1 # SPDX-License-Identifier: GPL-2.0-only
3 # SPI driver configuration
9 The "Serial Peripheral Interface" is a low level synchronous
10 protocol. Chips that support SPI can have data transfer rates
11 up to several tens of Mbit/sec. Chips are addressed with a
12 controller and a chipselect. Most SPI slaves don't support
13 dynamic device discovery; some are even write-only or read-only.
15 SPI is widely used by microcontrollers to talk with sensors,
16 eeprom and flash memory, codecs and various other controller
17 chips, analog to digital (and d-to-a) converters, and more.
18 MMC and SD cards can be accessed using SPI protocol; and for
19 DataFlash cards used in MMC sockets, SPI must always be used.
21 SPI is one of a family of similar protocols using a four wire
22 interface (select, clock, data in, data out) including Microwire
23 (half duplex), SSP, SSI, and PSP. This driver framework should
24 work with most such devices and controllers.
29 bool "Debug support for SPI drivers"
30 depends on DEBUG_KERNEL
32 Say "yes" to enable debug messaging (like dev_dbg and pr_debug),
33 sysfs, and debugfs support in SPI controller and protocol drivers.
36 # MASTER side ... talking to discrete SPI slave chips including microcontrollers
40 # bool "SPI Master Support"
44 If your system has an master-capable SPI controller (which
45 provides the clock and chipselect), you can enable that
46 controller and the protocol drivers for the SPI slave chips
52 bool "SPI memory extension"
54 Enable this option if you want to enable the SPI memory extension.
55 This extension is meant to simplify interaction with SPI memories
56 by providing a high-level interface to send memory-like commands.
58 comment "SPI Master Controller Drivers"
61 tristate "Altera SPI Controller platform driver"
62 select SPI_ALTERA_CORE
65 This is the driver for the Altera SPI Controller.
67 config SPI_ALTERA_CORE
68 tristate "Altera SPI Controller core code" if COMPILE_TEST
71 "The core code for the Altera SPI Controller"
74 tristate "DFL bus driver for Altera SPI Controller"
76 select SPI_ALTERA_CORE
78 This is a Device Feature List (DFL) bus driver for the
79 Altera SPI master controller. The SPI master is connected
80 to a SPI slave to Avalon bridge in a Intel MAX BMC.
83 tristate "Qualcomm Atheros AR934X/QCA95XX SPI controller driver"
84 depends on ATH79 || COMPILE_TEST
86 This enables support for the SPI controller present on the
87 Qualcomm Atheros AR934X/QCA95XX SoCs.
90 tristate "Atheros AR71XX/AR724X/AR913X SPI controller driver"
91 depends on ATH79 || COMPILE_TEST
94 This enables support for the SPI controller present on the
95 Atheros AR71XX/AR724X/AR913X SoCs.
97 config SPI_ARMADA_3700
98 tristate "Marvell Armada 3700 SPI Controller"
99 depends on (ARCH_MVEBU && OF) || COMPILE_TEST
101 This enables support for the SPI controller present on the
102 Marvell Armada 3700 SoCs.
104 config SPI_ASPEED_SMC
105 tristate "Aspeed flash controllers in SPI mode"
106 depends on ARCH_ASPEED || COMPILE_TEST
109 This enables support for the Firmware Memory controller (FMC)
110 in the Aspeed AST2600, AST2500 and AST2400 SoCs when attached
111 to SPI NOR chips, and support for the SPI flash memory
112 controller (SPI) for the host firmware. The implementation
113 only supports SPI NOR.
116 tristate "Atmel SPI Controller"
117 depends on ARCH_AT91 || COMPILE_TEST
120 This selects a driver for the Atmel SPI Controller, present on
123 config SPI_AT91_USART
124 tristate "Atmel USART Controller SPI driver"
125 depends on (ARCH_AT91 || COMPILE_TEST)
126 depends on MFD_AT91_USART
128 This selects a driver for the AT91 USART Controller as SPI Master,
129 present on AT91 and SAMA5 SoC series.
131 config SPI_ATMEL_QUADSPI
132 tristate "Atmel Quad SPI Controller"
133 depends on ARCH_AT91 || COMPILE_TEST
134 depends on OF && HAS_IOMEM
136 This enables support for the Quad SPI controller in master mode.
137 This driver does not support generic SPI. The implementation only
138 supports spi-mem interface.
141 tristate "Au1550/Au1200/Au1300 SPI Controller"
142 depends on MIPS_ALCHEMY
145 If you say yes to this option, support will be included for the
146 PSC SPI controller found on Au1550, Au1200 and Au1300 series.
148 config SPI_AXI_SPI_ENGINE
149 tristate "Analog Devices AXI SPI Engine controller"
152 This enables support for the Analog Devices AXI SPI Engine SPI controller.
153 It is part of the SPI Engine framework that is used in some Analog Devices
154 reference designs for FPGAs.
