drivers/tty/synclink_gt.c

   1 /*
   2  * Device driver for Microgate SyncLink GT serial adapters.
   3  *
   4  * written by Paul Fulghum for Microgate Corporation
   5  * paulkf@microgate.com
   6  *
   7  * Microgate and SyncLink are trademarks of Microgate Corporation
   8  *
   9  * This code is released under the GNU General Public License (GPL)
  10  *
  11  * THIS SOFTWARE IS PROVIDED ``AS IS'' AND ANY EXPRESS OR IMPLIED
  12  * WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES
  13  * OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
  14  * DISCLAIMED.  IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY DIRECT,
  15  * INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
  16  * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR
  17  * SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
  18  * HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
  19  * STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
  20  * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED
  21  * OF THE POSSIBILITY OF SUCH DAMAGE.
  22  */
  23
  24 /*
  25  * DEBUG OUTPUT DEFINITIONS
  26  *
  27  * uncomment lines below to enable specific types of debug output
  28  *
  29  * DBGINFO   information - most verbose output
  30  * DBGERR    serious errors
  31  * DBGBH     bottom half service routine debugging
  32  * DBGISR    interrupt service routine debugging
  33  * DBGDATA   output receive and transmit data
  34  * DBGTBUF   output transmit DMA buffers and registers
  35  * DBGRBUF   output receive DMA buffers and registers
  36  */
  37
  38 #define DBGINFO(fmt) if (debug_level >= DEBUG_LEVEL_INFO) printk fmt
  39 #define DBGERR(fmt) if (debug_level >= DEBUG_LEVEL_ERROR) printk fmt
  40 #define DBGBH(fmt) if (debug_level >= DEBUG_LEVEL_BH) printk fmt
  41 #define DBGISR(fmt) if (debug_level >= DEBUG_LEVEL_ISR) printk fmt
  42 #define DBGDATA(info, buf, size, label) if (debug_level >= DEBUG_LEVEL_DATA) trace_block((info), (buf), (size), (label))
  43 /*#define DBGTBUF(info) dump_tbufs(info)*/
  44 /*#define DBGRBUF(info) dump_rbufs(info)*/
  45
  46
  47 #include <linux/module.h>
  48 #include <linux/errno.h>
  49 #include <linux/signal.h>
  50 #include <linux/sched.h>
  51 #include <linux/timer.h>
  52 #include <linux/interrupt.h>
  53 #include <linux/pci.h>
  54 #include <linux/tty.h>
  55 #include <linux/tty_flip.h>
  56 #include <linux/serial.h>
  57 #include <linux/major.h>
  58 #include <linux/string.h>
  59 #include <linux/fcntl.h>
  60 #include <linux/ptrace.h>
  61 #include <linux/ioport.h>
  62 #include <linux/mm.h>
  63 #include <linux/seq_file.h>
  64 #include <linux/slab.h>
  65 #include <linux/netdevice.h>
  66 #include <linux/vmalloc.h>
  67 #include <linux/init.h>
  68 #include <linux/delay.h>
  69 #include <linux/ioctl.h>
  70 #include <linux/termios.h>
  71 #include <linux/bitops.h>
  72 #include <linux/workqueue.h>
  73 #include <linux/hdlc.h>
  74 #include <linux/synclink.h>
  75
  76 #include <asm/io.h>
  77 #include <asm/irq.h>
  78 #include <asm/dma.h>
  79 #include <asm/types.h>
  80 #include <linux/uaccess.h>
  81
  82 #if defined(CONFIG_HDLC) || (defined(CONFIG_HDLC_MODULE) && defined(CONFIG_SYNCLINK_GT_MODULE))
  83 #define SYNCLINK_GENERIC_HDLC 1
  84 #else
  85 #define SYNCLINK_GENERIC_HDLC 0
  86 #endif
  87
  88 /*
  89  * module identification
  90  */
  91 static char *driver_name     = "SyncLink GT";
  92 static char *slgt_driver_name = "synclink_gt";
  93 static char *tty_dev_prefix  = "ttySLG";
  94 MODULE_LICENSE("GPL");
  95 #define MGSL_MAGIC 0x5401
  96 #define MAX_DEVICES 32
  97
  98 static const struct pci_device_id pci_table[] = {
  99         {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
 100         {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT2_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
 101         {PCI_VENDOR_ID_MICROGATE, SYNCLINK_GT4_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
 102         {PCI_VENDOR_ID_MICROGATE, SYNCLINK_AC_DEVICE_ID, PCI_ANY_ID, PCI_ANY_ID,},
 103         {0,}, /* terminate list */
 104 };
 105 MODULE_DEVICE_TABLE(pci, pci_table);
 106
 107 static int  init_one(struct pci_dev *dev,const struct pci_device_id *ent);
 108 static void remove_one(struct pci_dev *dev);
 109 static struct pci_driver pci_driver = {
 110         .name           = "synclink_gt",
 111         .id_table       = pci_table,
 112         .probe          = init_one,
 113         .remove         = remove_one,
 114 };
 115
 116 static bool pci_registered;
 117
 118 /*
 119  * module configuration and status
 120  */
 121 static struct slgt_info *slgt_device_list;
 122 static int slgt_device_count;
 123
 124 static int ttymajor;
 125 static int debug_level;
 126 static int maxframe[MAX_DEVICES];
 127
 128 module_param(ttymajor, int, 0);
 129 module_param(debug_level, int, 0);
 130 module_param_array(maxframe, int, NULL, 0);
 131
 132 MODULE_PARM_DESC(ttymajor, "TTY major device number override: 0=auto assigned");
 133 MODULE_PARM_DESC(debug_level, "Debug syslog output: 0=disabled, 1 to 5=increasing detail");
 134 MODULE_PARM_DESC(maxframe, "Maximum frame size used by device (4096 to 65535)");
 135
 136 /*
 137  * tty support and callbacks
 138  */
 139 static struct tty_driver *serial_driver;
 140
 141 static int  open(struct tty_struct *tty, struct file * filp);
 142 static void close(struct tty_struct *tty, struct file * filp);
 143 static void hangup(struct tty_struct *tty);
 144 static void set_termios(struct tty_struct *tty, struct ktermios *old_termios);
 145
 146 static int  write(struct tty_struct *tty, const unsigned char *buf, int count);
 147 static int put_char(struct tty_struct *tty, unsigned char ch);
 148 static void send_xchar(struct tty_struct *tty, char ch);
 149 static void wait_until_sent(struct tty_struct *tty, int timeout);
 150 static int  write_room(struct tty_struct *tty);
 151 static void flush_chars(struct tty_struct *tty);
 152 static void flush_buffer(struct tty_struct *tty);
 153 static void tx_hold(struct tty_struct *tty);
 154 static void tx_release(struct tty_struct *tty);
 155
 156 static int  ioctl(struct tty_struct *tty, unsigned int cmd, unsigned long arg);
 157 static int  chars_in_buffer(struct tty_struct *tty);
 158 static void throttle(struct tty_struct * tty);
 159 static void unthrottle(struct tty_struct * tty);
 160 static int set_break(struct tty_struct *tty, int break_state);
 161
 162 /*
 163  * generic HDLC support and callbacks
 164  */
 165 #if SYNCLINK_GENERIC_HDLC
 166 #define dev_to_port(D) (dev_to_hdlc(D)->priv)
 167 static void hdlcdev_tx_done(struct slgt_info *info);
 168 static void hdlcdev_rx(struct slgt_info *info, char *buf, int size);
 169 static int  hdlcdev_init(struct slgt_info *info);
 170 static void hdlcdev_exit(struct slgt_info *info);
 171 #endif
 172
 173
 174 /*
 175  * device specific structures, macros and functions
 176  */
 177
 178 #define SLGT_MAX_PORTS 4
 179 #define SLGT_REG_SIZE  256
 180
 181 /*
 182  * conditional wait facility
 183  */
 184 struct cond_wait {
 185         struct cond_wait *next;
 186         wait_queue_head_t q;
 187         wait_queue_entry_t wait;
 188         unsigned int data;
 189 };
 190 static void init_cond_wait(struct cond_wait *w, unsigned int data);
 191 static void add_cond_wait(struct cond_wait **head, struct cond_wait *w);
 192 static void remove_cond_wait(struct cond_wait **head, struct cond_wait *w);
 193 static void flush_cond_wait(struct cond_wait **head);
 194
 195 /*
 196  * DMA buffer descriptor and access macros
 197  */
 198 struct slgt_desc
 199 {
 200         __le16 count;
 201         __le16 status;
 202         __le32 pbuf;  /* physical address of data buffer */
 203         __le32 next;  /* physical address of next descriptor */
 204
 205         /* driver book keeping */
 206         char *buf;          /* virtual  address of data buffer */
 207         unsigned int pdesc; /* physical address of this descriptor */
 208         dma_addr_t buf_dma_addr;
 209         unsigned short buf_count;
 210 };
 211
 212 #define set_desc_buffer(a,b) (a).pbuf = cpu_to_le32((unsigned int)(b))
 213 #define set_desc_next(a,b) (a).next   = cpu_to_le32((unsigned int)(b))
 214 #define set_desc_count(a,b)(a).count  = cpu_to_le16((unsigned short)(b))
 215 #define set_desc_eof(a,b)  (a).status = cpu_to_le16((b) ? (le16_to_cpu((a).status) | BIT0) : (le16_to_cpu((a).status) & ~BIT0))
 216 #define set_desc_status(a, b) (a).status = cpu_to_le16((unsigned short)(b))
 217 #define desc_count(a)      (le16_to_cpu((a).count))
 218 #define desc_status(a)     (le16_to_cpu((a).status))
 219 #define desc_complete(a)   (le16_to_cpu((a).status) & BIT15)
 220 #define desc_eof(a)        (le16_to_cpu((a).status) & BIT2)
 221 #define desc_crc_error(a)  (le16_to_cpu((a).status) & BIT1)
 222 #define desc_abort(a)      (le16_to_cpu((a).status) & BIT0)
 223 #define desc_residue(a)    ((le16_to_cpu((a).status) & 0x38) >> 3)
 224
 225 struct _input_signal_events {
 226         int ri_up;
 227         int ri_down;
 228         int dsr_up;
 229         int dsr_down;
 230         int dcd_up;
 231         int dcd_down;
 232         int cts_up;
 233         int cts_down;
 234 };
 235
 236 /*
 237  * device instance data structure
 238  */
 239 struct slgt_info {
 240         void *if_ptr;           /* General purpose pointer (used by SPPP) */
 241         struct tty_port port;
 242
 243         struct slgt_info *next_device;  /* device list link */
 244
 245         int magic;
 246
 247         char device_name[25];
 248         struct pci_dev *pdev;
 249
 250         int port_count;  /* count of ports on adapter */
 251         int adapter_num; /* adapter instance number */
 252         int port_num;    /* port instance number */
 253
 254         /* array of pointers to port contexts on this adapter */
 255         struct slgt_info *port_array[SLGT_MAX_PORTS];
 256
 257         int                     line;           /* tty line instance number */
 258
 259         struct mgsl_icount      icount;
 260
 261         int                     timeout;
 262         int                     x_char;         /* xon/xoff character */
 263         unsigned int            read_status_mask;
 264         unsigned int            ignore_status_mask;
 265
 266         wait_queue_head_t       status_event_wait_q;
 267         wait_queue_head_t       event_wait_q;
 268         struct timer_list       tx_timer;
 269         struct timer_list       rx_timer;
 270
 271         unsigned int            gpio_present;
 272         struct cond_wait        *gpio_wait_q;
 273
 274         spinlock_t lock;        /* spinlock for synchronizing with ISR */
 275
 276         struct work_struct task;
 277         u32 pending_bh;
 278         bool bh_requested;
 279         bool bh_running;
 280
 281         int isr_overflow;
 282         bool irq_requested;     /* true if IRQ requested */
 283         bool irq_occurred;      /* for diagnostics use */
 284
 285         /* device configuration */
 286
 287         unsigned int bus_type;
 288         unsigned int irq_level;
 289         unsigned long irq_flags;
 290
 291         unsigned char __iomem * reg_addr;  /* memory mapped registers address */
 292         u32 phys_reg_addr;
 293         bool reg_addr_requested;
 294
 295         MGSL_PARAMS params;       /* communications parameters */
 296         u32 idle_mode;
 297         u32 max_frame_size;       /* as set by device config */
 298
 299         unsigned int rbuf_fill_level;
 300         unsigned int rx_pio;
 301         unsigned int if_mode;
 302         unsigned int base_clock;
 303         unsigned int xsync;
 304         unsigned int xctrl;
 305
 306         /* device status */
 307
 308         bool rx_enabled;
 309         bool rx_restart;
 310
 311         bool tx_enabled;
 312         bool tx_active;
 313
 314         unsigned char signals;    /* serial signal states */
 315         int init_error;  /* initialization error */
 316
 317         unsigned char *tx_buf;
 318         int tx_count;
 319
 320         char *flag_buf;
 321         bool drop_rts_on_tx_done;
 322         struct  _input_signal_events    input_signal_events;
 323
 324         int dcd_chkcount;       /* check counts to prevent */
 325         int cts_chkcount;       /* too many IRQs if a signal */
 326         int dsr_chkcount;       /* is floating */
 327         int ri_chkcount;
 328
 329         char *bufs;             /* virtual address of DMA buffer lists */
 330         dma_addr_t bufs_dma_addr; /* physical address of buffer descriptors */
 331
 332         unsigned int rbuf_count;
 333         struct slgt_desc *rbufs;
 334         unsigned int rbuf_current;
 335         unsigned int rbuf_index;
 336         unsigned int rbuf_fill_index;
 337         unsigned short rbuf_fill_count;
 338
 339         unsigned int tbuf_count;
 340         struct slgt_desc *tbufs;
 341         unsigned int tbuf_current;
 342         unsigned int tbuf_start;
 343
 344         unsigned char *tmp_rbuf;
 345         unsigned int tmp_rbuf_count;
 346
 347         /* SPPP/Cisco HDLC device parts */
 348
 349         int netcount;
 350         spinlock_t netlock;
 351 #if SYNCLINK_GENERIC_HDLC
 352         struct net_device *netdev;
 353 #endif
 354
 355 };
 356
 357 static MGSL_PARAMS default_params = {
 358         .mode            = MGSL_MODE_HDLC,
 359         .loopback        = 0,
 360         .flags           = HDLC_FLAG_UNDERRUN_ABORT15,
 361         .encoding        = HDLC_ENCODING_NRZI_SPACE,
 362         .clock_speed     = 0,
 363         .addr_filter     = 0xff,
 364         .crc_type        = HDLC_CRC_16_CCITT,
 365         .preamble_length = HDLC_PREAMBLE_LENGTH_8BITS,
 366         .preamble        = HDLC_PREAMBLE_PATTERN_NONE,
 367         .data_rate       = 9600,
 368         .data_bits       = 8,
 369         .stop_bits       = 1,
 370         .parity          = ASYNC_PARITY_NONE
 371 };
 372
 373
 374 #define BH_RECEIVE  1
 375 #define BH_TRANSMIT 2
 376 #define BH_STATUS   4
 377 #define IO_PIN_SHUTDOWN_LIMIT 100
 378
 379 #define DMABUFSIZE 256
 380 #define DESC_LIST_SIZE 4096
 381
 382 #define MASK_PARITY  BIT1
 383 #define MASK_FRAMING BIT0
 384 #define MASK_BREAK   BIT14
 385 #define MASK_OVERRUN BIT4
 386
 387 #define GSR   0x00 /* global status */
 388 #define JCR   0x04 /* JTAG control */
 389 #define IODR  0x08 /* GPIO direction */
 390 #define IOER  0x0c /* GPIO interrupt enable */
 391 #define IOVR  0x10 /* GPIO value */
 392 #define IOSR  0x14 /* GPIO interrupt status */
 393 #define TDR   0x80 /* tx data */
 394 #define RDR   0x80 /* rx data */
 395 #define TCR   0x82 /* tx control */
 396 #define TIR   0x84 /* tx idle */
 397 #define TPR   0x85 /* tx preamble */
 398 #define RCR   0x86 /* rx control */
 399 #define VCR   0x88 /* V.24 control */
 400 #define CCR   0x89 /* clock control */
 401 #define BDR   0x8a /* baud divisor */
 402 #define SCR   0x8c /* serial control */
 403 #define SSR   0x8e /* serial status */
 404 #define RDCSR 0x90 /* rx DMA control/status */
 405 #define TDCSR 0x94 /* tx DMA control/status */
 406 #define RDDAR 0x98 /* rx DMA descriptor address */
 407 #define TDDAR 0x9c /* tx DMA descriptor address */
 408 #define XSR   0x40 /* extended sync pattern */
 409 #define XCR   0x44 /* extended control */
 410
 411 #define RXIDLE      BIT14
 412 #define RXBREAK     BIT14
 413 #define IRQ_TXDATA  BIT13
 414 #define IRQ_TXIDLE  BIT12
 415 #define IRQ_TXUNDER BIT11 /* HDLC */
 416 #define IRQ_RXDATA  BIT10
 417 #define IRQ_RXIDLE  BIT9  /* HDLC */
 418 #define IRQ_RXBREAK BIT9  /* async */
 419 #define IRQ_RXOVER  BIT8
 420 #define IRQ_DSR     BIT7
 421 #define IRQ_CTS     BIT6
 422 #define IRQ_DCD     BIT5
 423 #define IRQ_RI      BIT4
 424 #define IRQ_ALL     0x3ff0
 425 #define IRQ_MASTER  BIT0
 426
 427 #define slgt_irq_on(info, mask) \
 428         wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) | (mask)))
 429 #define slgt_irq_off(info, mask) \
 430         wr_reg16((info), SCR, (unsigned short)(rd_reg16((info), SCR) & ~(mask)))
 431
 432 static __u8  rd_reg8(struct slgt_info *info, unsigned int addr);
 433 static void  wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value);
 434 static __u16 rd_reg16(struct slgt_info *info, unsigned int addr);
 435 static void  wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value);
 436 static __u32 rd_reg32(struct slgt_info *info, unsigned int addr);
 437 static void  wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value);
 438
 439 static void  msc_set_vcr(struct slgt_info *info);
 440
 441 static int  startup(struct slgt_info *info);
 442 static int  block_til_ready(struct tty_struct *tty, struct file * filp,struct slgt_info *info);
 443 static void shutdown(struct slgt_info *info);
 444 static void program_hw(struct slgt_info *info);
 445 static void change_params(struct slgt_info *info);
 446
 447 static int  register_test(struct slgt_info *info);
 448 static int  irq_test(struct slgt_info *info);
 449 static int  loopback_test(struct slgt_info *info);
 450 static int  adapter_test(struct slgt_info *info);
 451
 452 static void reset_adapter(struct slgt_info *info);
 453 static void reset_port(struct slgt_info *info);
 454 static void async_mode(struct slgt_info *info);
 455 static void sync_mode(struct slgt_info *info);
 456
 457 static void rx_stop(struct slgt_info *info);
 458 static void rx_start(struct slgt_info *info);
 459 static void reset_rbufs(struct slgt_info *info);
 460 static void free_rbufs(struct slgt_info *info, unsigned int first, unsigned int last);
 461 static void rdma_reset(struct slgt_info *info);
 462 static bool rx_get_frame(struct slgt_info *info);
 463 static bool rx_get_buf(struct slgt_info *info);
 464
 465 static void tx_start(struct slgt_info *info);
 466 static void tx_stop(struct slgt_info *info);
 467 static void tx_set_idle(struct slgt_info *info);
 468 static unsigned int free_tbuf_count(struct slgt_info *info);
 469 static unsigned int tbuf_bytes(struct slgt_info *info);
 470 static void reset_tbufs(struct slgt_info *info);
 471 static void tdma_reset(struct slgt_info *info);
 472 static bool tx_load(struct slgt_info *info, const char *buf, unsigned int count);
 473
 474 static void get_signals(struct slgt_info *info);
 475 static void set_signals(struct slgt_info *info);
 476 static void enable_loopback(struct slgt_info *info);
 477 static void set_rate(struct slgt_info *info, u32 data_rate);
 478
 479 static int  bh_action(struct slgt_info *info);
 480 static void bh_handler(struct work_struct *work);
 481 static void bh_transmit(struct slgt_info *info);
 482 static void isr_serial(struct slgt_info *info);
 483 static void isr_rdma(struct slgt_info *info);
 484 static void isr_txeom(struct slgt_info *info, unsigned short status);
 485 static void isr_tdma(struct slgt_info *info);
 486
 487 static int  alloc_dma_bufs(struct slgt_info *info);
 488 static void free_dma_bufs(struct slgt_info *info);
 489 static int  alloc_desc(struct slgt_info *info);
 490 static void free_desc(struct slgt_info *info);
 491 static int  alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count);
 492 static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count);
 493
 494 static int  alloc_tmp_rbuf(struct slgt_info *info);
 495 static void free_tmp_rbuf(struct slgt_info *info);
 496
 497 static void tx_timeout(unsigned long context);
 498 static void rx_timeout(unsigned long context);
 499
 500 /*
 501  * ioctl handlers
 502  */
 503 static int  get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount);
 504 static int  get_params(struct slgt_info *info, MGSL_PARAMS __user *params);
 505 static int  set_params(struct slgt_info *info, MGSL_PARAMS __user *params);
 506 static int  get_txidle(struct slgt_info *info, int __user *idle_mode);
 507 static int  set_txidle(struct slgt_info *info, int idle_mode);
 508 static int  tx_enable(struct slgt_info *info, int enable);
 509 static int  tx_abort(struct slgt_info *info);
 510 static int  rx_enable(struct slgt_info *info, int enable);
 511 static int  modem_input_wait(struct slgt_info *info,int arg);
 512 static int  wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr);
 513 static int  tiocmget(struct tty_struct *tty);
 514 static int  tiocmset(struct tty_struct *tty,
 515                                 unsigned int set, unsigned int clear);
 516 static int set_break(struct tty_struct *tty, int break_state);
 517 static int  get_interface(struct slgt_info *info, int __user *if_mode);
 518 static int  set_interface(struct slgt_info *info, int if_mode);
 519 static int  set_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
 520 static int  get_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
 521 static int  wait_gpio(struct slgt_info *info, struct gpio_desc __user *gpio);
 522 static int  get_xsync(struct slgt_info *info, int __user *if_mode);
 523 static int  set_xsync(struct slgt_info *info, int if_mode);
 524 static int  get_xctrl(struct slgt_info *info, int __user *if_mode);
 525 static int  set_xctrl(struct slgt_info *info, int if_mode);
 526
 527 /*
 528  * driver functions
 529  */
 530 static void add_device(struct slgt_info *info);
 531 static void device_init(int adapter_num, struct pci_dev *pdev);
 532 static int  claim_resources(struct slgt_info *info);
 533 static void release_resources(struct slgt_info *info);
 534
 535 /*
 536  * DEBUG OUTPUT CODE
 537  */
 538 #ifndef DBGINFO
 539 #define DBGINFO(fmt)
 540 #endif
 541 #ifndef DBGERR
 542 #define DBGERR(fmt)
 543 #endif
 544 #ifndef DBGBH
 545 #define DBGBH(fmt)
 546 #endif
 547 #ifndef DBGISR
 548 #define DBGISR(fmt)
 549 #endif
 550
 551 #ifdef DBGDATA
 552 static void trace_block(struct slgt_info *info, const char *data, int count, const char *label)
 553 {
 554         int i;
 555         int linecount;
 556         printk("%s %s data:\n",info->device_name, label);
 557         while(count) {
 558                 linecount = (count > 16) ? 16 : count;
 559                 for(i=0; i < linecount; i++)
 560                         printk("%02X ",(unsigned char)data[i]);
 561                 for(;i<17;i++)
 562                         printk("   ");
 563                 for(i=0;i<linecount;i++) {
 564                         if (data[i]>=040 && data[i]<=0176)
 565                                 printk("%c",data[i]);
 566                         else
 567                                 printk(".");
 568                 }
 569                 printk("\n");
 570                 data  += linecount;
 571                 count -= linecount;
 572         }
 573 }
 574 #else
 575 #define DBGDATA(info, buf, size, label)
 576 #endif
 577
 578 #ifdef DBGTBUF
 579 static void dump_tbufs(struct slgt_info *info)
 580 {
 581         int i;
 582         printk("tbuf_current=%d\n", info->tbuf_current);
 583         for (i=0 ; i < info->tbuf_count ; i++) {
 584                 printk("%d: count=%04X status=%04X\n",
 585                         i, le16_to_cpu(info->tbufs[i].count), le16_to_cpu(info->tbufs[i].status));
 586         }
 587 }
 588 #else
 589 #define DBGTBUF(info)
 590 #endif
 591
 592 #ifdef DBGRBUF
 593 static void dump_rbufs(struct slgt_info *info)
 594 {
 595         int i;
 596         printk("rbuf_current=%d\n", info->rbuf_current);
 597         for (i=0 ; i < info->rbuf_count ; i++) {
 598                 printk("%d: count=%04X status=%04X\n",
 599                         i, le16_to_cpu(info->rbufs[i].count), le16_to_cpu(info->rbufs[i].status));
 600         }
 601 }
 602 #else
 603 #define DBGRBUF(info)
 604 #endif
 605
 606 static inline int sanity_check(struct slgt_info *info, char *devname, const char *name)
 607 {
 608 #ifdef SANITY_CHECK
 609         if (!info) {
 610                 printk("null struct slgt_info for (%s) in %s\n", devname, name);
 611                 return 1;
 612         }
 613         if (info->magic != MGSL_MAGIC) {
 614                 printk("bad magic number struct slgt_info (%s) in %s\n", devname, name);
 615                 return 1;
 616         }
 617 #else
 618         if (!info)
 619                 return 1;
 620 #endif
 621         return 0;
 622 }
 623
 624 /**
 625  * line discipline callback wrappers
 626  *
 627  * The wrappers maintain line discipline references
 628  * while calling into the line discipline.
