1 // SPDX-License-Identifier: GPL-2.0
3 * Silicon Laboratories CP210x USB to RS232 serial adaptor driver
5 * Copyright (C) 2005 Craig Shelley (craig@microtron.org.uk)
7 * Support to set flow control line levels using TIOCMGET and TIOCMSET
8 * thanks to Karl Hiramoto karl@hiramoto.org. RTSCTS hardware flow
9 * control thanks to Munir Nassar nassarmu@real-time.com
13 #include <linux/kernel.h>
14 #include <linux/errno.h>
15 #include <linux/slab.h>
16 #include <linux/tty.h>
17 #include <linux/tty_flip.h>
18 #include <linux/module.h>
19 #include <linux/moduleparam.h>
20 #include <linux/usb.h>
21 #include <linux/uaccess.h>
22 #include <linux/usb/serial.h>
23 #include <linux/gpio/driver.h>
24 #include <linux/bitops.h>
25 #include <linux/mutex.h>
27 #define DRIVER_DESC "Silicon Labs CP210x RS232 serial adaptor driver"
32 static int cp210x_open(struct tty_struct *tty, struct usb_serial_port *);
33 static void cp210x_close(struct usb_serial_port *);
34 static void cp210x_get_termios(struct tty_struct *, struct usb_serial_port *);
35 static void cp210x_get_termios_port(struct usb_serial_port *port,
36 tcflag_t *cflagp, unsigned int *baudp);
37 static void cp210x_change_speed(struct tty_struct *, struct usb_serial_port *,
39 static void cp210x_set_termios(struct tty_struct *, struct usb_serial_port *,
41 static bool cp210x_tx_empty(struct usb_serial_port *port);
42 static int cp210x_tiocmget(struct tty_struct *);
43 static int cp210x_tiocmset(struct tty_struct *, unsigned int, unsigned int);
44 static int cp210x_tiocmset_port(struct usb_serial_port *port,
45 unsigned int, unsigned int);
46 static void cp210x_break_ctl(struct tty_struct *, int);
47 static int cp210x_attach(struct usb_serial *);
48 static void cp210x_disconnect(struct usb_serial *);
49 static void cp210x_release(struct usb_serial *);
50 static int cp210x_port_probe(struct usb_serial_port *);
51 static int cp210x_port_remove(struct usb_serial_port *);
52 static void cp210x_dtr_rts(struct usb_serial_port *p, int on);
54 static const struct usb_device_id id_table[] = {
55 { USB_DEVICE(0x0404, 0x034C) }, /* NCR Retail IO Box */
56 { USB_DEVICE(0x045B, 0x0053) }, /* Renesas RX610 RX-Stick */
57 { USB_DEVICE(0x0471, 0x066A) }, /* AKTAKOM ACE-1001 cable */
58 { USB_DEVICE(0x0489, 0xE000) }, /* Pirelli Broadband S.p.A, DP-L10 SIP/GSM Mobile */
59 { USB_DEVICE(0x0489, 0xE003) }, /* Pirelli Broadband S.p.A, DP-L10 SIP/GSM Mobile */
60 { USB_DEVICE(0x0745, 0x1000) }, /* CipherLab USB CCD Barcode Scanner 1000 */
61 { USB_DEVICE(0x0846, 0x1100) }, /* NetGear Managed Switch M4100 series, M5300 series, M7100 series */
62 { USB_DEVICE(0x08e6, 0x5501) }, /* Gemalto Prox-PU/CU contactless smartcard reader */
63 { USB_DEVICE(0x08FD, 0x000A) }, /* Digianswer A/S , ZigBee/802.15.4 MAC Device */
64 { USB_DEVICE(0x0908, 0x01FF) }, /* Siemens RUGGEDCOM USB Serial Console */
65 { USB_DEVICE(0x0988, 0x0578) }, /* Teraoka AD2000 */
66 { USB_DEVICE(0x0B00, 0x3070) }, /* Ingenico 3070 */
67 { USB_DEVICE(0x0BED, 0x1100) }, /* MEI (TM) Cashflow-SC Bill/Voucher Acceptor */
68 { USB_DEVICE(0x0BED, 0x1101) }, /* MEI series 2000 Combo Acceptor */
69 { USB_DEVICE(0x0FCF, 0x1003) }, /* Dynastream ANT development board */
70 { USB_DEVICE(0x0FCF, 0x1004) }, /* Dynastream ANT2USB */
71 { USB_DEVICE(0x0FCF, 0x1006) }, /* Dynastream ANT development board */
72 { USB_DEVICE(0x0FDE, 0xCA05) }, /* OWL Wireless Electricity Monitor CM-160 */
73 { USB_DEVICE(0x106F, 0x0003) }, /* CPI / Money Controls Bulk Coin Recycler */
74 { USB_DEVICE(0x10A6, 0xAA26) }, /* Knock-off DCU-11 cable */
75 { USB_DEVICE(0x10AB, 0x10C5) }, /* Siemens MC60 Cable */
76 { USB_DEVICE(0x10B5, 0xAC70) }, /* Nokia CA-42 USB */
77 { USB_DEVICE(0x10C4, 0x0F91) }, /* Vstabi */
78 { USB_DEVICE(0x10C4, 0x1101) }, /* Arkham Technology DS101 Bus Monitor */
79 { USB_DEVICE(0x10C4, 0x1601) }, /* Arkham Technology DS101 Adapter */
80 { USB_DEVICE(0x10C4, 0x800A) }, /* SPORTident BSM7-D-USB main station */
81 { USB_DEVICE(0x10C4, 0x803B) }, /* Pololu USB-serial converter */
82 { USB_DEVICE(0x10C4, 0x8044) }, /* Cygnal Debug Adapter */
83 { USB_DEVICE(0x10C4, 0x804E) }, /* Software Bisque Paramount ME build-in converter */
84 { USB_DEVICE(0x10C4, 0x8053) }, /* Enfora EDG1228 */
85 { USB_DEVICE(0x10C4, 0x8054) }, /* Enfora GSM2228 */
86 { USB_DEVICE(0x10C4, 0x8056) }, /* Lorenz Messtechnik devices */
87 { USB_DEVICE(0x10C4, 0x8066) }, /* Argussoft In-System Programmer */
88 { USB_DEVICE(0x10C4, 0x806F) }, /* IMS USB to RS422 Converter Cable */
89 { USB_DEVICE(0x10C4, 0x807A) }, /* Crumb128 board */
90 { USB_DEVICE(0x10C4, 0x80C4) }, /* Cygnal Integrated Products, Inc., Optris infrared thermometer */
91 { USB_DEVICE(0x10C4, 0x80CA) }, /* Degree Controls Inc */
92 { USB_DEVICE(0x10C4, 0x80DD) }, /* Tracient RFID */
93 { USB_DEVICE(0x10C4, 0x80F6) }, /* Suunto sports instrument */
94 { USB_DEVICE(0x10C4, 0x8115) }, /* Arygon NFC/Mifare Reader */
95 { USB_DEVICE(0x10C4, 0x813D) }, /* Burnside Telecom Deskmobile */
96 { USB_DEVICE(0x10C4, 0x813F) }, /* Tams Master Easy Control */
97 { USB_DEVICE(0x10C4, 0x814A) }, /* West Mountain Radio RIGblaster P&P */
98 { USB_DEVICE(0x10C4, 0x814B) }, /* West Mountain Radio RIGtalk */
99 { USB_DEVICE(0x2405, 0x0003) }, /* West Mountain Radio RIGblaster Advantage */
100 { USB_DEVICE(0x10C4, 0x8156) }, /* B&G H3000 link cable */
101 { USB_DEVICE(0x10C4, 0x815E) }, /* Helicomm IP-Link 1220-DVM */
102 { USB_DEVICE(0x10C4, 0x815F) }, /* Timewave HamLinkUSB */
103 { USB_DEVICE(0x10C4, 0x817C) }, /* CESINEL MEDCAL N Power Quality Monitor */
104 { USB_DEVICE(0x10C4, 0x817D) }, /* CESINEL MEDCAL NT Power Quality Monitor */
105 { USB_DEVICE(0x10C4, 0x817E) }, /* CESINEL MEDCAL S Power Quality Monitor */
106 { USB_DEVICE(0x10C4, 0x818B) }, /* AVIT Research USB to TTL */
107 { USB_DEVICE(0x10C4, 0x819F) }, /* MJS USB Toslink Switcher */
108 { USB_DEVICE(0x10C4, 0x81A6) }, /* ThinkOptics WavIt */
109 { USB_DEVICE(0x10C4, 0x81A9) }, /* Multiplex RC Interface */
110 { USB_DEVICE(0x10C4, 0x81AC) }, /* MSD Dash Hawk */
111 { USB_DEVICE(0x10C4, 0x81AD) }, /* INSYS USB Modem */
112 { USB_DEVICE(0x10C4, 0x81C8) }, /* Lipowsky Industrie Elektronik GmbH, Baby-JTAG */
113 { USB_DEVICE(0x10C4, 0x81D7) }, /* IAI Corp. RCB-CV-USB USB to RS485 Adaptor */
114 { USB_DEVICE(0x10C4, 0x81E2) }, /* Lipowsky Industrie Elektronik GmbH, Baby-LIN */
