @__NL80211_MESHCONF_ATTR_AFTER_LAST: internal use
3156 enum nl80211_meshconf_params {
3157 __NL80211_MESHCONF_INVALID,
3158 NL80211_MESHCONF_RETRY_TIMEOUT,
3159 NL80211_MESHCONF_CONFIRM_TIMEOUT,
3160 NL80211_MESHCONF_HOLDING_TIMEOUT,
3161 NL80211_MESHCONF_MAX_PEER_LINKS,
3162 NL80211_MESHCONF_MAX_RETRIES,
3163 NL80211_MESHCONF_TTL,
3164 NL80211_MESHCONF_AUTO_OPEN_PLINKS,
3165 NL80211_MESHCONF_HWMP_MAX_PREQ_RETRIES,
3166 NL80211_MESHCONF_PATH_REFRESH_TIME,
3167 NL80211_MESHCONF_MIN_DISCOVERY_TIMEOUT,
3168 NL80211_MESHCONF_HWMP_ACTIVE_PATH_TIMEOUT,
3169 NL80211_MESHCONF_HWMP_PREQ_MIN_INTERVAL,
3170 NL80211_MESHCONF_HWMP_NET_DIAM_TRVS_TIME,
3171 NL80211_MESHCONF_HWMP_ROOTMODE,
3172 NL80211_MESHCONF_ELEMENT_TTL,
3173 NL80211_MESHCONF_HWMP_RANN_INTERVAL,
3174 NL80211_MESHCONF_GATE_ANNOUNCEMENTS,
3175 NL80211_MESHCONF_HWMP_PERR_MIN_INTERVAL,
3176 NL80211_MESHCONF_FORWARDING,
3177 NL80211_MESHCONF_RSSI_THRESHOLD,
3178 NL80211_MESHCONF_SYNC_OFFSET_MAX_NEIGHBOR,
3179 NL80211_MESHCONF_HT_OPMODE,
3180 NL80211_MESHCONF_HWMP_PATH_TO_ROOT_TIMEOUT,
3181 NL80211_MESHCONF_HWMP_ROOT_INTERVAL,
3182 NL80211_MESHCONF_HWMP_CONFIRMATION_INTERVAL,
3183 NL80211_MESHCONF_POWER_MODE,
3184 NL80211_MESHCONF_AWAKE_WINDOW,
3185 NL80211_MESHCONF_PLINK_TIMEOUT,
3188 __NL80211_MESHCONF_ATTR_AFTER_LAST,
3189 NL80211_MESHCONF_ATTR_MAX = __NL80211_MESHCONF_ATTR_AFTER_LAST - 1
3193 * enum nl80211_mesh_setup_params - mesh setup parameters
3195 * Mesh setup parameters. These are used to start/join a mesh and cannot be
3196 * changed while the mesh is active.
3198 * @__NL80211_MESH_SETUP_INVALID: Internal use
3200 * @NL80211_MESH_SETUP_ENABLE_VENDOR_PATH_SEL: Enable this option to use a
3201 * vendor specific path selection algorithm or disable it to use the
3204 * @NL80211_MESH_SETUP_ENABLE_VENDOR_METRIC: Enable this option to use a
3205 * vendor specific path metric or disable it to use the default Airtime
3208 * @NL80211_MESH_SETUP_IE: Information elements for this mesh, for instance, a
3209 * robust security network ie, or a vendor specific information element
3210 * that vendors will use to identify the path selection methods and
3213 * @NL80211_MESH_SETUP_USERSPACE_AUTH: Enable this option if an authentication
3214 * daemon will be authenticating mesh candidates.
3216 * @NL80211_MESH_SETUP_USERSPACE_AMPE: Enable this option if an authentication
3217 * daemon will be securing peer link frames. AMPE is a secured version of
3218 * Mesh Peering Management (MPM) and is implemented with the assistance of
3219 * a userspace daemon. When this flag is set, the kernel will send peer
3220 * management frames to a userspace daemon that will implement AMPE
3221 * functionality (security capabilities selection, key confirmation, and
3222 * key management). When the flag is unset (default), the kernel can
3223 * autonomously complete (unsecured) mesh peering without the need of a
3226 * @NL80211_MESH_SETUP_ENABLE_VENDOR_SYNC: Enable this option to use a
3227 * vendor specific synchronization method or disable it to use the default
3228 * neighbor offset synchronization
3230 * @NL80211_MESH_SETUP_USERSPACE_MPM: Enable this option if userspace will
3231 * implement an MPM which handles peer allocation and state.
3233 * @NL80211_MESH_SETUP_AUTH_PROTOCOL: Inform the kernel of the authentication
3234 * method (u8, as defined in IEEE 8.4.2.100.6, e.g. 0x1 for SAE).
3235 * Default is no authentication method required.
3237 * @NL80211_MESH_SETUP_ATTR_MAX: highest possible mesh setup attribute number
3239 * @__NL80211_MESH_SETUP_ATTR_AFTER_LAST: Internal use
3241 enum nl80211_mesh_setup_params {
3242 __NL80211_MESH_SETUP_INVALID,
3243 NL80211_MESH_SETUP_ENABLE_VENDOR_PATH_SEL,
3244 NL80211_MESH_SETUP_ENABLE_VENDOR_METRIC,
3245 NL80211_MESH_SETUP_IE,
3246 NL80211_MESH_SETUP_USERSPACE_AUTH,
3247 NL80211_MESH_SETUP_USERSPACE_AMPE,
3248 NL80211_MESH_SETUP_ENABLE_VENDOR_SYNC,
3249 NL80211_MESH_SETUP_USERSPACE_MPM,
3250 NL80211_MESH_SETUP_AUTH_PROTOCOL,
3253 __NL80211_MESH_SETUP_ATTR_AFTER_LAST,
3254 NL80211_MESH_SETUP_ATTR_MAX = __NL80211_MESH_SETUP_ATTR_AFTER_LAST - 1
3258 * enum nl80211_txq_attr - TX queue parameter attributes
3259 * @__NL80211_TXQ_ATTR_INVALID: Attribute number 0 is reserved
3260 * @NL80211_TXQ_ATTR_AC: AC identifier (NL80211_AC_*)
3261 * @NL80211_TXQ_ATTR_TXOP: Maximum burst time in units of 32 usecs, 0 meaning
3263 * @NL80211_TXQ_ATTR_CWMIN: Minimum contention window [a value of the form
3264 * 2^n-1 in the range 1..32767]
3265 * @NL80211_TXQ_ATTR_CWMAX: Maximum contention window [a value of the form
3266 * 2^n-1 in the range 1..32767]
3267 * @NL80211_TXQ_ATTR_AIFS: Arbitration interframe space [0..255]
3268 * @__NL80211_TXQ_ATTR_AFTER_LAST: Internal
3269 * @NL80211_TXQ_ATTR_MAX: Maximum TXQ attribute number
3271 enum nl80211_txq_attr {
3272 __NL80211_TXQ_ATTR_INVALID,
3273 NL80211_TXQ_ATTR_AC,
3274 NL80211_TXQ_ATTR_TXOP,
3275 NL80211_TXQ_ATTR_CWMIN,
3276 NL80211_TXQ_ATTR_CWMAX,
3277 NL80211_TXQ_ATTR_AIFS,
3280 __NL80211_TXQ_ATTR_AFTER_LAST,
3281 NL80211_TXQ_ATTR_MAX = __NL80211_TXQ_ATTR_AFTER_LAST - 1
3292 /* backward compat */
3293 #define NL80211_TXQ_ATTR_QUEUE NL80211_TXQ_ATTR_AC
3294 #define NL80211_TXQ_Q_VO NL80211_AC_VO
3295 #define NL80211_TXQ_Q_VI NL80211_AC_VI
3296 #define NL80211_TXQ_Q_BE NL80211_AC_BE
3297 #define NL80211_TXQ_Q_BK NL80211_AC_BK
3300 * enum nl80211_channel_type - channel type
3301 * @NL80211_CHAN_NO_HT: 20 MHz, non-HT channel
3302 * @NL80211_CHAN_HT20: 20 MHz HT channel
3303 * @NL80211_CHAN_HT40MINUS: HT40 channel, secondary channel
3304 * below the control channel
3305 * @NL80211_CHAN_HT40PLUS: HT40 channel, secondary channel
3306 * above the control channel
3308 enum nl80211_channel_type {
3311 NL80211_CHAN_HT40MINUS,
3312 NL80211_CHAN_HT40PLUS
3316 * enum nl80211_chan_width - channel width definitions
3318 * These values are used with the %NL80211_ATTR_CHANNEL_WIDTH
3321 * @NL80211_CHAN_WIDTH_20_NOHT: 20 MHz, non-HT channel
3322 * @NL80211_CHAN_WIDTH_20: 20 MHz HT channel
3323 * @NL80211_CHAN_WIDTH_40: 40 MHz channel, the %NL80211_ATTR_CENTER_FREQ1
3324 * attribute must be provided as well
3325 * @NL80211_CHAN_WIDTH_80: 80 MHz channel, the %NL80211_ATTR_CENTER_FREQ1
3326 * attribute must be provided as well
3327 * @NL80211_CHAN_WIDTH_80P80: 80+80 MHz channel, the %NL80211_ATTR_CENTER_FREQ1
3328 * and %NL80211_ATTR_CENTER_FREQ2 attributes must be provided as well
3329 * @NL80211_CHAN_WIDTH_160: 160 MHz channel, the %NL80211_ATTR_CENTER_FREQ1
3330 * attribute must be provided as well
3331 * @NL80211_CHAN_WIDTH_5: 5 MHz OFDM channel
3332 * @NL80211_CHAN_WIDTH_10: 10 MHz OFDM channel
3334 enum nl80211_chan_width {
3335 NL80211_CHAN_WIDTH_20_NOHT,
3336 NL80211_CHAN_WIDTH_20,
3337 NL80211_CHAN_WIDTH_40,
3338 NL80211_CHAN_WIDTH_80,
3339 NL80211_CHAN_WIDTH_80P80,
3340 NL80211_CHAN_WIDTH_160,
3341 NL80211_CHAN_WIDTH_5,
3342 NL80211_CHAN_WIDTH_10,
3346 * enum nl80211_bss_scan_width - control channel width for a BSS
3348 * These values are used with the %NL80211_BSS_CHAN_WIDTH attribute.
