drivers/most/most_usb.c

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * usb.c - Hardware dependent module for USB
   4  *
   5  * Copyright (C) 2013-2015 Microchip Technology Germany II GmbH & Co. KG
   6  */
   7
   8 #include <linux/module.h>
   9 #include <linux/fs.h>
  10 #include <linux/usb.h>
  11 #include <linux/slab.h>
  12 #include <linux/init.h>
  13 #include <linux/cdev.h>
  14 #include <linux/device.h>
  15 #include <linux/list.h>
  16 #include <linux/completion.h>
  17 #include <linux/mutex.h>
  18 #include <linux/spinlock.h>
  19 #include <linux/interrupt.h>
  20 #include <linux/workqueue.h>
  21 #include <linux/sysfs.h>
  22 #include <linux/dma-mapping.h>
  23 #include <linux/etherdevice.h>
  24 #include <linux/uaccess.h>
  25 #include <linux/most.h>
  26
  27 #define USB_MTU                 512
  28 #define NO_ISOCHRONOUS_URB      0
  29 #define AV_PACKETS_PER_XACT     2
  30 #define BUF_CHAIN_SIZE          0xFFFF
  31 #define MAX_NUM_ENDPOINTS       30
  32 #define MAX_SUFFIX_LEN          10
  33 #define MAX_STRING_LEN          80
  34 #define MAX_BUF_SIZE            0xFFFF
  35
  36 #define USB_VENDOR_ID_SMSC      0x0424  /* VID: SMSC */
  37 #define USB_DEV_ID_BRDG         0xC001  /* PID: USB Bridge */
  38 #define USB_DEV_ID_OS81118      0xCF18  /* PID: USB OS81118 */
  39 #define USB_DEV_ID_OS81119      0xCF19  /* PID: USB OS81119 */
  40 #define USB_DEV_ID_OS81210      0xCF30  /* PID: USB OS81210 */
  41 /* DRCI Addresses */
  42 #define DRCI_REG_NI_STATE       0x0100
  43 #define DRCI_REG_PACKET_BW      0x0101
  44 #define DRCI_REG_NODE_ADDR      0x0102
  45 #define DRCI_REG_NODE_POS       0x0103
  46 #define DRCI_REG_MEP_FILTER     0x0140
  47 #define DRCI_REG_HASH_TBL0      0x0141
  48 #define DRCI_REG_HASH_TBL1      0x0142
  49 #define DRCI_REG_HASH_TBL2      0x0143
  50 #define DRCI_REG_HASH_TBL3      0x0144
  51 #define DRCI_REG_HW_ADDR_HI     0x0145
  52 #define DRCI_REG_HW_ADDR_MI     0x0146
  53 #define DRCI_REG_HW_ADDR_LO     0x0147
  54 #define DRCI_REG_BASE           0x1100
  55 #define DRCI_COMMAND            0x02
  56 #define DRCI_READ_REQ           0xA0
  57 #define DRCI_WRITE_REQ          0xA1
  58
  59 /**
  60  * struct most_dci_obj - Direct Communication Interface
  61  * @kobj:position in sysfs
  62  * @usb_device: pointer to the usb device
  63  * @reg_addr: register address for arbitrary DCI access
  64  */
  65 struct most_dci_obj {
  66         struct device dev;
  67         struct usb_device *usb_device;
  68         u16 reg_addr;
  69 };
  70
  71 #define to_dci_obj(p) container_of(p, struct most_dci_obj, dev)
  72
  73 struct most_dev;
  74
  75 struct clear_hold_work {
  76         struct work_struct ws;
  77         struct most_dev *mdev;
  78         unsigned int channel;
  79         int pipe;
  80 };
  81
  82 #define to_clear_hold_work(w) container_of(w, struct clear_hold_work, ws)
  83
  84 /**
  85  * struct most_dev - holds all usb interface specific stuff
  86  * @usb_device: pointer to usb device
  87  * @iface: hardware interface
  88  * @cap: channel capabilities
  89  * @conf: channel configuration
  90  * @dci: direct communication interface of hardware
  91  * @ep_address: endpoint address table
  92  * @description: device description
  93  * @suffix: suffix for channel name
  94  * @channel_lock: synchronize channel access
  95  * @padding_active: indicates channel uses padding
  96  * @is_channel_healthy: health status table of each channel
  97  * @busy_urbs: list of anchored items
  98  * @io_mutex: synchronize I/O with disconnect
  99  * @link_stat_timer: timer for link status reports
 100  * @poll_work_obj: work for polling link status
 101  */
 102 struct most_dev {
 103         struct device dev;
 104         struct usb_device *usb_device;
 105         struct most_interface iface;
 106         struct most_channel_capability *cap;
 107         struct most_channel_config *conf;
 108         struct most_dci_obj *dci;
 109         u8 *ep_address;
 110         char description[MAX_STRING_LEN];
 111         char suffix[MAX_NUM_ENDPOINTS][MAX_SUFFIX_LEN];
 112         spinlock_t channel_lock[MAX_NUM_ENDPOINTS]; /* sync channel access */
 113         bool padding_active[MAX_NUM_ENDPOINTS];
 114         bool is_channel_healthy[MAX_NUM_ENDPOINTS];
 115         struct clear_hold_work clear_work[MAX_NUM_ENDPOINTS];
 116         struct usb_anchor *busy_urbs;
 117         struct mutex io_mutex;
 118         struct timer_list link_stat_timer;
 119         struct work_struct poll_work_obj;
 120         void (*on_netinfo)(struct most_interface *most_iface,
 121                            unsigned char link_state, unsigned char *addrs);
 122 };
 123
 124 #define to_mdev(d) container_of(d, struct most_dev, iface)
 125 #define to_mdev_from_dev(d) container_of(d, struct most_dev, dev)
 126 #define to_mdev_from_work(w) container_of(w, struct most_dev, poll_work_obj)
 127
 128 static void wq_clear_halt(struct work_struct *wq_obj);
 129 static void wq_netinfo(struct work_struct *wq_obj);
 130
 131 /**
 132  * drci_rd_reg - read a DCI register
 133  * @dev: usb device
 134  * @reg: register address
 135  * @buf: buffer to store data
 136  *
 137  * This is reads data from INIC's direct register communication interface
 138  */
 139 static inline int drci_rd_reg(struct usb_device *dev, u16 reg, u16 *buf)
 140 {
 141         int retval;
 142         __le16 *dma_buf;
 143         u8 req_type = USB_DIR_IN | USB_TYPE_VENDOR | USB_RECIP_DEVICE;
 144
 145         dma_buf = kzalloc(sizeof(*dma_buf), GFP_KERNEL);
 146         if (!dma_buf)
 147                 return -ENOMEM;
 148
 149         retval = usb_control_msg(dev, usb_rcvctrlpipe(dev, 0),
 150                                  DRCI_READ_REQ, req_type,
 151                                  0x0000,