 629  *
 630  * ldisc_receive_buf  - pass receive data to line discipline
 631  */
 632 static void ldisc_receive_buf(struct tty_struct *tty,
 633                               const __u8 *data, char *flags, int count)
 634 {
 635         struct tty_ldisc *ld;
 636         if (!tty)
 637                 return;
 638         ld = tty_ldisc_ref(tty);
 639         if (ld) {
 640                 if (ld->ops->receive_buf)
 641                         ld->ops->receive_buf(tty, data, flags, count);
 642                 tty_ldisc_deref(ld);
 643         }
 644 }
 645
 646 /* tty callbacks */
 647
 648 static int open(struct tty_struct *tty, struct file *filp)
 649 {
 650         struct slgt_info *info;
 651         int retval, line;
 652         unsigned long flags;
 653
 654         line = tty->index;
 655         if (line >= slgt_device_count) {
 656                 DBGERR(("%s: open with invalid line #%d.\n", driver_name, line));
 657                 return -ENODEV;
 658         }
 659
 660         info = slgt_device_list;
 661         while(info && info->line != line)
 662                 info = info->next_device;
 663         if (sanity_check(info, tty->name, "open"))
 664                 return -ENODEV;
 665         if (info->init_error) {
 666                 DBGERR(("%s init error=%d\n", info->device_name, info->init_error));
 667                 return -ENODEV;
 668         }
 669
 670         tty->driver_data = info;
 671         info->port.tty = tty;
 672
 673         DBGINFO(("%s open, old ref count = %d\n", info->device_name, info->port.count));
 674
 675         mutex_lock(&info->port.mutex);
 676         info->port.low_latency = (info->port.flags & ASYNC_LOW_LATENCY) ? 1 : 0;
 677
 678         spin_lock_irqsave(&info->netlock, flags);
 679         if (info->netcount) {
 680                 retval = -EBUSY;
 681                 spin_unlock_irqrestore(&info->netlock, flags);
 682                 mutex_unlock(&info->port.mutex);
 683                 goto cleanup;
 684         }
 685         info->port.count++;
 686         spin_unlock_irqrestore(&info->netlock, flags);
 687
 688         if (info->port.count == 1) {
 689                 /* 1st open on this device, init hardware */
 690                 retval = startup(info);
 691                 if (retval < 0) {
 692                         mutex_unlock(&info->port.mutex);
 693                         goto cleanup;
 694                 }
 695         }
 696         mutex_unlock(&info->port.mutex);
 697         retval = block_til_ready(tty, filp, info);
 698         if (retval) {
 699                 DBGINFO(("%s block_til_ready rc=%d\n", info->device_name, retval));
 700                 goto cleanup;
 701         }
 702
 703         retval = 0;
 704
 705 cleanup:
 706         if (retval) {
 707                 if (tty->count == 1)
 708                         info->port.tty = NULL; /* tty layer will release tty struct */
 709                 if(info->port.count)
 710                         info->port.count--;
 711         }
 712
 713         DBGINFO(("%s open rc=%d\n", info->device_name, retval));
 714         return retval;
 715 }
 716
 717 static void close(struct tty_struct *tty, struct file *filp)
 718 {
 719         struct slgt_info *info = tty->driver_data;
 720
 721         if (sanity_check(info, tty->name, "close"))
 722                 return;
 723         DBGINFO(("%s close entry, count=%d\n", info->device_name, info->port.count));
 724
 725         if (tty_port_close_start(&info->port, tty, filp) == 0)
 726                 goto cleanup;
 727
 728         mutex_lock(&info->port.mutex);
 729         if (tty_port_initialized(&info->port))
 730                 wait_until_sent(tty, info->timeout);
 731         flush_buffer(tty);
 732         tty_ldisc_flush(tty);
 733
 734         shutdown(info);
 735         mutex_unlock(&info->port.mutex);
 736
 737         tty_port_close_end(&info->port, tty);
 738         info->port.tty = NULL;
 739 cleanup:
 740         DBGINFO(("%s close exit, count=%d\n", tty->driver->name, info->port.count));
 741 }
 742
 743 static void hangup(struct tty_struct *tty)
 744 {
 745         struct slgt_info *info = tty->driver_data;
 746         unsigned long flags;
 747
 748         if (sanity_check(info, tty->name, "hangup"))
 749                 return;
 750         DBGINFO(("%s hangup\n", info->device_name));
 751
 752         flush_buffer(tty);
 753
 754         mutex_lock(&info->port.mutex);
 755         shutdown(info);
 756
 757         spin_lock_irqsave(&info->port.lock, flags);
 758         info->port.count = 0;
 759         info->port.tty = NULL;
 760         spin_unlock_irqrestore(&info->port.lock, flags);
 761         tty_port_set_active(&info->port, 0);
 762         mutex_unlock(&info->port.mutex);
 763
 764         wake_up_interruptible(&info->port.open_wait);
 765 }
 766
 767 static void set_termios(struct tty_struct *tty, struct ktermios *old_termios)
 768 {
 769         struct slgt_info *info = tty->driver_data;
 770         unsigned long flags;
 771
 772         DBGINFO(("%s set_termios\n", tty->driver->name));
 773
 774         change_params(info);
 775
 776         /* Handle transition to B0 status */
 777         if ((old_termios->c_cflag & CBAUD) && !C_BAUD(tty)) {
 778                 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
 779                 spin_lock_irqsave(&info->lock,flags);
 780                 set_signals(info);
 781                 spin_unlock_irqrestore(&info->lock,flags);
 782         }
 783
 784         /* Handle transition away from B0 status */
 785         if (!(old_termios->c_cflag & CBAUD) && C_BAUD(tty)) {
 786                 info->signals |= SerialSignal_DTR;
 787                 if (!C_CRTSCTS(tty) || !tty_throttled(tty))
 788                         info->signals |= SerialSignal_RTS;
 789                 spin_lock_irqsave(&info->lock,flags);
 790                 set_signals(info);
 791                 spin_unlock_irqrestore(&info->lock,flags);
 792         }
 793
 794         /* Handle turning off CRTSCTS */
 795         if ((old_termios->c_cflag & CRTSCTS) && !C_CRTSCTS(tty)) {
 796                 tty->hw_stopped = 0;
 797                 tx_release(tty);
 798         }
 799 }
 800
 801 static void update_tx_timer(struct slgt_info *info)
 802 {
 803         /*
 804          * use worst case speed of 1200bps to calculate transmit timeout
 805          * based on data in buffers (tbuf_bytes) and FIFO (128 bytes)
 806          */
 807         if (info->params.mode == MGSL_MODE_HDLC) {
 808                 int timeout  = (tbuf_bytes(info) * 7) + 1000;
 809                 mod_timer(&info->tx_timer, jiffies + msecs_to_jiffies(timeout));
 810         }
 811 }
 812
 813 static int write(struct tty_struct *tty,
 814                  const unsigned char *buf, int count)
 815 {
 816         int ret = 0;
 817         struct slgt_info *info = tty->driver_data;
 818         unsigned long flags;
 819
 820         if (sanity_check(info, tty->name, "write"))
 821                 return -EIO;
 822
 823         DBGINFO(("%s write count=%d\n", info->device_name, count));
 824
 825         if (!info->tx_buf || (count > info->max_frame_size))
 826                 return -EIO;
 827
 828         if (!count || tty->stopped || tty->hw_stopped)
 829                 return 0;
 830
 831         spin_lock_irqsave(&info->lock, flags);
 832
 833         if (info->tx_count) {
 834                 /* send accumulated data from send_char() */
 835                 if (!tx_load(info, info->tx_buf, info->tx_count))
 836                         goto cleanup;
 837                 info->tx_count = 0;
 838         }
 839
 840         if (tx_load(info, buf, count))
 841                 ret = count;
 842
 843 cleanup:
 844         spin_unlock_irqrestore(&info->lock, flags);
 845         DBGINFO(("%s write rc=%d\n", info->device_name, ret));
 846         return ret;
 847 }
 848
 849 static int put_char(struct tty_struct *tty, unsigned char ch)
 850 {
 851         struct slgt_info *info = tty->driver_data;
 852         unsigned long flags;
 853         int ret = 0;
 854
 855         if (sanity_check(info, tty->name, "put_char"))
 856                 return 0;
 857         DBGINFO(("%s put_char(%d)\n", info->device_name, ch));
 858         if (!info->tx_buf)
 859                 return 0;
 860         spin_lock_irqsave(&info->lock,flags);
 861         if (info->tx_count < info->max_frame_size) {
 862                 info->tx_buf[info->tx_count++] = ch;
 863                 ret = 1;
 864         }
 865         spin_unlock_irqrestore(&info->lock,flags);
 866         return ret;
 867 }
 868
 869 static void send_xchar(struct tty_struct *tty, char ch)
 870 {
 871         struct slgt_info *info = tty->driver_data;
 872         unsigned long flags;
 873
 874         if (sanity_check(info, tty->name, "send_xchar"))
 875                 return;
 876         DBGINFO(("%s send_xchar(%d)\n", info->device_name, ch));
 877         info->x_char = ch;
 878         if (ch) {
 879                 spin_lock_irqsave(&info->lock,flags);
 880                 if (!info->tx_enabled)
 881                         tx_start(info);
 882                 spin_unlock_irqrestore(&info->lock,flags);
 883         }
 884 }
 885
 886 static void wait_until_sent(struct tty_struct *tty, int timeout)
 887 {
 888         struct slgt_info *info = tty->driver_data;
 889         unsigned long orig_jiffies, char_time;
 890
 891         if (!info )
 892                 return;
 893         if (sanity_check(info, tty->name, "wait_until_sent"))
 894                 return;
 895         DBGINFO(("%s wait_until_sent entry\n", info->device_name));
 896         if (!tty_port_initialized(&info->port))
 897                 goto exit;
 898
 899         orig_jiffies = jiffies;
 900
 901         /* Set check interval to 1/5 of estimated time to
 902          * send a character, and make it at least 1. The check
 903          * interval should also be less than the timeout.
 904          * Note: use tight timings here to satisfy the NIST-PCTS.
 905          */
 906
 907         if (info->params.data_rate) {
 908                 char_time = info->timeout/(32 * 5);
 909                 if (!char_time)
 910                         char_time++;
 911         } else
 912                 char_time = 1;
 913
 914         if (timeout)
 915                 char_time = min_t(unsigned long, char_time, timeout);
 916
 917         while (info->tx_active) {
 918                 msleep_interruptible(jiffies_to_msecs(char_time));
 919                 if (signal_pending(current))
 920                         break;
 921                 if (timeout && time_after(jiffies, orig_jiffies + timeout))
 922                         break;
 923         }
 924 exit:
 925         DBGINFO(("%s wait_until_sent exit\n", info->device_name));
 926 }
 927
 928 static int write_room(struct tty_struct *tty)
 929 {
 930         struct slgt_info *info = tty->driver_data;
 931         int ret;
 932
 933         if (sanity_check(info, tty->name, "write_room"))
 934                 return 0;
 935         ret = (info->tx_active) ? 0 : HDLC_MAX_FRAME_SIZE;
 936         DBGINFO(("%s write_room=%d\n", info->device_name, ret));
 937         return ret;
 938 }
 939
 940 static void flush_chars(struct tty_struct *tty)
 941 {
 942         struct slgt_info *info = tty->driver_data;
 943         unsigned long flags;
 944
 945         if (sanity_check(info, tty->name, "flush_chars"))
 946                 return;
 947         DBGINFO(("%s flush_chars entry tx_count=%d\n", info->device_name, info->tx_count));
 948
 949         if (info->tx_count <= 0 || tty->stopped ||
 950             tty->hw_stopped || !info->tx_buf)
 951                 return;
 952
 953         DBGINFO(("%s flush_chars start transmit\n", info->device_name));
 954
 955         spin_lock_irqsave(&info->lock,flags);
 956         if (info->tx_count && tx_load(info, info->tx_buf, info->tx_count))
 957                 info->tx_count = 0;
 958         spin_unlock_irqrestore(&info->lock,flags);
 959 }
 960
 961 static void flush_buffer(struct tty_struct *tty)
 962 {
 963         struct slgt_info *info = tty->driver_data;
 964         unsigned long flags;
 965
 966         if (sanity_check(info, tty->name, "flush_buffer"))
 967                 return;
 968         DBGINFO(("%s flush_buffer\n", info->device_name));
 969
 970         spin_lock_irqsave(&info->lock, flags);
 971         info->tx_count = 0;
 972         spin_unlock_irqrestore(&info->lock, flags);
 973
 974         tty_wakeup(tty);
 975 }
 976
 977 /*
 978  * throttle (stop) transmitter
 979  */
 980 static void tx_hold(struct tty_struct *tty)
 981 {
 982         struct slgt_info *info = tty->driver_data;
 983         unsigned long flags;
 984
 985         if (sanity_check(info, tty->name, "tx_hold"))
 986                 return;
 987         DBGINFO(("%s tx_hold\n", info->device_name));
 988         spin_lock_irqsave(&info->lock,flags);
 989         if (info->tx_enabled && info->params.mode == MGSL_MODE_ASYNC)
 990                 tx_stop(info);
 991         spin_unlock_irqrestore(&info->lock,flags);
 992 }
 993
 994 /*
 995  * release (start) transmitter
 996  */
 997 static void tx_release(struct tty_struct *tty)
 998 {
 999         struct slgt_info *info = tty->driver_data;
1000         unsigned long flags;
1001
1002         if (sanity_check(info, tty->name, "tx_release"))
1003                 return;
1004         DBGINFO(("%s tx_release\n", info->device_name));
1005         spin_lock_irqsave(&info->lock, flags);
1006         if (info->tx_count && tx_load(info, info->tx_buf, info->tx_count))
1007                 info->tx_count = 0;
1008         spin_unlock_irqrestore(&info->lock, flags);
1009 }
1010
1011 /*
1012  * Service an IOCTL request
1013  *
1014  * Arguments
1015  *
1016  *      tty     pointer to tty instance data
1017  *      cmd     IOCTL command code
1018  *      arg     command argument/context
1019  *
1020  * Return 0 if success, otherwise error code
1021  */
1022 static int ioctl(struct tty_struct *tty,
1023                  unsigned int cmd, unsigned long arg)
1024 {
1025         struct slgt_info *info = tty->driver_data;
1026         void __user *argp = (void __user *)arg;
1027         int ret;
1028
1029         if (sanity_check(info, tty->name, "ioctl"))
1030                 return -ENODEV;
1031         DBGINFO(("%s ioctl() cmd=%08X\n", info->device_name, cmd));
1032
1033         if ((cmd != TIOCGSERIAL) && (cmd != TIOCSSERIAL) &&
1034             (cmd != TIOCMIWAIT)) {
1035                 if (tty_io_error(tty))
1036                     return -EIO;
1037         }
1038
1039         switch (cmd) {
1040         case MGSL_IOCWAITEVENT:
1041                 return wait_mgsl_event(info, argp);
1042         case TIOCMIWAIT:
1043                 return modem_input_wait(info,(int)arg);
1044         case MGSL_IOCSGPIO:
1045                 return set_gpio(info, argp);
1046         case MGSL_IOCGGPIO:
1047                 return get_gpio(info, argp);
1048         case MGSL_IOCWAITGPIO:
1049                 return wait_gpio(info, argp);
1050         case MGSL_IOCGXSYNC:
1051                 return get_xsync(info, argp);
1052         case MGSL_IOCSXSYNC:
1053                 return set_xsync(info, (int)arg);
1054         case MGSL_IOCGXCTRL:
1055                 return get_xctrl(info, argp);
1056         case MGSL_IOCSXCTRL:
1057                 return set_xctrl(info, (int)arg);
1058         }
1059         mutex_lock(&info->port.mutex);
1060         switch (cmd) {
1061         case MGSL_IOCGPARAMS:
1062                 ret = get_params(info, argp);
1063                 break;
1064         case MGSL_IOCSPARAMS:
1065                 ret = set_params(info, argp);
1066                 break;
1067         case MGSL_IOCGTXIDLE:
1068                 ret = get_txidle(info, argp);
1069                 break;
1070         case MGSL_IOCSTXIDLE:
1071                 ret = set_txidle(info, (int)arg);
1072                 break;
1073         case MGSL_IOCTXENABLE:
1074                 ret = tx_enable(info, (int)arg);
1075                 break;
1076         case MGSL_IOCRXENABLE:
1077                 ret = rx_enable(info, (int)arg);
1078                 break;
1079         case MGSL_IOCTXABORT:
1080                 ret = tx_abort(info);
1081                 break;
1082         case MGSL_IOCGSTATS:
1083                 ret = get_stats(info, argp);
1084                 break;
1085         case MGSL_IOCGIF:
1086                 ret = get_interface(info, argp);
1087                 break;
1088         case MGSL_IOCSIF:
1089                 ret = set_interface(info,(int)arg);
1090                 break;
1091         default:
1092                 ret = -ENOIOCTLCMD;
1093         }
1094         mutex_unlock(&info->port.mutex);
1095         return ret;
1096 }
1097
1098 static int get_icount(struct tty_struct *tty,
1099                                 struct serial_icounter_struct *icount)
1100
1101 {
1102         struct slgt_info *info = tty->driver_data;
1103         struct mgsl_icount cnow;        /* kernel counter temps */
1104         unsigned long flags;
1105
1106         spin_lock_irqsave(&info->lock,flags);
1107         cnow = info->icount;
1108         spin_unlock_irqrestore(&info->lock,flags);
1109
1110         icount->cts = cnow.cts;
1111         icount->dsr = cnow.dsr;
1112         icount->rng = cnow.rng;
1113         icount->dcd = cnow.dcd;
1114         icount->rx = cnow.rx;
1115         icount->tx = cnow.tx;
1116         icount->frame = cnow.frame;
1117         icount->overrun = cnow.overrun;
1118         icount->parity = cnow.parity;
1119         icount->brk = cnow.brk;
1120         icount->buf_overrun = cnow.buf_overrun;
1121
1122         return 0;
1123 }
1124
1125 /*
1126  * support for 32 bit ioctl calls on 64 bit systems
1127  */
1128 #ifdef CONFIG_COMPAT
1129 static long get_params32(struct slgt_info *info, struct MGSL_PARAMS32 __user *user_params)
1130 {
1131         struct MGSL_PARAMS32 tmp_params;
1132
1133         DBGINFO(("%s get_params32\n", info->device_name));
1134         memset(&tmp_params, 0, sizeof(tmp_params));
1135         tmp_params.mode            = (compat_ulong_t)info->params.mode;
1136         tmp_params.loopback        = info->params.loopback;
1137         tmp_params.flags           = info->params.flags;
1138         tmp_params.encoding        = info->params.encoding;
1139         tmp_params.clock_speed     = (compat_ulong_t)info->params.clock_speed;
1140         tmp_params.addr_filter     = info->params.addr_filter;
1141         tmp_params.crc_type        = info->params.crc_type;
1142         tmp_params.preamble_length = info->params.preamble_length;
1143         tmp_params.preamble        = info->params.preamble;
1144         tmp_params.data_rate       = (compat_ulong_t)info->params.data_rate;
1145         tmp_params.data_bits       = info->params.data_bits;
1146         tmp_params.stop_bits       = info->params.stop_bits;
1147         tmp_params.parity          = info->params.parity;
1148         if (copy_to_user(user_params, &tmp_params, sizeof(struct MGSL_PARAMS32)))
1149                 return -EFAULT;
1150         return 0;
1151 }
1152
1153 static long set_params32(struct slgt_info *info, struct MGSL_PARAMS32 __user *new_params)
1154 {
1155         struct MGSL_PARAMS32 tmp_params;
1156
1157         DBGINFO(("%s set_params32\n", info->device_name));
1158         if (copy_from_user(&tmp_params, new_params, sizeof(struct MGSL_PARAMS32)))
1159                 return -EFAULT;
1160
1161         spin_lock(&info->lock);
1162         if (tmp_params.mode == MGSL_MODE_BASE_CLOCK) {
1163                 info->base_clock = tmp_params.clock_speed;
1164         } else {
1165                 info->params.mode            = tmp_params.mode;
1166                 info->params.loopback        = tmp_params.loopback;
1167                 info->params.flags           = tmp_params.flags;
1168                 info->params.encoding        = tmp_params.encoding;
1169                 info->params.clock_speed     = tmp_params.clock_speed;
1170                 info->params.addr_filter     = tmp_params.addr_filter;
1171                 info->params.crc_type        = tmp_params.crc_type;
1172                 info->params.preamble_length = tmp_params.preamble_length;
1173                 info->params.preamble        = tmp_params.preamble;
1174                 info->params.data_rate       = tmp_params.data_rate;
1175                 info->params.data_bits       = tmp_params.data_bits;
1176                 info->params.stop_bits       = tmp_params.stop_bits;
1177                 info->params.parity          = tmp_params.parity;
1178         }
1179         spin_unlock(&info->lock);
1180
1181         program_hw(info);
1182
1183         return 0;
1184 }
1185
1186 static long slgt_compat_ioctl(struct tty_struct *tty,
1187                          unsigned int cmd, unsigned long arg)
1188 {
1189         struct slgt_info *info = tty->driver_data;
1190         int rc;
1191
1192         if (sanity_check(info, tty->name, "compat_ioctl"))
1193                 return -ENODEV;
1194         DBGINFO(("%s compat_ioctl() cmd=%08X\n", info->device_name, cmd));
1195
1196         switch (cmd) {
1197         case MGSL_IOCSPARAMS32:
1198                 rc = set_params32(info, compat_ptr(arg));
1199                 break;
1200
1201         case MGSL_IOCGPARAMS32:
1202                 rc = get_params32(info, compat_ptr(arg));
1203                 break;
1204
1205         case MGSL_IOCGPARAMS:
1206         case MGSL_IOCSPARAMS:
1207         case MGSL_IOCGTXIDLE:
1208         case MGSL_IOCGSTATS:
1209         case MGSL_IOCWAITEVENT:
1210         case MGSL_IOCGIF:
1211         case MGSL_IOCSGPIO:
1212         case MGSL_IOCGGPIO:
1213         case MGSL_IOCWAITGPIO:
1214         case MGSL_IOCGXSYNC:
1215         case MGSL_IOCGXCTRL:
1216                 rc = ioctl(tty, cmd, (unsigned long)compat_ptr(arg));
1217                 break;
1218         default:
1219                 rc = ioctl(tty, cmd, arg);
1220         }
1221         DBGINFO(("%s compat_ioctl() cmd=%08X rc=%d\n", info->device_name, cmd, rc));
1222         return rc;
1223 }
1224 #else
1225 #define slgt_compat_ioctl NULL
1226 #endif /* ifdef CONFIG_COMPAT */
1227
1228 /*
1229  * proc fs support
1230  */
1231 static inline void line_info(struct seq_file *m, struct slgt_info *info)
1232 {
1233         char stat_buf[30];
1234         unsigned long flags;
1235
1236         seq_printf(m, "%s: IO=%08X IRQ=%d MaxFrameSize=%u\n",
1237                       info->device_name, info->phys_reg_addr,
1238                       info->irq_level, info->max_frame_size);
1239
1240         /* output current serial signal states */
1241         spin_lock_irqsave(&info->lock,flags);
1242         get_signals(info);
1243         spin_unlock_irqrestore(&info->lock,flags);
1244
1245         stat_buf[0] = 0;
1246         stat_buf[1] = 0;
1247         if (info->signals & SerialSignal_RTS)
1248                 strcat(stat_buf, "|RTS");
1249         if (info->signals & SerialSignal_CTS)
1250                 strcat(stat_buf, "|CTS");
1251         if (info->signals & SerialSignal_DTR)
1252                 strcat(stat_buf, "|DTR");
1253         if (info->signals & SerialSignal_DSR)
1254                 strcat(stat_buf, "|DSR");
1255         if (info->signals & SerialSignal_DCD)
1256                 strcat(stat_buf, "|CD");
1257         if (info->signals & SerialSignal_RI)
1258                 strcat(stat_buf, "|RI");
1259
1260         if (info->params.mode != MGSL_MODE_ASYNC) {
1261                 seq_printf(m, "\tHDLC txok:%d rxok:%d",
1262                                info->icount.txok, info->icount.rxok);
1263                 if (info->icount.txunder)
1264                         seq_printf(m, " txunder:%d", info->icount.txunder);
1265                 if (info->icount.txabort)
1266                         seq_printf(m, " txabort:%d", info->icount.txabort);
1267                 if (info->icount.rxshort)
1268                         seq_printf(m, " rxshort:%d", info->icount.rxshort);
1269                 if (info->icount.rxlong)
1270                         seq_printf(m, " rxlong:%d", info->icount.rxlong);
1271                 if (info->icount.rxover)
1272                         seq_printf(m, " rxover:%d", info->icount.rxover);
1273                 if (info->icount.rxcrc)
1274                         seq_printf(m, " rxcrc:%d", info->icount.rxcrc);
1275         } else {
1276                 seq_printf(m, "\tASYNC tx:%d rx:%d",
1277                                info->icount.tx, info->icount.rx);
1278                 if (info->icount.frame)
1279                         seq_printf(m, " fe:%d", info->icount.frame);
1280                 if (info->icount.parity)
1281                         seq_printf(m, " pe:%d", info->icount.parity);
1282                 if (info->icount.brk)
1283                         seq_printf(m, " brk:%d", info->icount.brk);
1284                 if (info->icount.overrun)
1285                         seq_printf(m, " oe:%d", info->icount.overrun);
1286         }
1287
1288         /* Append serial signal status to end */
1289         seq_printf(m, " %s\n", stat_buf+1);
1290
1291         seq_printf(m, "\ttxactive=%d bh_req=%d bh_run=%d pending_bh=%x\n",
1292                        info->tx_active,info->bh_requested,info->bh_running,
1293                        info->pending_bh);
1294 }
1295
1296 /* Called to print information about devices
1297  */
1298 static int synclink_gt_proc_show(struct seq_file *m, void *v)
1299 {
1300         struct slgt_info *info;
1301
1302         seq_puts(m, "synclink_gt driver\n");
1303
1304         info = slgt_device_list;
1305         while( info ) {
1306                 line_info(m, info);
1307                 info = info->next_device;
1308         }
1309         return 0;
1310 }
1311
1312 static int synclink_gt_proc_open(struct inode *inode, struct file *file)
1313 {
1314         return single_open(file, synclink_gt_proc_show, NULL);
1315 }
1316
1317 static const struct file_operations synclink_gt_proc_fops = {
1318         .owner          = THIS_MODULE,
1319         .open           = synclink_gt_proc_open,
1320         .read           = seq_read,
1321         .llseek         = seq_lseek,
1322         .release        = single_release,
1323 };
1324
1325 /*
1326  * return count of bytes in transmit buffer
1327  */
1328 static int chars_in_buffer(struct tty_struct *tty)
1329 {
1330         struct slgt_info *info = tty->driver_data;
1331         int count;
1332         if (sanity_check(info, tty->name, "chars_in_buffer"))
1333                 return 0;
1334         count = tbuf_bytes(info);
1335         DBGINFO(("%s chars_in_buffer()=%d\n", info->device_name, count));
1336         return count;
1337 }
1338
1339 /*
1340  * signal remote device to throttle send data (our receive data)
1341  */
1342 static void throttle(struct tty_struct * tty)
1343 {
1344         struct slgt_info *info = tty->driver_data;
1345         unsigned long flags;
1346
1347         if (sanity_check(info, tty->name, "throttle"))
1348                 return;
1349         DBGINFO(("%s throttle\n", info->device_name));
1350         if (I_IXOFF(tty))
1351                 send_xchar(tty, STOP_CHAR(tty));
1352         if (C_CRTSCTS(tty)) {
1353                 spin_lock_irqsave(&info->lock,flags);
1354                 info->signals &= ~SerialSignal_RTS;
1355                 set_signals(info);
1356                 spin_unlock_irqrestore(&info->lock,flags);
1357         }
1358 }
1359
1360 /*
1361  * signal remote device to stop throttling send data (our receive data)
1362  */
1363 static void unthrottle(struct tty_struct * tty)
1364 {
1365         struct slgt_info *info = tty->driver_data;
1366         unsigned long flags;
1367
1368         if (sanity_check(info, tty->name, "unthrottle"))
1369                 return;
1370         DBGINFO(("%s unthrottle\n", info->device_name));
1371         if (I_IXOFF(tty)) {
1372                 if (info->x_char)
1373                         info->x_char = 0;
1374                 else
1375                         send_xchar(tty, START_CHAR(tty));
1376         }
1377         if (C_CRTSCTS(tty)) {
1378                 spin_lock_irqsave(&info->lock,flags);
1379                 info->signals |= SerialSignal_RTS;
1380                 set_signals(info);
1381                 spin_unlock_irqrestore(&info->lock,flags);
1382         }
1383 }
1384
1385 /*
1386  * set or clear transmit break condition
1387  * break_state  -1=set break condition, 0=clear
1388  */
1389 static int set_break(struct tty_struct *tty, int break_state)
1390 {
1391         struct slgt_info *info = tty->driver_data;
1392         unsigned short value;
1393         unsigned long flags;
1394
1395         if (sanity_check(info, tty->name, "set_break"))
1396                 return -EINVAL;
1397         DBGINFO(("%s set_break(%d)\n", info->device_name, break_state));
1398
1399         spin_lock_irqsave(&info->lock,flags);
1400         value = rd_reg16(info, TCR);
1401         if (break_state == -1)
1402                 value |= BIT6;
1403         else
1404                 value &= ~BIT6;
1405         wr_reg16(info, TCR, value);
1406         spin_unlock_irqrestore(&info->lock,flags);
1407         return 0;
1408 }
1409
1410 #if SYNCLINK_GENERIC_HDLC
1411
1412 /**
1413  * called by generic HDLC layer when protocol selected (PPP, frame relay, etc.)