3350 * @NL80211_BSS_CHAN_WIDTH_20: control channel is 20 MHz wide or compatible
3351 * @NL80211_BSS_CHAN_WIDTH_10: control channel is 10 MHz wide
3352 * @NL80211_BSS_CHAN_WIDTH_5: control channel is 5 MHz wide
3354 enum nl80211_bss_scan_width {
3355 NL80211_BSS_CHAN_WIDTH_20,
3356 NL80211_BSS_CHAN_WIDTH_10,
3357 NL80211_BSS_CHAN_WIDTH_5,
3361 * enum nl80211_bss - netlink attributes for a BSS
3363 * @__NL80211_BSS_INVALID: invalid
3364 * @NL80211_BSS_BSSID: BSSID of the BSS (6 octets)
3365 * @NL80211_BSS_FREQUENCY: frequency in MHz (u32)
3366 * @NL80211_BSS_TSF: TSF of the received probe response/beacon (u64)
3367 * (if @NL80211_BSS_PRESP_DATA is present then this is known to be
3368 * from a probe response, otherwise it may be from the same beacon
3369 * that the NL80211_BSS_BEACON_TSF will be from)
3370 * @NL80211_BSS_BEACON_INTERVAL: beacon interval of the (I)BSS (u16)
3371 * @NL80211_BSS_CAPABILITY: capability field (CPU order, u16)
3372 * @NL80211_BSS_INFORMATION_ELEMENTS: binary attribute containing the
3373 * raw information elements from the probe response/beacon (bin);
3374 * if the %NL80211_BSS_BEACON_IES attribute is present and the data is
3375 * different then the IEs here are from a Probe Response frame; otherwise
3376 * they are from a Beacon frame.
3377 * However, if the driver does not indicate the source of the IEs, these
3378 * IEs may be from either frame subtype.
3379 * If present, the @NL80211_BSS_PRESP_DATA attribute indicates that the
3380 * data here is known to be from a probe response, without any heuristics.
3381 * @NL80211_BSS_SIGNAL_MBM: signal strength of probe response/beacon
3382 * in mBm (100 * dBm) (s32)
3383 * @NL80211_BSS_SIGNAL_UNSPEC: signal strength of the probe response/beacon
3384 * in unspecified units, scaled to 0..100 (u8)
3385 * @NL80211_BSS_STATUS: status, if this BSS is "used"
3386 * @NL80211_BSS_SEEN_MS_AGO: age of this BSS entry in ms
3387 * @NL80211_BSS_BEACON_IES: binary attribute containing the raw information
3388 * elements from a Beacon frame (bin); not present if no Beacon frame has
3390 * @NL80211_BSS_CHAN_WIDTH: channel width of the control channel
3391 * (u32, enum nl80211_bss_scan_width)
3392 * @NL80211_BSS_BEACON_TSF: TSF of the last received beacon (u64)
3393 * (not present if no beacon frame has been received yet)
3394 * @NL80211_BSS_PRESP_DATA: the data in @NL80211_BSS_INFORMATION_ELEMENTS and
3395 * @NL80211_BSS_TSF is known to be from a probe response (flag attribute)
3396 * @NL80211_BSS_LAST_SEEN_BOOTTIME: CLOCK_BOOTTIME timestamp when this entry
3397 * was last updated by a received frame. The value is expected to be
3398 * accurate to about 10ms. (u64, nanoseconds)
3399 * @__NL80211_BSS_AFTER_LAST: internal
3400 * @NL80211_BSS_MAX: highest BSS attribute
3403 __NL80211_BSS_INVALID,
3405 NL80211_BSS_FREQUENCY,
3407 NL80211_BSS_BEACON_INTERVAL,
3408 NL80211_BSS_CAPABILITY,
3409 NL80211_BSS_INFORMATION_ELEMENTS,
3410 NL80211_BSS_SIGNAL_MBM,
3411 NL80211_BSS_SIGNAL_UNSPEC,
3413 NL80211_BSS_SEEN_MS_AGO,
3414 NL80211_BSS_BEACON_IES,
3415 NL80211_BSS_CHAN_WIDTH,
3416 NL80211_BSS_BEACON_TSF,
3417 NL80211_BSS_PRESP_DATA,
3418 NL80211_BSS_LAST_SEEN_BOOTTIME,
3421 __NL80211_BSS_AFTER_LAST,
3422 NL80211_BSS_MAX = __NL80211_BSS_AFTER_LAST - 1
3426 * enum nl80211_bss_status - BSS "status"
3427 * @NL80211_BSS_STATUS_AUTHENTICATED: Authenticated with this BSS.
3428 * Note that this is no longer used since cfg80211 no longer
3429 * keeps track of whether or not authentication was done with
3431 * @NL80211_BSS_STATUS_ASSOCIATED: Associated with this BSS.
3432 * @NL80211_BSS_STATUS_IBSS_JOINED: Joined to this IBSS.
3434 * The BSS status is a BSS attribute in scan dumps, which
3435 * indicates the status the interface has wrt. this BSS.
3437 enum nl80211_bss_status {
3438 NL80211_BSS_STATUS_AUTHENTICATED,
3439 NL80211_BSS_STATUS_ASSOCIATED,
3440 NL80211_BSS_STATUS_IBSS_JOINED,
3444 * enum nl80211_auth_type - AuthenticationType
3446 * @NL80211_AUTHTYPE_OPEN_SYSTEM: Open System authentication
3447 * @NL80211_AUTHTYPE_SHARED_KEY: Shared Key authentication (WEP only)
3448 * @NL80211_AUTHTYPE_FT: Fast BSS Transition (IEEE 802.11r)
3449 * @NL80211_AUTHTYPE_NETWORK_EAP: Network EAP (some Cisco APs and mainly LEAP)
3450 * @NL80211_AUTHTYPE_SAE: Simultaneous authentication of equals
3451 * @__NL80211_AUTHTYPE_NUM: internal
3452 * @NL80211_AUTHTYPE_MAX: maximum valid auth algorithm
3453 * @NL80211_AUTHTYPE_AUTOMATIC: determine automatically (if necessary by
3454 * trying multiple times); this is invalid in netlink -- leave out
3455 * the attribute for this on CONNECT commands.
3457 enum nl80211_auth_type {
3458 NL80211_AUTHTYPE_OPEN_SYSTEM,
3459 NL80211_AUTHTYPE_SHARED_KEY,
3460 NL80211_AUTHTYPE_FT,
3461 NL80211_AUTHTYPE_NETWORK_EAP,
3462 NL80211_AUTHTYPE_SAE,
3465 __NL80211_AUTHTYPE_NUM,
3466 NL80211_AUTHTYPE_MAX = __NL80211_AUTHTYPE_NUM - 1,
3467 NL80211_AUTHTYPE_AUTOMATIC
3471 * enum nl80211_key_type - Key Type
3472 * @NL80211_KEYTYPE_GROUP: Group (broadcast/multicast) key
3473 * @NL80211_KEYTYPE_PAIRWISE: Pairwise (unicast/individual) key
3474 * @NL80211_KEYTYPE_PEERKEY: PeerKey (DLS)
3475 * @NUM_NL80211_KEYTYPES: number of defined key types
3477 enum nl80211_key_type {
3478 NL80211_KEYTYPE_GROUP,
3479 NL80211_KEYTYPE_PAIRWISE,
3480 NL80211_KEYTYPE_PEERKEY,
3482 NUM_NL80211_KEYTYPES
3486 * enum nl80211_mfp - Management frame protection state
3487 * @NL80211_MFP_NO: Management frame protection not used
3488 * @NL80211_MFP_REQUIRED: Management frame protection required
3492 NL80211_MFP_REQUIRED,
3495 enum nl80211_wpa_versions {
3496 NL80211_WPA_VERSION_1 = 1 << 0,
3497 NL80211_WPA_VERSION_2 = 1 << 1,
3501 * enum nl80211_key_default_types - key default types
3502 * @__NL80211_KEY_DEFAULT_TYPE_INVALID: invalid
3503 * @NL80211_KEY_DEFAULT_TYPE_UNICAST: key should be used as default
3505 * @NL80211_KEY_DEFAULT_TYPE_MULTICAST: key should be used as default
3507 * @NUM_NL80211_KEY_DEFAULT_TYPES: number of default types
3509 enum nl80211_key_default_types {
3510 __NL80211_KEY_DEFAULT_TYPE_INVALID,
3511 NL80211_KEY_DEFAULT_TYPE_UNICAST,
3512 NL80211_KEY_DEFAULT_TYPE_MULTICAST,
3514 NUM_NL80211_KEY_DEFAULT_TYPES
3518 * enum nl80211_key_attributes - key attributes
3519 * @__NL80211_KEY_INVALID: invalid
3520 * @NL80211_KEY_DATA: (temporal) key data; for TKIP this consists of
3521 * 16 bytes encryption key followed by 8 bytes each for TX and RX MIC
3523 * @NL80211_KEY_IDX: key ID (u8, 0-3)
3524 * @NL80211_KEY_CIPHER: key cipher suite (u32, as defined by IEEE 802.11
3525 * section 7.3.2.25.1, e.g. 0x000FAC04)
3526 * @NL80211_KEY_SEQ: transmit key sequence number (IV/PN) for TKIP and
3527 * CCMP keys, each six bytes in little endian
3528 * @NL80211_KEY_DEFAULT: flag indicating default key
3529 * @NL80211_KEY_DEFAULT_MGMT: flag indicating default management key
3530 * @NL80211_KEY_TYPE: the key type from enum nl80211_key_type, if not
3531 * specified the default depends on whether a MAC address was
3532 * given with the command using the key or not (u32)
3533 * @NL80211_KEY_DEFAULT_TYPES: A nested attribute containing flags
3534 * attributes, specifying what a key should be set as default as.
3535 * See &enum nl80211_key_default_types.