157 tristate "BCM2835 SPI controller"
159 depends on ARCH_BCM2835 || ARCH_BRCMSTB || COMPILE_TEST
161 This selects a driver for the Broadcom BCM2835 SPI master.
163 The BCM2835 contains two types of SPI master controller; the
164 "universal SPI master", and the regular SPI controller. This driver
165 is for the regular SPI controller. Slave mode operation is not also
168 config SPI_BCM2835AUX
169 tristate "BCM2835 SPI auxiliary controller"
170 depends on ((ARCH_BCM2835 || ARCH_BRCMSTB) && GPIOLIB) || COMPILE_TEST
172 This selects a driver for the Broadcom BCM2835 SPI aux master.
174 The BCM2835 contains two types of SPI master controller; the
175 "universal SPI master", and the regular SPI controller.
176 This driver is for the universal/auxiliary SPI controller.
179 tristate "Broadcom BCM63xx SPI controller"
180 depends on BCM63XX || BMIPS_GENERIC || COMPILE_TEST
182 Enable support for the SPI controller on the Broadcom BCM63xx SoCs.
184 config SPI_BCM63XX_HSSPI
185 tristate "Broadcom BCM63XX HS SPI controller driver"
186 depends on BCM63XX || BMIPS_GENERIC || ARCH_BCMBCA || COMPILE_TEST
188 This enables support for the High Speed SPI controller present on
189 newer Broadcom BCM63XX SoCs.
192 tristate "Broadcom BSPI and MSPI controller support"
193 depends on ARCH_BRCMSTB || ARCH_BCM || ARCH_BCM_IPROC || \
194 BMIPS_GENERIC || COMPILE_TEST
195 default ARCH_BCM_IPROC
197 Enables support for the Broadcom SPI flash and MSPI controller.
198 Select this option for any one of BRCMSTB, iProc NSP and NS2 SoCs
199 based platforms. This driver works for both SPI master for SPI NOR
200 flash device as well as MSPI device.
203 tristate "Utilities for Bitbanging SPI masters"
205 With a few GPIO pins, your system can bitbang the SPI protocol.
206 Select this to get SPI support through I/O pins (GPIO, parallel
207 port, etc). Or, some systems' SPI master controller drivers use
208 this code to manage the per-word or per-transfer accesses to the
209 hardware shift registers.
211 This is library code, and is automatically selected by drivers that
212 need it. You only need to select this explicitly to support driver
213 modules that aren't part of this kernel tree.
216 tristate "Parallel port adapter for AVR Butterfly (DEVELOPMENT)"
220 This uses a custom parallel port cable to connect to an AVR
221 Butterfly <http://www.atmel.com/products/avr/butterfly>, an
222 inexpensive battery powered microcontroller evaluation board.
223 This same cable can be used to flash new firmware.
226 tristate "Cadence SPI controller"
228 This selects the Cadence SPI controller master driver
229 used by Xilinx Zynq and ZynqMP.
231 config SPI_CADENCE_QUADSPI
232 tristate "Cadence Quad SPI controller"
233 depends on OF && (ARM || ARM64 || X86 || COMPILE_TEST)
235 Enable support for the Cadence Quad SPI Flash controller.
237 Cadence QSPI is a specialized controller for connecting an SPI
238 Flash over 1/2/4-bit wide bus. Enable this option if you have a
239 device with a Cadence QSPI controller and want to access the
240 Flash as an MTD device.
242 config SPI_CADENCE_XSPI
243 tristate "Cadence XSPI controller"
244 depends on (OF || COMPILE_TEST) && HAS_IOMEM
247 Enable support for the Cadence XSPI Flash controller.
249 Cadence XSPI is a specialized controller for connecting an SPI
250 Flash over upto 8bit wide bus. Enable this option if you have a
251 device with a Cadence XSPI controller and want to access the
252 Flash as an MTD device.
255 tristate "CLPS711X host SPI controller"
256 depends on ARCH_CLPS711X || COMPILE_TEST
258 This enables dedicated general purpose SPI/Microwire1-compatible
259 master mode interface (SSI1) for CLPS711X-based CPUs.
261 config SPI_COLDFIRE_QSPI
262 tristate "Freescale Coldfire QSPI controller"
263 depends on (M520x || M523x || M5249 || M525x || M527x || M528x || M532x)
265 This enables support for the Coldfire QSPI controller in master
269 tristate "Texas Instruments DaVinci/DA8x/OMAP-L/AM1x SoC SPI controller"
270 depends on ARCH_DAVINCI || ARCH_KEYSTONE
273 SPI master controller for DaVinci/DA8x/OMAP-L/AM1x SPI modules.
275 config SPI_DESIGNWARE
276 tristate "DesignWare SPI controller core support"
279 general driver for SPI controller core from DesignWare
284 bool "DMA support for DW SPI controller"
287 tristate "PCI interface driver for DW SPI core"
291 tristate "Memory-mapped io interface driver for DW SPI core"
295 tristate "Baikal-T1 SPI driver for DW SPI core"
296 depends on MIPS_BAIKAL_T1 || COMPILE_TEST
299 Baikal-T1 SoC is equipped with three DW APB SSI-based MMIO SPI
300 controllers. Two of them are pretty much normal: with IRQ, DMA,
301 FIFOs of 64 words depth, 4x CSs, but the third one as being a
302 part of the Baikal-T1 System Boot Controller has got a very
303 limited resources: no IRQ, no DMA, only a single native
304 chip-select and Tx/Rx FIFO with just 8 words depth available.
