1 // SPDX-License-Identifier: GPL-2.0
2 /* Copyright(c) 1999 - 2018 Intel Corporation. */
4 /* 82571EB Gigabit Ethernet Controller
5 * 82571EB Gigabit Ethernet Controller (Copper)
6 * 82571EB Gigabit Ethernet Controller (Fiber)
7 * 82571EB Dual Port Gigabit Mezzanine Adapter
8 * 82571EB Quad Port Gigabit Mezzanine Adapter
9 * 82571PT Gigabit PT Quad Port Server ExpressModule
10 * 82572EI Gigabit Ethernet Controller (Copper)
11 * 82572EI Gigabit Ethernet Controller (Fiber)
12 * 82572EI Gigabit Ethernet Controller
13 * 82573V Gigabit Ethernet Controller (Copper)
14 * 82573E Gigabit Ethernet Controller (Copper)
15 * 82573L Gigabit Ethernet Controller
16 * 82574L Gigabit Network Connection
17 * 82583V Gigabit Network Connection
22 static s32 e1000_get_phy_id_82571(struct e1000_hw *hw);
23 static s32 e1000_setup_copper_link_82571(struct e1000_hw *hw);
24 static s32 e1000_setup_fiber_serdes_link_82571(struct e1000_hw *hw);
25 static s32 e1000_check_for_serdes_link_82571(struct e1000_hw *hw);
26 static s32 e1000_write_nvm_eewr_82571(struct e1000_hw *hw, u16 offset,
27 u16 words, u16 *data);
28 static s32 e1000_fix_nvm_checksum_82571(struct e1000_hw *hw);
29 static void e1000_initialize_hw_bits_82571(struct e1000_hw *hw);
30 static void e1000_clear_hw_cntrs_82571(struct e1000_hw *hw);
31 static bool e1000_check_mng_mode_82574(struct e1000_hw *hw);
32 static s32 e1000_led_on_82574(struct e1000_hw *hw);
33 static void e1000_put_hw_semaphore_82571(struct e1000_hw *hw);
34 static void e1000_power_down_phy_copper_82571(struct e1000_hw *hw);
35 static void e1000_put_hw_semaphore_82573(struct e1000_hw *hw);
36 static s32 e1000_get_hw_semaphore_82574(struct e1000_hw *hw);
37 static void e1000_put_hw_semaphore_82574(struct e1000_hw *hw);
38 static s32 e1000_set_d0_lplu_state_82574(struct e1000_hw *hw, bool active);
39 static s32 e1000_set_d3_lplu_state_82574(struct e1000_hw *hw, bool active);
42 * e1000_init_phy_params_82571 - Init PHY func ptrs.
43 * @hw: pointer to the HW structure
45 static s32 e1000_init_phy_params_82571(struct e1000_hw *hw)
47 struct e1000_phy_info *phy = &hw->phy;
50 if (hw->phy.media_type != e1000_media_type_copper) {
51 phy->type = e1000_phy_none;
56 phy->autoneg_mask = AUTONEG_ADVERTISE_SPEED_DEFAULT;
57 phy->reset_delay_us = 100;
59 phy->ops.power_up = e1000_power_up_phy_copper;
60 phy->ops.power_down = e1000_power_down_phy_copper_82571;
62 switch (hw->mac.type) {
65 phy->type = e1000_phy_igp_2;
68 phy->type = e1000_phy_m88;
72 phy->type = e1000_phy_bm;
73 phy->ops.acquire = e1000_get_hw_semaphore_82574;
74 phy->ops.release = e1000_put_hw_semaphore_82574;
75 phy->ops.set_d0_lplu_state = e1000_set_d0_lplu_state_82574;
76 phy->ops.set_d3_lplu_state = e1000_set_d3_lplu_state_82574;
79 return -E1000_ERR_PHY;
82 /* This can only be done after all function pointers are setup. */
83 ret_val = e1000_get_phy_id_82571(hw);
85 e_dbg("Error getting PHY ID\n");
90 switch (hw->mac.type) {
93 if (phy->id != IGP01E1000_I_PHY_ID)
94 ret_val = -E1000_ERR_PHY;
97 if (phy->id != M88E1111_I_PHY_ID)
98 ret_val = -E1000_ERR_PHY;
102 if (phy->id != BME1000_E_PHY_ID_R2)
103 ret_val = -E1000_ERR_PHY;
106 ret_val = -E1000_ERR_PHY;
111 e_dbg("PHY ID unknown: type = 0x%08x\n", phy->id);
117 * e1000_init_nvm_params_82571 - Init NVM func ptrs.
118 * @hw: pointer to the HW structure
120 static s32 e1000_init_nvm_params_82571(struct e1000_hw *hw)
122 struct e1000_nvm_info *nvm = &hw->nvm;
123 u32 eecd = er32(EECD);
126 nvm->opcode_bits = 8;
128 switch (nvm->override) {
129 case e1000_nvm_override_spi_large:
131 nvm->address_bits = 16;
133 case e1000_nvm_override_spi_small:
135 nvm->address_bits = 8;
138 nvm->page_size = eecd & E1000_EECD_ADDR_BITS ? 32 : 8;
139 nvm->address_bits = eecd & E1000_EECD_ADDR_BITS ? 16 : 8;
143 switch (hw->mac.type) {
147 if (((eecd >> 15) & 0x3) == 0x3) {
148 nvm->type = e1000_nvm_flash_hw;
149 nvm->word_size = 2048;
150 /* Autonomous Flash update bit must be cleared due
151 * to Flash update issue.
153 eecd &= ~E1000_EECD_AUPDEN;
159 nvm->type = e1000_nvm_eeprom_spi;
160 size = (u16)((eecd & E1000_EECD_SIZE_EX_MASK) >>
161 E1000_EECD_SIZE_EX_SHIFT);
162 /* Added to a constant, "size" becomes the left-shift value
163 * for setting word_size.
165 size += NVM_WORD_SIZE_BASE_SHIFT;
167 /* EEPROM access above 16k is unsupported */
170 nvm->word_size = BIT(size);
174 /* Function Pointers */
175 switch (hw->mac.type) {
178 nvm->ops.acquire = e1000_get_hw_semaphore_82574;
179 nvm->ops.release = e1000_put_hw_semaphore_82574;
189 * e1000_init_mac_params_82571 - Init MAC func ptrs.