3536 * @__NL80211_KEY_AFTER_LAST: internal
3537 * @NL80211_KEY_MAX: highest key attribute
3539 enum nl80211_key_attributes {
3540 __NL80211_KEY_INVALID,
3545 NL80211_KEY_DEFAULT,
3546 NL80211_KEY_DEFAULT_MGMT,
3548 NL80211_KEY_DEFAULT_TYPES,
3551 __NL80211_KEY_AFTER_LAST,
3552 NL80211_KEY_MAX = __NL80211_KEY_AFTER_LAST - 1
3556 * enum nl80211_tx_rate_attributes - TX rate set attributes
3557 * @__NL80211_TXRATE_INVALID: invalid
3558 * @NL80211_TXRATE_LEGACY: Legacy (non-MCS) rates allowed for TX rate selection
3559 * in an array of rates as defined in IEEE 802.11 7.3.2.2 (u8 values with
3560 * 1 = 500 kbps) but without the IE length restriction (at most
3561 * %NL80211_MAX_SUPP_RATES in a single array).
3562 * @NL80211_TXRATE_HT: HT (MCS) rates allowed for TX rate selection
3563 * in an array of MCS numbers.
3564 * @NL80211_TXRATE_VHT: VHT rates allowed for TX rate selection,
3565 * see &struct nl80211_txrate_vht
3566 * @NL80211_TXRATE_GI: configure GI, see &enum nl80211_txrate_gi
3567 * @__NL80211_TXRATE_AFTER_LAST: internal
3568 * @NL80211_TXRATE_MAX: highest TX rate attribute
3570 enum nl80211_tx_rate_attributes {
3571 __NL80211_TXRATE_INVALID,
3572 NL80211_TXRATE_LEGACY,
3578 __NL80211_TXRATE_AFTER_LAST,
3579 NL80211_TXRATE_MAX = __NL80211_TXRATE_AFTER_LAST - 1
3582 #define NL80211_TXRATE_MCS NL80211_TXRATE_HT
3583 #define NL80211_VHT_NSS_MAX 8
3586 * struct nl80211_txrate_vht - VHT MCS/NSS txrate bitmap
3587 * @mcs: MCS bitmap table for each NSS (array index 0 for 1 stream, etc.)
3589 struct nl80211_txrate_vht {
3590 __u16 mcs[NL80211_VHT_NSS_MAX];
3593 enum nl80211_txrate_gi {
3594 NL80211_TXRATE_DEFAULT_GI,
3595 NL80211_TXRATE_FORCE_SGI,
3596 NL80211_TXRATE_FORCE_LGI,
3600 * enum nl80211_band - Frequency band
3601 * @NL80211_BAND_2GHZ: 2.4 GHz ISM band
3602 * @NL80211_BAND_5GHZ: around 5 GHz band (4.9 - 5.7 GHz)
3603 * @NL80211_BAND_60GHZ: around 60 GHz band (58.32 - 64.80 GHz)
3612 * enum nl80211_ps_state - powersave state
3613 * @NL80211_PS_DISABLED: powersave is disabled
3614 * @NL80211_PS_ENABLED: powersave is enabled
3616 enum nl80211_ps_state {
3617 NL80211_PS_DISABLED,
3622 * enum nl80211_attr_cqm - connection quality monitor attributes
3623 * @__NL80211_ATTR_CQM_INVALID: invalid
3624 * @NL80211_ATTR_CQM_RSSI_THOLD: RSSI threshold in dBm. This value specifies
3625 * the threshold for the RSSI level at which an event will be sent. Zero
3627 * @NL80211_ATTR_CQM_RSSI_HYST: RSSI hysteresis in dBm. This value specifies
3628 * the minimum amount the RSSI level must change after an event before a
3629 * new event may be issued (to reduce effects of RSSI oscillation).
3630 * @NL80211_ATTR_CQM_RSSI_THRESHOLD_EVENT: RSSI threshold event
3631 * @NL80211_ATTR_CQM_PKT_LOSS_EVENT: a u32 value indicating that this many
3632 * consecutive packets were not acknowledged by the peer
3633 * @NL80211_ATTR_CQM_TXE_RATE: TX error rate in %. Minimum % of TX failures
3634 * during the given %NL80211_ATTR_CQM_TXE_INTVL before an
3635 * %NL80211_CMD_NOTIFY_CQM with reported %NL80211_ATTR_CQM_TXE_RATE and
3636 * %NL80211_ATTR_CQM_TXE_PKTS is generated.
3637 * @NL80211_ATTR_CQM_TXE_PKTS: number of attempted packets in a given
3638 * %NL80211_ATTR_CQM_TXE_INTVL before %NL80211_ATTR_CQM_TXE_RATE is
3640 * @NL80211_ATTR_CQM_TXE_INTVL: interval in seconds. Specifies the periodic
3641 * interval in which %NL80211_ATTR_CQM_TXE_PKTS and
3642 * %NL80211_ATTR_CQM_TXE_RATE must be satisfied before generating an
3643 * %NL80211_CMD_NOTIFY_CQM. Set to 0 to turn off TX error reporting.
3644 * @NL80211_ATTR_CQM_BEACON_LOSS_EVENT: flag attribute that's set in a beacon
3646 * @__NL80211_ATTR_CQM_AFTER_LAST: internal
3647 * @NL80211_ATTR_CQM_MAX: highest key attribute
3649 enum nl80211_attr_cqm {
3650 __NL80211_ATTR_CQM_INVALID,
3651 NL80211_ATTR_CQM_RSSI_THOLD,
3652 NL80211_ATTR_CQM_RSSI_HYST,
3653 NL80211_ATTR_CQM_RSSI_THRESHOLD_EVENT,
3654 NL80211_ATTR_CQM_PKT_LOSS_EVENT,
3655 NL80211_ATTR_CQM_TXE_RATE,
3656 NL80211_ATTR_CQM_TXE_PKTS,
3657 NL80211_ATTR_CQM_TXE_INTVL,
3658 NL80211_ATTR_CQM_BEACON_LOSS_EVENT,
3661 __NL80211_ATTR_CQM_AFTER_LAST,
3662 NL80211_ATTR_CQM_MAX = __NL80211_ATTR_CQM_AFTER_LAST - 1
3666 * enum nl80211_cqm_rssi_threshold_event - RSSI threshold event
3667 * @NL80211_CQM_RSSI_THRESHOLD_EVENT_LOW: The RSSI level is lower than the
3668 * configured threshold
3669 * @NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH: The RSSI is higher than the
3670 * configured threshold
3671 * @NL80211_CQM_RSSI_BEACON_LOSS_EVENT: (reserved, never sent)
3673 enum nl80211_cqm_rssi_threshold_event {
3674 NL80211_CQM_RSSI_THRESHOLD_EVENT_LOW,
3675 NL80211_CQM_RSSI_THRESHOLD_EVENT_HIGH,
3676 NL80211_CQM_RSSI_BEACON_LOSS_EVENT,
3681 * enum nl80211_tx_power_setting - TX power adjustment
3682 * @NL80211_TX_POWER_AUTOMATIC: automatically determine transmit power
3683 * @NL80211_TX_POWER_LIMITED: limit TX power by the mBm parameter
3684 * @NL80211_TX_POWER_FIXED: fix TX power to the mBm parameter
3686 enum nl80211_tx_power_setting {
3687 NL80211_TX_POWER_AUTOMATIC,
3688 NL80211_TX_POWER_LIMITED,
3689 NL80211_TX_POWER_FIXED,
3693 * enum nl80211_packet_pattern_attr - packet pattern attribute
3694 * @__NL80211_PKTPAT_INVALID: invalid number for nested attribute
3695 * @NL80211_PKTPAT_PATTERN: the pattern, values where the mask has
3696 * a zero bit are ignored
3697 * @NL80211_PKTPAT_MASK: pattern mask, must be long enough to have
3698 * a bit for each byte in the pattern. The lowest-order bit corresponds
3699 * to the first byte of the pattern, but the bytes of the pattern are
3700 * in a little-endian-like format, i.e. the 9th byte of the pattern
3701 * corresponds to the lowest-order bit in the second byte of the mask.
3702 * For example: The match 00:xx:00:00:xx:00:00:00:00:xx:xx:xx (where
3703 * xx indicates "don't care") would be represented by a pattern of
3704 * twelve zero bytes, and a mask of "0xed,0x01".
3705 * Note that the pattern matching is done as though frames were not
3706 * 802.11 frames but 802.3 frames, i.e. the frame is fully unpacked
3707 * first (including SNAP header unpacking) and then matched.
3708 * @NL80211_PKTPAT_OFFSET: packet offset, pattern is matched after
3709 * these fixed number of bytes of received packet
3710 * @NUM_NL80211_PKTPAT: number of attributes
3711 * @MAX_NL80211_PKTPAT: max attribute number
3713 enum nl80211_packet_pattern_attr {
3714 __NL80211_PKTPAT_INVALID,
3715 NL80211_PKTPAT_MASK,
3716 NL80211_PKTPAT_PATTERN,
3717 NL80211_PKTPAT_OFFSET,
3720 MAX_NL80211_PKTPAT = NUM_NL80211_PKTPAT - 1,
3724 * struct nl80211_pattern_support - packet pattern support information
3725 * @max_patterns: maximum number of patterns supported
3726 * @min_pattern_len: minimum length of each pattern
3727 * @max_pattern_len: maximum length of each pattern
3728 * @max_pkt_offset: maximum Rx packet offset
3730 * This struct is carried in %NL80211_WOWLAN_TRIG_PKT_PATTERN when
3731 * that is part of %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED or in
3732 * %NL80211_ATTR_COALESCE_RULE_PKT_PATTERN when that is part of
3733 * %NL80211_ATTR_COALESCE_RULE in the capability information given
3734 * by the kernel to userspace.