1414  * set encoding and frame check sequence (FCS) options
1415  *
1416  * dev       pointer to network device structure
1417  * encoding  serial encoding setting
1418  * parity    FCS setting
1419  *
1420  * returns 0 if success, otherwise error code
1421  */
1422 static int hdlcdev_attach(struct net_device *dev, unsigned short encoding,
1423                           unsigned short parity)
1424 {
1425         struct slgt_info *info = dev_to_port(dev);
1426         unsigned char  new_encoding;
1427         unsigned short new_crctype;
1428
1429         /* return error if TTY interface open */
1430         if (info->port.count)
1431                 return -EBUSY;
1432
1433         DBGINFO(("%s hdlcdev_attach\n", info->device_name));
1434
1435         switch (encoding)
1436         {
1437         case ENCODING_NRZ:        new_encoding = HDLC_ENCODING_NRZ; break;
1438         case ENCODING_NRZI:       new_encoding = HDLC_ENCODING_NRZI_SPACE; break;
1439         case ENCODING_FM_MARK:    new_encoding = HDLC_ENCODING_BIPHASE_MARK; break;
1440         case ENCODING_FM_SPACE:   new_encoding = HDLC_ENCODING_BIPHASE_SPACE; break;
1441         case ENCODING_MANCHESTER: new_encoding = HDLC_ENCODING_BIPHASE_LEVEL; break;
1442         default: return -EINVAL;
1443         }
1444
1445         switch (parity)
1446         {
1447         case PARITY_NONE:            new_crctype = HDLC_CRC_NONE; break;
1448         case PARITY_CRC16_PR1_CCITT: new_crctype = HDLC_CRC_16_CCITT; break;
1449         case PARITY_CRC32_PR1_CCITT: new_crctype = HDLC_CRC_32_CCITT; break;
1450         default: return -EINVAL;
1451         }
1452
1453         info->params.encoding = new_encoding;
1454         info->params.crc_type = new_crctype;
1455
1456         /* if network interface up, reprogram hardware */
1457         if (info->netcount)
1458                 program_hw(info);
1459
1460         return 0;
1461 }
1462
1463 /**
1464  * called by generic HDLC layer to send frame
1465  *
1466  * skb  socket buffer containing HDLC frame
1467  * dev  pointer to network device structure
1468  */
1469 static netdev_tx_t hdlcdev_xmit(struct sk_buff *skb,
1470                                       struct net_device *dev)
1471 {
1472         struct slgt_info *info = dev_to_port(dev);
1473         unsigned long flags;
1474
1475         DBGINFO(("%s hdlc_xmit\n", dev->name));
1476
1477         if (!skb->len)
1478                 return NETDEV_TX_OK;
1479
1480         /* stop sending until this frame completes */
1481         netif_stop_queue(dev);
1482
1483         /* update network statistics */
1484         dev->stats.tx_packets++;
1485         dev->stats.tx_bytes += skb->len;
1486
1487         /* save start time for transmit timeout detection */
1488         netif_trans_update(dev);
1489
1490         spin_lock_irqsave(&info->lock, flags);
1491         tx_load(info, skb->data, skb->len);
1492         spin_unlock_irqrestore(&info->lock, flags);
1493
1494         /* done with socket buffer, so free it */
1495         dev_kfree_skb(skb);
1496
1497         return NETDEV_TX_OK;
1498 }
1499
1500 /**
1501  * called by network layer when interface enabled
1502  * claim resources and initialize hardware
1503  *
1504  * dev  pointer to network device structure
1505  *
1506  * returns 0 if success, otherwise error code
1507  */
1508 static int hdlcdev_open(struct net_device *dev)
1509 {
1510         struct slgt_info *info = dev_to_port(dev);
1511         int rc;
1512         unsigned long flags;
1513
1514         if (!try_module_get(THIS_MODULE))
1515                 return -EBUSY;
1516
1517         DBGINFO(("%s hdlcdev_open\n", dev->name));
1518
1519         /* generic HDLC layer open processing */
1520         rc = hdlc_open(dev);
1521         if (rc)
1522                 return rc;
1523
1524         /* arbitrate between network and tty opens */
1525         spin_lock_irqsave(&info->netlock, flags);
1526         if (info->port.count != 0 || info->netcount != 0) {
1527                 DBGINFO(("%s hdlc_open busy\n", dev->name));
1528                 spin_unlock_irqrestore(&info->netlock, flags);
1529                 return -EBUSY;
1530         }
1531         info->netcount=1;
1532         spin_unlock_irqrestore(&info->netlock, flags);
1533
1534         /* claim resources and init adapter */
1535         if ((rc = startup(info)) != 0) {
1536                 spin_lock_irqsave(&info->netlock, flags);
1537                 info->netcount=0;
1538                 spin_unlock_irqrestore(&info->netlock, flags);
1539                 return rc;
1540         }
1541
1542         /* assert RTS and DTR, apply hardware settings */
1543         info->signals |= SerialSignal_RTS | SerialSignal_DTR;
1544         program_hw(info);
1545
1546         /* enable network layer transmit */
1547         netif_trans_update(dev);
1548         netif_start_queue(dev);
1549
1550         /* inform generic HDLC layer of current DCD status */
1551         spin_lock_irqsave(&info->lock, flags);
1552         get_signals(info);
1553         spin_unlock_irqrestore(&info->lock, flags);
1554         if (info->signals & SerialSignal_DCD)
1555                 netif_carrier_on(dev);
1556         else
1557                 netif_carrier_off(dev);
1558         return 0;
1559 }
1560
1561 /**
1562  * called by network layer when interface is disabled
1563  * shutdown hardware and release resources
1564  *
1565  * dev  pointer to network device structure
1566  *
1567  * returns 0 if success, otherwise error code
1568  */
1569 static int hdlcdev_close(struct net_device *dev)
1570 {
1571         struct slgt_info *info = dev_to_port(dev);
1572         unsigned long flags;
1573
1574         DBGINFO(("%s hdlcdev_close\n", dev->name));
1575
1576         netif_stop_queue(dev);
1577
1578         /* shutdown adapter and release resources */
1579         shutdown(info);
1580
1581         hdlc_close(dev);
1582
1583         spin_lock_irqsave(&info->netlock, flags);
1584         info->netcount=0;
1585         spin_unlock_irqrestore(&info->netlock, flags);
1586
1587         module_put(THIS_MODULE);
1588         return 0;
1589 }
1590
1591 /**
1592  * called by network layer to process IOCTL call to network device
1593  *
1594  * dev  pointer to network device structure
1595  * ifr  pointer to network interface request structure
1596  * cmd  IOCTL command code
1597  *
1598  * returns 0 if success, otherwise error code
1599  */
1600 static int hdlcdev_ioctl(struct net_device *dev, struct ifreq *ifr, int cmd)
1601 {
1602         const size_t size = sizeof(sync_serial_settings);
1603         sync_serial_settings new_line;
1604         sync_serial_settings __user *line = ifr->ifr_settings.ifs_ifsu.sync;
1605         struct slgt_info *info = dev_to_port(dev);
1606         unsigned int flags;
1607
1608         DBGINFO(("%s hdlcdev_ioctl\n", dev->name));
1609
1610         /* return error if TTY interface open */
1611         if (info->port.count)
1612                 return -EBUSY;
1613
1614         if (cmd != SIOCWANDEV)
1615                 return hdlc_ioctl(dev, ifr, cmd);
1616
1617         memset(&new_line, 0, sizeof(new_line));
1618
1619         switch(ifr->ifr_settings.type) {
1620         case IF_GET_IFACE: /* return current sync_serial_settings */
1621
1622                 ifr->ifr_settings.type = IF_IFACE_SYNC_SERIAL;
1623                 if (ifr->ifr_settings.size < size) {
1624                         ifr->ifr_settings.size = size; /* data size wanted */
1625                         return -ENOBUFS;
1626                 }
1627
1628                 flags = info->params.flags & (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1629                                               HDLC_FLAG_RXC_BRG    | HDLC_FLAG_RXC_TXCPIN |
1630                                               HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1631                                               HDLC_FLAG_TXC_BRG    | HDLC_FLAG_TXC_RXCPIN);
1632
1633                 switch (flags){
1634                 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN): new_line.clock_type = CLOCK_EXT; break;
1635                 case (HDLC_FLAG_RXC_BRG    | HDLC_FLAG_TXC_BRG):    new_line.clock_type = CLOCK_INT; break;
1636                 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG):    new_line.clock_type = CLOCK_TXINT; break;
1637                 case (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN): new_line.clock_type = CLOCK_TXFROMRX; break;
1638                 default: new_line.clock_type = CLOCK_DEFAULT;
1639                 }
1640
1641                 new_line.clock_rate = info->params.clock_speed;
1642                 new_line.loopback   = info->params.loopback ? 1:0;
1643
1644                 if (copy_to_user(line, &new_line, size))
1645                         return -EFAULT;
1646                 return 0;
1647
1648         case IF_IFACE_SYNC_SERIAL: /* set sync_serial_settings */
1649
1650                 if(!capable(CAP_NET_ADMIN))
1651                         return -EPERM;
1652                 if (copy_from_user(&new_line, line, size))
1653                         return -EFAULT;
1654
1655                 switch (new_line.clock_type)
1656                 {
1657                 case CLOCK_EXT:      flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_TXCPIN; break;
1658                 case CLOCK_TXFROMRX: flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_RXCPIN; break;
1659                 case CLOCK_INT:      flags = HDLC_FLAG_RXC_BRG    | HDLC_FLAG_TXC_BRG;    break;
1660                 case CLOCK_TXINT:    flags = HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_TXC_BRG;    break;
1661                 case CLOCK_DEFAULT:  flags = info->params.flags &
1662                                              (HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1663                                               HDLC_FLAG_RXC_BRG    | HDLC_FLAG_RXC_TXCPIN |
1664                                               HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1665                                               HDLC_FLAG_TXC_BRG    | HDLC_FLAG_TXC_RXCPIN); break;
1666                 default: return -EINVAL;
1667                 }
1668
1669                 if (new_line.loopback != 0 && new_line.loopback != 1)
1670                         return -EINVAL;
1671
1672                 info->params.flags &= ~(HDLC_FLAG_RXC_RXCPIN | HDLC_FLAG_RXC_DPLL |
1673                                         HDLC_FLAG_RXC_BRG    | HDLC_FLAG_RXC_TXCPIN |
1674                                         HDLC_FLAG_TXC_TXCPIN | HDLC_FLAG_TXC_DPLL |
1675                                         HDLC_FLAG_TXC_BRG    | HDLC_FLAG_TXC_RXCPIN);
1676                 info->params.flags |= flags;
1677
1678                 info->params.loopback = new_line.loopback;
1679
1680                 if (flags & (HDLC_FLAG_RXC_BRG | HDLC_FLAG_TXC_BRG))
1681                         info->params.clock_speed = new_line.clock_rate;
1682                 else
1683                         info->params.clock_speed = 0;
1684
1685                 /* if network interface up, reprogram hardware */
1686                 if (info->netcount)
1687                         program_hw(info);
1688                 return 0;
1689
1690         default:
1691                 return hdlc_ioctl(dev, ifr, cmd);
1692         }
1693 }
1694
1695 /**
1696  * called by network layer when transmit timeout is detected
1697  *
1698  * dev  pointer to network device structure
1699  */
1700 static void hdlcdev_tx_timeout(struct net_device *dev)
1701 {
1702         struct slgt_info *info = dev_to_port(dev);
1703         unsigned long flags;
1704
1705         DBGINFO(("%s hdlcdev_tx_timeout\n", dev->name));
1706
1707         dev->stats.tx_errors++;
1708         dev->stats.tx_aborted_errors++;
1709
1710         spin_lock_irqsave(&info->lock,flags);
1711         tx_stop(info);
1712         spin_unlock_irqrestore(&info->lock,flags);
1713
1714         netif_wake_queue(dev);
1715 }
1716
1717 /**
1718  * called by device driver when transmit completes
1719  * reenable network layer transmit if stopped
1720  *
1721  * info  pointer to device instance information
1722  */
1723 static void hdlcdev_tx_done(struct slgt_info *info)
1724 {
1725         if (netif_queue_stopped(info->netdev))
1726                 netif_wake_queue(info->netdev);
1727 }
1728
1729 /**
1730  * called by device driver when frame received
1731  * pass frame to network layer
1732  *
1733  * info  pointer to device instance information
1734  * buf   pointer to buffer contianing frame data
1735  * size  count of data bytes in buf
1736  */
1737 static void hdlcdev_rx(struct slgt_info *info, char *buf, int size)
1738 {
1739         struct sk_buff *skb = dev_alloc_skb(size);
1740         struct net_device *dev = info->netdev;
1741
1742         DBGINFO(("%s hdlcdev_rx\n", dev->name));
1743
1744         if (skb == NULL) {
1745                 DBGERR(("%s: can't alloc skb, drop packet\n", dev->name));
1746                 dev->stats.rx_dropped++;
1747                 return;
1748         }
1749
1750         skb_put_data(skb, buf, size);
1751
1752         skb->protocol = hdlc_type_trans(skb, dev);
1753
1754         dev->stats.rx_packets++;
1755         dev->stats.rx_bytes += size;
1756
1757         netif_rx(skb);
1758 }
1759
1760 static const struct net_device_ops hdlcdev_ops = {
1761         .ndo_open       = hdlcdev_open,
1762         .ndo_stop       = hdlcdev_close,
1763         .ndo_start_xmit = hdlc_start_xmit,
1764         .ndo_do_ioctl   = hdlcdev_ioctl,
1765         .ndo_tx_timeout = hdlcdev_tx_timeout,
1766 };
1767
1768 /**
1769  * called by device driver when adding device instance
1770  * do generic HDLC initialization
1771  *
1772  * info  pointer to device instance information
1773  *
1774  * returns 0 if success, otherwise error code
1775  */
1776 static int hdlcdev_init(struct slgt_info *info)
1777 {
1778         int rc;
1779         struct net_device *dev;
1780         hdlc_device *hdlc;
1781
1782         /* allocate and initialize network and HDLC layer objects */
1783
1784         dev = alloc_hdlcdev(info);
1785         if (!dev) {
1786                 printk(KERN_ERR "%s hdlc device alloc failure\n", info->device_name);
1787                 return -ENOMEM;
1788         }
1789
1790         /* for network layer reporting purposes only */
1791         dev->mem_start = info->phys_reg_addr;
1792         dev->mem_end   = info->phys_reg_addr + SLGT_REG_SIZE - 1;
1793         dev->irq       = info->irq_level;
1794
1795         /* network layer callbacks and settings */
1796         dev->netdev_ops     = &hdlcdev_ops;
1797         dev->watchdog_timeo = 10 * HZ;
1798         dev->tx_queue_len   = 50;
1799
1800         /* generic HDLC layer callbacks and settings */
1801         hdlc         = dev_to_hdlc(dev);
1802         hdlc->attach = hdlcdev_attach;
1803         hdlc->xmit   = hdlcdev_xmit;
1804
1805         /* register objects with HDLC layer */
1806         rc = register_hdlc_device(dev);
1807         if (rc) {
1808                 printk(KERN_WARNING "%s:unable to register hdlc device\n",__FILE__);
1809                 free_netdev(dev);
1810                 return rc;
1811         }
1812
1813         info->netdev = dev;
1814         return 0;
1815 }
1816
1817 /**
1818  * called by device driver when removing device instance
1819  * do generic HDLC cleanup
1820  *
1821  * info  pointer to device instance information
1822  */
1823 static void hdlcdev_exit(struct slgt_info *info)
1824 {
1825         unregister_hdlc_device(info->netdev);
1826         free_netdev(info->netdev);
1827         info->netdev = NULL;
1828 }
1829
1830 #endif /* ifdef CONFIG_HDLC */
1831
1832 /*
1833  * get async data from rx DMA buffers
1834  */
1835 static void rx_async(struct slgt_info *info)
1836 {
1837         struct mgsl_icount *icount = &info->icount;
1838         unsigned int start, end;
1839         unsigned char *p;
1840         unsigned char status;
1841         struct slgt_desc *bufs = info->rbufs;
1842         int i, count;
1843         int chars = 0;
1844         int stat;
1845         unsigned char ch;
1846
1847         start = end = info->rbuf_current;
1848
1849         while(desc_complete(bufs[end])) {
1850                 count = desc_count(bufs[end]) - info->rbuf_index;
1851                 p     = bufs[end].buf + info->rbuf_index;
1852
1853                 DBGISR(("%s rx_async count=%d\n", info->device_name, count));
1854                 DBGDATA(info, p, count, "rx");
1855
1856                 for(i=0 ; i < count; i+=2, p+=2) {
1857                         ch = *p;
1858                         icount->rx++;
1859
1860                         stat = 0;
1861
1862                         status = *(p + 1) & (BIT1 + BIT0);
1863                         if (status) {
1864                                 if (status & BIT1)
1865                                         icount->parity++;
1866                                 else if (status & BIT0)
1867                                         icount->frame++;
1868                                 /* discard char if tty control flags say so */
1869                                 if (status & info->ignore_status_mask)
1870                                         continue;
1871                                 if (status & BIT1)
1872                                         stat = TTY_PARITY;
1873                                 else if (status & BIT0)
1874                                         stat = TTY_FRAME;
1875                         }
1876                         tty_insert_flip_char(&info->port, ch, stat);
1877                         chars++;
1878                 }
1879
1880                 if (i < count) {
1881                         /* receive buffer not completed */
1882                         info->rbuf_index += i;
1883                         mod_timer(&info->rx_timer, jiffies + 1);
1884                         break;
1885                 }
1886
1887                 info->rbuf_index = 0;
1888                 free_rbufs(info, end, end);
1889
1890                 if (++end == info->rbuf_count)
1891                         end = 0;
1892
1893                 /* if entire list searched then no frame available */
1894                 if (end == start)
1895                         break;
1896         }
1897
1898         if (chars)
1899                 tty_flip_buffer_push(&info->port);
1900 }
1901
1902 /*
1903  * return next bottom half action to perform
1904  */
1905 static int bh_action(struct slgt_info *info)
1906 {
1907         unsigned long flags;
1908         int rc;
1909
1910         spin_lock_irqsave(&info->lock,flags);
1911
1912         if (info->pending_bh & BH_RECEIVE) {
1913                 info->pending_bh &= ~BH_RECEIVE;
1914                 rc = BH_RECEIVE;
1915         } else if (info->pending_bh & BH_TRANSMIT) {
1916                 info->pending_bh &= ~BH_TRANSMIT;
1917                 rc = BH_TRANSMIT;
1918         } else if (info->pending_bh & BH_STATUS) {
1919                 info->pending_bh &= ~BH_STATUS;
1920                 rc = BH_STATUS;
1921         } else {
1922                 /* Mark BH routine as complete */
1923                 info->bh_running = false;
1924                 info->bh_requested = false;
1925                 rc = 0;
1926         }
1927
1928         spin_unlock_irqrestore(&info->lock,flags);
1929
1930         return rc;
1931 }
1932
1933 /*
1934  * perform bottom half processing
1935  */
1936 static void bh_handler(struct work_struct *work)
1937 {
1938         struct slgt_info *info = container_of(work, struct slgt_info, task);
1939         int action;
1940
1941         info->bh_running = true;
1942
1943         while((action = bh_action(info))) {
1944                 switch (action) {
1945                 case BH_RECEIVE:
1946                         DBGBH(("%s bh receive\n", info->device_name));
1947                         switch(info->params.mode) {
1948                         case MGSL_MODE_ASYNC:
1949                                 rx_async(info);
1950                                 break;
1951                         case MGSL_MODE_HDLC:
1952                                 while(rx_get_frame(info));
1953                                 break;
1954                         case MGSL_MODE_RAW:
1955                         case MGSL_MODE_MONOSYNC:
1956                         case MGSL_MODE_BISYNC:
1957                         case MGSL_MODE_XSYNC:
1958                                 while(rx_get_buf(info));
1959                                 break;
1960                         }
1961                         /* restart receiver if rx DMA buffers exhausted */
1962                         if (info->rx_restart)
1963                                 rx_start(info);
1964                         break;
1965                 case BH_TRANSMIT:
1966                         bh_transmit(info);
1967                         break;
1968                 case BH_STATUS:
1969                         DBGBH(("%s bh status\n", info->device_name));
1970                         info->ri_chkcount = 0;
1971                         info->dsr_chkcount = 0;
1972                         info->dcd_chkcount = 0;
1973                         info->cts_chkcount = 0;
1974                         break;
1975                 default:
1976                         DBGBH(("%s unknown action\n", info->device_name));
1977                         break;
1978                 }
1979         }
1980         DBGBH(("%s bh_handler exit\n", info->device_name));
1981 }
1982
1983 static void bh_transmit(struct slgt_info *info)
1984 {
1985         struct tty_struct *tty = info->port.tty;
1986
1987         DBGBH(("%s bh_transmit\n", info->device_name));
1988         if (tty)
1989                 tty_wakeup(tty);
1990 }
1991
1992 static void dsr_change(struct slgt_info *info, unsigned short status)
1993 {
1994         if (status & BIT3) {
1995                 info->signals |= SerialSignal_DSR;
1996                 info->input_signal_events.dsr_up++;
1997         } else {
1998                 info->signals &= ~SerialSignal_DSR;
1999                 info->input_signal_events.dsr_down++;
2000         }
2001         DBGISR(("dsr_change %s signals=%04X\n", info->device_name, info->signals));
2002         if ((info->dsr_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2003                 slgt_irq_off(info, IRQ_DSR);
2004                 return;
2005         }
2006         info->icount.dsr++;
2007         wake_up_interruptible(&info->status_event_wait_q);
2008         wake_up_interruptible(&info->event_wait_q);
2009         info->pending_bh |= BH_STATUS;
2010 }
2011
2012 static void cts_change(struct slgt_info *info, unsigned short status)
