1 /* SPDX-License-Identifier: GPL-2.0 */
2 /* Copyright(c) 1999 - 2018 Intel Corporation. */
4 #ifndef _E1000_DEFINES_H_
5 #define _E1000_DEFINES_H_
7 /* Number of Transmit and Receive Descriptors must be a multiple of 8 */
8 #define REQ_TX_DESCRIPTOR_MULTIPLE 8
9 #define REQ_RX_DESCRIPTOR_MULTIPLE 8
11 /* Definitions for power management and wakeup registers */
13 #define E1000_WUC_APME 0x00000001 /* APM Enable */
14 #define E1000_WUC_PME_EN 0x00000002 /* PME Enable */
15 #define E1000_WUC_PME_STATUS 0x00000004 /* PME Status */
16 #define E1000_WUC_APMPME 0x00000008 /* Assert PME on APM Wakeup */
17 #define E1000_WUC_PHY_WAKE 0x00000100 /* if PHY supports wakeup */
19 /* Wake Up Filter Control */
20 #define E1000_WUFC_LNKC 0x00000001 /* Link Status Change Wakeup Enable */
21 #define E1000_WUFC_MAG 0x00000002 /* Magic Packet Wakeup Enable */
22 #define E1000_WUFC_EX 0x00000004 /* Directed Exact Wakeup Enable */
23 #define E1000_WUFC_MC 0x00000008 /* Directed Multicast Wakeup Enable */
24 #define E1000_WUFC_BC 0x00000010 /* Broadcast Wakeup Enable */
25 #define E1000_WUFC_ARP 0x00000020 /* ARP Request Packet Wakeup Enable */
28 #define E1000_WUS_LNKC E1000_WUFC_LNKC
29 #define E1000_WUS_MAG E1000_WUFC_MAG
30 #define E1000_WUS_EX E1000_WUFC_EX
31 #define E1000_WUS_MC E1000_WUFC_MC
32 #define E1000_WUS_BC E1000_WUFC_BC
34 /* Extended Device Control */
35 #define E1000_CTRL_EXT_LPCD 0x00000004 /* LCD Power Cycle Done */
36 #define E1000_CTRL_EXT_SDP3_DATA 0x00000080 /* Value of SW Definable Pin 3 */
37 #define E1000_CTRL_EXT_FORCE_SMBUS 0x00000800 /* Force SMBus mode */
38 #define E1000_CTRL_EXT_EE_RST 0x00002000 /* Reinitialize from EEPROM */
39 #define E1000_CTRL_EXT_SPD_BYPS 0x00008000 /* Speed Select Bypass */
40 #define E1000_CTRL_EXT_RO_DIS 0x00020000 /* Relaxed Ordering disable */
41 #define E1000_CTRL_EXT_DMA_DYN_CLK_EN 0x00080000 /* DMA Dynamic Clock Gating */
42 #define E1000_CTRL_EXT_LINK_MODE_MASK 0x00C00000
43 #define E1000_CTRL_EXT_LINK_MODE_PCIE_SERDES 0x00C00000
44 #define E1000_CTRL_EXT_EIAME 0x01000000
45 #define E1000_CTRL_EXT_DRV_LOAD 0x10000000 /* Driver loaded bit for FW */
46 #define E1000_CTRL_EXT_IAME 0x08000000 /* Int ACK Auto-mask */
47 #define E1000_CTRL_EXT_PBA_CLR 0x80000000 /* PBA Clear */
48 #define E1000_CTRL_EXT_LSECCK 0x00001000
49 #define E1000_CTRL_EXT_PHYPDEN 0x00100000
51 /* Receive Descriptor bit definitions */
52 #define E1000_RXD_STAT_DD 0x01 /* Descriptor Done */
53 #define E1000_RXD_STAT_EOP 0x02 /* End of Packet */
54 #define E1000_RXD_STAT_IXSM 0x04 /* Ignore checksum */
55 #define E1000_RXD_STAT_VP 0x08 /* IEEE VLAN Packet */
56 #define E1000_RXD_STAT_UDPCS 0x10 /* UDP xsum calculated */
57 #define E1000_RXD_STAT_TCPCS 0x20 /* TCP xsum calculated */
58 #define E1000_RXD_ERR_CE 0x01 /* CRC Error */
59 #define E1000_RXD_ERR_SE 0x02 /* Symbol Error */
60 #define E1000_RXD_ERR_SEQ 0x04 /* Sequence Error */
61 #define E1000_RXD_ERR_CXE 0x10 /* Carrier Extension Error */
62 #define E1000_RXD_ERR_TCPE 0x20 /* TCP/UDP Checksum Error */
63 #define E1000_RXD_ERR_IPE 0x40 /* IP Checksum Error */
64 #define E1000_RXD_ERR_RXE 0x80 /* Rx Data Error */
65 #define E1000_RXD_SPC_VLAN_MASK 0x0FFF /* VLAN ID is in lower 12 bits */
67 #define E1000_RXDEXT_STATERR_TST 0x00000100 /* Time Stamp taken */
68 #define E1000_RXDEXT_STATERR_CE 0x01000000
69 #define E1000_RXDEXT_STATERR_SE 0x02000000
70 #define E1000_RXDEXT_STATERR_SEQ 0x04000000
71 #define E1000_RXDEXT_STATERR_CXE 0x10000000
72 #define E1000_RXDEXT_STATERR_RXE 0x80000000
74 /* mask to determine if packets should be dropped due to frame errors */
75 #define E1000_RXD_ERR_FRAME_ERR_MASK ( \
82 /* Same mask, but for extended and packet split descriptors */
83 #define E1000_RXDEXT_ERR_FRAME_ERR_MASK ( \
84 E1000_RXDEXT_STATERR_CE | \
85 E1000_RXDEXT_STATERR_SE | \
86 E1000_RXDEXT_STATERR_SEQ | \
87 E1000_RXDEXT_STATERR_CXE | \
88 E1000_RXDEXT_STATERR_RXE)
90 #define E1000_MRQC_RSS_FIELD_MASK 0xFFFF0000
91 #define E1000_MRQC_RSS_FIELD_IPV4_TCP 0x00010000
92 #define E1000_MRQC_RSS_FIELD_IPV4 0x00020000
93 #define E1000_MRQC_RSS_FIELD_IPV6_TCP_EX 0x00040000
94 #define E1000_MRQC_RSS_FIELD_IPV6 0x00100000
95 #define E1000_MRQC_RSS_FIELD_IPV6_TCP 0x00200000
97 #define E1000_RXDPS_HDRSTAT_HDRSP 0x00008000
99 /* Management Control */
100 #define E1000_MANC_SMBUS_EN 0x00000001 /* SMBus Enabled - RO */
