2 * Copyright (c) 2004-2008 Reyk Floeter <reyk@openbsd.org>
3 * Copyright (c) 2006-2008 Nick Kossifidis <mickflemm@gmail.com>
5 * Permission to use, copy, modify, and distribute this software for any
6 * purpose with or without fee is hereby granted, provided that the above
7 * copyright notice and this permission notice appear in all copies.
9 * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
10 * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
11 * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR
12 * ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
13 * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN
14 * ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF
15 * OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
19 /*************************************\
20 * DMA and interrupt masking functions *
21 \*************************************/
24 * DOC: DMA and interrupt masking functions
26 * Here we setup descriptor pointers (rxdp/txdp) start/stop dma engine and
27 * handle queue setup for 5210 chipset (rest are handled on qcu.c).
28 * Also we setup interrupt mask register (IMR) and read the various interrupt
29 * status registers (ISR).
32 #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
44 * ath5k_hw_start_rx_dma() - Start DMA receive
45 * @ah: The &struct ath5k_hw
48 ath5k_hw_start_rx_dma(struct ath5k_hw *ah)
50 ath5k_hw_reg_write(ah, AR5K_CR_RXE, AR5K_CR);
51 ath5k_hw_reg_read(ah, AR5K_CR);
55 * ath5k_hw_stop_rx_dma() - Stop DMA receive
56 * @ah: The &struct ath5k_hw
59 ath5k_hw_stop_rx_dma(struct ath5k_hw *ah)
63 ath5k_hw_reg_write(ah, AR5K_CR_RXD, AR5K_CR);
66 * It may take some time to disable the DMA receive unit
68 for (i = 1000; i > 0 &&
69 (ath5k_hw_reg_read(ah, AR5K_CR) & AR5K_CR_RXE) != 0;
74 ATH5K_DBG(ah, ATH5K_DEBUG_DMA,
75 "failed to stop RX DMA !\n");
77 return i ? 0 : -EBUSY;
81 * ath5k_hw_get_rxdp() - Get RX Descriptor's address
82 * @ah: The &struct ath5k_hw
85 ath5k_hw_get_rxdp(struct ath5k_hw *ah)
87 return ath5k_hw_reg_read(ah, AR5K_RXDP);
91 * ath5k_hw_set_rxdp() - Set RX Descriptor's address
92 * @ah: The &struct ath5k_hw
93 * @phys_addr: RX descriptor address
95 * Returns -EIO if rx is active
98 ath5k_hw_set_rxdp(struct ath5k_hw *ah, u32 phys_addr)
100 if (ath5k_hw_reg_read(ah, AR5K_CR) & AR5K_CR_RXE) {
101 ATH5K_DBG(ah, ATH5K_DEBUG_DMA,
102 "tried to set RXDP while rx was active !\n");
106 ath5k_hw_reg_write(ah, phys_addr, AR5K_RXDP);
116 * ath5k_hw_start_tx_dma() - Start DMA transmit for a specific queue
117 * @ah: The &struct ath5k_hw
118 * @queue: The hw queue number
120 * Start DMA transmit for a specific queue and since 5210 doesn't have
121 * QCU/DCU, set up queue parameters for 5210 here based on queue type (one
122 * queue for normal data and one queue for beacons). For queue setup
123 * on newer chips check out qcu.c. Returns -EINVAL if queue number is out
124 * of range or if queue is already disabled.