115 { USB_DEVICE(0x10C4, 0x81E7) }, /* Aerocomm Radio */
116 { USB_DEVICE(0x10C4, 0x81E8) }, /* Zephyr Bioharness */
117 { USB_DEVICE(0x10C4, 0x81F2) }, /* C1007 HF band RFID controller */
118 { USB_DEVICE(0x10C4, 0x8218) }, /* Lipowsky Industrie Elektronik GmbH, HARP-1 */
119 { USB_DEVICE(0x10C4, 0x822B) }, /* Modem EDGE(GSM) Comander 2 */
120 { USB_DEVICE(0x10C4, 0x826B) }, /* Cygnal Integrated Products, Inc., Fasttrax GPS demonstration module */
121 { USB_DEVICE(0x10C4, 0x8281) }, /* Nanotec Plug & Drive */
122 { USB_DEVICE(0x10C4, 0x8293) }, /* Telegesis ETRX2USB */
123 { USB_DEVICE(0x10C4, 0x82EF) }, /* CESINEL FALCO 6105 AC Power Supply */
124 { USB_DEVICE(0x10C4, 0x82F1) }, /* CESINEL MEDCAL EFD Earth Fault Detector */
125 { USB_DEVICE(0x10C4, 0x82F2) }, /* CESINEL MEDCAL ST Network Analyzer */
126 { USB_DEVICE(0x10C4, 0x82F4) }, /* Starizona MicroTouch */
127 { USB_DEVICE(0x10C4, 0x82F9) }, /* Procyon AVS */
128 { USB_DEVICE(0x10C4, 0x8341) }, /* Siemens MC35PU GPRS Modem */
129 { USB_DEVICE(0x10C4, 0x8382) }, /* Cygnal Integrated Products, Inc. */
130 { USB_DEVICE(0x10C4, 0x83A8) }, /* Amber Wireless AMB2560 */
131 { USB_DEVICE(0x10C4, 0x83AA) }, /* Mark-10 Digital Force Gauge */
132 { USB_DEVICE(0x10C4, 0x83D8) }, /* DekTec DTA Plus VHF/UHF Booster/Attenuator */
133 { USB_DEVICE(0x10C4, 0x8411) }, /* Kyocera GPS Module */
134 { USB_DEVICE(0x10C4, 0x8414) }, /* Decagon USB Cable Adapter */
135 { USB_DEVICE(0x10C4, 0x8418) }, /* IRZ Automation Teleport SG-10 GSM/GPRS Modem */
136 { USB_DEVICE(0x10C4, 0x846E) }, /* BEI USB Sensor Interface (VCP) */
137 { USB_DEVICE(0x10C4, 0x8470) }, /* Juniper Networks BX Series System Console */
138 { USB_DEVICE(0x10C4, 0x8477) }, /* Balluff RFID */
139 { USB_DEVICE(0x10C4, 0x84B6) }, /* Starizona Hyperion */
140 { USB_DEVICE(0x10C4, 0x851E) }, /* CESINEL MEDCAL PT Network Analyzer */
141 { USB_DEVICE(0x10C4, 0x85A7) }, /* LifeScan OneTouch Verio IQ */
142 { USB_DEVICE(0x10C4, 0x85B8) }, /* CESINEL ReCon T Energy Logger */
143 { USB_DEVICE(0x10C4, 0x85EA) }, /* AC-Services IBUS-IF */
144 { USB_DEVICE(0x10C4, 0x85EB) }, /* AC-Services CIS-IBUS */
145 { USB_DEVICE(0x10C4, 0x85F8) }, /* Virtenio Preon32 */
146 { USB_DEVICE(0x10C4, 0x8664) }, /* AC-Services CAN-IF */
147 { USB_DEVICE(0x10C4, 0x8665) }, /* AC-Services OBD-IF */
148 { USB_DEVICE(0x10C4, 0x8856) }, /* CEL EM357 ZigBee USB Stick - LR */
149 { USB_DEVICE(0x10C4, 0x8857) }, /* CEL EM357 ZigBee USB Stick */
150 { USB_DEVICE(0x10C4, 0x88A4) }, /* MMB Networks ZigBee USB Device */
151 { USB_DEVICE(0x10C4, 0x88A5) }, /* Planet Innovation Ingeni ZigBee USB Device */
152 { USB_DEVICE(0x10C4, 0x88D8) }, /* Acuity Brands nLight Air Adapter */
153 { USB_DEVICE(0x10C4, 0x88FB) }, /* CESINEL MEDCAL STII Network Analyzer */
154 { USB_DEVICE(0x10C4, 0x8938) }, /* CESINEL MEDCAL S II Network Analyzer */
155 { USB_DEVICE(0x10C4, 0x8946) }, /* Ketra N1 Wireless Interface */
156 { USB_DEVICE(0x10C4, 0x8962) }, /* Brim Brothers charging dock */
157 { USB_DEVICE(0x10C4, 0x8977) }, /* CEL MeshWorks DevKit Device */
158 { USB_DEVICE(0x10C4, 0x8998) }, /* KCF Technologies PRN */
159 { USB_DEVICE(0x10C4, 0x89A4) }, /* CESINEL FTBC Flexible Thyristor Bridge Controller */
160 { USB_DEVICE(0x10C4, 0x89FB) }, /* Qivicon ZigBee USB Radio Stick */
161 { USB_DEVICE(0x10C4, 0x8A2A) }, /* HubZ dual ZigBee and Z-Wave dongle */
162 { USB_DEVICE(0x10C4, 0x8A5B) }, /* CEL EM3588 ZigBee USB Stick */
163 { USB_DEVICE(0x10C4, 0x8A5E) }, /* CEL EM3588 ZigBee USB Stick Long Range */
164 { USB_DEVICE(0x10C4, 0x8B34) }, /* Qivicon ZigBee USB Radio Stick */
165 { USB_DEVICE(0x10C4, 0xEA60) }, /* Silicon Labs factory default */
166 { USB_DEVICE(0x10C4, 0xEA61) }, /* Silicon Labs factory default */
167 { USB_DEVICE(0x10C4, 0xEA63) }, /* Silicon Labs Windows Update (CP2101-4/CP2102N) */
168 { USB_DEVICE(0x10C4, 0xEA70) }, /* Silicon Labs factory default */
169 { USB_DEVICE(0x10C4, 0xEA71) }, /* Infinity GPS-MIC-1 Radio Monophone */
170 { USB_DEVICE(0x10C4, 0xEA7A) }, /* Silicon Labs Windows Update (CP2105) */
171 { USB_DEVICE(0x10C4, 0xEA7B) }, /* Silicon Labs Windows Update (CP2108) */
172 { USB_DEVICE(0x10C4, 0xF001) }, /* Elan Digital Systems USBscope50 */
173 { USB_DEVICE(0x10C4, 0xF002) }, /* Elan Digital Systems USBwave12 */
174 { USB_DEVICE(0x10C4, 0xF003) }, /* Elan Digital Systems USBpulse100 */
175 { USB_DEVICE(0x10C4, 0xF004) }, /* Elan Digital Systems USBcount50 */
176 { USB_DEVICE(0x10C5, 0xEA61) }, /* Silicon Labs MobiData GPRS USB Modem */
177 { USB_DEVICE(0x10CE, 0xEA6A) }, /* Silicon Labs MobiData GPRS USB Modem 100EU */
178 { USB_DEVICE(0x12B8, 0xEC60) }, /* Link G4 ECU */
179 { USB_DEVICE(0x12B8, 0xEC62) }, /* Link G4+ ECU */
180 { USB_DEVICE(0x13AD, 0x9999) }, /* Baltech card reader */
181 { USB_DEVICE(0x1555, 0x0004) }, /* Owen AC4 USB-RS485 Converter */
182 { USB_DEVICE(0x155A, 0x1006) }, /* ELDAT Easywave RX09 */
183 { USB_DEVICE(0x166A, 0x0201) }, /* Clipsal 5500PACA C-Bus Pascal Automation Controller */
184 { USB_DEVICE(0x166A, 0x0301) }, /* Clipsal 5800PC C-Bus Wireless PC Interface */
185 { USB_DEVICE(0x166A, 0x0303) }, /* Clipsal 5500PCU C-Bus USB interface */
186 { USB_DEVICE(0x166A, 0x0304) }, /* Clipsal 5000CT2 C-Bus Black and White Touchscreen */
187 { USB_DEVICE(0x166A, 0x0305) }, /* Clipsal C-5000CT2 C-Bus Spectrum Colour Touchscreen */
188 { USB_DEVICE(0x166A, 0x0401) }, /* Clipsal L51xx C-Bus Architectural Dimmer */
189 { USB_DEVICE(0x166A, 0x0101) }, /* Clipsal 5560884 C-Bus Multi-room Audio Matrix Switcher */
190 { USB_DEVICE(0x16C0, 0x09B0) }, /* Lunatico Seletek */
191 { USB_DEVICE(0x16C0, 0x09B1) }, /* Lunatico Seletek */
192 { USB_DEVICE(0x16D6, 0x0001) }, /* Jablotron serial interface */
193 { USB_DEVICE(0x16DC, 0x0010) }, /* W-IE-NE-R Plein & Baus GmbH PL512 Power Supply */
194 { USB_DEVICE(0x16DC, 0x0011) }, /* W-IE-NE-R Plein & Baus GmbH RCM Remote Control for MARATON Power Supply */
195 { USB_DEVICE(0x16DC, 0x0012) }, /* W-IE-NE-R Plein & Baus GmbH MPOD Multi Channel Power Supply */
196 { USB_DEVICE(0x16DC, 0x0015) }, /* W-IE-NE-R Plein & Baus GmbH CML Control, Monitoring and Data Logger */
197 { USB_DEVICE(0x17A8, 0x0001) }, /* Kamstrup Optical Eye/3-wire */
198 { USB_DEVICE(0x17A8, 0x0005) }, /* Kamstrup M-Bus Master MultiPort 250D */
199 { USB_DEVICE(0x17A8, 0x0101) }, /* Kamstrup 868 MHz wM-Bus C-Mode Meter Reader (Int Ant) */