101 #define E1000_MANC_ASF_EN 0x00000002 /* ASF Enabled - RO */
102 #define E1000_MANC_ARP_EN 0x00002000 /* Enable ARP Request Filtering */
103 #define E1000_MANC_RCV_TCO_EN 0x00020000 /* Receive TCO Packets Enabled */
104 #define E1000_MANC_BLK_PHY_RST_ON_IDE 0x00040000 /* Block phy resets */
105 /* Enable MAC address filtering */
106 #define E1000_MANC_EN_MAC_ADDR_FILTER 0x00100000
107 /* Enable MNG packets to host memory */
108 #define E1000_MANC_EN_MNG2HOST 0x00200000
110 #define E1000_MANC2H_PORT_623 0x00000020 /* Port 0x26f */
111 #define E1000_MANC2H_PORT_664 0x00000040 /* Port 0x298 */
112 #define E1000_MDEF_PORT_623 0x00000800 /* Port 0x26f */
113 #define E1000_MDEF_PORT_664 0x00000400 /* Port 0x298 */
115 /* Receive Control */
116 #define E1000_RCTL_EN 0x00000002 /* enable */
117 #define E1000_RCTL_SBP 0x00000004 /* store bad packet */
118 #define E1000_RCTL_UPE 0x00000008 /* unicast promiscuous enable */
119 #define E1000_RCTL_MPE 0x00000010 /* multicast promiscuous enab */
120 #define E1000_RCTL_LPE 0x00000020 /* long packet enable */
121 #define E1000_RCTL_LBM_NO 0x00000000 /* no loopback mode */
122 #define E1000_RCTL_LBM_MAC 0x00000040 /* MAC loopback mode */
123 #define E1000_RCTL_LBM_TCVR 0x000000C0 /* tcvr loopback mode */
124 #define E1000_RCTL_DTYP_PS 0x00000400 /* Packet Split descriptor */
125 #define E1000_RCTL_RDMTS_HALF 0x00000000 /* Rx desc min threshold size */
126 #define E1000_RCTL_RDMTS_HEX 0x00010000
127 #define E1000_RCTL_MO_SHIFT 12 /* multicast offset shift */
128 #define E1000_RCTL_MO_3 0x00003000 /* multicast offset 15:4 */
129 #define E1000_RCTL_BAM 0x00008000 /* broadcast enable */
130 /* these buffer sizes are valid if E1000_RCTL_BSEX is 0 */
131 #define E1000_RCTL_SZ_2048 0x00000000 /* Rx buffer size 2048 */
132 #define E1000_RCTL_SZ_1024 0x00010000 /* Rx buffer size 1024 */
133 #define E1000_RCTL_SZ_512 0x00020000 /* Rx buffer size 512 */
134 #define E1000_RCTL_SZ_256 0x00030000 /* Rx buffer size 256 */
135 /* these buffer sizes are valid if E1000_RCTL_BSEX is 1 */
136 #define E1000_RCTL_SZ_16384 0x00010000 /* Rx buffer size 16384 */
137 #define E1000_RCTL_SZ_8192 0x00020000 /* Rx buffer size 8192 */
138 #define E1000_RCTL_SZ_4096 0x00030000 /* Rx buffer size 4096 */
139 #define E1000_RCTL_VFE 0x00040000 /* vlan filter enable */
140 #define E1000_RCTL_CFIEN 0x00080000 /* canonical form enable */
141 #define E1000_RCTL_CFI 0x00100000 /* canonical form indicator */
142 #define E1000_RCTL_DPF 0x00400000 /* Discard Pause Frames */
143 #define E1000_RCTL_PMCF 0x00800000 /* pass MAC control frames */
144 #define E1000_RCTL_BSEX 0x02000000 /* Buffer size extension */
145 #define E1000_RCTL_SECRC 0x04000000 /* Strip Ethernet CRC */
147 /* Use byte values for the following shift parameters
149 * psrctl |= (((ROUNDUP(value0, 128) >> E1000_PSRCTL_BSIZE0_SHIFT) &
150 * E1000_PSRCTL_BSIZE0_MASK) |
151 * ((ROUNDUP(value1, 1024) >> E1000_PSRCTL_BSIZE1_SHIFT) &
152 * E1000_PSRCTL_BSIZE1_MASK) |
153 * ((ROUNDUP(value2, 1024) << E1000_PSRCTL_BSIZE2_SHIFT) &
154 * E1000_PSRCTL_BSIZE2_MASK) |
155 * ((ROUNDUP(value3, 1024) << E1000_PSRCTL_BSIZE3_SHIFT) |;
156 * E1000_PSRCTL_BSIZE3_MASK))
157 * where value0 = [128..16256], default=256
158 * value1 = [1024..64512], default=4096
159 * value2 = [0..64512], default=4096
160 * value3 = [0..64512], default=0
163 #define E1000_PSRCTL_BSIZE0_MASK 0x0000007F
164 #define E1000_PSRCTL_BSIZE1_MASK 0x00003F00
165 #define E1000_PSRCTL_BSIZE2_MASK 0x003F0000
166 #define E1000_PSRCTL_BSIZE3_MASK 0x3F000000
168 #define E1000_PSRCTL_BSIZE0_SHIFT 7 /* Shift _right_ 7 */
169 #define E1000_PSRCTL_BSIZE1_SHIFT 2 /* Shift _right_ 2 */
170 #define E1000_PSRCTL_BSIZE2_SHIFT 6 /* Shift _left_ 6 */
171 #define E1000_PSRCTL_BSIZE3_SHIFT 14 /* Shift _left_ 14 */
173 /* SWFW_SYNC Definitions */
174 #define E1000_SWFW_EEP_SM 0x1
175 #define E1000_SWFW_PHY0_SM 0x2
176 #define E1000_SWFW_PHY1_SM 0x4
177 #define E1000_SWFW_CSR_SM 0x8
180 #define E1000_CTRL_FD 0x00000001 /* Full duplex.0=half; 1=full */
181 #define E1000_CTRL_GIO_MASTER_DISABLE 0x00000004 /*Blocks new Master requests */
182 #define E1000_CTRL_LRST 0x00000008 /* Link reset. 0=normal,1=reset */
183 #define E1000_CTRL_ASDE 0x00000020 /* Auto-speed detect enable */
184 #define E1000_CTRL_SLU 0x00000040 /* Set link up (Force Link) */
185 #define E1000_CTRL_ILOS 0x00000080 /* Invert Loss-Of Signal */
