drivers/phy/qualcomm/phy-qcom-edp.c

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * Copyright (c) 2017, 2020, The Linux Foundation. All rights reserved.
   4  * Copyright (c) 2021, Linaro Ltd.
   5  */
   6
   7 #include <linux/clk.h>
   8 #include <linux/clk-provider.h>
   9 #include <linux/delay.h>
  10 #include <linux/err.h>
  11 #include <linux/io.h>
  12 #include <linux/iopoll.h>
  13 #include <linux/kernel.h>
  14 #include <linux/module.h>
  15 #include <linux/of.h>
  16 #include <linux/phy/phy.h>
  17 #include <linux/platform_device.h>
  18 #include <linux/regulator/consumer.h>
  19 #include <linux/reset.h>
  20 #include <linux/slab.h>
  21
  22 #include <dt-bindings/phy/phy.h>
  23
  24 #include "phy-qcom-qmp.h"
  25
  26 /* EDP_PHY registers */
  27 #define DP_PHY_CFG                              0x0010
  28 #define DP_PHY_CFG_1                            0x0014
  29 #define DP_PHY_PD_CTL                           0x001c
  30 #define DP_PHY_MODE                             0x0020
  31
  32 #define DP_PHY_AUX_CFG0                         0x0024
  33 #define DP_PHY_AUX_CFG1                         0x0028
  34 #define DP_PHY_AUX_CFG2                         0x002C
  35 #define DP_PHY_AUX_CFG3                         0x0030
  36 #define DP_PHY_AUX_CFG4                         0x0034
  37 #define DP_PHY_AUX_CFG5                         0x0038
  38 #define DP_PHY_AUX_CFG6                         0x003C
  39 #define DP_PHY_AUX_CFG7                         0x0040
  40 #define DP_PHY_AUX_CFG8                         0x0044
  41 #define DP_PHY_AUX_CFG9                         0x0048
  42
  43 #define DP_PHY_AUX_INTERRUPT_MASK               0x0058
  44
  45 #define DP_PHY_VCO_DIV                          0x0074
  46 #define DP_PHY_TX0_TX1_LANE_CTL                 0x007c
  47 #define DP_PHY_TX2_TX3_LANE_CTL                 0x00a0
  48
  49 #define DP_PHY_STATUS                           0x00e0
  50
  51 /* LANE_TXn registers */
  52 #define TXn_CLKBUF_ENABLE                       0x0000
  53 #define TXn_TX_EMP_POST1_LVL                    0x0004
  54
  55 #define TXn_TX_DRV_LVL                          0x0014
  56 #define TXn_TX_DRV_LVL_OFFSET                   0x0018
  57 #define TXn_RESET_TSYNC_EN                      0x001c
  58 #define TXn_LDO_CONFIG                          0x0084
  59 #define TXn_TX_BAND                             0x0028
  60
  61 #define TXn_RES_CODE_LANE_OFFSET_TX0            0x0044
  62 #define TXn_RES_CODE_LANE_OFFSET_TX1            0x0048
  63
  64 #define TXn_TRANSCEIVER_BIAS_EN                 0x0054
  65 #define TXn_HIGHZ_DRVR_EN                       0x0058
  66 #define TXn_TX_POL_INV                          0x005c
  67 #define TXn_LANE_MODE_1                         0x0064
  68
  69 #define TXn_TRAN_DRVR_EMP_EN                    0x0078
  70
  71 struct qcom_edp_cfg {
  72         bool is_dp;
  73
  74         /* DP PHY swing and pre_emphasis tables */
  75         const u8 (*swing_hbr_rbr)[4][4];
  76         const u8 (*swing_hbr3_hbr2)[4][4];
  77         const u8 (*pre_emphasis_hbr_rbr)[4][4];
  78         const u8 (*pre_emphasis_hbr3_hbr2)[4][4];
  79 };
  80
  81 struct qcom_edp {
  82         struct device *dev;
  83         const struct qcom_edp_cfg *cfg;
  84
  85         struct phy *phy;
  86
  87         void __iomem *edp;
  88         void __iomem *tx0;
  89         void __iomem *tx1;
  90         void __iomem *pll;
  91
  92         struct clk_hw dp_link_hw;
  93         struct clk_hw dp_pixel_hw;
  94
  95         struct phy_configure_opts_dp dp_opts;
  96
  97         struct clk_bulk_data clks[2];
  98         struct regulator_bulk_data supplies[2];
  99 };
 100
 101 static const u8 dp_swing_hbr_rbr[4][4] = {
 102         { 0x08, 0x0f, 0x16, 0x1f },
 103         { 0x11, 0x1e, 0x1f, 0xff },
 104         { 0x16, 0x1f, 0xff, 0xff },
 105         { 0x1f, 0xff, 0xff, 0xff }
 106 };
 107
 108 static const u8 dp_pre_emp_hbr_rbr[4][4] = {
 109         { 0x00, 0x0d, 0x14, 0x1a },
 110         { 0x00, 0x0e, 0x15, 0xff },
 111         { 0x00, 0x0e, 0xff, 0xff },
 112         { 0x03, 0xff, 0xff, 0xff }
 113 };
 114