 152                                  reg, dma_buf, sizeof(*dma_buf),
 153                                  USB_CTRL_GET_TIMEOUT);
 154         *buf = le16_to_cpu(*dma_buf);
 155         kfree(dma_buf);
 156
 157         if (retval < 0)
 158                 return retval;
 159         return 0;
 160 }
 161
 162 /**
 163  * drci_wr_reg - write a DCI register
 164  * @dev: usb device
 165  * @reg: register address
 166  * @data: data to write
 167  *
 168  * This is writes data to INIC's direct register communication interface
 169  */
 170 static inline int drci_wr_reg(struct usb_device *dev, u16 reg, u16 data)
 171 {
 172         return usb_control_msg(dev,
 173                                usb_sndctrlpipe(dev, 0),
 174                                DRCI_WRITE_REQ,
 175                                USB_DIR_OUT | USB_TYPE_VENDOR | USB_RECIP_DEVICE,
 176                                data,
 177                                reg,
 178                                NULL,
 179                                0,
 180                                USB_CTRL_SET_TIMEOUT);
 181 }
 182
 183 static inline int start_sync_ep(struct usb_device *usb_dev, u16 ep)
 184 {
 185         return drci_wr_reg(usb_dev, DRCI_REG_BASE + DRCI_COMMAND + ep * 16, 1);
 186 }
 187
 188 /**
 189  * get_stream_frame_size - calculate frame size of current configuration
 190  * @dev: device structure
 191  * @cfg: channel configuration
 192  */
 193 static unsigned int get_stream_frame_size(struct device *dev,
 194                                           struct most_channel_config *cfg)
 195 {
 196         unsigned int frame_size;
 197         unsigned int sub_size = cfg->subbuffer_size;
 198
 199         if (!sub_size) {
 200                 dev_warn(dev, "Misconfig: Subbuffer size zero.\n");
 201                 return 0;
 202         }
 203         switch (cfg->data_type) {
 204         case MOST_CH_ISOC:
 205                 frame_size = AV_PACKETS_PER_XACT * sub_size;
 206                 break;
 207         case MOST_CH_SYNC:
 208                 if (cfg->packets_per_xact == 0) {
 209                         dev_warn(dev, "Misconfig: Packets per XACT zero\n");
 210                         frame_size = 0;
 211                 } else if (cfg->packets_per_xact == 0xFF) {
 212                         frame_size = (USB_MTU / sub_size) * sub_size;
 213                 } else {
 214                         frame_size = cfg->packets_per_xact * sub_size;
 215                 }
 216                 break;
 217         default:
 218                 dev_warn(dev, "Query frame size of non-streaming channel\n");
 219                 frame_size = 0;
 220                 break;
 221         }
 222         return frame_size;
 223 }
 224
 225 /**
 226  * hdm_poison_channel - mark buffers of this channel as invalid
 227  * @iface: pointer to the interface
 228  * @channel: channel ID
 229  *
 230  * This unlinks all URBs submitted to the HCD,
 231  * calls the associated completion function of the core and removes
 232  * them from the list.
 233  *
 234  * Returns 0 on success or error code otherwise.
 235  */
 236 static int hdm_poison_channel(struct most_interface *iface, int channel)
 237 {
 238         struct most_dev *mdev = to_mdev(iface);
 239         unsigned long flags;
 240         spinlock_t *lock; /* temp. lock */
 241
 242         if (channel < 0 || channel >= iface->num_channels) {
 243                 dev_warn(&mdev->usb_device->dev, "Channel ID out of range.\n");
 244                 return -ECHRNG;
 245         }
 246
 247         lock = mdev->channel_lock + channel;
 248         spin_lock_irqsave(lock, flags);
 249         mdev->is_channel_healthy[channel] = false;
 250         spin_unlock_irqrestore(lock, flags);
 251
 252         cancel_work_sync(&mdev->clear_work[channel].ws);
 253
 254         mutex_lock(&mdev->io_mutex);
 255         usb_kill_anchored_urbs(&mdev->busy_urbs[channel]);
 256         if (mdev->padding_active[channel])
 257                 mdev->padding_active[channel] = false;
 258
 259         if (mdev->conf[channel].data_type == MOST_CH_ASYNC) {
 260                 del_timer_sync(&mdev->link_stat_timer);
 261                 cancel_work_sync(&mdev->poll_work_obj);
 262         }
 263         mutex_unlock(&mdev->io_mutex);
 264         return 0;
 265 }
 266
 267 /**
 268  * hdm_add_padding - add padding bytes
 269  * @mdev: most device
 270  * @channel: channel ID
 271  * @mbo: buffer object
 272  *
 273  * This inserts the INIC hardware specific padding bytes into a streaming
 274  * channel's buffer
 275  */
 276 static int hdm_add_padding(struct most_dev *mdev, int channel, struct mbo *mbo)
 277 {
 278         struct most_channel_config *conf = &mdev->conf[channel];
 279         unsigned int frame_size = get_stream_frame_size(&mdev->dev, conf);
 280         unsigned int j, num_frames;
 281
 282         if (!frame_size)
 283                 return -EINVAL;
 284         num_frames = mbo->buffer_length / frame_size;
 285
 286         if (num_frames < 1) {
 287                 dev_err(&mdev->usb_device->dev,
 288                         "Missed minimal transfer unit.\n");
 289                 return -EINVAL;
 290         }
 291
 292         for (j = num_frames - 1; j > 0; j--)
 293                 memmove(mbo->virt_address + j * USB_MTU,
 294                         mbo->virt_address + j * frame_size,
 295                         frame_size);
 296         mbo->buffer_length = num_frames * USB_MTU;
 297         return 0;
 298 }
 299
 300 /**
 301  * hdm_remove_padding - remove padding bytes
 302  * @mdev: most device
 303  * @channel: channel ID
 304  * @mbo: buffer object
 305  *
 306  * This takes the INIC hardware specific padding bytes off a streaming
 307  * channel's buffer.