186 #define E1000_CTRL_SPD_SEL 0x00000300 /* Speed Select Mask */
187 #define E1000_CTRL_SPD_10 0x00000000 /* Force 10Mb */
188 #define E1000_CTRL_SPD_100 0x00000100 /* Force 100Mb */
189 #define E1000_CTRL_SPD_1000 0x00000200 /* Force 1Gb */
190 #define E1000_CTRL_FRCSPD 0x00000800 /* Force Speed */
191 #define E1000_CTRL_FRCDPX 0x00001000 /* Force Duplex */
192 #define E1000_CTRL_LANPHYPC_OVERRIDE 0x00010000 /* SW control of LANPHYPC */
193 #define E1000_CTRL_LANPHYPC_VALUE 0x00020000 /* SW value of LANPHYPC */
194 #define E1000_CTRL_MEHE 0x00080000 /* Memory Error Handling Enable */
195 #define E1000_CTRL_SWDPIN0 0x00040000 /* SWDPIN 0 value */
196 #define E1000_CTRL_SWDPIN1 0x00080000 /* SWDPIN 1 value */
197 #define E1000_CTRL_ADVD3WUC 0x00100000 /* D3 WUC */
198 #define E1000_CTRL_EN_PHY_PWR_MGMT 0x00200000 /* PHY PM enable */
199 #define E1000_CTRL_SWDPIO0 0x00400000 /* SWDPIN 0 Input or output */
200 #define E1000_CTRL_RST 0x04000000 /* Global reset */
201 #define E1000_CTRL_RFCE 0x08000000 /* Receive Flow Control enable */
202 #define E1000_CTRL_TFCE 0x10000000 /* Transmit flow control enable */
203 #define E1000_CTRL_VME 0x40000000 /* IEEE VLAN mode enable */
204 #define E1000_CTRL_PHY_RST 0x80000000 /* PHY Reset */
206 #define E1000_PCS_LCTL_FORCE_FCTRL 0x80
208 #define E1000_PCS_LSTS_AN_COMPLETE 0x10000
211 #define E1000_STATUS_FD 0x00000001 /* Full duplex.0=half,1=full */
212 #define E1000_STATUS_LU 0x00000002 /* Link up.0=no,1=link */
213 #define E1000_STATUS_FUNC_MASK 0x0000000C /* PCI Function Mask */
214 #define E1000_STATUS_FUNC_SHIFT 2
215 #define E1000_STATUS_FUNC_1 0x00000004 /* Function 1 */
216 #define E1000_STATUS_TXOFF 0x00000010 /* transmission paused */
217 #define E1000_STATUS_SPEED_MASK 0x000000C0
218 #define E1000_STATUS_SPEED_10 0x00000000 /* Speed 10Mb/s */
219 #define E1000_STATUS_SPEED_100 0x00000040 /* Speed 100Mb/s */
220 #define E1000_STATUS_SPEED_1000 0x00000080 /* Speed 1000Mb/s */
221 #define E1000_STATUS_LAN_INIT_DONE 0x00000200 /* Lan Init Completion by NVM */
222 #define E1000_STATUS_PHYRA 0x00000400 /* PHY Reset Asserted */
223 #define E1000_STATUS_GIO_MASTER_ENABLE 0x00080000 /* Master Req status */
225 #define HALF_DUPLEX 1
226 #define FULL_DUPLEX 2
228 #define ADVERTISE_10_HALF 0x0001
229 #define ADVERTISE_10_FULL 0x0002
230 #define ADVERTISE_100_HALF 0x0004
231 #define ADVERTISE_100_FULL 0x0008
232 #define ADVERTISE_1000_HALF 0x0010 /* Not used, just FYI */
233 #define ADVERTISE_1000_FULL 0x0020
235 /* 1000/H is not supported, nor spec-compliant. */
236 #define E1000_ALL_SPEED_DUPLEX ( \
237 ADVERTISE_10_HALF | ADVERTISE_10_FULL | ADVERTISE_100_HALF | \
238 ADVERTISE_100_FULL | ADVERTISE_1000_FULL)
239 #define E1000_ALL_NOT_GIG ( \
240 ADVERTISE_10_HALF | ADVERTISE_10_FULL | ADVERTISE_100_HALF | \
242 #define E1000_ALL_100_SPEED (ADVERTISE_100_HALF | ADVERTISE_100_FULL)
243 #define E1000_ALL_10_SPEED (ADVERTISE_10_HALF | ADVERTISE_10_FULL)
244 #define E1000_ALL_HALF_DUPLEX (ADVERTISE_10_HALF | ADVERTISE_100_HALF)
246 #define AUTONEG_ADVERTISE_SPEED_DEFAULT E1000_ALL_SPEED_DUPLEX
249 #define E1000_PHY_LED0_MODE_MASK 0x00000007
250 #define E1000_PHY_LED0_IVRT 0x00000008
251 #define E1000_PHY_LED0_MASK 0x0000001F
253 #define E1000_LEDCTL_LED0_MODE_MASK 0x0000000F
254 #define E1000_LEDCTL_LED0_MODE_SHIFT 0
255 #define E1000_LEDCTL_LED0_IVRT 0x00000040
256 #define E1000_LEDCTL_LED0_BLINK 0x00000080
258 #define E1000_LEDCTL_MODE_LINK_UP 0x2
259 #define E1000_LEDCTL_MODE_LED_ON 0xE
260 #define E1000_LEDCTL_MODE_LED_OFF 0xF
262 /* Transmit Descriptor bit definitions */
263 #define E1000_TXD_DTYP_D 0x00100000 /* Data Descriptor */
264 #define E1000_TXD_POPTS_IXSM 0x01 /* Insert IP checksum */
265 #define E1000_TXD_POPTS_TXSM 0x02 /* Insert TCP/UDP checksum */
266 #define E1000_TXD_CMD_EOP 0x01000000 /* End of Packet */
267 #define E1000_TXD_CMD_IFCS 0x02000000 /* Insert FCS (Ethernet CRC) */
268 #define E1000_TXD_CMD_IC 0x04000000 /* Insert Checksum */
269 #define E1000_TXD_CMD_RS 0x08000000 /* Report Status */
270 #define E1000_TXD_CMD_RPS 0x10000000 /* Report Packet Sent */
271 #define E1000_TXD_CMD_DEXT 0x20000000 /* Descriptor extension (0 = legacy) */
272 #define E1000_TXD_CMD_VLE 0x40000000 /* Add VLAN tag */
273 #define E1000_TXD_CMD_IDE 0x80000000 /* Enable Tidv register */
274 #define E1000_TXD_STAT_DD 0x00000001 /* Descriptor Done */