190 * @hw: pointer to the HW structure
192 static s32 e1000_init_mac_params_82571(struct e1000_hw *hw)
194 struct e1000_mac_info *mac = &hw->mac;
197 bool force_clear_smbi = false;
199 /* Set media type and media-dependent function pointers */
200 switch (hw->adapter->pdev->device) {
201 case E1000_DEV_ID_82571EB_FIBER:
202 case E1000_DEV_ID_82572EI_FIBER:
203 case E1000_DEV_ID_82571EB_QUAD_FIBER:
204 hw->phy.media_type = e1000_media_type_fiber;
205 mac->ops.setup_physical_interface =
206 e1000_setup_fiber_serdes_link_82571;
207 mac->ops.check_for_link = e1000e_check_for_fiber_link;
208 mac->ops.get_link_up_info =
209 e1000e_get_speed_and_duplex_fiber_serdes;
211 case E1000_DEV_ID_82571EB_SERDES:
212 case E1000_DEV_ID_82571EB_SERDES_DUAL:
213 case E1000_DEV_ID_82571EB_SERDES_QUAD:
214 case E1000_DEV_ID_82572EI_SERDES:
215 hw->phy.media_type = e1000_media_type_internal_serdes;
216 mac->ops.setup_physical_interface =
217 e1000_setup_fiber_serdes_link_82571;
218 mac->ops.check_for_link = e1000_check_for_serdes_link_82571;
219 mac->ops.get_link_up_info =
220 e1000e_get_speed_and_duplex_fiber_serdes;
223 hw->phy.media_type = e1000_media_type_copper;
224 mac->ops.setup_physical_interface =
225 e1000_setup_copper_link_82571;
226 mac->ops.check_for_link = e1000e_check_for_copper_link;
227 mac->ops.get_link_up_info = e1000e_get_speed_and_duplex_copper;
231 /* Set mta register count */
232 mac->mta_reg_count = 128;
233 /* Set rar entry count */
234 mac->rar_entry_count = E1000_RAR_ENTRIES;
235 /* Adaptive IFS supported */
236 mac->adaptive_ifs = true;
238 /* MAC-specific function pointers */
239 switch (hw->mac.type) {
241 mac->ops.set_lan_id = e1000_set_lan_id_single_port;
242 mac->ops.check_mng_mode = e1000e_check_mng_mode_generic;
243 mac->ops.led_on = e1000e_led_on_generic;
244 mac->ops.blink_led = e1000e_blink_led_generic;
247 mac->has_fwsm = true;
248 /* ARC supported; valid only if manageability features are
251 mac->arc_subsystem_valid = !!(er32(FWSM) &
252 E1000_FWSM_MODE_MASK);
256 mac->ops.set_lan_id = e1000_set_lan_id_single_port;
257 mac->ops.check_mng_mode = e1000_check_mng_mode_82574;
258 mac->ops.led_on = e1000_led_on_82574;
261 mac->ops.check_mng_mode = e1000e_check_mng_mode_generic;
262 mac->ops.led_on = e1000e_led_on_generic;
263 mac->ops.blink_led = e1000e_blink_led_generic;
266 mac->has_fwsm = true;
270 /* Ensure that the inter-port SWSM.SMBI lock bit is clear before
271 * first NVM or PHY access. This should be done for single-port
272 * devices, and for one port only on dual-port devices so that
273 * for those devices we can still use the SMBI lock to synchronize
274 * inter-port accesses to the PHY & NVM.
276 switch (hw->mac.type) {
281 if (!(swsm2 & E1000_SWSM2_LOCK)) {
282 /* Only do this for the first interface on this card */
283 ew32(SWSM2, swsm2 | E1000_SWSM2_LOCK);
284 force_clear_smbi = true;
286 force_clear_smbi = false;
290 force_clear_smbi = true;
294 if (force_clear_smbi) {
295 /* Make sure SWSM.SMBI is clear */
297 if (swsm & E1000_SWSM_SMBI) {
298 /* This bit should not be set on a first interface, and
299 * indicates that the bootagent or EFI code has
300 * improperly left this bit enabled
302 e_dbg("Please update your 82571 Bootagent\n");
304 ew32(SWSM, swsm & ~E1000_SWSM_SMBI);
307 /* Initialize device specific counter of SMBI acquisition timeouts. */
308 hw->dev_spec.e82571.smb_counter = 0;
313 static s32 e1000_get_variants_82571(struct e1000_adapter *adapter)
315 struct e1000_hw *hw = &adapter->hw;
316 static int global_quad_port_a; /* global port a indication */
317 struct pci_dev *pdev = adapter->pdev;
318 int is_port_b = er32(STATUS) & E1000_STATUS_FUNC_1;
321 rc = e1000_init_mac_params_82571(hw);
325 rc = e1000_init_nvm_params_82571(hw);
329 rc = e1000_init_phy_params_82571(hw);
333 /* tag quad port adapters first, it's used below */
334 switch (pdev->device) {
335 case E1000_DEV_ID_82571EB_QUAD_COPPER:
336 case E1000_DEV_ID_82571EB_QUAD_FIBER:
337 case E1000_DEV_ID_82571EB_QUAD_COPPER_LP:
338 case E1000_DEV_ID_82571PT_QUAD_COPPER:
339 adapter->flags |= FLAG_IS_QUAD_PORT;
340 /* mark the first port */
341 if (global_quad_port_a == 0)
342 adapter->flags |= FLAG_IS_QUAD_PORT_A;
343 /* Reset for multiple quad port adapters */
344 global_quad_port_a++;
345 if (global_quad_port_a == 4)
346 global_quad_port_a = 0;
352 switch (adapter->hw.mac.type) {
354 /* these dual ports don't have WoL on port B at all */
355 if (((pdev->device == E1000_DEV_ID_82571EB_FIBER) ||
356 (pdev->device == E1000_DEV_ID_82571EB_SERDES) ||
357 (pdev->device == E1000_DEV_ID_82571EB_COPPER)) &&
359 adapter->flags &= ~FLAG_HAS_WOL;
360 /* quad ports only support WoL on port A */
361 if (adapter->flags & FLAG_IS_QUAD_PORT &&
362 (!(adapter->flags & FLAG_IS_QUAD_PORT_A)))
363 adapter->flags &= ~FLAG_HAS_WOL;
364 /* Does not support WoL on any port */
365 if (pdev->device == E1000_DEV_ID_82571EB_SERDES_QUAD)
366 adapter->flags &= ~FLAG_HAS_WOL;
369 if (pdev->device == E1000_DEV_ID_82573L) {
370 adapter->flags |= FLAG_HAS_JUMBO_FRAMES;
371 adapter->max_hw_frame_size = DEFAULT_JUMBO;
382 * e1000_get_phy_id_82571 - Retrieve the PHY ID and revision
383 * @hw: pointer to the HW structure
385 * Reads the PHY registers and stores the PHY ID and possibly the PHY
386 * revision in the hardware structure.
388 static s32 e1000_get_phy_id_82571(struct e1000_hw *hw)
390 struct e1000_phy_info *phy = &hw->phy;
394 switch (hw->mac.type) {
397 /* The 82571 firmware may still be configuring the PHY.
398 * In this case, we cannot access the PHY until the
399 * configuration is done. So we explicitly set the
402 phy->id = IGP01E1000_I_PHY_ID;
405 return e1000e_get_phy_id(hw);
408 ret_val = e1e_rphy(hw, MII_PHYSID1, &phy_id);
412 phy->id = (u32)(phy_id << 16);
413 usleep_range(20, 40);
414 ret_val = e1e_rphy(hw, MII_PHYSID2, &phy_id);
418 phy->id |= (u32)(phy_id);
419 phy->revision = (u32)(phy_id & ~PHY_REVISION_MASK);
422 return -E1000_ERR_PHY;
429 * e1000_get_hw_semaphore_82571 - Acquire hardware semaphore
430 * @hw: pointer to the HW structure
432 * Acquire the HW semaphore to access the PHY or NVM
434 static s32 e1000_get_hw_semaphore_82571(struct e1000_hw *hw)
437 s32 sw_timeout = hw->nvm.word_size + 1;
438 s32 fw_timeout = hw->nvm.word_size + 1;
441 /* If we have timedout 3 times on trying to acquire
442 * the inter-port SMBI semaphore, there is old code
443 * operating on the other port, and it is not
444 * releasing SMBI. Modify the number of times that
445 * we try for the semaphore to interwork with this
448 if (hw->dev_spec.e82571.smb_counter > 2)
451 /* Get the SW semaphore */
452 while (i < sw_timeout) {
454 if (!(swsm & E1000_SWSM_SMBI))
457 usleep_range(50, 100);
461 if (i == sw_timeout) {
462 e_dbg("Driver can't access device - SMBI bit is set.\n");
463 hw->dev_spec.e82571.smb_counter++;
465 /* Get the FW semaphore. */
466 for (i = 0; i < fw_timeout; i++) {
468 ew32(SWSM, swsm | E1000_SWSM_SWESMBI);
470 /* Semaphore acquired if bit latched */
471 if (er32(SWSM) & E1000_SWSM_SWESMBI)
474 usleep_range(50, 100);
477 if (i == fw_timeout) {
478 /* Release semaphores */
479 e1000_put_hw_semaphore_82571(hw);
480 e_dbg("Driver can't access the NVM\n");
481 return -E1000_ERR_NVM;
488 * e1000_put_hw_semaphore_82571 - Release hardware semaphore
489 * @hw: pointer to the HW structure
491 * Release hardware semaphore used to access the PHY or NVM
493 static void e1000_put_hw_semaphore_82571(struct e1000_hw *hw)
498 swsm &= ~(E1000_SWSM_SMBI | E1000_SWSM_SWESMBI);
503 * e1000_get_hw_semaphore_82573 - Acquire hardware semaphore
504 * @hw: pointer to the HW structure
506 * Acquire the HW semaphore during reset.