 308  */
 309 static int hdm_remove_padding(struct most_dev *mdev, int channel,
 310                               struct mbo *mbo)
 311 {
 312         struct most_channel_config *const conf = &mdev->conf[channel];
 313         unsigned int frame_size = get_stream_frame_size(&mdev->dev, conf);
 314         unsigned int j, num_frames;
 315
 316         if (!frame_size)
 317                 return -EINVAL;
 318         num_frames = mbo->processed_length / USB_MTU;
 319
 320         for (j = 1; j < num_frames; j++)
 321                 memmove(mbo->virt_address + frame_size * j,
 322                         mbo->virt_address + USB_MTU * j,
 323                         frame_size);
 324
 325         mbo->processed_length = frame_size * num_frames;
 326         return 0;
 327 }
 328
 329 /**
 330  * hdm_write_completion - completion function for submitted Tx URBs
 331  * @urb: the URB that has been completed
 332  *
 333  * This checks the status of the completed URB. In case the URB has been
 334  * unlinked before, it is immediately freed. On any other error the MBO
 335  * transfer flag is set. On success it frees allocated resources and calls
 336  * the completion function.
 337  *
 338  * Context: interrupt!
 339  */
 340 static void hdm_write_completion(struct urb *urb)
 341 {
 342         struct mbo *mbo = urb->context;
 343         struct most_dev *mdev = to_mdev(mbo->ifp);
 344         unsigned int channel = mbo->hdm_channel_id;
 345         spinlock_t *lock = mdev->channel_lock + channel;
 346         unsigned long flags;
 347
 348         spin_lock_irqsave(lock, flags);
 349
 350         mbo->processed_length = 0;
 351         mbo->status = MBO_E_INVAL;
 352         if (likely(mdev->is_channel_healthy[channel])) {
 353                 switch (urb->status) {
 354                 case 0:
 355                 case -ESHUTDOWN:
 356                         mbo->processed_length = urb->actual_length;
 357                         mbo->status = MBO_SUCCESS;
 358                         break;
 359                 case -EPIPE:
 360                         dev_warn(&mdev->usb_device->dev,
 361                                  "Broken pipe on ep%02x\n",
 362                                  mdev->ep_address[channel]);
 363                         mdev->is_channel_healthy[channel] = false;
 364                         mdev->clear_work[channel].pipe = urb->pipe;
 365                         schedule_work(&mdev->clear_work[channel].ws);
 366                         break;
 367                 case -ENODEV:
 368                 case -EPROTO:
 369                         mbo->status = MBO_E_CLOSE;
 370                         break;
 371                 }
 372         }
 373
 374         spin_unlock_irqrestore(lock, flags);
 375
 376         if (likely(mbo->complete))
 377                 mbo->complete(mbo);
 378         usb_free_urb(urb);
 379 }
 380
 381 /**
 382  * hdm_read_completion - completion function for submitted Rx URBs
 383  * @urb: the URB that has been completed
 384  *
 385  * This checks the status of the completed URB. In case the URB has been
 386  * unlinked before it is immediately freed. On any other error the MBO transfer
 387  * flag is set. On success it frees allocated resources, removes
 388  * padding bytes -if necessary- and calls the completion function.
 389  *
 390  * Context: interrupt!
 391  */
 392 static void hdm_read_completion(struct urb *urb)
 393 {
 394         struct mbo *mbo = urb->context;
 395         struct most_dev *mdev = to_mdev(mbo->ifp);
 396         unsigned int channel = mbo->hdm_channel_id;
 397         struct device *dev = &mdev->usb_device->dev;
 398         spinlock_t *lock = mdev->channel_lock + channel;
 399         unsigned long flags;
 400
 401         spin_lock_irqsave(lock, flags);
 402
 403         mbo->processed_length = 0;
 404         mbo->status = MBO_E_INVAL;
 405         if (likely(mdev->is_channel_healthy[channel])) {
 406                 switch (urb->status) {
 407                 case 0:
 408                 case -ESHUTDOWN:
 409                         mbo->processed_length = urb->actual_length;
 410                         mbo->status = MBO_SUCCESS;
 411                         if (mdev->padding_active[channel] &&
 412                             hdm_remove_padding(mdev, channel, mbo)) {
 413                                 mbo->processed_length = 0;
 414                                 mbo->status = MBO_E_INVAL;
 415                         }
 416                         break;
 417                 case -EPIPE:
 418                         dev_warn(dev, "Broken pipe on ep%02x\n",
 419                                  mdev->ep_address[channel]);
 420                         mdev->is_channel_healthy[channel] = false;
 421                         mdev->clear_work[channel].pipe = urb->pipe;
 422                         schedule_work(&mdev->clear_work[channel].ws);
 423                         break;
 424                 case -ENODEV:
 425                 case -EPROTO:
 426                         mbo->status = MBO_E_CLOSE;
 427                         break;
 428                 case -EOVERFLOW:
 429                         dev_warn(dev, "Babble on ep%02x\n",
 430                                  mdev->ep_address[channel]);
 431                         break;
 432                 }
 433         }
 434
 435         spin_unlock_irqrestore(lock, flags);
 436
 437         if (likely(mbo->complete))
 438                 mbo->complete(mbo);
 439         usb_free_urb(urb);
 440 }
 441
 442 /**
 443  * hdm_enqueue - receive a buffer to be used for data transfer
 444  * @iface: interface to enqueue to
 445  * @channel: ID of the channel
 446  * @mbo: pointer to the buffer object
 447  *
 448  * This allocates a new URB and fills it according to the channel
 449  * that is being used for transmission of data. Before the URB is
 450  * submitted it is stored in the private anchor list.
 451  *
 452  * Returns 0 on success. On any error the URB is freed and a error code
 453  * is returned.
 454  *
 455  * Context: Could in _some_ cases be interrupt!