126 * NOTE: Must be called after setting up tx control descriptor for that
130 ath5k_hw_start_tx_dma(struct ath5k_hw *ah, unsigned int queue)
134 AR5K_ASSERT_ENTRY(queue, ah->ah_capabilities.cap_queues.q_tx_num);
136 /* Return if queue is declared inactive */
137 if (ah->ah_txq[queue].tqi_type == AR5K_TX_QUEUE_INACTIVE)
140 if (ah->ah_version == AR5K_AR5210) {
141 tx_queue = ath5k_hw_reg_read(ah, AR5K_CR);
144 * Set the queue by type on 5210
146 switch (ah->ah_txq[queue].tqi_type) {
147 case AR5K_TX_QUEUE_DATA:
148 tx_queue |= AR5K_CR_TXE0 & ~AR5K_CR_TXD0;
150 case AR5K_TX_QUEUE_BEACON:
151 tx_queue |= AR5K_CR_TXE1 & ~AR5K_CR_TXD1;
152 ath5k_hw_reg_write(ah, AR5K_BCR_TQ1V | AR5K_BCR_BDMAE,
155 case AR5K_TX_QUEUE_CAB:
156 tx_queue |= AR5K_CR_TXE1 & ~AR5K_CR_TXD1;
157 ath5k_hw_reg_write(ah, AR5K_BCR_TQ1FV | AR5K_BCR_TQ1V |
158 AR5K_BCR_BDMAE, AR5K_BSR);
164 ath5k_hw_reg_write(ah, tx_queue, AR5K_CR);
165 ath5k_hw_reg_read(ah, AR5K_CR);
167 /* Return if queue is disabled */
168 if (AR5K_REG_READ_Q(ah, AR5K_QCU_TXD, queue))
172 AR5K_REG_WRITE_Q(ah, AR5K_QCU_TXE, queue);
179 * ath5k_hw_stop_tx_dma() - Stop DMA transmit on a specific queue
180 * @ah: The &struct ath5k_hw
181 * @queue: The hw queue number
183 * Stop DMA transmit on a specific hw queue and drain queue so we don't
184 * have any pending frames. Returns -EBUSY if we still have pending frames,
185 * -EINVAL if queue number is out of range or inactive.
188 ath5k_hw_stop_tx_dma(struct ath5k_hw *ah, unsigned int queue)
191 u32 tx_queue, pending;
193 AR5K_ASSERT_ENTRY(queue, ah->ah_capabilities.cap_queues.q_tx_num);
195 /* Return if queue is declared inactive */
196 if (ah->ah_txq[queue].tqi_type == AR5K_TX_QUEUE_INACTIVE)
199 if (ah->ah_version == AR5K_AR5210) {
200 tx_queue = ath5k_hw_reg_read(ah, AR5K_CR);
205 switch (ah->ah_txq[queue].tqi_type) {
206 case AR5K_TX_QUEUE_DATA:
207 tx_queue |= AR5K_CR_TXD0 & ~AR5K_CR_TXE0;
209 case AR5K_TX_QUEUE_BEACON:
210 case AR5K_TX_QUEUE_CAB:
212 tx_queue |= AR5K_CR_TXD1 & ~AR5K_CR_TXD1;
213 ath5k_hw_reg_write(ah, 0, AR5K_BSR);
220 ath5k_hw_reg_write(ah, tx_queue, AR5K_CR);
221 ath5k_hw_reg_read(ah, AR5K_CR);
225 * Enable DCU early termination to quickly
226 * flush any pending frames from QCU
228 AR5K_REG_ENABLE_BITS(ah, AR5K_QUEUE_MISC(queue),
229 AR5K_QCU_MISC_DCU_EARLY);
232 * Schedule TX disable and wait until queue is empty
234 AR5K_REG_WRITE_Q(ah, AR5K_QCU_TXD, queue);
236 /* Wait for queue to stop */
237 for (i = 1000; i > 0 &&
238 (AR5K_REG_READ_Q(ah, AR5K_QCU_TXE, queue) != 0);
242 if (AR5K_REG_READ_Q(ah, AR5K_QCU_TXE, queue))
243 ATH5K_DBG(ah, ATH5K_DEBUG_DMA,
244 "queue %i didn't stop !\n", queue);
246 /* Check for pending frames */
249 pending = ath5k_hw_reg_read(ah,
250 AR5K_QUEUE_STATUS(queue)) &
251 AR5K_QCU_STS_FRMPENDCNT;
253 } while (--i && pending);
255 /* For 2413+ order PCU to drop packets using
257 if (ah->ah_mac_version >= (AR5K_SREV_AR2414 >> 4) &&
259 /* Set periodicity and duration */