509 static s32 e1000_get_hw_semaphore_82573(struct e1000_hw *hw)
514 extcnf_ctrl = er32(EXTCNF_CTRL);
516 extcnf_ctrl |= E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP;
517 ew32(EXTCNF_CTRL, extcnf_ctrl);
518 extcnf_ctrl = er32(EXTCNF_CTRL);
520 if (extcnf_ctrl & E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP)
523 usleep_range(2000, 4000);
525 } while (i < MDIO_OWNERSHIP_TIMEOUT);
527 if (i == MDIO_OWNERSHIP_TIMEOUT) {
528 /* Release semaphores */
529 e1000_put_hw_semaphore_82573(hw);
530 e_dbg("Driver can't access the PHY\n");
531 return -E1000_ERR_PHY;
538 * e1000_put_hw_semaphore_82573 - Release hardware semaphore
539 * @hw: pointer to the HW structure
541 * Release hardware semaphore used during reset.
544 static void e1000_put_hw_semaphore_82573(struct e1000_hw *hw)
548 extcnf_ctrl = er32(EXTCNF_CTRL);
549 extcnf_ctrl &= ~E1000_EXTCNF_CTRL_MDIO_SW_OWNERSHIP;
550 ew32(EXTCNF_CTRL, extcnf_ctrl);
553 static DEFINE_MUTEX(swflag_mutex);
556 * e1000_get_hw_semaphore_82574 - Acquire hardware semaphore
557 * @hw: pointer to the HW structure
559 * Acquire the HW semaphore to access the PHY or NVM.
562 static s32 e1000_get_hw_semaphore_82574(struct e1000_hw *hw)
566 mutex_lock(&swflag_mutex);
567 ret_val = e1000_get_hw_semaphore_82573(hw);
569 mutex_unlock(&swflag_mutex);
574 * e1000_put_hw_semaphore_82574 - Release hardware semaphore
575 * @hw: pointer to the HW structure
577 * Release hardware semaphore used to access the PHY or NVM
580 static void e1000_put_hw_semaphore_82574(struct e1000_hw *hw)
582 e1000_put_hw_semaphore_82573(hw);
583 mutex_unlock(&swflag_mutex);
587 * e1000_set_d0_lplu_state_82574 - Set Low Power Linkup D0 state
588 * @hw: pointer to the HW structure
589 * @active: true to enable LPLU, false to disable
591 * Sets the LPLU D0 state according to the active flag.
592 * LPLU will not be activated unless the
593 * device autonegotiation advertisement meets standards of
594 * either 10 or 10/100 or 10/100/1000 at all duplexes.
595 * This is a function pointer entry point only called by
596 * PHY setup routines.
598 static s32 e1000_set_d0_lplu_state_82574(struct e1000_hw *hw, bool active)
600 u32 data = er32(POEMB);
603 data |= E1000_PHY_CTRL_D0A_LPLU;
605 data &= ~E1000_PHY_CTRL_D0A_LPLU;
612 * e1000_set_d3_lplu_state_82574 - Sets low power link up state for D3
613 * @hw: pointer to the HW structure
614 * @active: boolean used to enable/disable lplu
616 * The low power link up (lplu) state is set to the power management level D3
617 * when active is true, else clear lplu for D3. LPLU
618 * is used during Dx states where the power conservation is most important.
619 * During driver activity, SmartSpeed should be enabled so performance is
622 static s32 e1000_set_d3_lplu_state_82574(struct e1000_hw *hw, bool active)
624 u32 data = er32(POEMB);
627 data &= ~E1000_PHY_CTRL_NOND0A_LPLU;
628 } else if ((hw->phy.autoneg_advertised == E1000_ALL_SPEED_DUPLEX) ||
629 (hw->phy.autoneg_advertised == E1000_ALL_NOT_GIG) ||
630 (hw->phy.autoneg_advertised == E1000_ALL_10_SPEED)) {
631 data |= E1000_PHY_CTRL_NOND0A_LPLU;
639 * e1000_acquire_nvm_82571 - Request for access to the EEPROM
640 * @hw: pointer to the HW structure
642 * To gain access to the EEPROM, first we must obtain a hardware semaphore.
643 * Then for non-82573 hardware, set the EEPROM access request bit and wait
644 * for EEPROM access grant bit. If the access grant bit is not set, release
645 * hardware semaphore.
647 static s32 e1000_acquire_nvm_82571(struct e1000_hw *hw)
651 ret_val = e1000_get_hw_semaphore_82571(hw);
655 switch (hw->mac.type) {
659 ret_val = e1000e_acquire_nvm(hw);
664 e1000_put_hw_semaphore_82571(hw);
670 * e1000_release_nvm_82571 - Release exclusive access to EEPROM
671 * @hw: pointer to the HW structure
673 * Stop any current commands to the EEPROM and clear the EEPROM request bit.
675 static void e1000_release_nvm_82571(struct e1000_hw *hw)
677 e1000e_release_nvm(hw);
678 e1000_put_hw_semaphore_82571(hw);
682 * e1000_write_nvm_82571 - Write to EEPROM using appropriate interface
683 * @hw: pointer to the HW structure
684 * @offset: offset within the EEPROM to be written to
685 * @words: number of words to write
686 * @data: 16 bit word(s) to be written to the EEPROM
688 * For non-82573 silicon, write data to EEPROM at offset using SPI interface.
690 * If e1000e_update_nvm_checksum is not called after this function, the
691 * EEPROM will most likely contain an invalid checksum.
693 static s32 e1000_write_nvm_82571(struct e1000_hw *hw, u16 offset, u16 words,
698 switch (hw->mac.type) {
702 ret_val = e1000_write_nvm_eewr_82571(hw, offset, words, data);
706 ret_val = e1000e_write_nvm_spi(hw, offset, words, data);
709 ret_val = -E1000_ERR_NVM;
717 * e1000_update_nvm_checksum_82571 - Update EEPROM checksum
718 * @hw: pointer to the HW structure
720 * Updates the EEPROM checksum by reading/adding each word of the EEPROM
721 * up to the checksum. Then calculates the EEPROM checksum and writes the
722 * value to the EEPROM.
724 static s32 e1000_update_nvm_checksum_82571(struct e1000_hw *hw)
730 ret_val = e1000e_update_nvm_checksum_generic(hw);
734 /* If our nvm is an EEPROM, then we're done
735 * otherwise, commit the checksum to the flash NVM.
737 if (hw->nvm.type != e1000_nvm_flash_hw)
740 /* Check for pending operations. */
741 for (i = 0; i < E1000_FLASH_UPDATES; i++) {
742 usleep_range(1000, 2000);
743 if (!(er32(EECD) & E1000_EECD_FLUPD))
747 if (i == E1000_FLASH_UPDATES)
748 return -E1000_ERR_NVM;
750 /* Reset the firmware if using STM opcode. */
751 if ((er32(FLOP) & 0xFF00) == E1000_STM_OPCODE) {
752 /* The enabling of and the actual reset must be done
753 * in two write cycles.
755 ew32(HICR, E1000_HICR_FW_RESET_ENABLE);
757 ew32(HICR, E1000_HICR_FW_RESET);
760 /* Commit the write to flash */
761 eecd = er32(EECD) | E1000_EECD_FLUPD;
764 for (i = 0; i < E1000_FLASH_UPDATES; i++) {
765 usleep_range(1000, 2000);
766 if (!(er32(EECD) & E1000_EECD_FLUPD))
770 if (i == E1000_FLASH_UPDATES)
771 return -E1000_ERR_NVM;
777 * e1000_validate_nvm_checksum_82571 - Validate EEPROM checksum
778 * @hw: pointer to the HW structure
780 * Calculates the EEPROM checksum by reading/adding each word of the EEPROM
781 * and then verifies that the sum of the EEPROM is equal to 0xBABA.
