drivers/mmc/host/sdhci.c

   1 // SPDX-License-Identifier: GPL-2.0-or-later
   2 /*
   3  *  linux/drivers/mmc/host/sdhci.c - Secure Digital Host Controller Interface driver
   4  *
   5  *  Copyright (C) 2005-2008 Pierre Ossman, All Rights Reserved.
   6  *
   7  * Thanks to the following companies for their support:
   8  *
   9  *     - JMicron (hardware and technical support)
  10  */
  11
  12 #include <linux/bitfield.h>
  13 #include <linux/delay.h>
  14 #include <linux/dmaengine.h>
  15 #include <linux/ktime.h>
  16 #include <linux/highmem.h>
  17 #include <linux/io.h>
  18 #include <linux/module.h>
  19 #include <linux/dma-mapping.h>
  20 #include <linux/slab.h>
  21 #include <linux/scatterlist.h>
  22 #include <linux/sizes.h>
  23 #include <linux/regulator/consumer.h>
  24 #include <linux/pm_runtime.h>
  25 #include <linux/of.h>
  26
  27 #include <linux/leds.h>
  28
  29 #include <linux/mmc/mmc.h>
  30 #include <linux/mmc/host.h>
  31 #include <linux/mmc/card.h>
  32 #include <linux/mmc/sdio.h>
  33 #include <linux/mmc/slot-gpio.h>
  34
  35 #include "sdhci.h"
  36
  37 #define DRIVER_NAME "sdhci"
  38
  39 #define DBG(f, x...) \
  40         pr_debug("%s: " DRIVER_NAME ": " f, mmc_hostname(host->mmc), ## x)
  41
  42 #define SDHCI_DUMP(f, x...) \
  43         pr_err("%s: " DRIVER_NAME ": " f, mmc_hostname(host->mmc), ## x)
  44
  45 #define MAX_TUNING_LOOP 40
  46
  47 static unsigned int debug_quirks = 0;
  48 static unsigned int debug_quirks2;
  49
  50 static void sdhci_enable_preset_value(struct sdhci_host *host, bool enable);
  51
  52 static bool sdhci_send_command(struct sdhci_host *host, struct mmc_command *cmd);
  53
  54 void sdhci_dumpregs(struct sdhci_host *host)
  55 {
  56         SDHCI_DUMP("============ SDHCI REGISTER DUMP ===========\n");
  57
  58         SDHCI_DUMP("Sys addr:  0x%08x | Version:  0x%08x\n",
  59                    sdhci_readl(host, SDHCI_DMA_ADDRESS),
  60                    sdhci_readw(host, SDHCI_HOST_VERSION));
  61         SDHCI_DUMP("Blk size:  0x%08x | Blk cnt:  0x%08x\n",
  62                    sdhci_readw(host, SDHCI_BLOCK_SIZE),
  63                    sdhci_readw(host, SDHCI_BLOCK_COUNT));
  64         SDHCI_DUMP("Argument:  0x%08x | Trn mode: 0x%08x\n",
  65                    sdhci_readl(host, SDHCI_ARGUMENT),
  66                    sdhci_readw(host, SDHCI_TRANSFER_MODE));
  67         SDHCI_DUMP("Present:   0x%08x | Host ctl: 0x%08x\n",
  68                    sdhci_readl(host, SDHCI_PRESENT_STATE),
  69                    sdhci_readb(host, SDHCI_HOST_CONTROL));
  70         SDHCI_DUMP("Power:     0x%08x | Blk gap:  0x%08x\n",
  71                    sdhci_readb(host, SDHCI_POWER_CONTROL),
  72                    sdhci_readb(host, SDHCI_BLOCK_GAP_CONTROL));
  73         SDHCI_DUMP("Wake-up:   0x%08x | Clock:    0x%08x\n",
  74                    sdhci_readb(host, SDHCI_WAKE_UP_CONTROL),
  75                    sdhci_readw(host, SDHCI_CLOCK_CONTROL));
  76         SDHCI_DUMP("Timeout:   0x%08x | Int stat: 0x%08x\n",
  77                    sdhci_readb(host, SDHCI_TIMEOUT_CONTROL),
  78                    sdhci_readl(host, SDHCI_INT_STATUS));
  79         SDHCI_DUMP("Int enab:  0x%08x | Sig enab: 0x%08x\n",
  80                    sdhci_readl(host, SDHCI_INT_ENABLE),
  81                    sdhci_readl(host, SDHCI_SIGNAL_ENABLE));
  82         SDHCI_DUMP("ACmd stat: 0x%08x | Slot int: 0x%08x\n",
  83                    sdhci_readw(host, SDHCI_AUTO_CMD_STATUS),
  84                    sdhci_readw(host, SDHCI_SLOT_INT_STATUS));
  85         SDHCI_DUMP("Caps:      0x%08x | Caps_1:   0x%08x\n",
  86                    sdhci_readl(host, SDHCI_CAPABILITIES),
  87                    sdhci_readl(host, SDHCI_CAPABILITIES_1));
  88         SDHCI_DUMP("Cmd:       0x%08x | Max curr: 0x%08x\n",
  89                    sdhci_readw(host, SDHCI_COMMAND),
  90                    sdhci_readl(host, SDHCI_MAX_CURRENT));
  91         SDHCI_DUMP("Resp[0]:   0x%08x | Resp[1]:  0x%08x\n",
  92                    sdhci_readl(host, SDHCI_RESPONSE),
  93                    sdhci_readl(host, SDHCI_RESPONSE + 4));
  94         SDHCI_DUMP("Resp[2]:   0x%08x | Resp[3]:  0x%08x\n",
  95                    sdhci_readl(host, SDHCI_RESPONSE + 8),
  96                    sdhci_readl(host, SDHCI_RESPONSE + 12));
  97         SDHCI_DUMP("Host ctl2: 0x%08x\n",
  98                    sdhci_readw(host, SDHCI_HOST_CONTROL2));
  99
 100         if (host->flags & SDHCI_USE_ADMA) {
 101                 if (host->flags & SDHCI_USE_64_BIT_DMA) {
 102                         SDHCI_DUMP("ADMA Err:  0x%08x | ADMA Ptr: 0x%08x%08x\n",
 103                                    sdhci_readl(host, SDHCI_ADMA_ERROR),
 104                                    sdhci_readl(host, SDHCI_ADMA_ADDRESS_HI),
 105                                    sdhci_readl(host, SDHCI_ADMA_ADDRESS));
 106                 } else {
 107                         SDHCI_DUMP("ADMA Err:  0x%08x | ADMA Ptr: 0x%08x\n",
 108                                    sdhci_readl(host, SDHCI_ADMA_ERROR),
 109                                    sdhci_readl(host, SDHCI_ADMA_ADDRESS));
 110                 }
 111         }
 112
 113         if (host->ops->dump_vendor_regs)
 114                 host->ops->dump_vendor_regs(host);
 115
 116         SDHCI_DUMP("============================================\n");
 117 }
 118 EXPORT_SYMBOL_GPL(sdhci_dumpregs);
 119
 120 /*****************************************************************************\
 121  *                                                                           *
 122  * Low level functions                                                       *
 123  *                                                                           *
 124 \*****************************************************************************/
 125
 126 static void sdhci_do_enable_v4_mode(struct sdhci_host *host)
 127 {
 128         u16 ctrl2;
 129
 130         ctrl2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
 131         if (ctrl2 & SDHCI_CTRL_V4_MODE)
 132                 return;
 133
 134         ctrl2 |= SDHCI_CTRL_V4_MODE;
 135         sdhci_writew(host, ctrl2, SDHCI_HOST_CONTROL2);
 136 }
 137
 138 /*
 139  * This can be called before sdhci_add_host() by Vendor's host controller
 140  * driver to enable v4 mode if supported.
 141  */
 142 void sdhci_enable_v4_mode(struct sdhci_host *host)
 143 {
 144         host->v4_mode = true;
 145         sdhci_do_enable_v4_mode(host);
 146 }
 147 EXPORT_SYMBOL_GPL(sdhci_enable_v4_mode);
 148
 149 static inline bool sdhci_data_line_cmd(struct mmc_command *cmd)
 150 {
 151         return cmd->data || cmd->flags & MMC_RSP_BUSY;
 152 }
 153
 154 static void sdhci_set_card_detection(struct sdhci_host *host, bool enable)
 155 {
 156         u32 present;
 157
 158         if ((host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION) ||
 159             !mmc_card_is_removable(host->mmc) || mmc_can_gpio_cd(host->mmc))
 160                 return;
 161
 162         if (enable) {
 163                 present = sdhci_readl(host, SDHCI_PRESENT_STATE) &
 164                                       SDHCI_CARD_PRESENT;
 165
 166                 host->ier |= present ? SDHCI_INT_CARD_REMOVE :
 167                                        SDHCI_INT_CARD_INSERT;
 168         } else {
 169                 host->ier &= ~(SDHCI_INT_CARD_REMOVE | SDHCI_INT_CARD_INSERT);
 170         }
 171
 172         sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
 173         sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
 174 }
 175
 176 static void sdhci_enable_card_detection(struct sdhci_host *host)
 177 {
 178         sdhci_set_card_detection(host, true);
 179 }
 180
 181 static void sdhci_disable_card_detection(struct sdhci_host *host)
 182 {
 183         sdhci_set_card_detection(host, false);
 184 }
 185
 186 static void sdhci_runtime_pm_bus_on(struct sdhci_host *host)
 187 {
 188         if (host->bus_on)
 189                 return;
 190         host->bus_on = true;
 191         pm_runtime_get_noresume(mmc_dev(host->mmc));
 192 }
 193
 194 static void sdhci_runtime_pm_bus_off(struct sdhci_host *host)
 195 {
 196         if (!host->bus_on)
 197                 return;
 198         host->bus_on = false;
 199         pm_runtime_put_noidle(mmc_dev(host->mmc));
 200 }
 201
 202 void sdhci_reset(struct sdhci_host *host, u8 mask)
 203 {
 204         ktime_t timeout;
 205
 206         sdhci_writeb(host, mask, SDHCI_SOFTWARE_RESET);
 207
 208         if (mask & SDHCI_RESET_ALL) {
 209                 host->clock = 0;
 210                 /* Reset-all turns off SD Bus Power */
 211                 if (host->quirks2 & SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON)
 212                         sdhci_runtime_pm_bus_off(host);
 213         }
 214
 215         /* Wait max 100 ms */
 216         timeout = ktime_add_ms(ktime_get(), 100);
 217
 218         /* hw clears the bit when it's done */
 219         while (1) {
 220                 bool timedout = ktime_after(ktime_get(), timeout);
 221
 222                 if (!(sdhci_readb(host, SDHCI_SOFTWARE_RESET) & mask))
 223                         break;
 224                 if (timedout) {
 225                         pr_err("%s: Reset 0x%x never completed.\n",
 226                                 mmc_hostname(host->mmc), (int)mask);
 227                         sdhci_err_stats_inc(host, CTRL_TIMEOUT);
 228                         sdhci_dumpregs(host);
 229                         return;
 230                 }
 231                 udelay(10);
 232         }
 233 }
 234 EXPORT_SYMBOL_GPL(sdhci_reset);
 235
 236 static bool sdhci_do_reset(struct sdhci_host *host, u8 mask)
 237 {
 238         if (host->quirks & SDHCI_QUIRK_NO_CARD_NO_RESET) {
 239                 struct mmc_host *mmc = host->mmc;
 240
 241                 if (!mmc->ops->get_cd(mmc))
 242                         return false;
 243         }
 244
 245         host->ops->reset(host, mask);
 246
 247         return true;
 248 }
 249
 250 static void sdhci_reset_for_all(struct sdhci_host *host)
 251 {
 252         if (sdhci_do_reset(host, SDHCI_RESET_ALL)) {
 253                 if (host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA)) {
 254                         if (host->ops->enable_dma)
 255                                 host->ops->enable_dma(host);
 256                 }
 257                 /* Resetting the controller clears many */
 258                 host->preset_enabled = false;
 259         }
 260 }
 261
 262 enum sdhci_reset_reason {
 263         SDHCI_RESET_FOR_INIT,
 264         SDHCI_RESET_FOR_REQUEST_ERROR,
 265         SDHCI_RESET_FOR_REQUEST_ERROR_DATA_ONLY,
 266         SDHCI_RESET_FOR_TUNING_ABORT,
 267         SDHCI_RESET_FOR_CARD_REMOVED,
 268         SDHCI_RESET_FOR_CQE_RECOVERY,
 269 };
 270
 271 static void sdhci_reset_for_reason(struct sdhci_host *host, enum sdhci_reset_reason reason)
 272 {
 273         if (host->quirks2 & SDHCI_QUIRK2_ISSUE_CMD_DAT_RESET_TOGETHER) {
 274                 sdhci_do_reset(host, SDHCI_RESET_CMD | SDHCI_RESET_DATA);
 275                 return;
 276         }
 277
 278         switch (reason) {
 279         case SDHCI_RESET_FOR_INIT:
 280                 sdhci_do_reset(host, SDHCI_RESET_CMD | SDHCI_RESET_DATA);
 281                 break;
 282         case SDHCI_RESET_FOR_REQUEST_ERROR:
 283         case SDHCI_RESET_FOR_TUNING_ABORT:
 284         case SDHCI_RESET_FOR_CARD_REMOVED:
 285         case SDHCI_RESET_FOR_CQE_RECOVERY:
 286                 sdhci_do_reset(host, SDHCI_RESET_CMD);
 287                 sdhci_do_reset(host, SDHCI_RESET_DATA);
 288                 break;
 289         case SDHCI_RESET_FOR_REQUEST_ERROR_DATA_ONLY:
 290                 sdhci_do_reset(host, SDHCI_RESET_DATA);
 291                 break;
 292         }
 293 }
 294
 295 #define sdhci_reset_for(h, r) sdhci_reset_for_reason((h), SDHCI_RESET_FOR_##r)
 296
 297 static void sdhci_set_default_irqs(struct sdhci_host *host)
 298 {
 299         host->ier = SDHCI_INT_BUS_POWER | SDHCI_INT_DATA_END_BIT |
 300                     SDHCI_INT_DATA_CRC | SDHCI_INT_DATA_TIMEOUT |
 301                     SDHCI_INT_INDEX | SDHCI_INT_END_BIT | SDHCI_INT_CRC |
 302                     SDHCI_INT_TIMEOUT | SDHCI_INT_DATA_END |
 303                     SDHCI_INT_RESPONSE;
 304
 305         if (host->tuning_mode == SDHCI_TUNING_MODE_2 ||
 306             host->tuning_mode == SDHCI_TUNING_MODE_3)
 307                 host->ier |= SDHCI_INT_RETUNE;
 308
 309         sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
 310         sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
 311 }
 312
 313 static void sdhci_config_dma(struct sdhci_host *host)
 314 {
 315         u8 ctrl;
 316         u16 ctrl2;
 317
 318         if (host->version < SDHCI_SPEC_200)
 319                 return;
 320
 321         ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
 322
 323         /*
 324          * Always adjust the DMA selection as some controllers
 325          * (e.g. JMicron) can't do PIO properly when the selection
 326          * is ADMA.
 327          */
 328         ctrl &= ~SDHCI_CTRL_DMA_MASK;
 329         if (!(host->flags & SDHCI_REQ_USE_DMA))
 330                 goto out;
 331
 332         /* Note if DMA Select is zero then SDMA is selected */
 333         if (host->flags & SDHCI_USE_ADMA)
 334                 ctrl |= SDHCI_CTRL_ADMA32;
 335
 336         if (host->flags & SDHCI_USE_64_BIT_DMA) {
 337                 /*
 338                  * If v4 mode, all supported DMA can be 64-bit addressing if
 339                  * controller supports 64-bit system address, otherwise only
 340                  * ADMA can support 64-bit addressing.
 341                  */
 342                 if (host->v4_mode) {
 343                         ctrl2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
 344                         ctrl2 |= SDHCI_CTRL_64BIT_ADDR;
 345                         sdhci_writew(host, ctrl2, SDHCI_HOST_CONTROL2);
 346                 } else if (host->flags & SDHCI_USE_ADMA) {
 347                         /*
 348                          * Don't need to undo SDHCI_CTRL_ADMA32 in order to
 349                          * set SDHCI_CTRL_ADMA64.
 350                          */
 351                         ctrl |= SDHCI_CTRL_ADMA64;
 352                 }
 353         }
 354
 355 out:
 356         sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
 357 }
 358
 359 static void sdhci_init(struct sdhci_host *host, int soft)
 360 {
 361         struct mmc_host *mmc = host->mmc;
 362         unsigned long flags;
 363
 364         if (soft)
 365                 sdhci_reset_for(host, INIT);
 366         else
 367                 sdhci_reset_for_all(host);
 368
 369         if (host->v4_mode)
 370                 sdhci_do_enable_v4_mode(host);
 371
 372         spin_lock_irqsave(&host->lock, flags);
 373         sdhci_set_default_irqs(host);
 374         spin_unlock_irqrestore(&host->lock, flags);
 375
 376         host->cqe_on = false;
 377
 378         if (soft) {
 379                 /* force clock reconfiguration */
 380                 host->clock = 0;
 381                 host->reinit_uhs = true;
 382                 mmc->ops->set_ios(mmc, &mmc->ios);
 383         }
 384 }
 385
 386 static void sdhci_reinit(struct sdhci_host *host)
 387 {
 388         u32 cd = host->ier & (SDHCI_INT_CARD_REMOVE | SDHCI_INT_CARD_INSERT);
 389
 390         sdhci_init(host, 0);
 391         sdhci_enable_card_detection(host);
 392
 393         /*
 394          * A change to the card detect bits indicates a change in present state,
 395          * refer sdhci_set_card_detection(). A card detect interrupt might have
 396          * been missed while the host controller was being reset, so trigger a
 397          * rescan to check.