275 #define E1000_TXD_STAT_EC 0x00000002 /* Excess Collisions */
276 #define E1000_TXD_STAT_LC 0x00000004 /* Late Collisions */
277 #define E1000_TXD_STAT_TU 0x00000008 /* Transmit underrun */
278 #define E1000_TXD_CMD_TCP 0x01000000 /* TCP packet */
279 #define E1000_TXD_CMD_IP 0x02000000 /* IP packet */
280 #define E1000_TXD_CMD_TSE 0x04000000 /* TCP Seg enable */
281 #define E1000_TXD_STAT_TC 0x00000004 /* Tx Underrun */
282 #define E1000_TXD_EXTCMD_TSTAMP 0x00000010 /* IEEE1588 Timestamp packet */
284 /* Transmit Control */
285 #define E1000_TCTL_EN 0x00000002 /* enable Tx */
286 #define E1000_TCTL_PSP 0x00000008 /* pad short packets */
287 #define E1000_TCTL_CT 0x00000ff0 /* collision threshold */
288 #define E1000_TCTL_COLD 0x003ff000 /* collision distance */
289 #define E1000_TCTL_RTLC 0x01000000 /* Re-transmit on late collision */
290 #define E1000_TCTL_MULR 0x10000000 /* Multiple request support */
293 #define E1000_SCTL_DISABLE_SERDES_LOOPBACK 0x0400
294 #define E1000_SCTL_ENABLE_SERDES_LOOPBACK 0x0410
296 /* Receive Checksum Control */
297 #define E1000_RXCSUM_TUOFL 0x00000200 /* TCP / UDP checksum offload */
298 #define E1000_RXCSUM_IPPCSE 0x00001000 /* IP payload checksum enable */
299 #define E1000_RXCSUM_PCSD 0x00002000 /* packet checksum disabled */
301 /* Header split receive */
302 #define E1000_RFCTL_NFSW_DIS 0x00000040
303 #define E1000_RFCTL_NFSR_DIS 0x00000080
304 #define E1000_RFCTL_ACK_DIS 0x00001000
305 #define E1000_RFCTL_EXTEN 0x00008000
306 #define E1000_RFCTL_IPV6_EX_DIS 0x00010000
307 #define E1000_RFCTL_NEW_IPV6_EXT_DIS 0x00020000
309 /* Collision related configuration parameters */
310 #define E1000_COLLISION_THRESHOLD 15
311 #define E1000_CT_SHIFT 4
312 #define E1000_COLLISION_DISTANCE 63
313 #define E1000_COLD_SHIFT 12
315 /* Default values for the transmit IPG register */
316 #define DEFAULT_82543_TIPG_IPGT_COPPER 8
318 #define E1000_TIPG_IPGT_MASK 0x000003FF
320 #define DEFAULT_82543_TIPG_IPGR1 8
321 #define E1000_TIPG_IPGR1_SHIFT 10
323 #define DEFAULT_82543_TIPG_IPGR2 6
324 #define DEFAULT_80003ES2LAN_TIPG_IPGR2 7
325 #define E1000_TIPG_IPGR2_SHIFT 20
327 #define MAX_JUMBO_FRAME_SIZE 0x3F00
328 #define E1000_TX_PTR_GAP 0x1F
330 /* Extended Configuration Control and Size */
331 #define E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP 0x00000020
332 #define E1000_EXTCNF_CTRL_LCD_WRITE_ENABLE 0x00000001
333 #define E1000_EXTCNF_CTRL_OEM_WRITE_ENABLE 0x00000008
334 #define E1000_EXTCNF_CTRL_SWFLAG 0x00000020
335 #define E1000_EXTCNF_CTRL_GATE_PHY_CFG 0x00000080
336 #define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_MASK 0x00FF0000
337 #define E1000_EXTCNF_SIZE_EXT_PCIE_LENGTH_SHIFT 16
338 #define E1000_EXTCNF_CTRL_EXT_CNF_POINTER_MASK 0x0FFF0000
339 #define E1000_EXTCNF_CTRL_EXT_CNF_POINTER_SHIFT 16
341 #define E1000_PHY_CTRL_D0A_LPLU 0x00000002
342 #define E1000_PHY_CTRL_NOND0A_LPLU 0x00000004
343 #define E1000_PHY_CTRL_NOND0A_GBE_DISABLE 0x00000008
344 #define E1000_PHY_CTRL_GBE_DISABLE 0x00000040
346 #define E1000_KABGTXD_BGSQLBIAS 0x00050000
348 /* Low Power IDLE Control */
349 #define E1000_LPIC_LPIET_SHIFT 24 /* Low Power Idle Entry Time */
352 #define E1000_PBA_8K 0x0008 /* 8KB */
353 #define E1000_PBA_16K 0x0010 /* 16KB */
355 #define E1000_PBA_RXA_MASK 0xFFFF
357 #define E1000_PBS_16K E1000_PBA_16K
359 /* Uncorrectable/correctable ECC Error counts and enable bits */
360 #define E1000_PBECCSTS_CORR_ERR_CNT_MASK 0x000000FF
361 #define E1000_PBECCSTS_UNCORR_ERR_CNT_MASK 0x0000FF00
362 #define E1000_PBECCSTS_UNCORR_ERR_CNT_SHIFT 8
363 #define E1000_PBECCSTS_ECC_ENABLE 0x00010000
369 #define MIN_NUM_XMITS 1000
371 /* SW Semaphore Register */
372 #define E1000_SWSM_SMBI 0x00000001 /* Driver Semaphore bit */
373 #define E1000_SWSM_SWESMBI 0x00000002 /* FW Semaphore bit */
374 #define E1000_SWSM_DRV_LOAD 0x00000008 /* Driver Loaded Bit */
376 #define E1000_SWSM2_LOCK 0x00000002 /* Secondary driver semaphore bit */
378 /* Interrupt Cause Read */
379 #define E1000_ICR_TXDW 0x00000001 /* Transmit desc written back */
380 #define E1000_ICR_LSC 0x00000004 /* Link Status Change */
381 #define E1000_ICR_RXSEQ 0x00000008 /* Rx sequence error */
382 #define E1000_ICR_RXDMT0 0x00000010 /* Rx desc min. threshold (0) */
383 #define E1000_ICR_RXO 0x00000040 /* Receiver Overrun */
384 #define E1000_ICR_RXT0 0x00000080 /* Rx timer intr (ring 0) */