3736 struct nl80211_pattern_support {
3738 __u32 min_pattern_len;
3739 __u32 max_pattern_len;
3740 __u32 max_pkt_offset;
3741 } __attribute__((packed));
3743 /* only for backward compatibility */
3744 #define __NL80211_WOWLAN_PKTPAT_INVALID __NL80211_PKTPAT_INVALID
3745 #define NL80211_WOWLAN_PKTPAT_MASK NL80211_PKTPAT_MASK
3746 #define NL80211_WOWLAN_PKTPAT_PATTERN NL80211_PKTPAT_PATTERN
3747 #define NL80211_WOWLAN_PKTPAT_OFFSET NL80211_PKTPAT_OFFSET
3748 #define NUM_NL80211_WOWLAN_PKTPAT NUM_NL80211_PKTPAT
3749 #define MAX_NL80211_WOWLAN_PKTPAT MAX_NL80211_PKTPAT
3750 #define nl80211_wowlan_pattern_support nl80211_pattern_support
3753 * enum nl80211_wowlan_triggers - WoWLAN trigger definitions
3754 * @__NL80211_WOWLAN_TRIG_INVALID: invalid number for nested attributes
3755 * @NL80211_WOWLAN_TRIG_ANY: wake up on any activity, do not really put
3756 * the chip into a special state -- works best with chips that have
3757 * support for low-power operation already (flag)
3758 * Note that this mode is incompatible with all of the others, if
3759 * any others are even supported by the device.
3760 * @NL80211_WOWLAN_TRIG_DISCONNECT: wake up on disconnect, the way disconnect
3761 * is detected is implementation-specific (flag)
3762 * @NL80211_WOWLAN_TRIG_MAGIC_PKT: wake up on magic packet (6x 0xff, followed
3763 * by 16 repetitions of MAC addr, anywhere in payload) (flag)
3764 * @NL80211_WOWLAN_TRIG_PKT_PATTERN: wake up on the specified packet patterns
3765 * which are passed in an array of nested attributes, each nested attribute
3766 * defining a with attributes from &struct nl80211_wowlan_trig_pkt_pattern.
3767 * Each pattern defines a wakeup packet. Packet offset is associated with
3768 * each pattern which is used while matching the pattern. The matching is
3769 * done on the MSDU, i.e. as though the packet was an 802.3 packet, so the
3770 * pattern matching is done after the packet is converted to the MSDU.
3772 * In %NL80211_ATTR_WOWLAN_TRIGGERS_SUPPORTED, it is a binary attribute
3773 * carrying a &struct nl80211_pattern_support.
3775 * When reporting wakeup. it is a u32 attribute containing the 0-based
3776 * index of the pattern that caused the wakeup, in the patterns passed
3777 * to the kernel when configuring.
3778 * @NL80211_WOWLAN_TRIG_GTK_REKEY_SUPPORTED: Not a real trigger, and cannot be
3779 * used when setting, used only to indicate that GTK rekeying is supported
3780 * by the device (flag)
3781 * @NL80211_WOWLAN_TRIG_GTK_REKEY_FAILURE: wake up on GTK rekey failure (if
3782 * done by the device) (flag)
3783 * @NL80211_WOWLAN_TRIG_EAP_IDENT_REQUEST: wake up on EAP Identity Request
3785 * @NL80211_WOWLAN_TRIG_4WAY_HANDSHAKE: wake up on 4-way handshake (flag)
3786 * @NL80211_WOWLAN_TRIG_RFKILL_RELEASE: wake up when rfkill is released
3787 * (on devices that have rfkill in the device) (flag)
3788 * @NL80211_WOWLAN_TRIG_WAKEUP_PKT_80211: For wakeup reporting only, contains
3789 * the 802.11 packet that caused the wakeup, e.g. a deauth frame. The frame
3790 * may be truncated, the @NL80211_WOWLAN_TRIG_WAKEUP_PKT_80211_LEN
3791 * attribute contains the original length.
3792 * @NL80211_WOWLAN_TRIG_WAKEUP_PKT_80211_LEN: Original length of the 802.11
3793 * packet, may be bigger than the @NL80211_WOWLAN_TRIG_WAKEUP_PKT_80211
3794 * attribute if the packet was truncated somewhere.
3795 * @NL80211_WOWLAN_TRIG_WAKEUP_PKT_8023: For wakeup reporting only, contains the
3796 * 802.11 packet that caused the wakeup, e.g. a magic packet. The frame may
3797 * be truncated, the @NL80211_WOWLAN_TRIG_WAKEUP_PKT_8023_LEN attribute
3798 * contains the original length.
3799 * @NL80211_WOWLAN_TRIG_WAKEUP_PKT_8023_LEN: Original length of the 802.3
3800 * packet, may be bigger than the @NL80211_WOWLAN_TRIG_WAKEUP_PKT_8023
3801 * attribute if the packet was truncated somewhere.
3802 * @NL80211_WOWLAN_TRIG_TCP_CONNECTION: TCP connection wake, see DOC section
3803 * "TCP connection wakeup" for more details. This is a nested attribute
3804 * containing the exact information for establishing and keeping alive
3805 * the TCP connection.
3806 * @NL80211_WOWLAN_TRIG_TCP_WAKEUP_MATCH: For wakeup reporting only, the
3807 * wakeup packet was received on the TCP connection
3808 * @NL80211_WOWLAN_TRIG_WAKEUP_TCP_CONNLOST: For wakeup reporting only, the
3809 * TCP connection was lost or failed to be established
3810 * @NL80211_WOWLAN_TRIG_WAKEUP_TCP_NOMORETOKENS: For wakeup reporting only,
3811 * the TCP connection ran out of tokens to use for data to send to the
3813 * @NL80211_WOWLAN_TRIG_NET_DETECT: wake up when a configured network
3814 * is detected. This is a nested attribute that contains the
3815 * same attributes used with @NL80211_CMD_START_SCHED_SCAN. It
3816 * specifies how the scan is performed (e.g. the interval, the
3817 * channels to scan and the initial delay) as well as the scan
3818 * results that will trigger a wake (i.e. the matchsets). This
3819 * attribute is also sent in a response to
3820 * @NL80211_CMD_GET_WIPHY, indicating the number of match sets
3821 * supported by the driver (u32).
3822 * @NL80211_WOWLAN_TRIG_NET_DETECT_RESULTS: nested attribute
3823 * containing an array with information about what triggered the
3824 * wake up. If no elements are present in the array, it means
3825 * that the information is not available. If more than one
3826 * element is present, it means that more than one match
3828 * Each element in the array is a nested attribute that contains
3829 * one optional %NL80211_ATTR_SSID attribute and one optional
3830 * %NL80211_ATTR_SCAN_FREQUENCIES attribute. At least one of
3831 * these attributes must be present. If
3832 * %NL80211_ATTR_SCAN_FREQUENCIES contains more than one
3833 * frequency, it means that the match occurred in more than one
3835 * @NUM_NL80211_WOWLAN_TRIG: number of wake on wireless triggers
3836 * @MAX_NL80211_WOWLAN_TRIG: highest wowlan trigger attribute number
3838 * These nested attributes are used to configure the wakeup triggers and
3839 * to report the wakeup reason(s).
3841 enum nl80211_wowlan_triggers {
3842 __NL80211_WOWLAN_TRIG_INVALID,
3843 NL80211_WOWLAN_TRIG_ANY,
3844 NL80211_WOWLAN_TRIG_DISCONNECT,
3845 NL80211_WOWLAN_TRIG_MAGIC_PKT,
3846 NL80211_WOWLAN_TRIG_PKT_PATTERN,
3847 NL80211_WOWLAN_TRIG_GTK_REKEY_SUPPORTED,
3848 NL80211_WOWLAN_TRIG_GTK_REKEY_FAILURE,
3849 NL80211_WOWLAN_TRIG_EAP_IDENT_REQUEST,
3850 NL80211_WOWLAN_TRIG_4WAY_HANDSHAKE,
3851 NL80211_WOWLAN_TRIG_RFKILL_RELEASE,
3852 NL80211_WOWLAN_TRIG_WAKEUP_PKT_80211,
3853 NL80211_WOWLAN_TRIG_WAKEUP_PKT_80211_LEN,
3854 NL80211_WOWLAN_TRIG_WAKEUP_PKT_8023,
3855 NL80211_WOWLAN_TRIG_WAKEUP_PKT_8023_LEN,
3856 NL80211_WOWLAN_TRIG_TCP_CONNECTION,
3857 NL80211_WOWLAN_TRIG_WAKEUP_TCP_MATCH,
3858 NL80211_WOWLAN_TRIG_WAKEUP_TCP_CONNLOST,
3859 NL80211_WOWLAN_TRIG_WAKEUP_TCP_NOMORETOKENS,
3860 NL80211_WOWLAN_TRIG_NET_DETECT,
3861 NL80211_WOWLAN_TRIG_NET_DETECT_RESULTS,
3864 NUM_NL80211_WOWLAN_TRIG,
3865 MAX_NL80211_WOWLAN_TRIG = NUM_NL80211_WOWLAN_TRIG - 1
3869 * DOC: TCP connection wakeup
3871 * Some devices can establish a TCP connection in order to be woken up by a
3872 * packet coming in from outside their network segment, or behind NAT. If
3873 * configured, the device will establish a TCP connection to the given
3874 * service, and periodically send data to that service. The first data
3875 * packet is usually transmitted after SYN/ACK, also ACKing the SYN/ACK.
3876 * The data packets can optionally include a (little endian) sequence
3877 * number (in the TCP payload!) that is generated by the device, and, also
3878 * optionally, a token from a list of tokens. This serves as a keep-alive
3879 * with the service, and for NATed connections, etc.
3881 * During this keep-alive period, the server doesn't send any data to the
3882 * client. When receiving data, it is compared against the wakeup pattern
3883 * (and mask) and if it matches, the host is woken up. Similarly, if the
3884 * connection breaks or cannot be established to start with, the host is
3887 * Developer's note: ARP offload is required for this, otherwise TCP
3888 * response packets might not go through correctly.