 398          */
 399         if (cd != (host->ier & (SDHCI_INT_CARD_REMOVE | SDHCI_INT_CARD_INSERT)))
 400                 mmc_detect_change(host->mmc, msecs_to_jiffies(200));
 401 }
 402
 403 static void __sdhci_led_activate(struct sdhci_host *host)
 404 {
 405         u8 ctrl;
 406
 407         if (host->quirks & SDHCI_QUIRK_NO_LED)
 408                 return;
 409
 410         ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
 411         ctrl |= SDHCI_CTRL_LED;
 412         sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
 413 }
 414
 415 static void __sdhci_led_deactivate(struct sdhci_host *host)
 416 {
 417         u8 ctrl;
 418
 419         if (host->quirks & SDHCI_QUIRK_NO_LED)
 420                 return;
 421
 422         ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
 423         ctrl &= ~SDHCI_CTRL_LED;
 424         sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
 425 }
 426
 427 #if IS_REACHABLE(CONFIG_LEDS_CLASS)
 428 static void sdhci_led_control(struct led_classdev *led,
 429                               enum led_brightness brightness)
 430 {
 431         struct sdhci_host *host = container_of(led, struct sdhci_host, led);
 432         unsigned long flags;
 433
 434         spin_lock_irqsave(&host->lock, flags);
 435
 436         if (host->runtime_suspended)
 437                 goto out;
 438
 439         if (brightness == LED_OFF)
 440                 __sdhci_led_deactivate(host);
 441         else
 442                 __sdhci_led_activate(host);
 443 out:
 444         spin_unlock_irqrestore(&host->lock, flags);
 445 }
 446
 447 static int sdhci_led_register(struct sdhci_host *host)
 448 {
 449         struct mmc_host *mmc = host->mmc;
 450
 451         if (host->quirks & SDHCI_QUIRK_NO_LED)
 452                 return 0;
 453
 454         snprintf(host->led_name, sizeof(host->led_name),
 455                  "%s::", mmc_hostname(mmc));
 456
 457         host->led.name = host->led_name;
 458         host->led.brightness = LED_OFF;
 459         host->led.default_trigger = mmc_hostname(mmc);
 460         host->led.brightness_set = sdhci_led_control;
 461
 462         return led_classdev_register(mmc_dev(mmc), &host->led);
 463 }
 464
 465 static void sdhci_led_unregister(struct sdhci_host *host)
 466 {
 467         if (host->quirks & SDHCI_QUIRK_NO_LED)
 468                 return;
 469
 470         led_classdev_unregister(&host->led);
 471 }
 472
 473 static inline void sdhci_led_activate(struct sdhci_host *host)
 474 {
 475 }
 476
 477 static inline void sdhci_led_deactivate(struct sdhci_host *host)
 478 {
 479 }
 480
 481 #else
 482
 483 static inline int sdhci_led_register(struct sdhci_host *host)
 484 {
 485         return 0;
 486 }
 487
 488 static inline void sdhci_led_unregister(struct sdhci_host *host)
 489 {
 490 }
 491
 492 static inline void sdhci_led_activate(struct sdhci_host *host)
 493 {
 494         __sdhci_led_activate(host);
 495 }
 496
 497 static inline void sdhci_led_deactivate(struct sdhci_host *host)
 498 {
 499         __sdhci_led_deactivate(host);
 500 }
 501
 502 #endif
 503
 504 static void sdhci_mod_timer(struct sdhci_host *host, struct mmc_request *mrq,
 505                             unsigned long timeout)
 506 {
 507         if (sdhci_data_line_cmd(mrq->cmd))
 508                 mod_timer(&host->data_timer, timeout);
 509         else
 510                 mod_timer(&host->timer, timeout);
 511 }
 512
 513 static void sdhci_del_timer(struct sdhci_host *host, struct mmc_request *mrq)
 514 {
 515         if (sdhci_data_line_cmd(mrq->cmd))
 516                 del_timer(&host->data_timer);
 517         else
 518                 del_timer(&host->timer);
 519 }
 520
 521 static inline bool sdhci_has_requests(struct sdhci_host *host)
 522 {
 523         return host->cmd || host->data_cmd;
 524 }
 525
 526 /*****************************************************************************\
 527  *                                                                           *
 528  * Core functions                                                            *
 529  *                                                                           *
 530 \*****************************************************************************/
 531
 532 static void sdhci_read_block_pio(struct sdhci_host *host)
 533 {
 534         size_t blksize, len, chunk;
 535         u32 scratch;
 536         u8 *buf;
 537
 538         DBG("PIO reading\n");
 539
 540         blksize = host->data->blksz;
 541         chunk = 0;
 542
 543         while (blksize) {
 544                 BUG_ON(!sg_miter_next(&host->sg_miter));
 545
 546                 len = min(host->sg_miter.length, blksize);
 547
 548                 blksize -= len;
 549                 host->sg_miter.consumed = len;
 550
 551                 buf = host->sg_miter.addr;
 552
 553                 while (len) {
 554                         if (chunk == 0) {
 555                                 scratch = sdhci_readl(host, SDHCI_BUFFER);
 556                                 chunk = 4;
 557                         }
 558
 559                         *buf = scratch & 0xFF;
 560
 561                         buf++;
 562                         scratch >>= 8;
 563                         chunk--;
 564                         len--;
 565                 }
 566         }
 567
 568         sg_miter_stop(&host->sg_miter);
 569 }
 570
 571 static void sdhci_write_block_pio(struct sdhci_host *host)
 572 {
 573         size_t blksize, len, chunk;
 574         u32 scratch;
 575         u8 *buf;
 576
 577         DBG("PIO writing\n");
 578
 579         blksize = host->data->blksz;
 580         chunk = 0;
 581         scratch = 0;
 582
 583         while (blksize) {
 584                 BUG_ON(!sg_miter_next(&host->sg_miter));
 585
 586                 len = min(host->sg_miter.length, blksize);
 587
 588                 blksize -= len;
 589                 host->sg_miter.consumed = len;
 590
 591                 buf = host->sg_miter.addr;
 592
 593                 while (len) {
 594                         scratch |= (u32)*buf << (chunk * 8);
 595
 596                         buf++;
 597                         chunk++;
 598                         len--;
 599
 600                         if ((chunk == 4) || ((len == 0) && (blksize == 0))) {
 601                                 sdhci_writel(host, scratch, SDHCI_BUFFER);
 602                                 chunk = 0;
 603                                 scratch = 0;
 604                         }
 605                 }
 606         }
 607
 608         sg_miter_stop(&host->sg_miter);
 609 }
 610
 611 static void sdhci_transfer_pio(struct sdhci_host *host)
 612 {
 613         u32 mask;
 614
 615         if (host->blocks == 0)
 616                 return;
 617
 618         if (host->data->flags & MMC_DATA_READ)
 619                 mask = SDHCI_DATA_AVAILABLE;
 620         else
 621                 mask = SDHCI_SPACE_AVAILABLE;
 622
 623         /*
 624          * Some controllers (JMicron JMB38x) mess up the buffer bits
 625          * for transfers < 4 bytes. As long as it is just one block,
 626          * we can ignore the bits.
 627          */
 628         if ((host->quirks & SDHCI_QUIRK_BROKEN_SMALL_PIO) &&
 629                 (host->data->blocks == 1))
 630                 mask = ~0;
 631
 632         while (sdhci_readl(host, SDHCI_PRESENT_STATE) & mask) {
 633                 if (host->quirks & SDHCI_QUIRK_PIO_NEEDS_DELAY)
 634                         udelay(100);
 635
 636                 if (host->data->flags & MMC_DATA_READ)
 637                         sdhci_read_block_pio(host);
 638                 else
 639                         sdhci_write_block_pio(host);
 640
 641                 host->blocks--;
 642                 if (host->blocks == 0)
 643                         break;
 644         }
 645
 646         DBG("PIO transfer complete.\n");
 647 }
 648
 649 static int sdhci_pre_dma_transfer(struct sdhci_host *host,
 650                                   struct mmc_data *data, int cookie)
 651 {
 652         int sg_count;
 653
 654         /*
 655          * If the data buffers are already mapped, return the previous
 656          * dma_map_sg() result.
 657          */
 658         if (data->host_cookie == COOKIE_PRE_MAPPED)
 659                 return data->sg_count;
 660
 661         /* Bounce write requests to the bounce buffer */
 662         if (host->bounce_buffer) {
 663                 unsigned int length = data->blksz * data->blocks;
 664
 665                 if (length > host->bounce_buffer_size) {
 666                         pr_err("%s: asked for transfer of %u bytes exceeds bounce buffer %u bytes\n",
 667                                mmc_hostname(host->mmc), length,
 668                                host->bounce_buffer_size);
 669                         return -EIO;
 670                 }
 671                 if (mmc_get_dma_dir(data) == DMA_TO_DEVICE) {
 672                         /* Copy the data to the bounce buffer */
 673                         if (host->ops->copy_to_bounce_buffer) {
 674                                 host->ops->copy_to_bounce_buffer(host,
 675                                                                  data, length);
 676                         } else {
 677                                 sg_copy_to_buffer(data->sg, data->sg_len,
 678                                                   host->bounce_buffer, length);
 679                         }
 680                 }
 681                 /* Switch ownership to the DMA */
 682                 dma_sync_single_for_device(mmc_dev(host->mmc),
 683                                            host->bounce_addr,
 684                                            host->bounce_buffer_size,
 685                                            mmc_get_dma_dir(data));
 686                 /* Just a dummy value */
 687                 sg_count = 1;
 688         } else {
 689                 /* Just access the data directly from memory */
 690                 sg_count = dma_map_sg(mmc_dev(host->mmc),
 691                                       data->sg, data->sg_len,
 692                                       mmc_get_dma_dir(data));
 693         }
 694
 695         if (sg_count == 0)
 696                 return -ENOSPC;
 697
 698         data->sg_count = sg_count;
 699         data->host_cookie = cookie;
 700
 701         return sg_count;
 702 }
 703
 704 static char *sdhci_kmap_atomic(struct scatterlist *sg)
 705 {
 706         return kmap_local_page(sg_page(sg)) + sg->offset;
 707 }
 708
 709 static void sdhci_kunmap_atomic(void *buffer)
 710 {
 711         kunmap_local(buffer);
 712 }
 713
 714 void sdhci_adma_write_desc(struct sdhci_host *host, void **desc,
 715                            dma_addr_t addr, int len, unsigned int cmd)
 716 {
 717         struct sdhci_adma2_64_desc *dma_desc = *desc;
 718
 719         /* 32-bit and 64-bit descriptors have these members in same position */
 720         dma_desc->cmd = cpu_to_le16(cmd);
 721         dma_desc->len = cpu_to_le16(len);
 722         dma_desc->addr_lo = cpu_to_le32(lower_32_bits(addr));
 723
 724         if (host->flags & SDHCI_USE_64_BIT_DMA)
 725                 dma_desc->addr_hi = cpu_to_le32(upper_32_bits(addr));
 726
 727         *desc += host->desc_sz;
 728 }
 729 EXPORT_SYMBOL_GPL(sdhci_adma_write_desc);
 730
 731 static inline void __sdhci_adma_write_desc(struct sdhci_host *host,
 732                                            void **desc, dma_addr_t addr,
 733                                            int len, unsigned int cmd)
 734 {
 735         if (host->ops->adma_write_desc)
 736                 host->ops->adma_write_desc(host, desc, addr, len, cmd);
 737         else
 738                 sdhci_adma_write_desc(host, desc, addr, len, cmd);
 739 }
 740
 741 static void sdhci_adma_mark_end(void *desc)
 742 {
 743         struct sdhci_adma2_64_desc *dma_desc = desc;
 744
 745         /* 32-bit and 64-bit descriptors have 'cmd' in same position */
 746         dma_desc->cmd |= cpu_to_le16(ADMA2_END);
 747 }
 748
 749 static void sdhci_adma_table_pre(struct sdhci_host *host,
 750         struct mmc_data *data, int sg_count)
 751 {
 752         struct scatterlist *sg;
 753         dma_addr_t addr, align_addr;
 754         void *desc, *align;
 755         char *buffer;
 756         int len, offset, i;
 757
 758         /*
 759          * The spec does not specify endianness of descriptor table.
 760          * We currently guess that it is LE.
 761          */
 762
 763         host->sg_count = sg_count;
 764
 765         desc = host->adma_table;
 766         align = host->align_buffer;
 767
 768         align_addr = host->align_addr;
 769
 770         for_each_sg(data->sg, sg, host->sg_count, i) {
 771                 addr = sg_dma_address(sg);
 772                 len = sg_dma_len(sg);
 773
 774                 /*
 775                  * The SDHCI specification states that ADMA addresses must
 776                  * be 32-bit aligned. If they aren't, then we use a bounce
 777                  * buffer for the (up to three) bytes that screw up the
 778                  * alignment.
 779                  */
 780                 offset = (SDHCI_ADMA2_ALIGN - (addr & SDHCI_ADMA2_MASK)) &
 781                          SDHCI_ADMA2_MASK;
 782                 if (offset) {
 783                         if (data->flags & MMC_DATA_WRITE) {
 784                                 buffer = sdhci_kmap_atomic(sg);
 785                                 memcpy(align, buffer, offset);
 786                                 sdhci_kunmap_atomic(buffer);
 787                         }
 788
 789                         /* tran, valid */
 790                         __sdhci_adma_write_desc(host, &desc, align_addr,
 791                                                 offset, ADMA2_TRAN_VALID);
 792
 793                         BUG_ON(offset > 65536);
 794
 795                         align += SDHCI_ADMA2_ALIGN;
 796                         align_addr += SDHCI_ADMA2_ALIGN;
 797
 798                         addr += offset;
 799                         len -= offset;
 800                 }
 801
 802                 /*
 803                  * The block layer forces a minimum segment size of PAGE_SIZE,
 804                  * so 'len' can be too big here if PAGE_SIZE >= 64KiB. Write
 805                  * multiple descriptors, noting that the ADMA table is sized
 806                  * for 4KiB chunks anyway, so it will be big enough.
 807                  */
 808                 while (len > host->max_adma) {
 809                         int n = 32 * 1024; /* 32KiB*/
 810
 811                         __sdhci_adma_write_desc(host, &desc, addr, n, ADMA2_TRAN_VALID);
 812                         addr += n;
 813                         len -= n;
 814                 }
 815
 816                 /* tran, valid */
 817                 if (len)
 818                         __sdhci_adma_write_desc(host, &desc, addr, len,
 819                                                 ADMA2_TRAN_VALID);
 820
 821                 /*
 822                  * If this triggers then we have a calculation bug
 823                  * somewhere. :/
 824                  */
 825                 WARN_ON((desc - host->adma_table) >= host->adma_table_sz);
 826         }
 827
 828         if (host->quirks & SDHCI_QUIRK_NO_ENDATTR_IN_NOPDESC) {
 829                 /* Mark the last descriptor as the terminating descriptor */
 830                 if (desc != host->adma_table) {
 831                         desc -= host->desc_sz;
 832                         sdhci_adma_mark_end(desc);
 833                 }
 834         } else {
 835                 /* Add a terminating entry - nop, end, valid */
 836                 __sdhci_adma_write_desc(host, &desc, 0, 0, ADMA2_NOP_END_VALID);
 837         }
 838 }
 839
 840 static void sdhci_adma_table_post(struct sdhci_host *host,
 841         struct mmc_data *data)
 842 {
 843         struct scatterlist *sg;
 844         int i, size;
 845         void *align;
 846         char *buffer;
 847
 848         if (data->flags & MMC_DATA_READ) {
 849                 bool has_unaligned = false;
 850
 851                 /* Do a quick scan of the SG list for any unaligned mappings */
 852                 for_each_sg(data->sg, sg, host->sg_count, i)
 853                         if (sg_dma_address(sg) & SDHCI_ADMA2_MASK) {
 854                                 has_unaligned = true;
 855                                 break;
 856                         }
 857
 858                 if (has_unaligned) {
 859                         dma_sync_sg_for_cpu(mmc_dev(host->mmc), data->sg,
 860                                             data->sg_len, DMA_FROM_DEVICE);
 861
 862                         align = host->align_buffer;
 863
 864                         for_each_sg(data->sg, sg, host->sg_count, i) {
 865                                 if (sg_dma_address(sg) & SDHCI_ADMA2_MASK) {
 866                                         size = SDHCI_ADMA2_ALIGN -
 867                                                (sg_dma_address(sg) & SDHCI_ADMA2_MASK);
 868
 869                                         buffer = sdhci_kmap_atomic(sg);
 870                                         memcpy(buffer, align, size);
 871                                         sdhci_kunmap_atomic(buffer);
 872
 873                                         align += SDHCI_ADMA2_ALIGN;
 874                                 }
 875                         }
 876                 }
 877         }
 878 }
 879
 880 static void sdhci_set_adma_addr(struct sdhci_host *host, dma_addr_t addr)
 881 {
 882         sdhci_writel(host, lower_32_bits(addr), SDHCI_ADMA_ADDRESS);
 883         if (host->flags & SDHCI_USE_64_BIT_DMA)
 884                 sdhci_writel(host, upper_32_bits(addr), SDHCI_ADMA_ADDRESS_HI);
 885 }
 886
 887 static dma_addr_t sdhci_sdma_address(struct sdhci_host *host)
 888 {
 889         if (host->bounce_buffer)
 890                 return host->bounce_addr;
 891         else
 892                 return sg_dma_address(host->data->sg);
 893 }
 894
 895 static void sdhci_set_sdma_addr(struct sdhci_host *host, dma_addr_t addr)
 896 {
 897         if (host->v4_mode)
 898                 sdhci_set_adma_addr(host, addr);
 899         else
 900                 sdhci_writel(host, addr, SDHCI_DMA_ADDRESS);
 901 }
 902
 903 static unsigned int sdhci_target_timeout(struct sdhci_host *host,
 904                                          struct mmc_command *cmd,
 905                                          struct mmc_data *data)
 906 {
 907         unsigned int target_timeout;
 908
 909         /* timeout in us */
 910         if (!data) {
 911                 target_timeout = cmd->busy_timeout * 1000;
 912         } else {
 913                 target_timeout = DIV_ROUND_UP(data->timeout_ns, 1000);
 914                 if (host->clock && data->timeout_clks) {
 915                         unsigned long long val;
 916
 917                         /*
 918                          * data->timeout_clks is in units of clock cycles.
 919                          * host->clock is in Hz.  target_timeout is in us.
 920                          * Hence, us = 1000000 * cycles / Hz.  Round up.