200 { USB_DEVICE(0x17A8, 0x0102) }, /* Kamstrup 868 MHz wM-Bus C-Mode Meter Reader (Ext Ant) */
201 { USB_DEVICE(0x17F4, 0xAAAA) }, /* Wavesense Jazz blood glucose meter */
202 { USB_DEVICE(0x1843, 0x0200) }, /* Vaisala USB Instrument Cable */
203 { USB_DEVICE(0x18EF, 0xE00F) }, /* ELV USB-I2C-Interface */
204 { USB_DEVICE(0x18EF, 0xE025) }, /* ELV Marble Sound Board 1 */
205 { USB_DEVICE(0x18EF, 0xE030) }, /* ELV ALC 8xxx Battery Charger */
206 { USB_DEVICE(0x18EF, 0xE032) }, /* ELV TFD500 Data Logger */
207 { USB_DEVICE(0x1901, 0x0190) }, /* GE B850 CP2105 Recorder interface */
208 { USB_DEVICE(0x1901, 0x0193) }, /* GE B650 CP2104 PMC interface */
209 { USB_DEVICE(0x1901, 0x0194) }, /* GE Healthcare Remote Alarm Box */
210 { USB_DEVICE(0x1901, 0x0195) }, /* GE B850/B650/B450 CP2104 DP UART interface */
211 { USB_DEVICE(0x1901, 0x0196) }, /* GE B850 CP2105 DP UART interface */
212 { USB_DEVICE(0x1901, 0x0197) }, /* GE CS1000 M.2 Key E serial interface */
213 { USB_DEVICE(0x1901, 0x0198) }, /* GE CS1000 Display serial interface */
214 { USB_DEVICE(0x199B, 0xBA30) }, /* LORD WSDA-200-USB */
215 { USB_DEVICE(0x19CF, 0x3000) }, /* Parrot NMEA GPS Flight Recorder */
216 { USB_DEVICE(0x1ADB, 0x0001) }, /* Schweitzer Engineering C662 Cable */
217 { USB_DEVICE(0x1B1C, 0x1C00) }, /* Corsair USB Dongle */
218 { USB_DEVICE(0x1BA4, 0x0002) }, /* Silicon Labs 358x factory default */
219 { USB_DEVICE(0x1BE3, 0x07A6) }, /* WAGO 750-923 USB Service Cable */
220 { USB_DEVICE(0x1D6F, 0x0010) }, /* Seluxit ApS RF Dongle */
221 { USB_DEVICE(0x1E29, 0x0102) }, /* Festo CPX-USB */
222 { USB_DEVICE(0x1E29, 0x0501) }, /* Festo CMSP */
223 { USB_DEVICE(0x1FB9, 0x0100) }, /* Lake Shore Model 121 Current Source */
224 { USB_DEVICE(0x1FB9, 0x0200) }, /* Lake Shore Model 218A Temperature Monitor */
225 { USB_DEVICE(0x1FB9, 0x0201) }, /* Lake Shore Model 219 Temperature Monitor */
226 { USB_DEVICE(0x1FB9, 0x0202) }, /* Lake Shore Model 233 Temperature Transmitter */
227 { USB_DEVICE(0x1FB9, 0x0203) }, /* Lake Shore Model 235 Temperature Transmitter */
228 { USB_DEVICE(0x1FB9, 0x0300) }, /* Lake Shore Model 335 Temperature Controller */
229 { USB_DEVICE(0x1FB9, 0x0301) }, /* Lake Shore Model 336 Temperature Controller */
230 { USB_DEVICE(0x1FB9, 0x0302) }, /* Lake Shore Model 350 Temperature Controller */
231 { USB_DEVICE(0x1FB9, 0x0303) }, /* Lake Shore Model 371 AC Bridge */
232 { USB_DEVICE(0x1FB9, 0x0400) }, /* Lake Shore Model 411 Handheld Gaussmeter */
233 { USB_DEVICE(0x1FB9, 0x0401) }, /* Lake Shore Model 425 Gaussmeter */
234 { USB_DEVICE(0x1FB9, 0x0402) }, /* Lake Shore Model 455A Gaussmeter */
235 { USB_DEVICE(0x1FB9, 0x0403) }, /* Lake Shore Model 475A Gaussmeter */
236 { USB_DEVICE(0x1FB9, 0x0404) }, /* Lake Shore Model 465 Three Axis Gaussmeter */
237 { USB_DEVICE(0x1FB9, 0x0600) }, /* Lake Shore Model 625A Superconducting MPS */
238 { USB_DEVICE(0x1FB9, 0x0601) }, /* Lake Shore Model 642A Magnet Power Supply */
239 { USB_DEVICE(0x1FB9, 0x0602) }, /* Lake Shore Model 648 Magnet Power Supply */
240 { USB_DEVICE(0x1FB9, 0x0700) }, /* Lake Shore Model 737 VSM Controller */
241 { USB_DEVICE(0x1FB9, 0x0701) }, /* Lake Shore Model 776 Hall Matrix */
242 { USB_DEVICE(0x2184, 0x0030) }, /* GW Instek GDM-834x Digital Multimeter */
243 { USB_DEVICE(0x2626, 0xEA60) }, /* Aruba Networks 7xxx USB Serial Console */
244 { USB_DEVICE(0x3195, 0xF190) }, /* Link Instruments MSO-19 */
245 { USB_DEVICE(0x3195, 0xF280) }, /* Link Instruments MSO-28 */
246 { USB_DEVICE(0x3195, 0xF281) }, /* Link Instruments MSO-28 */
247 { USB_DEVICE(0x3923, 0x7A0B) }, /* National Instruments USB Serial Console */
248 { USB_DEVICE(0x413C, 0x9500) }, /* DW700 GPS USB interface */
249 { } /* Terminating Entry */
252 MODULE_DEVICE_TABLE(usb, id_table);
254 struct cp210x_serial_private {
255 #ifdef CONFIG_GPIOLIB
257 bool gpio_registered;
264 bool use_actual_rate;
267 struct cp210x_port_private {
268 __u8 bInterfaceNumber;
269 bool has_swapped_line_ctl;
272 static struct usb_serial_driver cp210x_device = {
274 .owner = THIS_MODULE,
277 .id_table = id_table,
280 .bulk_out_size = 256,
282 .close = cp210x_close,
283 .break_ctl = cp210x_break_ctl,
284 .set_termios = cp210x_set_termios,
285 .tx_empty = cp210x_tx_empty,
286 .throttle = usb_serial_generic_throttle,
287 .unthrottle = usb_serial_generic_unthrottle,
288 .tiocmget = cp210x_tiocmget,
289 .tiocmset = cp210x_tiocmset,
290 .attach = cp210x_attach,
291 .disconnect = cp210x_disconnect,
292 .release = cp210x_release,
293 .port_probe = cp210x_port_probe,
294 .port_remove = cp210x_port_remove,
295 .dtr_rts = cp210x_dtr_rts
298 static struct usb_serial_driver * const serial_drivers[] = {
302 /* Config request types */
303 #define REQTYPE_HOST_TO_INTERFACE 0x41
304 #define REQTYPE_INTERFACE_TO_HOST 0xc1
305 #define REQTYPE_HOST_TO_DEVICE 0x40
306 #define REQTYPE_DEVICE_TO_HOST 0xc0
308 /* Config request codes */
309 #define CP210X_IFC_ENABLE 0x00
310 #define CP210X_SET_BAUDDIV 0x01
311 #define CP210X_GET_BAUDDIV 0x02
312 #define CP210X_SET_LINE_CTL 0x03
313 #define CP210X_GET_LINE_CTL 0x04
314 #define CP210X_SET_BREAK 0x05
315 #define CP210X_IMM_CHAR 0x06
316 #define CP210X_SET_MHS 0x07
317 #define CP210X_GET_MDMSTS 0x08
318 #define CP210X_SET_XON 0x09
319 #define CP210X_SET_XOFF 0x0A
320 #define CP210X_SET_EVENTMASK 0x0B
321 #define CP210X_GET_EVENTMASK 0x0C
322 #define CP210X_SET_CHAR 0x0D
323 #define CP210X_GET_CHARS 0x0E
324 #define CP210X_GET_PROPS 0x0F
325 #define CP210X_GET_COMM_STATUS 0x10
326 #define CP210X_RESET 0x11
327 #define CP210X_PURGE 0x12
328 #define CP210X_SET_FLOW 0x13
329 #define CP210X_GET_FLOW 0x14
330 #define CP210X_EMBED_EVENTS 0x15
331 #define CP210X_GET_EVENTSTATE 0x16
332 #define CP210X_SET_CHARS 0x19
333 #define CP210X_GET_BAUDRATE 0x1D
334 #define CP210X_SET_BAUDRATE 0x1E
335 #define CP210X_VENDOR_SPECIFIC 0xFF
337 /* CP210X_IFC_ENABLE */
338 #define UART_ENABLE 0x0001
339 #define UART_DISABLE 0x0000
341 /* CP210X_(SET|GET)_BAUDDIV */
342 #define BAUD_RATE_GEN_FREQ 0x384000
344 /* CP210X_(SET|GET)_LINE_CTL */
345 #define BITS_DATA_MASK 0X0f00
346 #define BITS_DATA_5 0X0500
347 #define BITS_DATA_6 0X0600
348 #define BITS_DATA_7 0X0700
349 #define BITS_DATA_8 0X0800
350 #define BITS_DATA_9 0X0900
352 #define BITS_PARITY_MASK 0x00f0