3892 * struct nl80211_wowlan_tcp_data_seq - WoWLAN TCP data sequence
3893 * @start: starting value
3894 * @offset: offset of sequence number in packet
3895 * @len: length of the sequence value to write, 1 through 4
3897 * Note: don't confuse with the TCP sequence number(s), this is for the
3898 * keepalive packet payload. The actual value is written into the packet
3901 struct nl80211_wowlan_tcp_data_seq {
3902 __u32 start, offset, len;
3906 * struct nl80211_wowlan_tcp_data_token - WoWLAN TCP data token config
3907 * @offset: offset of token in packet
3908 * @len: length of each token
3909 * @token_stream: stream of data to be used for the tokens, the length must
3910 * be a multiple of @len for this to make sense
3912 struct nl80211_wowlan_tcp_data_token {
3914 __u8 token_stream[];
3918 * struct nl80211_wowlan_tcp_data_token_feature - data token features
3919 * @min_len: minimum token length
3920 * @max_len: maximum token length
3921 * @bufsize: total available token buffer size (max size of @token_stream)
3923 struct nl80211_wowlan_tcp_data_token_feature {
3924 __u32 min_len, max_len, bufsize;
3928 * enum nl80211_wowlan_tcp_attrs - WoWLAN TCP connection parameters
3929 * @__NL80211_WOWLAN_TCP_INVALID: invalid number for nested attributes
3930 * @NL80211_WOWLAN_TCP_SRC_IPV4: source IPv4 address (in network byte order)
3931 * @NL80211_WOWLAN_TCP_DST_IPV4: destination IPv4 address
3932 * (in network byte order)
3933 * @NL80211_WOWLAN_TCP_DST_MAC: destination MAC address, this is given because
3934 * route lookup when configured might be invalid by the time we suspend,
3935 * and doing a route lookup when suspending is no longer possible as it
3936 * might require ARP querying.
3937 * @NL80211_WOWLAN_TCP_SRC_PORT: source port (u16); optional, if not given a
3938 * socket and port will be allocated
3939 * @NL80211_WOWLAN_TCP_DST_PORT: destination port (u16)
3940 * @NL80211_WOWLAN_TCP_DATA_PAYLOAD: data packet payload, at least one byte.
3941 * For feature advertising, a u32 attribute holding the maximum length
3942 * of the data payload.
3943 * @NL80211_WOWLAN_TCP_DATA_PAYLOAD_SEQ: data packet sequence configuration
3944 * (if desired), a &struct nl80211_wowlan_tcp_data_seq. For feature
3945 * advertising it is just a flag
3946 * @NL80211_WOWLAN_TCP_DATA_PAYLOAD_TOKEN: data packet token configuration,
3947 * see &struct nl80211_wowlan_tcp_data_token and for advertising see
3948 * &struct nl80211_wowlan_tcp_data_token_feature.
3949 * @NL80211_WOWLAN_TCP_DATA_INTERVAL: data interval in seconds, maximum
3950 * interval in feature advertising (u32)
3951 * @NL80211_WOWLAN_TCP_WAKE_PAYLOAD: wake packet payload, for advertising a
3952 * u32 attribute holding the maximum length
3953 * @NL80211_WOWLAN_TCP_WAKE_MASK: Wake packet payload mask, not used for
3954 * feature advertising. The mask works like @NL80211_PKTPAT_MASK
3955 * but on the TCP payload only.
3956 * @NUM_NL80211_WOWLAN_TCP: number of TCP attributes
3957 * @MAX_NL80211_WOWLAN_TCP: highest attribute number
3959 enum nl80211_wowlan_tcp_attrs {
3960 __NL80211_WOWLAN_TCP_INVALID,
3961 NL80211_WOWLAN_TCP_SRC_IPV4,
3962 NL80211_WOWLAN_TCP_DST_IPV4,
3963 NL80211_WOWLAN_TCP_DST_MAC,
3964 NL80211_WOWLAN_TCP_SRC_PORT,
3965 NL80211_WOWLAN_TCP_DST_PORT,
3966 NL80211_WOWLAN_TCP_DATA_PAYLOAD,
3967 NL80211_WOWLAN_TCP_DATA_PAYLOAD_SEQ,
3968 NL80211_WOWLAN_TCP_DATA_PAYLOAD_TOKEN,
3969 NL80211_WOWLAN_TCP_DATA_INTERVAL,
3970 NL80211_WOWLAN_TCP_WAKE_PAYLOAD,
3971 NL80211_WOWLAN_TCP_WAKE_MASK,
3974 NUM_NL80211_WOWLAN_TCP,
3975 MAX_NL80211_WOWLAN_TCP = NUM_NL80211_WOWLAN_TCP - 1
3979 * struct nl80211_coalesce_rule_support - coalesce rule support information
3980 * @max_rules: maximum number of rules supported
3981 * @pat: packet pattern support information
3982 * @max_delay: maximum supported coalescing delay in msecs
3984 * This struct is carried in %NL80211_ATTR_COALESCE_RULE in the
3985 * capability information given by the kernel to userspace.
3987 struct nl80211_coalesce_rule_support {
3989 struct nl80211_pattern_support pat;
3991 } __attribute__((packed));
3994 * enum nl80211_attr_coalesce_rule - coalesce rule attribute
3995 * @__NL80211_COALESCE_RULE_INVALID: invalid number for nested attribute
3996 * @NL80211_ATTR_COALESCE_RULE_DELAY: delay in msecs used for packet coalescing
3997 * @NL80211_ATTR_COALESCE_RULE_CONDITION: condition for packet coalescence,
3998 * see &enum nl80211_coalesce_condition.
3999 * @NL80211_ATTR_COALESCE_RULE_PKT_PATTERN: packet offset, pattern is matched
4000 * after these fixed number of bytes of received packet
4001 * @NUM_NL80211_ATTR_COALESCE_RULE: number of attributes
4002 * @NL80211_ATTR_COALESCE_RULE_MAX: max attribute number
4004 enum nl80211_attr_coalesce_rule {
4005 __NL80211_COALESCE_RULE_INVALID,
4006 NL80211_ATTR_COALESCE_RULE_DELAY,
4007 NL80211_ATTR_COALESCE_RULE_CONDITION,
4008 NL80211_ATTR_COALESCE_RULE_PKT_PATTERN,
4011 NUM_NL80211_ATTR_COALESCE_RULE,
4012 NL80211_ATTR_COALESCE_RULE_MAX = NUM_NL80211_ATTR_COALESCE_RULE - 1
4016 * enum nl80211_coalesce_condition - coalesce rule conditions
4017 * @NL80211_COALESCE_CONDITION_MATCH: coalaesce Rx packets when patterns
4018 * in a rule are matched.
4019 * @NL80211_COALESCE_CONDITION_NO_MATCH: coalesce Rx packets when patterns
4020 * in a rule are not matched.
4022 enum nl80211_coalesce_condition {
4023 NL80211_COALESCE_CONDITION_MATCH,
4024 NL80211_COALESCE_CONDITION_NO_MATCH
4028 * enum nl80211_iface_limit_attrs - limit attributes
4029 * @NL80211_IFACE_LIMIT_UNSPEC: (reserved)
4030 * @NL80211_IFACE_LIMIT_MAX: maximum number of interfaces that
4031 * can be chosen from this set of interface types (u32)
4032 * @NL80211_IFACE_LIMIT_TYPES: nested attribute containing a
4033 * flag attribute for each interface type in this set
4034 * @NUM_NL80211_IFACE_LIMIT: number of attributes
4035 * @MAX_NL80211_IFACE_LIMIT: highest attribute number
4037 enum nl80211_iface_limit_attrs {
4038 NL80211_IFACE_LIMIT_UNSPEC,
4039 NL80211_IFACE_LIMIT_MAX,
4040 NL80211_IFACE_LIMIT_TYPES,
4043 NUM_NL80211_IFACE_LIMIT,
4044 MAX_NL80211_IFACE_LIMIT = NUM_NL80211_IFACE_LIMIT - 1
4048 * enum nl80211_if_combination_attrs -- interface combination attributes
4050 * @NL80211_IFACE_COMB_UNSPEC: (reserved)
4051 * @NL80211_IFACE_COMB_LIMITS: Nested attributes containing the limits
4052 * for given interface types, see &enum nl80211_iface_limit_attrs.
4053 * @NL80211_IFACE_COMB_MAXNUM: u32 attribute giving the total number of
4054 * interfaces that can be created in this group. This number doesn't
4055 * apply to interfaces purely managed in software, which are listed
4056 * in a separate attribute %NL80211_ATTR_INTERFACES_SOFTWARE.
4057 * @NL80211_IFACE_COMB_STA_AP_BI_MATCH: flag attribute specifying that
4058 * beacon intervals within this group must be all the same even for
4059 * infrastructure and AP/GO combinations, i.e. the GO(s) must adopt
4060 * the infrastructure network's beacon interval.
4061 * @NL80211_IFACE_COMB_NUM_CHANNELS: u32 attribute specifying how many
4062 * different channels may be used within this group.
4063 * @NL80211_IFACE_COMB_RADAR_DETECT_WIDTHS: u32 attribute containing the bitmap
4064 * of supported channel widths for radar detection.
4065 * @NL80211_IFACE_COMB_RADAR_DETECT_REGIONS: u32 attribute containing the bitmap
4066 * of supported regulatory regions for radar detection.
4067 * @NUM_NL80211_IFACE_COMB: number of attributes
4068 * @MAX_NL80211_IFACE_COMB: highest attribute number
4071 * limits = [ #{STA} <= 1, #{AP} <= 1 ], matching BI, channels = 1, max = 2
4072 * => allows an AP and a STA that must match BIs
4074 * numbers = [ #{AP, P2P-GO} <= 8 ], channels = 1, max = 8
4075 * => allows 8 of AP/GO
4077 * numbers = [ #{STA} <= 2 ], channels = 2, max = 2
4078 * => allows two STAs on different channels
4080 * numbers = [ #{STA} <= 1, #{P2P-client,P2P-GO} <= 3 ], max = 4
4081 * => allows a STA plus three P2P interfaces
4083 * The list of these four possiblities could completely be contained
4084 * within the %NL80211_ATTR_INTERFACE_COMBINATIONS attribute to indicate
4085 * that any of these groups must match.