 921                          */
 922                         val = 1000000ULL * data->timeout_clks;
 923                         if (do_div(val, host->clock))
 924                                 target_timeout++;
 925                         target_timeout += val;
 926                 }
 927         }
 928
 929         return target_timeout;
 930 }
 931
 932 static void sdhci_calc_sw_timeout(struct sdhci_host *host,
 933                                   struct mmc_command *cmd)
 934 {
 935         struct mmc_data *data = cmd->data;
 936         struct mmc_host *mmc = host->mmc;
 937         struct mmc_ios *ios = &mmc->ios;
 938         unsigned char bus_width = 1 << ios->bus_width;
 939         unsigned int blksz;
 940         unsigned int freq;
 941         u64 target_timeout;
 942         u64 transfer_time;
 943
 944         target_timeout = sdhci_target_timeout(host, cmd, data);
 945         target_timeout *= NSEC_PER_USEC;
 946
 947         if (data) {
 948                 blksz = data->blksz;
 949                 freq = mmc->actual_clock ? : host->clock;
 950                 transfer_time = (u64)blksz * NSEC_PER_SEC * (8 / bus_width);
 951                 do_div(transfer_time, freq);
 952                 /* multiply by '2' to account for any unknowns */
 953                 transfer_time = transfer_time * 2;
 954                 /* calculate timeout for the entire data */
 955                 host->data_timeout = data->blocks * target_timeout +
 956                                      transfer_time;
 957         } else {
 958                 host->data_timeout = target_timeout;
 959         }
 960
 961         if (host->data_timeout)
 962                 host->data_timeout += MMC_CMD_TRANSFER_TIME;
 963 }
 964
 965 static u8 sdhci_calc_timeout(struct sdhci_host *host, struct mmc_command *cmd,
 966                              bool *too_big)
 967 {
 968         u8 count;
 969         struct mmc_data *data;
 970         unsigned target_timeout, current_timeout;
 971
 972         *too_big = false;
 973
 974         /*
 975          * If the host controller provides us with an incorrect timeout
 976          * value, just skip the check and use the maximum. The hardware may take
 977          * longer to time out, but that's much better than having a too-short
 978          * timeout value.
 979          */
 980         if (host->quirks & SDHCI_QUIRK_BROKEN_TIMEOUT_VAL)
 981                 return host->max_timeout_count;
 982
 983         /* Unspecified command, assume max */
 984         if (cmd == NULL)
 985                 return host->max_timeout_count;
 986
 987         data = cmd->data;
 988         /* Unspecified timeout, assume max */
 989         if (!data && !cmd->busy_timeout)
 990                 return host->max_timeout_count;
 991
 992         /* timeout in us */
 993         target_timeout = sdhci_target_timeout(host, cmd, data);
 994
 995         /*
 996          * Figure out needed cycles.
 997          * We do this in steps in order to fit inside a 32 bit int.
 998          * The first step is the minimum timeout, which will have a
 999          * minimum resolution of 6 bits:
1000          * (1) 2^13*1000 > 2^22,
1001          * (2) host->timeout_clk < 2^16
1002          *     =>
1003          *     (1) / (2) > 2^6
1004          */
1005         count = 0;
1006         current_timeout = (1 << 13) * 1000 / host->timeout_clk;
1007         while (current_timeout < target_timeout) {
1008                 count++;
1009                 current_timeout <<= 1;
1010                 if (count > host->max_timeout_count) {
1011                         if (!(host->quirks2 & SDHCI_QUIRK2_DISABLE_HW_TIMEOUT))
1012                                 DBG("Too large timeout 0x%x requested for CMD%d!\n",
1013                                     count, cmd->opcode);
1014                         count = host->max_timeout_count;
1015                         *too_big = true;
1016                         break;
1017                 }
1018         }
1019
1020         return count;
1021 }
1022
1023 static void sdhci_set_transfer_irqs(struct sdhci_host *host)
1024 {
1025         u32 pio_irqs = SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL;
1026         u32 dma_irqs = SDHCI_INT_DMA_END | SDHCI_INT_ADMA_ERROR;
1027
1028         if (host->flags & SDHCI_REQ_USE_DMA)
1029                 host->ier = (host->ier & ~pio_irqs) | dma_irqs;
1030         else
1031                 host->ier = (host->ier & ~dma_irqs) | pio_irqs;
1032
1033         if (host->flags & (SDHCI_AUTO_CMD23 | SDHCI_AUTO_CMD12))
1034                 host->ier |= SDHCI_INT_AUTO_CMD_ERR;
1035         else
1036                 host->ier &= ~SDHCI_INT_AUTO_CMD_ERR;
1037
1038         sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
1039         sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
1040 }
1041
1042 void sdhci_set_data_timeout_irq(struct sdhci_host *host, bool enable)
1043 {
1044         if (enable)
1045                 host->ier |= SDHCI_INT_DATA_TIMEOUT;
1046         else
1047                 host->ier &= ~SDHCI_INT_DATA_TIMEOUT;
1048         sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
1049         sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
1050 }
1051 EXPORT_SYMBOL_GPL(sdhci_set_data_timeout_irq);
1052
1053 void __sdhci_set_timeout(struct sdhci_host *host, struct mmc_command *cmd)
1054 {
1055         bool too_big = false;
1056         u8 count = sdhci_calc_timeout(host, cmd, &too_big);
1057
1058         if (too_big &&
1059             host->quirks2 & SDHCI_QUIRK2_DISABLE_HW_TIMEOUT) {
1060                 sdhci_calc_sw_timeout(host, cmd);
1061                 sdhci_set_data_timeout_irq(host, false);
1062         } else if (!(host->ier & SDHCI_INT_DATA_TIMEOUT)) {
1063                 sdhci_set_data_timeout_irq(host, true);
1064         }
1065
1066         sdhci_writeb(host, count, SDHCI_TIMEOUT_CONTROL);
1067 }
1068 EXPORT_SYMBOL_GPL(__sdhci_set_timeout);
1069
1070 static void sdhci_set_timeout(struct sdhci_host *host, struct mmc_command *cmd)
1071 {
1072         if (host->ops->set_timeout)
1073                 host->ops->set_timeout(host, cmd);
1074         else
1075                 __sdhci_set_timeout(host, cmd);
1076 }
1077
1078 static void sdhci_initialize_data(struct sdhci_host *host,
1079                                   struct mmc_data *data)
1080 {
1081         WARN_ON(host->data);
1082
1083         /* Sanity checks */
1084         BUG_ON(data->blksz * data->blocks > 524288);
1085         BUG_ON(data->blksz > host->mmc->max_blk_size);
1086         BUG_ON(data->blocks > 65535);
1087
1088         host->data = data;
1089         host->data_early = 0;
1090         host->data->bytes_xfered = 0;
1091 }
1092
1093 static inline void sdhci_set_block_info(struct sdhci_host *host,
1094                                         struct mmc_data *data)
1095 {
1096         /* Set the DMA boundary value and block size */
1097         sdhci_writew(host,
1098                      SDHCI_MAKE_BLKSZ(host->sdma_boundary, data->blksz),
1099                      SDHCI_BLOCK_SIZE);
1100         /*
1101          * For Version 4.10 onwards, if v4 mode is enabled, 32-bit Block Count
1102          * can be supported, in that case 16-bit block count register must be 0.
1103          */
1104         if (host->version >= SDHCI_SPEC_410 && host->v4_mode &&
1105             (host->quirks2 & SDHCI_QUIRK2_USE_32BIT_BLK_CNT)) {
1106                 if (sdhci_readw(host, SDHCI_BLOCK_COUNT))
1107                         sdhci_writew(host, 0, SDHCI_BLOCK_COUNT);
1108                 sdhci_writew(host, data->blocks, SDHCI_32BIT_BLK_CNT);
1109         } else {
1110                 sdhci_writew(host, data->blocks, SDHCI_BLOCK_COUNT);
1111         }
1112 }
1113
1114 static void sdhci_prepare_data(struct sdhci_host *host, struct mmc_command *cmd)
1115 {
1116         struct mmc_data *data = cmd->data;
1117
1118         sdhci_initialize_data(host, data);
1119
1120         if (host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA)) {
1121                 struct scatterlist *sg;
1122                 unsigned int length_mask, offset_mask;
1123                 int i;
1124
1125                 host->flags |= SDHCI_REQ_USE_DMA;
1126
1127                 /*
1128                  * FIXME: This doesn't account for merging when mapping the
1129                  * scatterlist.
1130                  *
1131                  * The assumption here being that alignment and lengths are
1132                  * the same after DMA mapping to device address space.
1133                  */
1134                 length_mask = 0;
1135                 offset_mask = 0;
1136                 if (host->flags & SDHCI_USE_ADMA) {
1137                         if (host->quirks & SDHCI_QUIRK_32BIT_ADMA_SIZE) {
1138                                 length_mask = 3;
1139                                 /*
1140                                  * As we use up to 3 byte chunks to work
1141                                  * around alignment problems, we need to
1142                                  * check the offset as well.
1143                                  */
1144                                 offset_mask = 3;
1145                         }
1146                 } else {
1147                         if (host->quirks & SDHCI_QUIRK_32BIT_DMA_SIZE)
1148                                 length_mask = 3;
1149                         if (host->quirks & SDHCI_QUIRK_32BIT_DMA_ADDR)
1150                                 offset_mask = 3;
1151                 }
1152
1153                 if (unlikely(length_mask | offset_mask)) {
1154                         for_each_sg(data->sg, sg, data->sg_len, i) {
1155                                 if (sg->length & length_mask) {
1156                                         DBG("Reverting to PIO because of transfer size (%d)\n",
1157                                             sg->length);
1158                                         host->flags &= ~SDHCI_REQ_USE_DMA;
1159                                         break;
1160                                 }
1161                                 if (sg->offset & offset_mask) {
1162                                         DBG("Reverting to PIO because of bad alignment\n");
1163                                         host->flags &= ~SDHCI_REQ_USE_DMA;
1164                                         break;
1165                                 }
1166                         }
1167                 }
1168         }
1169
1170         sdhci_config_dma(host);
1171
1172         if (host->flags & SDHCI_REQ_USE_DMA) {
1173                 int sg_cnt = sdhci_pre_dma_transfer(host, data, COOKIE_MAPPED);
1174
1175                 if (sg_cnt <= 0) {
1176                         /*
1177                          * This only happens when someone fed
1178                          * us an invalid request.
1179                          */
1180                         WARN_ON(1);
1181                         host->flags &= ~SDHCI_REQ_USE_DMA;
1182                 } else if (host->flags & SDHCI_USE_ADMA) {
1183                         sdhci_adma_table_pre(host, data, sg_cnt);
1184                         sdhci_set_adma_addr(host, host->adma_addr);
1185                 } else {
1186                         WARN_ON(sg_cnt != 1);
1187                         sdhci_set_sdma_addr(host, sdhci_sdma_address(host));
1188                 }
1189         }
1190
1191         if (!(host->flags & SDHCI_REQ_USE_DMA)) {
1192                 int flags;
1193
1194                 flags = SG_MITER_ATOMIC;
1195                 if (host->data->flags & MMC_DATA_READ)
1196                         flags |= SG_MITER_TO_SG;
1197                 else
1198                         flags |= SG_MITER_FROM_SG;
1199                 sg_miter_start(&host->sg_miter, data->sg, data->sg_len, flags);
1200                 host->blocks = data->blocks;
1201         }
1202
1203         sdhci_set_transfer_irqs(host);
1204
1205         sdhci_set_block_info(host, data);
1206 }
1207
1208 #if IS_ENABLED(CONFIG_MMC_SDHCI_EXTERNAL_DMA)
1209
1210 static int sdhci_external_dma_init(struct sdhci_host *host)
1211 {
1212         int ret = 0;
1213         struct mmc_host *mmc = host->mmc;
1214
1215         host->tx_chan = dma_request_chan(mmc_dev(mmc), "tx");
1216         if (IS_ERR(host->tx_chan)) {
1217                 ret = PTR_ERR(host->tx_chan);
1218                 if (ret != -EPROBE_DEFER)
1219                         pr_warn("Failed to request TX DMA channel.\n");
1220                 host->tx_chan = NULL;
1221                 return ret;
1222         }
1223
1224         host->rx_chan = dma_request_chan(mmc_dev(mmc), "rx");
1225         if (IS_ERR(host->rx_chan)) {
1226                 if (host->tx_chan) {
1227                         dma_release_channel(host->tx_chan);
1228                         host->tx_chan = NULL;
1229                 }
1230
1231                 ret = PTR_ERR(host->rx_chan);
1232                 if (ret != -EPROBE_DEFER)
1233                         pr_warn("Failed to request RX DMA channel.\n");
1234                 host->rx_chan = NULL;
1235         }
1236
1237         return ret;
1238 }
1239
1240 static struct dma_chan *sdhci_external_dma_channel(struct sdhci_host *host,
1241                                                    struct mmc_data *data)
1242 {
1243         return data->flags & MMC_DATA_WRITE ? host->tx_chan : host->rx_chan;
1244 }
1245
1246 static int sdhci_external_dma_setup(struct sdhci_host *host,
1247                                     struct mmc_command *cmd)
1248 {
1249         int ret, i;
1250         enum dma_transfer_direction dir;
1251         struct dma_async_tx_descriptor *desc;
1252         struct mmc_data *data = cmd->data;
1253         struct dma_chan *chan;
1254         struct dma_slave_config cfg;
1255         dma_cookie_t cookie;
1256         int sg_cnt;
1257
1258         if (!host->mapbase)
1259                 return -EINVAL;
1260
1261         memset(&cfg, 0, sizeof(cfg));
1262         cfg.src_addr = host->mapbase + SDHCI_BUFFER;
1263         cfg.dst_addr = host->mapbase + SDHCI_BUFFER;
1264         cfg.src_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
1265         cfg.dst_addr_width = DMA_SLAVE_BUSWIDTH_4_BYTES;
1266         cfg.src_maxburst = data->blksz / 4;
1267         cfg.dst_maxburst = data->blksz / 4;
1268
1269         /* Sanity check: all the SG entries must be aligned by block size. */
1270         for (i = 0; i < data->sg_len; i++) {
1271                 if ((data->sg + i)->length % data->blksz)
1272                         return -EINVAL;
1273         }
1274
1275         chan = sdhci_external_dma_channel(host, data);
1276
1277         ret = dmaengine_slave_config(chan, &cfg);
1278         if (ret)
1279                 return ret;
1280
1281         sg_cnt = sdhci_pre_dma_transfer(host, data, COOKIE_MAPPED);
1282         if (sg_cnt <= 0)
1283                 return -EINVAL;
1284
1285         dir = data->flags & MMC_DATA_WRITE ? DMA_MEM_TO_DEV : DMA_DEV_TO_MEM;
1286         desc = dmaengine_prep_slave_sg(chan, data->sg, data->sg_len, dir,
1287                                        DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
1288         if (!desc)
1289                 return -EINVAL;
1290
1291         desc->callback = NULL;
1292         desc->callback_param = NULL;
1293
1294         cookie = dmaengine_submit(desc);
1295         if (dma_submit_error(cookie))
1296                 ret = cookie;
1297
1298         return ret;
1299 }
1300
1301 static void sdhci_external_dma_release(struct sdhci_host *host)
1302 {
1303         if (host->tx_chan) {
1304                 dma_release_channel(host->tx_chan);
1305                 host->tx_chan = NULL;
1306         }
1307
1308         if (host->rx_chan) {
1309                 dma_release_channel(host->rx_chan);
1310                 host->rx_chan = NULL;
1311         }
1312
1313         sdhci_switch_external_dma(host, false);
1314 }
1315
1316 static void __sdhci_external_dma_prepare_data(struct sdhci_host *host,
1317                                               struct mmc_command *cmd)
1318 {
1319         struct mmc_data *data = cmd->data;
1320
1321         sdhci_initialize_data(host, data);
1322
1323         host->flags |= SDHCI_REQ_USE_DMA;
1324         sdhci_set_transfer_irqs(host);
1325
1326         sdhci_set_block_info(host, data);
1327 }
1328
1329 static void sdhci_external_dma_prepare_data(struct sdhci_host *host,
1330                                             struct mmc_command *cmd)
1331 {
1332         if (!sdhci_external_dma_setup(host, cmd)) {
1333                 __sdhci_external_dma_prepare_data(host, cmd);
1334         } else {
1335                 sdhci_external_dma_release(host);
1336                 pr_err("%s: Cannot use external DMA, switch to the DMA/PIO which standard SDHCI provides.\n",
1337                        mmc_hostname(host->mmc));
1338                 sdhci_prepare_data(host, cmd);
1339         }
1340 }
1341
1342 static void sdhci_external_dma_pre_transfer(struct sdhci_host *host,
1343                                             struct mmc_command *cmd)
1344 {
1345         struct dma_chan *chan;
1346
1347         if (!cmd->data)
1348                 return;
1349
1350         chan = sdhci_external_dma_channel(host, cmd->data);
1351         if (chan)
1352                 dma_async_issue_pending(chan);
1353 }
1354
1355 #else
1356
1357 static inline int sdhci_external_dma_init(struct sdhci_host *host)
1358 {
1359         return -EOPNOTSUPP;
1360 }
1361
1362 static inline void sdhci_external_dma_release(struct sdhci_host *host)
1363 {
1364 }
1365
1366 static inline void sdhci_external_dma_prepare_data(struct sdhci_host *host,
1367                                                    struct mmc_command *cmd)
1368 {
1369         /* This should never happen */
1370         WARN_ON_ONCE(1);
1371 }
1372
1373 static inline void sdhci_external_dma_pre_transfer(struct sdhci_host *host,
1374                                                    struct mmc_command *cmd)
1375 {
1376 }
1377
1378 static inline struct dma_chan *sdhci_external_dma_channel(struct sdhci_host *host,
1379                                                           struct mmc_data *data)
1380 {
1381         return NULL;
1382 }
1383
1384 #endif
1385
1386 void sdhci_switch_external_dma(struct sdhci_host *host, bool en)
1387 {
1388         host->use_external_dma = en;
1389 }
1390 EXPORT_SYMBOL_GPL(sdhci_switch_external_dma);
1391
1392 static inline bool sdhci_auto_cmd12(struct sdhci_host *host,
1393                                     struct mmc_request *mrq)
1394 {
1395         return !mrq->sbc && (host->flags & SDHCI_AUTO_CMD12) &&
1396                !mrq->cap_cmd_during_tfr;
1397 }
1398
1399 static inline bool sdhci_auto_cmd23(struct sdhci_host *host,
1400                                     struct mmc_request *mrq)
1401 {
1402         return mrq->sbc && (host->flags & SDHCI_AUTO_CMD23);
1403 }
1404
1405 static inline bool sdhci_manual_cmd23(struct sdhci_host *host,
1406                                       struct mmc_request *mrq)
1407 {
1408         return mrq->sbc && !(host->flags & SDHCI_AUTO_CMD23);
1409 }
1410
1411 static inline void sdhci_auto_cmd_select(struct sdhci_host *host,
1412                                          struct mmc_command *cmd,
1413                                          u16 *mode)
1414 {
1415         bool use_cmd12 = sdhci_auto_cmd12(host, cmd->mrq) &&
1416                          (cmd->opcode != SD_IO_RW_EXTENDED);
1417         bool use_cmd23 = sdhci_auto_cmd23(host, cmd->mrq);
1418         u16 ctrl2;
1419
1420         /*
1421          * In case of Version 4.10 or later, use of 'Auto CMD Auto
1422          * Select' is recommended rather than use of 'Auto CMD12
1423          * Enable' or 'Auto CMD23 Enable'. We require Version 4 Mode
1424          * here because some controllers (e.g sdhci-of-dwmshc) expect it.