353 #define BITS_PARITY_NONE 0x0000
354 #define BITS_PARITY_ODD 0x0010
355 #define BITS_PARITY_EVEN 0x0020
356 #define BITS_PARITY_MARK 0x0030
357 #define BITS_PARITY_SPACE 0x0040
359 #define BITS_STOP_MASK 0x000f
360 #define BITS_STOP_1 0x0000
361 #define BITS_STOP_1_5 0x0001
362 #define BITS_STOP_2 0x0002
364 /* CP210X_SET_BREAK */
365 #define BREAK_ON 0x0001
366 #define BREAK_OFF 0x0000
368 /* CP210X_(SET_MHS|GET_MDMSTS) */
369 #define CONTROL_DTR 0x0001
370 #define CONTROL_RTS 0x0002
371 #define CONTROL_CTS 0x0010
372 #define CONTROL_DSR 0x0020
373 #define CONTROL_RING 0x0040
374 #define CONTROL_DCD 0x0080
375 #define CONTROL_WRITE_DTR 0x0100
376 #define CONTROL_WRITE_RTS 0x0200
378 /* CP210X_VENDOR_SPECIFIC values */
379 #define CP210X_READ_2NCONFIG 0x000E
380 #define CP210X_READ_LATCH 0x00C2
381 #define CP210X_GET_PARTNUM 0x370B
382 #define CP210X_GET_PORTCONFIG 0x370C
383 #define CP210X_GET_DEVICEMODE 0x3711
384 #define CP210X_WRITE_LATCH 0x37E1
386 /* Part number definitions */
387 #define CP210X_PARTNUM_CP2101 0x01
388 #define CP210X_PARTNUM_CP2102 0x02
389 #define CP210X_PARTNUM_CP2103 0x03
390 #define CP210X_PARTNUM_CP2104 0x04
391 #define CP210X_PARTNUM_CP2105 0x05
392 #define CP210X_PARTNUM_CP2108 0x08
393 #define CP210X_PARTNUM_CP2102N_QFN28 0x20
394 #define CP210X_PARTNUM_CP2102N_QFN24 0x21
395 #define CP210X_PARTNUM_CP2102N_QFN20 0x22
396 #define CP210X_PARTNUM_UNKNOWN 0xFF
398 /* CP210X_GET_COMM_STATUS returns these 0x13 bytes */
399 struct cp210x_comm_status {
401 __le32 ulHoldReasons;
402 __le32 ulAmountInInQueue;
403 __le32 ulAmountInOutQueue;
405 u8 bWaitForImmediate;
410 * CP210X_PURGE - 16 bits passed in wValue of USB request.
411 * SiLabs app note AN571 gives a strange description of the 4 bits:
412 * bit 0 or bit 2 clears the transmit queue and 1 or 3 receive.
413 * writing 1 to all, however, purges cp2108 well enough to avoid the hang.
415 #define PURGE_ALL 0x000f
417 /* CP210X_GET_FLOW/CP210X_SET_FLOW read/write these 0x10 bytes */
418 struct cp210x_flow_ctl {
419 __le32 ulControlHandshake;
420 __le32 ulFlowReplace;
425 /* cp210x_flow_ctl::ulControlHandshake */
426 #define CP210X_SERIAL_DTR_MASK GENMASK(1, 0)
427 #define CP210X_SERIAL_DTR_SHIFT(_mode) (_mode)
428 #define CP210X_SERIAL_CTS_HANDSHAKE BIT(3)
429 #define CP210X_SERIAL_DSR_HANDSHAKE BIT(4)
430 #define CP210X_SERIAL_DCD_HANDSHAKE BIT(5)
431 #define CP210X_SERIAL_DSR_SENSITIVITY BIT(6)
433 /* values for cp210x_flow_ctl::ulControlHandshake::CP210X_SERIAL_DTR_MASK */
434 #define CP210X_SERIAL_DTR_INACTIVE 0
435 #define CP210X_SERIAL_DTR_ACTIVE 1
436 #define CP210X_SERIAL_DTR_FLOW_CTL 2
438 /* cp210x_flow_ctl::ulFlowReplace */
439 #define CP210X_SERIAL_AUTO_TRANSMIT BIT(0)
440 #define CP210X_SERIAL_AUTO_RECEIVE BIT(1)
441 #define CP210X_SERIAL_ERROR_CHAR BIT(2)
442 #define CP210X_SERIAL_NULL_STRIPPING BIT(3)
443 #define CP210X_SERIAL_BREAK_CHAR BIT(4)
444 #define CP210X_SERIAL_RTS_MASK GENMASK(7, 6)
445 #define CP210X_SERIAL_RTS_SHIFT(_mode) (_mode << 6)
446 #define CP210X_SERIAL_XOFF_CONTINUE BIT(31)
448 /* values for cp210x_flow_ctl::ulFlowReplace::CP210X_SERIAL_RTS_MASK */
449 #define CP210X_SERIAL_RTS_INACTIVE 0
450 #define CP210X_SERIAL_RTS_ACTIVE 1
451 #define CP210X_SERIAL_RTS_FLOW_CTL 2
453 /* CP210X_VENDOR_SPECIFIC, CP210X_GET_DEVICEMODE call reads these 0x2 bytes. */
454 struct cp210x_pin_mode {
459 #define CP210X_PIN_MODE_MODEM 0
460 #define CP210X_PIN_MODE_GPIO BIT(0)
463 * CP210X_VENDOR_SPECIFIC, CP210X_GET_PORTCONFIG call reads these 0xf bytes.
464 * Structure needs padding due to unused/unspecified bytes.
466 struct cp210x_config {
471 __le16 suspend_state;
478 #define CP210X_SCI_GPIO_MODE_OFFSET 9
479 #define CP210X_SCI_GPIO_MODE_MASK GENMASK(11, 9)
481 #define CP210X_ECI_GPIO_MODE_OFFSET 2
482 #define CP210X_ECI_GPIO_MODE_MASK GENMASK(3, 2)
484 /* CP2105 port configuration values */
485 #define CP2105_GPIO0_TXLED_MODE BIT(0)
486 #define CP2105_GPIO1_RXLED_MODE BIT(1)
487 #define CP2105_GPIO1_RS485_MODE BIT(2)
489 /* CP2102N configuration array indices */
490 #define CP210X_2NCONFIG_CONFIG_VERSION_IDX 2
491 #define CP210X_2NCONFIG_GPIO_MODE_IDX 581
492 #define CP210X_2NCONFIG_GPIO_RSTLATCH_IDX 587
493 #define CP210X_2NCONFIG_GPIO_CONTROL_IDX 600
495 /* CP2102N QFN20 port configuration values */
496 #define CP2102N_QFN20_GPIO2_TXLED_MODE BIT(2)
497 #define CP2102N_QFN20_GPIO3_RXLED_MODE BIT(3)
498 #define CP2102N_QFN20_GPIO1_RS485_MODE BIT(4)
499 #define CP2102N_QFN20_GPIO0_CLK_MODE BIT(6)
501 /* CP210X_VENDOR_SPECIFIC, CP210X_WRITE_LATCH call writes these 0x2 bytes. */
502 struct cp210x_gpio_write {
508 * Helper to get interface number when we only have struct usb_serial.
510 static u8 cp210x_interface_num(struct usb_serial *serial)
512 struct usb_host_interface *cur_altsetting;
514 cur_altsetting = serial->interface->cur_altsetting;
516 return cur_altsetting->desc.bInterfaceNumber;
520 * Reads a variable-sized block of CP210X_ registers, identified by req.
521 * Returns data into buf in native USB byte order.
523 static int cp210x_read_reg_block(struct usb_serial_port *port, u8 req,
524 void *buf, int bufsize)
526 struct usb_serial *serial = port->serial;
527 struct cp210x_port_private *port_priv = usb_get_serial_port_data(port);
531 dmabuf = kmalloc(bufsize, GFP_KERNEL);
534 * FIXME Some callers don't bother to check for error,
535 * at least give them consistent junk until they are fixed
537 memset(buf, 0, bufsize);
541 result = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
542 req, REQTYPE_INTERFACE_TO_HOST, 0,
543 port_priv->bInterfaceNumber, dmabuf, bufsize,
544 USB_CTRL_SET_TIMEOUT);
545 if (result == bufsize) {
546 memcpy(buf, dmabuf, bufsize);
549 dev_err(&port->dev, "failed get req 0x%x size %d status: %d\n",
550 req, bufsize, result);
555 * FIXME Some callers don't bother to check for error,
556 * at least give them consistent junk until they are fixed
558 memset(buf, 0, bufsize);
567 * Reads any 32-bit CP210X_ register identified by req.
569 static int cp210x_read_u32_reg(struct usb_serial_port *port, u8 req, u32 *val)
574 err = cp210x_read_reg_block(port, req, &le32_val, sizeof(le32_val));
577 * FIXME Some callers don't bother to check for error,
578 * at least give them consistent junk until they are fixed
584 *val = le32_to_cpu(le32_val);
590 * Reads any 16-bit CP210X_ register identified by req.