783 static s32 e1000_validate_nvm_checksum_82571(struct e1000_hw *hw)
785 if (hw->nvm.type == e1000_nvm_flash_hw)
786 e1000_fix_nvm_checksum_82571(hw);
788 return e1000e_validate_nvm_checksum_generic(hw);
792 * e1000_write_nvm_eewr_82571 - Write to EEPROM for 82573 silicon
793 * @hw: pointer to the HW structure
794 * @offset: offset within the EEPROM to be written to
795 * @words: number of words to write
796 * @data: 16 bit word(s) to be written to the EEPROM
798 * After checking for invalid values, poll the EEPROM to ensure the previous
799 * command has completed before trying to write the next word. After write
800 * poll for completion.
802 * If e1000e_update_nvm_checksum is not called after this function, the
803 * EEPROM will most likely contain an invalid checksum.
805 static s32 e1000_write_nvm_eewr_82571(struct e1000_hw *hw, u16 offset,
806 u16 words, u16 *data)
808 struct e1000_nvm_info *nvm = &hw->nvm;
812 /* A check for invalid values: offset too large, too many words,
813 * and not enough words.
815 if ((offset >= nvm->word_size) || (words > (nvm->word_size - offset)) ||
817 e_dbg("nvm parameter(s) out of bounds\n");
818 return -E1000_ERR_NVM;
821 for (i = 0; i < words; i++) {
822 eewr = ((data[i] << E1000_NVM_RW_REG_DATA) |
823 ((offset + i) << E1000_NVM_RW_ADDR_SHIFT) |
824 E1000_NVM_RW_REG_START);
826 ret_val = e1000e_poll_eerd_eewr_done(hw, E1000_NVM_POLL_WRITE);
832 ret_val = e1000e_poll_eerd_eewr_done(hw, E1000_NVM_POLL_WRITE);
841 * e1000_get_cfg_done_82571 - Poll for configuration done
842 * @hw: pointer to the HW structure
844 * Reads the management control register for the config done bit to be set.
846 static s32 e1000_get_cfg_done_82571(struct e1000_hw *hw)
848 s32 timeout = PHY_CFG_TIMEOUT;
851 if (er32(EEMNGCTL) & E1000_NVM_CFG_DONE_PORT_0)
853 usleep_range(1000, 2000);
857 e_dbg("MNG configuration cycle has not completed.\n");
858 return -E1000_ERR_RESET;
865 * e1000_set_d0_lplu_state_82571 - Set Low Power Linkup D0 state
866 * @hw: pointer to the HW structure
867 * @active: true to enable LPLU, false to disable
869 * Sets the LPLU D0 state according to the active flag. When activating LPLU
870 * this function also disables smart speed and vice versa. LPLU will not be
871 * activated unless the device autonegotiation advertisement meets standards
872 * of either 10 or 10/100 or 10/100/1000 at all duplexes. This is a function
873 * pointer entry point only called by PHY setup routines.
875 static s32 e1000_set_d0_lplu_state_82571(struct e1000_hw *hw, bool active)
877 struct e1000_phy_info *phy = &hw->phy;
881 ret_val = e1e_rphy(hw, IGP02E1000_PHY_POWER_MGMT, &data);
886 data |= IGP02E1000_PM_D0_LPLU;
887 ret_val = e1e_wphy(hw, IGP02E1000_PHY_POWER_MGMT, data);
891 /* When LPLU is enabled, we should disable SmartSpeed */
892 ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG, &data);
895 data &= ~IGP01E1000_PSCFR_SMART_SPEED;
896 ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG, data);
900 data &= ~IGP02E1000_PM_D0_LPLU;
901 ret_val = e1e_wphy(hw, IGP02E1000_PHY_POWER_MGMT, data);
904 /* LPLU and SmartSpeed are mutually exclusive. LPLU is used
905 * during Dx states where the power conservation is most
906 * important. During driver activity we should enable
907 * SmartSpeed, so performance is maintained.
909 if (phy->smart_speed == e1000_smart_speed_on) {
910 ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG,
915 data |= IGP01E1000_PSCFR_SMART_SPEED;
916 ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG,
920 } else if (phy->smart_speed == e1000_smart_speed_off) {
921 ret_val = e1e_rphy(hw, IGP01E1000_PHY_PORT_CONFIG,
926 data &= ~IGP01E1000_PSCFR_SMART_SPEED;
927 ret_val = e1e_wphy(hw, IGP01E1000_PHY_PORT_CONFIG,
938 * e1000_reset_hw_82571 - Reset hardware
939 * @hw: pointer to the HW structure
941 * This resets the hardware into a known state.
943 static s32 e1000_reset_hw_82571(struct e1000_hw *hw)
945 u32 ctrl, ctrl_ext, eecd, tctl;
948 /* Prevent the PCI-E bus from sticking if there is no TLP connection
949 * on the last TLP read/write transaction when MAC is reset.
951 ret_val = e1000e_disable_pcie_master(hw);
953 e_dbg("PCI-E Master disable polling has failed.\n");
955 e_dbg("Masking off all interrupts\n");
956 ew32(IMC, 0xffffffff);
960 tctl &= ~E1000_TCTL_EN;
964 usleep_range(10000, 11000);
966 /* Must acquire the MDIO ownership before MAC reset.
967 * Ownership defaults to firmware after a reset.
969 switch (hw->mac.type) {
971 ret_val = e1000_get_hw_semaphore_82573(hw);
975 ret_val = e1000_get_hw_semaphore_82574(hw);
983 e_dbg("Issuing a global reset to MAC\n");
984 ew32(CTRL, ctrl | E1000_CTRL_RST);
986 /* Must release MDIO ownership and mutex after MAC reset. */
987 switch (hw->mac.type) {
989 /* Release mutex only if the hw semaphore is acquired */
991 e1000_put_hw_semaphore_82573(hw);
995 /* Release mutex only if the hw semaphore is acquired */
997 e1000_put_hw_semaphore_82574(hw);
1003 if (hw->nvm.type == e1000_nvm_flash_hw) {
1004 usleep_range(10, 20);
1005 ctrl_ext = er32(CTRL_EXT);
1006 ctrl_ext |= E1000_CTRL_EXT_EE_RST;
1007 ew32(CTRL_EXT, ctrl_ext);
1011 ret_val = e1000e_get_auto_rd_done(hw);
1013 /* We don't want to continue accessing MAC registers. */
1016 /* Phy configuration from NVM just starts after EECD_AUTO_RD is set.
1017 * Need to wait for Phy configuration completion before accessing
1021 switch (hw->mac.type) {
1024 /* REQ and GNT bits need to be cleared when using AUTO_RD
1025 * to access the EEPROM.
1028 eecd &= ~(E1000_EECD_REQ | E1000_EECD_GNT);
1040 /* Clear any pending interrupt events. */
1041 ew32(IMC, 0xffffffff);
1044 if (hw->mac.type == e1000_82571) {
1045 /* Install any alternate MAC address into RAR0 */
1046 ret_val = e1000_check_alt_mac_addr_generic(hw);
1050 e1000e_set_laa_state_82571(hw, true);
1053 /* Reinitialize the 82571 serdes link state machine */
1054 if (hw->phy.media_type == e1000_media_type_internal_serdes)
1055 hw->mac.serdes_link_state = e1000_serdes_link_down;
1061 * e1000_init_hw_82571 - Initialize hardware
1062 * @hw: pointer to the HW structure
1064 * This inits the hardware readying it for operation.