2013 {
2014         if (status & BIT2) {
2015                 info->signals |= SerialSignal_CTS;
2016                 info->input_signal_events.cts_up++;
2017         } else {
2018                 info->signals &= ~SerialSignal_CTS;
2019                 info->input_signal_events.cts_down++;
2020         }
2021         DBGISR(("cts_change %s signals=%04X\n", info->device_name, info->signals));
2022         if ((info->cts_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2023                 slgt_irq_off(info, IRQ_CTS);
2024                 return;
2025         }
2026         info->icount.cts++;
2027         wake_up_interruptible(&info->status_event_wait_q);
2028         wake_up_interruptible(&info->event_wait_q);
2029         info->pending_bh |= BH_STATUS;
2030
2031         if (tty_port_cts_enabled(&info->port)) {
2032                 if (info->port.tty) {
2033                         if (info->port.tty->hw_stopped) {
2034                                 if (info->signals & SerialSignal_CTS) {
2035                                         info->port.tty->hw_stopped = 0;
2036                                         info->pending_bh |= BH_TRANSMIT;
2037                                         return;
2038                                 }
2039                         } else {
2040                                 if (!(info->signals & SerialSignal_CTS))
2041                                         info->port.tty->hw_stopped = 1;
2042                         }
2043                 }
2044         }
2045 }
2046
2047 static void dcd_change(struct slgt_info *info, unsigned short status)
2048 {
2049         if (status & BIT1) {
2050                 info->signals |= SerialSignal_DCD;
2051                 info->input_signal_events.dcd_up++;
2052         } else {
2053                 info->signals &= ~SerialSignal_DCD;
2054                 info->input_signal_events.dcd_down++;
2055         }
2056         DBGISR(("dcd_change %s signals=%04X\n", info->device_name, info->signals));
2057         if ((info->dcd_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2058                 slgt_irq_off(info, IRQ_DCD);
2059                 return;
2060         }
2061         info->icount.dcd++;
2062 #if SYNCLINK_GENERIC_HDLC
2063         if (info->netcount) {
2064                 if (info->signals & SerialSignal_DCD)
2065                         netif_carrier_on(info->netdev);
2066                 else
2067                         netif_carrier_off(info->netdev);
2068         }
2069 #endif
2070         wake_up_interruptible(&info->status_event_wait_q);
2071         wake_up_interruptible(&info->event_wait_q);
2072         info->pending_bh |= BH_STATUS;
2073
2074         if (tty_port_check_carrier(&info->port)) {
2075                 if (info->signals & SerialSignal_DCD)
2076                         wake_up_interruptible(&info->port.open_wait);
2077                 else {
2078                         if (info->port.tty)
2079                                 tty_hangup(info->port.tty);
2080                 }
2081         }
2082 }
2083
2084 static void ri_change(struct slgt_info *info, unsigned short status)
2085 {
2086         if (status & BIT0) {
2087                 info->signals |= SerialSignal_RI;
2088                 info->input_signal_events.ri_up++;
2089         } else {
2090                 info->signals &= ~SerialSignal_RI;
2091                 info->input_signal_events.ri_down++;
2092         }
2093         DBGISR(("ri_change %s signals=%04X\n", info->device_name, info->signals));
2094         if ((info->ri_chkcount)++ == IO_PIN_SHUTDOWN_LIMIT) {
2095                 slgt_irq_off(info, IRQ_RI);
2096                 return;
2097         }
2098         info->icount.rng++;
2099         wake_up_interruptible(&info->status_event_wait_q);
2100         wake_up_interruptible(&info->event_wait_q);
2101         info->pending_bh |= BH_STATUS;
2102 }
2103
2104 static void isr_rxdata(struct slgt_info *info)
2105 {
2106         unsigned int count = info->rbuf_fill_count;
2107         unsigned int i = info->rbuf_fill_index;
2108         unsigned short reg;
2109
2110         while (rd_reg16(info, SSR) & IRQ_RXDATA) {
2111                 reg = rd_reg16(info, RDR);
2112                 DBGISR(("isr_rxdata %s RDR=%04X\n", info->device_name, reg));
2113                 if (desc_complete(info->rbufs[i])) {
2114                         /* all buffers full */
2115                         rx_stop(info);
2116                         info->rx_restart = 1;
2117                         continue;
2118                 }
2119                 info->rbufs[i].buf[count++] = (unsigned char)reg;
2120                 /* async mode saves status byte to buffer for each data byte */
2121                 if (info->params.mode == MGSL_MODE_ASYNC)
2122                         info->rbufs[i].buf[count++] = (unsigned char)(reg >> 8);
2123                 if (count == info->rbuf_fill_level || (reg & BIT10)) {
2124                         /* buffer full or end of frame */
2125                         set_desc_count(info->rbufs[i], count);
2126                         set_desc_status(info->rbufs[i], BIT15 | (reg >> 8));
2127                         info->rbuf_fill_count = count = 0;
2128                         if (++i == info->rbuf_count)
2129                                 i = 0;
2130                         info->pending_bh |= BH_RECEIVE;
2131                 }
2132         }
2133
2134         info->rbuf_fill_index = i;
2135         info->rbuf_fill_count = count;
2136 }
2137
2138 static void isr_serial(struct slgt_info *info)
2139 {
2140         unsigned short status = rd_reg16(info, SSR);
2141
2142         DBGISR(("%s isr_serial status=%04X\n", info->device_name, status));
2143
2144         wr_reg16(info, SSR, status); /* clear pending */
2145
2146         info->irq_occurred = true;
2147
2148         if (info->params.mode == MGSL_MODE_ASYNC) {
2149                 if (status & IRQ_TXIDLE) {
2150                         if (info->tx_active)
2151                                 isr_txeom(info, status);
2152                 }
2153                 if (info->rx_pio && (status & IRQ_RXDATA))
2154                         isr_rxdata(info);
2155                 if ((status & IRQ_RXBREAK) && (status & RXBREAK)) {
2156                         info->icount.brk++;
2157                         /* process break detection if tty control allows */
2158                         if (info->port.tty) {
2159                                 if (!(status & info->ignore_status_mask)) {
2160                                         if (info->read_status_mask & MASK_BREAK) {
2161                                                 tty_insert_flip_char(&info->port, 0, TTY_BREAK);
2162                                                 if (info->port.flags & ASYNC_SAK)
2163                                                         do_SAK(info->port.tty);
2164                                         }
2165                                 }
2166                         }
2167                 }
2168         } else {
2169                 if (status & (IRQ_TXIDLE + IRQ_TXUNDER))
2170                         isr_txeom(info, status);
2171                 if (info->rx_pio && (status & IRQ_RXDATA))
2172                         isr_rxdata(info);
2173                 if (status & IRQ_RXIDLE) {
2174                         if (status & RXIDLE)
2175                                 info->icount.rxidle++;
2176                         else
2177                                 info->icount.exithunt++;
2178                         wake_up_interruptible(&info->event_wait_q);
2179                 }
2180
2181                 if (status & IRQ_RXOVER)
2182                         rx_start(info);
2183         }
2184
2185         if (status & IRQ_DSR)
2186                 dsr_change(info, status);
2187         if (status & IRQ_CTS)
2188                 cts_change(info, status);
2189         if (status & IRQ_DCD)
2190                 dcd_change(info, status);
2191         if (status & IRQ_RI)
2192                 ri_change(info, status);
2193 }
2194
2195 static void isr_rdma(struct slgt_info *info)
2196 {
2197         unsigned int status = rd_reg32(info, RDCSR);
2198
2199         DBGISR(("%s isr_rdma status=%08x\n", info->device_name, status));
2200
2201         /* RDCSR (rx DMA control/status)
2202          *
2203          * 31..07  reserved
2204          * 06      save status byte to DMA buffer
2205          * 05      error
2206          * 04      eol (end of list)
2207          * 03      eob (end of buffer)
2208          * 02      IRQ enable
2209          * 01      reset
2210          * 00      enable
2211          */
2212         wr_reg32(info, RDCSR, status);  /* clear pending */
2213
2214         if (status & (BIT5 + BIT4)) {
2215                 DBGISR(("%s isr_rdma rx_restart=1\n", info->device_name));
2216                 info->rx_restart = true;
2217         }
2218         info->pending_bh |= BH_RECEIVE;
2219 }
2220
2221 static void isr_tdma(struct slgt_info *info)
2222 {
2223         unsigned int status = rd_reg32(info, TDCSR);
2224
2225         DBGISR(("%s isr_tdma status=%08x\n", info->device_name, status));
2226
2227         /* TDCSR (tx DMA control/status)
2228          *
2229          * 31..06  reserved
2230          * 05      error
2231          * 04      eol (end of list)
2232          * 03      eob (end of buffer)
2233          * 02      IRQ enable
2234          * 01      reset
2235          * 00      enable
2236          */
2237         wr_reg32(info, TDCSR, status);  /* clear pending */
2238
2239         if (status & (BIT5 + BIT4 + BIT3)) {
2240                 // another transmit buffer has completed
2241                 // run bottom half to get more send data from user
2242                 info->pending_bh |= BH_TRANSMIT;
2243         }
2244 }
2245
2246 /*
2247  * return true if there are unsent tx DMA buffers, otherwise false
2248  *
2249  * if there are unsent buffers then info->tbuf_start
2250  * is set to index of first unsent buffer
2251  */
2252 static bool unsent_tbufs(struct slgt_info *info)
2253 {
2254         unsigned int i = info->tbuf_current;
2255         bool rc = false;
2256
2257         /*
2258          * search backwards from last loaded buffer (precedes tbuf_current)
2259          * for first unsent buffer (desc_count > 0)
2260          */
2261
2262         do {
2263                 if (i)
2264                         i--;
2265                 else
2266                         i = info->tbuf_count - 1;
2267                 if (!desc_count(info->tbufs[i]))
2268                         break;
2269                 info->tbuf_start = i;
2270                 rc = true;
2271         } while (i != info->tbuf_current);
2272
2273         return rc;
2274 }
2275
2276 static void isr_txeom(struct slgt_info *info, unsigned short status)
2277 {
2278         DBGISR(("%s txeom status=%04x\n", info->device_name, status));
2279
2280         slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER);
2281         tdma_reset(info);
2282         if (status & IRQ_TXUNDER) {
2283                 unsigned short val = rd_reg16(info, TCR);
2284                 wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */
2285                 wr_reg16(info, TCR, val); /* clear reset bit */
2286         }
2287
2288         if (info->tx_active) {
2289                 if (info->params.mode != MGSL_MODE_ASYNC) {
2290                         if (status & IRQ_TXUNDER)
2291                                 info->icount.txunder++;
2292                         else if (status & IRQ_TXIDLE)
2293                                 info->icount.txok++;
2294                 }
2295
2296                 if (unsent_tbufs(info)) {
2297                         tx_start(info);
2298                         update_tx_timer(info);
2299                         return;
2300                 }
2301                 info->tx_active = false;
2302
2303                 del_timer(&info->tx_timer);
2304
2305                 if (info->params.mode != MGSL_MODE_ASYNC && info->drop_rts_on_tx_done) {
2306                         info->signals &= ~SerialSignal_RTS;
2307                         info->drop_rts_on_tx_done = false;
2308                         set_signals(info);
2309                 }
2310
2311 #if SYNCLINK_GENERIC_HDLC
2312                 if (info->netcount)
2313                         hdlcdev_tx_done(info);
2314                 else
2315 #endif
2316                 {
2317                         if (info->port.tty && (info->port.tty->stopped || info->port.tty->hw_stopped)) {
2318                                 tx_stop(info);
2319                                 return;
2320                         }
2321                         info->pending_bh |= BH_TRANSMIT;
2322                 }
2323         }
2324 }
2325
2326 static void isr_gpio(struct slgt_info *info, unsigned int changed, unsigned int state)
2327 {
2328         struct cond_wait *w, *prev;
2329
2330         /* wake processes waiting for specific transitions */
2331         for (w = info->gpio_wait_q, prev = NULL ; w != NULL ; w = w->next) {
2332                 if (w->data & changed) {
2333                         w->data = state;
2334                         wake_up_interruptible(&w->q);
2335                         if (prev != NULL)
2336                                 prev->next = w->next;
2337                         else
2338                                 info->gpio_wait_q = w->next;
2339                 } else
2340                         prev = w;
2341         }
2342 }
2343
2344 /* interrupt service routine
2345  *
2346  *      irq     interrupt number
2347  *      dev_id  device ID supplied during interrupt registration
2348  */
2349 static irqreturn_t slgt_interrupt(int dummy, void *dev_id)
2350 {
2351         struct slgt_info *info = dev_id;
2352         unsigned int gsr;
2353         unsigned int i;
2354
2355         DBGISR(("slgt_interrupt irq=%d entry\n", info->irq_level));
2356
2357         while((gsr = rd_reg32(info, GSR) & 0xffffff00)) {
2358                 DBGISR(("%s gsr=%08x\n", info->device_name, gsr));
2359                 info->irq_occurred = true;
2360                 for(i=0; i < info->port_count ; i++) {
2361                         if (info->port_array[i] == NULL)
2362                                 continue;
2363                         spin_lock(&info->port_array[i]->lock);
2364                         if (gsr & (BIT8 << i))
2365                                 isr_serial(info->port_array[i]);
2366                         if (gsr & (BIT16 << (i*2)))
2367                                 isr_rdma(info->port_array[i]);
2368                         if (gsr & (BIT17 << (i*2)))
2369                                 isr_tdma(info->port_array[i]);
2370                         spin_unlock(&info->port_array[i]->lock);
2371                 }
2372         }
2373
2374         if (info->gpio_present) {
2375                 unsigned int state;
2376                 unsigned int changed;
2377                 spin_lock(&info->lock);
2378                 while ((changed = rd_reg32(info, IOSR)) != 0) {
2379                         DBGISR(("%s iosr=%08x\n", info->device_name, changed));
2380                         /* read latched state of GPIO signals */
2381                         state = rd_reg32(info, IOVR);
2382                         /* clear pending GPIO interrupt bits */
2383                         wr_reg32(info, IOSR, changed);
2384                         for (i=0 ; i < info->port_count ; i++) {
2385                                 if (info->port_array[i] != NULL)
2386                                         isr_gpio(info->port_array[i], changed, state);
2387                         }
2388                 }
2389                 spin_unlock(&info->lock);
2390         }
2391
2392         for(i=0; i < info->port_count ; i++) {
2393                 struct slgt_info *port = info->port_array[i];
2394                 if (port == NULL)
2395                         continue;
2396                 spin_lock(&port->lock);
2397                 if ((port->port.count || port->netcount) &&
2398                     port->pending_bh && !port->bh_running &&
2399                     !port->bh_requested) {
2400                         DBGISR(("%s bh queued\n", port->device_name));
2401                         schedule_work(&port->task);
2402                         port->bh_requested = true;
2403                 }
2404                 spin_unlock(&port->lock);
2405         }
2406
2407         DBGISR(("slgt_interrupt irq=%d exit\n", info->irq_level));
2408         return IRQ_HANDLED;
2409 }
2410
2411 static int startup(struct slgt_info *info)
2412 {
2413         DBGINFO(("%s startup\n", info->device_name));
2414
2415         if (tty_port_initialized(&info->port))
2416                 return 0;
2417
2418         if (!info->tx_buf) {
2419                 info->tx_buf = kmalloc(info->max_frame_size, GFP_KERNEL);
2420                 if (!info->tx_buf) {
2421                         DBGERR(("%s can't allocate tx buffer\n", info->device_name));
2422                         return -ENOMEM;
2423                 }
2424         }
2425
2426         info->pending_bh = 0;
2427
2428         memset(&info->icount, 0, sizeof(info->icount));
2429
2430         /* program hardware for current parameters */
2431         change_params(info);
2432
2433         if (info->port.tty)
2434                 clear_bit(TTY_IO_ERROR, &info->port.tty->flags);
2435
2436         tty_port_set_initialized(&info->port, 1);
2437
2438         return 0;
2439 }
2440
2441 /*
2442  *  called by close() and hangup() to shutdown hardware
2443  */
2444 static void shutdown(struct slgt_info *info)
2445 {
2446         unsigned long flags;
2447
2448         if (!tty_port_initialized(&info->port))
2449                 return;
2450
2451         DBGINFO(("%s shutdown\n", info->device_name));
2452
2453         /* clear status wait queue because status changes */
2454         /* can't happen after shutting down the hardware */
2455         wake_up_interruptible(&info->status_event_wait_q);
2456         wake_up_interruptible(&info->event_wait_q);
2457
2458         del_timer_sync(&info->tx_timer);
2459         del_timer_sync(&info->rx_timer);
2460
2461         kfree(info->tx_buf);
2462         info->tx_buf = NULL;
2463
2464         spin_lock_irqsave(&info->lock,flags);
2465
2466         tx_stop(info);
2467         rx_stop(info);
2468
2469         slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
2470
2471         if (!info->port.tty || info->port.tty->termios.c_cflag & HUPCL) {
2472                 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
2473                 set_signals(info);
2474         }
2475
2476         flush_cond_wait(&info->gpio_wait_q);
2477
2478         spin_unlock_irqrestore(&info->lock,flags);
2479
2480         if (info->port.tty)
2481                 set_bit(TTY_IO_ERROR, &info->port.tty->flags);
2482
2483         tty_port_set_initialized(&info->port, 0);
2484 }
2485
2486 static void program_hw(struct slgt_info *info)
2487 {
2488         unsigned long flags;
2489
2490         spin_lock_irqsave(&info->lock,flags);
2491
2492         rx_stop(info);
2493         tx_stop(info);
2494
2495         if (info->params.mode != MGSL_MODE_ASYNC ||
2496             info->netcount)
2497                 sync_mode(info);
2498         else
2499                 async_mode(info);
2500
2501         set_signals(info);
2502
2503         info->dcd_chkcount = 0;
2504         info->cts_chkcount = 0;
2505         info->ri_chkcount = 0;
2506         info->dsr_chkcount = 0;
2507
2508         slgt_irq_on(info, IRQ_DCD | IRQ_CTS | IRQ_DSR | IRQ_RI);
2509         get_signals(info);
2510
2511         if (info->netcount ||
2512             (info->port.tty && info->port.tty->termios.c_cflag & CREAD))
2513                 rx_start(info);
2514
2515         spin_unlock_irqrestore(&info->lock,flags);
2516 }
2517
2518 /*
2519  * reconfigure adapter based on new parameters
2520  */
2521 static void change_params(struct slgt_info *info)
2522 {
2523         unsigned cflag;
2524         int bits_per_char;
2525
2526         if (!info->port.tty)
2527                 return;
2528         DBGINFO(("%s change_params\n", info->device_name));
2529
2530         cflag = info->port.tty->termios.c_cflag;
2531
2532         /* if B0 rate (hangup) specified then negate RTS and DTR */
2533         /* otherwise assert RTS and DTR */
2534         if (cflag & CBAUD)
2535                 info->signals |= SerialSignal_RTS | SerialSignal_DTR;
2536         else
2537                 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
2538
2539         /* byte size and parity */
2540
2541         switch (cflag & CSIZE) {
2542         case CS5: info->params.data_bits = 5; break;
2543         case CS6: info->params.data_bits = 6; break;
2544         case CS7: info->params.data_bits = 7; break;
2545         case CS8: info->params.data_bits = 8; break;
2546         default:  info->params.data_bits = 7; break;
2547         }
2548
2549         info->params.stop_bits = (cflag & CSTOPB) ? 2 : 1;
2550
2551         if (cflag & PARENB)
2552                 info->params.parity = (cflag & PARODD) ? ASYNC_PARITY_ODD : ASYNC_PARITY_EVEN;
2553         else
2554                 info->params.parity = ASYNC_PARITY_NONE;
2555
2556         /* calculate number of jiffies to transmit a full
2557          * FIFO (32 bytes) at specified data rate
2558          */
2559         bits_per_char = info->params.data_bits +
2560                         info->params.stop_bits + 1;
2561
2562         info->params.data_rate = tty_get_baud_rate(info->port.tty);
2563
2564         if (info->params.data_rate) {
2565                 info->timeout = (32*HZ*bits_per_char) /
2566                                 info->params.data_rate;
2567         }
2568         info->timeout += HZ/50;         /* Add .02 seconds of slop */
2569
2570         tty_port_set_cts_flow(&info->port, cflag & CRTSCTS);
2571         tty_port_set_check_carrier(&info->port, ~cflag & CLOCAL);
2572
2573         /* process tty input control flags */
2574
2575         info->read_status_mask = IRQ_RXOVER;
2576         if (I_INPCK(info->port.tty))
2577                 info->read_status_mask |= MASK_PARITY | MASK_FRAMING;
2578         if (I_BRKINT(info->port.tty) || I_PARMRK(info->port.tty))
2579                 info->read_status_mask |= MASK_BREAK;
2580         if (I_IGNPAR(info->port.tty))
2581                 info->ignore_status_mask |= MASK_PARITY | MASK_FRAMING;
2582         if (I_IGNBRK(info->port.tty)) {
2583                 info->ignore_status_mask |= MASK_BREAK;
2584                 /* If ignoring parity and break indicators, ignore
2585                  * overruns too.  (For real raw support).