260 ath5k_hw_reg_write(ah,
261 AR5K_REG_SM(100, AR5K_QUIET_CTL2_QT_PER)|
262 AR5K_REG_SM(10, AR5K_QUIET_CTL2_QT_DUR),
265 /* Enable quiet period for current TSF */
266 ath5k_hw_reg_write(ah,
267 AR5K_QUIET_CTL1_QT_EN |
268 AR5K_REG_SM(ath5k_hw_reg_read(ah,
269 AR5K_TSF_L32_5211) >> 10,
270 AR5K_QUIET_CTL1_NEXT_QT_TSF),
273 /* Force channel idle high */
274 AR5K_REG_ENABLE_BITS(ah, AR5K_DIAG_SW_5211,
275 AR5K_DIAG_SW_CHANNEL_IDLE_HIGH);
277 /* Wait a while and disable mechanism */
279 AR5K_REG_DISABLE_BITS(ah, AR5K_QUIET_CTL1,
280 AR5K_QUIET_CTL1_QT_EN);
282 /* Re-check for pending frames */
285 pending = ath5k_hw_reg_read(ah,
286 AR5K_QUEUE_STATUS(queue)) &
287 AR5K_QCU_STS_FRMPENDCNT;
289 } while (--i && pending);
291 AR5K_REG_DISABLE_BITS(ah, AR5K_DIAG_SW_5211,
292 AR5K_DIAG_SW_CHANNEL_IDLE_HIGH);
295 ATH5K_DBG(ah, ATH5K_DEBUG_DMA,
296 "quiet mechanism didn't work q:%i !\n",
301 * Disable DCU early termination
303 AR5K_REG_DISABLE_BITS(ah, AR5K_QUEUE_MISC(queue),
304 AR5K_QCU_MISC_DCU_EARLY);
307 ath5k_hw_reg_write(ah, 0, AR5K_QCU_TXD);
309 ATH5K_DBG(ah, ATH5K_DEBUG_DMA,
310 "tx dma didn't stop (q:%i, frm:%i) !\n",
316 /* TODO: Check for success on 5210 else return error */
321 * ath5k_hw_stop_beacon_queue() - Stop beacon queue
322 * @ah: The &struct ath5k_hw
323 * @queue: The queue number
325 * Returns -EIO if queue didn't stop
328 ath5k_hw_stop_beacon_queue(struct ath5k_hw *ah, unsigned int queue)
331 ret = ath5k_hw_stop_tx_dma(ah, queue);
333 ATH5K_DBG(ah, ATH5K_DEBUG_DMA,
334 "beacon queue didn't stop !\n");
341 * ath5k_hw_get_txdp() - Get TX Descriptor's address for a specific queue
342 * @ah: The &struct ath5k_hw
343 * @queue: The hw queue number
345 * Get TX descriptor's address for a specific queue. For 5210 we ignore
346 * the queue number and use tx queue type since we only have 2 queues.
347 * We use TXDP0 for normal data queue and TXDP1 for beacon queue.
348 * For newer chips with QCU/DCU we just read the corresponding TXDP register.
350 * XXX: Is TXDP read and clear ?
353 ath5k_hw_get_txdp(struct ath5k_hw *ah, unsigned int queue)
357 AR5K_ASSERT_ENTRY(queue, ah->ah_capabilities.cap_queues.q_tx_num);
360 * Get the transmit queue descriptor pointer from the selected queue
362 /*5210 doesn't have QCU*/
363 if (ah->ah_version == AR5K_AR5210) {
364 switch (ah->ah_txq[queue].tqi_type) {
365 case AR5K_TX_QUEUE_DATA:
366 tx_reg = AR5K_NOQCU_TXDP0;
368 case AR5K_TX_QUEUE_BEACON:
369 case AR5K_TX_QUEUE_CAB:
370 tx_reg = AR5K_NOQCU_TXDP1;
376 tx_reg = AR5K_QUEUE_TXDP(queue);
379 return ath5k_hw_reg_read(ah, tx_reg);
383 * ath5k_hw_set_txdp() - Set TX Descriptor's address for a specific queue
384 * @ah: The &struct ath5k_hw
385 * @queue: The hw queue number
386 * @phys_addr: The physical address
388 * Set TX descriptor's address for a specific queue. For 5210 we ignore
389 * the queue number and we use tx queue type since we only have 2 queues
390 * so as above we use TXDP0 for normal data queue and TXDP1 for beacon queue.