385 #define E1000_ICR_MDAC 0x00000200 /* MDIO Access Complete */
386 #define E1000_ICR_SRPD 0x00010000 /* Small Receive Packet Detected */
387 #define E1000_ICR_ACK 0x00020000 /* Receive ACK Frame Detected */
388 #define E1000_ICR_MNG 0x00040000 /* Manageability Event Detected */
389 #define E1000_ICR_ECCER 0x00400000 /* Uncorrectable ECC Error */
390 /* If this bit asserted, the driver should claim the interrupt */
391 #define E1000_ICR_INT_ASSERTED 0x80000000
392 #define E1000_ICR_RXQ0 0x00100000 /* Rx Queue 0 Interrupt */
393 #define E1000_ICR_RXQ1 0x00200000 /* Rx Queue 1 Interrupt */
394 #define E1000_ICR_TXQ0 0x00400000 /* Tx Queue 0 Interrupt */
395 #define E1000_ICR_TXQ1 0x00800000 /* Tx Queue 1 Interrupt */
396 #define E1000_ICR_OTHER 0x01000000 /* Other Interrupt */
398 /* PBA ECC Register */
399 #define E1000_PBA_ECC_COUNTER_MASK 0xFFF00000 /* ECC counter mask */
400 #define E1000_PBA_ECC_COUNTER_SHIFT 20 /* ECC counter shift value */
401 #define E1000_PBA_ECC_CORR_EN 0x00000001 /* ECC correction enable */
402 #define E1000_PBA_ECC_STAT_CLR 0x00000002 /* Clear ECC error counter */
403 #define E1000_PBA_ECC_INT_EN 0x00000004 /* Enable ICR bit 5 for ECC */
405 /* This defines the bits that are set in the Interrupt Mask
406 * Set/Read Register. Each bit is documented below:
407 * o RXT0 = Receiver Timer Interrupt (ring 0)
408 * o TXDW = Transmit Descriptor Written Back
409 * o RXDMT0 = Receive Descriptor Minimum Threshold hit (ring 0)
410 * o RXSEQ = Receive Sequence Error
411 * o LSC = Link Status Change
413 #define IMS_ENABLE_MASK ( \
420 /* These are all of the events related to the OTHER interrupt.
422 #define IMS_OTHER_MASK ( \
430 /* Interrupt Mask Set */
431 #define E1000_IMS_TXDW E1000_ICR_TXDW /* Transmit desc written back */
432 #define E1000_IMS_LSC E1000_ICR_LSC /* Link Status Change */
433 #define E1000_IMS_RXSEQ E1000_ICR_RXSEQ /* Rx sequence error */
434 #define E1000_IMS_RXDMT0 E1000_ICR_RXDMT0 /* Rx desc min. threshold */
435 #define E1000_IMS_RXO E1000_ICR_RXO /* Receiver Overrun */
436 #define E1000_IMS_RXT0 E1000_ICR_RXT0 /* Rx timer intr */
437 #define E1000_IMS_MDAC E1000_ICR_MDAC /* MDIO Access Complete */
438 #define E1000_IMS_SRPD E1000_ICR_SRPD /* Small Receive Packet */
439 #define E1000_IMS_ACK E1000_ICR_ACK /* Receive ACK Frame Detected */
440 #define E1000_IMS_MNG E1000_ICR_MNG /* Manageability Event */
441 #define E1000_IMS_ECCER E1000_ICR_ECCER /* Uncorrectable ECC Error */
442 #define E1000_IMS_RXQ0 E1000_ICR_RXQ0 /* Rx Queue 0 Interrupt */
443 #define E1000_IMS_RXQ1 E1000_ICR_RXQ1 /* Rx Queue 1 Interrupt */
444 #define E1000_IMS_TXQ0 E1000_ICR_TXQ0 /* Tx Queue 0 Interrupt */
445 #define E1000_IMS_TXQ1 E1000_ICR_TXQ1 /* Tx Queue 1 Interrupt */
446 #define E1000_IMS_OTHER E1000_ICR_OTHER /* Other Interrupt */
448 /* Interrupt Cause Set */
449 #define E1000_ICS_LSC E1000_ICR_LSC /* Link Status Change */
450 #define E1000_ICS_RXSEQ E1000_ICR_RXSEQ /* Rx sequence error */
451 #define E1000_ICS_RXDMT0 E1000_ICR_RXDMT0 /* Rx desc min. threshold */
452 #define E1000_ICS_OTHER E1000_ICR_OTHER /* Other Interrupt */
454 /* Transmit Descriptor Control */
455 #define E1000_TXDCTL_PTHRESH 0x0000003F /* TXDCTL Prefetch Threshold */
456 #define E1000_TXDCTL_HTHRESH 0x00003F00 /* TXDCTL Host Threshold */
457 #define E1000_TXDCTL_WTHRESH 0x003F0000 /* TXDCTL Writeback Threshold */
458 #define E1000_TXDCTL_GRAN 0x01000000 /* TXDCTL Granularity */
459 #define E1000_TXDCTL_FULL_TX_DESC_WB 0x01010000 /* GRAN=1, WTHRESH=1 */
460 #define E1000_TXDCTL_MAX_TX_DESC_PREFETCH 0x0100001F /* GRAN=1, PTHRESH=31 */
461 /* Enable the counting of desc. still to be processed. */
462 #define E1000_TXDCTL_COUNT_DESC 0x00400000
464 /* Flow Control Constants */
465 #define FLOW_CONTROL_ADDRESS_LOW 0x00C28001
466 #define FLOW_CONTROL_ADDRESS_HIGH 0x00000100
467 #define FLOW_CONTROL_TYPE 0x8808
469 /* 802.1q VLAN Packet Size */
470 #define E1000_VLAN_FILTER_TBL_SIZE 128 /* VLAN Filter Table (4096 bits) */
473 * Number of high/low register pairs in the RAR. The RAR (Receive Address
474 * Registers) holds the directed and multicast addresses that we monitor.
475 * Technically, we have 16 spots. However, we reserve one of these spots
476 * (RAR[15]) for our directed address used by controllers with
477 * manageability enabled, allowing us room for 15 multicast addresses.