305 The later one is normally connected to an external SPI-nor flash
306 of 128Mb (in general can be of bigger size).
308 config SPI_DW_BT1_DIRMAP
309 bool "Directly mapped Baikal-T1 Boot SPI flash support"
310 depends on SPI_DW_BT1
312 Directly mapped SPI flash memory is an interface specific to the
313 Baikal-T1 System Boot Controller. It is a 16MB MMIO region, which
314 can be used to access a peripheral memory device just by
315 reading/writing data from/to it. Note that the system APB bus
316 will stall during each IO from/to the dirmap region until the
317 operation is finished. So try not to use it concurrently with
318 time-critical tasks (like the SPI memory operations implemented
324 tristate "Diolan DLN-2 USB SPI adapter"
327 If you say yes to this option, support will be included for Diolan
328 DLN2, a USB to SPI interface.
330 This driver can also be built as a module. If so, the module
331 will be called spi-dln2.
334 tristate "Cirrus Logic EP93xx SPI controller"
335 depends on ARCH_EP93XX || COMPILE_TEST
337 This enables using the Cirrus EP93xx SPI controller in master
341 bool "Falcon SPI controller support"
342 depends on SOC_FALCON
344 The external bus unit (EBU) found on the FALC-ON SoC has SPI
345 emulation that is designed for serial flash access. This driver
346 has only been tested with m25p80 type chips. The hardware has no
347 support for other types of SPI peripherals.
350 tristate "FSI SPI driver"
353 This enables support for the driver for FSI bus attached SPI
357 tristate "Freescale i.MX LPSPI controller"
358 depends on ARCH_MXC || COMPILE_TEST
360 This enables Freescale i.MX LPSPI controllers in master mode.
362 config SPI_FSL_QUADSPI
363 tristate "Freescale QSPI controller"
364 depends on ARCH_MXC || SOC_LS1021A || ARCH_LAYERSCAPE || COMPILE_TEST
367 This enables support for the Quad SPI controller in master mode.
368 Up to four flash chips can be connected on two buses with two
370 This controller does not support generic SPI messages. It only
371 supports the high-level SPI memory interface.
374 tristate "GXP SPI driver"
375 depends on ARCH_HPE || COMPILE_TEST
377 This enables support for the driver for GXP bus attached SPI
380 config SPI_HISI_KUNPENG
381 tristate "HiSilicon SPI Controller for Kunpeng SoCs"
382 depends on (ARM64 && ACPI) || COMPILE_TEST
384 This enables support for HiSilicon SPI controller found on
387 This driver can also be built as a module. If so, the module
388 will be called hisi-kunpeng-spi.
390 config SPI_HISI_SFC_V3XX
391 tristate "HiSilicon SPI NOR Flash Controller for Hi16XX chipsets"
392 depends on (ARM64 && ACPI) || COMPILE_TEST
395 This enables support for HiSilicon v3xx SPI NOR flash controller
396 found in hi16xx chipsets.
398 config SPI_NXP_FLEXSPI
399 tristate "NXP Flex SPI controller"
400 depends on ARCH_LAYERSCAPE || HAS_IOMEM
402 This enables support for the Flex SPI controller in master mode.
403 Up to four slave devices can be connected on two buses with two
405 This controller does not support generic SPI messages and only
406 supports the high-level SPI memory interface.
409 tristate "GPIO-based bitbanging SPI Master"
410 depends on GPIOLIB || COMPILE_TEST
413 This simple GPIO bitbanging SPI master uses the arch-neutral GPIO
414 interface to manage MOSI, MISO, SCK, and chipselect signals. SPI
415 slaves connected to a bus using this driver are configured as usual,
416 except that the spi_board_info.controller_data holds the GPIO number
417 for the chipselect used by this controller driver.
419 Note that this driver often won't achieve even 1 Mbit/sec speeds,
420 making it unusually slow for SPI. If your platform can inline
421 GPIO operations, you should be able to leverage that for better
422 speed with a custom version of this driver; see the source code.
425 tristate "IMG SPFI controller"
426 depends on MIPS || COMPILE_TEST
428 This enables support for the SPFI master controller found on
432 tristate "Freescale i.MX SPI controllers"
433 depends on ARCH_MXC || COMPILE_TEST
435 This enables support for the Freescale i.MX SPI controllers.
438 tristate "Ingenic SoCs SPI controller"
439 depends on MACH_INGENIC || COMPILE_TEST
441 This enables support for the Ingenic SoCs SPI controller.
443 To compile this driver as a module, choose M here: the module
444 will be called spi-ingenic.