391 * For newer chips with QCU/DCU we just set the corresponding TXDP register.
392 * Returns -EINVAL if queue type is invalid for 5210 and -EIO if queue is still
396 ath5k_hw_set_txdp(struct ath5k_hw *ah, unsigned int queue, u32 phys_addr)
400 AR5K_ASSERT_ENTRY(queue, ah->ah_capabilities.cap_queues.q_tx_num);
403 * Set the transmit queue descriptor pointer register by type
406 if (ah->ah_version == AR5K_AR5210) {
407 switch (ah->ah_txq[queue].tqi_type) {
408 case AR5K_TX_QUEUE_DATA:
409 tx_reg = AR5K_NOQCU_TXDP0;
411 case AR5K_TX_QUEUE_BEACON:
412 case AR5K_TX_QUEUE_CAB:
413 tx_reg = AR5K_NOQCU_TXDP1;
420 * Set the transmit queue descriptor pointer for
421 * the selected queue on QCU for 5211+
422 * (this won't work if the queue is still active)
424 if (AR5K_REG_READ_Q(ah, AR5K_QCU_TXE, queue))
427 tx_reg = AR5K_QUEUE_TXDP(queue);
430 /* Set descriptor pointer */
431 ath5k_hw_reg_write(ah, phys_addr, tx_reg);
437 * ath5k_hw_update_tx_triglevel() - Update tx trigger level
438 * @ah: The &struct ath5k_hw
439 * @increase: Flag to force increase of trigger level
441 * This function increases/decreases the tx trigger level for the tx fifo
442 * buffer (aka FIFO threshold) that is used to indicate when PCU flushes
443 * the buffer and transmits its data. Lowering this results sending small
444 * frames more quickly but can lead to tx underruns, raising it a lot can
445 * result other problems. Right now we start with the lowest possible
446 * (64Bytes) and if we get tx underrun we increase it using the increase
447 * flag. Returns -EIO if we have reached maximum/minimum.
449 * XXX: Link this with tx DMA size ?
450 * XXX2: Use it to save interrupts ?
453 ath5k_hw_update_tx_triglevel(struct ath5k_hw *ah, bool increase)
455 u32 trigger_level, imr;
459 * Disable interrupts by setting the mask
461 imr = ath5k_hw_set_imr(ah, ah->ah_imr & ~AR5K_INT_GLOBAL);
463 trigger_level = AR5K_REG_MS(ath5k_hw_reg_read(ah, AR5K_TXCFG),
467 if (--trigger_level < AR5K_TUNE_MIN_TX_FIFO_THRES)
471 ((AR5K_TUNE_MAX_TX_FIFO_THRES - trigger_level) / 2);
474 * Update trigger level on success
476 if (ah->ah_version == AR5K_AR5210)
477 ath5k_hw_reg_write(ah, trigger_level, AR5K_TRIG_LVL);
479 AR5K_REG_WRITE_BITS(ah, AR5K_TXCFG,
480 AR5K_TXCFG_TXFULL, trigger_level);
486 * Restore interrupt mask
488 ath5k_hw_set_imr(ah, imr);
494 /*******************\
495 * Interrupt masking *
496 \*******************/
499 * ath5k_hw_is_intr_pending() - Check if we have pending interrupts
500 * @ah: The &struct ath5k_hw
502 * Check if we have pending interrupts to process. Returns 1 if we
503 * have pending interrupts and 0 if we haven't.