592 static int cp210x_read_u16_reg(struct usb_serial_port *port, u8 req, u16 *val)
597 err = cp210x_read_reg_block(port, req, &le16_val, sizeof(le16_val));
601 *val = le16_to_cpu(le16_val);
607 * Reads any 8-bit CP210X_ register identified by req.
609 static int cp210x_read_u8_reg(struct usb_serial_port *port, u8 req, u8 *val)
611 return cp210x_read_reg_block(port, req, val, sizeof(*val));
615 * Reads a variable-sized vendor block of CP210X_ registers, identified by val.
616 * Returns data into buf in native USB byte order.
618 static int cp210x_read_vendor_block(struct usb_serial *serial, u8 type, u16 val,
619 void *buf, int bufsize)
624 dmabuf = kmalloc(bufsize, GFP_KERNEL);
628 result = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
629 CP210X_VENDOR_SPECIFIC, type, val,
630 cp210x_interface_num(serial), dmabuf, bufsize,
631 USB_CTRL_GET_TIMEOUT);
632 if (result == bufsize) {
633 memcpy(buf, dmabuf, bufsize);
636 dev_err(&serial->interface->dev,
637 "failed to get vendor val 0x%04x size %d: %d\n", val,
649 * Writes any 16-bit CP210X_ register (req) whose value is passed
650 * entirely in the wValue field of the USB request.
652 static int cp210x_write_u16_reg(struct usb_serial_port *port, u8 req, u16 val)
654 struct usb_serial *serial = port->serial;
655 struct cp210x_port_private *port_priv = usb_get_serial_port_data(port);
658 result = usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0),
659 req, REQTYPE_HOST_TO_INTERFACE, val,
660 port_priv->bInterfaceNumber, NULL, 0,
661 USB_CTRL_SET_TIMEOUT);
663 dev_err(&port->dev, "failed set request 0x%x status: %d\n",
671 * Writes a variable-sized block of CP210X_ registers, identified by req.
672 * Data in buf must be in native USB byte order.
674 static int cp210x_write_reg_block(struct usb_serial_port *port, u8 req,
675 void *buf, int bufsize)
677 struct usb_serial *serial = port->serial;
678 struct cp210x_port_private *port_priv = usb_get_serial_port_data(port);
682 dmabuf = kmemdup(buf, bufsize, GFP_KERNEL);
686 result = usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0),
687 req, REQTYPE_HOST_TO_INTERFACE, 0,
688 port_priv->bInterfaceNumber, dmabuf, bufsize,
689 USB_CTRL_SET_TIMEOUT);
693 if (result == bufsize) {
696 dev_err(&port->dev, "failed set req 0x%x size %d status: %d\n",
697 req, bufsize, result);
706 * Writes any 32-bit CP210X_ register identified by req.
708 static int cp210x_write_u32_reg(struct usb_serial_port *port, u8 req, u32 val)
712 le32_val = cpu_to_le32(val);
714 return cp210x_write_reg_block(port, req, &le32_val, sizeof(le32_val));
717 #ifdef CONFIG_GPIOLIB
719 * Writes a variable-sized vendor block of CP210X_ registers, identified by val.
720 * Data in buf must be in native USB byte order.
722 static int cp210x_write_vendor_block(struct usb_serial *serial, u8 type,
723 u16 val, void *buf, int bufsize)
728 dmabuf = kmemdup(buf, bufsize, GFP_KERNEL);
732 result = usb_control_msg(serial->dev, usb_sndctrlpipe(serial->dev, 0),
733 CP210X_VENDOR_SPECIFIC, type, val,
734 cp210x_interface_num(serial), dmabuf, bufsize,
735 USB_CTRL_SET_TIMEOUT);
739 if (result == bufsize) {
742 dev_err(&serial->interface->dev,
743 "failed to set vendor val 0x%04x size %d: %d\n", val,
754 * Detect CP2108 GET_LINE_CTL bug and activate workaround.
755 * Write a known good value 0x800, read it back.
756 * If it comes back swapped the bug is detected.
757 * Preserve the original register value.
759 static int cp210x_detect_swapped_line_ctl(struct usb_serial_port *port)
761 struct cp210x_port_private *port_priv = usb_get_serial_port_data(port);
766 err = cp210x_read_u16_reg(port, CP210X_GET_LINE_CTL, &line_ctl_save);
770 err = cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, 0x800);
774 err = cp210x_read_u16_reg(port, CP210X_GET_LINE_CTL, &line_ctl_test);
778 if (line_ctl_test == 8) {
779 port_priv->has_swapped_line_ctl = true;
780 line_ctl_save = swab16(line_ctl_save);
783 return cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, line_ctl_save);
787 * Must always be called instead of cp210x_read_u16_reg(CP210X_GET_LINE_CTL)
788 * to workaround cp2108 bug and get correct value.
790 static int cp210x_get_line_ctl(struct usb_serial_port *port, u16 *ctl)
792 struct cp210x_port_private *port_priv = usb_get_serial_port_data(port);
795 err = cp210x_read_u16_reg(port, CP210X_GET_LINE_CTL, ctl);
799 /* Workaround swapped bytes in 16-bit value from CP210X_GET_LINE_CTL */
800 if (port_priv->has_swapped_line_ctl)
806 static int cp210x_open(struct tty_struct *tty, struct usb_serial_port *port)
810 result = cp210x_write_u16_reg(port, CP210X_IFC_ENABLE, UART_ENABLE);
812 dev_err(&port->dev, "%s - Unable to enable UART\n", __func__);
816 /* Configure the termios structure */
817 cp210x_get_termios(tty, port);
819 /* The baud rate must be initialised on cp2104 */
821 cp210x_change_speed(tty, port, NULL);
823 return usb_serial_generic_open(tty, port);
826 static void cp210x_close(struct usb_serial_port *port)
828 usb_serial_generic_close(port);
830 /* Clear both queues; cp2108 needs this to avoid an occasional hang */
831 cp210x_write_u16_reg(port, CP210X_PURGE, PURGE_ALL);
833 cp210x_write_u16_reg(port, CP210X_IFC_ENABLE, UART_DISABLE);
837 * Read how many bytes are waiting in the TX queue.
839 static int cp210x_get_tx_queue_byte_count(struct usb_serial_port *port,
842 struct usb_serial *serial = port->serial;
843 struct cp210x_port_private *port_priv = usb_get_serial_port_data(port);
844 struct cp210x_comm_status *sts;
847 sts = kmalloc(sizeof(*sts), GFP_KERNEL);
851 result = usb_control_msg(serial->dev, usb_rcvctrlpipe(serial->dev, 0),
852 CP210X_GET_COMM_STATUS, REQTYPE_INTERFACE_TO_HOST,
853 0, port_priv->bInterfaceNumber, sts, sizeof(*sts),
854 USB_CTRL_GET_TIMEOUT);
855 if (result == sizeof(*sts)) {
856 *count = le32_to_cpu(sts->ulAmountInOutQueue);
859 dev_err(&port->dev, "failed to get comm status: %d\n", result);
869 static bool cp210x_tx_empty(struct usb_serial_port *port)
874 err = cp210x_get_tx_queue_byte_count(port, &count);
883 * Reads the baud rate, data bits, parity, stop bits and flow control mode
884 * from the device, corrects any unsupported values, and configures the
885 * termios structure to reflect the state of the device
887 static void cp210x_get_termios(struct tty_struct *tty,
888 struct usb_serial_port *port)
893 cp210x_get_termios_port(tty->driver_data,
894 &tty->termios.c_cflag, &baud);
895 tty_encode_baud_rate(tty, baud, baud);
899 cp210x_get_termios_port(port, &cflag, &baud);
904 * cp210x_get_termios_port
905 * This is the heart of cp210x_get_termios which always uses a &usb_serial_port.
907 static void cp210x_get_termios_port(struct usb_serial_port *port,
908 tcflag_t *cflagp, unsigned int *baudp)
910 struct device *dev = &port->dev;
912 struct cp210x_flow_ctl flow_ctl;
918 cp210x_read_u32_reg(port, CP210X_GET_BAUDRATE, &baud);
920 dev_dbg(dev, "%s - baud rate = %d\n", __func__, baud);
925 cp210x_get_line_ctl(port, &bits);
927 switch (bits & BITS_DATA_MASK) {
929 dev_dbg(dev, "%s - data bits = 5\n", __func__);
933 dev_dbg(dev, "%s - data bits = 6\n", __func__);
937 dev_dbg(dev, "%s - data bits = 7\n", __func__);
941 dev_dbg(dev, "%s - data bits = 8\n", __func__);
945 dev_dbg(dev, "%s - data bits = 9 (not supported, using 8 data bits)\n", __func__);
947 bits &= ~BITS_DATA_MASK;
949 cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, bits);
952 dev_dbg(dev, "%s - Unknown number of data bits, using 8\n", __func__);
954 bits &= ~BITS_DATA_MASK;
956 cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, bits);
960 switch (bits & BITS_PARITY_MASK) {
961 case BITS_PARITY_NONE:
962 dev_dbg(dev, "%s - parity = NONE\n", __func__);
965 case BITS_PARITY_ODD:
966 dev_dbg(dev, "%s - parity = ODD\n", __func__);
967 cflag |= (PARENB|PARODD);
969 case BITS_PARITY_EVEN:
970 dev_dbg(dev, "%s - parity = EVEN\n", __func__);
974 case BITS_PARITY_MARK:
975 dev_dbg(dev, "%s - parity = MARK\n", __func__);
976 cflag |= (PARENB|PARODD|CMSPAR);
978 case BITS_PARITY_SPACE:
979 dev_dbg(dev, "%s - parity = SPACE\n", __func__);
981 cflag |= (PARENB|CMSPAR);
984 dev_dbg(dev, "%s - Unknown parity mode, disabling parity\n", __func__);
986 bits &= ~BITS_PARITY_MASK;
987 cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, bits);
992 switch (bits & BITS_STOP_MASK) {
994 dev_dbg(dev, "%s - stop bits = 1\n", __func__);
997 dev_dbg(dev, "%s - stop bits = 1.5 (not supported, using 1 stop bit)\n", __func__);
998 bits &= ~BITS_STOP_MASK;
999 cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, bits);
1002 dev_dbg(dev, "%s - stop bits = 2\n", __func__);
1006 dev_dbg(dev, "%s - Unknown number of stop bits, using 1 stop bit\n", __func__);
1007 bits &= ~BITS_STOP_MASK;
1008 cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, bits);
1012 cp210x_read_reg_block(port, CP210X_GET_FLOW, &flow_ctl,
1014 ctl_hs = le32_to_cpu(flow_ctl.ulControlHandshake);
1015 if (ctl_hs & CP210X_SERIAL_CTS_HANDSHAKE) {
1016 dev_dbg(dev, "%s - flow control = CRTSCTS\n", __func__);
1018 * When the port is closed, the CP210x hardware disables
1019 * auto-RTS and RTS is deasserted but it leaves auto-CTS when
1020 * in hardware flow control mode. When re-opening the port, if
1021 * auto-CTS is enabled on the cp210x, then auto-RTS must be
1022 * re-enabled in the driver.