 115 static const u8 dp_swing_hbr2_hbr3[4][4] = {
 116         { 0x02, 0x12, 0x16, 0x1a },
 117         { 0x09, 0x19, 0x1f, 0xff },
 118         { 0x10, 0x1f, 0xff, 0xff },
 119         { 0x1f, 0xff, 0xff, 0xff }
 120 };
 121
 122 static const u8 dp_pre_emp_hbr2_hbr3[4][4] = {
 123         { 0x00, 0x0c, 0x15, 0x1b },
 124         { 0x02, 0x0e, 0x16, 0xff },
 125         { 0x02, 0x11, 0xff, 0xff },
 126         { 0x04, 0xff, 0xff, 0xff }
 127 };
 128
 129 static const struct qcom_edp_cfg dp_phy_cfg = {
 130         .is_dp = true,
 131         .swing_hbr_rbr = &dp_swing_hbr_rbr,
 132         .swing_hbr3_hbr2 = &dp_swing_hbr2_hbr3,
 133         .pre_emphasis_hbr_rbr = &dp_pre_emp_hbr_rbr,
 134         .pre_emphasis_hbr3_hbr2 = &dp_pre_emp_hbr2_hbr3,
 135 };
 136
 137 static const u8 edp_swing_hbr_rbr[4][4] = {
 138         { 0x07, 0x0f, 0x16, 0x1f },
 139         { 0x0d, 0x16, 0x1e, 0xff },
 140         { 0x11, 0x1b, 0xff, 0xff },
 141         { 0x16, 0xff, 0xff, 0xff }
 142 };
 143
 144 static const u8 edp_pre_emp_hbr_rbr[4][4] = {
 145         { 0x05, 0x12, 0x17, 0x1d },
 146         { 0x05, 0x11, 0x18, 0xff },
 147         { 0x06, 0x11, 0xff, 0xff },
 148         { 0x00, 0xff, 0xff, 0xff }
 149 };
 150
 151 static const u8 edp_swing_hbr2_hbr3[4][4] = {
 152         { 0x0b, 0x11, 0x17, 0x1c },
 153         { 0x10, 0x19, 0x1f, 0xff },
 154         { 0x19, 0x1f, 0xff, 0xff },
 155         { 0x1f, 0xff, 0xff, 0xff }
 156 };
 157
 158 static const u8 edp_pre_emp_hbr2_hbr3[4][4] = {
 159         { 0x08, 0x11, 0x17, 0x1b },
 160         { 0x00, 0x0c, 0x13, 0xff },
 161         { 0x05, 0x10, 0xff, 0xff },
 162         { 0x00, 0xff, 0xff, 0xff }
 163 };
 164
 165 static const struct qcom_edp_cfg edp_phy_cfg = {
 166         .is_dp = false,
 167         .swing_hbr_rbr = &edp_swing_hbr_rbr,
 168         .swing_hbr3_hbr2 = &edp_swing_hbr2_hbr3,
 169         .pre_emphasis_hbr_rbr = &edp_pre_emp_hbr_rbr,
 170         .pre_emphasis_hbr3_hbr2 = &edp_pre_emp_hbr2_hbr3,
 171 };
 172
 173 static int qcom_edp_phy_init(struct phy *phy)
 174 {
 175         struct qcom_edp *edp = phy_get_drvdata(phy);
 176         const struct qcom_edp_cfg *cfg = edp->cfg;
 177         int ret;
 178         u8 cfg8;
 179
 180         ret = regulator_bulk_enable(ARRAY_SIZE(edp->supplies), edp->supplies);
 181         if (ret)
 182                 return ret;
 183
 184         ret = clk_bulk_prepare_enable(ARRAY_SIZE(edp->clks), edp->clks);
 185         if (ret)
 186                 goto out_disable_supplies;
 187
 188         writel(DP_PHY_PD_CTL_PWRDN | DP_PHY_PD_CTL_AUX_PWRDN |
 189                DP_PHY_PD_CTL_PLL_PWRDN | DP_PHY_PD_CTL_DP_CLAMP_EN,
 190                edp->edp + DP_PHY_PD_CTL);
 191
 192         /* Turn on BIAS current for PHY/PLL */
 193         writel(0x17, edp->pll + QSERDES_V4_COM_BIAS_EN_CLKBUFLR_EN);
 194
 195         writel(DP_PHY_PD_CTL_PSR_PWRDN, edp->edp + DP_PHY_PD_CTL);
 196         msleep(20);
 197
 198         writel(DP_PHY_PD_CTL_PWRDN | DP_PHY_PD_CTL_AUX_PWRDN |
 199                DP_PHY_PD_CTL_LANE_0_1_PWRDN | DP_PHY_PD_CTL_LANE_2_3_PWRDN |
 200                DP_PHY_PD_CTL_PLL_PWRDN | DP_PHY_PD_CTL_DP_CLAMP_EN,
 201                edp->edp + DP_PHY_PD_CTL);
 202
 203         if (cfg && cfg->is_dp)
 204                 cfg8 = 0xb7;
 205         else
 206                 cfg8 = 0x37;
 207
 208         writel(0xfc, edp->edp + DP_PHY_MODE);
 209
 210         writel(0x00, edp->edp + DP_PHY_AUX_CFG0);
 211         writel(0x13, edp->edp + DP_PHY_AUX_CFG1);
 212         writel(0x24, edp->edp + DP_PHY_AUX_CFG2);
 213         writel(0x00, edp->edp + DP_PHY_AUX_CFG3);
 214         writel(0x0a, edp->edp + DP_PHY_AUX_CFG4);
 215         writel(0x26, edp->edp + DP_PHY_AUX_CFG5);
 216         writel(0x0a, edp->edp + DP_PHY_AUX_CFG6);
 217         writel(0x03, edp->edp + DP_PHY_AUX_CFG7);
 218         writel(cfg8, edp->edp + DP_PHY_AUX_CFG8);
 219         writel(0x03, edp->edp + DP_PHY_AUX_CFG9);
 220
 221         writel(PHY_AUX_STOP_ERR_MASK | PHY_AUX_DEC_ERR_MASK |
 222                PHY_AUX_SYNC_ERR_MASK | PHY_AUX_ALIGN_ERR_MASK |
 223                PHY_AUX_REQ_ERR_MASK, edp->edp + DP_PHY_AUX_INTERRUPT_MASK);