4087 * "Combinations" of just a single interface will not be listed here,
4088 * a single interface of any valid interface type is assumed to always
4089 * be possible by itself. This means that implicitly, for each valid
4090 * interface type, the following group always exists:
4091 * numbers = [ #{<type>} <= 1 ], channels = 1, max = 1
4093 enum nl80211_if_combination_attrs {
4094 NL80211_IFACE_COMB_UNSPEC,
4095 NL80211_IFACE_COMB_LIMITS,
4096 NL80211_IFACE_COMB_MAXNUM,
4097 NL80211_IFACE_COMB_STA_AP_BI_MATCH,
4098 NL80211_IFACE_COMB_NUM_CHANNELS,
4099 NL80211_IFACE_COMB_RADAR_DETECT_WIDTHS,
4100 NL80211_IFACE_COMB_RADAR_DETECT_REGIONS,
4103 NUM_NL80211_IFACE_COMB,
4104 MAX_NL80211_IFACE_COMB = NUM_NL80211_IFACE_COMB - 1
4109 * enum nl80211_plink_state - state of a mesh peer link finite state machine
4111 * @NL80211_PLINK_LISTEN: initial state, considered the implicit
4112 * state of non existant mesh peer links
4113 * @NL80211_PLINK_OPN_SNT: mesh plink open frame has been sent to
4115 * @NL80211_PLINK_OPN_RCVD: mesh plink open frame has been received
4116 * from this mesh peer
4117 * @NL80211_PLINK_CNF_RCVD: mesh plink confirm frame has been
4118 * received from this mesh peer
4119 * @NL80211_PLINK_ESTAB: mesh peer link is established
4120 * @NL80211_PLINK_HOLDING: mesh peer link is being closed or cancelled
4121 * @NL80211_PLINK_BLOCKED: all frames transmitted from this mesh
4122 * plink are discarded
4123 * @NUM_NL80211_PLINK_STATES: number of peer link states
4124 * @MAX_NL80211_PLINK_STATES: highest numerical value of plink states
4126 enum nl80211_plink_state {
4127 NL80211_PLINK_LISTEN,
4128 NL80211_PLINK_OPN_SNT,
4129 NL80211_PLINK_OPN_RCVD,
4130 NL80211_PLINK_CNF_RCVD,
4131 NL80211_PLINK_ESTAB,
4132 NL80211_PLINK_HOLDING,
4133 NL80211_PLINK_BLOCKED,
4136 NUM_NL80211_PLINK_STATES,
4137 MAX_NL80211_PLINK_STATES = NUM_NL80211_PLINK_STATES - 1
4141 * enum nl80211_plink_action - actions to perform in mesh peers
4143 * @NL80211_PLINK_ACTION_NO_ACTION: perform no action
4144 * @NL80211_PLINK_ACTION_OPEN: start mesh peer link establishment
4145 * @NL80211_PLINK_ACTION_BLOCK: block traffic from this mesh peer
4146 * @NUM_NL80211_PLINK_ACTIONS: number of possible actions
4148 enum plink_actions {
4149 NL80211_PLINK_ACTION_NO_ACTION,
4150 NL80211_PLINK_ACTION_OPEN,
4151 NL80211_PLINK_ACTION_BLOCK,
4153 NUM_NL80211_PLINK_ACTIONS,
4157 #define NL80211_KCK_LEN 16
4158 #define NL80211_KEK_LEN 16
4159 #define NL80211_REPLAY_CTR_LEN 8
4162 * enum nl80211_rekey_data - attributes for GTK rekey offload
4163 * @__NL80211_REKEY_DATA_INVALID: invalid number for nested attributes
4164 * @NL80211_REKEY_DATA_KEK: key encryption key (binary)
4165 * @NL80211_REKEY_DATA_KCK: key confirmation key (binary)
4166 * @NL80211_REKEY_DATA_REPLAY_CTR: replay counter (binary)
4167 * @NUM_NL80211_REKEY_DATA: number of rekey attributes (internal)
4168 * @MAX_NL80211_REKEY_DATA: highest rekey attribute (internal)
4170 enum nl80211_rekey_data {
4171 __NL80211_REKEY_DATA_INVALID,
4172 NL80211_REKEY_DATA_KEK,
4173 NL80211_REKEY_DATA_KCK,
4174 NL80211_REKEY_DATA_REPLAY_CTR,
4177 NUM_NL80211_REKEY_DATA,
4178 MAX_NL80211_REKEY_DATA = NUM_NL80211_REKEY_DATA - 1
4182 * enum nl80211_hidden_ssid - values for %NL80211_ATTR_HIDDEN_SSID
4183 * @NL80211_HIDDEN_SSID_NOT_IN_USE: do not hide SSID (i.e., broadcast it in
4185 * @NL80211_HIDDEN_SSID_ZERO_LEN: hide SSID by using zero-length SSID element
4187 * @NL80211_HIDDEN_SSID_ZERO_CONTENTS: hide SSID by using correct length of SSID
4188 * element in Beacon frames but zero out each byte in the SSID
4190 enum nl80211_hidden_ssid {
4191 NL80211_HIDDEN_SSID_NOT_IN_USE,
4192 NL80211_HIDDEN_SSID_ZERO_LEN,
4193 NL80211_HIDDEN_SSID_ZERO_CONTENTS
4197 * enum nl80211_sta_wme_attr - station WME attributes
4198 * @__NL80211_STA_WME_INVALID: invalid number for nested attribute
4199 * @NL80211_STA_WME_UAPSD_QUEUES: bitmap of uapsd queues. the format
4200 * is the same as the AC bitmap in the QoS info field.
4201 * @NL80211_STA_WME_MAX_SP: max service period. the format is the same
4202 * as the MAX_SP field in the QoS info field (but already shifted down).
4203 * @__NL80211_STA_WME_AFTER_LAST: internal
4204 * @NL80211_STA_WME_MAX: highest station WME attribute
4206 enum nl80211_sta_wme_attr {
4207 __NL80211_STA_WME_INVALID,
4208 NL80211_STA_WME_UAPSD_QUEUES,
4209 NL80211_STA_WME_MAX_SP,
4212 __NL80211_STA_WME_AFTER_LAST,
4213 NL80211_STA_WME_MAX = __NL80211_STA_WME_AFTER_LAST - 1
4217 * enum nl80211_pmksa_candidate_attr - attributes for PMKSA caching candidates
4218 * @__NL80211_PMKSA_CANDIDATE_INVALID: invalid number for nested attributes
4219 * @NL80211_PMKSA_CANDIDATE_INDEX: candidate index (u32; the smaller, the higher
4221 * @NL80211_PMKSA_CANDIDATE_BSSID: candidate BSSID (6 octets)
4222 * @NL80211_PMKSA_CANDIDATE_PREAUTH: RSN pre-authentication supported (flag)
4223 * @NUM_NL80211_PMKSA_CANDIDATE: number of PMKSA caching candidate attributes
4225 * @MAX_NL80211_PMKSA_CANDIDATE: highest PMKSA caching candidate attribute
4228 enum nl80211_pmksa_candidate_attr {
4229 __NL80211_PMKSA_CANDIDATE_INVALID,
4230 NL80211_PMKSA_CANDIDATE_INDEX,
4231 NL80211_PMKSA_CANDIDATE_BSSID,
4232 NL80211_PMKSA_CANDIDATE_PREAUTH,
4235 NUM_NL80211_PMKSA_CANDIDATE,
4236 MAX_NL80211_PMKSA_CANDIDATE = NUM_NL80211_PMKSA_CANDIDATE - 1
4240 * enum nl80211_tdls_operation - values for %NL80211_ATTR_TDLS_OPERATION
4241 * @NL80211_TDLS_DISCOVERY_REQ: Send a TDLS discovery request
4242 * @NL80211_TDLS_SETUP: Setup TDLS link
4243 * @NL80211_TDLS_TEARDOWN: Teardown a TDLS link which is already established
4244 * @NL80211_TDLS_ENABLE_LINK: Enable TDLS link
4245 * @NL80211_TDLS_DISABLE_LINK: Disable TDLS link
4247 enum nl80211_tdls_operation {
4248 NL80211_TDLS_DISCOVERY_REQ,
4250 NL80211_TDLS_TEARDOWN,
4251 NL80211_TDLS_ENABLE_LINK,
4252 NL80211_TDLS_DISABLE_LINK,
4256 * enum nl80211_ap_sme_features - device-integrated AP features
4257 * Reserved for future use, no bits are defined in
4258 * NL80211_ATTR_DEVICE_AP_SME yet.
4259 enum nl80211_ap_sme_features {
4264 * enum nl80211_feature_flags - device/driver features
4265 * @NL80211_FEATURE_SK_TX_STATUS: This driver supports reflecting back
4266 * TX status to the socket error queue when requested with the
4268 * @NL80211_FEATURE_HT_IBSS: This driver supports IBSS with HT datarates.
4269 * @NL80211_FEATURE_INACTIVITY_TIMER: This driver takes care of freeing up
4270 * the connected inactive stations in AP mode.
4271 * @NL80211_FEATURE_CELL_BASE_REG_HINTS: This driver has been tested
4272 * to work properly to suppport receiving regulatory hints from
4273 * cellular base stations.
4274 * @NL80211_FEATURE_P2P_DEVICE_NEEDS_CHANNEL: (no longer available, only
4275 * here to reserve the value for API/ABI compatibility)
4276 * @NL80211_FEATURE_SAE: This driver supports simultaneous authentication of
4277 * equals (SAE) with user space SME (NL80211_CMD_AUTHENTICATE) in station
4279 * @NL80211_FEATURE_LOW_PRIORITY_SCAN: This driver supports low priority scan
4280 * @NL80211_FEATURE_SCAN_FLUSH: Scan flush is supported
4281 * @NL80211_FEATURE_AP_SCAN: Support scanning using an AP vif
4282 * @NL80211_FEATURE_VIF_TXPOWER: The driver supports per-vif TX power setting
4283 * @NL80211_FEATURE_NEED_OBSS_SCAN: The driver expects userspace to perform
4284 * OBSS scans and generate 20/40 BSS coex reports. This flag is used only
4285 * for drivers implementing the CONNECT API, for AUTH/ASSOC it is implied.