450 tristate "Intel PCH/PCU SPI flash PCI driver (DANGEROUS)"
452 depends on X86 || COMPILE_TEST
456 This enables PCI support for the Intel PCH/PCU SPI controller in
457 master mode. This controller is present in modern Intel hardware
458 and is used to hold BIOS and other persistent settings. Using
459 this driver it is possible to upgrade BIOS directly from Linux.
461 Say N here unless you know what you are doing. Overwriting the
462 SPI flash may render the system unbootable.
464 To compile this driver as a module, choose M here: the module
465 will be called spi-intel-pci.
467 config SPI_INTEL_PLATFORM
468 tristate "Intel PCH/PCU SPI flash platform driver (DANGEROUS)"
469 depends on X86 || COMPILE_TEST
473 This enables platform support for the Intel PCH/PCU SPI
474 controller in master mode. This controller is present in modern
475 Intel hardware and is used to hold BIOS and other persistent
476 settings. Using this driver it is possible to upgrade BIOS
479 Say N here unless you know what you are doing. Overwriting the
480 SPI flash may render the system unbootable.
482 To compile this driver as a module, choose M here: the module
483 will be called spi-intel-platform.
486 tristate "J-Core SPI Master"
487 depends on OF && (SUPERH || COMPILE_TEST)
489 This enables support for the SPI master controller in the J-Core
490 synthesizable, open source SoC.
493 tristate "Parallel port adapter for LM70 eval board (DEVELOPMENT)"
497 This driver supports the NS LM70 LLP Evaluation Board,
498 which interfaces to an LM70 temperature sensor using
501 config SPI_LP8841_RTC
502 tristate "ICP DAS LP-8841 SPI Controller for RTC"
503 depends on MACH_PXA27X_DT || COMPILE_TEST
505 This driver provides an SPI master device to drive Maxim
506 DS-1302 real time clock.
508 Say N here unless you plan to run the kernel on an ICP DAS
509 LP-8x4x industrial computer.
512 tristate "Freescale MPC52xx SPI (non-PSC) controller support"
513 depends on PPC_MPC52xx
515 This drivers supports the MPC52xx SPI controller in master SPI
518 config SPI_MPC52xx_PSC
519 tristate "Freescale MPC52xx PSC SPI controller"
520 depends on PPC_MPC52xx
522 This enables using the Freescale MPC52xx Programmable Serial
523 Controller in master SPI mode.
525 config SPI_MPC512x_PSC
526 tristate "Freescale MPC512x PSC SPI controller"
527 depends on PPC_MPC512x
529 This enables using the Freescale MPC5121 Programmable Serial
530 Controller in SPI master mode.
541 tristate "Freescale SPI controller and Aeroflex Gaisler GRLIB SPI controller"
544 select SPI_FSL_CPM if FSL_SOC
546 This enables using the Freescale SPI controllers in master mode.
547 MPC83xx platform uses the controller in cpu mode or CPM/QE mode.
548 MPC8569 uses the controller in QE mode, MPC8610 in cpu mode.
549 This also enables using the Aeroflex Gaisler GRLIB SPI controller in
553 tristate "Freescale DSPI controller"
555 depends on SOC_VF610 || SOC_LS1021A || ARCH_LAYERSCAPE || M5441x || COMPILE_TEST
557 This enables support for the Freescale DSPI controller in master
558 mode. VF610, LS1021A and ColdFire platforms uses the controller.
561 tristate "Freescale eSPI controller"
564 This enables using the Freescale eSPI controllers in master mode.
565 From MPC8536, 85xx platform uses the controller, and all P10xx,
566 P20xx, P30xx,P40xx, P50xx uses this controller.
568 config SPI_MESON_SPICC
569 tristate "Amlogic Meson SPICC controller"
570 depends on COMMON_CLK
571 depends on ARCH_MESON || COMPILE_TEST
573 This enables master mode support for the SPICC (SPI communication
574 controller) available in Amlogic Meson SoCs.
576 config SPI_MESON_SPIFC
577 tristate "Amlogic Meson SPIFC controller"
578 depends on ARCH_MESON || COMPILE_TEST
581 This enables master mode support for the SPIFC (SPI flash
582 controller) available in Amlogic Meson SoCs.
584 config SPI_MICROCHIP_CORE
585 tristate "Microchip FPGA SPI controllers"
586 depends on SPI_MASTER
588 This enables the SPI driver for Microchip FPGA SPI controllers.
589 Say Y or M here if you want to use the "hard" controllers on
591 If built as a module, it will be called spi-microchip-core.
593 config SPI_MICROCHIP_CORE_QSPI
594 tristate "Microchip FPGA QSPI controllers"
595 depends on SPI_MASTER
597 This enables the QSPI driver for Microchip FPGA QSPI controllers.
598 Say Y or M here if you want to use the QSPI controllers on
600 If built as a module, it will be called spi-microchip-core-qspi.
603 tristate "MediaTek SPI controller"
604 depends on ARCH_MEDIATEK || COMPILE_TEST
606 This selects the MediaTek(R) SPI bus driver.
607 If you want to use MediaTek(R) SPI interface,
608 say Y or M here.If you are not sure, say N.