 224
 225         msleep(20);
 226
 227         return 0;
 228
 229 out_disable_supplies:
 230         regulator_bulk_disable(ARRAY_SIZE(edp->supplies), edp->supplies);
 231
 232         return ret;
 233 }
 234
 235 static int qcom_edp_set_voltages(struct qcom_edp *edp, const struct phy_configure_opts_dp *dp_opts)
 236 {
 237         const struct qcom_edp_cfg *cfg = edp->cfg;
 238         unsigned int v_level = 0;
 239         unsigned int p_level = 0;
 240         u8 ldo_config;
 241         u8 swing;
 242         u8 emph;
 243         int i;
 244
 245         if (!cfg)
 246                 return 0;
 247
 248         for (i = 0; i < dp_opts->lanes; i++) {
 249                 v_level = max(v_level, dp_opts->voltage[i]);
 250                 p_level = max(p_level, dp_opts->pre[i]);
 251         }
 252
 253         if (dp_opts->link_rate <= 2700) {
 254                 swing = (*cfg->swing_hbr_rbr)[v_level][p_level];
 255                 emph = (*cfg->pre_emphasis_hbr_rbr)[v_level][p_level];
 256         } else {
 257                 swing = (*cfg->swing_hbr3_hbr2)[v_level][p_level];
 258                 emph = (*cfg->pre_emphasis_hbr3_hbr2)[v_level][p_level];
 259         }
 260
 261         if (swing == 0xff || emph == 0xff)
 262                 return -EINVAL;
 263
 264         ldo_config = (cfg && cfg->is_dp) ? 0x1 : 0x0;
 265
 266         writel(ldo_config, edp->tx0 + TXn_LDO_CONFIG);
 267         writel(swing, edp->tx0 + TXn_TX_DRV_LVL);
 268         writel(emph, edp->tx0 + TXn_TX_EMP_POST1_LVL);
 269
 270         writel(ldo_config, edp->tx1 + TXn_LDO_CONFIG);
 271         writel(swing, edp->tx1 + TXn_TX_DRV_LVL);
 272         writel(emph, edp->tx1 + TXn_TX_EMP_POST1_LVL);
 273
 274         return 0;
 275 }
 276
 277 static int qcom_edp_phy_configure(struct phy *phy, union phy_configure_opts *opts)
 278 {
 279         const struct phy_configure_opts_dp *dp_opts = &opts->dp;
 280         struct qcom_edp *edp = phy_get_drvdata(phy);
 281         int ret = 0;
 282
 283         memcpy(&edp->dp_opts, dp_opts, sizeof(*dp_opts));
 284
 285         if (dp_opts->set_voltages)
 286                 ret = qcom_edp_set_voltages(edp, dp_opts);
 287
 288         return ret;
 289 }
 290
 291 static int qcom_edp_configure_ssc(const struct qcom_edp *edp)
 292 {
 293         const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts;
 294         u32 step1;
 295         u32 step2;
 296
 297         switch (dp_opts->link_rate) {
 298         case 1620:
 299         case 2700:
 300         case 8100:
 301                 step1 = 0x45;
 302                 step2 = 0x06;
 303                 break;
 304
 305         case 5400:
 306                 step1 = 0x5c;
 307                 step2 = 0x08;
 308                 break;
 309
 310         default:
 311                 /* Other link rates aren't supported */
 312                 return -EINVAL;
 313         }
 314
 315         writel(0x01, edp->pll + QSERDES_V4_COM_SSC_EN_CENTER);
 316         writel(0x00, edp->pll + QSERDES_V4_COM_SSC_ADJ_PER1);
 317         writel(0x36, edp->pll + QSERDES_V4_COM_SSC_PER1);
 318         writel(0x01, edp->pll + QSERDES_V4_COM_SSC_PER2);
 319         writel(step1, edp->pll + QSERDES_V4_COM_SSC_STEP_SIZE1_MODE0);
 320         writel(step2, edp->pll + QSERDES_V4_COM_SSC_STEP_SIZE2_MODE0);
 321
 322         return 0;
 323 }
 324
 325 static int qcom_edp_configure_pll(const struct qcom_edp *edp)
 326 {
 327         const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts;
 328         u32 div_frac_start2_mode0;
 329         u32 div_frac_start3_mode0;
 330         u32 dec_start_mode0;
 331         u32 lock_cmp1_mode0;
 332         u32 lock_cmp2_mode0;
 333         u32 hsclk_sel;
 334
 335         switch (dp_opts->link_rate) {
 336         case 1620:
 337                 hsclk_sel = 0x5;
 338                 dec_start_mode0 = 0x69;
 339                 div_frac_start2_mode0 = 0x80;
 340                 div_frac_start3_mode0 = 0x07;
 341                 lock_cmp1_mode0 = 0x6f;
 342                 lock_cmp2_mode0 = 0x08;
 343                 break;
 344
 345         case 2700:
 346                 hsclk_sel = 0x3;
 347                 dec_start_mode0 = 0x69;
 348                 div_frac_start2_mode0 = 0x80;
 349                 div_frac_start3_mode0 = 0x07;
 350                 lock_cmp1_mode0 = 0x0f;
 351                 lock_cmp2_mode0 = 0x0e;
 352                 break;
 353
 354         case 5400:
 355                 hsclk_sel = 0x1;
 356                 dec_start_mode0 = 0x8c;
 357                 div_frac_start2_mode0 = 0x00;
 358                 div_frac_start3_mode0 = 0x0a;
 359                 lock_cmp1_mode0 = 0x1f;
 360                 lock_cmp2_mode0 = 0x1c;
 361                 break;
 362
 363         case 8100:
 364                 hsclk_sel = 0x0;
 365                 dec_start_mode0 = 0x69;
 366                 div_frac_start2_mode0 = 0x80;
 367                 div_frac_start3_mode0 = 0x07;
 368                 lock_cmp1_mode0 = 0x2f;
 369                 lock_cmp2_mode0 = 0x2a;
 370                 break;
 371
 372         default:
 373                 /* Other link rates aren't supported */
 374                 return -EINVAL;
 375         }
 376
 377         writel(0x01, edp->pll + QSERDES_V4_COM_SVS_MODE_CLK_SEL);
 378         writel(0x0b, edp->pll + QSERDES_V4_COM_SYSCLK_EN_SEL);
 379         writel(0x02, edp->pll + QSERDES_V4_COM_SYS_CLK_CTRL);
 380         writel(0x0c, edp->pll + QSERDES_V4_COM_CLK_ENABLE1);
 381         writel(0x06, edp->pll + QSERDES_V4_COM_SYSCLK_BUF_ENABLE);
 382         writel(0x30, edp->pll + QSERDES_V4_COM_CLK_SELECT);
 383         writel(hsclk_sel, edp->pll + QSERDES_V4_COM_HSCLK_SEL);
 384         writel(0x0f, edp->pll + QSERDES_V4_COM_PLL_IVCO);
 385         writel(0x08, edp->pll + QSERDES_V4_COM_LOCK_CMP_EN);
 386         writel(0x36, edp->pll + QSERDES_V4_COM_PLL_CCTRL_MODE0);
 387         writel(0x16, edp->pll + QSERDES_V4_COM_PLL_RCTRL_MODE0);
 388         writel(0x06, edp->pll + QSERDES_V4_COM_CP_CTRL_MODE0);
 389         writel(dec_start_mode0, edp->pll + QSERDES_V4_COM_DEC_START_MODE0);
 390         writel(0x00, edp->pll + QSERDES_V4_COM_DIV_FRAC_START1_MODE0);
 391         writel(div_frac_start2_mode0, edp->pll + QSERDES_V4_COM_DIV_FRAC_START2_MODE0);
 392         writel(div_frac_start3_mode0, edp->pll + QSERDES_V4_COM_DIV_FRAC_START3_MODE0);
 393         writel(0x02, edp->pll + QSERDES_V4_COM_CMN_CONFIG);
 394         writel(0x3f, edp->pll + QSERDES_V4_COM_INTEGLOOP_GAIN0_MODE0);
 395         writel(0x00, edp->pll + QSERDES_V4_COM_INTEGLOOP_GAIN1_MODE0);
 396         writel(0x00, edp->pll + QSERDES_V4_COM_VCO_TUNE_MAP);
 397         writel(lock_cmp1_mode0, edp->pll + QSERDES_V4_COM_LOCK_CMP1_MODE0);
 398         writel(lock_cmp2_mode0, edp->pll + QSERDES_V4_COM_LOCK_CMP2_MODE0);
 399
 400         writel(0x0a, edp->pll + QSERDES_V4_COM_BG_TIMER);
 401         writel(0x14, edp->pll + QSERDES_V4_COM_CORECLK_DIV_MODE0);
 402         writel(0x00, edp->pll + QSERDES_V4_COM_VCO_TUNE_CTRL);
 403         writel(0x17, edp->pll + QSERDES_V4_COM_BIAS_EN_CLKBUFLR_EN);
 404         writel(0x0f, edp->pll + QSERDES_V4_COM_CORE_CLK_EN);
 405         writel(0xa0, edp->pll + QSERDES_V4_COM_VCO_TUNE1_MODE0);
 406         writel(0x03, edp->pll + QSERDES_V4_COM_VCO_TUNE2_MODE0);
 407
 408         return 0;
 409 }
 410
 411 static int qcom_edp_set_vco_div(const struct qcom_edp *edp, unsigned long *pixel_freq)
 412 {
 413         const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts;
 414         u32 vco_div;
 415
 416         switch (dp_opts->link_rate) {
 417         case 1620:
 418                 vco_div = 0x1;
 419                 *pixel_freq = 1620000000UL / 2;
 420                 break;
 421
 422         case 2700:
 423                 vco_div = 0x1;
 424                 *pixel_freq = 2700000000UL / 2;
 425                 break;
 426
 427         case 5400:
 428                 vco_div = 0x2;
 429                 *pixel_freq = 5400000000UL / 4;
 430                 break;
 431
 432         case 8100:
 433                 vco_div = 0x0;
 434                 *pixel_freq = 8100000000UL / 6;
 435                 break;
 436
 437         default:
 438                 /* Other link rates aren't supported */