1066 static s32 e1000_init_hw_82571(struct e1000_hw *hw)
1068 struct e1000_mac_info *mac = &hw->mac;
1071 u16 i, rar_count = mac->rar_entry_count;
1073 e1000_initialize_hw_bits_82571(hw);
1075 /* Initialize identification LED */
1076 ret_val = mac->ops.id_led_init(hw);
1077 /* An error is not fatal and we should not stop init due to this */
1079 e_dbg("Error initializing identification LED\n");
1081 /* Disabling VLAN filtering */
1082 e_dbg("Initializing the IEEE VLAN\n");
1083 mac->ops.clear_vfta(hw);
1085 /* Setup the receive address.
1086 * If, however, a locally administered address was assigned to the
1087 * 82571, we must reserve a RAR for it to work around an issue where
1088 * resetting one port will reload the MAC on the other port.
1090 if (e1000e_get_laa_state_82571(hw))
1092 e1000e_init_rx_addrs(hw, rar_count);
1094 /* Zero out the Multicast HASH table */
1095 e_dbg("Zeroing the MTA\n");
1096 for (i = 0; i < mac->mta_reg_count; i++)
1097 E1000_WRITE_REG_ARRAY(hw, E1000_MTA, i, 0);
1099 /* Setup link and flow control */
1100 ret_val = mac->ops.setup_link(hw);
1102 /* Set the transmit descriptor write-back policy */
1103 reg_data = er32(TXDCTL(0));
1104 reg_data = ((reg_data & ~E1000_TXDCTL_WTHRESH) |
1105 E1000_TXDCTL_FULL_TX_DESC_WB | E1000_TXDCTL_COUNT_DESC);
1106 ew32(TXDCTL(0), reg_data);
1108 /* ...for both queues. */
1109 switch (mac->type) {
1111 e1000e_enable_tx_pkt_filtering(hw);
1115 reg_data = er32(GCR);
1116 reg_data |= E1000_GCR_L1_ACT_WITHOUT_L0S_RX;
1117 ew32(GCR, reg_data);
1120 reg_data = er32(TXDCTL(1));
1121 reg_data = ((reg_data & ~E1000_TXDCTL_WTHRESH) |
1122 E1000_TXDCTL_FULL_TX_DESC_WB |
1123 E1000_TXDCTL_COUNT_DESC);
1124 ew32(TXDCTL(1), reg_data);
1128 /* Clear all of the statistics registers (clear on read). It is
1129 * important that we do this after we have tried to establish link
1130 * because the symbol error count will increment wildly if there
1133 e1000_clear_hw_cntrs_82571(hw);
1139 * e1000_initialize_hw_bits_82571 - Initialize hardware-dependent bits
1140 * @hw: pointer to the HW structure
1142 * Initializes required hardware-dependent bits needed for normal operation.
1144 static void e1000_initialize_hw_bits_82571(struct e1000_hw *hw)
1148 /* Transmit Descriptor Control 0 */
1149 reg = er32(TXDCTL(0));
1151 ew32(TXDCTL(0), reg);
1153 /* Transmit Descriptor Control 1 */
1154 reg = er32(TXDCTL(1));
1156 ew32(TXDCTL(1), reg);
1158 /* Transmit Arbitration Control 0 */
1159 reg = er32(TARC(0));
1160 reg &= ~(0xF << 27); /* 30:27 */
1161 switch (hw->mac.type) {
1164 reg |= BIT(23) | BIT(24) | BIT(25) | BIT(26);
1175 /* Transmit Arbitration Control 1 */
1176 reg = er32(TARC(1));
1177 switch (hw->mac.type) {
1180 reg &= ~(BIT(29) | BIT(30));
1181 reg |= BIT(22) | BIT(24) | BIT(25) | BIT(26);
1182 if (er32(TCTL) & E1000_TCTL_MULR)
1192 /* Device Control */
1193 switch (hw->mac.type) {
1205 /* Extended Device Control */
1206 switch (hw->mac.type) {
1210 reg = er32(CTRL_EXT);
1213 ew32(CTRL_EXT, reg);
1219 if (hw->mac.type == e1000_82571) {
1220 reg = er32(PBA_ECC);
1221 reg |= E1000_PBA_ECC_CORR_EN;
1225 /* Workaround for hardware errata.
1226 * Ensure that DMA Dynamic Clock gating is disabled on 82571 and 82572
1228 if ((hw->mac.type == e1000_82571) || (hw->mac.type == e1000_82572)) {
1229 reg = er32(CTRL_EXT);
1230 reg &= ~E1000_CTRL_EXT_DMA_DYN_CLK_EN;
1231 ew32(CTRL_EXT, reg);
1234 /* Disable IPv6 extension header parsing because some malformed
1235 * IPv6 headers can hang the Rx.
1237 if (hw->mac.type <= e1000_82573) {
1239 reg |= (E1000_RFCTL_IPV6_EX_DIS | E1000_RFCTL_NEW_IPV6_EXT_DIS);
1243 /* PCI-Ex Control Registers */
1244 switch (hw->mac.type) {
1251 /* Workaround for hardware errata.
1252 * apply workaround for hardware errata documented in errata
1253 * docs Fixes issue where some error prone or unreliable PCIe
1254 * completions are occurring, particularly with ASPM enabled.
1255 * Without fix, issue can cause Tx timeouts.
1267 * e1000_clear_vfta_82571 - Clear VLAN filter table
1268 * @hw: pointer to the HW structure
1270 * Clears the register array which contains the VLAN filter table by
1271 * setting all the values to 0.
1273 static void e1000_clear_vfta_82571(struct e1000_hw *hw)
1277 u32 vfta_offset = 0;
1278 u32 vfta_bit_in_reg = 0;
1280 switch (hw->mac.type) {
1284 if (hw->mng_cookie.vlan_id != 0) {
1285 /* The VFTA is a 4096b bit-field, each identifying
1286 * a single VLAN ID. The following operations
1287 * determine which 32b entry (i.e. offset) into the
1288 * array we want to set the VLAN ID (i.e. bit) of
1289 * the manageability unit.
1291 vfta_offset = (hw->mng_cookie.vlan_id >>
1292 E1000_VFTA_ENTRY_SHIFT) &
1293 E1000_VFTA_ENTRY_MASK;
1295 BIT(hw->mng_cookie.vlan_id &
1296 E1000_VFTA_ENTRY_BIT_SHIFT_MASK);
1302 for (offset = 0; offset < E1000_VLAN_FILTER_TBL_SIZE; offset++) {
1303 /* If the offset we want to clear is the same offset of the
1304 * manageability VLAN ID, then clear all bits except that of
1305 * the manageability unit.
1307 vfta_value = (offset == vfta_offset) ? vfta_bit_in_reg : 0;
1308 E1000_WRITE_REG_ARRAY(hw, E1000_VFTA, offset, vfta_value);
1314 * e1000_check_mng_mode_82574 - Check manageability is enabled
1315 * @hw: pointer to the HW structure
1317 * Reads the NVM Initialization Control Word 2 and returns true
1318 * (>0) if any manageability is enabled, else false (0).
1320 static bool e1000_check_mng_mode_82574(struct e1000_hw *hw)
1324 e1000_read_nvm(hw, NVM_INIT_CONTROL2_REG, 1, &data);
1325 return (data & E1000_NVM_INIT_CTRL2_MNGM) != 0;
1329 * e1000_led_on_82574 - Turn LED on
1330 * @hw: pointer to the HW structure
1334 static s32 e1000_led_on_82574(struct e1000_hw *hw)
1339 ctrl = hw->mac.ledctl_mode2;
1340 if (!(E1000_STATUS_LU & er32(STATUS))) {
1341 /* If no link, then turn LED on by setting the invert bit
1342 * for each LED that's "on" (0x0E) in ledctl_mode2.