1425          */
1426         if (host->version >= SDHCI_SPEC_410 && host->v4_mode &&
1427             (use_cmd12 || use_cmd23)) {
1428                 *mode |= SDHCI_TRNS_AUTO_SEL;
1429
1430                 ctrl2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
1431                 if (use_cmd23)
1432                         ctrl2 |= SDHCI_CMD23_ENABLE;
1433                 else
1434                         ctrl2 &= ~SDHCI_CMD23_ENABLE;
1435                 sdhci_writew(host, ctrl2, SDHCI_HOST_CONTROL2);
1436
1437                 return;
1438         }
1439
1440         /*
1441          * If we are sending CMD23, CMD12 never gets sent
1442          * on successful completion (so no Auto-CMD12).
1443          */
1444         if (use_cmd12)
1445                 *mode |= SDHCI_TRNS_AUTO_CMD12;
1446         else if (use_cmd23)
1447                 *mode |= SDHCI_TRNS_AUTO_CMD23;
1448 }
1449
1450 static void sdhci_set_transfer_mode(struct sdhci_host *host,
1451         struct mmc_command *cmd)
1452 {
1453         u16 mode = 0;
1454         struct mmc_data *data = cmd->data;
1455
1456         if (data == NULL) {
1457                 if (host->quirks2 &
1458                         SDHCI_QUIRK2_CLEAR_TRANSFERMODE_REG_BEFORE_CMD) {
1459                         /* must not clear SDHCI_TRANSFER_MODE when tuning */
1460                         if (!mmc_op_tuning(cmd->opcode))
1461                                 sdhci_writew(host, 0x0, SDHCI_TRANSFER_MODE);
1462                 } else {
1463                 /* clear Auto CMD settings for no data CMDs */
1464                         mode = sdhci_readw(host, SDHCI_TRANSFER_MODE);
1465                         sdhci_writew(host, mode & ~(SDHCI_TRNS_AUTO_CMD12 |
1466                                 SDHCI_TRNS_AUTO_CMD23), SDHCI_TRANSFER_MODE);
1467                 }
1468                 return;
1469         }
1470
1471         WARN_ON(!host->data);
1472
1473         if (!(host->quirks2 & SDHCI_QUIRK2_SUPPORT_SINGLE))
1474                 mode = SDHCI_TRNS_BLK_CNT_EN;
1475
1476         if (mmc_op_multi(cmd->opcode) || data->blocks > 1) {
1477                 mode = SDHCI_TRNS_BLK_CNT_EN | SDHCI_TRNS_MULTI;
1478                 sdhci_auto_cmd_select(host, cmd, &mode);
1479                 if (sdhci_auto_cmd23(host, cmd->mrq))
1480                         sdhci_writel(host, cmd->mrq->sbc->arg, SDHCI_ARGUMENT2);
1481         }
1482
1483         if (data->flags & MMC_DATA_READ)
1484                 mode |= SDHCI_TRNS_READ;
1485         if (host->flags & SDHCI_REQ_USE_DMA)
1486                 mode |= SDHCI_TRNS_DMA;
1487
1488         sdhci_writew(host, mode, SDHCI_TRANSFER_MODE);
1489 }
1490
1491 static bool sdhci_needs_reset(struct sdhci_host *host, struct mmc_request *mrq)
1492 {
1493         return (!(host->flags & SDHCI_DEVICE_DEAD) &&
1494                 ((mrq->cmd && mrq->cmd->error) ||
1495                  (mrq->sbc && mrq->sbc->error) ||
1496                  (mrq->data && mrq->data->stop && mrq->data->stop->error) ||
1497                  (host->quirks & SDHCI_QUIRK_RESET_AFTER_REQUEST)));
1498 }
1499
1500 static void sdhci_set_mrq_done(struct sdhci_host *host, struct mmc_request *mrq)
1501 {
1502         int i;
1503
1504         for (i = 0; i < SDHCI_MAX_MRQS; i++) {
1505                 if (host->mrqs_done[i] == mrq) {
1506                         WARN_ON(1);
1507                         return;
1508                 }
1509         }
1510
1511         for (i = 0; i < SDHCI_MAX_MRQS; i++) {
1512                 if (!host->mrqs_done[i]) {
1513                         host->mrqs_done[i] = mrq;
1514                         break;
1515                 }
1516         }
1517
1518         WARN_ON(i >= SDHCI_MAX_MRQS);
1519 }
1520
1521 static void __sdhci_finish_mrq(struct sdhci_host *host, struct mmc_request *mrq)
1522 {
1523         if (host->cmd && host->cmd->mrq == mrq)
1524                 host->cmd = NULL;
1525
1526         if (host->data_cmd && host->data_cmd->mrq == mrq)
1527                 host->data_cmd = NULL;
1528
1529         if (host->deferred_cmd && host->deferred_cmd->mrq == mrq)
1530                 host->deferred_cmd = NULL;
1531
1532         if (host->data && host->data->mrq == mrq)
1533                 host->data = NULL;
1534
1535         if (sdhci_needs_reset(host, mrq))
1536                 host->pending_reset = true;
1537
1538         sdhci_set_mrq_done(host, mrq);
1539
1540         sdhci_del_timer(host, mrq);
1541
1542         if (!sdhci_has_requests(host))
1543                 sdhci_led_deactivate(host);
1544 }
1545
1546 static void sdhci_finish_mrq(struct sdhci_host *host, struct mmc_request *mrq)
1547 {
1548         __sdhci_finish_mrq(host, mrq);
1549
1550         queue_work(host->complete_wq, &host->complete_work);
1551 }
1552
1553 static void __sdhci_finish_data(struct sdhci_host *host, bool sw_data_timeout)
1554 {
1555         struct mmc_command *data_cmd = host->data_cmd;
1556         struct mmc_data *data = host->data;
1557
1558         host->data = NULL;
1559         host->data_cmd = NULL;
1560
1561         /*
1562          * The controller needs a reset of internal state machines upon error
1563          * conditions.
1564          */
1565         if (data->error) {
1566                 if (!host->cmd || host->cmd == data_cmd)
1567                         sdhci_reset_for(host, REQUEST_ERROR);
1568                 else
1569                         sdhci_reset_for(host, REQUEST_ERROR_DATA_ONLY);
1570         }
1571
1572         if ((host->flags & (SDHCI_REQ_USE_DMA | SDHCI_USE_ADMA)) ==
1573             (SDHCI_REQ_USE_DMA | SDHCI_USE_ADMA))
1574                 sdhci_adma_table_post(host, data);
1575
1576         /*
1577          * The specification states that the block count register must
1578          * be updated, but it does not specify at what point in the
1579          * data flow. That makes the register entirely useless to read
1580          * back so we have to assume that nothing made it to the card
1581          * in the event of an error.
1582          */
1583         if (data->error)
1584                 data->bytes_xfered = 0;
1585         else
1586                 data->bytes_xfered = data->blksz * data->blocks;
1587
1588         /*
1589          * Need to send CMD12 if -
1590          * a) open-ended multiblock transfer not using auto CMD12 (no CMD23)
1591          * b) error in multiblock transfer
1592          */
1593         if (data->stop &&
1594             ((!data->mrq->sbc && !sdhci_auto_cmd12(host, data->mrq)) ||
1595              data->error)) {
1596                 /*
1597                  * 'cap_cmd_during_tfr' request must not use the command line
1598                  * after mmc_command_done() has been called. It is upper layer's
1599                  * responsibility to send the stop command if required.
1600                  */
1601                 if (data->mrq->cap_cmd_during_tfr) {
1602                         __sdhci_finish_mrq(host, data->mrq);
1603                 } else {
1604                         /* Avoid triggering warning in sdhci_send_command() */
1605                         host->cmd = NULL;
1606                         if (!sdhci_send_command(host, data->stop)) {
1607                                 if (sw_data_timeout) {
1608                                         /*
1609                                          * This is anyway a sw data timeout, so
1610                                          * give up now.
1611                                          */
1612                                         data->stop->error = -EIO;
1613                                         __sdhci_finish_mrq(host, data->mrq);
1614                                 } else {
1615                                         WARN_ON(host->deferred_cmd);
1616                                         host->deferred_cmd = data->stop;
1617                                 }
1618                         }
1619                 }
1620         } else {
1621                 __sdhci_finish_mrq(host, data->mrq);
1622         }
1623 }
1624
1625 static void sdhci_finish_data(struct sdhci_host *host)
1626 {
1627         __sdhci_finish_data(host, false);
1628 }
1629
1630 static bool sdhci_send_command(struct sdhci_host *host, struct mmc_command *cmd)
1631 {
1632         int flags;
1633         u32 mask;
1634         unsigned long timeout;
1635
1636         WARN_ON(host->cmd);
1637
1638         /* Initially, a command has no error */
1639         cmd->error = 0;
1640
1641         if ((host->quirks2 & SDHCI_QUIRK2_STOP_WITH_TC) &&
1642             cmd->opcode == MMC_STOP_TRANSMISSION)
1643                 cmd->flags |= MMC_RSP_BUSY;
1644
1645         mask = SDHCI_CMD_INHIBIT;
1646         if (sdhci_data_line_cmd(cmd))
1647                 mask |= SDHCI_DATA_INHIBIT;
1648
1649         /* We shouldn't wait for data inihibit for stop commands, even
1650            though they might use busy signaling */
1651         if (cmd->mrq->data && (cmd == cmd->mrq->data->stop))
1652                 mask &= ~SDHCI_DATA_INHIBIT;
1653
1654         if (sdhci_readl(host, SDHCI_PRESENT_STATE) & mask)
1655                 return false;
1656
1657         host->cmd = cmd;
1658         host->data_timeout = 0;
1659         if (sdhci_data_line_cmd(cmd)) {
1660                 WARN_ON(host->data_cmd);
1661                 host->data_cmd = cmd;
1662                 sdhci_set_timeout(host, cmd);
1663         }
1664
1665         if (cmd->data) {
1666                 if (host->use_external_dma)
1667                         sdhci_external_dma_prepare_data(host, cmd);
1668                 else
1669                         sdhci_prepare_data(host, cmd);
1670         }
1671
1672         sdhci_writel(host, cmd->arg, SDHCI_ARGUMENT);
1673
1674         sdhci_set_transfer_mode(host, cmd);
1675
1676         if ((cmd->flags & MMC_RSP_136) && (cmd->flags & MMC_RSP_BUSY)) {
1677                 WARN_ONCE(1, "Unsupported response type!\n");
1678                 /*
1679                  * This does not happen in practice because 136-bit response
1680                  * commands never have busy waiting, so rather than complicate
1681                  * the error path, just remove busy waiting and continue.
1682                  */
1683                 cmd->flags &= ~MMC_RSP_BUSY;
1684         }
1685
1686         if (!(cmd->flags & MMC_RSP_PRESENT))
1687                 flags = SDHCI_CMD_RESP_NONE;
1688         else if (cmd->flags & MMC_RSP_136)
1689                 flags = SDHCI_CMD_RESP_LONG;
1690         else if (cmd->flags & MMC_RSP_BUSY)
1691                 flags = SDHCI_CMD_RESP_SHORT_BUSY;
1692         else
1693                 flags = SDHCI_CMD_RESP_SHORT;
1694
1695         if (cmd->flags & MMC_RSP_CRC)
1696                 flags |= SDHCI_CMD_CRC;
1697         if (cmd->flags & MMC_RSP_OPCODE)
1698                 flags |= SDHCI_CMD_INDEX;
1699
1700         /* CMD19 is special in that the Data Present Select should be set */
1701         if (cmd->data || mmc_op_tuning(cmd->opcode))
1702                 flags |= SDHCI_CMD_DATA;
1703
1704         timeout = jiffies;
1705         if (host->data_timeout)
1706                 timeout += nsecs_to_jiffies(host->data_timeout);
1707         else if (!cmd->data && cmd->busy_timeout > 9000)
1708                 timeout += DIV_ROUND_UP(cmd->busy_timeout, 1000) * HZ + HZ;
1709         else
1710                 timeout += 10 * HZ;
1711         sdhci_mod_timer(host, cmd->mrq, timeout);
1712
1713         if (host->use_external_dma)
1714                 sdhci_external_dma_pre_transfer(host, cmd);
1715
1716         sdhci_writew(host, SDHCI_MAKE_CMD(cmd->opcode, flags), SDHCI_COMMAND);
1717
1718         return true;
1719 }
1720
1721 static bool sdhci_present_error(struct sdhci_host *host,
1722                                 struct mmc_command *cmd, bool present)
1723 {
1724         if (!present || host->flags & SDHCI_DEVICE_DEAD) {
1725                 cmd->error = -ENOMEDIUM;
1726                 return true;
1727         }
1728
1729         return false;
1730 }
1731
1732 static bool sdhci_send_command_retry(struct sdhci_host *host,
1733                                      struct mmc_command *cmd,
1734                                      unsigned long flags)
1735         __releases(host->lock)
1736         __acquires(host->lock)
1737 {
1738         struct mmc_command *deferred_cmd = host->deferred_cmd;
1739         int timeout = 10; /* Approx. 10 ms */
1740         bool present;
1741
1742         while (!sdhci_send_command(host, cmd)) {
1743                 if (!timeout--) {
1744                         pr_err("%s: Controller never released inhibit bit(s).\n",
1745                                mmc_hostname(host->mmc));
1746                         sdhci_err_stats_inc(host, CTRL_TIMEOUT);
1747                         sdhci_dumpregs(host);
1748                         cmd->error = -EIO;
1749                         return false;
1750                 }
1751
1752                 spin_unlock_irqrestore(&host->lock, flags);
1753
1754                 usleep_range(1000, 1250);
1755
1756                 present = host->mmc->ops->get_cd(host->mmc);
1757
1758                 spin_lock_irqsave(&host->lock, flags);
1759
1760                 /* A deferred command might disappear, handle that */
1761                 if (cmd == deferred_cmd && cmd != host->deferred_cmd)
1762                         return true;
1763
1764                 if (sdhci_present_error(host, cmd, present))
1765                         return false;
1766         }
1767
1768         if (cmd == host->deferred_cmd)
1769                 host->deferred_cmd = NULL;
1770
1771         return true;
1772 }
1773
1774 static void sdhci_read_rsp_136(struct sdhci_host *host, struct mmc_command *cmd)
1775 {
1776         int i, reg;
1777
1778         for (i = 0; i < 4; i++) {
1779                 reg = SDHCI_RESPONSE + (3 - i) * 4;
1780                 cmd->resp[i] = sdhci_readl(host, reg);
1781         }
1782
1783         if (host->quirks2 & SDHCI_QUIRK2_RSP_136_HAS_CRC)
1784                 return;
1785
1786         /* CRC is stripped so we need to do some shifting */
1787         for (i = 0; i < 4; i++) {
1788                 cmd->resp[i] <<= 8;
1789                 if (i != 3)
1790                         cmd->resp[i] |= cmd->resp[i + 1] >> 24;
1791         }
1792 }
1793
1794 static void sdhci_finish_command(struct sdhci_host *host)
1795 {
1796         struct mmc_command *cmd = host->cmd;
1797
1798         host->cmd = NULL;
1799
1800         if (cmd->flags & MMC_RSP_PRESENT) {
1801                 if (cmd->flags & MMC_RSP_136) {
1802                         sdhci_read_rsp_136(host, cmd);
1803                 } else {
1804                         cmd->resp[0] = sdhci_readl(host, SDHCI_RESPONSE);
1805                 }
1806         }
1807
1808         if (cmd->mrq->cap_cmd_during_tfr && cmd == cmd->mrq->cmd)
1809                 mmc_command_done(host->mmc, cmd->mrq);
1810
1811         /*
1812          * The host can send and interrupt when the busy state has
1813          * ended, allowing us to wait without wasting CPU cycles.
1814          * The busy signal uses DAT0 so this is similar to waiting
1815          * for data to complete.
1816          *
1817          * Note: The 1.0 specification is a bit ambiguous about this
1818          *       feature so there might be some problems with older
1819          *       controllers.
1820          */
1821         if (cmd->flags & MMC_RSP_BUSY) {
1822                 if (cmd->data) {
1823                         DBG("Cannot wait for busy signal when also doing a data transfer");
1824                 } else if (!(host->quirks & SDHCI_QUIRK_NO_BUSY_IRQ) &&
1825                            cmd == host->data_cmd) {
1826                         /* Command complete before busy is ended */
1827                         return;
1828                 }
1829         }
1830
1831         /* Finished CMD23, now send actual command. */
1832         if (cmd == cmd->mrq->sbc) {
1833                 if (!sdhci_send_command(host, cmd->mrq->cmd)) {
1834                         WARN_ON(host->deferred_cmd);
1835                         host->deferred_cmd = cmd->mrq->cmd;
1836                 }
1837         } else {
1838
1839                 /* Processed actual command. */
1840                 if (host->data && host->data_early)
1841                         sdhci_finish_data(host);
1842
1843                 if (!cmd->data)
1844                         __sdhci_finish_mrq(host, cmd->mrq);
1845         }
1846 }
1847
1848 static u16 sdhci_get_preset_value(struct sdhci_host *host)
1849 {
1850         u16 preset = 0;
1851
1852         switch (host->timing) {
1853         case MMC_TIMING_MMC_HS:
1854         case MMC_TIMING_SD_HS:
1855                 preset = sdhci_readw(host, SDHCI_PRESET_FOR_HIGH_SPEED);
1856                 break;
1857         case MMC_TIMING_UHS_SDR12:
1858                 preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR12);
1859                 break;
1860         case MMC_TIMING_UHS_SDR25:
1861                 preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR25);
1862                 break;
1863         case MMC_TIMING_UHS_SDR50:
1864                 preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR50);
1865                 break;
1866         case MMC_TIMING_UHS_SDR104:
1867         case MMC_TIMING_MMC_HS200:
1868                 preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR104);
1869                 break;
1870         case MMC_TIMING_UHS_DDR50:
1871         case MMC_TIMING_MMC_DDR52:
1872                 preset = sdhci_readw(host, SDHCI_PRESET_FOR_DDR50);
1873                 break;
1874         case MMC_TIMING_MMC_HS400:
1875                 preset = sdhci_readw(host, SDHCI_PRESET_FOR_HS400);
1876                 break;
1877         default:
1878                 pr_warn("%s: Invalid UHS-I mode selected\n",
1879                         mmc_hostname(host->mmc));
1880                 preset = sdhci_readw(host, SDHCI_PRESET_FOR_SDR12);
1881                 break;
1882         }
1883         return preset;
1884 }
1885
1886 u16 sdhci_calc_clk(struct sdhci_host *host, unsigned int clock,
1887                    unsigned int *actual_clock)
1888 {
1889         int div = 0; /* Initialized for compiler warning */
1890         int real_div = div, clk_mul = 1;
1891         u16 clk = 0;
1892         bool switch_base_clk = false;
1893
1894         if (host->version >= SDHCI_SPEC_300) {
1895                 if (host->preset_enabled) {
1896                         u16 pre_val;
1897
1898                         clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
1899                         pre_val = sdhci_get_preset_value(host);
1900                         div = FIELD_GET(SDHCI_PRESET_SDCLK_FREQ_MASK, pre_val);
1901                         if (host->clk_mul &&
1902                                 (pre_val & SDHCI_PRESET_CLKGEN_SEL)) {
1903                                 clk = SDHCI_PROG_CLOCK_MODE;
1904                                 real_div = div + 1;
1905                                 clk_mul = host->clk_mul;
1906                         } else {
1907                                 real_div = max_t(int, 1, div << 1);
1908                         }
1909                         goto clock_set;
1910                 }
1911
1912                 /*
1913                  * Check if the Host Controller supports Programmable Clock
1914                  * Mode.