2586                  */
2587                 if (I_IGNPAR(info->port.tty))
2588                         info->ignore_status_mask |= MASK_OVERRUN;
2589         }
2590
2591         program_hw(info);
2592 }
2593
2594 static int get_stats(struct slgt_info *info, struct mgsl_icount __user *user_icount)
2595 {
2596         DBGINFO(("%s get_stats\n",  info->device_name));
2597         if (!user_icount) {
2598                 memset(&info->icount, 0, sizeof(info->icount));
2599         } else {
2600                 if (copy_to_user(user_icount, &info->icount, sizeof(struct mgsl_icount)))
2601                         return -EFAULT;
2602         }
2603         return 0;
2604 }
2605
2606 static int get_params(struct slgt_info *info, MGSL_PARAMS __user *user_params)
2607 {
2608         DBGINFO(("%s get_params\n", info->device_name));
2609         if (copy_to_user(user_params, &info->params, sizeof(MGSL_PARAMS)))
2610                 return -EFAULT;
2611         return 0;
2612 }
2613
2614 static int set_params(struct slgt_info *info, MGSL_PARAMS __user *new_params)
2615 {
2616         unsigned long flags;
2617         MGSL_PARAMS tmp_params;
2618
2619         DBGINFO(("%s set_params\n", info->device_name));
2620         if (copy_from_user(&tmp_params, new_params, sizeof(MGSL_PARAMS)))
2621                 return -EFAULT;
2622
2623         spin_lock_irqsave(&info->lock, flags);
2624         if (tmp_params.mode == MGSL_MODE_BASE_CLOCK)
2625                 info->base_clock = tmp_params.clock_speed;
2626         else
2627                 memcpy(&info->params, &tmp_params, sizeof(MGSL_PARAMS));
2628         spin_unlock_irqrestore(&info->lock, flags);
2629
2630         program_hw(info);
2631
2632         return 0;
2633 }
2634
2635 static int get_txidle(struct slgt_info *info, int __user *idle_mode)
2636 {
2637         DBGINFO(("%s get_txidle=%d\n", info->device_name, info->idle_mode));
2638         if (put_user(info->idle_mode, idle_mode))
2639                 return -EFAULT;
2640         return 0;
2641 }
2642
2643 static int set_txidle(struct slgt_info *info, int idle_mode)
2644 {
2645         unsigned long flags;
2646         DBGINFO(("%s set_txidle(%d)\n", info->device_name, idle_mode));
2647         spin_lock_irqsave(&info->lock,flags);
2648         info->idle_mode = idle_mode;
2649         if (info->params.mode != MGSL_MODE_ASYNC)
2650                 tx_set_idle(info);
2651         spin_unlock_irqrestore(&info->lock,flags);
2652         return 0;
2653 }
2654
2655 static int tx_enable(struct slgt_info *info, int enable)
2656 {
2657         unsigned long flags;
2658         DBGINFO(("%s tx_enable(%d)\n", info->device_name, enable));
2659         spin_lock_irqsave(&info->lock,flags);
2660         if (enable) {
2661                 if (!info->tx_enabled)
2662                         tx_start(info);
2663         } else {
2664                 if (info->tx_enabled)
2665                         tx_stop(info);
2666         }
2667         spin_unlock_irqrestore(&info->lock,flags);
2668         return 0;
2669 }
2670
2671 /*
2672  * abort transmit HDLC frame
2673  */
2674 static int tx_abort(struct slgt_info *info)
2675 {
2676         unsigned long flags;
2677         DBGINFO(("%s tx_abort\n", info->device_name));
2678         spin_lock_irqsave(&info->lock,flags);
2679         tdma_reset(info);
2680         spin_unlock_irqrestore(&info->lock,flags);
2681         return 0;
2682 }
2683
2684 static int rx_enable(struct slgt_info *info, int enable)
2685 {
2686         unsigned long flags;
2687         unsigned int rbuf_fill_level;
2688         DBGINFO(("%s rx_enable(%08x)\n", info->device_name, enable));
2689         spin_lock_irqsave(&info->lock,flags);
2690         /*
2691          * enable[31..16] = receive DMA buffer fill level
2692          * 0 = noop (leave fill level unchanged)
2693          * fill level must be multiple of 4 and <= buffer size
2694          */
2695         rbuf_fill_level = ((unsigned int)enable) >> 16;
2696         if (rbuf_fill_level) {
2697                 if ((rbuf_fill_level > DMABUFSIZE) || (rbuf_fill_level % 4)) {
2698                         spin_unlock_irqrestore(&info->lock, flags);
2699                         return -EINVAL;
2700                 }
2701                 info->rbuf_fill_level = rbuf_fill_level;
2702                 if (rbuf_fill_level < 128)
2703                         info->rx_pio = 1; /* PIO mode */
2704                 else
2705                         info->rx_pio = 0; /* DMA mode */
2706                 rx_stop(info); /* restart receiver to use new fill level */
2707         }
2708
2709         /*
2710          * enable[1..0] = receiver enable command
2711          * 0 = disable
2712          * 1 = enable
2713          * 2 = enable or force hunt mode if already enabled
2714          */
2715         enable &= 3;
2716         if (enable) {
2717                 if (!info->rx_enabled)
2718                         rx_start(info);
2719                 else if (enable == 2) {
2720                         /* force hunt mode (write 1 to RCR[3]) */
2721                         wr_reg16(info, RCR, rd_reg16(info, RCR) | BIT3);
2722                 }
2723         } else {
2724                 if (info->rx_enabled)
2725                         rx_stop(info);
2726         }
2727         spin_unlock_irqrestore(&info->lock,flags);
2728         return 0;
2729 }
2730
2731 /*
2732  *  wait for specified event to occur
2733  */
2734 static int wait_mgsl_event(struct slgt_info *info, int __user *mask_ptr)
2735 {
2736         unsigned long flags;
2737         int s;
2738         int rc=0;
2739         struct mgsl_icount cprev, cnow;
2740         int events;
2741         int mask;
2742         struct  _input_signal_events oldsigs, newsigs;
2743         DECLARE_WAITQUEUE(wait, current);
2744
2745         if (get_user(mask, mask_ptr))
2746                 return -EFAULT;
2747
2748         DBGINFO(("%s wait_mgsl_event(%d)\n", info->device_name, mask));
2749
2750         spin_lock_irqsave(&info->lock,flags);
2751
2752         /* return immediately if state matches requested events */
2753         get_signals(info);
2754         s = info->signals;
2755
2756         events = mask &
2757                 ( ((s & SerialSignal_DSR) ? MgslEvent_DsrActive:MgslEvent_DsrInactive) +
2758                   ((s & SerialSignal_DCD) ? MgslEvent_DcdActive:MgslEvent_DcdInactive) +
2759                   ((s & SerialSignal_CTS) ? MgslEvent_CtsActive:MgslEvent_CtsInactive) +
2760                   ((s & SerialSignal_RI)  ? MgslEvent_RiActive :MgslEvent_RiInactive) );
2761         if (events) {
2762                 spin_unlock_irqrestore(&info->lock,flags);
2763                 goto exit;
2764         }
2765
2766         /* save current irq counts */
2767         cprev = info->icount;
2768         oldsigs = info->input_signal_events;
2769
2770         /* enable hunt and idle irqs if needed */
2771         if (mask & (MgslEvent_ExitHuntMode+MgslEvent_IdleReceived)) {
2772                 unsigned short val = rd_reg16(info, SCR);
2773                 if (!(val & IRQ_RXIDLE))
2774                         wr_reg16(info, SCR, (unsigned short)(val | IRQ_RXIDLE));
2775         }
2776
2777         set_current_state(TASK_INTERRUPTIBLE);
2778         add_wait_queue(&info->event_wait_q, &wait);
2779
2780         spin_unlock_irqrestore(&info->lock,flags);
2781
2782         for(;;) {
2783                 schedule();
2784                 if (signal_pending(current)) {
2785                         rc = -ERESTARTSYS;
2786                         break;
2787                 }
2788
2789                 /* get current irq counts */
2790                 spin_lock_irqsave(&info->lock,flags);
2791                 cnow = info->icount;
2792                 newsigs = info->input_signal_events;
2793                 set_current_state(TASK_INTERRUPTIBLE);
2794                 spin_unlock_irqrestore(&info->lock,flags);
2795
2796                 /* if no change, wait aborted for some reason */
2797                 if (newsigs.dsr_up   == oldsigs.dsr_up   &&
2798                     newsigs.dsr_down == oldsigs.dsr_down &&
2799                     newsigs.dcd_up   == oldsigs.dcd_up   &&
2800                     newsigs.dcd_down == oldsigs.dcd_down &&
2801                     newsigs.cts_up   == oldsigs.cts_up   &&
2802                     newsigs.cts_down == oldsigs.cts_down &&
2803                     newsigs.ri_up    == oldsigs.ri_up    &&
2804                     newsigs.ri_down  == oldsigs.ri_down  &&
2805                     cnow.exithunt    == cprev.exithunt   &&
2806                     cnow.rxidle      == cprev.rxidle) {
2807                         rc = -EIO;
2808                         break;
2809                 }
2810
2811                 events = mask &
2812                         ( (newsigs.dsr_up   != oldsigs.dsr_up   ? MgslEvent_DsrActive:0)   +
2813                           (newsigs.dsr_down != oldsigs.dsr_down ? MgslEvent_DsrInactive:0) +
2814                           (newsigs.dcd_up   != oldsigs.dcd_up   ? MgslEvent_DcdActive:0)   +
2815                           (newsigs.dcd_down != oldsigs.dcd_down ? MgslEvent_DcdInactive:0) +
2816                           (newsigs.cts_up   != oldsigs.cts_up   ? MgslEvent_CtsActive:0)   +
2817                           (newsigs.cts_down != oldsigs.cts_down ? MgslEvent_CtsInactive:0) +
2818                           (newsigs.ri_up    != oldsigs.ri_up    ? MgslEvent_RiActive:0)    +
2819                           (newsigs.ri_down  != oldsigs.ri_down  ? MgslEvent_RiInactive:0)  +
2820                           (cnow.exithunt    != cprev.exithunt   ? MgslEvent_ExitHuntMode:0) +
2821                           (cnow.rxidle      != cprev.rxidle     ? MgslEvent_IdleReceived:0) );
2822                 if (events)
2823                         break;
2824
2825                 cprev = cnow;
2826                 oldsigs = newsigs;
2827         }
2828
2829         remove_wait_queue(&info->event_wait_q, &wait);
2830         set_current_state(TASK_RUNNING);
2831
2832
2833         if (mask & (MgslEvent_ExitHuntMode + MgslEvent_IdleReceived)) {
2834                 spin_lock_irqsave(&info->lock,flags);
2835                 if (!waitqueue_active(&info->event_wait_q)) {
2836                         /* disable enable exit hunt mode/idle rcvd IRQs */
2837                         wr_reg16(info, SCR,
2838                                 (unsigned short)(rd_reg16(info, SCR) & ~IRQ_RXIDLE));
2839                 }
2840                 spin_unlock_irqrestore(&info->lock,flags);
2841         }
2842 exit:
2843         if (rc == 0)
2844                 rc = put_user(events, mask_ptr);
2845         return rc;
2846 }
2847
2848 static int get_interface(struct slgt_info *info, int __user *if_mode)
2849 {
2850         DBGINFO(("%s get_interface=%x\n", info->device_name, info->if_mode));
2851         if (put_user(info->if_mode, if_mode))
2852                 return -EFAULT;
2853         return 0;
2854 }
2855
2856 static int set_interface(struct slgt_info *info, int if_mode)
2857 {
2858         unsigned long flags;
2859         unsigned short val;
2860
2861         DBGINFO(("%s set_interface=%x)\n", info->device_name, if_mode));
2862         spin_lock_irqsave(&info->lock,flags);
2863         info->if_mode = if_mode;
2864
2865         msc_set_vcr(info);
2866
2867         /* TCR (tx control) 07  1=RTS driver control */
2868         val = rd_reg16(info, TCR);
2869         if (info->if_mode & MGSL_INTERFACE_RTS_EN)
2870                 val |= BIT7;
2871         else
2872                 val &= ~BIT7;
2873         wr_reg16(info, TCR, val);
2874
2875         spin_unlock_irqrestore(&info->lock,flags);
2876         return 0;
2877 }
2878
2879 static int get_xsync(struct slgt_info *info, int __user *xsync)
2880 {
2881         DBGINFO(("%s get_xsync=%x\n", info->device_name, info->xsync));
2882         if (put_user(info->xsync, xsync))
2883                 return -EFAULT;
2884         return 0;
2885 }
2886
2887 /*
2888  * set extended sync pattern (1 to 4 bytes) for extended sync mode
2889  *
2890  * sync pattern is contained in least significant bytes of value
2891  * most significant byte of sync pattern is oldest (1st sent/detected)
2892  */
2893 static int set_xsync(struct slgt_info *info, int xsync)
2894 {
2895         unsigned long flags;
2896
2897         DBGINFO(("%s set_xsync=%x)\n", info->device_name, xsync));
2898         spin_lock_irqsave(&info->lock, flags);
2899         info->xsync = xsync;
2900         wr_reg32(info, XSR, xsync);
2901         spin_unlock_irqrestore(&info->lock, flags);
2902         return 0;
2903 }
2904
2905 static int get_xctrl(struct slgt_info *info, int __user *xctrl)
2906 {
2907         DBGINFO(("%s get_xctrl=%x\n", info->device_name, info->xctrl));
2908         if (put_user(info->xctrl, xctrl))
2909                 return -EFAULT;
2910         return 0;
2911 }
2912
2913 /*
2914  * set extended control options
2915  *
2916  * xctrl[31:19] reserved, must be zero
2917  * xctrl[18:17] extended sync pattern length in bytes
2918  *              00 = 1 byte  in xsr[7:0]
2919  *              01 = 2 bytes in xsr[15:0]
2920  *              10 = 3 bytes in xsr[23:0]
2921  *              11 = 4 bytes in xsr[31:0]
2922  * xctrl[16]    1 = enable terminal count, 0=disabled
2923  * xctrl[15:0]  receive terminal count for fixed length packets
2924  *              value is count minus one (0 = 1 byte packet)
2925  *              when terminal count is reached, receiver
2926  *              automatically returns to hunt mode and receive
2927  *              FIFO contents are flushed to DMA buffers with
2928  *              end of frame (EOF) status
2929  */
2930 static int set_xctrl(struct slgt_info *info, int xctrl)
2931 {
2932         unsigned long flags;
2933
2934         DBGINFO(("%s set_xctrl=%x)\n", info->device_name, xctrl));
2935         spin_lock_irqsave(&info->lock, flags);
2936         info->xctrl = xctrl;
2937         wr_reg32(info, XCR, xctrl);
2938         spin_unlock_irqrestore(&info->lock, flags);
2939         return 0;
2940 }
2941
2942 /*
2943  * set general purpose IO pin state and direction
2944  *
2945  * user_gpio fields:
2946  * state   each bit indicates a pin state
2947  * smask   set bit indicates pin state to set
2948  * dir     each bit indicates a pin direction (0=input, 1=output)
2949  * dmask   set bit indicates pin direction to set
2950  */
2951 static int set_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2952 {
2953         unsigned long flags;
2954         struct gpio_desc gpio;
2955         __u32 data;
2956
2957         if (!info->gpio_present)
2958                 return -EINVAL;
2959         if (copy_from_user(&gpio, user_gpio, sizeof(gpio)))
2960                 return -EFAULT;
2961         DBGINFO(("%s set_gpio state=%08x smask=%08x dir=%08x dmask=%08x\n",
2962                  info->device_name, gpio.state, gpio.smask,
2963                  gpio.dir, gpio.dmask));
2964
2965         spin_lock_irqsave(&info->port_array[0]->lock, flags);
2966         if (gpio.dmask) {
2967                 data = rd_reg32(info, IODR);
2968                 data |= gpio.dmask & gpio.dir;
2969                 data &= ~(gpio.dmask & ~gpio.dir);
2970                 wr_reg32(info, IODR, data);
2971         }
2972         if (gpio.smask) {
2973                 data = rd_reg32(info, IOVR);
2974                 data |= gpio.smask & gpio.state;
2975                 data &= ~(gpio.smask & ~gpio.state);
2976                 wr_reg32(info, IOVR, data);
2977         }
2978         spin_unlock_irqrestore(&info->port_array[0]->lock, flags);
2979
2980         return 0;
2981 }
2982
2983 /*
2984  * get general purpose IO pin state and direction
2985  */
2986 static int get_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
2987 {
2988         struct gpio_desc gpio;
2989         if (!info->gpio_present)
2990                 return -EINVAL;
2991         gpio.state = rd_reg32(info, IOVR);
2992         gpio.smask = 0xffffffff;
2993         gpio.dir   = rd_reg32(info, IODR);
2994         gpio.dmask = 0xffffffff;
2995         if (copy_to_user(user_gpio, &gpio, sizeof(gpio)))
2996                 return -EFAULT;
2997         DBGINFO(("%s get_gpio state=%08x dir=%08x\n",
2998                  info->device_name, gpio.state, gpio.dir));
2999         return 0;
3000 }
3001
3002 /*
3003  * conditional wait facility
3004  */
3005 static void init_cond_wait(struct cond_wait *w, unsigned int data)
3006 {
3007         init_waitqueue_head(&w->q);
3008         init_waitqueue_entry(&w->wait, current);
3009         w->data = data;
3010 }
3011
3012 static void add_cond_wait(struct cond_wait **head, struct cond_wait *w)
3013 {
3014         set_current_state(TASK_INTERRUPTIBLE);
3015         add_wait_queue(&w->q, &w->wait);
3016         w->next = *head;
3017         *head = w;
3018 }
3019
3020 static void remove_cond_wait(struct cond_wait **head, struct cond_wait *cw)
3021 {
3022         struct cond_wait *w, *prev;
3023         remove_wait_queue(&cw->q, &cw->wait);
3024         set_current_state(TASK_RUNNING);
3025         for (w = *head, prev = NULL ; w != NULL ; prev = w, w = w->next) {
3026                 if (w == cw) {
3027                         if (prev != NULL)
3028                                 prev->next = w->next;
3029                         else
3030                                 *head = w->next;
3031                         break;
3032                 }
3033         }
3034 }
3035
3036 static void flush_cond_wait(struct cond_wait **head)
3037 {
3038         while (*head != NULL) {
3039                 wake_up_interruptible(&(*head)->q);
3040                 *head = (*head)->next;
3041         }
3042 }
3043
3044 /*
3045  * wait for general purpose I/O pin(s) to enter specified state
3046  *
3047  * user_gpio fields:
3048  * state - bit indicates target pin state
3049  * smask - set bit indicates watched pin
3050  *
3051  * The wait ends when at least one watched pin enters the specified
3052  * state. When 0 (no error) is returned, user_gpio->state is set to the
3053  * state of all GPIO pins when the wait ends.
3054  *
3055  * Note: Each pin may be a dedicated input, dedicated output, or
3056  * configurable input/output. The number and configuration of pins
3057  * varies with the specific adapter model. Only input pins (dedicated
3058  * or configured) can be monitored with this function.
3059  */
3060 static int wait_gpio(struct slgt_info *info, struct gpio_desc __user *user_gpio)
3061 {
3062         unsigned long flags;
3063         int rc = 0;
3064         struct gpio_desc gpio;
3065         struct cond_wait wait;
3066         u32 state;
3067
3068         if (!info->gpio_present)
3069                 return -EINVAL;
3070         if (copy_from_user(&gpio, user_gpio, sizeof(gpio)))
3071                 return -EFAULT;
3072         DBGINFO(("%s wait_gpio() state=%08x smask=%08x\n",
3073                  info->device_name, gpio.state, gpio.smask));
3074         /* ignore output pins identified by set IODR bit */
3075         if ((gpio.smask &= ~rd_reg32(info, IODR)) == 0)
3076                 return -EINVAL;
3077         init_cond_wait(&wait, gpio.smask);
3078
3079         spin_lock_irqsave(&info->port_array[0]->lock, flags);
3080         /* enable interrupts for watched pins */
3081         wr_reg32(info, IOER, rd_reg32(info, IOER) | gpio.smask);
3082         /* get current pin states */
3083         state = rd_reg32(info, IOVR);
3084
3085         if (gpio.smask & ~(state ^ gpio.state)) {
3086                 /* already in target state */
3087                 gpio.state = state;
3088         } else {
3089                 /* wait for target state */
3090                 add_cond_wait(&info->gpio_wait_q, &wait);
3091                 spin_unlock_irqrestore(&info->port_array[0]->lock, flags);
3092                 schedule();
3093                 if (signal_pending(current))
3094                         rc = -ERESTARTSYS;
3095                 else
3096                         gpio.state = wait.data;
3097                 spin_lock_irqsave(&info->port_array[0]->lock, flags);
3098                 remove_cond_wait(&info->gpio_wait_q, &wait);
3099         }
3100
3101         /* disable all GPIO interrupts if no waiting processes */
3102         if (info->gpio_wait_q == NULL)
3103                 wr_reg32(info, IOER, 0);
3104         spin_unlock_irqrestore(&info->port_array[0]->lock, flags);
3105
3106         if ((rc == 0) && copy_to_user(user_gpio, &gpio, sizeof(gpio)))
3107                 rc = -EFAULT;
3108         return rc;
3109 }
3110
3111 static int modem_input_wait(struct slgt_info *info,int arg)
3112 {
3113         unsigned long flags;
3114         int rc;
3115         struct mgsl_icount cprev, cnow;
3116         DECLARE_WAITQUEUE(wait, current);
3117
3118         /* save current irq counts */
3119         spin_lock_irqsave(&info->lock,flags);
3120         cprev = info->icount;
3121         add_wait_queue(&info->status_event_wait_q, &wait);
3122         set_current_state(TASK_INTERRUPTIBLE);
3123         spin_unlock_irqrestore(&info->lock,flags);
3124
3125         for(;;) {
3126                 schedule();
3127                 if (signal_pending(current)) {
3128                         rc = -ERESTARTSYS;
3129                         break;
3130                 }
3131
3132                 /* get new irq counts */
3133                 spin_lock_irqsave(&info->lock,flags);
3134                 cnow = info->icount;
3135                 set_current_state(TASK_INTERRUPTIBLE);
3136                 spin_unlock_irqrestore(&info->lock,flags);
3137
3138                 /* if no change, wait aborted for some reason */
3139                 if (cnow.rng == cprev.rng && cnow.dsr == cprev.dsr &&
3140                     cnow.dcd == cprev.dcd && cnow.cts == cprev.cts) {
3141                         rc = -EIO;
3142                         break;
3143                 }
3144
3145                 /* check for change in caller specified modem input */
3146                 if ((arg & TIOCM_RNG && cnow.rng != cprev.rng) ||
3147                     (arg & TIOCM_DSR && cnow.dsr != cprev.dsr) ||
3148                     (arg & TIOCM_CD  && cnow.dcd != cprev.dcd) ||
3149                     (arg & TIOCM_CTS && cnow.cts != cprev.cts)) {
3150                         rc = 0;
3151                         break;
3152                 }
3153
3154                 cprev = cnow;
3155         }
3156         remove_wait_queue(&info->status_event_wait_q, &wait);
3157         set_current_state(TASK_RUNNING);
3158         return rc;
3159 }
3160
3161 /*
3162  *  return state of serial control and status signals
3163  */
3164 static int tiocmget(struct tty_struct *tty)
3165 {
3166         struct slgt_info *info = tty->driver_data;
3167         unsigned int result;
3168         unsigned long flags;
3169
3170         spin_lock_irqsave(&info->lock,flags);
3171         get_signals(info);
3172         spin_unlock_irqrestore(&info->lock,flags);
3173
3174         result = ((info->signals & SerialSignal_RTS) ? TIOCM_RTS:0) +
3175                 ((info->signals & SerialSignal_DTR) ? TIOCM_DTR:0) +
3176                 ((info->signals & SerialSignal_DCD) ? TIOCM_CAR:0) +
3177                 ((info->signals & SerialSignal_RI)  ? TIOCM_RNG:0) +
3178                 ((info->signals & SerialSignal_DSR) ? TIOCM_DSR:0) +
3179                 ((info->signals & SerialSignal_CTS) ? TIOCM_CTS:0);
3180
3181         DBGINFO(("%s tiocmget value=%08X\n", info->device_name, result));
3182         return result;
3183 }
3184
3185 /*
3186  * set modem control signals (DTR/RTS)
3187  *
3188  *      cmd     signal command: TIOCMBIS = set bit TIOCMBIC = clear bit
3189  *              TIOCMSET = set/clear signal values
3190  *      value   bit mask for command
3191  */
3192 static int tiocmset(struct tty_struct *tty,
3193                     unsigned int set, unsigned int clear)
3194 {
3195         struct slgt_info *info = tty->driver_data;
3196         unsigned long flags;
3197
3198         DBGINFO(("%s tiocmset(%x,%x)\n", info->device_name, set, clear));
3199
3200         if (set & TIOCM_RTS)
3201                 info->signals |= SerialSignal_RTS;
3202         if (set & TIOCM_DTR)
3203                 info->signals |= SerialSignal_DTR;
3204         if (clear & TIOCM_RTS)
3205                 info->signals &= ~SerialSignal_RTS;
3206         if (clear & TIOCM_DTR)
3207                 info->signals &= ~SerialSignal_DTR;
3208
3209         spin_lock_irqsave(&info->lock,flags);
3210         set_signals(info);
3211         spin_unlock_irqrestore(&info->lock,flags);
3212         return 0;
3213 }
3214
3215 static int carrier_raised(struct tty_port *port)
3216 {
3217         unsigned long flags;
3218         struct slgt_info *info = container_of(port, struct slgt_info, port);
3219
3220         spin_lock_irqsave(&info->lock,flags);
3221         get_signals(info);
3222         spin_unlock_irqrestore(&info->lock,flags);
3223         return (info->signals & SerialSignal_DCD) ? 1 : 0;
3224 }
3225
3226 static void dtr_rts(struct tty_port *port, int on)
3227 {
3228         unsigned long flags;
3229         struct slgt_info *info = container_of(port, struct slgt_info, port);
3230
3231         spin_lock_irqsave(&info->lock,flags);
3232         if (on)
3233                 info->signals |= SerialSignal_RTS | SerialSignal_DTR;
3234         else
3235                 info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
3236         set_signals(info);
3237         spin_unlock_irqrestore(&info->lock,flags);
3238 }
3239
3240
3241 /*
3242  *  block current process until the device is ready to open
3243  */
3244 static int block_til_ready(struct tty_struct *tty, struct file *filp,
3245                            struct slgt_info *info)
3246 {
3247         DECLARE_WAITQUEUE(wait, current);
3248         int             retval;
3249         bool            do_clocal = false;
3250         unsigned long   flags;
3251         int             cd;
3252         struct tty_port *port = &info->port;
3253
3254         DBGINFO(("%s block_til_ready\n", tty->driver->name));
3255
3256         if (filp->f_flags & O_NONBLOCK || tty_io_error(tty)) {
3257                 /* nonblock mode is set or port is not enabled */
3258                 tty_port_set_active(port, 1);
3259                 return 0;
3260         }
3261
3262         if (C_CLOCAL(tty))
3263                 do_clocal = true;
3264
3265         /* Wait for carrier detect and the line to become
3266          * free (i.e., not in use by the callout).  While we are in
3267          * this loop, port->count is dropped by one, so that
3268          * close() knows when to free things.  We restore it upon
3269          * exit, either normal or abnormal.