506 ath5k_hw_is_intr_pending(struct ath5k_hw *ah)
508 return ath5k_hw_reg_read(ah, AR5K_INTPEND) == 1 ? 1 : 0;
512 * ath5k_hw_get_isr() - Get interrupt status
513 * @ah: The @struct ath5k_hw
514 * @interrupt_mask: Driver's interrupt mask used to filter out
517 * This function is used inside our interrupt handler to determine the reason
518 * for the interrupt by reading Primary Interrupt Status Register. Returns an
519 * abstract interrupt status mask which is mostly ISR with some uncommon bits
520 * being mapped on some standard non hw-specific positions
521 * (check out &ath5k_int).
523 * NOTE: We do write-to-clear, so the active PISR/SISR bits at the time this
524 * function gets called are cleared on return.
527 ath5k_hw_get_isr(struct ath5k_hw *ah, enum ath5k_int *interrupt_mask)
532 * Read interrupt status from Primary Interrupt
535 * Note: PISR/SISR Not available on 5210
537 if (ah->ah_version == AR5K_AR5210) {
539 isr = ath5k_hw_reg_read(ah, AR5K_ISR);
540 if (unlikely(isr == AR5K_INT_NOCARD)) {
541 *interrupt_mask = isr;
546 * Filter out the non-common bits from the interrupt
549 *interrupt_mask = (isr & AR5K_INT_COMMON) & ah->ah_imr;
551 /* Hanlde INT_FATAL */
552 if (unlikely(isr & (AR5K_ISR_SSERR | AR5K_ISR_MCABT
554 *interrupt_mask |= AR5K_INT_FATAL;
557 * XXX: BMISS interrupts may occur after association.
558 * I found this on 5210 code but it needs testing. If this is
559 * true we should disable them before assoc and re-enable them
560 * after a successful assoc + some jiffies.
561 interrupt_mask &= ~AR5K_INT_BMISS;
574 /* Read PISR and SISRs... */
575 pisr = ath5k_hw_reg_read(ah, AR5K_PISR);
576 if (unlikely(pisr == AR5K_INT_NOCARD)) {
577 *interrupt_mask = pisr;
581 sisr0 = ath5k_hw_reg_read(ah, AR5K_SISR0);
582 sisr1 = ath5k_hw_reg_read(ah, AR5K_SISR1);
583 sisr2 = ath5k_hw_reg_read(ah, AR5K_SISR2);
584 sisr3 = ath5k_hw_reg_read(ah, AR5K_SISR3);
585 sisr4 = ath5k_hw_reg_read(ah, AR5K_SISR4);
588 * PISR holds the logical OR of interrupt bits
589 * from SISR registers:
591 * TXOK and TXDESC -> Logical OR of TXOK and TXDESC
592 * per-queue bits on SISR0
594 * TXERR and TXEOL -> Logical OR of TXERR and TXEOL
595 * per-queue bits on SISR1
597 * TXURN -> Logical OR of TXURN per-queue bits on SISR2
599 * HIUERR -> Logical OR of MCABT, SSERR and DPER bits on SISR2
601 * BCNMISC -> Logical OR of TIM, CAB_END, DTIM_SYNC
602 * BCN_TIMEOUT, CAB_TIMEOUT and DTIM
603 * (and TSFOOR ?) bits on SISR2
605 * QCBRORN and QCBRURN -> Logical OR of QCBRORN and
606 * QCBRURN per-queue bits on SISR3
607 * QTRIG -> Logical OR of QTRIG per-queue bits on SISR4
609 * If we clean these bits on PISR we 'll also clear all
610 * related bits from SISRs, e.g. if we write the TXOK bit on
611 * PISR we 'll clean all TXOK bits from SISR0 so if a new TXOK
612 * interrupt got fired for another queue while we were reading
613 * the interrupt registers and we write back the TXOK bit on
614 * PISR we 'll lose it. So make sure that we don't write back
615 * on PISR any bits that come from SISRs. Clearing them from
616 * SISRs will also clear PISR so no need to worry here.