 439                 return -EINVAL;
 440         }
 441
 442         writel(vco_div, edp->edp + DP_PHY_VCO_DIV);
 443
 444         return 0;
 445 }
 446
 447 static int qcom_edp_phy_power_on(struct phy *phy)
 448 {
 449         const struct qcom_edp *edp = phy_get_drvdata(phy);
 450         const struct qcom_edp_cfg *cfg = edp->cfg;
 451         u32 bias0_en, drvr0_en, bias1_en, drvr1_en;
 452         unsigned long pixel_freq;
 453         u8 ldo_config;
 454         int timeout;
 455         int ret;
 456         u32 val;
 457         u8 cfg1;
 458
 459         writel(DP_PHY_PD_CTL_PWRDN | DP_PHY_PD_CTL_AUX_PWRDN |
 460                DP_PHY_PD_CTL_LANE_0_1_PWRDN | DP_PHY_PD_CTL_LANE_2_3_PWRDN |
 461                DP_PHY_PD_CTL_PLL_PWRDN | DP_PHY_PD_CTL_DP_CLAMP_EN,
 462                edp->edp + DP_PHY_PD_CTL);
 463         writel(0xfc, edp->edp + DP_PHY_MODE);
 464
 465         timeout = readl_poll_timeout(edp->pll + QSERDES_V4_COM_CMN_STATUS,
 466                                      val, val & BIT(7), 5, 200);
 467         if (timeout)
 468                 return timeout;
 469
 470
 471         ldo_config = (cfg && cfg->is_dp) ? 0x1 : 0x0;
 472
 473         writel(ldo_config, edp->tx0 + TXn_LDO_CONFIG);
 474         writel(ldo_config, edp->tx1 + TXn_LDO_CONFIG);
 475         writel(0x00, edp->tx0 + TXn_LANE_MODE_1);
 476         writel(0x00, edp->tx1 + TXn_LANE_MODE_1);
 477
 478         if (edp->dp_opts.ssc) {
 479                 ret = qcom_edp_configure_ssc(edp);
 480                 if (ret)
 481                         return ret;
 482         }
 483
 484         ret = qcom_edp_configure_pll(edp);
 485         if (ret)
 486                 return ret;
 487
 488         /* TX Lane configuration */
 489         writel(0x05, edp->edp + DP_PHY_TX0_TX1_LANE_CTL);
 490         writel(0x05, edp->edp + DP_PHY_TX2_TX3_LANE_CTL);
 491
 492         /* TX-0 register configuration */
 493         writel(0x03, edp->tx0 + TXn_TRANSCEIVER_BIAS_EN);
 494         writel(0x0f, edp->tx0 + TXn_CLKBUF_ENABLE);
 495         writel(0x03, edp->tx0 + TXn_RESET_TSYNC_EN);
 496         writel(0x01, edp->tx0 + TXn_TRAN_DRVR_EMP_EN);
 497         writel(0x04, edp->tx0 + TXn_TX_BAND);
 498
 499         /* TX-1 register configuration */
 500         writel(0x03, edp->tx1 + TXn_TRANSCEIVER_BIAS_EN);
 501         writel(0x0f, edp->tx1 + TXn_CLKBUF_ENABLE);
 502         writel(0x03, edp->tx1 + TXn_RESET_TSYNC_EN);
 503         writel(0x01, edp->tx1 + TXn_TRAN_DRVR_EMP_EN);
 504         writel(0x04, edp->tx1 + TXn_TX_BAND);
 505
 506         ret = qcom_edp_set_vco_div(edp, &pixel_freq);
 507         if (ret)
 508                 return ret;
 509
 510         writel(0x01, edp->edp + DP_PHY_CFG);
 511         writel(0x05, edp->edp + DP_PHY_CFG);
 512         writel(0x01, edp->edp + DP_PHY_CFG);
 513         writel(0x09, edp->edp + DP_PHY_CFG);
 514
 515         writel(0x20, edp->pll + QSERDES_V4_COM_RESETSM_CNTRL);
 516
 517         timeout = readl_poll_timeout(edp->pll + QSERDES_V4_COM_C_READY_STATUS,
 518                                      val, val & BIT(0), 500, 10000);
 519         if (timeout)
 520                 return timeout;
 521
 522         writel(0x19, edp->edp + DP_PHY_CFG);
 523         writel(0x1f, edp->tx0 + TXn_HIGHZ_DRVR_EN);
 524         writel(0x04, edp->tx0 + TXn_HIGHZ_DRVR_EN);
 525         writel(0x00, edp->tx0 + TXn_TX_POL_INV);
 526         writel(0x1f, edp->tx1 + TXn_HIGHZ_DRVR_EN);
 527         writel(0x04, edp->tx1 + TXn_HIGHZ_DRVR_EN);
 528         writel(0x00, edp->tx1 + TXn_TX_POL_INV);
 529         writel(0x10, edp->tx0 + TXn_TX_DRV_LVL_OFFSET);
 530         writel(0x10, edp->tx1 + TXn_TX_DRV_LVL_OFFSET);
 531         writel(0x11, edp->tx0 + TXn_RES_CODE_LANE_OFFSET_TX0);
 532         writel(0x11, edp->tx0 + TXn_RES_CODE_LANE_OFFSET_TX1);
 533         writel(0x11, edp->tx1 + TXn_RES_CODE_LANE_OFFSET_TX0);
 534         writel(0x11, edp->tx1 + TXn_RES_CODE_LANE_OFFSET_TX1);
 535
 536         writel(0x10, edp->tx0 + TXn_TX_EMP_POST1_LVL);
 537         writel(0x10, edp->tx1 + TXn_TX_EMP_POST1_LVL);
 538         writel(0x1f, edp->tx0 + TXn_TX_DRV_LVL);