1915                  */
1916                 if (host->clk_mul) {
1917                         for (div = 1; div <= 1024; div++) {
1918                                 if ((host->max_clk * host->clk_mul / div)
1919                                         <= clock)
1920                                         break;
1921                         }
1922                         if ((host->max_clk * host->clk_mul / div) <= clock) {
1923                                 /*
1924                                  * Set Programmable Clock Mode in the Clock
1925                                  * Control register.
1926                                  */
1927                                 clk = SDHCI_PROG_CLOCK_MODE;
1928                                 real_div = div;
1929                                 clk_mul = host->clk_mul;
1930                                 div--;
1931                         } else {
1932                                 /*
1933                                  * Divisor can be too small to reach clock
1934                                  * speed requirement. Then use the base clock.
1935                                  */
1936                                 switch_base_clk = true;
1937                         }
1938                 }
1939
1940                 if (!host->clk_mul || switch_base_clk) {
1941                         /* Version 3.00 divisors must be a multiple of 2. */
1942                         if (host->max_clk <= clock)
1943                                 div = 1;
1944                         else {
1945                                 for (div = 2; div < SDHCI_MAX_DIV_SPEC_300;
1946                                      div += 2) {
1947                                         if ((host->max_clk / div) <= clock)
1948                                                 break;
1949                                 }
1950                         }
1951                         real_div = div;
1952                         div >>= 1;
1953                         if ((host->quirks2 & SDHCI_QUIRK2_CLOCK_DIV_ZERO_BROKEN)
1954                                 && !div && host->max_clk <= 25000000)
1955                                 div = 1;
1956                 }
1957         } else {
1958                 /* Version 2.00 divisors must be a power of 2. */
1959                 for (div = 1; div < SDHCI_MAX_DIV_SPEC_200; div *= 2) {
1960                         if ((host->max_clk / div) <= clock)
1961                                 break;
1962                 }
1963                 real_div = div;
1964                 div >>= 1;
1965         }
1966
1967 clock_set:
1968         if (real_div)
1969                 *actual_clock = (host->max_clk * clk_mul) / real_div;
1970         clk |= (div & SDHCI_DIV_MASK) << SDHCI_DIVIDER_SHIFT;
1971         clk |= ((div & SDHCI_DIV_HI_MASK) >> SDHCI_DIV_MASK_LEN)
1972                 << SDHCI_DIVIDER_HI_SHIFT;
1973
1974         return clk;
1975 }
1976 EXPORT_SYMBOL_GPL(sdhci_calc_clk);
1977
1978 void sdhci_enable_clk(struct sdhci_host *host, u16 clk)
1979 {
1980         ktime_t timeout;
1981
1982         clk |= SDHCI_CLOCK_INT_EN;
1983         sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
1984
1985         /* Wait max 150 ms */
1986         timeout = ktime_add_ms(ktime_get(), 150);
1987         while (1) {
1988                 bool timedout = ktime_after(ktime_get(), timeout);
1989
1990                 clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
1991                 if (clk & SDHCI_CLOCK_INT_STABLE)
1992                         break;
1993                 if (timedout) {
1994                         pr_err("%s: Internal clock never stabilised.\n",
1995                                mmc_hostname(host->mmc));
1996                         sdhci_err_stats_inc(host, CTRL_TIMEOUT);
1997                         sdhci_dumpregs(host);
1998                         return;
1999                 }
2000                 udelay(10);
2001         }
2002
2003         if (host->version >= SDHCI_SPEC_410 && host->v4_mode) {
2004                 clk |= SDHCI_CLOCK_PLL_EN;
2005                 clk &= ~SDHCI_CLOCK_INT_STABLE;
2006                 sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
2007
2008                 /* Wait max 150 ms */
2009                 timeout = ktime_add_ms(ktime_get(), 150);
2010                 while (1) {
2011                         bool timedout = ktime_after(ktime_get(), timeout);
2012
2013                         clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
2014                         if (clk & SDHCI_CLOCK_INT_STABLE)
2015                                 break;
2016                         if (timedout) {
2017                                 pr_err("%s: PLL clock never stabilised.\n",
2018                                        mmc_hostname(host->mmc));
2019                                 sdhci_err_stats_inc(host, CTRL_TIMEOUT);
2020                                 sdhci_dumpregs(host);
2021                                 return;
2022                         }
2023                         udelay(10);
2024                 }
2025         }
2026
2027         clk |= SDHCI_CLOCK_CARD_EN;
2028         sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
2029 }
2030 EXPORT_SYMBOL_GPL(sdhci_enable_clk);
2031
2032 void sdhci_set_clock(struct sdhci_host *host, unsigned int clock)
2033 {
2034         u16 clk;
2035
2036         host->mmc->actual_clock = 0;
2037
2038         sdhci_writew(host, 0, SDHCI_CLOCK_CONTROL);
2039
2040         if (clock == 0)
2041                 return;
2042
2043         clk = sdhci_calc_clk(host, clock, &host->mmc->actual_clock);
2044         sdhci_enable_clk(host, clk);
2045 }
2046 EXPORT_SYMBOL_GPL(sdhci_set_clock);
2047
2048 static void sdhci_set_power_reg(struct sdhci_host *host, unsigned char mode,
2049                                 unsigned short vdd)
2050 {
2051         struct mmc_host *mmc = host->mmc;
2052
2053         mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, vdd);
2054
2055         if (mode != MMC_POWER_OFF)
2056                 sdhci_writeb(host, SDHCI_POWER_ON, SDHCI_POWER_CONTROL);
2057         else
2058                 sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
2059 }
2060
2061 void sdhci_set_power_noreg(struct sdhci_host *host, unsigned char mode,
2062                            unsigned short vdd)
2063 {
2064         u8 pwr = 0;
2065
2066         if (mode != MMC_POWER_OFF) {
2067                 switch (1 << vdd) {
2068                 case MMC_VDD_165_195:
2069                 /*
2070                  * Without a regulator, SDHCI does not support 2.0v
2071                  * so we only get here if the driver deliberately
2072                  * added the 2.0v range to ocr_avail. Map it to 1.8v
2073                  * for the purpose of turning on the power.
2074                  */
2075                 case MMC_VDD_20_21:
2076                         pwr = SDHCI_POWER_180;
2077                         break;
2078                 case MMC_VDD_29_30:
2079                 case MMC_VDD_30_31:
2080                         pwr = SDHCI_POWER_300;
2081                         break;
2082                 case MMC_VDD_32_33:
2083                 case MMC_VDD_33_34:
2084                 /*
2085                  * 3.4 ~ 3.6V are valid only for those platforms where it's
2086                  * known that the voltage range is supported by hardware.
2087                  */
2088                 case MMC_VDD_34_35:
2089                 case MMC_VDD_35_36:
2090                         pwr = SDHCI_POWER_330;
2091                         break;
2092                 default:
2093                         WARN(1, "%s: Invalid vdd %#x\n",
2094                              mmc_hostname(host->mmc), vdd);
2095                         break;
2096                 }
2097         }
2098
2099         if (host->pwr == pwr)
2100                 return;
2101
2102         host->pwr = pwr;
2103
2104         if (pwr == 0) {
2105                 sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
2106                 if (host->quirks2 & SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON)
2107                         sdhci_runtime_pm_bus_off(host);
2108         } else {
2109                 /*
2110                  * Spec says that we should clear the power reg before setting
2111                  * a new value. Some controllers don't seem to like this though.
2112                  */
2113                 if (!(host->quirks & SDHCI_QUIRK_SINGLE_POWER_WRITE))
2114                         sdhci_writeb(host, 0, SDHCI_POWER_CONTROL);
2115
2116                 /*
2117                  * At least the Marvell CaFe chip gets confused if we set the
2118                  * voltage and set turn on power at the same time, so set the
2119                  * voltage first.
2120                  */
2121                 if (host->quirks & SDHCI_QUIRK_NO_SIMULT_VDD_AND_POWER)
2122                         sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
2123
2124                 pwr |= SDHCI_POWER_ON;
2125
2126                 sdhci_writeb(host, pwr, SDHCI_POWER_CONTROL);
2127
2128                 if (host->quirks2 & SDHCI_QUIRK2_CARD_ON_NEEDS_BUS_ON)
2129                         sdhci_runtime_pm_bus_on(host);
2130
2131                 /*
2132                  * Some controllers need an extra 10ms delay of 10ms before
2133                  * they can apply clock after applying power
2134                  */
2135                 if (host->quirks & SDHCI_QUIRK_DELAY_AFTER_POWER)
2136                         mdelay(10);
2137         }
2138 }
2139 EXPORT_SYMBOL_GPL(sdhci_set_power_noreg);
2140
2141 void sdhci_set_power(struct sdhci_host *host, unsigned char mode,
2142                      unsigned short vdd)
2143 {
2144         if (IS_ERR(host->mmc->supply.vmmc))
2145                 sdhci_set_power_noreg(host, mode, vdd);
2146         else
2147                 sdhci_set_power_reg(host, mode, vdd);
2148 }
2149 EXPORT_SYMBOL_GPL(sdhci_set_power);
2150
2151 /*
2152  * Some controllers need to configure a valid bus voltage on their power
2153  * register regardless of whether an external regulator is taking care of power
2154  * supply. This helper function takes care of it if set as the controller's
2155  * sdhci_ops.set_power callback.
2156  */
2157 void sdhci_set_power_and_bus_voltage(struct sdhci_host *host,
2158                                      unsigned char mode,
2159                                      unsigned short vdd)
2160 {
2161         if (!IS_ERR(host->mmc->supply.vmmc)) {
2162                 struct mmc_host *mmc = host->mmc;
2163
2164                 mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, vdd);
2165         }
2166         sdhci_set_power_noreg(host, mode, vdd);
2167 }
2168 EXPORT_SYMBOL_GPL(sdhci_set_power_and_bus_voltage);
2169
2170 /*****************************************************************************\
2171  *                                                                           *
2172  * MMC callbacks                                                             *
2173  *                                                                           *
2174 \*****************************************************************************/
2175
2176 void sdhci_request(struct mmc_host *mmc, struct mmc_request *mrq)
2177 {
2178         struct sdhci_host *host = mmc_priv(mmc);
2179         struct mmc_command *cmd;
2180         unsigned long flags;
2181         bool present;
2182
2183         /* Firstly check card presence */
2184         present = mmc->ops->get_cd(mmc);
2185
2186         spin_lock_irqsave(&host->lock, flags);
2187
2188         sdhci_led_activate(host);
2189
2190         if (sdhci_present_error(host, mrq->cmd, present))
2191                 goto out_finish;
2192
2193         cmd = sdhci_manual_cmd23(host, mrq) ? mrq->sbc : mrq->cmd;
2194
2195         if (!sdhci_send_command_retry(host, cmd, flags))
2196                 goto out_finish;
2197
2198         spin_unlock_irqrestore(&host->lock, flags);
2199
2200         return;
2201
2202 out_finish:
2203         sdhci_finish_mrq(host, mrq);
2204         spin_unlock_irqrestore(&host->lock, flags);
2205 }
2206 EXPORT_SYMBOL_GPL(sdhci_request);
2207
2208 int sdhci_request_atomic(struct mmc_host *mmc, struct mmc_request *mrq)
2209 {
2210         struct sdhci_host *host = mmc_priv(mmc);
2211         struct mmc_command *cmd;
2212         unsigned long flags;
2213         int ret = 0;
2214
2215         spin_lock_irqsave(&host->lock, flags);
2216
2217         if (sdhci_present_error(host, mrq->cmd, true)) {
2218                 sdhci_finish_mrq(host, mrq);
2219                 goto out_finish;
2220         }
2221
2222         cmd = sdhci_manual_cmd23(host, mrq) ? mrq->sbc : mrq->cmd;
2223
2224         /*
2225          * The HSQ may send a command in interrupt context without polling
2226          * the busy signaling, which means we should return BUSY if controller
2227          * has not released inhibit bits to allow HSQ trying to send request
2228          * again in non-atomic context. So we should not finish this request
2229          * here.
2230          */
2231         if (!sdhci_send_command(host, cmd))
2232                 ret = -EBUSY;
2233         else
2234                 sdhci_led_activate(host);
2235
2236 out_finish:
2237         spin_unlock_irqrestore(&host->lock, flags);
2238         return ret;
2239 }
2240 EXPORT_SYMBOL_GPL(sdhci_request_atomic);
2241
2242 void sdhci_set_bus_width(struct sdhci_host *host, int width)
2243 {
2244         u8 ctrl;
2245
2246         ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
2247         if (width == MMC_BUS_WIDTH_8) {
2248                 ctrl &= ~SDHCI_CTRL_4BITBUS;
2249                 ctrl |= SDHCI_CTRL_8BITBUS;
2250         } else {
2251                 if (host->mmc->caps & MMC_CAP_8_BIT_DATA)
2252                         ctrl &= ~SDHCI_CTRL_8BITBUS;
2253                 if (width == MMC_BUS_WIDTH_4)
2254                         ctrl |= SDHCI_CTRL_4BITBUS;
2255                 else
2256                         ctrl &= ~SDHCI_CTRL_4BITBUS;
2257         }
2258         sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
2259 }
2260 EXPORT_SYMBOL_GPL(sdhci_set_bus_width);
2261
2262 void sdhci_set_uhs_signaling(struct sdhci_host *host, unsigned timing)
2263 {
2264         u16 ctrl_2;
2265
2266         ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
2267         /* Select Bus Speed Mode for host */
2268         ctrl_2 &= ~SDHCI_CTRL_UHS_MASK;
2269         if ((timing == MMC_TIMING_MMC_HS200) ||
2270             (timing == MMC_TIMING_UHS_SDR104))
2271                 ctrl_2 |= SDHCI_CTRL_UHS_SDR104;
2272         else if (timing == MMC_TIMING_UHS_SDR12)
2273                 ctrl_2 |= SDHCI_CTRL_UHS_SDR12;
2274         else if (timing == MMC_TIMING_UHS_SDR25)
2275                 ctrl_2 |= SDHCI_CTRL_UHS_SDR25;
2276         else if (timing == MMC_TIMING_UHS_SDR50)
2277                 ctrl_2 |= SDHCI_CTRL_UHS_SDR50;
2278         else if ((timing == MMC_TIMING_UHS_DDR50) ||
2279                  (timing == MMC_TIMING_MMC_DDR52))
2280                 ctrl_2 |= SDHCI_CTRL_UHS_DDR50;
2281         else if (timing == MMC_TIMING_MMC_HS400)
2282                 ctrl_2 |= SDHCI_CTRL_HS400; /* Non-standard */
2283         sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
2284 }
2285 EXPORT_SYMBOL_GPL(sdhci_set_uhs_signaling);
2286
2287 static bool sdhci_timing_has_preset(unsigned char timing)
2288 {
2289         switch (timing) {
2290         case MMC_TIMING_UHS_SDR12:
2291         case MMC_TIMING_UHS_SDR25:
2292         case MMC_TIMING_UHS_SDR50:
2293         case MMC_TIMING_UHS_SDR104:
2294         case MMC_TIMING_UHS_DDR50:
2295         case MMC_TIMING_MMC_DDR52:
2296                 return true;
2297         }
2298         return false;
2299 }
2300
2301 static bool sdhci_preset_needed(struct sdhci_host *host, unsigned char timing)
2302 {
2303         return !(host->quirks2 & SDHCI_QUIRK2_PRESET_VALUE_BROKEN) &&
2304                sdhci_timing_has_preset(timing);
2305 }
2306
2307 static bool sdhci_presetable_values_change(struct sdhci_host *host, struct mmc_ios *ios)
2308 {
2309         /*
2310          * Preset Values are: Driver Strength, Clock Generator and SDCLK/RCLK
2311          * Frequency. Check if preset values need to be enabled, or the Driver
2312          * Strength needs updating. Note, clock changes are handled separately.
2313          */
2314         return !host->preset_enabled &&
2315                (sdhci_preset_needed(host, ios->timing) || host->drv_type != ios->drv_type);
2316 }
2317
2318 void sdhci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
2319 {
2320         struct sdhci_host *host = mmc_priv(mmc);
2321         bool reinit_uhs = host->reinit_uhs;
2322         bool turning_on_clk = false;
2323         u8 ctrl;
2324
2325         host->reinit_uhs = false;
2326
2327         if (ios->power_mode == MMC_POWER_UNDEFINED)
2328                 return;
2329
2330         if (host->flags & SDHCI_DEVICE_DEAD) {
2331                 if (!IS_ERR(mmc->supply.vmmc) &&
2332                     ios->power_mode == MMC_POWER_OFF)
2333                         mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0);
2334                 return;
2335         }
2336
2337         /*
2338          * Reset the chip on each power off.
2339          * Should clear out any weird states.