619 /* XXX: There seems to be an issue on some cards
620 * with tx interrupt flags not being updated
621 * on PISR despite that all Tx interrupt bits
622 * are cleared on SISRs. Since we handle all
623 * Tx queues all together it shouldn't be an
624 * issue if we clear Tx interrupt flags also
625 * on PISR to avoid that.
627 pisr_clear = (pisr & ~AR5K_ISR_BITS_FROM_SISRS) |
628 (pisr & AR5K_INT_TX_ALL);
631 * Write to clear them...
632 * Note: This means that each bit we write back
633 * to the registers will get cleared, leaving the
634 * rest unaffected. So this won't affect new interrupts
635 * we didn't catch while reading/processing, we 'll get
636 * them next time get_isr gets called.
638 ath5k_hw_reg_write(ah, sisr0, AR5K_SISR0);
639 ath5k_hw_reg_write(ah, sisr1, AR5K_SISR1);
640 ath5k_hw_reg_write(ah, sisr2, AR5K_SISR2);
641 ath5k_hw_reg_write(ah, sisr3, AR5K_SISR3);
642 ath5k_hw_reg_write(ah, sisr4, AR5K_SISR4);
643 ath5k_hw_reg_write(ah, pisr_clear, AR5K_PISR);
644 /* Flush previous write */
645 ath5k_hw_reg_read(ah, AR5K_PISR);
648 * Filter out the non-common bits from the interrupt
651 *interrupt_mask = (pisr & AR5K_INT_COMMON) & ah->ah_imr;
653 ah->ah_txq_isr_txok_all = 0;
655 /* We treat TXOK,TXDESC, TXERR and TXEOL
656 * the same way (schedule the tx tasklet)
657 * so we track them all together per queue */
658 if (pisr & AR5K_ISR_TXOK)
659 ah->ah_txq_isr_txok_all |= AR5K_REG_MS(sisr0,
660 AR5K_SISR0_QCU_TXOK);
662 if (pisr & AR5K_ISR_TXDESC)
663 ah->ah_txq_isr_txok_all |= AR5K_REG_MS(sisr0,
664 AR5K_SISR0_QCU_TXDESC);
666 if (pisr & AR5K_ISR_TXERR)
667 ah->ah_txq_isr_txok_all |= AR5K_REG_MS(sisr1,
668 AR5K_SISR1_QCU_TXERR);
670 if (pisr & AR5K_ISR_TXEOL)
671 ah->ah_txq_isr_txok_all |= AR5K_REG_MS(sisr1,
672 AR5K_SISR1_QCU_TXEOL);
674 /* Misc Beacon related interrupts */
677 if (pisr & AR5K_ISR_TIM)
678 *interrupt_mask |= AR5K_INT_TIM;
681 if (pisr & AR5K_ISR_BCNMISC) {
682 if (sisr2 & AR5K_SISR2_TIM)
683 *interrupt_mask |= AR5K_INT_TIM;
684 if (sisr2 & AR5K_SISR2_DTIM)
685 *interrupt_mask |= AR5K_INT_DTIM;
686 if (sisr2 & AR5K_SISR2_DTIM_SYNC)
687 *interrupt_mask |= AR5K_INT_DTIM_SYNC;
688 if (sisr2 & AR5K_SISR2_BCN_TIMEOUT)
689 *interrupt_mask |= AR5K_INT_BCN_TIMEOUT;
690 if (sisr2 & AR5K_SISR2_CAB_TIMEOUT)
691 *interrupt_mask |= AR5K_INT_CAB_TIMEOUT;
694 /* Below interrupts are unlikely to happen */
696 /* HIU = Host Interface Unit (PCI etc)
697 * Can be one of MCABT, SSERR, DPERR from SISR2 */
698 if (unlikely(pisr & (AR5K_ISR_HIUERR)))
699 *interrupt_mask |= AR5K_INT_FATAL;
702 if (unlikely(pisr & (AR5K_ISR_BNR)))
703 *interrupt_mask |= AR5K_INT_BNR;
705 /* A queue got CBR overrun */
706 if (unlikely(pisr & (AR5K_ISR_QCBRORN)))
707 *interrupt_mask |= AR5K_INT_QCBRORN;
709 /* A queue got CBR underrun */
710 if (unlikely(pisr & (AR5K_ISR_QCBRURN)))
711 *interrupt_mask |= AR5K_INT_QCBRURN;
713 /* A queue got triggered */
714 if (unlikely(pisr & (AR5K_ISR_QTRIG)))
715 *interrupt_mask |= AR5K_INT_QTRIG;
721 * In case we didn't handle anything,
722 * print the register value.