 539         writel(0x1f, edp->tx1 + TXn_TX_DRV_LVL);
 540
 541         if (edp->dp_opts.lanes == 1) {
 542                 bias0_en = 0x01;
 543                 bias1_en = 0x00;
 544                 drvr0_en = 0x06;
 545                 drvr1_en = 0x07;
 546                 cfg1 = 0x1;
 547         } else if (edp->dp_opts.lanes == 2) {
 548                 bias0_en = 0x03;
 549                 bias1_en = 0x00;
 550                 drvr0_en = 0x04;
 551                 drvr1_en = 0x07;
 552                 cfg1 = 0x3;
 553         } else {
 554                 bias0_en = 0x03;
 555                 bias1_en = 0x03;
 556                 drvr0_en = 0x04;
 557                 drvr1_en = 0x04;
 558                 cfg1 = 0xf;
 559         }
 560
 561         writel(drvr0_en, edp->tx0 + TXn_HIGHZ_DRVR_EN);
 562         writel(bias0_en, edp->tx0 + TXn_TRANSCEIVER_BIAS_EN);
 563         writel(drvr1_en, edp->tx1 + TXn_HIGHZ_DRVR_EN);
 564         writel(bias1_en, edp->tx1 + TXn_TRANSCEIVER_BIAS_EN);
 565         writel(cfg1, edp->edp + DP_PHY_CFG_1);
 566
 567         writel(0x18, edp->edp + DP_PHY_CFG);
 568         usleep_range(100, 1000);
 569
 570         writel(0x19, edp->edp + DP_PHY_CFG);
 571
 572         ret = readl_poll_timeout(edp->edp + DP_PHY_STATUS,
 573                                  val, val & BIT(1), 500, 10000);
 574         if (ret)
 575                 return ret;
 576
 577         clk_set_rate(edp->dp_link_hw.clk, edp->dp_opts.link_rate * 100000);
 578         clk_set_rate(edp->dp_pixel_hw.clk, pixel_freq);
 579
 580         return 0;
 581 }
 582
 583 static int qcom_edp_phy_power_off(struct phy *phy)
 584 {
 585         const struct qcom_edp *edp = phy_get_drvdata(phy);
 586
 587         writel(DP_PHY_PD_CTL_PSR_PWRDN, edp->edp + DP_PHY_PD_CTL);
 588
 589         return 0;
 590 }
 591
 592 static int qcom_edp_phy_exit(struct phy *phy)
 593 {
 594         struct qcom_edp *edp = phy_get_drvdata(phy);
 595
 596         clk_bulk_disable_unprepare(ARRAY_SIZE(edp->clks), edp->clks);
 597         regulator_bulk_disable(ARRAY_SIZE(edp->supplies), edp->supplies);
 598
 599         return 0;
 600 }
 601
 602 static const struct phy_ops qcom_edp_ops = {
 603         .init           = qcom_edp_phy_init,
 604         .configure      = qcom_edp_phy_configure,
 605         .power_on       = qcom_edp_phy_power_on,
 606         .power_off      = qcom_edp_phy_power_off,
 607         .exit           = qcom_edp_phy_exit,
 608         .owner          = THIS_MODULE,
 609 };
 610
 611 /*
 612  * Embedded Display Port PLL driver block diagram for branch clocks
 613  *
 614  *              +------------------------------+
 615  *              |        EDP_VCO_CLK           |
 616  *              |                              |
 617  *              |    +-------------------+     |
 618  *              |    |  (EDP PLL/VCO)    |     |
 619  *              |    +---------+---------+     |
 620  *              |              v               |
 621  *              |   +----------+-----------+   |
 622  *              |   | hsclk_divsel_clk_src |   |
 623  *              |   +----------+-----------+   |
 624  *              +------------------------------+
 625  *                              |
 626  *          +---------<---------v------------>----------+
 627  *          |                                           |
 628  * +--------v----------------+                          |
 629  * |   edp_phy_pll_link_clk  |                          |
 630  * |     link_clk            |                          |
 631  * +--------+----------------+                          |
 632  *          |                                           |
 633  *          |                                           |
 634  *          v                                           v
 635  * Input to DISPCC block                                |
 636  * for link clk, crypto clk                             |
 637  * and interface clock                                  |
 638  *                                                      |
 639  *                                                      |
 640  *      +--------<------------+-----------------+---<---+
