2 * FB driver for the SSD1306 OLED Controller
4 * Copyright (C) 2013 Noralf Tronnes
6 * This program is free software; you can redistribute it and/or modify
7 * it under the terms of the GNU General Public License as published by
8 * the Free Software Foundation; either version 2 of the License, or
9 * (at your option) any later version.
11 * This program is distributed in the hope that it will be useful,
12 * but WITHOUT ANY WARRANTY; without even the implied warranty of
13 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
14 * GNU General Public License for more details.
17 #include <linux/module.h>
18 #include <linux/kernel.h>
19 #include <linux/init.h>
20 #include <linux/gpio.h>
21 #include <linux/delay.h>
25 #define DRVNAME "fb_ssd1306"
32 This doesn't work because D/C has to be LOW for both values:
33 write_reg(par, val1, val2);
40 /* Init sequence taken from the Adafruit SSD1306 Arduino library */
41 static int init_display(struct fbtft_par *par)
43 par->fbtftops.reset(par);
45 if (par->gamma.curves[0] == 0) {
46 mutex_lock(&par->gamma.lock);
47 if (par->info->var.yres == 64)
48 par->gamma.curves[0] = 0xCF;
50 par->gamma.curves[0] = 0x8F;
51 mutex_unlock(&par->gamma.lock);
57 /* Set Display Clock Divide Ratio/ Oscillator Frequency */
61 /* Set Multiplex Ratio */
63 if (par->info->var.yres == 64)
68 /* Set Display Offset */
72 /* Set Display Start Line */
73 write_reg(par, 0x40 | 0x0);
75 /* Charge Pump Setting */
77 /* A[2] = 1b, Enable charge pump during display on */
80 /* Set Memory Addressing Mode */
82 /* Vertical addressing mode */
85 /*Set Segment Re-map */
86 /* column address 127 is mapped to SEG0 */
87 write_reg(par, 0xA0 | 0x1);
89 /* Set COM Output Scan Direction */
90 /* remapped mode. Scan from COM[N-1] to COM0 */
93 /* Set COM Pins Hardware Configuration */
95 if (par->info->var.yres == 64)
96 /* A[4]=1b, Alternative COM pin configuration */
99 /* A[4]=0b, Sequential COM pin configuration */
100 write_reg(par, 0x02);
102 /* Set Pre-charge Period */
103 write_reg(par, 0xD9);
104 write_reg(par, 0xF1);
106 /* Set VCOMH Deselect Level */
107 write_reg(par, 0xDB);
108 /* according to the datasheet, this value is out of bounds */
109 write_reg(par, 0x40);
111 /* Entire Display ON */
112 /* Resume to RAM content display. Output follows RAM content */
113 write_reg(par, 0xA4);
115 /* Set Normal Display
116 0 in RAM: OFF in display panel
117 1 in RAM: ON in display panel */
118 write_reg(par, 0xA6);
121 write_reg(par, 0xAF);
126 static void set_addr_win(struct fbtft_par *par, int xs, int ys, int xe, int ye)
128 /* Set Lower Column Start Address for Page Addressing Mode */
129 write_reg(par, 0x00 | 0x0);
130 /* Set Higher Column Start Address for Page Addressing Mode */
131 write_reg(par, 0x10 | 0x0);
132 /* Set Display Start Line */
133 write_reg(par, 0x40 | 0x0);
136 static int blank(struct fbtft_par *par, bool on)
138 fbtft_par_dbg(DEBUG_BLANK, par, "%s(blank=%s)\n",
139 __func__, on ? "true" : "false");
142 write_reg(par, 0xAE);
144 write_reg(par, 0xAF);
148 /* Gamma is used to control Contrast */
149 static int set_gamma(struct fbtft_par *par, unsigned long *curves)
154 /* Set Contrast Control for BANK0 */
155 write_reg(par, 0x81);
156 write_reg(par, curves[0]);
161 static int write_vmem(struct fbtft_par *par, size_t offset, size_t len)
163 u16 *vmem16 = (u16 *)par->info->screen_buffer;
164 u8 *buf = par->txbuf.buf;
168 for (x = 0; x < par->info->var.xres; x++) {
169 for (y = 0; y < par->info->var.yres/8; y++) {
171 for (i = 0; i < 8; i++)
172 *buf |= (vmem16[(y * 8 + i) *
173 par->info->var.xres + x] ?
180 gpio_set_value(par->gpio.dc, 1);
181 ret = par->fbtftops.write(par, par->txbuf.buf,
182 par->info->var.xres * par->info->var.yres /
185 dev_err(par->info->device, "write failed and returned: %d\n",
191 static struct fbtft_display display = {
199 .write_vmem = write_vmem,
200 .init_display = init_display,
201 .set_addr_win = set_addr_win,
203 .set_gamma = set_gamma,
207 FBTFT_REGISTER_DRIVER(DRVNAME, "solomon,ssd1306", &display);
209 MODULE_ALIAS("spi:" DRVNAME);
210 MODULE_ALIAS("platform:" DRVNAME);
211 MODULE_ALIAS("spi:ssd1306");
212 MODULE_ALIAS("platform:ssd1306");
214 MODULE_DESCRIPTION("SSD1306 OLED Driver");
215 MODULE_AUTHOR("Noralf Tronnes");
216 MODULE_LICENSE("GPL");