1024 flow_repl = le32_to_cpu(flow_ctl.ulFlowReplace);
1025 flow_repl &= ~CP210X_SERIAL_RTS_MASK;
1026 flow_repl |= CP210X_SERIAL_RTS_SHIFT(CP210X_SERIAL_RTS_FLOW_CTL);
1027 flow_ctl.ulFlowReplace = cpu_to_le32(flow_repl);
1028 cp210x_write_reg_block(port,
1035 dev_dbg(dev, "%s - flow control = NONE\n", __func__);
1042 struct cp210x_rate {
1047 static const struct cp210x_rate cp210x_an205_table1[] = {
1076 { 921600, UINT_MAX }
1080 * Quantises the baud rate as per AN205 Table 1
1082 static speed_t cp210x_get_an205_rate(speed_t baud)
1086 for (i = 0; i < ARRAY_SIZE(cp210x_an205_table1); ++i) {
1087 if (baud <= cp210x_an205_table1[i].high)
1091 return cp210x_an205_table1[i].rate;
1094 static speed_t cp210x_get_actual_rate(struct usb_serial *serial, speed_t baud)
1096 struct cp210x_serial_private *priv = usb_get_serial_data(serial);
1097 unsigned int prescale = 1;
1100 baud = clamp(baud, 300u, priv->max_speed);
1105 div = DIV_ROUND_CLOSEST(48000000, 2 * prescale * baud);
1106 baud = 48000000 / (2 * prescale * div);
1112 * CP2101 supports the following baud rates:
1114 * 300, 600, 1200, 1800, 2400, 4800, 7200, 9600, 14400, 19200, 28800,
1115 * 38400, 56000, 57600, 115200, 128000, 230400, 460800, 921600
1117 * CP2102 and CP2103 support the following additional rates:
1119 * 4000, 16000, 51200, 64000, 76800, 153600, 250000, 256000, 500000,
1122 * The device will map a requested rate to a supported one, but the result
1123 * of requests for rates greater than 1053257 is undefined (see AN205).
1125 * CP2104, CP2105 and CP2110 support most rates up to 2M, 921k and 1M baud,
1126 * respectively, with an error less than 1%. The actual rates are determined
1129 * div = round(freq / (2 x prescale x request))
1130 * actual = freq / (2 x prescale x div)
1132 * For CP2104 and CP2105 freq is 48Mhz and prescale is 4 for request <= 365bps
1134 * For CP2110 freq is 24Mhz and prescale is 4 for request <= 300bps or 1
1137 static void cp210x_change_speed(struct tty_struct *tty,
1138 struct usb_serial_port *port, struct ktermios *old_termios)
1140 struct usb_serial *serial = port->serial;
1141 struct cp210x_serial_private *priv = usb_get_serial_data(serial);
1144 baud = tty->termios.c_ospeed;
1147 * This maps the requested rate to the actual rate, a valid rate on
1148 * cp2102 or cp2103, or to an arbitrary rate in [1M, max_speed].
1150 * NOTE: B0 is not implemented.
1152 if (priv->use_actual_rate)
1153 baud = cp210x_get_actual_rate(serial, baud);
1154 else if (baud < 1000000)
1155 baud = cp210x_get_an205_rate(baud);
1156 else if (baud > priv->max_speed)
1157 baud = priv->max_speed;
1159 dev_dbg(&port->dev, "%s - setting baud rate to %u\n", __func__, baud);
1160 if (cp210x_write_u32_reg(port, CP210X_SET_BAUDRATE, baud)) {
1161 dev_warn(&port->dev, "failed to set baud rate to %u\n", baud);
1163 baud = old_termios->c_ospeed;
1168 tty_encode_baud_rate(tty, baud, baud);
1171 static void cp210x_set_termios(struct tty_struct *tty,
1172 struct usb_serial_port *port, struct ktermios *old_termios)
1174 struct device *dev = &port->dev;
1175 unsigned int cflag, old_cflag;
1178 cflag = tty->termios.c_cflag;
1179 old_cflag = old_termios->c_cflag;
1181 if (tty->termios.c_ospeed != old_termios->c_ospeed)
1182 cp210x_change_speed(tty, port, old_termios);
1184 /* If the number of data bits is to be updated */
1185 if ((cflag & CSIZE) != (old_cflag & CSIZE)) {
1186 cp210x_get_line_ctl(port, &bits);
1187 bits &= ~BITS_DATA_MASK;
1188 switch (cflag & CSIZE) {
1190 bits |= BITS_DATA_5;
1191 dev_dbg(dev, "%s - data bits = 5\n", __func__);
1194 bits |= BITS_DATA_6;
1195 dev_dbg(dev, "%s - data bits = 6\n", __func__);
1198 bits |= BITS_DATA_7;
1199 dev_dbg(dev, "%s - data bits = 7\n", __func__);
1203 bits |= BITS_DATA_8;
1204 dev_dbg(dev, "%s - data bits = 8\n", __func__);
1207 if (cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, bits))
1208 dev_dbg(dev, "Number of data bits requested not supported by device\n");
1211 if ((cflag & (PARENB|PARODD|CMSPAR)) !=
1212 (old_cflag & (PARENB|PARODD|CMSPAR))) {
1213 cp210x_get_line_ctl(port, &bits);
1214 bits &= ~BITS_PARITY_MASK;
1215 if (cflag & PARENB) {
1216 if (cflag & CMSPAR) {
1217 if (cflag & PARODD) {
1218 bits |= BITS_PARITY_MARK;
1219 dev_dbg(dev, "%s - parity = MARK\n", __func__);
1221 bits |= BITS_PARITY_SPACE;
1222 dev_dbg(dev, "%s - parity = SPACE\n", __func__);
1225 if (cflag & PARODD) {
1226 bits |= BITS_PARITY_ODD;
1227 dev_dbg(dev, "%s - parity = ODD\n", __func__);
1229 bits |= BITS_PARITY_EVEN;
1230 dev_dbg(dev, "%s - parity = EVEN\n", __func__);
1234 if (cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, bits))
1235 dev_dbg(dev, "Parity mode not supported by device\n");
1238 if ((cflag & CSTOPB) != (old_cflag & CSTOPB)) {
1239 cp210x_get_line_ctl(port, &bits);
1240 bits &= ~BITS_STOP_MASK;
1241 if (cflag & CSTOPB) {
1242 bits |= BITS_STOP_2;
1243 dev_dbg(dev, "%s - stop bits = 2\n", __func__);
1245 bits |= BITS_STOP_1;
1246 dev_dbg(dev, "%s - stop bits = 1\n", __func__);
1248 if (cp210x_write_u16_reg(port, CP210X_SET_LINE_CTL, bits))
1249 dev_dbg(dev, "Number of stop bits requested not supported by device\n");
1252 if ((cflag & CRTSCTS) != (old_cflag & CRTSCTS)) {
1253 struct cp210x_flow_ctl flow_ctl;
1257 cp210x_read_reg_block(port, CP210X_GET_FLOW, &flow_ctl,
1259 ctl_hs = le32_to_cpu(flow_ctl.ulControlHandshake);
1260 flow_repl = le32_to_cpu(flow_ctl.ulFlowReplace);
1261 dev_dbg(dev, "%s - read ulControlHandshake=0x%08x, ulFlowReplace=0x%08x\n",
1262 __func__, ctl_hs, flow_repl);
1264 ctl_hs &= ~CP210X_SERIAL_DSR_HANDSHAKE;
1265 ctl_hs &= ~CP210X_SERIAL_DCD_HANDSHAKE;
1266 ctl_hs &= ~CP210X_SERIAL_DSR_SENSITIVITY;
1267 ctl_hs &= ~CP210X_SERIAL_DTR_MASK;
1268 ctl_hs |= CP210X_SERIAL_DTR_SHIFT(CP210X_SERIAL_DTR_ACTIVE);
1269 if (cflag & CRTSCTS) {
1270 ctl_hs |= CP210X_SERIAL_CTS_HANDSHAKE;
1272 flow_repl &= ~CP210X_SERIAL_RTS_MASK;
1273 flow_repl |= CP210X_SERIAL_RTS_SHIFT(
1274 CP210X_SERIAL_RTS_FLOW_CTL);
1275 dev_dbg(dev, "%s - flow control = CRTSCTS\n", __func__);
1277 ctl_hs &= ~CP210X_SERIAL_CTS_HANDSHAKE;
1279 flow_repl &= ~CP210X_SERIAL_RTS_MASK;