 641  *      |                     |                 |
 642  * +----v---------+  +--------v-----+  +--------v------+
 643  * | vco_divided  |  | vco_divided  |  | vco_divided   |
 644  * |    _clk_src  |  |    _clk_src  |  |    _clk_src   |
 645  * |              |  |              |  |               |
 646  * |divsel_six    |  |  divsel_two  |  |  divsel_four  |
 647  * +-------+------+  +-----+--------+  +--------+------+
 648  *         |                 |                  |
 649  *         v---->----------v-------------<------v
 650  *                         |
 651  *              +----------+-----------------+
 652  *              |   edp_phy_pll_vco_div_clk  |
 653  *              +---------+------------------+
 654  *                        |
 655  *                        v
 656  *              Input to DISPCC block
 657  *              for EDP pixel clock
 658  *
 659  */
 660 static int qcom_edp_dp_pixel_clk_determine_rate(struct clk_hw *hw,
 661                                                 struct clk_rate_request *req)
 662 {
 663         switch (req->rate) {
 664         case 1620000000UL / 2:
 665         case 2700000000UL / 2:
 666         /* 5.4 and 8.1 GHz are same link rate as 2.7GHz, i.e. div 4 and div 6 */
 667                 return 0;
 668
 669         default:
 670                 return -EINVAL;
 671         }
 672 }
 673
 674 static unsigned long
 675 qcom_edp_dp_pixel_clk_recalc_rate(struct clk_hw *hw, unsigned long parent_rate)
 676 {
 677         const struct qcom_edp *edp = container_of(hw, struct qcom_edp, dp_pixel_hw);
 678         const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts;
 679
 680         switch (dp_opts->link_rate) {
 681         case 1620:
 682                 return 1620000000UL / 2;
 683         case 2700:
 684                 return 2700000000UL / 2;
 685         case 5400:
 686                 return 5400000000UL / 4;
 687         case 8100:
 688                 return 8100000000UL / 6;
 689         default:
 690                 return 0;
 691         }
 692 }
 693
 694 static const struct clk_ops qcom_edp_dp_pixel_clk_ops = {
 695         .determine_rate = qcom_edp_dp_pixel_clk_determine_rate,
 696         .recalc_rate = qcom_edp_dp_pixel_clk_recalc_rate,
 697 };
 698
 699 static int qcom_edp_dp_link_clk_determine_rate(struct clk_hw *hw,
 700                                                struct clk_rate_request *req)
 701 {
 702         switch (req->rate) {
 703         case 162000000:
 704         case 270000000:
 705         case 540000000:
 706         case 810000000:
 707                 return 0;
 708
 709         default:
 710                 return -EINVAL;
 711         }
 712 }
 713
 714 static unsigned long
 715 qcom_edp_dp_link_clk_recalc_rate(struct clk_hw *hw, unsigned long parent_rate)
 716 {
 717         const struct qcom_edp *edp = container_of(hw, struct qcom_edp, dp_link_hw);
 718         const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts;
 719
 720         switch (dp_opts->link_rate) {
 721         case 1620:
 722         case 2700:
 723         case 5400:
 724         case 8100:
 725                 return dp_opts->link_rate * 100000;
 726
 727         default:
 728                 return 0;
 729         }
 730 }
 731
 732 static const struct clk_ops qcom_edp_dp_link_clk_ops = {
 733         .determine_rate = qcom_edp_dp_link_clk_determine_rate,
 734         .recalc_rate = qcom_edp_dp_link_clk_recalc_rate,
 735 };
 736
 737 static int qcom_edp_clks_register(struct qcom_edp *edp, struct device_node *np)
 738 {
 739         struct clk_hw_onecell_data *data;
 740         struct clk_init_data init = { };
 741         char name[64];
 742         int ret;
 743
 744         data = devm_kzalloc(edp->dev, struct_size(data, hws, 2), GFP_KERNEL);
 745         if (!data)
 746                 return -ENOMEM;
 747         data->num = 2;
 748
 749         snprintf(name, sizeof(name), "%s::link_clk", dev_name(edp->dev));
 750         init.ops = &qcom_edp_dp_link_clk_ops;
 751         init.name = name;
 752         edp->dp_link_hw.init = &init;
 753         ret = devm_clk_hw_register(edp->dev, &edp->dp_link_hw);