609 SPI drivers for Mediatek MT65XX and MT81XX series ARM SoCs.
612 tristate "MediaTek MT7621 SPI Controller"
613 depends on RALINK || COMPILE_TEST
615 This selects a driver for the MediaTek MT7621 SPI Controller.
618 tristate "MediaTek SPI NOR controller"
619 depends on ARCH_MEDIATEK || COMPILE_TEST
621 This enables support for SPI NOR controller found on MediaTek
622 ARM SoCs. This is a controller specifically for SPI NOR flash.
623 It can perform generic SPI transfers up to 6 bytes via generic
624 SPI interface as well as several SPI NOR specific instructions
625 via SPI MEM interface.
628 tristate "MediaTek SPI NAND Flash Interface"
629 depends on ARCH_MEDIATEK || COMPILE_TEST
630 depends on MTD_NAND_ECC_MEDIATEK
632 This enables support for SPI-NAND mode on the MediaTek NAND
633 Flash Interface found on MediaTek ARM SoCs. This controller
634 is implemented as a SPI-MEM controller with pipelined ECC
638 tristate "Nuvoton NPCM FLASH Interface Unit"
639 depends on ARCH_NPCM || COMPILE_TEST
640 depends on OF && HAS_IOMEM
642 This enables support for the Flash Interface Unit SPI controller
644 This driver does not support generic SPI. The implementation only
645 supports spi-mem interface.
648 tristate "Nuvoton NPCM PSPI Controller"
649 depends on ARCH_NPCM || COMPILE_TEST
651 This driver provides support for Nuvoton NPCM BMC
652 Peripheral SPI controller in master mode.
654 config SPI_LANTIQ_SSC
655 tristate "Lantiq SSC SPI controller"
656 depends on LANTIQ || X86 || COMPILE_TEST
658 This driver supports the Lantiq SSC SPI controller in master
659 mode. This controller is found on Intel (former Lantiq) SoCs like
660 the Danube, Falcon, xRX200, xRX300, Lightning Mountain.
663 tristate "OpenCores tiny SPI"
664 depends on GPIOLIB || COMPILE_TEST
667 This is the driver for OpenCores tiny SPI master controller.
670 tristate "Cavium OCTEON SPI controller"
671 depends on CAVIUM_OCTEON_SOC
673 SPI host driver for the hardware found on some Cavium OCTEON
676 config SPI_OMAP_UWIRE
677 tristate "OMAP1 MicroWire"
678 depends on ARCH_OMAP1 || (ARM && COMPILE_TEST)
681 This hooks up to the MicroWire controller on OMAP1 chips.
684 tristate "McSPI driver for OMAP"
685 depends on ARCH_OMAP2PLUS || ARCH_K3 || COMPILE_TEST
688 SPI master controller for OMAP24XX and later Multichannel SPI
692 tristate "DRA7xxx QSPI controller support"
693 depends on ARCH_OMAP2PLUS || COMPILE_TEST
695 QSPI master controller for DRA7xxx used for flash devices.
696 This device supports single, dual and quad read support, while
697 it only supports single write mode.
700 tristate "OMAP SPI 100K"
701 depends on ARCH_OMAP850 || ARCH_OMAP730 || COMPILE_TEST
703 OMAP SPI 100K master controller for omap7xx boards.
706 tristate "Orion SPI master"
707 depends on PLAT_ORION || ARCH_MVEBU || COMPILE_TEST
709 This enables using the SPI master controller on the Orion
713 tristate "Microchip PIC32 series SPI"
714 depends on MACH_PIC32 || COMPILE_TEST
716 SPI driver for Microchip PIC32 SPI master controller.
719 tristate "Microchip PIC32 Quad SPI driver"
720 depends on MACH_PIC32 || COMPILE_TEST
722 SPI driver for PIC32 Quad SPI controller.
725 tristate "ARM AMBA PL022 SSP controller"
727 default y if ARCH_REALVIEW
728 default y if INTEGRATOR_IMPD1
729 default y if ARCH_VERSATILE
731 This selects the ARM(R) AMBA(R) PrimeCell PL022 SSP
732 controller. If you have an embedded system with an AMBA(R)
733 bus and a PL022 controller, say Y or M here.
736 tristate "PPC4xx SPI Controller"
737 depends on PPC32 && 4xx
740 This selects a driver for the PPC4xx SPI Controller.
743 tristate "PXA2xx SSP SPI master"
744 depends on ARCH_PXA || ARCH_MMP || PCI || ACPI || COMPILE_TEST
745 select PXA_SSP if ARCH_PXA || ARCH_MMP
747 This enables using a PXA2xx or Sodaville SSP port as a SPI master
748 controller. The driver can be configured to use any SSP port and
749 additional documentation can be found a Documentation/spi/pxa2xx.rst.