2340          */
2341         if (ios->power_mode == MMC_POWER_OFF) {
2342                 sdhci_writel(host, 0, SDHCI_SIGNAL_ENABLE);
2343                 sdhci_reinit(host);
2344         }
2345
2346         if (host->version >= SDHCI_SPEC_300 &&
2347                 (ios->power_mode == MMC_POWER_UP) &&
2348                 !(host->quirks2 & SDHCI_QUIRK2_PRESET_VALUE_BROKEN))
2349                 sdhci_enable_preset_value(host, false);
2350
2351         if (!ios->clock || ios->clock != host->clock) {
2352                 turning_on_clk = ios->clock && !host->clock;
2353
2354                 host->ops->set_clock(host, ios->clock);
2355                 host->clock = ios->clock;
2356
2357                 if (host->quirks & SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK &&
2358                     host->clock) {
2359                         host->timeout_clk = mmc->actual_clock ?
2360                                                 mmc->actual_clock / 1000 :
2361                                                 host->clock / 1000;
2362                         mmc->max_busy_timeout =
2363                                 host->ops->get_max_timeout_count ?
2364                                 host->ops->get_max_timeout_count(host) :
2365                                 1 << 27;
2366                         mmc->max_busy_timeout /= host->timeout_clk;
2367                 }
2368         }
2369
2370         if (host->ops->set_power)
2371                 host->ops->set_power(host, ios->power_mode, ios->vdd);
2372         else
2373                 sdhci_set_power(host, ios->power_mode, ios->vdd);
2374
2375         if (host->ops->platform_send_init_74_clocks)
2376                 host->ops->platform_send_init_74_clocks(host, ios->power_mode);
2377
2378         host->ops->set_bus_width(host, ios->bus_width);
2379
2380         /*
2381          * Special case to avoid multiple clock changes during voltage
2382          * switching.
2383          */
2384         if (!reinit_uhs &&
2385             turning_on_clk &&
2386             host->timing == ios->timing &&
2387             host->version >= SDHCI_SPEC_300 &&
2388             !sdhci_presetable_values_change(host, ios))
2389                 return;
2390
2391         ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
2392
2393         if (!(host->quirks & SDHCI_QUIRK_NO_HISPD_BIT)) {
2394                 if (ios->timing == MMC_TIMING_SD_HS ||
2395                      ios->timing == MMC_TIMING_MMC_HS ||
2396                      ios->timing == MMC_TIMING_MMC_HS400 ||
2397                      ios->timing == MMC_TIMING_MMC_HS200 ||
2398                      ios->timing == MMC_TIMING_MMC_DDR52 ||
2399                      ios->timing == MMC_TIMING_UHS_SDR50 ||
2400                      ios->timing == MMC_TIMING_UHS_SDR104 ||
2401                      ios->timing == MMC_TIMING_UHS_DDR50 ||
2402                      ios->timing == MMC_TIMING_UHS_SDR25)
2403                         ctrl |= SDHCI_CTRL_HISPD;
2404                 else
2405                         ctrl &= ~SDHCI_CTRL_HISPD;
2406         }
2407
2408         if (host->version >= SDHCI_SPEC_300) {
2409                 u16 clk, ctrl_2;
2410
2411                 /*
2412                  * According to SDHCI Spec v3.00, if the Preset Value
2413                  * Enable in the Host Control 2 register is set, we
2414                  * need to reset SD Clock Enable before changing High
2415                  * Speed Enable to avoid generating clock glitches.
2416                  */
2417                 clk = sdhci_readw(host, SDHCI_CLOCK_CONTROL);
2418                 if (clk & SDHCI_CLOCK_CARD_EN) {
2419                         clk &= ~SDHCI_CLOCK_CARD_EN;
2420                         sdhci_writew(host, clk, SDHCI_CLOCK_CONTROL);
2421                 }
2422
2423                 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
2424
2425                 if (!host->preset_enabled) {
2426                         /*
2427                          * We only need to set Driver Strength if the
2428                          * preset value enable is not set.
2429                          */
2430                         ctrl_2 = sdhci_readw(host, SDHCI_HOST_CONTROL2);
2431                         ctrl_2 &= ~SDHCI_CTRL_DRV_TYPE_MASK;
2432                         if (ios->drv_type == MMC_SET_DRIVER_TYPE_A)
2433                                 ctrl_2 |= SDHCI_CTRL_DRV_TYPE_A;
2434                         else if (ios->drv_type == MMC_SET_DRIVER_TYPE_B)
2435                                 ctrl_2 |= SDHCI_CTRL_DRV_TYPE_B;
2436                         else if (ios->drv_type == MMC_SET_DRIVER_TYPE_C)
2437                                 ctrl_2 |= SDHCI_CTRL_DRV_TYPE_C;
2438                         else if (ios->drv_type == MMC_SET_DRIVER_TYPE_D)
2439                                 ctrl_2 |= SDHCI_CTRL_DRV_TYPE_D;
2440                         else {
2441                                 pr_warn("%s: invalid driver type, default to driver type B\n",
2442                                         mmc_hostname(mmc));
2443                                 ctrl_2 |= SDHCI_CTRL_DRV_TYPE_B;
2444                         }
2445
2446                         sdhci_writew(host, ctrl_2, SDHCI_HOST_CONTROL2);
2447                         host->drv_type = ios->drv_type;
2448                 }
2449
2450                 host->ops->set_uhs_signaling(host, ios->timing);
2451                 host->timing = ios->timing;
2452
2453                 if (sdhci_preset_needed(host, ios->timing)) {
2454                         u16 preset;
2455
2456                         sdhci_enable_preset_value(host, true);
2457                         preset = sdhci_get_preset_value(host);
2458                         ios->drv_type = FIELD_GET(SDHCI_PRESET_DRV_MASK,
2459                                                   preset);
2460                         host->drv_type = ios->drv_type;
2461                 }
2462
2463                 /* Re-enable SD Clock */
2464                 host->ops->set_clock(host, host->clock);
2465         } else
2466                 sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
2467 }
2468 EXPORT_SYMBOL_GPL(sdhci_set_ios);
2469
2470 static int sdhci_get_cd(struct mmc_host *mmc)
2471 {
2472         struct sdhci_host *host = mmc_priv(mmc);
2473         int gpio_cd = mmc_gpio_get_cd(mmc);
2474
2475         if (host->flags & SDHCI_DEVICE_DEAD)
2476                 return 0;
2477
2478         /* If nonremovable, assume that the card is always present. */
2479         if (!mmc_card_is_removable(mmc))
2480                 return 1;
2481
2482         /*
2483          * Try slot gpio detect, if defined it take precedence
2484          * over build in controller functionality
2485          */
2486         if (gpio_cd >= 0)
2487                 return !!gpio_cd;
2488
2489         /* If polling, assume that the card is always present. */
2490         if (host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION)
2491                 return 1;
2492
2493         /* Host native card detect */
2494         return !!(sdhci_readl(host, SDHCI_PRESENT_STATE) & SDHCI_CARD_PRESENT);
2495 }
2496
2497 int sdhci_get_cd_nogpio(struct mmc_host *mmc)
2498 {
2499         struct sdhci_host *host = mmc_priv(mmc);
2500         unsigned long flags;
2501         int ret = 0;
2502
2503         spin_lock_irqsave(&host->lock, flags);
2504
2505         if (host->flags & SDHCI_DEVICE_DEAD)
2506                 goto out;
2507
2508         ret = !!(sdhci_readl(host, SDHCI_PRESENT_STATE) & SDHCI_CARD_PRESENT);
2509 out:
2510         spin_unlock_irqrestore(&host->lock, flags);
2511
2512         return ret;
2513 }
2514 EXPORT_SYMBOL_GPL(sdhci_get_cd_nogpio);
2515
2516 static int sdhci_check_ro(struct sdhci_host *host)
2517 {
2518         unsigned long flags;
2519         int is_readonly;
2520
2521         spin_lock_irqsave(&host->lock, flags);
2522
2523         if (host->flags & SDHCI_DEVICE_DEAD)
2524                 is_readonly = 0;
2525         else if (host->ops->get_ro)
2526                 is_readonly = host->ops->get_ro(host);
2527         else if (mmc_can_gpio_ro(host->mmc))
2528                 is_readonly = mmc_gpio_get_ro(host->mmc);
2529         else
2530                 is_readonly = !(sdhci_readl(host, SDHCI_PRESENT_STATE)
2531                                 & SDHCI_WRITE_PROTECT);
2532
2533         spin_unlock_irqrestore(&host->lock, flags);
2534
2535         /* This quirk needs to be replaced by a callback-function later */
2536         return host->quirks & SDHCI_QUIRK_INVERTED_WRITE_PROTECT ?
2537                 !is_readonly : is_readonly;
2538 }
2539
2540 #define SAMPLE_COUNT    5
2541
2542 static int sdhci_get_ro(struct mmc_host *mmc)
2543 {
2544         struct sdhci_host *host = mmc_priv(mmc);
2545         int i, ro_count;
2546
2547         if (!(host->quirks & SDHCI_QUIRK_UNSTABLE_RO_DETECT))
2548                 return sdhci_check_ro(host);
2549
2550         ro_count = 0;
2551         for (i = 0; i < SAMPLE_COUNT; i++) {
2552                 if (sdhci_check_ro(host)) {
2553                         if (++ro_count > SAMPLE_COUNT / 2)
2554                                 return 1;
2555                 }
2556                 msleep(30);
2557         }
2558         return 0;
2559 }
2560
2561 static void sdhci_hw_reset(struct mmc_host *mmc)
2562 {
2563         struct sdhci_host *host = mmc_priv(mmc);
2564
2565         if (host->ops && host->ops->hw_reset)
2566                 host->ops->hw_reset(host);
2567 }
2568
2569 static void sdhci_enable_sdio_irq_nolock(struct sdhci_host *host, int enable)
2570 {
2571         if (!(host->flags & SDHCI_DEVICE_DEAD)) {
2572                 if (enable)
2573                         host->ier |= SDHCI_INT_CARD_INT;
2574                 else
2575                         host->ier &= ~SDHCI_INT_CARD_INT;
2576
2577                 sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
2578                 sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
2579         }
2580 }
2581
2582 void sdhci_enable_sdio_irq(struct mmc_host *mmc, int enable)
2583 {
2584         struct sdhci_host *host = mmc_priv(mmc);
2585         unsigned long flags;
2586
2587         if (enable)
2588                 pm_runtime_get_noresume(mmc_dev(mmc));
2589
2590         spin_lock_irqsave(&host->lock, flags);
2591         sdhci_enable_sdio_irq_nolock(host, enable);
2592         spin_unlock_irqrestore(&host->lock, flags);
2593
2594         if (!enable)
2595                 pm_runtime_put_noidle(mmc_dev(mmc));
2596 }
2597 EXPORT_SYMBOL_GPL(sdhci_enable_sdio_irq);
2598
2599 static void sdhci_ack_sdio_irq(struct mmc_host *mmc)
2600 {
2601         struct sdhci_host *host = mmc_priv(mmc);
2602         unsigned long flags;
2603
2604         spin_lock_irqsave(&host->lock, flags);
2605         sdhci_enable_sdio_irq_nolock(host, true);
2606         spin_unlock_irqrestore(&host->lock, flags);
2607 }
2608
2609 int sdhci_start_signal_voltage_switch(struct mmc_host *mmc,
2610                                       struct mmc_ios *ios)
2611 {
2612         struct sdhci_host *host = mmc_priv(mmc);
2613         u16 ctrl;
2614         int ret;
2615
2616         /*
2617          * Signal Voltage Switching is only applicable for Host Controllers
2618          * v3.00 and above.
2619          */
2620         if (host->version < SDHCI_SPEC_300)
2621                 return 0;
2622
2623         ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
2624
2625         switch (ios->signal_voltage) {
2626         case MMC_SIGNAL_VOLTAGE_330:
2627                 if (!(host->flags & SDHCI_SIGNALING_330))
2628                         return -EINVAL;
2629                 /* Set 1.8V Signal Enable in the Host Control2 register to 0 */
2630                 ctrl &= ~SDHCI_CTRL_VDD_180;
2631                 sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
2632
2633                 if (!IS_ERR(mmc->supply.vqmmc)) {
2634                         ret = mmc_regulator_set_vqmmc(mmc, ios);
2635                         if (ret < 0) {
2636                                 pr_warn("%s: Switching to 3.3V signalling voltage failed\n",
2637                                         mmc_hostname(mmc));
2638                                 return -EIO;
2639                         }
2640                 }
2641                 /* Wait for 5ms */
2642                 usleep_range(5000, 5500);
2643
2644                 /* 3.3V regulator output should be stable within 5 ms */
2645                 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
2646                 if (!(ctrl & SDHCI_CTRL_VDD_180))
2647                         return 0;
2648
2649                 pr_warn("%s: 3.3V regulator output did not become stable\n",
2650                         mmc_hostname(mmc));
2651
2652                 return -EAGAIN;
2653         case MMC_SIGNAL_VOLTAGE_180:
2654                 if (!(host->flags & SDHCI_SIGNALING_180))
2655                         return -EINVAL;
2656                 if (!IS_ERR(mmc->supply.vqmmc)) {
2657                         ret = mmc_regulator_set_vqmmc(mmc, ios);
2658                         if (ret < 0) {
2659                                 pr_warn("%s: Switching to 1.8V signalling voltage failed\n",
2660                                         mmc_hostname(mmc));
2661                                 return -EIO;
2662                         }
2663                 }
2664
2665                 /*
2666                  * Enable 1.8V Signal Enable in the Host Control2
2667                  * register
2668                  */
2669                 ctrl |= SDHCI_CTRL_VDD_180;
2670                 sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
2671
2672                 /* Some controller need to do more when switching */
2673                 if (host->ops->voltage_switch)
2674                         host->ops->voltage_switch(host);
2675
2676                 /* 1.8V regulator output should be stable within 5 ms */
2677                 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
2678                 if (ctrl & SDHCI_CTRL_VDD_180)
2679                         return 0;
2680
2681                 pr_warn("%s: 1.8V regulator output did not become stable\n",
2682                         mmc_hostname(mmc));
2683
2684                 return -EAGAIN;
2685         case MMC_SIGNAL_VOLTAGE_120:
2686                 if (!(host->flags & SDHCI_SIGNALING_120))
2687                         return -EINVAL;
2688                 if (!IS_ERR(mmc->supply.vqmmc)) {
2689                         ret = mmc_regulator_set_vqmmc(mmc, ios);
2690                         if (ret < 0) {
2691                                 pr_warn("%s: Switching to 1.2V signalling voltage failed\n",
2692                                         mmc_hostname(mmc));
2693                                 return -EIO;
2694                         }
2695                 }
2696                 return 0;
2697         default:
2698                 /* No signal voltage switch required */
2699                 return 0;
2700         }
2701 }
2702 EXPORT_SYMBOL_GPL(sdhci_start_signal_voltage_switch);
2703
2704 static int sdhci_card_busy(struct mmc_host *mmc)
2705 {
2706         struct sdhci_host *host = mmc_priv(mmc);
2707         u32 present_state;
2708
2709         /* Check whether DAT[0] is 0 */
2710         present_state = sdhci_readl(host, SDHCI_PRESENT_STATE);
2711
2712         return !(present_state & SDHCI_DATA_0_LVL_MASK);
2713 }
2714
2715 static int sdhci_prepare_hs400_tuning(struct mmc_host *mmc, struct mmc_ios *ios)
2716 {
2717         struct sdhci_host *host = mmc_priv(mmc);
2718         unsigned long flags;
2719
2720         spin_lock_irqsave(&host->lock, flags);
2721         host->flags |= SDHCI_HS400_TUNING;
2722         spin_unlock_irqrestore(&host->lock, flags);
2723
2724         return 0;
2725 }
2726
2727 void sdhci_start_tuning(struct sdhci_host *host)
2728 {
2729         u16 ctrl;
2730
2731         ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
2732         ctrl |= SDHCI_CTRL_EXEC_TUNING;
2733         if (host->quirks2 & SDHCI_QUIRK2_TUNING_WORK_AROUND)
2734                 ctrl |= SDHCI_CTRL_TUNED_CLK;
2735         sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
2736
2737         /*
2738          * As per the Host Controller spec v3.00, tuning command
2739          * generates Buffer Read Ready interrupt, so enable that.
2740          *
2741          * Note: The spec clearly says that when tuning sequence
2742          * is being performed, the controller does not generate
2743          * interrupts other than Buffer Read Ready interrupt. But
2744          * to make sure we don't hit a controller bug, we _only_
2745          * enable Buffer Read Ready interrupt here.
2746          */
2747         sdhci_writel(host, SDHCI_INT_DATA_AVAIL, SDHCI_INT_ENABLE);
2748         sdhci_writel(host, SDHCI_INT_DATA_AVAIL, SDHCI_SIGNAL_ENABLE);
2749 }
2750 EXPORT_SYMBOL_GPL(sdhci_start_tuning);
2751
2752 void sdhci_end_tuning(struct sdhci_host *host)
2753 {
2754         sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
2755         sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
2756 }
2757 EXPORT_SYMBOL_GPL(sdhci_end_tuning);
2758
2759 void sdhci_reset_tuning(struct sdhci_host *host)
2760 {
2761         u16 ctrl;
2762
2763         ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
2764         ctrl &= ~SDHCI_CTRL_TUNED_CLK;
2765         ctrl &= ~SDHCI_CTRL_EXEC_TUNING;
2766         sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
2767 }
2768 EXPORT_SYMBOL_GPL(sdhci_reset_tuning);
2769
2770 void sdhci_abort_tuning(struct sdhci_host *host, u32 opcode)
2771 {
2772         sdhci_reset_tuning(host);
2773
2774         sdhci_reset_for(host, TUNING_ABORT);
2775
2776         sdhci_end_tuning(host);
2777
2778         mmc_send_abort_tuning(host->mmc, opcode);
2779 }
2780 EXPORT_SYMBOL_GPL(sdhci_abort_tuning);
2781
2782 /*
2783  * We use sdhci_send_tuning() because mmc_send_tuning() is not a good fit. SDHCI
2784  * tuning command does not have a data payload (or rather the hardware does it
2785  * automatically) so mmc_send_tuning() will return -EIO. Also the tuning command
2786  * interrupt setup is different to other commands and there is no timeout
2787  * interrupt so special handling is needed.
2788  */
2789 void sdhci_send_tuning(struct sdhci_host *host, u32 opcode)
2790 {
2791         struct mmc_host *mmc = host->mmc;
2792         struct mmc_command cmd = {};
2793         struct mmc_request mrq = {};
2794         unsigned long flags;
2795         u32 b = host->sdma_boundary;
2796
2797         spin_lock_irqsave(&host->lock, flags);
2798
2799         cmd.opcode = opcode;
2800         cmd.flags = MMC_RSP_R1 | MMC_CMD_ADTC;
2801         cmd.mrq = &mrq;
2802
2803         mrq.cmd = &cmd;
2804         /*
2805          * In response to CMD19, the card sends 64 bytes of tuning
2806          * block to the Host Controller. So we set the block size
2807          * to 64 here.