 754         if (ret)
 755                 return ret;
 756
 757         snprintf(name, sizeof(name), "%s::vco_div_clk", dev_name(edp->dev));
 758         init.ops = &qcom_edp_dp_pixel_clk_ops;
 759         init.name = name;
 760         edp->dp_pixel_hw.init = &init;
 761         ret = devm_clk_hw_register(edp->dev, &edp->dp_pixel_hw);
 762         if (ret)
 763                 return ret;
 764
 765         data->hws[0] = &edp->dp_link_hw;
 766         data->hws[1] = &edp->dp_pixel_hw;
 767
 768         return devm_of_clk_add_hw_provider(edp->dev, of_clk_hw_onecell_get, data);
 769 }
 770
 771 static int qcom_edp_phy_probe(struct platform_device *pdev)
 772 {
 773         struct phy_provider *phy_provider;
 774         struct device *dev = &pdev->dev;
 775         struct qcom_edp *edp;
 776         int ret;
 777
 778         edp = devm_kzalloc(dev, sizeof(*edp), GFP_KERNEL);
 779         if (!edp)
 780                 return -ENOMEM;
 781
 782         edp->dev = dev;
 783         edp->cfg = of_device_get_match_data(&pdev->dev);
 784
 785         edp->edp = devm_platform_ioremap_resource(pdev, 0);
 786         if (IS_ERR(edp->edp))
 787                 return PTR_ERR(edp->edp);
 788
 789         edp->tx0 = devm_platform_ioremap_resource(pdev, 1);
 790         if (IS_ERR(edp->tx0))
 791                 return PTR_ERR(edp->tx0);
 792
 793         edp->tx1 = devm_platform_ioremap_resource(pdev, 2);
 794         if (IS_ERR(edp->tx1))
 795                 return PTR_ERR(edp->tx1);
 796
 797         edp->pll = devm_platform_ioremap_resource(pdev, 3);
 798         if (IS_ERR(edp->pll))
 799                 return PTR_ERR(edp->pll);
 800
 801         edp->clks[0].id = "aux";
 802         edp->clks[1].id = "cfg_ahb";
 803         ret = devm_clk_bulk_get(dev, ARRAY_SIZE(edp->clks), edp->clks);
 804         if (ret)
 805                 return ret;
 806
 807         edp->supplies[0].supply = "vdda-phy";
 808         edp->supplies[1].supply = "vdda-pll";
 809         ret = devm_regulator_bulk_get(dev, ARRAY_SIZE(edp->supplies), edp->supplies);
 810         if (ret)
 811                 return ret;
 812
 813         ret = regulator_set_load(edp->supplies[0].consumer, 21800); /* 1.2 V vdda-phy */
 814         if (ret) {
 815                 dev_err(dev, "failed to set load at %s\n", edp->supplies[0].supply);
 816                 return ret;
 817         }
 818
 819         ret = regulator_set_load(edp->supplies[1].consumer, 36000); /* 0.9 V vdda-pll */
 820         if (ret) {
 821                 dev_err(dev, "failed to set load at %s\n", edp->supplies[1].supply);
 822                 return ret;
 823         }
 824
 825         ret = qcom_edp_clks_register(edp, pdev->dev.of_node);
 826         if (ret)
 827                 return ret;
 828
 829         edp->phy = devm_phy_create(dev, pdev->dev.of_node, &qcom_edp_ops);
 830         if (IS_ERR(edp->phy)) {
 831                 dev_err(dev, "failed to register phy\n");
 832                 return PTR_ERR(edp->phy);
 833         }
 834
 835         phy_set_drvdata(edp->phy, edp);
 836
 837         phy_provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate);
 838         return PTR_ERR_OR_ZERO(phy_provider);
 839 }
 840
 841 static const struct of_device_id qcom_edp_phy_match_table[] = {
 842         { .compatible = "qcom,sc7280-edp-phy" },
 843         { .compatible = "qcom,sc8180x-edp-phy" },
 844         { .compatible = "qcom,sc8280xp-dp-phy", .data = &dp_phy_cfg },
 845         { .compatible = "qcom,sc8280xp-edp-phy", .data = &edp_phy_cfg },
 846         { }
 847 };
 848 MODULE_DEVICE_TABLE(of, qcom_edp_phy_match_table);
 849
 850 static struct platform_driver qcom_edp_phy_driver = {
 851         .probe          = qcom_edp_phy_probe,
 852         .driver = {
 853                 .name   = "qcom-edp-phy",
 854                 .of_match_table = qcom_edp_phy_match_table,
 855         },
 856 };
 857
 858 module_platform_driver(qcom_edp_phy_driver);
 859
 860 MODULE_AUTHOR("Bjorn Andersson <bjorn.andersson@linaro.org>");
 861 MODULE_DESCRIPTION("Qualcomm eDP QMP PHY driver");
 862 MODULE_LICENSE("GPL v2");