 456  */
 457 static int hdm_enqueue(struct most_interface *iface, int channel,
 458                        struct mbo *mbo)
 459 {
 460         struct most_dev *mdev = to_mdev(iface);
 461         struct most_channel_config *conf;
 462         int retval = 0;
 463         struct urb *urb;
 464         unsigned long length;
 465         void *virt_address;
 466
 467         if (!mbo)
 468                 return -EINVAL;
 469         if (iface->num_channels <= channel || channel < 0)
 470                 return -ECHRNG;
 471
 472         urb = usb_alloc_urb(NO_ISOCHRONOUS_URB, GFP_KERNEL);
 473         if (!urb)
 474                 return -ENOMEM;
 475
 476         conf = &mdev->conf[channel];
 477
 478         mutex_lock(&mdev->io_mutex);
 479         if (!mdev->usb_device) {
 480                 retval = -ENODEV;
 481                 goto err_free_urb;
 482         }
 483
 484         if ((conf->direction & MOST_CH_TX) && mdev->padding_active[channel] &&
 485             hdm_add_padding(mdev, channel, mbo)) {
 486                 retval = -EINVAL;
 487                 goto err_free_urb;
 488         }
 489
 490         urb->transfer_dma = mbo->bus_address;
 491         virt_address = mbo->virt_address;
 492         length = mbo->buffer_length;
 493
 494         if (conf->direction & MOST_CH_TX) {
 495                 usb_fill_bulk_urb(urb, mdev->usb_device,
 496                                   usb_sndbulkpipe(mdev->usb_device,
 497                                                   mdev->ep_address[channel]),
 498                                   virt_address,
 499                                   length,
 500                                   hdm_write_completion,
 501                                   mbo);
 502                 if (conf->data_type != MOST_CH_ISOC &&
 503                     conf->data_type != MOST_CH_SYNC)
 504                         urb->transfer_flags |= URB_ZERO_PACKET;
 505         } else {
 506                 usb_fill_bulk_urb(urb, mdev->usb_device,
 507                                   usb_rcvbulkpipe(mdev->usb_device,
 508                                                   mdev->ep_address[channel]),
 509                                   virt_address,
 510                                   length + conf->extra_len,
 511                                   hdm_read_completion,
 512                                   mbo);
 513         }
 514         urb->transfer_flags |= URB_NO_TRANSFER_DMA_MAP;
 515
 516         usb_anchor_urb(urb, &mdev->busy_urbs[channel]);
 517
 518         retval = usb_submit_urb(urb, GFP_KERNEL);
 519         if (retval) {
 520                 dev_err(&mdev->usb_device->dev,
 521                         "URB submit failed with error %d.\n", retval);
 522                 goto err_unanchor_urb;
 523         }
 524         mutex_unlock(&mdev->io_mutex);
 525         return 0;
 526
 527 err_unanchor_urb:
 528         usb_unanchor_urb(urb);
 529 err_free_urb:
 530         usb_free_urb(urb);
 531         mutex_unlock(&mdev->io_mutex);
 532         return retval;
 533 }
 534
 535 static void *hdm_dma_alloc(struct mbo *mbo, u32 size)
 536 {
 537         struct most_dev *mdev = to_mdev(mbo->ifp);
 538
 539         return usb_alloc_coherent(mdev->usb_device, size, GFP_KERNEL,
 540                                   &mbo->bus_address);
 541 }
 542
 543 static void hdm_dma_free(struct mbo *mbo, u32 size)
 544 {
 545         struct most_dev *mdev = to_mdev(mbo->ifp);
 546
 547         usb_free_coherent(mdev->usb_device, size, mbo->virt_address,
 548                           mbo->bus_address);
 549 }
 550
 551 /**
 552  * hdm_configure_channel - receive channel configuration from core
 553  * @iface: interface
 554  * @channel: channel ID
 555  * @conf: structure that holds the configuration information
 556  *
 557  * The attached network interface controller (NIC) supports a padding mode
 558  * to avoid short packets on USB, hence increasing the performance due to a
 559  * lower interrupt load. This mode is default for synchronous data and can
 560  * be switched on for isochronous data. In case padding is active the
 561  * driver needs to know the frame size of the payload in order to calculate
 562  * the number of bytes it needs to pad when transmitting or to cut off when
 563  * receiving data.
 564  *
 565  */
 566 static int hdm_configure_channel(struct most_interface *iface, int channel,
 567                                  struct most_channel_config *conf)
 568 {
 569         unsigned int num_frames;
 570         unsigned int frame_size;
 571         struct most_dev *mdev = to_mdev(iface);
 572         struct device *dev = &mdev->usb_device->dev;
 573
 574         if (!conf) {
 575                 dev_err(dev, "Bad config pointer.\n");
 576                 return -EINVAL;
 577         }
 578         if (channel < 0 || channel >= iface->num_channels) {
 579                 dev_err(dev, "Channel ID out of range.\n");
 580                 return -EINVAL;
 581         }
 582
 583         mdev->is_channel_healthy[channel] = true;
 584         mdev->clear_work[channel].channel = channel;
 585         mdev->clear_work[channel].mdev = mdev;
 586         INIT_WORK(&mdev->clear_work[channel].ws, wq_clear_halt);
 587
 588         if (!conf->num_buffers || !conf->buffer_size) {
 589                 dev_err(dev, "Misconfig: buffer size or #buffers zero.\n");
 590                 return -EINVAL;
 591         }
 592
 593         if (conf->data_type != MOST_CH_SYNC &&
 594             !(conf->data_type == MOST_CH_ISOC &&
 595               conf->packets_per_xact != 0xFF)) {
 596                 mdev->padding_active[channel] = false;
 597                 /*
 598                  * Since the NIC's padding mode is not going to be
 599                  * used, we can skip the frame size calculations and
 600                  * move directly on to exit.