1280 flow_repl |= CP210X_SERIAL_RTS_SHIFT(
1281 CP210X_SERIAL_RTS_ACTIVE);
1282 dev_dbg(dev, "%s - flow control = NONE\n", __func__);
1285 dev_dbg(dev, "%s - write ulControlHandshake=0x%08x, ulFlowReplace=0x%08x\n",
1286 __func__, ctl_hs, flow_repl);
1287 flow_ctl.ulControlHandshake = cpu_to_le32(ctl_hs);
1288 flow_ctl.ulFlowReplace = cpu_to_le32(flow_repl);
1289 cp210x_write_reg_block(port, CP210X_SET_FLOW, &flow_ctl,
1295 static int cp210x_tiocmset(struct tty_struct *tty,
1296 unsigned int set, unsigned int clear)
1298 struct usb_serial_port *port = tty->driver_data;
1299 return cp210x_tiocmset_port(port, set, clear);
1302 static int cp210x_tiocmset_port(struct usb_serial_port *port,
1303 unsigned int set, unsigned int clear)
1307 if (set & TIOCM_RTS) {
1308 control |= CONTROL_RTS;
1309 control |= CONTROL_WRITE_RTS;
1311 if (set & TIOCM_DTR) {
1312 control |= CONTROL_DTR;
1313 control |= CONTROL_WRITE_DTR;
1315 if (clear & TIOCM_RTS) {
1316 control &= ~CONTROL_RTS;
1317 control |= CONTROL_WRITE_RTS;
1319 if (clear & TIOCM_DTR) {
1320 control &= ~CONTROL_DTR;
1321 control |= CONTROL_WRITE_DTR;
1324 dev_dbg(&port->dev, "%s - control = 0x%.4x\n", __func__, control);
1326 return cp210x_write_u16_reg(port, CP210X_SET_MHS, control);
1329 static void cp210x_dtr_rts(struct usb_serial_port *p, int on)
1332 cp210x_tiocmset_port(p, TIOCM_DTR|TIOCM_RTS, 0);
1334 cp210x_tiocmset_port(p, 0, TIOCM_DTR|TIOCM_RTS);
1337 static int cp210x_tiocmget(struct tty_struct *tty)
1339 struct usb_serial_port *port = tty->driver_data;
1343 result = cp210x_read_u8_reg(port, CP210X_GET_MDMSTS, &control);
1347 result = ((control & CONTROL_DTR) ? TIOCM_DTR : 0)
1348 |((control & CONTROL_RTS) ? TIOCM_RTS : 0)
1349 |((control & CONTROL_CTS) ? TIOCM_CTS : 0)
1350 |((control & CONTROL_DSR) ? TIOCM_DSR : 0)
1351 |((control & CONTROL_RING)? TIOCM_RI : 0)
1352 |((control & CONTROL_DCD) ? TIOCM_CD : 0);
1354 dev_dbg(&port->dev, "%s - control = 0x%.2x\n", __func__, control);
1359 static void cp210x_break_ctl(struct tty_struct *tty, int break_state)
1361 struct usb_serial_port *port = tty->driver_data;
1364 if (break_state == 0)
1368 dev_dbg(&port->dev, "%s - turning break %s\n", __func__,
1369 state == BREAK_OFF ? "off" : "on");
1370 cp210x_write_u16_reg(port, CP210X_SET_BREAK, state);
1373 #ifdef CONFIG_GPIOLIB
1374 static int cp210x_gpio_request(struct gpio_chip *gc, unsigned int offset)
1376 struct usb_serial *serial = gpiochip_get_data(gc);
1377 struct cp210x_serial_private *priv = usb_get_serial_data(serial);
1379 if (priv->gpio_altfunc & BIT(offset))
1385 static int cp210x_gpio_get(struct gpio_chip *gc, unsigned int gpio)
1387 struct usb_serial *serial = gpiochip_get_data(gc);
1388 struct cp210x_serial_private *priv = usb_get_serial_data(serial);
1389 u8 req_type = REQTYPE_DEVICE_TO_HOST;
1393 if (priv->partnum == CP210X_PARTNUM_CP2105)
1394 req_type = REQTYPE_INTERFACE_TO_HOST;
1396 result = usb_autopm_get_interface(serial->interface);
1400 result = cp210x_read_vendor_block(serial, req_type,
1401 CP210X_READ_LATCH, &buf, sizeof(buf));
1402 usb_autopm_put_interface(serial->interface);
1406 return !!(buf & BIT(gpio));
1409 static void cp210x_gpio_set(struct gpio_chip *gc, unsigned int gpio, int value)
1411 struct usb_serial *serial = gpiochip_get_data(gc);
1412 struct cp210x_serial_private *priv = usb_get_serial_data(serial);
1413 struct cp210x_gpio_write buf;
1417 buf.state = BIT(gpio);
1421 buf.mask = BIT(gpio);
1423 result = usb_autopm_get_interface(serial->interface);
1427 if (priv->partnum == CP210X_PARTNUM_CP2105) {
1428 result = cp210x_write_vendor_block(serial,
1429 REQTYPE_HOST_TO_INTERFACE,
1430 CP210X_WRITE_LATCH, &buf,
1433 u16 wIndex = buf.state << 8 | buf.mask;
1435 result = usb_control_msg(serial->dev,
1436 usb_sndctrlpipe(serial->dev, 0),
1437 CP210X_VENDOR_SPECIFIC,
1438 REQTYPE_HOST_TO_DEVICE,
1441 NULL, 0, USB_CTRL_SET_TIMEOUT);
1444 usb_autopm_put_interface(serial->interface);
1447 dev_err(&serial->interface->dev, "failed to set GPIO value: %d\n",
1452 static int cp210x_gpio_direction_get(struct gpio_chip *gc, unsigned int gpio)
1454 struct usb_serial *serial = gpiochip_get_data(gc);
1455 struct cp210x_serial_private *priv = usb_get_serial_data(serial);
1457 return priv->gpio_input & BIT(gpio);
1460 static int cp210x_gpio_direction_input(struct gpio_chip *gc, unsigned int gpio)
1462 struct usb_serial *serial = gpiochip_get_data(gc);
1463 struct cp210x_serial_private *priv = usb_get_serial_data(serial);
1465 if (priv->partnum == CP210X_PARTNUM_CP2105) {
1466 /* hardware does not support an input mode */
1470 /* push-pull pins cannot be changed to be inputs */
1471 if (priv->gpio_pushpull & BIT(gpio))
1474 /* make sure to release pin if it is being driven low */
1475 cp210x_gpio_set(gc, gpio, 1);
1477 priv->gpio_input |= BIT(gpio);
1482 static int cp210x_gpio_direction_output(struct gpio_chip *gc, unsigned int gpio,
1485 struct usb_serial *serial = gpiochip_get_data(gc);
1486 struct cp210x_serial_private *priv = usb_get_serial_data(serial);
1488 priv->gpio_input &= ~BIT(gpio);
1489 cp210x_gpio_set(gc, gpio, value);
1494 static int cp210x_gpio_set_config(struct gpio_chip *gc, unsigned int gpio,
1495 unsigned long config)
1497 struct usb_serial *serial = gpiochip_get_data(gc);
1498 struct cp210x_serial_private *priv = usb_get_serial_data(serial);
1499 enum pin_config_param param = pinconf_to_config_param(config);
1501 /* Succeed only if in correct mode (this can't be set at runtime) */
1502 if ((param == PIN_CONFIG_DRIVE_PUSH_PULL) &&
1503 (priv->gpio_pushpull & BIT(gpio)))
1506 if ((param == PIN_CONFIG_DRIVE_OPEN_DRAIN) &&
1507 !(priv->gpio_pushpull & BIT(gpio)))
1514 * This function is for configuring GPIO using shared pins, where other signals
1515 * are made unavailable by configuring the use of GPIO. This is believed to be
1516 * only applicable to the cp2105 at this point, the other devices supported by
1517 * this driver that provide GPIO do so in a way that does not impact other
1518 * signals and are thus expected to have very different initialisation.