4286 * @NL80211_FEATURE_P2P_GO_CTWIN: P2P GO implementation supports CT Window
4288 * @NL80211_FEATURE_P2P_GO_OPPPS: P2P GO implementation supports opportunistic
4290 * @NL80211_FEATURE_FULL_AP_CLIENT_STATE: The driver supports full state
4291 * transitions for AP clients. Without this flag (and if the driver
4292 * doesn't have the AP SME in the device) the driver supports adding
4293 * stations only when they're associated and adds them in associated
4294 * state (to later be transitioned into authorized), with this flag
4295 * they should be added before even sending the authentication reply
4296 * and then transitioned into authenticated, associated and authorized
4297 * states using station flags.
4298 * Note that even for drivers that support this, the default is to add
4299 * stations in authenticated/associated state, so to add unauthenticated
4300 * stations the authenticated/associated bits have to be set in the mask.
4301 * @NL80211_FEATURE_ADVERTISE_CHAN_LIMITS: cfg80211 advertises channel limits
4302 * (HT40, VHT 80/160 MHz) if this flag is set
4303 * @NL80211_FEATURE_USERSPACE_MPM: This driver supports a userspace Mesh
4304 * Peering Management entity which may be implemented by registering for
4305 * beacons or NL80211_CMD_NEW_PEER_CANDIDATE events. The mesh beacon is
4306 * still generated by the driver.
4307 * @NL80211_FEATURE_ACTIVE_MONITOR: This driver supports an active monitor
4308 * interface. An active monitor interface behaves like a normal monitor
4309 * interface, but gets added to the driver. It ensures that incoming
4310 * unicast packets directed at the configured interface address get ACKed.
4311 * @NL80211_FEATURE_AP_MODE_CHAN_WIDTH_CHANGE: This driver supports dynamic
4312 * channel bandwidth change (e.g., HT 20 <-> 40 MHz channel) during the
4313 * lifetime of a BSS.
4314 * @NL80211_FEATURE_DS_PARAM_SET_IE_IN_PROBES: This device adds a DS Parameter
4315 * Set IE to probe requests.
4316 * @NL80211_FEATURE_WFA_TPC_IE_IN_PROBES: This device adds a WFA TPC Report IE
4317 * to probe requests.
4318 * @NL80211_FEATURE_QUIET: This device, in client mode, supports Quiet Period
4319 * requests sent to it by an AP.
4320 * @NL80211_FEATURE_TX_POWER_INSERTION: This device is capable of inserting the
4321 * current tx power value into the TPC Report IE in the spectrum
4322 * management TPC Report action frame, and in the Radio Measurement Link
4323 * Measurement Report action frame.
4324 * @NL80211_FEATURE_ACKTO_ESTIMATION: This driver supports dynamic ACK timeout
4325 * estimation (dynack). %NL80211_ATTR_WIPHY_DYN_ACK flag attribute is used
4327 * @NL80211_FEATURE_STATIC_SMPS: Device supports static spatial
4328 * multiplexing powersave, ie. can turn off all but one chain
4329 * even on HT connections that should be using more chains.
4330 * @NL80211_FEATURE_DYNAMIC_SMPS: Device supports dynamic spatial
4331 * multiplexing powersave, ie. can turn off all but one chain
4332 * and then wake the rest up as required after, for example,
4333 * rts/cts handshake.
4334 * @NL80211_FEATURE_SUPPORTS_WMM_ADMISSION: the device supports setting up WMM
4335 * TSPEC sessions (TID aka TSID 0-7) with the %NL80211_CMD_ADD_TX_TS
4336 * command. Standard IEEE 802.11 TSPEC setup is not yet supported, it
4337 * needs to be able to handle Block-Ack agreements and other things.
4338 * @NL80211_FEATURE_MAC_ON_CREATE: Device supports configuring
4339 * the vif's MAC address upon creation.
4340 * See 'macaddr' field in the vif_params (cfg80211.h).
4341 * @NL80211_FEATURE_TDLS_CHANNEL_SWITCH: Driver supports channel switching when
4342 * operating as a TDLS peer.
4343 * @NL80211_FEATURE_SCAN_RANDOM_MAC_ADDR: This device/driver supports using a
4344 * random MAC address during scan (if the device is unassociated); the
4345 * %NL80211_SCAN_FLAG_RANDOM_ADDR flag may be set for scans and the MAC
4346 * address mask/value will be used.
4347 * @NL80211_FEATURE_SCHED_SCAN_RANDOM_MAC_ADDR: This device/driver supports
4348 * using a random MAC address for every scan iteration during scheduled
4349 * scan (while not associated), the %NL80211_SCAN_FLAG_RANDOM_ADDR may
4350 * be set for scheduled scan and the MAC address mask/value will be used.
4351 * @NL80211_FEATURE_ND_RANDOM_MAC_ADDR: This device/driver supports using a
4352 * random MAC address for every scan iteration during "net detect", i.e.
4353 * scan in unassociated WoWLAN, the %NL80211_SCAN_FLAG_RANDOM_ADDR may
4354 * be set for scheduled scan and the MAC address mask/value will be used.
4356 enum nl80211_feature_flags {
4357 NL80211_FEATURE_SK_TX_STATUS = 1 << 0,
4358 NL80211_FEATURE_HT_IBSS = 1 << 1,
4359 NL80211_FEATURE_INACTIVITY_TIMER = 1 << 2,
4360 NL80211_FEATURE_CELL_BASE_REG_HINTS = 1 << 3,
4361 NL80211_FEATURE_P2P_DEVICE_NEEDS_CHANNEL = 1 << 4,
4362 NL80211_FEATURE_SAE = 1 << 5,
4363 NL80211_FEATURE_LOW_PRIORITY_SCAN = 1 << 6,
4364 NL80211_FEATURE_SCAN_FLUSH = 1 << 7,
4365 NL80211_FEATURE_AP_SCAN = 1 << 8,
4366 NL80211_FEATURE_VIF_TXPOWER = 1 << 9,
4367 NL80211_FEATURE_NEED_OBSS_SCAN = 1 << 10,
4368 NL80211_FEATURE_P2P_GO_CTWIN = 1 << 11,
4369 NL80211_FEATURE_P2P_GO_OPPPS = 1 << 12,
4370 /* bit 13 is reserved */
4371 NL80211_FEATURE_ADVERTISE_CHAN_LIMITS = 1 << 14,
4372 NL80211_FEATURE_FULL_AP_CLIENT_STATE = 1 << 15,
4373 NL80211_FEATURE_USERSPACE_MPM = 1 << 16,
4374 NL80211_FEATURE_ACTIVE_MONITOR = 1 << 17,
4375 NL80211_FEATURE_AP_MODE_CHAN_WIDTH_CHANGE = 1 << 18,
4376 NL80211_FEATURE_DS_PARAM_SET_IE_IN_PROBES = 1 << 19,
4377 NL80211_FEATURE_WFA_TPC_IE_IN_PROBES = 1 << 20,
4378 NL80211_FEATURE_QUIET = 1 << 21,
4379 NL80211_FEATURE_TX_POWER_INSERTION = 1 << 22,
4380 NL80211_FEATURE_ACKTO_ESTIMATION = 1 << 23,
4381 NL80211_FEATURE_STATIC_SMPS = 1 << 24,
4382 NL80211_FEATURE_DYNAMIC_SMPS = 1 << 25,
4383 NL80211_FEATURE_SUPPORTS_WMM_ADMISSION = 1 << 26,
4384 NL80211_FEATURE_MAC_ON_CREATE = 1 << 27,
4385 NL80211_FEATURE_TDLS_CHANNEL_SWITCH = 1 << 28,
4386 NL80211_FEATURE_SCAN_RANDOM_MAC_ADDR = 1 << 29,
4387 NL80211_FEATURE_SCHED_SCAN_RANDOM_MAC_ADDR = 1 << 30,
4388 NL80211_FEATURE_ND_RANDOM_MAC_ADDR = 1 << 31,
4392 * enum nl80211_ext_feature_index - bit index of extended features.
4393 * @NL80211_EXT_FEATURE_VHT_IBSS: This driver supports IBSS with VHT datarates.
4395 * @NUM_NL80211_EXT_FEATURES: number of extended features.
4396 * @MAX_NL80211_EXT_FEATURES: highest extended feature index.
4398 enum nl80211_ext_feature_index {
4399 NL80211_EXT_FEATURE_VHT_IBSS,
4401 /* add new features before the definition below */
4402 NUM_NL80211_EXT_FEATURES,
4403 MAX_NL80211_EXT_FEATURES = NUM_NL80211_EXT_FEATURES - 1
4407 * enum nl80211_probe_resp_offload_support_attr - optional supported
4408 * protocols for probe-response offloading by the driver/FW.
4409 * To be used with the %NL80211_ATTR_PROBE_RESP_OFFLOAD attribute.
4410 * Each enum value represents a bit in the bitmap of supported
4411 * protocols. Typically a subset of probe-requests belonging to a
4412 * supported protocol will be excluded from offload and uploaded
4415 * @NL80211_PROBE_RESP_OFFLOAD_SUPPORT_WPS: Support for WPS ver. 1
4416 * @NL80211_PROBE_RESP_OFFLOAD_SUPPORT_WPS2: Support for WPS ver. 2
4417 * @NL80211_PROBE_RESP_OFFLOAD_SUPPORT_P2P: Support for P2P
4418 * @NL80211_PROBE_RESP_OFFLOAD_SUPPORT_80211U: Support for 802.11u
4420 enum nl80211_probe_resp_offload_support_attr {
4421 NL80211_PROBE_RESP_OFFLOAD_SUPPORT_WPS = 1<<0,
4422 NL80211_PROBE_RESP_OFFLOAD_SUPPORT_WPS2 = 1<<1,
4423 NL80211_PROBE_RESP_OFFLOAD_SUPPORT_P2P = 1<<2,
4424 NL80211_PROBE_RESP_OFFLOAD_SUPPORT_80211U = 1<<3,
4428 * enum nl80211_connect_failed_reason - connection request failed reasons
4429 * @NL80211_CONN_FAIL_MAX_CLIENTS: Maximum number of clients that can be
4430 * handled by the AP is reached.