751 config SPI_PXA2XX_PCI
752 def_tristate SPI_PXA2XX && PCI && COMMON_CLK
755 tristate "Rockchip SPI controller driver"
757 This selects a driver for Rockchip SPI controller.
759 If you say yes to this option, support will be included for
760 RK3066, RK3188 and RK3288 families of SPI controller.
761 Rockchip SPI controller support DMA transport and PIO mode.
762 The main usecase of this controller is to use spi flash as boot
765 config SPI_ROCKCHIP_SFC
766 tristate "Rockchip Serial Flash Controller (SFC)"
767 depends on ARCH_ROCKCHIP || COMPILE_TEST
768 depends on HAS_IOMEM && HAS_DMA
770 This enables support for Rockchip serial flash controller. This
771 is a specialized controller used to access SPI flash on some
774 ROCKCHIP SFC supports DMA and PIO modes. When DMA is not available,
775 the driver automatically falls back to PIO mode.
778 tristate "Mikrotik RB4XX SPI master"
779 depends on SPI_MASTER && ATH79
781 SPI controller driver for the Mikrotik RB4xx series boards.
784 tristate "Renesas RPC-IF SPI driver"
785 depends on RENESAS_RPCIF
787 SPI driver for Renesas R-Car Gen3 or RZ/G2 RPC-IF.
790 tristate "Renesas RSPI/QSPI controller"
791 depends on SUPERH || ARCH_RENESAS || COMPILE_TEST
793 SPI driver for Renesas RSPI and QSPI blocks.
796 tristate "QTI QSPI controller"
799 QSPI(Quad SPI) driver for Qualcomm QSPI controller.
802 tristate "Qualcomm SPI controller with QUP interface"
803 depends on ARCH_QCOM || COMPILE_TEST
805 Qualcomm Universal Peripheral (QUP) core is an AHB slave that
806 provides a common data path (an output FIFO and an input FIFO)
807 for serial peripheral interface (SPI) mini-core. SPI in master
808 mode supports up to 50MHz, up to four chip selects, programmable
809 data path from 4 bits to 32 bits and numerous protocol variants.
811 This driver can also be built as a module. If so, the module
812 will be called spi_qup.
815 tristate "Qualcomm GENI based SPI controller"
816 depends on QCOM_GENI_SE
818 This driver supports GENI serial engine based SPI controller in
819 master mode on the Qualcomm Technologies Inc.'s SoCs. If you say
820 yes to this option, support will be included for the built-in SPI
821 interface on the Qualcomm Technologies Inc.'s SoCs.
823 This driver can also be built as a module. If so, the module
824 will be called spi-geni-qcom.
827 tristate "Samsung S3C24XX series SPI"
828 depends on ARCH_S3C24XX
831 SPI driver for Samsung S3C24XX series ARM SoCs
833 config SPI_S3C24XX_FIQ
834 bool "S3C24XX driver with FIQ pseudo-DMA"
835 depends on SPI_S3C24XX
838 Enable FIQ support for the S3C24XX SPI driver to provide pseudo
839 DMA by using the fast-interrupt request framework, This allows
840 the driver to get DMA-like performance when there are either
841 no free DMA channels, or when doing transfers that required both
842 TX and RX data paths.
845 tristate "Samsung S3C64XX/Exynos SoC series type SPI"
846 depends on (PLAT_SAMSUNG || ARCH_S5PV210 || ARCH_EXYNOS || COMPILE_TEST)
848 SPI driver for Samsung S3C64XX, S5Pv210 and Exynos SoCs.
849 Choose Y/M here only if you build for such Samsung SoC.
852 tristate "NXP SC18IS602/602B/603 I2C to SPI bridge"
855 SPI driver for NXP SC18IS602/602B/603 I2C to SPI bridge.
858 tristate "SuperH MSIOF SPI controller"
860 depends on ARCH_SHMOBILE || ARCH_RENESAS || COMPILE_TEST
862 SPI driver for SuperH and SH Mobile MSIOF blocks.
865 tristate "SuperH SPI controller"
866 depends on SUPERH || COMPILE_TEST
868 SPI driver for SuperH SPI blocks.
871 tristate "SuperH SCI SPI controller"
875 SPI driver for SuperH SCI blocks.
878 tristate "SuperH HSPI controller"
879 depends on ARCH_RENESAS || COMPILE_TEST
881 SPI driver for SuperH HSPI blocks.
884 tristate "SiFive SPI controller"
887 This exposes the SPI controller IP from SiFive.
889 config SPI_SLAVE_MT27XX
890 tristate "MediaTek SPI slave device"
891 depends on ARCH_MEDIATEK || COMPILE_TEST
894 This selects the MediaTek(R) SPI slave device driver.
895 If you want to use MediaTek(R) SPI slave interface,
896 say Y or M here.If you are not sure, say N.