3270          */
3271
3272         retval = 0;
3273         add_wait_queue(&port->open_wait, &wait);
3274
3275         spin_lock_irqsave(&info->lock, flags);
3276         port->count--;
3277         spin_unlock_irqrestore(&info->lock, flags);
3278         port->blocked_open++;
3279
3280         while (1) {
3281                 if (C_BAUD(tty) && tty_port_initialized(port))
3282                         tty_port_raise_dtr_rts(port);
3283
3284                 set_current_state(TASK_INTERRUPTIBLE);
3285
3286                 if (tty_hung_up_p(filp) || !tty_port_initialized(port)) {
3287                         retval = (port->flags & ASYNC_HUP_NOTIFY) ?
3288                                         -EAGAIN : -ERESTARTSYS;
3289                         break;
3290                 }
3291
3292                 cd = tty_port_carrier_raised(port);
3293                 if (do_clocal || cd)
3294                         break;
3295
3296                 if (signal_pending(current)) {
3297                         retval = -ERESTARTSYS;
3298                         break;
3299                 }
3300
3301                 DBGINFO(("%s block_til_ready wait\n", tty->driver->name));
3302                 tty_unlock(tty);
3303                 schedule();
3304                 tty_lock(tty);
3305         }
3306
3307         set_current_state(TASK_RUNNING);
3308         remove_wait_queue(&port->open_wait, &wait);
3309
3310         if (!tty_hung_up_p(filp))
3311                 port->count++;
3312         port->blocked_open--;
3313
3314         if (!retval)
3315                 tty_port_set_active(port, 1);
3316
3317         DBGINFO(("%s block_til_ready ready, rc=%d\n", tty->driver->name, retval));
3318         return retval;
3319 }
3320
3321 /*
3322  * allocate buffers used for calling line discipline receive_buf
3323  * directly in synchronous mode
3324  * note: add 5 bytes to max frame size to allow appending
3325  * 32-bit CRC and status byte when configured to do so
3326  */
3327 static int alloc_tmp_rbuf(struct slgt_info *info)
3328 {
3329         info->tmp_rbuf = kmalloc(info->max_frame_size + 5, GFP_KERNEL);
3330         if (info->tmp_rbuf == NULL)
3331                 return -ENOMEM;
3332         /* unused flag buffer to satisfy receive_buf calling interface */
3333         info->flag_buf = kzalloc(info->max_frame_size + 5, GFP_KERNEL);
3334         if (!info->flag_buf) {
3335                 kfree(info->tmp_rbuf);
3336                 info->tmp_rbuf = NULL;
3337                 return -ENOMEM;
3338         }
3339         return 0;
3340 }
3341
3342 static void free_tmp_rbuf(struct slgt_info *info)
3343 {
3344         kfree(info->tmp_rbuf);
3345         info->tmp_rbuf = NULL;
3346         kfree(info->flag_buf);
3347         info->flag_buf = NULL;
3348 }
3349
3350 /*
3351  * allocate DMA descriptor lists.
3352  */
3353 static int alloc_desc(struct slgt_info *info)
3354 {
3355         unsigned int i;
3356         unsigned int pbufs;
3357
3358         /* allocate memory to hold descriptor lists */
3359         info->bufs = pci_zalloc_consistent(info->pdev, DESC_LIST_SIZE,
3360                                            &info->bufs_dma_addr);
3361         if (info->bufs == NULL)
3362                 return -ENOMEM;
3363
3364         info->rbufs = (struct slgt_desc*)info->bufs;
3365         info->tbufs = ((struct slgt_desc*)info->bufs) + info->rbuf_count;
3366
3367         pbufs = (unsigned int)info->bufs_dma_addr;
3368
3369         /*
3370          * Build circular lists of descriptors
3371          */
3372
3373         for (i=0; i < info->rbuf_count; i++) {
3374                 /* physical address of this descriptor */
3375                 info->rbufs[i].pdesc = pbufs + (i * sizeof(struct slgt_desc));
3376
3377                 /* physical address of next descriptor */
3378                 if (i == info->rbuf_count - 1)
3379                         info->rbufs[i].next = cpu_to_le32(pbufs);
3380                 else
3381                         info->rbufs[i].next = cpu_to_le32(pbufs + ((i+1) * sizeof(struct slgt_desc)));
3382                 set_desc_count(info->rbufs[i], DMABUFSIZE);
3383         }
3384
3385         for (i=0; i < info->tbuf_count; i++) {
3386                 /* physical address of this descriptor */
3387                 info->tbufs[i].pdesc = pbufs + ((info->rbuf_count + i) * sizeof(struct slgt_desc));
3388
3389                 /* physical address of next descriptor */
3390                 if (i == info->tbuf_count - 1)
3391                         info->tbufs[i].next = cpu_to_le32(pbufs + info->rbuf_count * sizeof(struct slgt_desc));
3392                 else
3393                         info->tbufs[i].next = cpu_to_le32(pbufs + ((info->rbuf_count + i + 1) * sizeof(struct slgt_desc)));
3394         }
3395
3396         return 0;
3397 }
3398
3399 static void free_desc(struct slgt_info *info)
3400 {
3401         if (info->bufs != NULL) {
3402                 pci_free_consistent(info->pdev, DESC_LIST_SIZE, info->bufs, info->bufs_dma_addr);
3403                 info->bufs  = NULL;
3404                 info->rbufs = NULL;
3405                 info->tbufs = NULL;
3406         }
3407 }
3408
3409 static int alloc_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count)
3410 {
3411         int i;
3412         for (i=0; i < count; i++) {
3413                 if ((bufs[i].buf = pci_alloc_consistent(info->pdev, DMABUFSIZE, &bufs[i].buf_dma_addr)) == NULL)
3414                         return -ENOMEM;
3415                 bufs[i].pbuf  = cpu_to_le32((unsigned int)bufs[i].buf_dma_addr);
3416         }
3417         return 0;
3418 }
3419
3420 static void free_bufs(struct slgt_info *info, struct slgt_desc *bufs, int count)
3421 {
3422         int i;
3423         for (i=0; i < count; i++) {
3424                 if (bufs[i].buf == NULL)
3425                         continue;
3426                 pci_free_consistent(info->pdev, DMABUFSIZE, bufs[i].buf, bufs[i].buf_dma_addr);
3427                 bufs[i].buf = NULL;
3428         }
3429 }
3430
3431 static int alloc_dma_bufs(struct slgt_info *info)
3432 {
3433         info->rbuf_count = 32;
3434         info->tbuf_count = 32;
3435
3436         if (alloc_desc(info) < 0 ||
3437             alloc_bufs(info, info->rbufs, info->rbuf_count) < 0 ||
3438             alloc_bufs(info, info->tbufs, info->tbuf_count) < 0 ||
3439             alloc_tmp_rbuf(info) < 0) {
3440                 DBGERR(("%s DMA buffer alloc fail\n", info->device_name));
3441                 return -ENOMEM;
3442         }
3443         reset_rbufs(info);
3444         return 0;
3445 }
3446
3447 static void free_dma_bufs(struct slgt_info *info)
3448 {
3449         if (info->bufs) {
3450                 free_bufs(info, info->rbufs, info->rbuf_count);
3451                 free_bufs(info, info->tbufs, info->tbuf_count);
3452                 free_desc(info);
3453         }
3454         free_tmp_rbuf(info);
3455 }
3456
3457 static int claim_resources(struct slgt_info *info)
3458 {
3459         if (request_mem_region(info->phys_reg_addr, SLGT_REG_SIZE, "synclink_gt") == NULL) {
3460                 DBGERR(("%s reg addr conflict, addr=%08X\n",
3461                         info->device_name, info->phys_reg_addr));
3462                 info->init_error = DiagStatus_AddressConflict;
3463                 goto errout;
3464         }
3465         else
3466                 info->reg_addr_requested = true;
3467
3468         info->reg_addr = ioremap_nocache(info->phys_reg_addr, SLGT_REG_SIZE);
3469         if (!info->reg_addr) {
3470                 DBGERR(("%s can't map device registers, addr=%08X\n",
3471                         info->device_name, info->phys_reg_addr));
3472                 info->init_error = DiagStatus_CantAssignPciResources;
3473                 goto errout;
3474         }
3475         return 0;
3476
3477 errout:
3478         release_resources(info);
3479         return -ENODEV;
3480 }
3481
3482 static void release_resources(struct slgt_info *info)
3483 {
3484         if (info->irq_requested) {
3485                 free_irq(info->irq_level, info);
3486                 info->irq_requested = false;
3487         }
3488
3489         if (info->reg_addr_requested) {
3490                 release_mem_region(info->phys_reg_addr, SLGT_REG_SIZE);
3491                 info->reg_addr_requested = false;
3492         }
3493
3494         if (info->reg_addr) {
3495                 iounmap(info->reg_addr);
3496                 info->reg_addr = NULL;
3497         }
3498 }
3499
3500 /* Add the specified device instance data structure to the
3501  * global linked list of devices and increment the device count.
3502  */
3503 static void add_device(struct slgt_info *info)
3504 {
3505         char *devstr;
3506
3507         info->next_device = NULL;
3508         info->line = slgt_device_count;
3509         sprintf(info->device_name, "%s%d", tty_dev_prefix, info->line);
3510
3511         if (info->line < MAX_DEVICES) {
3512                 if (maxframe[info->line])
3513                         info->max_frame_size = maxframe[info->line];
3514         }
3515
3516         slgt_device_count++;
3517
3518         if (!slgt_device_list)
3519                 slgt_device_list = info;
3520         else {
3521                 struct slgt_info *current_dev = slgt_device_list;
3522                 while(current_dev->next_device)
3523                         current_dev = current_dev->next_device;
3524                 current_dev->next_device = info;
3525         }
3526
3527         if (info->max_frame_size < 4096)
3528                 info->max_frame_size = 4096;
3529         else if (info->max_frame_size > 65535)
3530                 info->max_frame_size = 65535;
3531
3532         switch(info->pdev->device) {
3533         case SYNCLINK_GT_DEVICE_ID:
3534                 devstr = "GT";
3535                 break;
3536         case SYNCLINK_GT2_DEVICE_ID:
3537                 devstr = "GT2";
3538                 break;
3539         case SYNCLINK_GT4_DEVICE_ID:
3540                 devstr = "GT4";
3541                 break;
3542         case SYNCLINK_AC_DEVICE_ID:
3543                 devstr = "AC";
3544                 info->params.mode = MGSL_MODE_ASYNC;
3545                 break;
3546         default:
3547                 devstr = "(unknown model)";
3548         }
3549         printk("SyncLink %s %s IO=%08x IRQ=%d MaxFrameSize=%u\n",
3550                 devstr, info->device_name, info->phys_reg_addr,
3551                 info->irq_level, info->max_frame_size);
3552
3553 #if SYNCLINK_GENERIC_HDLC
3554         hdlcdev_init(info);
3555 #endif
3556 }
3557
3558 static const struct tty_port_operations slgt_port_ops = {
3559         .carrier_raised = carrier_raised,
3560         .dtr_rts = dtr_rts,
3561 };
3562
3563 /*
3564  *  allocate device instance structure, return NULL on failure
3565  */
3566 static struct slgt_info *alloc_dev(int adapter_num, int port_num, struct pci_dev *pdev)
3567 {
3568         struct slgt_info *info;
3569
3570         info = kzalloc(sizeof(struct slgt_info), GFP_KERNEL);
3571
3572         if (!info) {
3573                 DBGERR(("%s device alloc failed adapter=%d port=%d\n",
3574                         driver_name, adapter_num, port_num));
3575         } else {
3576                 tty_port_init(&info->port);
3577                 info->port.ops = &slgt_port_ops;
3578                 info->magic = MGSL_MAGIC;
3579                 INIT_WORK(&info->task, bh_handler);
3580                 info->max_frame_size = 4096;
3581                 info->base_clock = 14745600;
3582                 info->rbuf_fill_level = DMABUFSIZE;
3583                 info->port.close_delay = 5*HZ/10;
3584                 info->port.closing_wait = 30*HZ;
3585                 init_waitqueue_head(&info->status_event_wait_q);
3586                 init_waitqueue_head(&info->event_wait_q);
3587                 spin_lock_init(&info->netlock);
3588                 memcpy(&info->params,&default_params,sizeof(MGSL_PARAMS));
3589                 info->idle_mode = HDLC_TXIDLE_FLAGS;
3590                 info->adapter_num = adapter_num;
3591                 info->port_num = port_num;
3592
3593                 setup_timer(&info->tx_timer, tx_timeout, (unsigned long)info);
3594                 setup_timer(&info->rx_timer, rx_timeout, (unsigned long)info);
3595
3596                 /* Copy configuration info to device instance data */
3597                 info->pdev = pdev;
3598                 info->irq_level = pdev->irq;
3599                 info->phys_reg_addr = pci_resource_start(pdev,0);
3600
3601                 info->bus_type = MGSL_BUS_TYPE_PCI;
3602                 info->irq_flags = IRQF_SHARED;
3603
3604                 info->init_error = -1; /* assume error, set to 0 on successful init */
3605         }
3606
3607         return info;
3608 }
3609
3610 static void device_init(int adapter_num, struct pci_dev *pdev)
3611 {
3612         struct slgt_info *port_array[SLGT_MAX_PORTS];
3613         int i;
3614         int port_count = 1;
3615
3616         if (pdev->device == SYNCLINK_GT2_DEVICE_ID)
3617                 port_count = 2;
3618         else if (pdev->device == SYNCLINK_GT4_DEVICE_ID)
3619                 port_count = 4;
3620
3621         /* allocate device instances for all ports */
3622         for (i=0; i < port_count; ++i) {
3623                 port_array[i] = alloc_dev(adapter_num, i, pdev);
3624                 if (port_array[i] == NULL) {
3625                         for (--i; i >= 0; --i) {
3626                                 tty_port_destroy(&port_array[i]->port);
3627                                 kfree(port_array[i]);
3628                         }
3629                         return;
3630                 }
3631         }
3632
3633         /* give copy of port_array to all ports and add to device list  */
3634         for (i=0; i < port_count; ++i) {
3635                 memcpy(port_array[i]->port_array, port_array, sizeof(port_array));
3636                 add_device(port_array[i]);
3637                 port_array[i]->port_count = port_count;
3638                 spin_lock_init(&port_array[i]->lock);
3639         }
3640
3641         /* Allocate and claim adapter resources */
3642         if (!claim_resources(port_array[0])) {
3643
3644                 alloc_dma_bufs(port_array[0]);
3645
3646                 /* copy resource information from first port to others */
3647                 for (i = 1; i < port_count; ++i) {
3648                         port_array[i]->irq_level = port_array[0]->irq_level;
3649                         port_array[i]->reg_addr  = port_array[0]->reg_addr;
3650                         alloc_dma_bufs(port_array[i]);
3651                 }
3652
3653                 if (request_irq(port_array[0]->irq_level,
3654                                         slgt_interrupt,
3655                                         port_array[0]->irq_flags,
3656                                         port_array[0]->device_name,
3657                                         port_array[0]) < 0) {
3658                         DBGERR(("%s request_irq failed IRQ=%d\n",
3659                                 port_array[0]->device_name,
3660                                 port_array[0]->irq_level));
3661                 } else {
3662                         port_array[0]->irq_requested = true;
3663                         adapter_test(port_array[0]);
3664                         for (i=1 ; i < port_count ; i++) {
3665                                 port_array[i]->init_error = port_array[0]->init_error;
3666                                 port_array[i]->gpio_present = port_array[0]->gpio_present;
3667                         }
3668                 }
3669         }
3670
3671         for (i = 0; i < port_count; ++i) {
3672                 struct slgt_info *info = port_array[i];
3673                 tty_port_register_device(&info->port, serial_driver, info->line,
3674                                 &info->pdev->dev);
3675         }
3676 }
3677
3678 static int init_one(struct pci_dev *dev,
3679                               const struct pci_device_id *ent)
3680 {
3681         if (pci_enable_device(dev)) {
3682                 printk("error enabling pci device %p\n", dev);
3683                 return -EIO;
3684         }
3685         pci_set_master(dev);
3686         device_init(slgt_device_count, dev);
3687         return 0;
3688 }
3689
3690 static void remove_one(struct pci_dev *dev)
3691 {
3692 }
3693
3694 static const struct tty_operations ops = {
3695         .open = open,
3696         .close = close,
3697         .write = write,
3698         .put_char = put_char,
3699         .flush_chars = flush_chars,
3700         .write_room = write_room,
3701         .chars_in_buffer = chars_in_buffer,
3702         .flush_buffer = flush_buffer,
3703         .ioctl = ioctl,
3704         .compat_ioctl = slgt_compat_ioctl,
3705         .throttle = throttle,
3706         .unthrottle = unthrottle,
3707         .send_xchar = send_xchar,
3708         .break_ctl = set_break,
3709         .wait_until_sent = wait_until_sent,
3710         .set_termios = set_termios,
3711         .stop = tx_hold,
3712         .start = tx_release,
3713         .hangup = hangup,
3714         .tiocmget = tiocmget,
3715         .tiocmset = tiocmset,
3716         .get_icount = get_icount,
3717         .proc_fops = &synclink_gt_proc_fops,
3718 };
3719
3720 static void slgt_cleanup(void)
3721 {
3722         int rc;
3723         struct slgt_info *info;
3724         struct slgt_info *tmp;
3725
3726         printk(KERN_INFO "unload %s\n", driver_name);
3727
3728         if (serial_driver) {
3729                 for (info=slgt_device_list ; info != NULL ; info=info->next_device)
3730                         tty_unregister_device(serial_driver, info->line);
3731                 rc = tty_unregister_driver(serial_driver);
3732                 if (rc)
3733                         DBGERR(("tty_unregister_driver error=%d\n", rc));
3734                 put_tty_driver(serial_driver);
3735         }
3736
3737         /* reset devices */
3738         info = slgt_device_list;
3739         while(info) {
3740                 reset_port(info);
3741                 info = info->next_device;
3742         }
3743
3744         /* release devices */
3745         info = slgt_device_list;
3746         while(info) {
3747 #if SYNCLINK_GENERIC_HDLC
3748                 hdlcdev_exit(info);
3749 #endif
3750                 free_dma_bufs(info);
3751                 free_tmp_rbuf(info);
3752                 if (info->port_num == 0)
3753                         release_resources(info);
3754                 tmp = info;
3755                 info = info->next_device;
3756                 tty_port_destroy(&tmp->port);
3757                 kfree(tmp);
3758         }
3759
3760         if (pci_registered)
3761                 pci_unregister_driver(&pci_driver);
3762 }
3763
3764 /*
3765  *  Driver initialization entry point.