1344 for (i = 0; i < 4; i++)
1345 if (((hw->mac.ledctl_mode2 >> (i * 8)) & 0xFF) ==
1346 E1000_LEDCTL_MODE_LED_ON)
1347 ctrl |= (E1000_LEDCTL_LED0_IVRT << (i * 8));
1355 * e1000_check_phy_82574 - check 82574 phy hung state
1356 * @hw: pointer to the HW structure
1358 * Returns whether phy is hung or not
1360 bool e1000_check_phy_82574(struct e1000_hw *hw)
1362 u16 status_1kbt = 0;
1363 u16 receive_errors = 0;
1366 /* Read PHY Receive Error counter first, if its is max - all F's then
1367 * read the Base1000T status register If both are max then PHY is hung.
1369 ret_val = e1e_rphy(hw, E1000_RECEIVE_ERROR_COUNTER, &receive_errors);
1372 if (receive_errors == E1000_RECEIVE_ERROR_MAX) {
1373 ret_val = e1e_rphy(hw, E1000_BASE1000T_STATUS, &status_1kbt);
1376 if ((status_1kbt & E1000_IDLE_ERROR_COUNT_MASK) ==
1377 E1000_IDLE_ERROR_COUNT_MASK)
1385 * e1000_setup_link_82571 - Setup flow control and link settings
1386 * @hw: pointer to the HW structure
1388 * Determines which flow control settings to use, then configures flow
1389 * control. Calls the appropriate media-specific link configuration
1390 * function. Assuming the adapter has a valid link partner, a valid link
1391 * should be established. Assumes the hardware has previously been reset
1392 * and the transmitter and receiver are not enabled.
1394 static s32 e1000_setup_link_82571(struct e1000_hw *hw)
1396 /* 82573 does not have a word in the NVM to determine
1397 * the default flow control setting, so we explicitly
1400 switch (hw->mac.type) {
1404 if (hw->fc.requested_mode == e1000_fc_default)
1405 hw->fc.requested_mode = e1000_fc_full;
1411 return e1000e_setup_link_generic(hw);
1415 * e1000_setup_copper_link_82571 - Configure copper link settings
1416 * @hw: pointer to the HW structure
1418 * Configures the link for auto-neg or forced speed and duplex. Then we check
1419 * for link, once link is established calls to configure collision distance
1420 * and flow control are called.
1422 static s32 e1000_setup_copper_link_82571(struct e1000_hw *hw)
1428 ctrl |= E1000_CTRL_SLU;
1429 ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
1432 switch (hw->phy.type) {
1435 ret_val = e1000e_copper_link_setup_m88(hw);
1437 case e1000_phy_igp_2:
1438 ret_val = e1000e_copper_link_setup_igp(hw);
1441 return -E1000_ERR_PHY;
1447 return e1000e_setup_copper_link(hw);
1451 * e1000_setup_fiber_serdes_link_82571 - Setup link for fiber/serdes
1452 * @hw: pointer to the HW structure
1454 * Configures collision distance and flow control for fiber and serdes links.
1455 * Upon successful setup, poll for link.
1457 static s32 e1000_setup_fiber_serdes_link_82571(struct e1000_hw *hw)
1459 switch (hw->mac.type) {
1462 /* If SerDes loopback mode is entered, there is no form
1463 * of reset to take the adapter out of that mode. So we
1464 * have to explicitly take the adapter out of loopback
1465 * mode. This prevents drivers from twiddling their thumbs
1466 * if another tool failed to take it out of loopback mode.
1468 ew32(SCTL, E1000_SCTL_DISABLE_SERDES_LOOPBACK);
1474 return e1000e_setup_fiber_serdes_link(hw);
1478 * e1000_check_for_serdes_link_82571 - Check for link (Serdes)
1479 * @hw: pointer to the HW structure
1481 * Reports the link state as up or down.
1483 * If autonegotiation is supported by the link partner, the link state is
1484 * determined by the result of autonegotiation. This is the most likely case.
1485 * If autonegotiation is not supported by the link partner, and the link
1486 * has a valid signal, force the link up.
1488 * The link state is represented internally here by 4 states:
1491 * 2) autoneg_progress
1492 * 3) autoneg_complete (the link successfully autonegotiated)
1493 * 4) forced_up (the link has been forced up, it did not autonegotiate)
1496 static s32 e1000_check_for_serdes_link_82571(struct e1000_hw *hw)
1498 struct e1000_mac_info *mac = &hw->mac;
1507 status = er32(STATUS);
1509 /* SYNCH bit and IV bit are sticky */
1510 usleep_range(10, 20);
1513 if ((rxcw & E1000_RXCW_SYNCH) && !(rxcw & E1000_RXCW_IV)) {
1514 /* Receiver is synchronized with no invalid bits. */
1515 switch (mac->serdes_link_state) {
1516 case e1000_serdes_link_autoneg_complete:
1517 if (!(status & E1000_STATUS_LU)) {
1518 /* We have lost link, retry autoneg before
1519 * reporting link failure
1521 mac->serdes_link_state =
1522 e1000_serdes_link_autoneg_progress;
1523 mac->serdes_has_link = false;
1524 e_dbg("AN_UP -> AN_PROG\n");
1526 mac->serdes_has_link = true;
1530 case e1000_serdes_link_forced_up:
1531 /* If we are receiving /C/ ordered sets, re-enable
1532 * auto-negotiation in the TXCW register and disable
1533 * forced link in the Device Control register in an
1534 * attempt to auto-negotiate with our link partner.
1536 if (rxcw & E1000_RXCW_C) {
1537 /* Enable autoneg, and unforce link up */
1538 ew32(TXCW, mac->txcw);
1539 ew32(CTRL, (ctrl & ~E1000_CTRL_SLU));
1540 mac->serdes_link_state =
1541 e1000_serdes_link_autoneg_progress;
1542 mac->serdes_has_link = false;
1543 e_dbg("FORCED_UP -> AN_PROG\n");
1545 mac->serdes_has_link = true;
1549 case e1000_serdes_link_autoneg_progress:
1550 if (rxcw & E1000_RXCW_C) {
1551 /* We received /C/ ordered sets, meaning the
1552 * link partner has autonegotiated, and we can
1553 * trust the Link Up (LU) status bit.
1555 if (status & E1000_STATUS_LU) {
1556 mac->serdes_link_state =
1557 e1000_serdes_link_autoneg_complete;
1558 e_dbg("AN_PROG -> AN_UP\n");
1559 mac->serdes_has_link = true;
1561 /* Autoneg completed, but failed. */
1562 mac->serdes_link_state =
1563 e1000_serdes_link_down;
1564 e_dbg("AN_PROG -> DOWN\n");
1567 /* The link partner did not autoneg.
1568 * Force link up and full duplex, and change
1571 ew32(TXCW, (mac->txcw & ~E1000_TXCW_ANE));
1572 ctrl |= (E1000_CTRL_SLU | E1000_CTRL_FD);
1575 /* Configure Flow Control after link up. */
1576 ret_val = e1000e_config_fc_after_link_up(hw);
1578 e_dbg("Error config flow control\n");
1581 mac->serdes_link_state =
1582 e1000_serdes_link_forced_up;
1583 mac->serdes_has_link = true;
1584 e_dbg("AN_PROG -> FORCED_UP\n");
1588 case e1000_serdes_link_down:
1590 /* The link was down but the receiver has now gained
1591 * valid sync, so lets see if we can bring the link
1594 ew32(TXCW, mac->txcw);
1595 ew32(CTRL, (ctrl & ~E1000_CTRL_SLU));
1596 mac->serdes_link_state =
1597 e1000_serdes_link_autoneg_progress;
1598 mac->serdes_has_link = false;
1599 e_dbg("DOWN -> AN_PROG\n");
1603 if (!(rxcw & E1000_RXCW_SYNCH)) {
1604 mac->serdes_has_link = false;
1605 mac->serdes_link_state = e1000_serdes_link_down;
1606 e_dbg("ANYSTATE -> DOWN\n");
1608 /* Check several times, if SYNCH bit and CONFIG
1609 * bit both are consistently 1 then simply ignore
1610 * the IV bit and restart Autoneg
1612 for (i = 0; i < AN_RETRY_COUNT; i++) {
1613 usleep_range(10, 20);
1615 if ((rxcw & E1000_RXCW_SYNCH) &&
1616 (rxcw & E1000_RXCW_C))
1619 if (rxcw & E1000_RXCW_IV) {
1620 mac->serdes_has_link = false;
1621 mac->serdes_link_state =
1622 e1000_serdes_link_down;
1623 e_dbg("ANYSTATE -> DOWN\n");
1628 if (i == AN_RETRY_COUNT) {
1630 txcw |= E1000_TXCW_ANE;
1632 mac->serdes_link_state =
1633 e1000_serdes_link_autoneg_progress;
1634 mac->serdes_has_link = false;
1635 e_dbg("ANYSTATE -> AN_PROG\n");
1644 * e1000_valid_led_default_82571 - Verify a valid default LED config
1645 * @hw: pointer to the HW structure
1646 * @data: pointer to the NVM (EEPROM)
1648 * Read the EEPROM for the current default LED configuration. If the
1649 * LED configuration is not valid, set to a valid LED configuration.