 601                  */
 602                 goto exit;
 603         }
 604
 605         mdev->padding_active[channel] = true;
 606
 607         frame_size = get_stream_frame_size(&mdev->dev, conf);
 608         if (frame_size == 0 || frame_size > USB_MTU) {
 609                 dev_warn(dev, "Misconfig: frame size wrong\n");
 610                 return -EINVAL;
 611         }
 612
 613         num_frames = conf->buffer_size / frame_size;
 614
 615         if (conf->buffer_size % frame_size) {
 616                 u16 old_size = conf->buffer_size;
 617
 618                 conf->buffer_size = num_frames * frame_size;
 619                 dev_warn(dev, "%s: fixed buffer size (%d -> %d)\n",
 620                          mdev->suffix[channel], old_size, conf->buffer_size);
 621         }
 622
 623         /* calculate extra length to comply w/ HW padding */
 624         conf->extra_len = num_frames * (USB_MTU - frame_size);
 625
 626 exit:
 627         mdev->conf[channel] = *conf;
 628         if (conf->data_type == MOST_CH_ASYNC) {
 629                 u16 ep = mdev->ep_address[channel];
 630
 631                 if (start_sync_ep(mdev->usb_device, ep) < 0)
 632                         dev_warn(dev, "sync for ep%02x failed", ep);
 633         }
 634         return 0;
 635 }
 636
 637 /**
 638  * hdm_request_netinfo - request network information
 639  * @iface: pointer to interface
 640  * @channel: channel ID
 641  *
 642  * This is used as trigger to set up the link status timer that
 643  * polls for the NI state of the INIC every 2 seconds.
 644  *
 645  */
 646 static void hdm_request_netinfo(struct most_interface *iface, int channel,
 647                                 void (*on_netinfo)(struct most_interface *,
 648                                                    unsigned char,
 649                                                    unsigned char *))
 650 {
 651         struct most_dev *mdev = to_mdev(iface);
 652
 653         mdev->on_netinfo = on_netinfo;
 654         if (!on_netinfo)
 655                 return;
 656
 657         mdev->link_stat_timer.expires = jiffies + HZ;
 658         mod_timer(&mdev->link_stat_timer, mdev->link_stat_timer.expires);
 659 }
 660
 661 /**
 662  * link_stat_timer_handler - schedule work obtaining mac address and link status
 663  * @data: pointer to USB device instance
 664  *
 665  * The handler runs in interrupt context. That's why we need to defer the
 666  * tasks to a work queue.
 667  */
 668 static void link_stat_timer_handler(struct timer_list *t)
 669 {
 670         struct most_dev *mdev = from_timer(mdev, t, link_stat_timer);
 671
 672         schedule_work(&mdev->poll_work_obj);
 673         mdev->link_stat_timer.expires = jiffies + (2 * HZ);
 674         add_timer(&mdev->link_stat_timer);
 675 }
 676
 677 /**
 678  * wq_netinfo - work queue function to deliver latest networking information
 679  * @wq_obj: object that holds data for our deferred work to do
 680  *
 681  * This retrieves the network interface status of the USB INIC
 682  */
 683 static void wq_netinfo(struct work_struct *wq_obj)
 684 {
 685         struct most_dev *mdev = to_mdev_from_work(wq_obj);
 686         struct usb_device *usb_device = mdev->usb_device;
 687         struct device *dev = &usb_device->dev;
 688         u16 hi, mi, lo, link;
 689         u8 hw_addr[6];
 690
 691         if (drci_rd_reg(usb_device, DRCI_REG_HW_ADDR_HI, &hi)) {
 692                 dev_err(dev, "Vendor request 'hw_addr_hi' failed\n");
 693                 return;
 694         }
 695
 696         if (drci_rd_reg(usb_device, DRCI_REG_HW_ADDR_MI, &mi)) {
 697                 dev_err(dev, "Vendor request 'hw_addr_mid' failed\n");
 698                 return;
 699         }
 700
 701         if (drci_rd_reg(usb_device, DRCI_REG_HW_ADDR_LO, &lo)) {
 702                 dev_err(dev, "Vendor request 'hw_addr_low' failed\n");
 703                 return;
 704         }
 705
 706         if (drci_rd_reg(usb_device, DRCI_REG_NI_STATE, &link)) {
 707                 dev_err(dev, "Vendor request 'link status' failed\n");
 708                 return;
 709         }
 710
 711         hw_addr[0] = hi >> 8;
 712         hw_addr[1] = hi;
 713         hw_addr[2] = mi >> 8;
 714         hw_addr[3] = mi;
 715         hw_addr[4] = lo >> 8;
 716         hw_addr[5] = lo;
 717
 718         if (mdev->on_netinfo)
 719                 mdev->on_netinfo(&mdev->iface, link, hw_addr);
 720 }
 721
 722 /**
 723  * wq_clear_halt - work queue function
 724  * @wq_obj: work_struct object to execute
 725  *
 726  * This sends a clear_halt to the given USB pipe.
 727  */
 728 static void wq_clear_halt(struct work_struct *wq_obj)
 729 {
 730         struct clear_hold_work *clear_work = to_clear_hold_work(wq_obj);
 731         struct most_dev *mdev = clear_work->mdev;
 732         unsigned int channel = clear_work->channel;
 733         int pipe = clear_work->pipe;
 734         int snd_pipe;
 735         int peer;
 736
 737         mutex_lock(&mdev->io_mutex);
 738         most_stop_enqueue(&mdev->iface, channel);
 739         usb_kill_anchored_urbs(&mdev->busy_urbs[channel]);
 740         if (usb_clear_halt(mdev->usb_device, pipe))
 741                 dev_warn(&mdev->usb_device->dev, "Failed to reset endpoint.\n");
 742
 743         /* If the functional Stall condition has been set on an
 744          * asynchronous rx channel, we need to clear the tx channel
 745          * too, since the hardware runs its clean-up sequence on both
 746          * channels, as they are physically one on the network.
 747          *
 748          * The USB interface that exposes the asynchronous channels
 749          * contains always two endpoints, and two only.