3766  */
3767 static int __init slgt_init(void)
3768 {
3769         int rc;
3770
3771         printk(KERN_INFO "%s\n", driver_name);
3772
3773         serial_driver = alloc_tty_driver(MAX_DEVICES);
3774         if (!serial_driver) {
3775                 printk("%s can't allocate tty driver\n", driver_name);
3776                 return -ENOMEM;
3777         }
3778
3779         /* Initialize the tty_driver structure */
3780
3781         serial_driver->driver_name = slgt_driver_name;
3782         serial_driver->name = tty_dev_prefix;
3783         serial_driver->major = ttymajor;
3784         serial_driver->minor_start = 64;
3785         serial_driver->type = TTY_DRIVER_TYPE_SERIAL;
3786         serial_driver->subtype = SERIAL_TYPE_NORMAL;
3787         serial_driver->init_termios = tty_std_termios;
3788         serial_driver->init_termios.c_cflag =
3789                 B9600 | CS8 | CREAD | HUPCL | CLOCAL;
3790         serial_driver->init_termios.c_ispeed = 9600;
3791         serial_driver->init_termios.c_ospeed = 9600;
3792         serial_driver->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
3793         tty_set_operations(serial_driver, &ops);
3794         if ((rc = tty_register_driver(serial_driver)) < 0) {
3795                 DBGERR(("%s can't register serial driver\n", driver_name));
3796                 put_tty_driver(serial_driver);
3797                 serial_driver = NULL;
3798                 goto error;
3799         }
3800
3801         printk(KERN_INFO "%s, tty major#%d\n",
3802                driver_name, serial_driver->major);
3803
3804         slgt_device_count = 0;
3805         if ((rc = pci_register_driver(&pci_driver)) < 0) {
3806                 printk("%s pci_register_driver error=%d\n", driver_name, rc);
3807                 goto error;
3808         }
3809         pci_registered = true;
3810
3811         if (!slgt_device_list)
3812                 printk("%s no devices found\n",driver_name);
3813
3814         return 0;
3815
3816 error:
3817         slgt_cleanup();
3818         return rc;
3819 }
3820
3821 static void __exit slgt_exit(void)
3822 {
3823         slgt_cleanup();
3824 }
3825
3826 module_init(slgt_init);
3827 module_exit(slgt_exit);
3828
3829 /*
3830  * register access routines
3831  */
3832
3833 #define CALC_REGADDR() \
3834         unsigned long reg_addr = ((unsigned long)info->reg_addr) + addr; \
3835         if (addr >= 0x80) \
3836                 reg_addr += (info->port_num) * 32; \
3837         else if (addr >= 0x40)  \
3838                 reg_addr += (info->port_num) * 16;
3839
3840 static __u8 rd_reg8(struct slgt_info *info, unsigned int addr)
3841 {
3842         CALC_REGADDR();
3843         return readb((void __iomem *)reg_addr);
3844 }
3845
3846 static void wr_reg8(struct slgt_info *info, unsigned int addr, __u8 value)
3847 {
3848         CALC_REGADDR();
3849         writeb(value, (void __iomem *)reg_addr);
3850 }
3851
3852 static __u16 rd_reg16(struct slgt_info *info, unsigned int addr)
3853 {
3854         CALC_REGADDR();
3855         return readw((void __iomem *)reg_addr);
3856 }
3857
3858 static void wr_reg16(struct slgt_info *info, unsigned int addr, __u16 value)
3859 {
3860         CALC_REGADDR();
3861         writew(value, (void __iomem *)reg_addr);
3862 }
3863
3864 static __u32 rd_reg32(struct slgt_info *info, unsigned int addr)
3865 {
3866         CALC_REGADDR();
3867         return readl((void __iomem *)reg_addr);
3868 }
3869
3870 static void wr_reg32(struct slgt_info *info, unsigned int addr, __u32 value)
3871 {
3872         CALC_REGADDR();
3873         writel(value, (void __iomem *)reg_addr);
3874 }
3875
3876 static void rdma_reset(struct slgt_info *info)
3877 {
3878         unsigned int i;
3879
3880         /* set reset bit */
3881         wr_reg32(info, RDCSR, BIT1);
3882
3883         /* wait for enable bit cleared */
3884         for(i=0 ; i < 1000 ; i++)
3885                 if (!(rd_reg32(info, RDCSR) & BIT0))
3886                         break;
3887 }
3888
3889 static void tdma_reset(struct slgt_info *info)
3890 {
3891         unsigned int i;
3892
3893         /* set reset bit */
3894         wr_reg32(info, TDCSR, BIT1);
3895
3896         /* wait for enable bit cleared */
3897         for(i=0 ; i < 1000 ; i++)
3898                 if (!(rd_reg32(info, TDCSR) & BIT0))
3899                         break;
3900 }
3901
3902 /*
3903  * enable internal loopback
3904  * TxCLK and RxCLK are generated from BRG
3905  * and TxD is looped back to RxD internally.
3906  */
3907 static void enable_loopback(struct slgt_info *info)
3908 {
3909         /* SCR (serial control) BIT2=loopback enable */
3910         wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) | BIT2));
3911
3912         if (info->params.mode != MGSL_MODE_ASYNC) {
3913                 /* CCR (clock control)
3914                  * 07..05  tx clock source (010 = BRG)
3915                  * 04..02  rx clock source (010 = BRG)
3916                  * 01      auxclk enable   (0 = disable)
3917                  * 00      BRG enable      (1 = enable)
3918                  *
3919                  * 0100 1001
3920                  */
3921                 wr_reg8(info, CCR, 0x49);
3922
3923                 /* set speed if available, otherwise use default */
3924                 if (info->params.clock_speed)
3925                         set_rate(info, info->params.clock_speed);
3926                 else
3927                         set_rate(info, 3686400);
3928         }
3929 }
3930
3931 /*
3932  *  set baud rate generator to specified rate
3933  */
3934 static void set_rate(struct slgt_info *info, u32 rate)
3935 {
3936         unsigned int div;
3937         unsigned int osc = info->base_clock;
3938
3939         /* div = osc/rate - 1
3940          *
3941          * Round div up if osc/rate is not integer to
3942          * force to next slowest rate.
3943          */
3944
3945         if (rate) {
3946                 div = osc/rate;
3947                 if (!(osc % rate) && div)
3948                         div--;
3949                 wr_reg16(info, BDR, (unsigned short)div);
3950         }
3951 }
3952
3953 static void rx_stop(struct slgt_info *info)
3954 {
3955         unsigned short val;
3956
3957         /* disable and reset receiver */
3958         val = rd_reg16(info, RCR) & ~BIT1;          /* clear enable bit */
3959         wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */
3960         wr_reg16(info, RCR, val);                  /* clear reset bit */
3961
3962         slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA + IRQ_RXIDLE);
3963
3964         /* clear pending rx interrupts */
3965         wr_reg16(info, SSR, IRQ_RXIDLE + IRQ_RXOVER);
3966
3967         rdma_reset(info);
3968
3969         info->rx_enabled = false;
3970         info->rx_restart = false;
3971 }
3972
3973 static void rx_start(struct slgt_info *info)
3974 {
3975         unsigned short val;
3976
3977         slgt_irq_off(info, IRQ_RXOVER + IRQ_RXDATA);
3978
3979         /* clear pending rx overrun IRQ */
3980         wr_reg16(info, SSR, IRQ_RXOVER);
3981
3982         /* reset and disable receiver */
3983         val = rd_reg16(info, RCR) & ~BIT1; /* clear enable bit */
3984         wr_reg16(info, RCR, (unsigned short)(val | BIT2)); /* set reset bit */
3985         wr_reg16(info, RCR, val);                  /* clear reset bit */
3986
3987         rdma_reset(info);
3988         reset_rbufs(info);
3989
3990         if (info->rx_pio) {
3991                 /* rx request when rx FIFO not empty */
3992                 wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) & ~BIT14));
3993                 slgt_irq_on(info, IRQ_RXDATA);
3994                 if (info->params.mode == MGSL_MODE_ASYNC) {
3995                         /* enable saving of rx status */
3996                         wr_reg32(info, RDCSR, BIT6);
3997                 }
3998         } else {
3999                 /* rx request when rx FIFO half full */
4000                 wr_reg16(info, SCR, (unsigned short)(rd_reg16(info, SCR) | BIT14));
4001                 /* set 1st descriptor address */
4002                 wr_reg32(info, RDDAR, info->rbufs[0].pdesc);
4003
4004                 if (info->params.mode != MGSL_MODE_ASYNC) {
4005                         /* enable rx DMA and DMA interrupt */
4006                         wr_reg32(info, RDCSR, (BIT2 + BIT0));
4007                 } else {
4008                         /* enable saving of rx status, rx DMA and DMA interrupt */
4009                         wr_reg32(info, RDCSR, (BIT6 + BIT2 + BIT0));
4010                 }
4011         }
4012
4013         slgt_irq_on(info, IRQ_RXOVER);
4014
4015         /* enable receiver */
4016         wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | BIT1));
4017
4018         info->rx_restart = false;
4019         info->rx_enabled = true;
4020 }
4021
4022 static void tx_start(struct slgt_info *info)
4023 {
4024         if (!info->tx_enabled) {
4025                 wr_reg16(info, TCR,
4026                          (unsigned short)((rd_reg16(info, TCR) | BIT1) & ~BIT2));
4027                 info->tx_enabled = true;
4028         }
4029
4030         if (desc_count(info->tbufs[info->tbuf_start])) {
4031                 info->drop_rts_on_tx_done = false;
4032
4033                 if (info->params.mode != MGSL_MODE_ASYNC) {
4034                         if (info->params.flags & HDLC_FLAG_AUTO_RTS) {
4035                                 get_signals(info);
4036                                 if (!(info->signals & SerialSignal_RTS)) {
4037                                         info->signals |= SerialSignal_RTS;
4038                                         set_signals(info);
4039                                         info->drop_rts_on_tx_done = true;
4040                                 }
4041                         }
4042
4043                         slgt_irq_off(info, IRQ_TXDATA);
4044                         slgt_irq_on(info, IRQ_TXUNDER + IRQ_TXIDLE);
4045                         /* clear tx idle and underrun status bits */
4046                         wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER));
4047                 } else {
4048                         slgt_irq_off(info, IRQ_TXDATA);
4049                         slgt_irq_on(info, IRQ_TXIDLE);
4050                         /* clear tx idle status bit */
4051                         wr_reg16(info, SSR, IRQ_TXIDLE);
4052                 }
4053                 /* set 1st descriptor address and start DMA */
4054                 wr_reg32(info, TDDAR, info->tbufs[info->tbuf_start].pdesc);
4055                 wr_reg32(info, TDCSR, BIT2 + BIT0);
4056                 info->tx_active = true;
4057         }
4058 }
4059
4060 static void tx_stop(struct slgt_info *info)
4061 {
4062         unsigned short val;
4063
4064         del_timer(&info->tx_timer);
4065
4066         tdma_reset(info);
4067
4068         /* reset and disable transmitter */
4069         val = rd_reg16(info, TCR) & ~BIT1;          /* clear enable bit */
4070         wr_reg16(info, TCR, (unsigned short)(val | BIT2)); /* set reset bit */
4071
4072         slgt_irq_off(info, IRQ_TXDATA + IRQ_TXIDLE + IRQ_TXUNDER);
4073
4074         /* clear tx idle and underrun status bit */
4075         wr_reg16(info, SSR, (unsigned short)(IRQ_TXIDLE + IRQ_TXUNDER));
4076
4077         reset_tbufs(info);
4078
4079         info->tx_enabled = false;
4080         info->tx_active = false;
4081 }
4082
4083 static void reset_port(struct slgt_info *info)
4084 {
4085         if (!info->reg_addr)
4086                 return;
4087
4088         tx_stop(info);
4089         rx_stop(info);
4090
4091         info->signals &= ~(SerialSignal_RTS | SerialSignal_DTR);
4092         set_signals(info);
4093
4094         slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
4095 }
4096
4097 static void reset_adapter(struct slgt_info *info)
4098 {
4099         int i;
4100         for (i=0; i < info->port_count; ++i) {
4101                 if (info->port_array[i])
4102                         reset_port(info->port_array[i]);
4103         }
4104 }
4105
4106 static void async_mode(struct slgt_info *info)
4107 {
4108         unsigned short val;
4109
4110         slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
4111         tx_stop(info);
4112         rx_stop(info);
4113
4114         /* TCR (tx control)
4115          *
4116          * 15..13  mode, 010=async
4117          * 12..10  encoding, 000=NRZ
4118          * 09      parity enable
4119          * 08      1=odd parity, 0=even parity
4120          * 07      1=RTS driver control
4121          * 06      1=break enable
4122          * 05..04  character length
4123          *         00=5 bits
4124          *         01=6 bits
4125          *         10=7 bits
4126          *         11=8 bits
4127          * 03      0=1 stop bit, 1=2 stop bits
4128          * 02      reset
4129          * 01      enable
4130          * 00      auto-CTS enable
4131          */
4132         val = 0x4000;
4133
4134         if (info->if_mode & MGSL_INTERFACE_RTS_EN)
4135                 val |= BIT7;
4136
4137         if (info->params.parity != ASYNC_PARITY_NONE) {
4138                 val |= BIT9;
4139                 if (info->params.parity == ASYNC_PARITY_ODD)
4140                         val |= BIT8;
4141         }
4142
4143         switch (info->params.data_bits)
4144         {
4145         case 6: val |= BIT4; break;
4146         case 7: val |= BIT5; break;
4147         case 8: val |= BIT5 + BIT4; break;
4148         }
4149
4150         if (info->params.stop_bits != 1)
4151                 val |= BIT3;
4152
4153         if (info->params.flags & HDLC_FLAG_AUTO_CTS)
4154                 val |= BIT0;
4155
4156         wr_reg16(info, TCR, val);
4157
4158         /* RCR (rx control)
4159          *
4160          * 15..13  mode, 010=async
4161          * 12..10  encoding, 000=NRZ
4162          * 09      parity enable
4163          * 08      1=odd parity, 0=even parity
4164          * 07..06  reserved, must be 0
4165          * 05..04  character length
4166          *         00=5 bits
4167          *         01=6 bits
4168          *         10=7 bits
4169          *         11=8 bits
4170          * 03      reserved, must be zero
4171          * 02      reset
4172          * 01      enable
4173          * 00      auto-DCD enable
4174          */
4175         val = 0x4000;
4176
4177         if (info->params.parity != ASYNC_PARITY_NONE) {
4178                 val |= BIT9;
4179                 if (info->params.parity == ASYNC_PARITY_ODD)
4180                         val |= BIT8;
4181         }
4182
4183         switch (info->params.data_bits)
4184         {
4185         case 6: val |= BIT4; break;
4186         case 7: val |= BIT5; break;
4187         case 8: val |= BIT5 + BIT4; break;
4188         }
4189
4190         if (info->params.flags & HDLC_FLAG_AUTO_DCD)
4191                 val |= BIT0;
4192
4193         wr_reg16(info, RCR, val);
4194
4195         /* CCR (clock control)
4196          *
4197          * 07..05  011 = tx clock source is BRG/16
4198          * 04..02  010 = rx clock source is BRG
4199          * 01      0 = auxclk disabled
4200          * 00      1 = BRG enabled
4201          *
4202          * 0110 1001
4203          */
4204         wr_reg8(info, CCR, 0x69);
4205
4206         msc_set_vcr(info);
4207
4208         /* SCR (serial control)
4209          *
4210          * 15  1=tx req on FIFO half empty
4211          * 14  1=rx req on FIFO half full
4212          * 13  tx data  IRQ enable
4213          * 12  tx idle  IRQ enable
4214          * 11  rx break on IRQ enable
4215          * 10  rx data  IRQ enable
4216          * 09  rx break off IRQ enable
4217          * 08  overrun  IRQ enable
4218          * 07  DSR      IRQ enable
4219          * 06  CTS      IRQ enable
4220          * 05  DCD      IRQ enable
4221          * 04  RI       IRQ enable
4222          * 03  0=16x sampling, 1=8x sampling
4223          * 02  1=txd->rxd internal loopback enable
4224          * 01  reserved, must be zero
4225          * 00  1=master IRQ enable
4226          */
4227         val = BIT15 + BIT14 + BIT0;
4228         /* JCR[8] : 1 = x8 async mode feature available */
4229         if ((rd_reg32(info, JCR) & BIT8) && info->params.data_rate &&
4230             ((info->base_clock < (info->params.data_rate * 16)) ||
4231              (info->base_clock % (info->params.data_rate * 16)))) {
4232                 /* use 8x sampling */
4233                 val |= BIT3;
4234                 set_rate(info, info->params.data_rate * 8);
4235         } else {
4236                 /* use 16x sampling */
4237                 set_rate(info, info->params.data_rate * 16);
4238         }
4239         wr_reg16(info, SCR, val);
4240
4241         slgt_irq_on(info, IRQ_RXBREAK | IRQ_RXOVER);
4242
4243         if (info->params.loopback)
4244                 enable_loopback(info);
4245 }
4246
4247 static void sync_mode(struct slgt_info *info)
4248 {
4249         unsigned short val;
4250
4251         slgt_irq_off(info, IRQ_ALL | IRQ_MASTER);
4252         tx_stop(info);
4253         rx_stop(info);
4254
4255         /* TCR (tx control)
4256          *
4257          * 15..13  mode
4258          *         000=HDLC/SDLC
4259          *         001=raw bit synchronous
4260          *         010=asynchronous/isochronous
4261          *         011=monosync byte synchronous
4262          *         100=bisync byte synchronous
4263          *         101=xsync byte synchronous
4264          * 12..10  encoding
4265          * 09      CRC enable
4266          * 08      CRC32
4267          * 07      1=RTS driver control
4268          * 06      preamble enable
4269          * 05..04  preamble length
4270          * 03      share open/close flag
4271          * 02      reset
4272          * 01      enable
4273          * 00      auto-CTS enable
4274          */
4275         val = BIT2;
4276
4277         switch(info->params.mode) {
4278         case MGSL_MODE_XSYNC:
4279                 val |= BIT15 + BIT13;
4280                 break;
4281         case MGSL_MODE_MONOSYNC: val |= BIT14 + BIT13; break;
4282         case MGSL_MODE_BISYNC:   val |= BIT15; break;
4283         case MGSL_MODE_RAW:      val |= BIT13; break;
4284         }
4285         if (info->if_mode & MGSL_INTERFACE_RTS_EN)
4286                 val |= BIT7;
4287
4288         switch(info->params.encoding)
4289         {
4290         case HDLC_ENCODING_NRZB:          val |= BIT10; break;
4291         case HDLC_ENCODING_NRZI_MARK:     val |= BIT11; break;
4292         case HDLC_ENCODING_NRZI:          val |= BIT11 + BIT10; break;
4293         case HDLC_ENCODING_BIPHASE_MARK:  val |= BIT12; break;
4294         case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break;
4295         case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break;
4296         case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break;
4297         }
4298
4299         switch (info->params.crc_type & HDLC_CRC_MASK)
4300         {
4301         case HDLC_CRC_16_CCITT: val |= BIT9; break;
4302         case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break;
4303         }
4304
4305         if (info->params.preamble != HDLC_PREAMBLE_PATTERN_NONE)
4306                 val |= BIT6;
4307
4308         switch (info->params.preamble_length)
4309         {
4310         case HDLC_PREAMBLE_LENGTH_16BITS: val |= BIT5; break;
4311         case HDLC_PREAMBLE_LENGTH_32BITS: val |= BIT4; break;
4312         case HDLC_PREAMBLE_LENGTH_64BITS: val |= BIT5 + BIT4; break;
4313         }
4314
4315         if (info->params.flags & HDLC_FLAG_AUTO_CTS)
4316                 val |= BIT0;
4317
4318         wr_reg16(info, TCR, val);
4319
4320         /* TPR (transmit preamble) */
4321
4322         switch (info->params.preamble)
4323         {
4324         case HDLC_PREAMBLE_PATTERN_FLAGS: val = 0x7e; break;
4325         case HDLC_PREAMBLE_PATTERN_ONES:  val = 0xff; break;
4326         case HDLC_PREAMBLE_PATTERN_ZEROS: val = 0x00; break;
4327         case HDLC_PREAMBLE_PATTERN_10:    val = 0x55; break;
4328         case HDLC_PREAMBLE_PATTERN_01:    val = 0xaa; break;
4329         default:                          val = 0x7e; break;
4330         }
4331         wr_reg8(info, TPR, (unsigned char)val);
4332
4333         /* RCR (rx control)
4334          *
4335          * 15..13  mode
4336          *         000=HDLC/SDLC
4337          *         001=raw bit synchronous
4338          *         010=asynchronous/isochronous
4339          *         011=monosync byte synchronous
4340          *         100=bisync byte synchronous
4341          *         101=xsync byte synchronous
4342          * 12..10  encoding
4343          * 09      CRC enable
4344          * 08      CRC32
4345          * 07..03  reserved, must be 0
4346          * 02      reset
4347          * 01      enable
4348          * 00      auto-DCD enable
4349          */
4350         val = 0;
4351
4352         switch(info->params.mode) {
4353         case MGSL_MODE_XSYNC:
4354                 val |= BIT15 + BIT13;
4355                 break;
4356         case MGSL_MODE_MONOSYNC: val |= BIT14 + BIT13; break;
4357         case MGSL_MODE_BISYNC:   val |= BIT15; break;
4358         case MGSL_MODE_RAW:      val |= BIT13; break;
4359         }
4360
4361         switch(info->params.encoding)
4362         {
4363         case HDLC_ENCODING_NRZB:          val |= BIT10; break;
4364         case HDLC_ENCODING_NRZI_MARK:     val |= BIT11; break;
4365         case HDLC_ENCODING_NRZI:          val |= BIT11 + BIT10; break;
4366         case HDLC_ENCODING_BIPHASE_MARK:  val |= BIT12; break;
4367         case HDLC_ENCODING_BIPHASE_SPACE: val |= BIT12 + BIT10; break;
4368         case HDLC_ENCODING_BIPHASE_LEVEL: val |= BIT12 + BIT11; break;
4369         case HDLC_ENCODING_DIFF_BIPHASE_LEVEL: val |= BIT12 + BIT11 + BIT10; break;
4370         }
4371
4372         switch (info->params.crc_type & HDLC_CRC_MASK)
4373         {
4374         case HDLC_CRC_16_CCITT: val |= BIT9; break;
4375         case HDLC_CRC_32_CCITT: val |= BIT9 + BIT8; break;
4376         }
4377
4378         if (info->params.flags & HDLC_FLAG_AUTO_DCD)
4379                 val |= BIT0;
4380
4381         wr_reg16(info, RCR, val);
4382
4383         /* CCR (clock control)
4384          *
4385          * 07..05  tx clock source
4386          * 04..02  rx clock source
4387          * 01      auxclk enable
4388          * 00      BRG enable
4389          */
4390         val = 0;
4391
4392         if (info->params.flags & HDLC_FLAG_TXC_BRG)
4393         {
4394                 // when RxC source is DPLL, BRG generates 16X DPLL
4395                 // reference clock, so take TxC from BRG/16 to get
4396                 // transmit clock at actual data rate
4397                 if (info->params.flags & HDLC_FLAG_RXC_DPLL)
4398                         val |= BIT6 + BIT5;     /* 011, txclk = BRG/16 */
4399                 else
4400                         val |= BIT6;    /* 010, txclk = BRG */
4401         }
4402         else if (info->params.flags & HDLC_FLAG_TXC_DPLL)
4403                 val |= BIT7;    /* 100, txclk = DPLL Input */
4404         else if (info->params.flags & HDLC_FLAG_TXC_RXCPIN)
4405                 val |= BIT5;    /* 001, txclk = RXC Input */
4406
4407         if (info->params.flags & HDLC_FLAG_RXC_BRG)
4408                 val |= BIT3;    /* 010, rxclk = BRG */
4409         else if (info->params.flags & HDLC_FLAG_RXC_DPLL)
4410                 val |= BIT4;    /* 100, rxclk = DPLL */
4411         else if (info->params.flags & HDLC_FLAG_RXC_TXCPIN)
4412                 val |= BIT2;    /* 001, rxclk = TXC Input */
4413
4414         if (info->params.clock_speed)
4415                 val |= BIT1 + BIT0;
4416
4417         wr_reg8(info, CCR, (unsigned char)val);
4418
4419         if (info->params.flags & (HDLC_FLAG_TXC_DPLL + HDLC_FLAG_RXC_DPLL))
4420         {
4421                 // program DPLL mode
4422                 switch(info->params.encoding)
4423                 {
4424                 case HDLC_ENCODING_BIPHASE_MARK:
4425                 case HDLC_ENCODING_BIPHASE_SPACE:
4426                         val = BIT7; break;
4427                 case HDLC_ENCODING_BIPHASE_LEVEL:
4428                 case HDLC_ENCODING_DIFF_BIPHASE_LEVEL:
4429                         val = BIT7 + BIT6; break;
4430                 default: val = BIT6;    // NRZ encodings
4431                 }
4432                 wr_reg16(info, RCR, (unsigned short)(rd_reg16(info, RCR) | val));
4433
4434                 // DPLL requires a 16X reference clock from BRG
4435                 set_rate(info, info->params.clock_speed * 16);
4436         }
4437         else
4438                 set_rate(info, info->params.clock_speed);
4439
4440         tx_set_idle(info);
4441
4442         msc_set_vcr(info);
4443
4444         /* SCR (serial control)
4445          *
4446          * 15  1=tx req on FIFO half empty
4447          * 14  1=rx req on FIFO half full
4448          * 13  tx data  IRQ enable
4449          * 12  tx idle  IRQ enable
4450          * 11  underrun IRQ enable