2808          */
2809         if (cmd.opcode == MMC_SEND_TUNING_BLOCK_HS200 &&
2810             mmc->ios.bus_width == MMC_BUS_WIDTH_8)
2811                 sdhci_writew(host, SDHCI_MAKE_BLKSZ(b, 128), SDHCI_BLOCK_SIZE);
2812         else
2813                 sdhci_writew(host, SDHCI_MAKE_BLKSZ(b, 64), SDHCI_BLOCK_SIZE);
2814
2815         /*
2816          * The tuning block is sent by the card to the host controller.
2817          * So we set the TRNS_READ bit in the Transfer Mode register.
2818          * This also takes care of setting DMA Enable and Multi Block
2819          * Select in the same register to 0.
2820          */
2821         sdhci_writew(host, SDHCI_TRNS_READ, SDHCI_TRANSFER_MODE);
2822
2823         if (!sdhci_send_command_retry(host, &cmd, flags)) {
2824                 spin_unlock_irqrestore(&host->lock, flags);
2825                 host->tuning_done = 0;
2826                 return;
2827         }
2828
2829         host->cmd = NULL;
2830
2831         sdhci_del_timer(host, &mrq);
2832
2833         host->tuning_done = 0;
2834
2835         spin_unlock_irqrestore(&host->lock, flags);
2836
2837         /* Wait for Buffer Read Ready interrupt */
2838         wait_event_timeout(host->buf_ready_int, (host->tuning_done == 1),
2839                            msecs_to_jiffies(50));
2840
2841 }
2842 EXPORT_SYMBOL_GPL(sdhci_send_tuning);
2843
2844 int __sdhci_execute_tuning(struct sdhci_host *host, u32 opcode)
2845 {
2846         int i;
2847
2848         /*
2849          * Issue opcode repeatedly till Execute Tuning is set to 0 or the number
2850          * of loops reaches tuning loop count.
2851          */
2852         for (i = 0; i < host->tuning_loop_count; i++) {
2853                 u16 ctrl;
2854
2855                 sdhci_send_tuning(host, opcode);
2856
2857                 if (!host->tuning_done) {
2858                         pr_debug("%s: Tuning timeout, falling back to fixed sampling clock\n",
2859                                  mmc_hostname(host->mmc));
2860                         sdhci_abort_tuning(host, opcode);
2861                         return -ETIMEDOUT;
2862                 }
2863
2864                 /* Spec does not require a delay between tuning cycles */
2865                 if (host->tuning_delay > 0)
2866                         mdelay(host->tuning_delay);
2867
2868                 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
2869                 if (!(ctrl & SDHCI_CTRL_EXEC_TUNING)) {
2870                         if (ctrl & SDHCI_CTRL_TUNED_CLK)
2871                                 return 0; /* Success! */
2872                         break;
2873                 }
2874
2875         }
2876
2877         pr_info("%s: Tuning failed, falling back to fixed sampling clock\n",
2878                 mmc_hostname(host->mmc));
2879         sdhci_reset_tuning(host);
2880         return -EAGAIN;
2881 }
2882 EXPORT_SYMBOL_GPL(__sdhci_execute_tuning);
2883
2884 int sdhci_execute_tuning(struct mmc_host *mmc, u32 opcode)
2885 {
2886         struct sdhci_host *host = mmc_priv(mmc);
2887         int err = 0;
2888         unsigned int tuning_count = 0;
2889         bool hs400_tuning;
2890
2891         hs400_tuning = host->flags & SDHCI_HS400_TUNING;
2892
2893         if (host->tuning_mode == SDHCI_TUNING_MODE_1)
2894                 tuning_count = host->tuning_count;
2895
2896         /*
2897          * The Host Controller needs tuning in case of SDR104 and DDR50
2898          * mode, and for SDR50 mode when Use Tuning for SDR50 is set in
2899          * the Capabilities register.
2900          * If the Host Controller supports the HS200 mode then the
2901          * tuning function has to be executed.
2902          */
2903         switch (host->timing) {
2904         /* HS400 tuning is done in HS200 mode */
2905         case MMC_TIMING_MMC_HS400:
2906                 err = -EINVAL;
2907                 goto out;
2908
2909         case MMC_TIMING_MMC_HS200:
2910                 /*
2911                  * Periodic re-tuning for HS400 is not expected to be needed, so
2912                  * disable it here.
2913                  */
2914                 if (hs400_tuning)
2915                         tuning_count = 0;
2916                 break;
2917
2918         case MMC_TIMING_UHS_SDR104:
2919         case MMC_TIMING_UHS_DDR50:
2920                 break;
2921
2922         case MMC_TIMING_UHS_SDR50:
2923                 if (host->flags & SDHCI_SDR50_NEEDS_TUNING)
2924                         break;
2925                 fallthrough;
2926
2927         default:
2928                 goto out;
2929         }
2930
2931         if (host->ops->platform_execute_tuning) {
2932                 err = host->ops->platform_execute_tuning(host, opcode);
2933                 goto out;
2934         }
2935
2936         mmc->retune_period = tuning_count;
2937
2938         if (host->tuning_delay < 0)
2939                 host->tuning_delay = opcode == MMC_SEND_TUNING_BLOCK;
2940
2941         sdhci_start_tuning(host);
2942
2943         host->tuning_err = __sdhci_execute_tuning(host, opcode);
2944
2945         sdhci_end_tuning(host);
2946 out:
2947         host->flags &= ~SDHCI_HS400_TUNING;
2948
2949         return err;
2950 }
2951 EXPORT_SYMBOL_GPL(sdhci_execute_tuning);
2952
2953 static void sdhci_enable_preset_value(struct sdhci_host *host, bool enable)
2954 {
2955         /* Host Controller v3.00 defines preset value registers */
2956         if (host->version < SDHCI_SPEC_300)
2957                 return;
2958
2959         /*
2960          * We only enable or disable Preset Value if they are not already
2961          * enabled or disabled respectively. Otherwise, we bail out.
2962          */
2963         if (host->preset_enabled != enable) {
2964                 u16 ctrl = sdhci_readw(host, SDHCI_HOST_CONTROL2);
2965
2966                 if (enable)
2967                         ctrl |= SDHCI_CTRL_PRESET_VAL_ENABLE;
2968                 else
2969                         ctrl &= ~SDHCI_CTRL_PRESET_VAL_ENABLE;
2970
2971                 sdhci_writew(host, ctrl, SDHCI_HOST_CONTROL2);
2972
2973                 if (enable)
2974                         host->flags |= SDHCI_PV_ENABLED;
2975                 else
2976                         host->flags &= ~SDHCI_PV_ENABLED;
2977
2978                 host->preset_enabled = enable;
2979         }
2980 }
2981
2982 static void sdhci_post_req(struct mmc_host *mmc, struct mmc_request *mrq,
2983                                 int err)
2984 {
2985         struct mmc_data *data = mrq->data;
2986
2987         if (data->host_cookie != COOKIE_UNMAPPED)
2988                 dma_unmap_sg(mmc_dev(mmc), data->sg, data->sg_len,
2989                              mmc_get_dma_dir(data));
2990
2991         data->host_cookie = COOKIE_UNMAPPED;
2992 }
2993
2994 static void sdhci_pre_req(struct mmc_host *mmc, struct mmc_request *mrq)
2995 {
2996         struct sdhci_host *host = mmc_priv(mmc);
2997
2998         mrq->data->host_cookie = COOKIE_UNMAPPED;
2999
3000         /*
3001          * No pre-mapping in the pre hook if we're using the bounce buffer,
3002          * for that we would need two bounce buffers since one buffer is
3003          * in flight when this is getting called.
3004          */
3005         if (host->flags & SDHCI_REQ_USE_DMA && !host->bounce_buffer)
3006                 sdhci_pre_dma_transfer(host, mrq->data, COOKIE_PRE_MAPPED);
3007 }
3008
3009 static void sdhci_error_out_mrqs(struct sdhci_host *host, int err)
3010 {
3011         if (host->data_cmd) {
3012                 host->data_cmd->error = err;
3013                 sdhci_finish_mrq(host, host->data_cmd->mrq);
3014         }
3015
3016         if (host->cmd) {
3017                 host->cmd->error = err;
3018                 sdhci_finish_mrq(host, host->cmd->mrq);
3019         }
3020 }
3021
3022 static void sdhci_card_event(struct mmc_host *mmc)
3023 {
3024         struct sdhci_host *host = mmc_priv(mmc);
3025         unsigned long flags;
3026         int present;
3027
3028         /* First check if client has provided their own card event */
3029         if (host->ops->card_event)
3030                 host->ops->card_event(host);
3031
3032         present = mmc->ops->get_cd(mmc);
3033
3034         spin_lock_irqsave(&host->lock, flags);
3035
3036         /* Check sdhci_has_requests() first in case we are runtime suspended */
3037         if (sdhci_has_requests(host) && !present) {
3038                 pr_err("%s: Card removed during transfer!\n",
3039                         mmc_hostname(mmc));
3040                 pr_err("%s: Resetting controller.\n",
3041                         mmc_hostname(mmc));
3042
3043                 sdhci_reset_for(host, CARD_REMOVED);
3044
3045                 sdhci_error_out_mrqs(host, -ENOMEDIUM);
3046         }
3047
3048         spin_unlock_irqrestore(&host->lock, flags);
3049 }
3050
3051 static const struct mmc_host_ops sdhci_ops = {
3052         .request        = sdhci_request,
3053         .post_req       = sdhci_post_req,
3054         .pre_req        = sdhci_pre_req,
3055         .set_ios        = sdhci_set_ios,
3056         .get_cd         = sdhci_get_cd,
3057         .get_ro         = sdhci_get_ro,
3058         .card_hw_reset  = sdhci_hw_reset,
3059         .enable_sdio_irq = sdhci_enable_sdio_irq,
3060         .ack_sdio_irq    = sdhci_ack_sdio_irq,
3061         .start_signal_voltage_switch    = sdhci_start_signal_voltage_switch,
3062         .prepare_hs400_tuning           = sdhci_prepare_hs400_tuning,
3063         .execute_tuning                 = sdhci_execute_tuning,
3064         .card_event                     = sdhci_card_event,
3065         .card_busy      = sdhci_card_busy,
3066 };
3067
3068 /*****************************************************************************\
3069  *                                                                           *
3070  * Request done                                                              *
3071  *                                                                           *
3072 \*****************************************************************************/
3073
3074 static bool sdhci_request_done(struct sdhci_host *host)
3075 {
3076         unsigned long flags;
3077         struct mmc_request *mrq;
3078         int i;
3079
3080         spin_lock_irqsave(&host->lock, flags);
3081
3082         for (i = 0; i < SDHCI_MAX_MRQS; i++) {
3083                 mrq = host->mrqs_done[i];
3084                 if (mrq)
3085                         break;
3086         }
3087
3088         if (!mrq) {
3089                 spin_unlock_irqrestore(&host->lock, flags);
3090                 return true;
3091         }
3092
3093         /*
3094          * The controller needs a reset of internal state machines
3095          * upon error conditions.
3096          */
3097         if (sdhci_needs_reset(host, mrq)) {
3098                 /*
3099                  * Do not finish until command and data lines are available for
3100                  * reset. Note there can only be one other mrq, so it cannot
3101                  * also be in mrqs_done, otherwise host->cmd and host->data_cmd
3102                  * would both be null.
3103                  */
3104                 if (host->cmd || host->data_cmd) {
3105                         spin_unlock_irqrestore(&host->lock, flags);
3106                         return true;
3107                 }
3108
3109                 /* Some controllers need this kick or reset won't work here */
3110                 if (host->quirks & SDHCI_QUIRK_CLOCK_BEFORE_RESET)
3111                         /* This is to force an update */
3112                         host->ops->set_clock(host, host->clock);
3113
3114                 sdhci_reset_for(host, REQUEST_ERROR);
3115
3116                 host->pending_reset = false;
3117         }
3118
3119         /*
3120          * Always unmap the data buffers if they were mapped by
3121          * sdhci_prepare_data() whenever we finish with a request.
3122          * This avoids leaking DMA mappings on error.
3123          */
3124         if (host->flags & SDHCI_REQ_USE_DMA) {
3125                 struct mmc_data *data = mrq->data;
3126
3127                 if (host->use_external_dma && data &&
3128                     (mrq->cmd->error || data->error)) {
3129                         struct dma_chan *chan = sdhci_external_dma_channel(host, data);
3130
3131                         host->mrqs_done[i] = NULL;
3132                         spin_unlock_irqrestore(&host->lock, flags);
3133                         dmaengine_terminate_sync(chan);
3134                         spin_lock_irqsave(&host->lock, flags);
3135                         sdhci_set_mrq_done(host, mrq);
3136                 }
3137
3138                 if (data && data->host_cookie == COOKIE_MAPPED) {
3139                         if (host->bounce_buffer) {
3140                                 /*
3141                                  * On reads, copy the bounced data into the
3142                                  * sglist
3143                                  */
3144                                 if (mmc_get_dma_dir(data) == DMA_FROM_DEVICE) {
3145                                         unsigned int length = data->bytes_xfered;
3146
3147                                         if (length > host->bounce_buffer_size) {
3148                                                 pr_err("%s: bounce buffer is %u bytes but DMA claims to have transferred %u bytes\n",
3149                                                        mmc_hostname(host->mmc),
3150                                                        host->bounce_buffer_size,
3151                                                        data->bytes_xfered);
3152                                                 /* Cap it down and continue */
3153                                                 length = host->bounce_buffer_size;
3154                                         }
3155                                         dma_sync_single_for_cpu(
3156                                                 mmc_dev(host->mmc),
3157                                                 host->bounce_addr,
3158                                                 host->bounce_buffer_size,
3159                                                 DMA_FROM_DEVICE);
3160                                         sg_copy_from_buffer(data->sg,
3161                                                 data->sg_len,
3162                                                 host->bounce_buffer,
3163                                                 length);
3164                                 } else {
3165                                         /* No copying, just switch ownership */
3166                                         dma_sync_single_for_cpu(
3167                                                 mmc_dev(host->mmc),
3168                                                 host->bounce_addr,
3169                                                 host->bounce_buffer_size,
3170                                                 mmc_get_dma_dir(data));
3171                                 }
3172                         } else {
3173                                 /* Unmap the raw data */
3174                                 dma_unmap_sg(mmc_dev(host->mmc), data->sg,
3175                                              data->sg_len,
3176                                              mmc_get_dma_dir(data));
3177                         }
3178                         data->host_cookie = COOKIE_UNMAPPED;
3179                 }
3180         }
3181
3182         host->mrqs_done[i] = NULL;
3183
3184         spin_unlock_irqrestore(&host->lock, flags);
3185
3186         if (host->ops->request_done)
3187                 host->ops->request_done(host, mrq);
3188         else
3189                 mmc_request_done(host->mmc, mrq);
3190
3191         return false;
3192 }
3193
3194 static void sdhci_complete_work(struct work_struct *work)
3195 {
3196         struct sdhci_host *host = container_of(work, struct sdhci_host,
3197                                                complete_work);
3198
3199         while (!sdhci_request_done(host))
3200                 ;
3201 }
3202
3203 static void sdhci_timeout_timer(struct timer_list *t)
3204 {
3205         struct sdhci_host *host;
3206         unsigned long flags;
3207
3208         host = from_timer(host, t, timer);
3209
3210         spin_lock_irqsave(&host->lock, flags);
3211
3212         if (host->cmd && !sdhci_data_line_cmd(host->cmd)) {
3213                 pr_err("%s: Timeout waiting for hardware cmd interrupt.\n",
3214                        mmc_hostname(host->mmc));
3215                 sdhci_err_stats_inc(host, REQ_TIMEOUT);
3216                 sdhci_dumpregs(host);
3217
3218                 host->cmd->error = -ETIMEDOUT;
3219                 sdhci_finish_mrq(host, host->cmd->mrq);
3220         }
3221
3222         spin_unlock_irqrestore(&host->lock, flags);
3223 }
3224
3225 static void sdhci_timeout_data_timer(struct timer_list *t)
3226 {
3227         struct sdhci_host *host;
3228         unsigned long flags;
3229
3230         host = from_timer(host, t, data_timer);
3231
3232         spin_lock_irqsave(&host->lock, flags);
3233
3234         if (host->data || host->data_cmd ||
3235             (host->cmd && sdhci_data_line_cmd(host->cmd))) {
3236                 pr_err("%s: Timeout waiting for hardware interrupt.\n",
3237                        mmc_hostname(host->mmc));
3238                 sdhci_err_stats_inc(host, REQ_TIMEOUT);
3239                 sdhci_dumpregs(host);
3240
3241                 if (host->data) {
3242                         host->data->error = -ETIMEDOUT;
3243                         __sdhci_finish_data(host, true);
3244                         queue_work(host->complete_wq, &host->complete_work);
3245                 } else if (host->data_cmd) {
3246                         host->data_cmd->error = -ETIMEDOUT;
3247                         sdhci_finish_mrq(host, host->data_cmd->mrq);
3248                 } else {
3249                         host->cmd->error = -ETIMEDOUT;
3250                         sdhci_finish_mrq(host, host->cmd->mrq);
3251                 }
3252         }
3253
3254         spin_unlock_irqrestore(&host->lock, flags);
3255 }
3256
3257 /*****************************************************************************\
3258  *                                                                           *
3259  * Interrupt handling                                                        *
3260  *                                                                           *
3261 \*****************************************************************************/
3262
3263 static void sdhci_cmd_irq(struct sdhci_host *host, u32 intmask, u32 *intmask_p)
3264 {
3265         /* Handle auto-CMD12 error */
3266         if (intmask & SDHCI_INT_AUTO_CMD_ERR && host->data_cmd) {
3267                 struct mmc_request *mrq = host->data_cmd->mrq;
3268                 u16 auto_cmd_status = sdhci_readw(host, SDHCI_AUTO_CMD_STATUS);
3269                 int data_err_bit = (auto_cmd_status & SDHCI_AUTO_CMD_TIMEOUT) ?