897 SPI slave drivers for Mediatek MT27XX series ARM SoCs.
900 tristate "Spreadtrum SPI controller"
901 depends on ARCH_SPRD || COMPILE_TEST
903 SPI driver for Spreadtrum SoCs.
906 tristate "Spreadtrum ADI controller"
907 depends on ARCH_SPRD || COMPILE_TEST
908 depends on HWSPINLOCK || (COMPILE_TEST && !HWSPINLOCK)
910 ADI driver based on SPI for Spreadtrum SoCs.
913 tristate "STMicroelectronics STM32 SPI controller"
914 depends on ARCH_STM32 || COMPILE_TEST
916 SPI driver for STMicroelectronics STM32 SoCs.
918 STM32 SPI controller supports DMA and PIO modes. When DMA
919 is not available, the driver automatically falls back to
922 config SPI_STM32_QSPI
923 tristate "STMicroelectronics STM32 QUAD SPI controller"
924 depends on ARCH_STM32 || COMPILE_TEST
928 This enables support for the Quad SPI controller in master mode.
929 This driver does not support generic SPI. The implementation only
930 supports spi-mem interface.
933 tristate "STMicroelectronics SPI SSC-based driver"
934 depends on ARCH_STI || COMPILE_TEST
936 STMicroelectronics SoCs support for SPI. If you say yes to
937 this option, support will be included for the SSC driven SPI.
940 tristate "Allwinner A10 SoCs SPI controller"
941 depends on ARCH_SUNXI || COMPILE_TEST
943 SPI driver for Allwinner sun4i, sun5i and sun7i SoCs
946 tristate "Allwinner A31 SPI controller"
947 depends on ARCH_SUNXI || COMPILE_TEST
948 depends on RESET_CONTROLLER
950 This enables using the SPI controller on the Allwinner A31 SoCs.
952 config SPI_SUNPLUS_SP7021
953 tristate "Sunplus SP7021 SPI controller"
954 depends on SOC_SP7021 || COMPILE_TEST
956 This enables Sunplus SP7021 SPI controller driver on the SP7021 SoCs.
957 This driver can also be built as a module. If so, the module will be
958 called as spi-sunplus-sp7021.
960 If you have a Sunplus SP7021 platform say Y here.
964 tristate "Socionext's SynQuacer HighSpeed SPI controller"
965 depends on ARCH_SYNQUACER || COMPILE_TEST
967 SPI driver for Socionext's High speed SPI controller which provides
968 various operating modes for interfacing to serial peripheral devices
969 that use the de-facto standard SPI protocol.
971 It also supports the new dual-bit and quad-bit SPI protocol.
974 tristate "Macronix MX25F0A SPI controller"
975 depends on SPI_MASTER
976 imply MTD_NAND_ECC_MXIC
978 This selects the Macronix MX25F0A SPI controller driver.
981 tristate "Freescale MXS SPI controller"
985 SPI driver for Freescale MXS devices.
987 config SPI_TEGRA210_QUAD
988 tristate "NVIDIA Tegra QSPI Controller"
989 depends on ARCH_TEGRA || COMPILE_TEST
990 depends on RESET_CONTROLLER
992 QSPI driver for NVIDIA Tegra QSPI Controller interface. This
993 controller is different from the SPI controller and is available
994 on Tegra SoCs starting from Tegra210.
997 tristate "NVIDIA Tegra114 SPI Controller"
998 depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
999 depends on RESET_CONTROLLER
1001 SPI driver for NVIDIA Tegra114 SPI Controller interface. This controller
1002 is different than the older SoCs SPI controller and also register interface
1003 get changed with this controller.
1005 config SPI_TEGRA20_SFLASH
1006 tristate "Nvidia Tegra20 Serial flash Controller"
1007 depends on ARCH_TEGRA || COMPILE_TEST
1008 depends on RESET_CONTROLLER
1010 SPI driver for Nvidia Tegra20 Serial flash Controller interface.
1011 The main usecase of this controller is to use spi flash as boot
1014 config SPI_TEGRA20_SLINK
1015 tristate "Nvidia Tegra20/Tegra30 SLINK Controller"
1016 depends on (ARCH_TEGRA && TEGRA20_APB_DMA) || COMPILE_TEST
1017 depends on RESET_CONTROLLER
1019 SPI driver for Nvidia Tegra20/Tegra30 SLINK Controller interface.
1022 tristate "Cavium ThunderX SPI controller"
1023 depends on PCI && 64BIT && (ARM64 || COMPILE_TEST)
1025 SPI host driver for the hardware found on Cavium ThunderX
1028 config SPI_TOPCLIFF_PCH
1029 tristate "Intel EG20T PCH/LAPIS Semicon IOH(ML7213/ML7223/ML7831) SPI"
1030 depends on PCI && (X86_32 || MIPS || COMPILE_TEST)
1032 SPI driver for the Topcliff PCH (Platform Controller Hub) SPI bus
1033 used in some x86 embedded processors.
1035 This driver also supports the ML7213/ML7223/ML7831, a companion chip
1036 for the Atom E6xx series and compatible with the Intel EG20T PCH.