4451          * 10  rx data  IRQ enable
4452          * 09  rx idle  IRQ enable
4453          * 08  overrun  IRQ enable
4454          * 07  DSR      IRQ enable
4455          * 06  CTS      IRQ enable
4456          * 05  DCD      IRQ enable
4457          * 04  RI       IRQ enable
4458          * 03  reserved, must be zero
4459          * 02  1=txd->rxd internal loopback enable
4460          * 01  reserved, must be zero
4461          * 00  1=master IRQ enable
4462          */
4463         wr_reg16(info, SCR, BIT15 + BIT14 + BIT0);
4464
4465         if (info->params.loopback)
4466                 enable_loopback(info);
4467 }
4468
4469 /*
4470  *  set transmit idle mode
4471  */
4472 static void tx_set_idle(struct slgt_info *info)
4473 {
4474         unsigned char val;
4475         unsigned short tcr;
4476
4477         /* if preamble enabled (tcr[6] == 1) then tx idle size = 8 bits
4478          * else tcr[5:4] = tx idle size: 00 = 8 bits, 01 = 16 bits
4479          */
4480         tcr = rd_reg16(info, TCR);
4481         if (info->idle_mode & HDLC_TXIDLE_CUSTOM_16) {
4482                 /* disable preamble, set idle size to 16 bits */
4483                 tcr = (tcr & ~(BIT6 + BIT5)) | BIT4;
4484                 /* MSB of 16 bit idle specified in tx preamble register (TPR) */
4485                 wr_reg8(info, TPR, (unsigned char)((info->idle_mode >> 8) & 0xff));
4486         } else if (!(tcr & BIT6)) {
4487                 /* preamble is disabled, set idle size to 8 bits */
4488                 tcr &= ~(BIT5 + BIT4);
4489         }
4490         wr_reg16(info, TCR, tcr);
4491
4492         if (info->idle_mode & (HDLC_TXIDLE_CUSTOM_8 | HDLC_TXIDLE_CUSTOM_16)) {
4493                 /* LSB of custom tx idle specified in tx idle register */
4494                 val = (unsigned char)(info->idle_mode & 0xff);
4495         } else {
4496                 /* standard 8 bit idle patterns */
4497                 switch(info->idle_mode)
4498                 {
4499                 case HDLC_TXIDLE_FLAGS:          val = 0x7e; break;
4500                 case HDLC_TXIDLE_ALT_ZEROS_ONES:
4501                 case HDLC_TXIDLE_ALT_MARK_SPACE: val = 0xaa; break;
4502                 case HDLC_TXIDLE_ZEROS:
4503                 case HDLC_TXIDLE_SPACE:          val = 0x00; break;
4504                 default:                         val = 0xff;
4505                 }
4506         }
4507
4508         wr_reg8(info, TIR, val);
4509 }
4510
4511 /*
4512  * get state of V24 status (input) signals
4513  */
4514 static void get_signals(struct slgt_info *info)
4515 {
4516         unsigned short status = rd_reg16(info, SSR);
4517
4518         /* clear all serial signals except RTS and DTR */
4519         info->signals &= SerialSignal_RTS | SerialSignal_DTR;
4520
4521         if (status & BIT3)
4522                 info->signals |= SerialSignal_DSR;
4523         if (status & BIT2)
4524                 info->signals |= SerialSignal_CTS;
4525         if (status & BIT1)
4526                 info->signals |= SerialSignal_DCD;
4527         if (status & BIT0)
4528                 info->signals |= SerialSignal_RI;
4529 }
4530
4531 /*
4532  * set V.24 Control Register based on current configuration
4533  */
4534 static void msc_set_vcr(struct slgt_info *info)
4535 {
4536         unsigned char val = 0;
4537
4538         /* VCR (V.24 control)
4539          *
4540          * 07..04  serial IF select
4541          * 03      DTR
4542          * 02      RTS
4543          * 01      LL
4544          * 00      RL
4545          */
4546
4547         switch(info->if_mode & MGSL_INTERFACE_MASK)
4548         {
4549         case MGSL_INTERFACE_RS232:
4550                 val |= BIT5; /* 0010 */
4551                 break;
4552         case MGSL_INTERFACE_V35:
4553                 val |= BIT7 + BIT6 + BIT5; /* 1110 */
4554                 break;
4555         case MGSL_INTERFACE_RS422:
4556                 val |= BIT6; /* 0100 */
4557                 break;
4558         }
4559
4560         if (info->if_mode & MGSL_INTERFACE_MSB_FIRST)
4561                 val |= BIT4;
4562         if (info->signals & SerialSignal_DTR)
4563                 val |= BIT3;
4564         if (info->signals & SerialSignal_RTS)
4565                 val |= BIT2;
4566         if (info->if_mode & MGSL_INTERFACE_LL)
4567                 val |= BIT1;
4568         if (info->if_mode & MGSL_INTERFACE_RL)
4569                 val |= BIT0;
4570         wr_reg8(info, VCR, val);
4571 }
4572
4573 /*
4574  * set state of V24 control (output) signals
4575  */
4576 static void set_signals(struct slgt_info *info)
4577 {
4578         unsigned char val = rd_reg8(info, VCR);
4579         if (info->signals & SerialSignal_DTR)
4580                 val |= BIT3;
4581         else
4582                 val &= ~BIT3;
4583         if (info->signals & SerialSignal_RTS)
4584                 val |= BIT2;
4585         else
4586                 val &= ~BIT2;
4587         wr_reg8(info, VCR, val);
4588 }
4589
4590 /*
4591  * free range of receive DMA buffers (i to last)
4592  */
4593 static void free_rbufs(struct slgt_info *info, unsigned int i, unsigned int last)
4594 {
4595         int done = 0;
4596
4597         while(!done) {
4598                 /* reset current buffer for reuse */
4599                 info->rbufs[i].status = 0;
4600                 set_desc_count(info->rbufs[i], info->rbuf_fill_level);
4601                 if (i == last)
4602                         done = 1;
4603                 if (++i == info->rbuf_count)
4604                         i = 0;
4605         }
4606         info->rbuf_current = i;
4607 }
4608
4609 /*
4610  * mark all receive DMA buffers as free
4611  */
4612 static void reset_rbufs(struct slgt_info *info)
4613 {
4614         free_rbufs(info, 0, info->rbuf_count - 1);
4615         info->rbuf_fill_index = 0;
4616         info->rbuf_fill_count = 0;
4617 }
4618
4619 /*
4620  * pass receive HDLC frame to upper layer
4621  *
4622  * return true if frame available, otherwise false
4623  */
4624 static bool rx_get_frame(struct slgt_info *info)
4625 {
4626         unsigned int start, end;
4627         unsigned short status;
4628         unsigned int framesize = 0;
4629         unsigned long flags;
4630         struct tty_struct *tty = info->port.tty;
4631         unsigned char addr_field = 0xff;
4632         unsigned int crc_size = 0;
4633
4634         switch (info->params.crc_type & HDLC_CRC_MASK) {
4635         case HDLC_CRC_16_CCITT: crc_size = 2; break;
4636         case HDLC_CRC_32_CCITT: crc_size = 4; break;
4637         }
4638
4639 check_again:
4640
4641         framesize = 0;
4642         addr_field = 0xff;
4643         start = end = info->rbuf_current;
4644
4645         for (;;) {
4646                 if (!desc_complete(info->rbufs[end]))
4647                         goto cleanup;
4648
4649                 if (framesize == 0 && info->params.addr_filter != 0xff)
4650                         addr_field = info->rbufs[end].buf[0];
4651
4652                 framesize += desc_count(info->rbufs[end]);
4653
4654                 if (desc_eof(info->rbufs[end]))
4655                         break;
4656
4657                 if (++end == info->rbuf_count)
4658                         end = 0;
4659
4660                 if (end == info->rbuf_current) {
4661                         if (info->rx_enabled){
4662                                 spin_lock_irqsave(&info->lock,flags);
4663                                 rx_start(info);
4664                                 spin_unlock_irqrestore(&info->lock,flags);
4665                         }
4666                         goto cleanup;
4667                 }
4668         }
4669
4670         /* status
4671          *
4672          * 15      buffer complete
4673          * 14..06  reserved
4674          * 05..04  residue
4675          * 02      eof (end of frame)
4676          * 01      CRC error
4677          * 00      abort
4678          */
4679         status = desc_status(info->rbufs[end]);
4680
4681         /* ignore CRC bit if not using CRC (bit is undefined) */
4682         if ((info->params.crc_type & HDLC_CRC_MASK) == HDLC_CRC_NONE)
4683                 status &= ~BIT1;
4684
4685         if (framesize == 0 ||
4686                  (addr_field != 0xff && addr_field != info->params.addr_filter)) {
4687                 free_rbufs(info, start, end);
4688                 goto check_again;
4689         }
4690
4691         if (framesize < (2 + crc_size) || status & BIT0) {
4692                 info->icount.rxshort++;
4693                 framesize = 0;
4694         } else if (status & BIT1) {
4695                 info->icount.rxcrc++;
4696                 if (!(info->params.crc_type & HDLC_CRC_RETURN_EX))
4697                         framesize = 0;
4698         }
4699
4700 #if SYNCLINK_GENERIC_HDLC
4701         if (framesize == 0) {
4702                 info->netdev->stats.rx_errors++;
4703                 info->netdev->stats.rx_frame_errors++;
4704         }
4705 #endif
4706
4707         DBGBH(("%s rx frame status=%04X size=%d\n",
4708                 info->device_name, status, framesize));
4709         DBGDATA(info, info->rbufs[start].buf, min_t(int, framesize, info->rbuf_fill_level), "rx");
4710
4711         if (framesize) {
4712                 if (!(info->params.crc_type & HDLC_CRC_RETURN_EX)) {
4713                         framesize -= crc_size;
4714                         crc_size = 0;
4715                 }
4716
4717                 if (framesize > info->max_frame_size + crc_size)
4718                         info->icount.rxlong++;
4719                 else {
4720                         /* copy dma buffer(s) to contiguous temp buffer */
4721                         int copy_count = framesize;
4722                         int i = start;
4723                         unsigned char *p = info->tmp_rbuf;
4724                         info->tmp_rbuf_count = framesize;
4725
4726                         info->icount.rxok++;
4727
4728                         while(copy_count) {
4729                                 int partial_count = min_t(int, copy_count, info->rbuf_fill_level);
4730                                 memcpy(p, info->rbufs[i].buf, partial_count);
4731                                 p += partial_count;
4732                                 copy_count -= partial_count;
4733                                 if (++i == info->rbuf_count)
4734                                         i = 0;
4735                         }
4736
4737                         if (info->params.crc_type & HDLC_CRC_RETURN_EX) {
4738                                 *p = (status & BIT1) ? RX_CRC_ERROR : RX_OK;
4739                                 framesize++;
4740                         }
4741
4742 #if SYNCLINK_GENERIC_HDLC
4743                         if (info->netcount)
4744                                 hdlcdev_rx(info,info->tmp_rbuf, framesize);
4745                         else
4746 #endif
4747                                 ldisc_receive_buf(tty, info->tmp_rbuf, info->flag_buf, framesize);
4748                 }
4749         }
4750         free_rbufs(info, start, end);
4751         return true;
4752
4753 cleanup:
4754         return false;
4755 }
4756
4757 /*
4758  * pass receive buffer (RAW synchronous mode) to tty layer
4759  * return true if buffer available, otherwise false
4760  */
4761 static bool rx_get_buf(struct slgt_info *info)
4762 {
4763         unsigned int i = info->rbuf_current;
4764         unsigned int count;
4765
4766         if (!desc_complete(info->rbufs[i]))
4767                 return false;
4768         count = desc_count(info->rbufs[i]);
4769         switch(info->params.mode) {
4770         case MGSL_MODE_MONOSYNC:
4771         case MGSL_MODE_BISYNC:
4772         case MGSL_MODE_XSYNC:
4773                 /* ignore residue in byte synchronous modes */
4774                 if (desc_residue(info->rbufs[i]))
4775                         count--;
4776                 break;
4777         }
4778         DBGDATA(info, info->rbufs[i].buf, count, "rx");
4779         DBGINFO(("rx_get_buf size=%d\n", count));
4780         if (count)
4781                 ldisc_receive_buf(info->port.tty, info->rbufs[i].buf,
4782                                   info->flag_buf, count);
4783         free_rbufs(info, i, i);
4784         return true;
4785 }
4786
4787 static void reset_tbufs(struct slgt_info *info)
4788 {
4789         unsigned int i;
4790         info->tbuf_current = 0;
4791         for (i=0 ; i < info->tbuf_count ; i++) {
4792                 info->tbufs[i].status = 0;
4793                 info->tbufs[i].count  = 0;
4794         }
4795 }
4796
4797 /*
4798  * return number of free transmit DMA buffers
4799  */
4800 static unsigned int free_tbuf_count(struct slgt_info *info)
4801 {
4802         unsigned int count = 0;
4803         unsigned int i = info->tbuf_current;
4804
4805         do
4806         {
4807                 if (desc_count(info->tbufs[i]))
4808                         break; /* buffer in use */
4809                 ++count;
4810                 if (++i == info->tbuf_count)
4811                         i=0;
4812         } while (i != info->tbuf_current);
4813
4814         /* if tx DMA active, last zero count buffer is in use */
4815         if (count && (rd_reg32(info, TDCSR) & BIT0))
4816                 --count;
4817
4818         return count;
4819 }
4820
4821 /*
4822  * return number of bytes in unsent transmit DMA buffers
4823  * and the serial controller tx FIFO
4824  */
4825 static unsigned int tbuf_bytes(struct slgt_info *info)
4826 {
4827         unsigned int total_count = 0;
4828         unsigned int i = info->tbuf_current;
4829         unsigned int reg_value;
4830         unsigned int count;
4831         unsigned int active_buf_count = 0;
4832
4833         /*
4834          * Add descriptor counts for all tx DMA buffers.
4835          * If count is zero (cleared by DMA controller after read),
4836          * the buffer is complete or is actively being read from.
4837          *
4838          * Record buf_count of last buffer with zero count starting
4839          * from current ring position. buf_count is mirror
4840          * copy of count and is not cleared by serial controller.
4841          * If DMA controller is active, that buffer is actively
4842          * being read so add to total.
4843          */
4844         do {
4845                 count = desc_count(info->tbufs[i]);
4846                 if (count)
4847                         total_count += count;
4848                 else if (!total_count)
4849                         active_buf_count = info->tbufs[i].buf_count;
4850                 if (++i == info->tbuf_count)
4851                         i = 0;
4852         } while (i != info->tbuf_current);
4853
4854         /* read tx DMA status register */
4855         reg_value = rd_reg32(info, TDCSR);
4856
4857         /* if tx DMA active, last zero count buffer is in use */
4858         if (reg_value & BIT0)
4859                 total_count += active_buf_count;
4860
4861         /* add tx FIFO count = reg_value[15..8] */
4862         total_count += (reg_value >> 8) & 0xff;
4863
4864         /* if transmitter active add one byte for shift register */
4865         if (info->tx_active)
4866                 total_count++;
4867
4868         return total_count;
4869 }
4870
4871 /*
4872  * load data into transmit DMA buffer ring and start transmitter if needed
4873  * return true if data accepted, otherwise false (buffers full)
4874  */
4875 static bool tx_load(struct slgt_info *info, const char *buf, unsigned int size)
4876 {
4877         unsigned short count;
4878         unsigned int i;
4879         struct slgt_desc *d;
4880
4881         /* check required buffer space */
4882         if (DIV_ROUND_UP(size, DMABUFSIZE) > free_tbuf_count(info))
4883                 return false;
4884
4885         DBGDATA(info, buf, size, "tx");
4886
4887         /*
4888          * copy data to one or more DMA buffers in circular ring
4889          * tbuf_start   = first buffer for this data
4890          * tbuf_current = next free buffer
4891          *
4892          * Copy all data before making data visible to DMA controller by
4893          * setting descriptor count of the first buffer.
4894          * This prevents an active DMA controller from reading the first DMA
4895          * buffers of a frame and stopping before the final buffers are filled.
4896          */
4897
4898         info->tbuf_start = i = info->tbuf_current;
4899
4900         while (size) {
4901                 d = &info->tbufs[i];
4902
4903                 count = (unsigned short)((size > DMABUFSIZE) ? DMABUFSIZE : size);
4904                 memcpy(d->buf, buf, count);
4905
4906                 size -= count;
4907                 buf  += count;
4908
4909                 /*
4910                  * set EOF bit for last buffer of HDLC frame or
4911                  * for every buffer in raw mode
4912                  */
4913                 if ((!size && info->params.mode == MGSL_MODE_HDLC) ||
4914                     info->params.mode == MGSL_MODE_RAW)
4915                         set_desc_eof(*d, 1);
4916                 else
4917                         set_desc_eof(*d, 0);
4918
4919                 /* set descriptor count for all but first buffer */
4920                 if (i != info->tbuf_start)
4921                         set_desc_count(*d, count);
4922                 d->buf_count = count;
4923
4924                 if (++i == info->tbuf_count)
4925                         i = 0;
4926         }
4927
4928         info->tbuf_current = i;
4929
4930         /* set first buffer count to make new data visible to DMA controller */
4931         d = &info->tbufs[info->tbuf_start];
4932         set_desc_count(*d, d->buf_count);
4933
4934         /* start transmitter if needed and update transmit timeout */
4935         if (!info->tx_active)
4936                 tx_start(info);
4937         update_tx_timer(info);
4938
4939         return true;
4940 }
4941
4942 static int register_test(struct slgt_info *info)
4943 {
4944         static unsigned short patterns[] =
4945                 {0x0000, 0xffff, 0xaaaa, 0x5555, 0x6969, 0x9696};
4946         static unsigned int count = ARRAY_SIZE(patterns);
4947         unsigned int i;
4948         int rc = 0;
4949
4950         for (i=0 ; i < count ; i++) {
4951                 wr_reg16(info, TIR, patterns[i]);
4952                 wr_reg16(info, BDR, patterns[(i+1)%count]);
4953                 if ((rd_reg16(info, TIR) != patterns[i]) ||
4954                     (rd_reg16(info, BDR) != patterns[(i+1)%count])) {
4955                         rc = -ENODEV;
4956                         break;
4957                 }
4958         }
4959         info->gpio_present = (rd_reg32(info, JCR) & BIT5) ? 1 : 0;
4960         info->init_error = rc ? 0 : DiagStatus_AddressFailure;
4961         return rc;
4962 }
4963
4964 static int irq_test(struct slgt_info *info)
4965 {
4966         unsigned long timeout;
4967         unsigned long flags;
4968         struct tty_struct *oldtty = info->port.tty;
4969         u32 speed = info->params.data_rate;
4970
4971         info->params.data_rate = 921600;
4972         info->port.tty = NULL;
4973
4974         spin_lock_irqsave(&info->lock, flags);
4975         async_mode(info);
4976         slgt_irq_on(info, IRQ_TXIDLE);
4977
4978         /* enable transmitter */
4979         wr_reg16(info, TCR,
4980                 (unsigned short)(rd_reg16(info, TCR) | BIT1));
4981
4982         /* write one byte and wait for tx idle */
4983         wr_reg16(info, TDR, 0);
4984
4985         /* assume failure */
4986         info->init_error = DiagStatus_IrqFailure;
4987         info->irq_occurred = false;
4988
4989         spin_unlock_irqrestore(&info->lock, flags);
4990
4991         timeout=100;
4992         while(timeout-- && !info->irq_occurred)
4993                 msleep_interruptible(10);
4994
4995         spin_lock_irqsave(&info->lock,flags);
4996         reset_port(info);
4997         spin_unlock_irqrestore(&info->lock,flags);
4998
4999         info->params.data_rate = speed;
5000         info->port.tty = oldtty;
5001
5002         info->init_error = info->irq_occurred ? 0 : DiagStatus_IrqFailure;
5003         return info->irq_occurred ? 0 : -ENODEV;
5004 }
5005
5006 static int loopback_test_rx(struct slgt_info *info)
5007 {
5008         unsigned char *src, *dest;
5009         int count;
5010
5011         if (desc_complete(info->rbufs[0])) {
5012                 count = desc_count(info->rbufs[0]);
5013                 src   = info->rbufs[0].buf;
5014                 dest  = info->tmp_rbuf;
5015
5016                 for( ; count ; count-=2, src+=2) {
5017                         /* src=data byte (src+1)=status byte */
5018                         if (!(*(src+1) & (BIT9 + BIT8))) {
5019                                 *dest = *src;
5020                                 dest++;
5021                                 info->tmp_rbuf_count++;
5022                         }
5023                 }
5024                 DBGDATA(info, info->tmp_rbuf, info->tmp_rbuf_count, "rx");
5025                 return 1;
5026         }
5027         return 0;
5028 }
5029
5030 static int loopback_test(struct slgt_info *info)
5031 {
5032 #define TESTFRAMESIZE 20
5033
5034         unsigned long timeout;
5035         u16 count = TESTFRAMESIZE;
5036         unsigned char buf[TESTFRAMESIZE];
5037         int rc = -ENODEV;
5038         unsigned long flags;
5039
5040         struct tty_struct *oldtty = info->port.tty;
5041         MGSL_PARAMS params;
5042
5043         memcpy(&params, &info->params, sizeof(params));
5044
5045         info->params.mode = MGSL_MODE_ASYNC;
5046         info->params.data_rate = 921600;
5047         info->params.loopback = 1;
5048         info->port.tty = NULL;
5049
5050         /* build and send transmit frame */
5051         for (count = 0; count < TESTFRAMESIZE; ++count)
5052                 buf[count] = (unsigned char)count;
5053
5054         info->tmp_rbuf_count = 0;
5055         memset(info->tmp_rbuf, 0, TESTFRAMESIZE);
5056
5057         /* program hardware for HDLC and enabled receiver */
5058         spin_lock_irqsave(&info->lock,flags);
5059         async_mode(info);
5060         rx_start(info);
5061         tx_load(info, buf, count);
5062         spin_unlock_irqrestore(&info->lock, flags);
5063
5064         /* wait for receive complete */
5065         for (timeout = 100; timeout; --timeout) {
5066                 msleep_interruptible(10);
5067                 if (loopback_test_rx(info)) {
5068                         rc = 0;
5069                         break;
5070                 }
5071         }
5072
5073         /* verify received frame length and contents */
5074         if (!rc && (info->tmp_rbuf_count != count ||
5075                   memcmp(buf, info->tmp_rbuf, count))) {
5076                 rc = -ENODEV;
5077         }
5078
5079         spin_lock_irqsave(&info->lock,flags);
5080         reset_adapter(info);
5081         spin_unlock_irqrestore(&info->lock,flags);
5082
5083         memcpy(&info->params, &params, sizeof(info->params));
5084         info->port.tty = oldtty;
5085
5086         info->init_error = rc ? DiagStatus_DmaFailure : 0;
5087         return rc;
5088 }
5089
5090 static int adapter_test(struct slgt_info *info)
5091 {
5092         DBGINFO(("testing %s\n", info->device_name));
5093         if (register_test(info) < 0) {
5094                 printk("register test failure %s addr=%08X\n",
5095                         info->device_name, info->phys_reg_addr);
5096         } else if (irq_test(info) < 0) {
5097                 printk("IRQ test failure %s IRQ=%d\n",
5098                         info->device_name, info->irq_level);
5099         } else if (loopback_test(info) < 0) {
5100                 printk("loopback test failure %s\n", info->device_name);
5101         }
5102         return info->init_error;
5103 }
5104
5105 /*
5106  * transmit timeout handler
5107  */
5108 static void tx_timeout(unsigned long context)
5109 {
5110         struct slgt_info *info = (struct slgt_info*)context;
5111         unsigned long flags;
5112
5113         DBGINFO(("%s tx_timeout\n", info->device_name));
5114         if(info->tx_active && info->params.mode == MGSL_MODE_HDLC) {
5115                 info->icount.txtimeout++;
5116         }
5117         spin_lock_irqsave(&info->lock,flags);
5118         tx_stop(info);
5119         spin_unlock_irqrestore(&info->lock,flags);
5120
5121 #if SYNCLINK_GENERIC_HDLC
5122         if (info->netcount)
5123                 hdlcdev_tx_done(info);
5124         else
5125 #endif
5126                 bh_transmit(info);
5127 }
5128
5129 /*
5130  * receive buffer polling timer
5131  */
5132 static void rx_timeout(unsigned long context)
5133 {
5134         struct slgt_info *info = (struct slgt_info*)context;
5135         unsigned long flags;
5136
5137         DBGINFO(("%s rx_timeout\n", info->device_name));
5138         spin_lock_irqsave(&info->lock, flags);
5139         info->pending_bh |= BH_RECEIVE;
5140         spin_unlock_irqrestore(&info->lock, flags);
5141         bh_handler(&info->task);
5142 }
5143