4431 * @NL80211_CONN_FAIL_BLOCKED_CLIENT: Connection request is rejected due to ACL.
4433 enum nl80211_connect_failed_reason {
4434 NL80211_CONN_FAIL_MAX_CLIENTS,
4435 NL80211_CONN_FAIL_BLOCKED_CLIENT,
4439 * enum nl80211_scan_flags - scan request control flags
4441 * Scan request control flags are used to control the handling
4442 * of NL80211_CMD_TRIGGER_SCAN and NL80211_CMD_START_SCHED_SCAN
4445 * @NL80211_SCAN_FLAG_LOW_PRIORITY: scan request has low priority
4446 * @NL80211_SCAN_FLAG_FLUSH: flush cache before scanning
4447 * @NL80211_SCAN_FLAG_AP: force a scan even if the interface is configured
4448 * as AP and the beaconing has already been configured. This attribute is
4449 * dangerous because will destroy stations performance as a lot of frames
4450 * will be lost while scanning off-channel, therefore it must be used only
4451 * when really needed
4452 * @NL80211_SCAN_FLAG_RANDOM_ADDR: use a random MAC address for this scan (or
4453 * for scheduled scan: a different one for every scan iteration). When the
4454 * flag is set, depending on device capabilities the @NL80211_ATTR_MAC and
4455 * @NL80211_ATTR_MAC_MASK attributes may also be given in which case only
4456 * the masked bits will be preserved from the MAC address and the remainder
4457 * randomised. If the attributes are not given full randomisation (46 bits,
4458 * locally administered 1, multicast 0) is assumed.
4459 * This flag must not be requested when the feature isn't supported, check
4460 * the nl80211 feature flags for the device.
4462 enum nl80211_scan_flags {
4463 NL80211_SCAN_FLAG_LOW_PRIORITY = 1<<0,
4464 NL80211_SCAN_FLAG_FLUSH = 1<<1,
4465 NL80211_SCAN_FLAG_AP = 1<<2,
4466 NL80211_SCAN_FLAG_RANDOM_ADDR = 1<<3,
4470 * enum nl80211_acl_policy - access control policy
4472 * Access control policy is applied on a MAC list set by
4473 * %NL80211_CMD_START_AP and %NL80211_CMD_SET_MAC_ACL, to
4474 * be used with %NL80211_ATTR_ACL_POLICY.
4476 * @NL80211_ACL_POLICY_ACCEPT_UNLESS_LISTED: Deny stations which are
4477 * listed in ACL, i.e. allow all the stations which are not listed
4478 * in ACL to authenticate.
4479 * @NL80211_ACL_POLICY_DENY_UNLESS_LISTED: Allow the stations which are listed
4480 * in ACL, i.e. deny all the stations which are not listed in ACL.
4482 enum nl80211_acl_policy {
4483 NL80211_ACL_POLICY_ACCEPT_UNLESS_LISTED,
4484 NL80211_ACL_POLICY_DENY_UNLESS_LISTED,
4488 * enum nl80211_smps_mode - SMPS mode
4490 * Requested SMPS mode (for AP mode)
4492 * @NL80211_SMPS_OFF: SMPS off (use all antennas).
4493 * @NL80211_SMPS_STATIC: static SMPS (use a single antenna)
4494 * @NL80211_SMPS_DYNAMIC: dynamic smps (start with a single antenna and
4495 * turn on other antennas after CTS/RTS).
4497 enum nl80211_smps_mode {
4499 NL80211_SMPS_STATIC,
4500 NL80211_SMPS_DYNAMIC,
4502 __NL80211_SMPS_AFTER_LAST,
4503 NL80211_SMPS_MAX = __NL80211_SMPS_AFTER_LAST - 1
4507 * enum nl80211_radar_event - type of radar event for DFS operation
4509 * Type of event to be used with NL80211_ATTR_RADAR_EVENT to inform userspace
4510 * about detected radars or success of the channel available check (CAC)
4512 * @NL80211_RADAR_DETECTED: A radar pattern has been detected. The channel is
4514 * @NL80211_RADAR_CAC_FINISHED: Channel Availability Check has been finished,
4515 * the channel is now available.
4516 * @NL80211_RADAR_CAC_ABORTED: Channel Availability Check has been aborted, no
4517 * change to the channel status.
4518 * @NL80211_RADAR_NOP_FINISHED: The Non-Occupancy Period for this channel is
4519 * over, channel becomes usable.
4521 enum nl80211_radar_event {
4522 NL80211_RADAR_DETECTED,
4523 NL80211_RADAR_CAC_FINISHED,
4524 NL80211_RADAR_CAC_ABORTED,
4525 NL80211_RADAR_NOP_FINISHED,
4529 * enum nl80211_dfs_state - DFS states for channels
4531 * Channel states used by the DFS code.
4533 * @NL80211_DFS_USABLE: The channel can be used, but channel availability
4534 * check (CAC) must be performed before using it for AP or IBSS.
4535 * @NL80211_DFS_UNAVAILABLE: A radar has been detected on this channel, it
4536 * is therefore marked as not available.
4537 * @NL80211_DFS_AVAILABLE: The channel has been CAC checked and is available.
4539 enum nl80211_dfs_state {
4541 NL80211_DFS_UNAVAILABLE,
4542 NL80211_DFS_AVAILABLE,
4546 * enum enum nl80211_protocol_features - nl80211 protocol features
4547 * @NL80211_PROTOCOL_FEATURE_SPLIT_WIPHY_DUMP: nl80211 supports splitting
4548 * wiphy dumps (if requested by the application with the attribute
4549 * %NL80211_ATTR_SPLIT_WIPHY_DUMP. Also supported is filtering the
4550 * wiphy dump by %NL80211_ATTR_WIPHY, %NL80211_ATTR_IFINDEX or
4551 * %NL80211_ATTR_WDEV.
4553 enum nl80211_protocol_features {
4554 NL80211_PROTOCOL_FEATURE_SPLIT_WIPHY_DUMP = 1 << 0,
4558 * enum nl80211_crit_proto_id - nl80211 critical protocol identifiers
4560 * @NL80211_CRIT_PROTO_UNSPEC: protocol unspecified.
4561 * @NL80211_CRIT_PROTO_DHCP: BOOTP or DHCPv6 protocol.
4562 * @NL80211_CRIT_PROTO_EAPOL: EAPOL protocol.
4563 * @NL80211_CRIT_PROTO_APIPA: APIPA protocol.
4564 * @NUM_NL80211_CRIT_PROTO: must be kept last.
4566 enum nl80211_crit_proto_id {
4567 NL80211_CRIT_PROTO_UNSPEC,
4568 NL80211_CRIT_PROTO_DHCP,
4569 NL80211_CRIT_PROTO_EAPOL,
4570 NL80211_CRIT_PROTO_APIPA,
4571 /* add other protocols before this one */
4572 NUM_NL80211_CRIT_PROTO
4575 /* maximum duration for critical protocol measures */
4576 #define NL80211_CRIT_PROTO_MAX_DURATION 5000 /* msec */
4579 * enum nl80211_rxmgmt_flags - flags for received management frame.
4581 * Used by cfg80211_rx_mgmt()
4583 * @NL80211_RXMGMT_FLAG_ANSWERED: frame was answered by device/driver.
4585 enum nl80211_rxmgmt_flags {
4586 NL80211_RXMGMT_FLAG_ANSWERED = 1 << 0,
4590 * If this flag is unset, the lower 24 bits are an OUI, if set
4591 * a Linux nl80211 vendor ID is used (no such IDs are allocated
4592 * yet, so that's not valid so far)
4594 #define NL80211_VENDOR_ID_IS_LINUX 0x80000000
4597 * struct nl80211_vendor_cmd_info - vendor command data
4598 * @vendor_id: If the %NL80211_VENDOR_ID_IS_LINUX flag is clear, then the
4599 * value is a 24-bit OUI; if it is set then a separately allocated ID
4600 * may be used, but no such IDs are allocated yet. New IDs should be
4601 * added to this file when needed.
4602 * @subcmd: sub-command ID for the command
4604 struct nl80211_vendor_cmd_info {
4610 * enum nl80211_tdls_peer_capability - TDLS peer flags.
4612 * Used by tdls_mgmt() to determine which conditional elements need
4613 * to be added to TDLS Setup frames.
4615 * @NL80211_TDLS_PEER_HT: TDLS peer is HT capable.
4616 * @NL80211_TDLS_PEER_VHT: TDLS peer is VHT capable.
4617 * @NL80211_TDLS_PEER_WMM: TDLS peer is WMM capable.
4619 enum nl80211_tdls_peer_capability {
4620 NL80211_TDLS_PEER_HT = 1<<0,
4621 NL80211_TDLS_PEER_VHT = 1<<1,
4622 NL80211_TDLS_PEER_WMM = 1<<2,
4626 * enum nl80211_sched_scan_plan - scanning plan for scheduled scan
4627 * @__NL80211_SCHED_SCAN_PLAN_INVALID: attribute number 0 is reserved
4628 * @NL80211_SCHED_SCAN_PLAN_INTERVAL: interval between scan iterations. In
4630 * @NL80211_SCHED_SCAN_PLAN_ITERATIONS: number of scan iterations in this
4631 * scan plan (u32). The last scan plan must not specify this attribute
4632 * because it will run infinitely. A value of zero is invalid as it will
4633 * make the scan plan meaningless.
4634 * @NL80211_SCHED_SCAN_PLAN_MAX: highest scheduled scan plan attribute number
4636 * @__NL80211_SCHED_SCAN_PLAN_AFTER_LAST: internal use
4638 enum nl80211_sched_scan_plan {
4639 __NL80211_SCHED_SCAN_PLAN_INVALID,
4640 NL80211_SCHED_SCAN_PLAN_INTERVAL,
4641 NL80211_SCHED_SCAN_PLAN_ITERATIONS,
4644 __NL80211_SCHED_SCAN_PLAN_AFTER_LAST,
4645 NL80211_SCHED_SCAN_PLAN_MAX =
4646 __NL80211_SCHED_SCAN_PLAN_AFTER_LAST - 1
4649 #endif /* __LINUX_NL80211_H */