1520 static int cp2105_gpioconf_init(struct usb_serial *serial)
1522 struct cp210x_serial_private *priv = usb_get_serial_data(serial);
1523 struct cp210x_pin_mode mode;
1524 struct cp210x_config config;
1525 u8 intf_num = cp210x_interface_num(serial);
1529 result = cp210x_read_vendor_block(serial, REQTYPE_DEVICE_TO_HOST,
1530 CP210X_GET_DEVICEMODE, &mode,
1535 result = cp210x_read_vendor_block(serial, REQTYPE_DEVICE_TO_HOST,
1536 CP210X_GET_PORTCONFIG, &config,
1541 /* 2 banks of GPIO - One for the pins taken from each serial port */
1542 if (intf_num == 0) {
1545 if (mode.eci == CP210X_PIN_MODE_MODEM) {
1546 /* mark all GPIOs of this interface as reserved */
1547 priv->gpio_altfunc = 0xff;
1551 iface_config = config.eci_cfg;
1552 priv->gpio_pushpull = (u8)((le16_to_cpu(config.gpio_mode) &
1553 CP210X_ECI_GPIO_MODE_MASK) >>
1554 CP210X_ECI_GPIO_MODE_OFFSET);
1555 } else if (intf_num == 1) {
1558 if (mode.sci == CP210X_PIN_MODE_MODEM) {
1559 /* mark all GPIOs of this interface as reserved */
1560 priv->gpio_altfunc = 0xff;
1564 iface_config = config.sci_cfg;
1565 priv->gpio_pushpull = (u8)((le16_to_cpu(config.gpio_mode) &
1566 CP210X_SCI_GPIO_MODE_MASK) >>
1567 CP210X_SCI_GPIO_MODE_OFFSET);
1572 /* mark all pins which are not in GPIO mode */
1573 if (iface_config & CP2105_GPIO0_TXLED_MODE) /* GPIO 0 */
1574 priv->gpio_altfunc |= BIT(0);
1575 if (iface_config & (CP2105_GPIO1_RXLED_MODE | /* GPIO 1 */
1576 CP2105_GPIO1_RS485_MODE))
1577 priv->gpio_altfunc |= BIT(1);
1579 /* driver implementation for CP2105 only supports outputs */
1580 priv->gpio_input = 0;
1585 static int cp2102n_gpioconf_init(struct usb_serial *serial)
1587 struct cp210x_serial_private *priv = usb_get_serial_data(serial);
1588 const u16 config_size = 0x02a6;
1599 * Retrieve device configuration from the device.
1600 * The array received contains all customization settings done at the
1601 * factory/manufacturer. Format of the array is documented at the
1602 * time of writing at:
1603 * https://www.silabs.com/community/interface/knowledge-base.entry.html/2017/03/31/cp2102n_setconfig-xsfa
1605 config_buf = kmalloc(config_size, GFP_KERNEL);
1609 result = cp210x_read_vendor_block(serial,
1610 REQTYPE_DEVICE_TO_HOST,
1611 CP210X_READ_2NCONFIG,
1619 config_version = config_buf[CP210X_2NCONFIG_CONFIG_VERSION_IDX];
1620 gpio_pushpull = config_buf[CP210X_2NCONFIG_GPIO_MODE_IDX];
1621 gpio_ctrl = config_buf[CP210X_2NCONFIG_GPIO_CONTROL_IDX];
1622 gpio_rst_latch = config_buf[CP210X_2NCONFIG_GPIO_RSTLATCH_IDX];
1626 /* Make sure this is a config format we understand. */
1627 if (config_version != 0x01)
1631 * We only support 4 GPIOs even on the QFN28 package, because
1632 * config locations of GPIOs 4-6 determined using reverse
1633 * engineering revealed conflicting offsets with other
1634 * documented functions. So we'll just play it safe for now.
1639 * Get default pin states after reset. Needed so we can determine
1640 * the direction of an open-drain pin.
1642 gpio_latch = (gpio_rst_latch >> 3) & 0x0f;
1644 /* 0 indicates open-drain mode, 1 is push-pull */
1645 priv->gpio_pushpull = (gpio_pushpull >> 3) & 0x0f;
1647 /* 0 indicates GPIO mode, 1 is alternate function */
1648 if (priv->partnum == CP210X_PARTNUM_CP2102N_QFN20) {
1649 /* QFN20 is special... */
1650 if (gpio_ctrl & CP2102N_QFN20_GPIO0_CLK_MODE) /* GPIO 0 */
1651 priv->gpio_altfunc |= BIT(0);
1652 if (gpio_ctrl & CP2102N_QFN20_GPIO1_RS485_MODE) /* GPIO 1 */
1653 priv->gpio_altfunc |= BIT(1);
1654 if (gpio_ctrl & CP2102N_QFN20_GPIO2_TXLED_MODE) /* GPIO 2 */
1655 priv->gpio_altfunc |= BIT(2);
1656 if (gpio_ctrl & CP2102N_QFN20_GPIO3_RXLED_MODE) /* GPIO 3 */
1657 priv->gpio_altfunc |= BIT(3);
1659 priv->gpio_altfunc = (gpio_ctrl >> 2) & 0x0f;
1663 * The CP2102N does not strictly has input and output pin modes,
1664 * it only knows open-drain and push-pull modes which is set at
1665 * factory. An open-drain pin can function both as an
1666 * input or an output. We emulate input mode for open-drain pins
1667 * by making sure they are not driven low, and we do not allow
1668 * push-pull pins to be set as an input.
1670 for (i = 0; i < priv->gc.ngpio; ++i) {
1672 * Set direction to "input" iff pin is open-drain and reset
1675 if (!(priv->gpio_pushpull & BIT(i)) && (gpio_latch & BIT(i)))
1676 priv->gpio_input |= BIT(i);
1682 static int cp210x_gpio_init(struct usb_serial *serial)
1684 struct cp210x_serial_private *priv = usb_get_serial_data(serial);
1687 switch (priv->partnum) {
1688 case CP210X_PARTNUM_CP2105:
1689 result = cp2105_gpioconf_init(serial);
1691 case CP210X_PARTNUM_CP2102N_QFN28:
1692 case CP210X_PARTNUM_CP2102N_QFN24:
1693 case CP210X_PARTNUM_CP2102N_QFN20:
1694 result = cp2102n_gpioconf_init(serial);
1703 priv->gc.label = "cp210x";
1704 priv->gc.request = cp210x_gpio_request;
1705 priv->gc.get_direction = cp210x_gpio_direction_get;
1706 priv->gc.direction_input = cp210x_gpio_direction_input;
1707 priv->gc.direction_output = cp210x_gpio_direction_output;
1708 priv->gc.get = cp210x_gpio_get;
1709 priv->gc.set = cp210x_gpio_set;
1710 priv->gc.set_config = cp210x_gpio_set_config;
1711 priv->gc.owner = THIS_MODULE;
1712 priv->gc.parent = &serial->interface->dev;
1714 priv->gc.can_sleep = true;
1716 result = gpiochip_add_data(&priv->gc, serial);
1718 priv->gpio_registered = true;
1723 static void cp210x_gpio_remove(struct usb_serial *serial)
1725 struct cp210x_serial_private *priv = usb_get_serial_data(serial);
1727 if (priv->gpio_registered) {
1728 gpiochip_remove(&priv->gc);
1729 priv->gpio_registered = false;
1735 static int cp210x_gpio_init(struct usb_serial *serial)
1740 static void cp210x_gpio_remove(struct usb_serial *serial)
1747 static int cp210x_port_probe(struct usb_serial_port *port)
1749 struct usb_serial *serial = port->serial;
1750 struct cp210x_port_private *port_priv;
1753 port_priv = kzalloc(sizeof(*port_priv), GFP_KERNEL);
1757 port_priv->bInterfaceNumber = cp210x_interface_num(serial);
1759 usb_set_serial_port_data(port, port_priv);
1761 ret = cp210x_detect_swapped_line_ctl(port);
1770 static int cp210x_port_remove(struct usb_serial_port *port)
1772 struct cp210x_port_private *port_priv;
1774 port_priv = usb_get_serial_port_data(port);
1780 static void cp210x_init_max_speed(struct usb_serial *serial)
1782 struct cp210x_serial_private *priv = usb_get_serial_data(serial);
1783 bool use_actual_rate = false;
1786 switch (priv->partnum) {
1787 case CP210X_PARTNUM_CP2101:
1790 case CP210X_PARTNUM_CP2102:
1791 case CP210X_PARTNUM_CP2103:
1794 case CP210X_PARTNUM_CP2104:
1795 use_actual_rate = true;
1798 case CP210X_PARTNUM_CP2108:
1801 case CP210X_PARTNUM_CP2105:
1802 if (cp210x_interface_num(serial) == 0) {
1803 use_actual_rate = true;
1804 max = 2000000; /* ECI */
1806 max = 921600; /* SCI */
1809 case CP210X_PARTNUM_CP2102N_QFN28:
1810 case CP210X_PARTNUM_CP2102N_QFN24:
1811 case CP210X_PARTNUM_CP2102N_QFN20:
1812 use_actual_rate = true;
1820 priv->max_speed = max;
1821 priv->use_actual_rate = use_actual_rate;
1824 static int cp210x_attach(struct usb_serial *serial)
1827 struct cp210x_serial_private *priv;
1829 priv = kzalloc(sizeof(*priv), GFP_KERNEL);
1833 result = cp210x_read_vendor_block(serial, REQTYPE_DEVICE_TO_HOST,
1834 CP210X_GET_PARTNUM, &priv->partnum,
1835 sizeof(priv->partnum));
1837 dev_warn(&serial->interface->dev,
1838 "querying part number failed\n");
1839 priv->partnum = CP210X_PARTNUM_UNKNOWN;
1842 usb_set_serial_data(serial, priv);
1844 cp210x_init_max_speed(serial);
1846 result = cp210x_gpio_init(serial);
1848 dev_err(&serial->interface->dev, "GPIO initialisation failed: %d\n",
1855 static void cp210x_disconnect(struct usb_serial *serial)
1857 cp210x_gpio_remove(serial);
1860 static void cp210x_release(struct usb_serial *serial)
1862 struct cp210x_serial_private *priv = usb_get_serial_data(serial);
1864 cp210x_gpio_remove(serial);
1869 module_usb_serial_driver(serial_drivers, id_table);
1871 MODULE_DESCRIPTION(DRIVER_DESC);
1872 MODULE_LICENSE("GPL v2");