 750          */
 751         if (mdev->conf[channel].data_type == MOST_CH_ASYNC &&
 752             mdev->conf[channel].direction == MOST_CH_RX) {
 753                 if (channel == 0)
 754                         peer = 1;
 755                 else
 756                         peer = 0;
 757                 snd_pipe = usb_sndbulkpipe(mdev->usb_device,
 758                                            mdev->ep_address[peer]);
 759                 usb_clear_halt(mdev->usb_device, snd_pipe);
 760         }
 761         mdev->is_channel_healthy[channel] = true;
 762         most_resume_enqueue(&mdev->iface, channel);
 763         mutex_unlock(&mdev->io_mutex);
 764 }
 765
 766 /**
 767  * hdm_usb_fops - file operation table for USB driver
 768  */
 769 static const struct file_operations hdm_usb_fops = {
 770         .owner = THIS_MODULE,
 771 };
 772
 773 /**
 774  * usb_device_id - ID table for HCD device probing
 775  */
 776 static const struct usb_device_id usbid[] = {
 777         { USB_DEVICE(USB_VENDOR_ID_SMSC, USB_DEV_ID_BRDG), },
 778         { USB_DEVICE(USB_VENDOR_ID_SMSC, USB_DEV_ID_OS81118), },
 779         { USB_DEVICE(USB_VENDOR_ID_SMSC, USB_DEV_ID_OS81119), },
 780         { USB_DEVICE(USB_VENDOR_ID_SMSC, USB_DEV_ID_OS81210), },
 781         { } /* Terminating entry */
 782 };
 783
 784 struct regs {
 785         const char *name;
 786         u16 reg;
 787 };
 788
 789 static const struct regs ro_regs[] = {
 790         { "ni_state", DRCI_REG_NI_STATE },
 791         { "packet_bandwidth", DRCI_REG_PACKET_BW },
 792         { "node_address", DRCI_REG_NODE_ADDR },
 793         { "node_position", DRCI_REG_NODE_POS },
 794 };
 795
 796 static const struct regs rw_regs[] = {
 797         { "mep_filter", DRCI_REG_MEP_FILTER },
 798         { "mep_hash0", DRCI_REG_HASH_TBL0 },
 799         { "mep_hash1", DRCI_REG_HASH_TBL1 },
 800         { "mep_hash2", DRCI_REG_HASH_TBL2 },
 801         { "mep_hash3", DRCI_REG_HASH_TBL3 },
 802         { "mep_eui48_hi", DRCI_REG_HW_ADDR_HI },
 803         { "mep_eui48_mi", DRCI_REG_HW_ADDR_MI },
 804         { "mep_eui48_lo", DRCI_REG_HW_ADDR_LO },
 805 };
 806
 807 static int get_stat_reg_addr(const struct regs *regs, int size,
 808                              const char *name, u16 *reg_addr)
 809 {
 810         int i;
 811
 812         for (i = 0; i < size; i++) {
 813                 if (sysfs_streq(name, regs[i].name)) {
 814                         *reg_addr = regs[i].reg;
 815                         return 0;
 816                 }
 817         }
 818         return -EINVAL;
 819 }
 820
 821 #define get_static_reg_addr(regs, name, reg_addr) \
 822         get_stat_reg_addr(regs, ARRAY_SIZE(regs), name, reg_addr)
 823
 824 static ssize_t value_show(struct device *dev, struct device_attribute *attr,
 825                           char *buf)
 826 {
 827         const char *name = attr->attr.name;
 828         struct most_dci_obj *dci_obj = to_dci_obj(dev);
 829         u16 val;
 830         u16 reg_addr;
 831         int err;
 832
 833         if (sysfs_streq(name, "arb_address"))
 834                 return snprintf(buf, PAGE_SIZE, "%04x\n", dci_obj->reg_addr);
 835
 836         if (sysfs_streq(name, "arb_value"))
 837                 reg_addr = dci_obj->reg_addr;
 838         else if (get_static_reg_addr(ro_regs, name, &reg_addr) &&
 839                  get_static_reg_addr(rw_regs, name, &reg_addr))
 840                 return -EINVAL;
 841
 842         err = drci_rd_reg(dci_obj->usb_device, reg_addr, &val);
 843         if (err < 0)
 844                 return err;
 845
 846         return snprintf(buf, PAGE_SIZE, "%04x\n", val);
 847 }
 848
 849 static ssize_t value_store(struct device *dev, struct device_attribute *attr,
 850                            const char *buf, size_t count)
 851 {
 852         u16 val;
 853         u16 reg_addr;
 854         const char *name = attr->attr.name;
 855         struct most_dci_obj *dci_obj = to_dci_obj(dev);
 856         struct usb_device *usb_dev = dci_obj->usb_device;
 857         int err;
 858
 859         err = kstrtou16(buf, 16, &val);
 860         if (err)
 861                 return err;
 862
 863         if (sysfs_streq(name, "arb_address")) {
 864                 dci_obj->reg_addr = val;
 865                 return count;
 866         }
 867
 868         if (sysfs_streq(name, "arb_value"))
 869                 err = drci_wr_reg(usb_dev, dci_obj->reg_addr, val);
 870         else if (sysfs_streq(name, "sync_ep"))
 871                 err = start_sync_ep(usb_dev, val);
 872         else if (!get_static_reg_addr(rw_regs, name, &reg_addr))
 873                 err = drci_wr_reg(usb_dev, reg_addr, val);
 874         else
 875                 return -EINVAL;
 876
 877         if (err < 0)
 878                 return err;
 879
 880         return count;
 881 }
 882
 883 static DEVICE_ATTR(ni_state, 0444, value_show, NULL);
 884 static DEVICE_ATTR(packet_bandwidth, 0444, value_show, NULL);
 885 static DEVICE_ATTR(node_address, 0444, value_show, NULL);
 886 static DEVICE_ATTR(node_position, 0444, value_show, NULL);
 887 static DEVICE_ATTR(sync_ep, 0200, NULL, value_store);
 888 static DEVICE_ATTR(mep_filter, 0644, value_show, value_store);
 889 static DEVICE_ATTR(mep_hash0, 0644, value_show, value_store);
 890 static DEVICE_ATTR(mep_hash1, 0644, value_show, value_store);
 891 static DEVICE_ATTR(mep_hash2, 0644, value_show, value_store);
 892 static DEVICE_ATTR(mep_hash3, 0644, value_show, value_store);
 893 static DEVICE_ATTR(mep_eui48_hi, 0644, value_show, value_store);
 894 static DEVICE_ATTR(mep_eui48_mi, 0644, value_show, value_store);
 895 static DEVICE_ATTR(mep_eui48_lo, 0644, value_show, value_store);
 896 static DEVICE_ATTR(arb_address, 0644, value_show, value_store);
 897 static DEVICE_ATTR(arb_value, 0644, value_show, value_store);
 898
 899 static struct attribute *dci_attrs[] = {
 900         &dev_attr_ni_state.attr,
 901         &dev_attr_packet_bandwidth.attr,
 902         &dev_attr_node_address.attr,
 903         &dev_attr_node_position.attr,
 904         &dev_attr_sync_ep.attr,
 905         &dev_attr_mep_filter.attr,
 906         &dev_attr_mep_hash0.attr,
 907         &dev_attr_mep_hash1.attr,
 908         &dev_attr_mep_hash2.attr,
 909         &dev_attr_mep_hash3.attr,
 910         &dev_attr_mep_eui48_hi.attr,
 911         &dev_attr_mep_eui48_mi.attr,
 912         &dev_attr_mep_eui48_lo.attr,
 913         &dev_attr_arb_address.attr,
 914         &dev_attr_arb_value.attr,
 915         NULL,
 916 };
 917
 918 ATTRIBUTE_GROUPS(dci);
 919
 920 static void release_dci(struct device *dev)
 921 {
 922         struct most_dci_obj *dci = to_dci_obj(dev);
 923
 924         put_device(dev->parent);
 925         kfree(dci);
 926 }
 927
 928 static void release_mdev(struct device *dev)
 929 {
 930         struct most_dev *mdev = to_mdev_from_dev(dev);
 931
 932         kfree(mdev);
 933 }
 934 /**
 935  * hdm_probe - probe function of USB device driver
 936  * @interface: Interface of the attached USB device
 937  * @id: Pointer to the USB ID table.