1039 tristate "Socionext UniPhier SPI Controller"
1040 depends on (ARCH_UNIPHIER || COMPILE_TEST) && OF
1041 depends on HAS_IOMEM
1043 This enables a driver for the Socionext UniPhier SoC SCSSI SPI controller.
1045 UniPhier SoCs have SCSSI and MCSSI SPI controllers.
1046 Every UniPhier SoC has SCSSI which supports single channel.
1047 Older UniPhier Pro4/Pro5 also has MCSSI which support multiple channels.
1048 This driver supports SCSSI only.
1050 If your SoC supports SCSSI, say Y here.
1053 tristate "Analog Devices AD-FMCOMMS1-EBZ SPI-I2C-bridge driver"
1056 Support for the SPI-I2C bridge found on the Analog Devices
1057 AD-FMCOMMS1-EBZ board.
1060 tristate "Xilinx SPI controller common module"
1061 depends on HAS_IOMEM
1064 This exposes the SPI controller IP from the Xilinx EDK.
1066 See the "OPB Serial Peripheral Interface (SPI) (v1.00e)"
1067 Product Specification document (DS464) for hardware details.
1069 Or for the DS570, see "XPS Serial Peripheral Interface (SPI) (v2.00b)"
1072 tristate "Cavium ThunderX2 SPI controller driver"
1073 depends on ARCH_THUNDER2 || COMPILE_TEST
1075 Enable support for the SPI controller on the Cavium ThunderX2.
1076 (Originally on Netlogic XLP SoCs.)
1078 If you have a Cavium ThunderX2 platform say Y here.
1081 config SPI_XTENSA_XTFPGA
1082 tristate "Xtensa SPI controller for xtfpga"
1083 depends on (XTENSA && XTENSA_PLATFORM_XTFPGA) || COMPILE_TEST
1086 SPI driver for xtfpga SPI master controller.
1088 This simple SPI master controller is built into xtfpga bitstreams
1089 and is used to control daughterboard audio codec. It always transfers
1090 16 bit words in SPI mode 0, automatically asserting CS on transfer
1091 start and deasserting on end.
1093 config SPI_ZYNQ_QSPI
1094 tristate "Xilinx Zynq QSPI controller"
1095 depends on ARCH_ZYNQ || COMPILE_TEST
1097 This enables support for the Zynq Quad SPI controller
1099 This controller only supports SPI memory interface.
1101 config SPI_ZYNQMP_GQSPI
1102 tristate "Xilinx ZynqMP GQSPI controller"
1103 depends on (SPI_MASTER && HAS_DMA) || COMPILE_TEST
1105 Enables Xilinx GQSPI controller driver for Zynq UltraScale+ MPSoC.
1108 tristate "AMD SPI controller"
1109 depends on SPI_MASTER || COMPILE_TEST
1111 Enables SPI controller driver for AMD SoC.
1114 # Add new SPI master controllers in alphabetical order above this line
1117 comment "SPI Multiplexer support"
1120 tristate "SPI multiplexer support"
1123 This adds support for SPI multiplexers. Each SPI mux will be
1124 accessible as a SPI controller, the devices behind the mux will appear
1125 to be chip selects on this controller. It is still necessary to
1126 select one or more specific mux-controller drivers.
1129 # There are lots of SPI device types, with sensors and memory
1130 # being probably the most widely used ones.
1132 comment "SPI Protocol Masters"
1135 tristate "User mode SPI device driver support"
1137 This supports user mode SPI protocol drivers.
1139 Note that this application programming interface is EXPERIMENTAL
1140 and hence SUBJECT TO CHANGE WITHOUT NOTICE while it stabilizes.
1142 config SPI_LOOPBACK_TEST
1143 tristate "spi loopback test framework support"
1146 This enables the SPI loopback testing framework driver
1148 primarily used for development of spi_master drivers
1149 and to detect regressions
1152 tristate "Infineon TLE62X0 (for power switching)"
1155 SPI driver for Infineon TLE62X0 series line driver chips,
1156 such as the TLE6220, TLE6230 and TLE6240. This provides a
1157 sysfs interface, with each line presented as a kind of GPIO
1158 exposing both switch control and diagnostic feedback.
1161 # Add new SPI protocol masters in alphabetical order above this line
1167 # SLAVE side ... listening to other SPI masters
1171 bool "SPI slave protocol handlers"
1173 If your system has a slave-capable SPI controller, you can enable
1174 slave protocol handlers.
1178 config SPI_SLAVE_TIME
1179 tristate "SPI slave handler reporting boot up time"
1181 SPI slave handler responding with the time of reception of the last
1184 config SPI_SLAVE_SYSTEM_CONTROL
1185 tristate "SPI slave handler controlling system state"
1187 SPI slave handler to allow remote control of system reboot, power
1188 off, halt, and suspend.
1193 def_bool ACPI || OF_DYNAMIC || SPI_SLAVE