1651 static s32 e1000_valid_led_default_82571(struct e1000_hw *hw, u16 *data)
1655 ret_val = e1000_read_nvm(hw, NVM_ID_LED_SETTINGS, 1, data);
1657 e_dbg("NVM Read Error\n");
1661 switch (hw->mac.type) {
1665 if (*data == ID_LED_RESERVED_F746)
1666 *data = ID_LED_DEFAULT_82573;
1669 if (*data == ID_LED_RESERVED_0000 ||
1670 *data == ID_LED_RESERVED_FFFF)
1671 *data = ID_LED_DEFAULT;
1679 * e1000e_get_laa_state_82571 - Get locally administered address state
1680 * @hw: pointer to the HW structure
1682 * Retrieve and return the current locally administered address state.
1684 bool e1000e_get_laa_state_82571(struct e1000_hw *hw)
1686 if (hw->mac.type != e1000_82571)
1689 return hw->dev_spec.e82571.laa_is_present;
1693 * e1000e_set_laa_state_82571 - Set locally administered address state
1694 * @hw: pointer to the HW structure
1695 * @state: enable/disable locally administered address
1697 * Enable/Disable the current locally administered address state.
1699 void e1000e_set_laa_state_82571(struct e1000_hw *hw, bool state)
1701 if (hw->mac.type != e1000_82571)
1704 hw->dev_spec.e82571.laa_is_present = state;
1706 /* If workaround is activated... */
1708 /* Hold a copy of the LAA in RAR[14] This is done so that
1709 * between the time RAR[0] gets clobbered and the time it
1710 * gets fixed, the actual LAA is in one of the RARs and no
1711 * incoming packets directed to this port are dropped.
1712 * Eventually the LAA will be in RAR[0] and RAR[14].
1714 hw->mac.ops.rar_set(hw, hw->mac.addr,
1715 hw->mac.rar_entry_count - 1);
1719 * e1000_fix_nvm_checksum_82571 - Fix EEPROM checksum
1720 * @hw: pointer to the HW structure
1722 * Verifies that the EEPROM has completed the update. After updating the
1723 * EEPROM, we need to check bit 15 in work 0x23 for the checksum fix. If
1724 * the checksum fix is not implemented, we need to set the bit and update
1725 * the checksum. Otherwise, if bit 15 is set and the checksum is incorrect,
1726 * we need to return bad checksum.
1728 static s32 e1000_fix_nvm_checksum_82571(struct e1000_hw *hw)
1730 struct e1000_nvm_info *nvm = &hw->nvm;
1734 if (nvm->type != e1000_nvm_flash_hw)
1737 /* Check bit 4 of word 10h. If it is 0, firmware is done updating
1738 * 10h-12h. Checksum may need to be fixed.
1740 ret_val = e1000_read_nvm(hw, 0x10, 1, &data);
1744 if (!(data & 0x10)) {
1745 /* Read 0x23 and check bit 15. This bit is a 1
1746 * when the checksum has already been fixed. If
1747 * the checksum is still wrong and this bit is a
1748 * 1, we need to return bad checksum. Otherwise,
1749 * we need to set this bit to a 1 and update the
1752 ret_val = e1000_read_nvm(hw, 0x23, 1, &data);
1756 if (!(data & 0x8000)) {
1758 ret_val = e1000_write_nvm(hw, 0x23, 1, &data);
1761 ret_val = e1000e_update_nvm_checksum(hw);
1771 * e1000_read_mac_addr_82571 - Read device MAC address
1772 * @hw: pointer to the HW structure
1774 static s32 e1000_read_mac_addr_82571(struct e1000_hw *hw)
1776 if (hw->mac.type == e1000_82571) {
1779 /* If there's an alternate MAC address place it in RAR0
1780 * so that it will override the Si installed default perm
1783 ret_val = e1000_check_alt_mac_addr_generic(hw);
1788 return e1000_read_mac_addr_generic(hw);
1792 * e1000_power_down_phy_copper_82571 - Remove link during PHY power down
1793 * @hw: pointer to the HW structure
1795 * In the case of a PHY power down to save power, or to turn off link during a
1796 * driver unload, or wake on lan is not enabled, remove the link.
1798 static void e1000_power_down_phy_copper_82571(struct e1000_hw *hw)
1800 struct e1000_phy_info *phy = &hw->phy;
1801 struct e1000_mac_info *mac = &hw->mac;
1803 if (!phy->ops.check_reset_block)
1806 /* If the management interface is not enabled, then power down */
1807 if (!(mac->ops.check_mng_mode(hw) || phy->ops.check_reset_block(hw)))
1808 e1000_power_down_phy_copper(hw);
1812 * e1000_clear_hw_cntrs_82571 - Clear device specific hardware counters
1813 * @hw: pointer to the HW structure
1815 * Clears the hardware counters by reading the counter registers.