479 #define E1000_RAR_ENTRIES 15
480 #define E1000_RAH_AV 0x80000000 /* Receive descriptor valid */
481 #define E1000_RAL_MAC_ADDR_LEN 4
482 #define E1000_RAH_MAC_ADDR_LEN 2
485 #define E1000_ERR_NVM 1
486 #define E1000_ERR_PHY 2
487 #define E1000_ERR_CONFIG 3
488 #define E1000_ERR_PARAM 4
489 #define E1000_ERR_MAC_INIT 5
490 #define E1000_ERR_PHY_TYPE 6
491 #define E1000_ERR_RESET 9
492 #define E1000_ERR_MASTER_REQUESTS_PENDING 10
493 #define E1000_ERR_HOST_INTERFACE_COMMAND 11
494 #define E1000_BLK_PHY_RESET 12
495 #define E1000_ERR_SWFW_SYNC 13
496 #define E1000_NOT_IMPLEMENTED 14
497 #define E1000_ERR_INVALID_ARGUMENT 16
498 #define E1000_ERR_NO_SPACE 17
499 #define E1000_ERR_NVM_PBA_SECTION 18
501 /* Loop limit on how long we wait for auto-negotiation to complete */
502 #define FIBER_LINK_UP_LIMIT 50
503 #define COPPER_LINK_UP_LIMIT 10
504 #define PHY_AUTO_NEG_LIMIT 45
505 #define PHY_FORCE_LIMIT 20
506 /* Number of 100 microseconds we wait for PCI Express master disable */
507 #define MASTER_DISABLE_TIMEOUT 800
508 /* Number of milliseconds we wait for PHY configuration done after MAC reset */
509 #define PHY_CFG_TIMEOUT 100
510 /* Number of 2 milliseconds we wait for acquiring MDIO ownership. */
511 #define MDIO_OWNERSHIP_TIMEOUT 10
512 /* Number of milliseconds for NVM auto read done after MAC reset. */
513 #define AUTO_READ_DONE_TIMEOUT 10
516 #define E1000_FCRTH_RTH 0x0000FFF8 /* Mask Bits[15:3] for RTH */
517 #define E1000_FCRTL_RTL 0x0000FFF8 /* Mask Bits[15:3] for RTL */
518 #define E1000_FCRTL_XONE 0x80000000 /* Enable XON frame transmission */
520 /* Transmit Configuration Word */
521 #define E1000_TXCW_FD 0x00000020 /* TXCW full duplex */
522 #define E1000_TXCW_PAUSE 0x00000080 /* TXCW sym pause request */
523 #define E1000_TXCW_ASM_DIR 0x00000100 /* TXCW astm pause direction */
524 #define E1000_TXCW_PAUSE_MASK 0x00000180 /* TXCW pause request mask */
525 #define E1000_TXCW_ANE 0x80000000 /* Auto-neg enable */
527 /* Receive Configuration Word */
528 #define E1000_RXCW_CW 0x0000ffff /* RxConfigWord mask */
529 #define E1000_RXCW_IV 0x08000000 /* Receive config invalid */
530 #define E1000_RXCW_C 0x20000000 /* Receive config */
531 #define E1000_RXCW_SYNCH 0x40000000 /* Receive config synch */
534 #define E1000_TSYNCTXCTL_MAX_ALLOWED_DLY_MASK 0x0000F000 /* max delay */
535 #define E1000_TSYNCTXCTL_SYNC_COMP 0x40000000 /* sync complete */
536 #define E1000_TSYNCTXCTL_START_SYNC 0x80000000 /* initiate sync */
538 #define E1000_TSYNCTXCTL_VALID 0x00000001 /* Tx timestamp valid */
539 #define E1000_TSYNCTXCTL_ENABLED 0x00000010 /* enable Tx timestamping */
541 #define E1000_TSYNCRXCTL_VALID 0x00000001 /* Rx timestamp valid */
542 #define E1000_TSYNCRXCTL_TYPE_MASK 0x0000000E /* Rx type mask */
543 #define E1000_TSYNCRXCTL_TYPE_L2_V2 0x00
544 #define E1000_TSYNCRXCTL_TYPE_L4_V1 0x02
545 #define E1000_TSYNCRXCTL_TYPE_L2_L4_V2 0x04
546 #define E1000_TSYNCRXCTL_TYPE_ALL 0x08
547 #define E1000_TSYNCRXCTL_TYPE_EVENT_V2 0x0A
548 #define E1000_TSYNCRXCTL_ENABLED 0x00000010 /* enable Rx timestamping */
549 #define E1000_TSYNCRXCTL_SYSCFI 0x00000020 /* Sys clock frequency */
551 #define E1000_RXMTRL_PTP_V1_SYNC_MESSAGE 0x00000000
552 #define E1000_RXMTRL_PTP_V1_DELAY_REQ_MESSAGE 0x00010000
554 #define E1000_RXMTRL_PTP_V2_SYNC_MESSAGE 0x00000000
555 #define E1000_RXMTRL_PTP_V2_DELAY_REQ_MESSAGE 0x01000000
557 #define E1000_TIMINCA_INCPERIOD_SHIFT 24
558 #define E1000_TIMINCA_INCVALUE_MASK 0x00FFFFFF
560 /* PCI Express Control */
561 #define E1000_GCR_RXD_NO_SNOOP 0x00000001
562 #define E1000_GCR_RXDSCW_NO_SNOOP 0x00000002
563 #define E1000_GCR_RXDSCR_NO_SNOOP 0x00000004
564 #define E1000_GCR_TXD_NO_SNOOP 0x00000008
565 #define E1000_GCR_TXDSCW_NO_SNOOP 0x00000010
566 #define E1000_GCR_TXDSCR_NO_SNOOP 0x00000020
568 #define PCIE_NO_SNOOP_ALL (E1000_GCR_RXD_NO_SNOOP | \
569 E1000_GCR_RXDSCW_NO_SNOOP | \
570 E1000_GCR_RXDSCR_NO_SNOOP | \
571 E1000_GCR_TXD_NO_SNOOP | \
572 E1000_GCR_TXDSCW_NO_SNOOP | \
573 E1000_GCR_TXDSCR_NO_SNOOP)
576 #define E1000_EECD_SK 0x00000001 /* NVM Clock */
577 #define E1000_EECD_CS 0x00000002 /* NVM Chip Select */
578 #define E1000_EECD_DI 0x00000004 /* NVM Data In */
579 #define E1000_EECD_DO 0x00000008 /* NVM Data Out */
580 #define E1000_EECD_REQ 0x00000040 /* NVM Access Request */