724 if (unlikely(*interrupt_mask == 0 && net_ratelimit()))
725 ATH5K_PRINTF("ISR: 0x%08x IMR: 0x%08x\n", data, ah->ah_imr);
731 * ath5k_hw_set_imr() - Set interrupt mask
732 * @ah: The &struct ath5k_hw
733 * @new_mask: The new interrupt mask to be set
735 * Set the interrupt mask in hw to save interrupts. We do that by mapping
736 * ath5k_int bits to hw-specific bits to remove abstraction and writing
737 * Interrupt Mask Register.
740 ath5k_hw_set_imr(struct ath5k_hw *ah, enum ath5k_int new_mask)
742 enum ath5k_int old_mask, int_mask;
744 old_mask = ah->ah_imr;
747 * Disable card interrupts to prevent any race conditions
748 * (they will be re-enabled afterwards if AR5K_INT GLOBAL
749 * is set again on the new mask).
751 if (old_mask & AR5K_INT_GLOBAL) {
752 ath5k_hw_reg_write(ah, AR5K_IER_DISABLE, AR5K_IER);
753 ath5k_hw_reg_read(ah, AR5K_IER);
757 * Add additional, chipset-dependent interrupt mask flags
758 * and write them to the IMR (interrupt mask register).
760 int_mask = new_mask & AR5K_INT_COMMON;
762 if (ah->ah_version != AR5K_AR5210) {
763 /* Preserve per queue TXURN interrupt mask */
764 u32 simr2 = ath5k_hw_reg_read(ah, AR5K_SIMR2)
765 & AR5K_SIMR2_QCU_TXURN;
767 /* Fatal interrupt abstraction for 5211+ */
768 if (new_mask & AR5K_INT_FATAL) {
769 int_mask |= AR5K_IMR_HIUERR;
770 simr2 |= (AR5K_SIMR2_MCABT | AR5K_SIMR2_SSERR
774 /* Misc beacon related interrupts */
775 if (new_mask & AR5K_INT_TIM)
776 int_mask |= AR5K_IMR_TIM;
778 if (new_mask & AR5K_INT_TIM)
779 simr2 |= AR5K_SISR2_TIM;
780 if (new_mask & AR5K_INT_DTIM)
781 simr2 |= AR5K_SISR2_DTIM;
782 if (new_mask & AR5K_INT_DTIM_SYNC)
783 simr2 |= AR5K_SISR2_DTIM_SYNC;
784 if (new_mask & AR5K_INT_BCN_TIMEOUT)
785 simr2 |= AR5K_SISR2_BCN_TIMEOUT;
786 if (new_mask & AR5K_INT_CAB_TIMEOUT)
787 simr2 |= AR5K_SISR2_CAB_TIMEOUT;
790 if (new_mask & AR5K_INT_BNR)
791 int_mask |= AR5K_INT_BNR;
793 /* Note: Per queue interrupt masks
794 * are set via ath5k_hw_reset_tx_queue() (qcu.c) */
795 ath5k_hw_reg_write(ah, int_mask, AR5K_PIMR);
796 ath5k_hw_reg_write(ah, simr2, AR5K_SIMR2);
799 /* Fatal interrupt abstraction for 5210 */
800 if (new_mask & AR5K_INT_FATAL)
801 int_mask |= (AR5K_IMR_SSERR | AR5K_IMR_MCABT
802 | AR5K_IMR_HIUERR | AR5K_IMR_DPERR);
804 /* Only common interrupts left for 5210 (no SIMRs) */
805 ath5k_hw_reg_write(ah, int_mask, AR5K_IMR);