1817 static void e1000_clear_hw_cntrs_82571(struct e1000_hw *hw)
1819 e1000e_clear_hw_cntrs_base(hw);
1857 static const struct e1000_mac_operations e82571_mac_ops = {
1858 /* .check_mng_mode: mac type dependent */
1859 /* .check_for_link: media type dependent */
1860 .id_led_init = e1000e_id_led_init_generic,
1861 .cleanup_led = e1000e_cleanup_led_generic,
1862 .clear_hw_cntrs = e1000_clear_hw_cntrs_82571,
1863 .get_bus_info = e1000e_get_bus_info_pcie,
1864 .set_lan_id = e1000_set_lan_id_multi_port_pcie,
1865 /* .get_link_up_info: media type dependent */
1866 /* .led_on: mac type dependent */
1867 .led_off = e1000e_led_off_generic,
1868 .update_mc_addr_list = e1000e_update_mc_addr_list_generic,
1869 .write_vfta = e1000_write_vfta_generic,
1870 .clear_vfta = e1000_clear_vfta_82571,
1871 .reset_hw = e1000_reset_hw_82571,
1872 .init_hw = e1000_init_hw_82571,
1873 .setup_link = e1000_setup_link_82571,
1874 /* .setup_physical_interface: media type dependent */
1875 .setup_led = e1000e_setup_led_generic,
1876 .config_collision_dist = e1000e_config_collision_dist_generic,
1877 .read_mac_addr = e1000_read_mac_addr_82571,
1878 .rar_set = e1000e_rar_set_generic,
1879 .rar_get_count = e1000e_rar_get_count_generic,
1882 static const struct e1000_phy_operations e82_phy_ops_igp = {
1883 .acquire = e1000_get_hw_semaphore_82571,
1884 .check_polarity = e1000_check_polarity_igp,
1885 .check_reset_block = e1000e_check_reset_block_generic,
1887 .force_speed_duplex = e1000e_phy_force_speed_duplex_igp,
1888 .get_cfg_done = e1000_get_cfg_done_82571,
1889 .get_cable_length = e1000e_get_cable_length_igp_2,
1890 .get_info = e1000e_get_phy_info_igp,
1891 .read_reg = e1000e_read_phy_reg_igp,
1892 .release = e1000_put_hw_semaphore_82571,
1893 .reset = e1000e_phy_hw_reset_generic,
1894 .set_d0_lplu_state = e1000_set_d0_lplu_state_82571,
1895 .set_d3_lplu_state = e1000e_set_d3_lplu_state,
1896 .write_reg = e1000e_write_phy_reg_igp,
1897 .cfg_on_link_up = NULL,
1900 static const struct e1000_phy_operations e82_phy_ops_m88 = {
1901 .acquire = e1000_get_hw_semaphore_82571,
1902 .check_polarity = e1000_check_polarity_m88,
1903 .check_reset_block = e1000e_check_reset_block_generic,
1904 .commit = e1000e_phy_sw_reset,
1905 .force_speed_duplex = e1000e_phy_force_speed_duplex_m88,
1906 .get_cfg_done = e1000e_get_cfg_done_generic,
1907 .get_cable_length = e1000e_get_cable_length_m88,
1908 .get_info = e1000e_get_phy_info_m88,
1909 .read_reg = e1000e_read_phy_reg_m88,
1910 .release = e1000_put_hw_semaphore_82571,
1911 .reset = e1000e_phy_hw_reset_generic,
1912 .set_d0_lplu_state = e1000_set_d0_lplu_state_82571,
1913 .set_d3_lplu_state = e1000e_set_d3_lplu_state,
1914 .write_reg = e1000e_write_phy_reg_m88,
1915 .cfg_on_link_up = NULL,
1918 static const struct e1000_phy_operations e82_phy_ops_bm = {
1919 .acquire = e1000_get_hw_semaphore_82571,
1920 .check_polarity = e1000_check_polarity_m88,
1921 .check_reset_block = e1000e_check_reset_block_generic,
1922 .commit = e1000e_phy_sw_reset,
1923 .force_speed_duplex = e1000e_phy_force_speed_duplex_m88,
1924 .get_cfg_done = e1000e_get_cfg_done_generic,
1925 .get_cable_length = e1000e_get_cable_length_m88,
1926 .get_info = e1000e_get_phy_info_m88,
1927 .read_reg = e1000e_read_phy_reg_bm2,
1928 .release = e1000_put_hw_semaphore_82571,
1929 .reset = e1000e_phy_hw_reset_generic,
1930 .set_d0_lplu_state = e1000_set_d0_lplu_state_82571,
1931 .set_d3_lplu_state = e1000e_set_d3_lplu_state,
1932 .write_reg = e1000e_write_phy_reg_bm2,
1933 .cfg_on_link_up = NULL,
1936 static const struct e1000_nvm_operations e82571_nvm_ops = {
1937 .acquire = e1000_acquire_nvm_82571,
1938 .read = e1000e_read_nvm_eerd,
1939 .release = e1000_release_nvm_82571,
1940 .reload = e1000e_reload_nvm_generic,
1941 .update = e1000_update_nvm_checksum_82571,
1942 .valid_led_default = e1000_valid_led_default_82571,
1943 .validate = e1000_validate_nvm_checksum_82571,
1944 .write = e1000_write_nvm_82571,
1947 const struct e1000_info e1000_82571_info = {
1949 .flags = FLAG_HAS_HW_VLAN_FILTER
1950 | FLAG_HAS_JUMBO_FRAMES
1952 | FLAG_APME_IN_CTRL3
1953 | FLAG_HAS_CTRLEXT_ON_LOAD
1954 | FLAG_HAS_SMART_POWER_DOWN
1955 | FLAG_RESET_OVERWRITES_LAA /* errata */
1956 | FLAG_TARC_SPEED_MODE_BIT /* errata */
1957 | FLAG_APME_CHECK_PORT_B,
1958 .flags2 = FLAG2_DISABLE_ASPM_L1 /* errata 13 */
1961 .max_hw_frame_size = DEFAULT_JUMBO,
1962 .get_variants = e1000_get_variants_82571,
1963 .mac_ops = &e82571_mac_ops,
1964 .phy_ops = &e82_phy_ops_igp,
1965 .nvm_ops = &e82571_nvm_ops,
1968 const struct e1000_info e1000_82572_info = {
1970 .flags = FLAG_HAS_HW_VLAN_FILTER
1971 | FLAG_HAS_JUMBO_FRAMES
1973 | FLAG_APME_IN_CTRL3
1974 | FLAG_HAS_CTRLEXT_ON_LOAD
1975 | FLAG_TARC_SPEED_MODE_BIT, /* errata */
1976 .flags2 = FLAG2_DISABLE_ASPM_L1 /* errata 13 */
1979 .max_hw_frame_size = DEFAULT_JUMBO,
1980 .get_variants = e1000_get_variants_82571,
1981 .mac_ops = &e82571_mac_ops,
1982 .phy_ops = &e82_phy_ops_igp,
1983 .nvm_ops = &e82571_nvm_ops,
1986 const struct e1000_info e1000_82573_info = {
1988 .flags = FLAG_HAS_HW_VLAN_FILTER
1990 | FLAG_APME_IN_CTRL3
1991 | FLAG_HAS_SMART_POWER_DOWN
1993 | FLAG_HAS_SWSM_ON_LOAD,
1994 .flags2 = FLAG2_DISABLE_ASPM_L1
1995 | FLAG2_DISABLE_ASPM_L0S,
1997 .max_hw_frame_size = VLAN_ETH_FRAME_LEN + ETH_FCS_LEN,
1998 .get_variants = e1000_get_variants_82571,
1999 .mac_ops = &e82571_mac_ops,
2000 .phy_ops = &e82_phy_ops_m88,
2001 .nvm_ops = &e82571_nvm_ops,
2004 const struct e1000_info e1000_82574_info = {
2006 .flags = FLAG_HAS_HW_VLAN_FILTER
2008 | FLAG_HAS_JUMBO_FRAMES
2010 | FLAG_HAS_HW_TIMESTAMP
2011 | FLAG_APME_IN_CTRL3
2012 | FLAG_HAS_SMART_POWER_DOWN
2014 | FLAG_HAS_CTRLEXT_ON_LOAD,
2015 .flags2 = FLAG2_CHECK_PHY_HANG
2016 | FLAG2_DISABLE_ASPM_L0S
2017 | FLAG2_DISABLE_ASPM_L1
2018 | FLAG2_NO_DISABLE_RX
2020 | FLAG2_CHECK_SYSTIM_OVERFLOW,
2022 .max_hw_frame_size = DEFAULT_JUMBO,
2023 .get_variants = e1000_get_variants_82571,
2024 .mac_ops = &e82571_mac_ops,
2025 .phy_ops = &e82_phy_ops_bm,
2026 .nvm_ops = &e82571_nvm_ops,
2029 const struct e1000_info e1000_82583_info = {
2031 .flags = FLAG_HAS_HW_VLAN_FILTER
2033 | FLAG_HAS_HW_TIMESTAMP
2034 | FLAG_APME_IN_CTRL3
2035 | FLAG_HAS_SMART_POWER_DOWN
2037 | FLAG_HAS_JUMBO_FRAMES
2038 | FLAG_HAS_CTRLEXT_ON_LOAD,
2039 .flags2 = FLAG2_DISABLE_ASPM_L0S
2040 | FLAG2_DISABLE_ASPM_L1
2041 | FLAG2_NO_DISABLE_RX
2042 | FLAG2_CHECK_SYSTIM_OVERFLOW,
2044 .max_hw_frame_size = DEFAULT_JUMBO,
2045 .get_variants = e1000_get_variants_82571,
2046 .mac_ops = &e82571_mac_ops,
2047 .phy_ops = &e82_phy_ops_bm,
2048 .nvm_ops = &e82571_nvm_ops,