 938  *
 939  * This allocates and initializes the device instance, adds the new
 940  * entry to the internal list, scans the USB descriptors and registers
 941  * the interface with the core.
 942  * Additionally, the DCI objects are created and the hardware is sync'd.
 943  *
 944  * Return 0 on success. In case of an error a negative number is returned.
 945  */
 946 static int
 947 hdm_probe(struct usb_interface *interface, const struct usb_device_id *id)
 948 {
 949         struct usb_host_interface *usb_iface_desc = interface->cur_altsetting;
 950         struct usb_device *usb_dev = interface_to_usbdev(interface);
 951         struct device *dev = &usb_dev->dev;
 952         struct most_dev *mdev;
 953         unsigned int i;
 954         unsigned int num_endpoints;
 955         struct most_channel_capability *tmp_cap;
 956         struct usb_endpoint_descriptor *ep_desc;
 957         int ret = -ENOMEM;
 958
 959         mdev = kzalloc(sizeof(*mdev), GFP_KERNEL);
 960         if (!mdev)
 961                 return -ENOMEM;
 962
 963         usb_set_intfdata(interface, mdev);
 964         num_endpoints = usb_iface_desc->desc.bNumEndpoints;
 965         if (num_endpoints > MAX_NUM_ENDPOINTS) {
 966                 kfree(mdev);
 967                 return -EINVAL;
 968         }
 969         mutex_init(&mdev->io_mutex);
 970         INIT_WORK(&mdev->poll_work_obj, wq_netinfo);
 971         timer_setup(&mdev->link_stat_timer, link_stat_timer_handler, 0);
 972
 973         mdev->usb_device = usb_dev;
 974         mdev->link_stat_timer.expires = jiffies + (2 * HZ);
 975
 976         mdev->iface.mod = hdm_usb_fops.owner;
 977         mdev->iface.dev = &mdev->dev;
 978         mdev->iface.driver_dev = &interface->dev;
 979         mdev->iface.interface = ITYPE_USB;
 980         mdev->iface.configure = hdm_configure_channel;
 981         mdev->iface.request_netinfo = hdm_request_netinfo;
 982         mdev->iface.enqueue = hdm_enqueue;
 983         mdev->iface.poison_channel = hdm_poison_channel;
 984         mdev->iface.dma_alloc = hdm_dma_alloc;
 985         mdev->iface.dma_free = hdm_dma_free;
 986         mdev->iface.description = mdev->description;
 987         mdev->iface.num_channels = num_endpoints;
 988
 989         snprintf(mdev->description, sizeof(mdev->description),
 990                  "%d-%s:%d.%d",
 991                  usb_dev->bus->busnum,
 992                  usb_dev->devpath,
 993                  usb_dev->config->desc.bConfigurationValue,
 994                  usb_iface_desc->desc.bInterfaceNumber);
 995
 996         mdev->dev.init_name = mdev->description;
 997         mdev->dev.parent = &interface->dev;
 998         mdev->dev.release = release_mdev;
 999         mdev->conf = kcalloc(num_endpoints, sizeof(*mdev->conf), GFP_KERNEL);
1000         if (!mdev->conf)
1001                 goto err_free_mdev;
1002
1003         mdev->cap = kcalloc(num_endpoints, sizeof(*mdev->cap), GFP_KERNEL);
1004         if (!mdev->cap)
1005                 goto err_free_conf;
1006
1007         mdev->iface.channel_vector = mdev->cap;
1008         mdev->ep_address =
1009                 kcalloc(num_endpoints, sizeof(*mdev->ep_address), GFP_KERNEL);
1010         if (!mdev->ep_address)
1011                 goto err_free_cap;
1012
1013         mdev->busy_urbs =
1014                 kcalloc(num_endpoints, sizeof(*mdev->busy_urbs), GFP_KERNEL);
1015         if (!mdev->busy_urbs)
1016                 goto err_free_ep_address;
1017
1018         tmp_cap = mdev->cap;
1019         for (i = 0; i < num_endpoints; i++) {
1020                 ep_desc = &usb_iface_desc->endpoint[i].desc;
1021                 mdev->ep_address[i] = ep_desc->bEndpointAddress;
1022                 mdev->padding_active[i] = false;
1023                 mdev->is_channel_healthy[i] = true;
1024
1025                 snprintf(&mdev->suffix[i][0], MAX_SUFFIX_LEN, "ep%02x",
1026                          mdev->ep_address[i]);
1027
1028                 tmp_cap->name_suffix = &mdev->suffix[i][0];
1029                 tmp_cap->buffer_size_packet = MAX_BUF_SIZE;
1030                 tmp_cap->buffer_size_streaming = MAX_BUF_SIZE;
1031                 tmp_cap->num_buffers_packet = BUF_CHAIN_SIZE;
1032                 tmp_cap->num_buffers_streaming = BUF_CHAIN_SIZE;
1033                 tmp_cap->data_type = MOST_CH_CONTROL | MOST_CH_ASYNC |
1034                                      MOST_CH_ISOC | MOST_CH_SYNC;
1035                 if (usb_endpoint_dir_in(ep_desc))
1036                         tmp_cap->direction = MOST_CH_RX;
1037                 else
1038                         tmp_cap->direction = MOST_CH_TX;
1039                 tmp_cap++;
1040                 init_usb_anchor(&mdev->busy_urbs[i]);
1041                 spin_lock_init(&mdev->channel_lock[i]);
1042         }
1043         dev_dbg(dev, "claimed gadget: Vendor=%4.4x ProdID=%4.4x Bus=%02x Device=%02x\n",