808 /* If RXNOFRM interrupt is masked disable it
809 * by setting AR5K_RXNOFRM to zero */
810 if (!(new_mask & AR5K_INT_RXNOFRM))
811 ath5k_hw_reg_write(ah, 0, AR5K_RXNOFRM);
813 /* Store new interrupt mask */
814 ah->ah_imr = new_mask;
816 /* ..re-enable interrupts if AR5K_INT_GLOBAL is set */
817 if (new_mask & AR5K_INT_GLOBAL) {
818 ath5k_hw_reg_write(ah, AR5K_IER_ENABLE, AR5K_IER);
819 ath5k_hw_reg_read(ah, AR5K_IER);
826 /********************\
828 \********************/
831 * ath5k_hw_dma_init() - Initialize DMA unit
832 * @ah: The &struct ath5k_hw
834 * Set DMA size and pre-enable interrupts
835 * (driver handles tx/rx buffer setup and
838 * XXX: Save/restore RXDP/TXDP registers ?
841 ath5k_hw_dma_init(struct ath5k_hw *ah)
844 * Set Rx/Tx DMA Configuration
846 * Set standard DMA size (128). Note that
847 * a DMA size of 512 causes rx overruns and tx errors
848 * on pci-e cards (tested on 5424 but since rx overruns
849 * also occur on 5416/5418 with madwifi we set 128
850 * for all PCI-E cards to be safe).
852 * XXX: need to check 5210 for this
853 * TODO: Check out tx trigger level, it's always 64 on dumps but I
854 * guess we can tweak it and see how it goes ;-)
856 if (ah->ah_version != AR5K_AR5210) {
857 AR5K_REG_WRITE_BITS(ah, AR5K_TXCFG,
858 AR5K_TXCFG_SDMAMR, AR5K_DMASIZE_128B);
859 AR5K_REG_WRITE_BITS(ah, AR5K_RXCFG,
860 AR5K_RXCFG_SDMAMW, AR5K_DMASIZE_128B);
863 /* Pre-enable interrupts on 5211/5212*/
864 if (ah->ah_version != AR5K_AR5210)
865 ath5k_hw_set_imr(ah, ah->ah_imr);
870 * ath5k_hw_dma_stop() - stop DMA unit
871 * @ah: The &struct ath5k_hw
873 * Stop tx/rx DMA and interrupts. Returns
874 * -EBUSY if tx or rx dma failed to stop.
876 * XXX: Sometimes DMA unit hangs and we have
877 * stuck frames on tx queues, only a reset
881 ath5k_hw_dma_stop(struct ath5k_hw *ah)
886 /* Disable interrupts */
887 ath5k_hw_set_imr(ah, 0);
890 err = ath5k_hw_stop_rx_dma(ah);
894 /* Clear any pending interrupts
895 * and disable tx dma */
896 if (ah->ah_version != AR5K_AR5210) {
897 ath5k_hw_reg_write(ah, 0xffffffff, AR5K_PISR);
898 qmax = AR5K_NUM_TX_QUEUES;
900 /* PISR/SISR Not available on 5210 */
901 ath5k_hw_reg_read(ah, AR5K_ISR);
902 qmax = AR5K_NUM_TX_QUEUES_NOQCU;
905 for (i = 0; i < qmax; i++) {
906 err = ath5k_hw_stop_tx_dma(ah, i);
907 /* -EINVAL -> queue inactive */
908 if (err && err != -EINVAL)