581 #define E1000_EECD_GNT 0x00000080 /* NVM Access Grant */
582 #define E1000_EECD_PRES 0x00000100 /* NVM Present */
583 #define E1000_EECD_SIZE 0x00000200 /* NVM Size (0=64 word 1=256 word) */
584 /* NVM Addressing bits based on type (0-small, 1-large) */
585 #define E1000_EECD_ADDR_BITS 0x00000400
586 #define E1000_NVM_GRANT_ATTEMPTS 1000 /* NVM # attempts to gain grant */
587 #define E1000_EECD_AUTO_RD 0x00000200 /* NVM Auto Read done */
588 #define E1000_EECD_SIZE_EX_MASK 0x00007800 /* NVM Size */
589 #define E1000_EECD_SIZE_EX_SHIFT 11
590 #define E1000_EECD_FLUPD 0x00080000 /* Update FLASH */
591 #define E1000_EECD_AUPDEN 0x00100000 /* Enable Autonomous FLASH update */
592 #define E1000_EECD_SEC1VAL 0x00400000 /* Sector One Valid */
593 #define E1000_EECD_SEC1VAL_VALID_MASK (E1000_EECD_AUTO_RD | E1000_EECD_PRES)
595 #define E1000_NVM_RW_REG_DATA 16 /* Offset to data in NVM r/w regs */
596 #define E1000_NVM_RW_REG_DONE 2 /* Offset to READ/WRITE done bit */
597 #define E1000_NVM_RW_REG_START 1 /* Start operation */
598 #define E1000_NVM_RW_ADDR_SHIFT 2 /* Shift to the address bits */
599 #define E1000_NVM_POLL_WRITE 1 /* Flag for polling write complete */
600 #define E1000_NVM_POLL_READ 0 /* Flag for polling read complete */
601 #define E1000_FLASH_UPDATES 2000
603 /* NVM Word Offsets */
604 #define NVM_COMPAT 0x0003
605 #define NVM_ID_LED_SETTINGS 0x0004
606 #define NVM_FUTURE_INIT_WORD1 0x0019
607 #define NVM_COMPAT_VALID_CSUM 0x0001
608 #define NVM_FUTURE_INIT_WORD1_VALID_CSUM 0x0040
610 #define NVM_INIT_CONTROL2_REG 0x000F
611 #define NVM_INIT_CONTROL3_PORT_B 0x0014
612 #define NVM_INIT_3GIO_3 0x001A
613 #define NVM_INIT_CONTROL3_PORT_A 0x0024
614 #define NVM_CFG 0x0012
615 #define NVM_ALT_MAC_ADDR_PTR 0x0037
616 #define NVM_CHECKSUM_REG 0x003F
618 #define E1000_NVM_CFG_DONE_PORT_0 0x40000 /* MNG config cycle done */
619 #define E1000_NVM_CFG_DONE_PORT_1 0x80000 /* ...for second port */
621 /* Mask bits for fields in Word 0x0f of the NVM */
622 #define NVM_WORD0F_PAUSE_MASK 0x3000
623 #define NVM_WORD0F_PAUSE 0x1000
624 #define NVM_WORD0F_ASM_DIR 0x2000
626 /* Mask bits for fields in Word 0x1a of the NVM */
627 #define NVM_WORD1A_ASPM_MASK 0x000C
629 /* Mask bits for fields in Word 0x03 of the EEPROM */
630 #define NVM_COMPAT_LOM 0x0800
632 /* length of string needed to store PBA number */
633 #define E1000_PBANUM_LENGTH 11
635 /* For checksumming, the sum of all words in the NVM should equal 0xBABA. */
636 #define NVM_SUM 0xBABA
638 /* PBA (printed board assembly) number words */
639 #define NVM_PBA_OFFSET_0 8
640 #define NVM_PBA_OFFSET_1 9
641 #define NVM_PBA_PTR_GUARD 0xFAFA
642 #define NVM_WORD_SIZE_BASE_SHIFT 6
644 /* NVM Commands - SPI */
645 #define NVM_MAX_RETRY_SPI 5000 /* Max wait of 5ms, for RDY signal */
646 #define NVM_READ_OPCODE_SPI 0x03 /* NVM read opcode */
647 #define NVM_WRITE_OPCODE_SPI 0x02 /* NVM write opcode */
648 #define NVM_A8_OPCODE_SPI 0x08 /* opcode bit-3 = address bit-8 */
649 #define NVM_WREN_OPCODE_SPI 0x06 /* NVM set Write Enable latch */
650 #define NVM_RDSR_OPCODE_SPI 0x05 /* NVM read Status register */
652 /* SPI NVM Status Register */
653 #define NVM_STATUS_RDY_SPI 0x01
655 /* Word definitions for ID LED Settings */
656 #define ID_LED_RESERVED_0000 0x0000
657 #define ID_LED_RESERVED_FFFF 0xFFFF
658 #define ID_LED_DEFAULT ((ID_LED_OFF1_ON2 << 12) | \
659 (ID_LED_OFF1_OFF2 << 8) | \
660 (ID_LED_DEF1_DEF2 << 4) | \
662 #define ID_LED_DEF1_DEF2 0x1
663 #define ID_LED_DEF1_ON2 0x2
664 #define ID_LED_DEF1_OFF2 0x3
665 #define ID_LED_ON1_DEF2 0x4
666 #define ID_LED_ON1_ON2 0x5
667 #define ID_LED_ON1_OFF2 0x6
668 #define ID_LED_OFF1_DEF2 0x7
669 #define ID_LED_OFF1_ON2 0x8
670 #define ID_LED_OFF1_OFF2 0x9
672 #define IGP_ACTIVITY_LED_MASK 0xFFFFF0FF
673 #define IGP_ACTIVITY_LED_ENABLE 0x0300
674 #define IGP_LED3_MODE 0x07000000
676 /* PCI/PCI-X/PCI-EX Config space */
677 #define PCI_HEADER_TYPE_REGISTER 0x0E
678 #define PCIE_LINK_STATUS 0x12
680 #define PCI_HEADER_TYPE_MULTIFUNC 0x80
681 #define PCIE_LINK_WIDTH_MASK 0x3F0
682 #define PCIE_LINK_WIDTH_SHIFT 4
684 #define PHY_REVISION_MASK 0xFFFFFFF0
685 #define MAX_PHY_REG_ADDRESS 0x1F /* 5 bit address bus (0-0x1F) */
686 #define MAX_PHY_MULTI_PAGE_REG 0xF
688 /* Bit definitions for valid PHY IDs.