1044                 le16_to_cpu(usb_dev->descriptor.idVendor),
1045                 le16_to_cpu(usb_dev->descriptor.idProduct),
1046                 usb_dev->bus->busnum,
1047                 usb_dev->devnum);
1048
1049         dev_dbg(dev, "device path: /sys/bus/usb/devices/%d-%s:%d.%d\n",
1050                 usb_dev->bus->busnum,
1051                 usb_dev->devpath,
1052                 usb_dev->config->desc.bConfigurationValue,
1053                 usb_iface_desc->desc.bInterfaceNumber);
1054
1055         ret = most_register_interface(&mdev->iface);
1056         if (ret)
1057                 goto err_free_busy_urbs;
1058
1059         mutex_lock(&mdev->io_mutex);
1060         if (le16_to_cpu(usb_dev->descriptor.idProduct) == USB_DEV_ID_OS81118 ||
1061             le16_to_cpu(usb_dev->descriptor.idProduct) == USB_DEV_ID_OS81119 ||
1062             le16_to_cpu(usb_dev->descriptor.idProduct) == USB_DEV_ID_OS81210) {
1063                 mdev->dci = kzalloc(sizeof(*mdev->dci), GFP_KERNEL);
1064                 if (!mdev->dci) {
1065                         mutex_unlock(&mdev->io_mutex);
1066                         most_deregister_interface(&mdev->iface);
1067                         ret = -ENOMEM;
1068                         goto err_free_busy_urbs;
1069                 }
1070
1071                 mdev->dci->dev.init_name = "dci";
1072                 mdev->dci->dev.parent = get_device(mdev->iface.dev);
1073                 mdev->dci->dev.groups = dci_groups;
1074                 mdev->dci->dev.release = release_dci;
1075                 if (device_register(&mdev->dci->dev)) {
1076                         mutex_unlock(&mdev->io_mutex);
1077                         most_deregister_interface(&mdev->iface);
1078                         ret = -ENOMEM;
1079                         goto err_free_dci;
1080                 }
1081                 mdev->dci->usb_device = mdev->usb_device;
1082         }
1083         mutex_unlock(&mdev->io_mutex);
1084         return 0;
1085 err_free_dci:
1086         put_device(&mdev->dci->dev);
1087 err_free_busy_urbs:
1088         kfree(mdev->busy_urbs);
1089 err_free_ep_address:
1090         kfree(mdev->ep_address);
1091 err_free_cap:
1092         kfree(mdev->cap);
1093 err_free_conf:
1094         kfree(mdev->conf);
1095 err_free_mdev:
1096         put_device(&mdev->dev);
1097         return ret;
1098 }
1099
1100 /**
1101  * hdm_disconnect - disconnect function of USB device driver
1102  * @interface: Interface of the attached USB device
1103  *
1104  * This deregisters the interface with the core, removes the kernel timer
1105  * and frees resources.
1106  *
1107  * Context: hub kernel thread
1108  */
1109 static void hdm_disconnect(struct usb_interface *interface)
1110 {
1111         struct most_dev *mdev = usb_get_intfdata(interface);
1112
1113         mutex_lock(&mdev->io_mutex);
1114         usb_set_intfdata(interface, NULL);
1115         mdev->usb_device = NULL;
1116         mutex_unlock(&mdev->io_mutex);
1117
1118         del_timer_sync(&mdev->link_stat_timer);
1119         cancel_work_sync(&mdev->poll_work_obj);
1120
1121         if (mdev->dci)
1122                 device_unregister(&mdev->dci->dev);
1123         most_deregister_interface(&mdev->iface);
1124
1125         kfree(mdev->busy_urbs);
1126         kfree(mdev->cap);
1127         kfree(mdev->conf);
1128         kfree(mdev->ep_address);
1129         put_device(&mdev->dci->dev);
1130         put_device(&mdev->dev);
1131 }
1132
1133 static int hdm_suspend(struct usb_interface *interface, pm_message_t message)
1134 {
1135         struct most_dev *mdev = usb_get_intfdata(interface);
1136         int i;
1137
1138         mutex_lock(&mdev->io_mutex);
1139         for (i = 0; i < mdev->iface.num_channels; i++) {
1140                 most_stop_enqueue(&mdev->iface, i);
1141                 usb_kill_anchored_urbs(&mdev->busy_urbs[i]);
1142         }
1143         mutex_unlock(&mdev->io_mutex);
1144         return 0;
1145 }
1146
1147 static int hdm_resume(struct usb_interface *interface)
1148 {
1149         struct most_dev *mdev = usb_get_intfdata(interface);
1150         int i;
1151
1152         mutex_lock(&mdev->io_mutex);
1153         for (i = 0; i < mdev->iface.num_channels; i++)
1154                 most_resume_enqueue(&mdev->iface, i);
1155         mutex_unlock(&mdev->io_mutex);
1156         return 0;
1157 }
1158
1159 static struct usb_driver hdm_usb = {
1160         .name = "hdm_usb",
1161         .id_table = usbid,
1162         .probe = hdm_probe,
1163         .disconnect = hdm_disconnect,
1164         .resume = hdm_resume,
1165         .suspend = hdm_suspend,
1166 };
1167
1168 module_usb_driver(hdm_usb);
1169 MODULE_LICENSE("GPL");
1170 MODULE_AUTHOR("Christian Gromm <christian.gromm@microchip.com>");
1171 MODULE_DESCRIPTION("HDM_4_USB");