692 #define M88E1000_E_PHY_ID 0x01410C50
693 #define M88E1000_I_PHY_ID 0x01410C30
694 #define M88E1011_I_PHY_ID 0x01410C20
695 #define IGP01E1000_I_PHY_ID 0x02A80380
696 #define M88E1111_I_PHY_ID 0x01410CC0
697 #define GG82563_E_PHY_ID 0x01410CA0
698 #define IGP03E1000_E_PHY_ID 0x02A80390
699 #define IFE_E_PHY_ID 0x02A80330
700 #define IFE_PLUS_E_PHY_ID 0x02A80320
701 #define IFE_C_E_PHY_ID 0x02A80310
702 #define BME1000_E_PHY_ID 0x01410CB0
703 #define BME1000_E_PHY_ID_R2 0x01410CB1
704 #define I82577_E_PHY_ID 0x01540050
705 #define I82578_E_PHY_ID 0x004DD040
706 #define I82579_E_PHY_ID 0x01540090
707 #define I217_E_PHY_ID 0x015400A0
709 /* M88E1000 Specific Registers */
710 #define M88E1000_PHY_SPEC_CTRL 0x10 /* PHY Specific Control Register */
711 #define M88E1000_PHY_SPEC_STATUS 0x11 /* PHY Specific Status Register */
712 #define M88E1000_EXT_PHY_SPEC_CTRL 0x14 /* Extended PHY Specific Control */
714 #define M88E1000_PHY_PAGE_SELECT 0x1D /* Reg 29 for page number setting */
715 #define M88E1000_PHY_GEN_CONTROL 0x1E /* Its meaning depends on reg 29 */
717 /* M88E1000 PHY Specific Control Register */
718 #define M88E1000_PSCR_POLARITY_REVERSAL 0x0002 /* 1=Polarity Reversal enabled */
719 #define M88E1000_PSCR_MDI_MANUAL_MODE 0x0000 /* MDI Crossover Mode bits 6:5 */
720 /* Manual MDI configuration */
721 #define M88E1000_PSCR_MDIX_MANUAL_MODE 0x0020 /* Manual MDIX configuration */
722 /* 1000BASE-T: Auto crossover, 100BASE-TX/10BASE-T: MDI Mode */
723 #define M88E1000_PSCR_AUTO_X_1000T 0x0040
724 /* Auto crossover enabled all speeds */
725 #define M88E1000_PSCR_AUTO_X_MODE 0x0060
726 #define M88E1000_PSCR_ASSERT_CRS_ON_TX 0x0800 /* 1=Assert CRS on Transmit */
728 /* M88E1000 PHY Specific Status Register */
729 #define M88E1000_PSSR_REV_POLARITY 0x0002 /* 1=Polarity reversed */
730 #define M88E1000_PSSR_DOWNSHIFT 0x0020 /* 1=Downshifted */
731 #define M88E1000_PSSR_MDIX 0x0040 /* 1=MDIX; 0=MDI */
732 /* 0=<50M; 1=50-80M; 2=80-110M; 3=110-140M; 4=>140M */
733 #define M88E1000_PSSR_CABLE_LENGTH 0x0380
734 #define M88E1000_PSSR_SPEED 0xC000 /* Speed, bits 14:15 */
735 #define M88E1000_PSSR_1000MBS 0x8000 /* 10=1000Mbs */
737 #define M88E1000_PSSR_CABLE_LENGTH_SHIFT 7
739 /* Number of times we will attempt to autonegotiate before downshifting if we
742 #define M88E1000_EPSCR_MASTER_DOWNSHIFT_MASK 0x0C00
743 #define M88E1000_EPSCR_MASTER_DOWNSHIFT_1X 0x0000
744 /* Number of times we will attempt to autonegotiate before downshifting if we
747 #define M88E1000_EPSCR_SLAVE_DOWNSHIFT_MASK 0x0300
748 #define M88E1000_EPSCR_SLAVE_DOWNSHIFT_1X 0x0100
749 #define M88E1000_EPSCR_TX_CLK_25 0x0070 /* 25 MHz TX_CLK */
751 /* M88EC018 Rev 2 specific DownShift settings */
752 #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_MASK 0x0E00
753 #define M88EC018_EPSCR_DOWNSHIFT_COUNTER_5X 0x0800
755 #define I82578_EPSCR_DOWNSHIFT_ENABLE 0x0020
756 #define I82578_EPSCR_DOWNSHIFT_COUNTER_MASK 0x001C
758 /* BME1000 PHY Specific Control Register */
759 #define BME1000_PSCR_ENABLE_DOWNSHIFT 0x0800 /* 1 = enable downshift */
763 * 4-0: register offset
765 #define GG82563_PAGE_SHIFT 5
766 #define GG82563_REG(page, reg) \
767 (((page) << GG82563_PAGE_SHIFT) | ((reg) & MAX_PHY_REG_ADDRESS))
768 #define GG82563_MIN_ALT_REG 30
770 /* GG82563 Specific Registers */
771 #define GG82563_PHY_SPEC_CTRL \
772 GG82563_REG(0, 16) /* PHY Specific Control */
773 #define GG82563_PHY_PAGE_SELECT \
774 GG82563_REG(0, 22) /* Page Select */
775 #define GG82563_PHY_SPEC_CTRL_2 \
776 GG82563_REG(0, 26) /* PHY Specific Control 2 */
777 #define GG82563_PHY_PAGE_SELECT_ALT \
778 GG82563_REG(0, 29) /* Alternate Page Select */
780 #define GG82563_PHY_MAC_SPEC_CTRL \
781 GG82563_REG(2, 21) /* MAC Specific Control Register */
783 #define GG82563_PHY_DSP_DISTANCE \
784 GG82563_REG(5, 26) /* DSP Distance */
786 /* Page 193 - Port Control Registers */
787 #define GG82563_PHY_KMRN_MODE_CTRL \
788 GG82563_REG(193, 16) /* Kumeran Mode Control */
789 #define GG82563_PHY_PWR_MGMT_CTRL \
790 GG82563_REG(193, 20) /* Power Management Control */
792 /* Page 194 - KMRN Registers */
793 #define GG82563_PHY_INBAND_CTRL \
794 GG82563_REG(194, 18) /* Inband Control */
797 #define E1000_MDIC_REG_MASK 0x001F0000
798 #define E1000_MDIC_REG_SHIFT 16
799 #define E1000_MDIC_PHY_SHIFT 21
800 #define E1000_MDIC_OP_WRITE 0x04000000
801 #define E1000_MDIC_OP_READ 0x08000000
802 #define E1000_MDIC_READY 0x10000000
803 #define E1000_MDIC_ERROR 0x40000000
806 #define E1000_GEN_POLL_TIMEOUT 640
808 #endif /* _E1000_DEFINES_H_ */
projects / releases.git / blob