3270                                    SDHCI_INT_DATA_TIMEOUT :
3271                                    SDHCI_INT_DATA_CRC;
3272
3273                 /* Treat auto-CMD12 error the same as data error */
3274                 if (!mrq->sbc && (host->flags & SDHCI_AUTO_CMD12)) {
3275                         *intmask_p |= data_err_bit;
3276                         return;
3277                 }
3278         }
3279
3280         if (!host->cmd) {
3281                 /*
3282                  * SDHCI recovers from errors by resetting the cmd and data
3283                  * circuits.  Until that is done, there very well might be more
3284                  * interrupts, so ignore them in that case.
3285                  */
3286                 if (host->pending_reset)
3287                         return;
3288                 pr_err("%s: Got command interrupt 0x%08x even though no command operation was in progress.\n",
3289                        mmc_hostname(host->mmc), (unsigned)intmask);
3290                 sdhci_err_stats_inc(host, UNEXPECTED_IRQ);
3291                 sdhci_dumpregs(host);
3292                 return;
3293         }
3294
3295         if (intmask & (SDHCI_INT_TIMEOUT | SDHCI_INT_CRC |
3296                        SDHCI_INT_END_BIT | SDHCI_INT_INDEX)) {
3297                 if (intmask & SDHCI_INT_TIMEOUT) {
3298                         host->cmd->error = -ETIMEDOUT;
3299                         sdhci_err_stats_inc(host, CMD_TIMEOUT);
3300                 } else {
3301                         host->cmd->error = -EILSEQ;
3302                         if (!mmc_op_tuning(host->cmd->opcode))
3303                                 sdhci_err_stats_inc(host, CMD_CRC);
3304                 }
3305                 /* Treat data command CRC error the same as data CRC error */
3306                 if (host->cmd->data &&
3307                     (intmask & (SDHCI_INT_CRC | SDHCI_INT_TIMEOUT)) ==
3308                      SDHCI_INT_CRC) {
3309                         host->cmd = NULL;
3310                         *intmask_p |= SDHCI_INT_DATA_CRC;
3311                         return;
3312                 }
3313
3314                 __sdhci_finish_mrq(host, host->cmd->mrq);
3315                 return;
3316         }
3317
3318         /* Handle auto-CMD23 error */
3319         if (intmask & SDHCI_INT_AUTO_CMD_ERR) {
3320                 struct mmc_request *mrq = host->cmd->mrq;
3321                 u16 auto_cmd_status = sdhci_readw(host, SDHCI_AUTO_CMD_STATUS);
3322                 int err = (auto_cmd_status & SDHCI_AUTO_CMD_TIMEOUT) ?
3323                           -ETIMEDOUT :
3324                           -EILSEQ;
3325
3326                 sdhci_err_stats_inc(host, AUTO_CMD);
3327
3328                 if (sdhci_auto_cmd23(host, mrq)) {
3329                         mrq->sbc->error = err;
3330                         __sdhci_finish_mrq(host, mrq);
3331                         return;
3332                 }
3333         }
3334
3335         if (intmask & SDHCI_INT_RESPONSE)
3336                 sdhci_finish_command(host);
3337 }
3338
3339 static void sdhci_adma_show_error(struct sdhci_host *host)
3340 {
3341         void *desc = host->adma_table;
3342         dma_addr_t dma = host->adma_addr;
3343
3344         sdhci_dumpregs(host);
3345
3346         while (true) {
3347                 struct sdhci_adma2_64_desc *dma_desc = desc;
3348
3349                 if (host->flags & SDHCI_USE_64_BIT_DMA)
3350                         SDHCI_DUMP("%08llx: DMA 0x%08x%08x, LEN 0x%04x, Attr=0x%02x\n",
3351                             (unsigned long long)dma,
3352                             le32_to_cpu(dma_desc->addr_hi),
3353                             le32_to_cpu(dma_desc->addr_lo),
3354                             le16_to_cpu(dma_desc->len),
3355                             le16_to_cpu(dma_desc->cmd));
3356                 else
3357                         SDHCI_DUMP("%08llx: DMA 0x%08x, LEN 0x%04x, Attr=0x%02x\n",
3358                             (unsigned long long)dma,
3359                             le32_to_cpu(dma_desc->addr_lo),
3360                             le16_to_cpu(dma_desc->len),
3361                             le16_to_cpu(dma_desc->cmd));
3362
3363                 desc += host->desc_sz;
3364                 dma += host->desc_sz;
3365
3366                 if (dma_desc->cmd & cpu_to_le16(ADMA2_END))
3367                         break;
3368         }
3369 }
3370
3371 static void sdhci_data_irq(struct sdhci_host *host, u32 intmask)
3372 {
3373         /*
3374          * CMD19 generates _only_ Buffer Read Ready interrupt if
3375          * use sdhci_send_tuning.
3376          * Need to exclude this case: PIO mode and use mmc_send_tuning,
3377          * If not, sdhci_transfer_pio will never be called, make the
3378          * SDHCI_INT_DATA_AVAIL always there, stuck in irq storm.
3379          */
3380         if (intmask & SDHCI_INT_DATA_AVAIL && !host->data) {
3381                 if (mmc_op_tuning(SDHCI_GET_CMD(sdhci_readw(host, SDHCI_COMMAND)))) {
3382                         host->tuning_done = 1;
3383                         wake_up(&host->buf_ready_int);
3384                         return;
3385                 }
3386         }
3387
3388         if (!host->data) {
3389                 struct mmc_command *data_cmd = host->data_cmd;
3390
3391                 /*
3392                  * The "data complete" interrupt is also used to
3393                  * indicate that a busy state has ended. See comment
3394                  * above in sdhci_cmd_irq().
3395                  */
3396                 if (data_cmd && (data_cmd->flags & MMC_RSP_BUSY)) {
3397                         if (intmask & SDHCI_INT_DATA_TIMEOUT) {
3398                                 host->data_cmd = NULL;
3399                                 data_cmd->error = -ETIMEDOUT;
3400                                 sdhci_err_stats_inc(host, CMD_TIMEOUT);
3401                                 __sdhci_finish_mrq(host, data_cmd->mrq);
3402                                 return;
3403                         }
3404                         if (intmask & SDHCI_INT_DATA_END) {
3405                                 host->data_cmd = NULL;
3406                                 /*
3407                                  * Some cards handle busy-end interrupt
3408                                  * before the command completed, so make
3409                                  * sure we do things in the proper order.
3410                                  */
3411                                 if (host->cmd == data_cmd)
3412                                         return;
3413
3414                                 __sdhci_finish_mrq(host, data_cmd->mrq);
3415                                 return;
3416                         }
3417                 }
3418
3419                 /*
3420                  * SDHCI recovers from errors by resetting the cmd and data
3421                  * circuits. Until that is done, there very well might be more
3422                  * interrupts, so ignore them in that case.
3423                  */
3424                 if (host->pending_reset)
3425                         return;
3426
3427                 pr_err("%s: Got data interrupt 0x%08x even though no data operation was in progress.\n",
3428                        mmc_hostname(host->mmc), (unsigned)intmask);
3429                 sdhci_err_stats_inc(host, UNEXPECTED_IRQ);
3430                 sdhci_dumpregs(host);
3431
3432                 return;
3433         }
3434
3435         if (intmask & SDHCI_INT_DATA_TIMEOUT) {
3436                 host->data->error = -ETIMEDOUT;
3437                 sdhci_err_stats_inc(host, DAT_TIMEOUT);
3438         } else if (intmask & SDHCI_INT_DATA_END_BIT) {
3439                 host->data->error = -EILSEQ;
3440                 if (!mmc_op_tuning(SDHCI_GET_CMD(sdhci_readw(host, SDHCI_COMMAND))))
3441                         sdhci_err_stats_inc(host, DAT_CRC);
3442         } else if ((intmask & SDHCI_INT_DATA_CRC) &&
3443                 SDHCI_GET_CMD(sdhci_readw(host, SDHCI_COMMAND))
3444                         != MMC_BUS_TEST_R) {
3445                 host->data->error = -EILSEQ;
3446                 if (!mmc_op_tuning(SDHCI_GET_CMD(sdhci_readw(host, SDHCI_COMMAND))))
3447                         sdhci_err_stats_inc(host, DAT_CRC);
3448         } else if (intmask & SDHCI_INT_ADMA_ERROR) {
3449                 pr_err("%s: ADMA error: 0x%08x\n", mmc_hostname(host->mmc),
3450                        intmask);
3451                 sdhci_adma_show_error(host);
3452                 sdhci_err_stats_inc(host, ADMA);
3453                 host->data->error = -EIO;
3454                 if (host->ops->adma_workaround)
3455                         host->ops->adma_workaround(host, intmask);
3456         }
3457
3458         if (host->data->error)
3459                 sdhci_finish_data(host);
3460         else {
3461                 if (intmask & (SDHCI_INT_DATA_AVAIL | SDHCI_INT_SPACE_AVAIL))
3462                         sdhci_transfer_pio(host);
3463
3464                 /*
3465                  * We currently don't do anything fancy with DMA
3466                  * boundaries, but as we can't disable the feature
3467                  * we need to at least restart the transfer.
3468                  *
3469                  * According to the spec sdhci_readl(host, SDHCI_DMA_ADDRESS)
3470                  * should return a valid address to continue from, but as
3471                  * some controllers are faulty, don't trust them.
3472                  */
3473                 if (intmask & SDHCI_INT_DMA_END) {
3474                         dma_addr_t dmastart, dmanow;
3475
3476                         dmastart = sdhci_sdma_address(host);
3477                         dmanow = dmastart + host->data->bytes_xfered;
3478                         /*
3479                          * Force update to the next DMA block boundary.
3480                          */
3481                         dmanow = (dmanow &
3482                                 ~((dma_addr_t)SDHCI_DEFAULT_BOUNDARY_SIZE - 1)) +
3483                                 SDHCI_DEFAULT_BOUNDARY_SIZE;
3484                         host->data->bytes_xfered = dmanow - dmastart;
3485                         DBG("DMA base %pad, transferred 0x%06x bytes, next %pad\n",
3486                             &dmastart, host->data->bytes_xfered, &dmanow);
3487                         sdhci_set_sdma_addr(host, dmanow);
3488                 }
3489
3490                 if (intmask & SDHCI_INT_DATA_END) {
3491                         if (host->cmd == host->data_cmd) {
3492                                 /*
3493                                  * Data managed to finish before the
3494                                  * command completed. Make sure we do
3495                                  * things in the proper order.
3496                                  */
3497                                 host->data_early = 1;
3498                         } else {
3499                                 sdhci_finish_data(host);
3500                         }
3501                 }
3502         }
3503 }
3504
3505 static inline bool sdhci_defer_done(struct sdhci_host *host,
3506                                     struct mmc_request *mrq)
3507 {
3508         struct mmc_data *data = mrq->data;
3509
3510         return host->pending_reset || host->always_defer_done ||
3511                ((host->flags & SDHCI_REQ_USE_DMA) && data &&
3512                 data->host_cookie == COOKIE_MAPPED);
3513 }
3514
3515 static irqreturn_t sdhci_irq(int irq, void *dev_id)
3516 {
3517         struct mmc_request *mrqs_done[SDHCI_MAX_MRQS] = {0};
3518         irqreturn_t result = IRQ_NONE;
3519         struct sdhci_host *host = dev_id;
3520         u32 intmask, mask, unexpected = 0;
3521         int max_loops = 16;
3522         int i;
3523
3524         spin_lock(&host->lock);
3525
3526         if (host->runtime_suspended) {
3527                 spin_unlock(&host->lock);
3528                 return IRQ_NONE;
3529         }
3530
3531         intmask = sdhci_readl(host, SDHCI_INT_STATUS);
3532         if (!intmask || intmask == 0xffffffff) {
3533                 result = IRQ_NONE;
3534                 goto out;
3535         }
3536
3537         do {
3538                 DBG("IRQ status 0x%08x\n", intmask);
3539
3540                 if (host->ops->irq) {
3541                         intmask = host->ops->irq(host, intmask);
3542                         if (!intmask)
3543                                 goto cont;
3544                 }
3545
3546                 /* Clear selected interrupts. */
3547                 mask = intmask & (SDHCI_INT_CMD_MASK | SDHCI_INT_DATA_MASK |
3548                                   SDHCI_INT_BUS_POWER);
3549                 sdhci_writel(host, mask, SDHCI_INT_STATUS);
3550
3551                 if (intmask & (SDHCI_INT_CARD_INSERT | SDHCI_INT_CARD_REMOVE)) {
3552                         u32 present = sdhci_readl(host, SDHCI_PRESENT_STATE) &
3553                                       SDHCI_CARD_PRESENT;
3554
3555                         /*
3556                          * There is a observation on i.mx esdhc.  INSERT
3557                          * bit will be immediately set again when it gets
3558                          * cleared, if a card is inserted.  We have to mask
3559                          * the irq to prevent interrupt storm which will
3560                          * freeze the system.  And the REMOVE gets the
3561                          * same situation.
3562                          *
3563                          * More testing are needed here to ensure it works
3564                          * for other platforms though.
3565                          */
3566                         host->ier &= ~(SDHCI_INT_CARD_INSERT |
3567                                        SDHCI_INT_CARD_REMOVE);
3568                         host->ier |= present ? SDHCI_INT_CARD_REMOVE :
3569                                                SDHCI_INT_CARD_INSERT;
3570                         sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
3571                         sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
3572
3573                         sdhci_writel(host, intmask & (SDHCI_INT_CARD_INSERT |
3574                                      SDHCI_INT_CARD_REMOVE), SDHCI_INT_STATUS);
3575
3576                         host->thread_isr |= intmask & (SDHCI_INT_CARD_INSERT |
3577                                                        SDHCI_INT_CARD_REMOVE);
3578                         result = IRQ_WAKE_THREAD;
3579                 }
3580
3581                 if (intmask & SDHCI_INT_CMD_MASK)
3582                         sdhci_cmd_irq(host, intmask & SDHCI_INT_CMD_MASK, &intmask);
3583
3584                 if (intmask & SDHCI_INT_DATA_MASK)
3585                         sdhci_data_irq(host, intmask & SDHCI_INT_DATA_MASK);
3586
3587                 if (intmask & SDHCI_INT_BUS_POWER)
3588                         pr_err("%s: Card is consuming too much power!\n",
3589                                 mmc_hostname(host->mmc));
3590
3591                 if (intmask & SDHCI_INT_RETUNE)
3592                         mmc_retune_needed(host->mmc);
3593
3594                 if ((intmask & SDHCI_INT_CARD_INT) &&
3595                     (host->ier & SDHCI_INT_CARD_INT)) {
3596                         sdhci_enable_sdio_irq_nolock(host, false);
3597                         sdio_signal_irq(host->mmc);
3598                 }
3599
3600                 intmask &= ~(SDHCI_INT_CARD_INSERT | SDHCI_INT_CARD_REMOVE |
3601                              SDHCI_INT_CMD_MASK | SDHCI_INT_DATA_MASK |
3602                              SDHCI_INT_ERROR | SDHCI_INT_BUS_POWER |
3603                              SDHCI_INT_RETUNE | SDHCI_INT_CARD_INT);
3604
3605                 if (intmask) {
3606                         unexpected |= intmask;
3607                         sdhci_writel(host, intmask, SDHCI_INT_STATUS);
3608                 }
3609 cont:
3610                 if (result == IRQ_NONE)
3611                         result = IRQ_HANDLED;
3612
3613                 intmask = sdhci_readl(host, SDHCI_INT_STATUS);
3614         } while (intmask && --max_loops);
3615
3616         /* Determine if mrqs can be completed immediately */
3617         for (i = 0; i < SDHCI_MAX_MRQS; i++) {
3618                 struct mmc_request *mrq = host->mrqs_done[i];
3619
3620                 if (!mrq)
3621                         continue;
3622
3623                 if (sdhci_defer_done(host, mrq)) {
3624                         result = IRQ_WAKE_THREAD;
3625                 } else {
3626                         mrqs_done[i] = mrq;
3627                         host->mrqs_done[i] = NULL;
3628                 }
3629         }
3630 out:
3631         if (host->deferred_cmd)
3632                 result = IRQ_WAKE_THREAD;
3633
3634         spin_unlock(&host->lock);
3635
3636         /* Process mrqs ready for immediate completion */
3637         for (i = 0; i < SDHCI_MAX_MRQS; i++) {
3638                 if (!mrqs_done[i])
3639                         continue;
3640
3641                 if (host->ops->request_done)
3642                         host->ops->request_done(host, mrqs_done[i]);
3643                 else
3644                         mmc_request_done(host->mmc, mrqs_done[i]);
3645         }
3646
3647         if (unexpected) {
3648                 pr_err("%s: Unexpected interrupt 0x%08x.\n",
3649                            mmc_hostname(host->mmc), unexpected);
3650                 sdhci_err_stats_inc(host, UNEXPECTED_IRQ);
3651                 sdhci_dumpregs(host);
3652         }
3653
3654         return result;
3655 }
3656
3657 static irqreturn_t sdhci_thread_irq(int irq, void *dev_id)
3658 {
3659         struct sdhci_host *host = dev_id;
3660         struct mmc_command *cmd;
3661         unsigned long flags;
3662         u32 isr;
3663
3664         while (!sdhci_request_done(host))
3665                 ;
3666
3667         spin_lock_irqsave(&host->lock, flags);
3668
3669         isr = host->thread_isr;
3670         host->thread_isr = 0;
3671
3672         cmd = host->deferred_cmd;
3673         if (cmd && !sdhci_send_command_retry(host, cmd, flags))
3674                 sdhci_finish_mrq(host, cmd->mrq);
3675
3676         spin_unlock_irqrestore(&host->lock, flags);
3677
3678         if (isr & (SDHCI_INT_CARD_INSERT | SDHCI_INT_CARD_REMOVE)) {
3679                 struct mmc_host *mmc = host->mmc;
3680
3681                 mmc->ops->card_event(mmc);
3682                 mmc_detect_change(mmc, msecs_to_jiffies(200));
3683         }
3684
3685         return IRQ_HANDLED;
3686 }
3687
3688 /*****************************************************************************\
3689  *                                                                           *
3690  * Suspend/resume                                                            *
3691  *                                                                           *
3692 \*****************************************************************************/
3693
3694 #ifdef CONFIG_PM
3695
3696 static bool sdhci_cd_irq_can_wakeup(struct sdhci_host *host)
3697 {
3698         return mmc_card_is_removable(host->mmc) &&
3699                !(host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION) &&
3700                !mmc_can_gpio_cd(host->mmc);
3701 }
3702
3703 /*
3704  * To enable wakeup events, the corresponding events have to be enabled in
3705  * the Interrupt Status Enable register too. See 'Table 1-6: Wakeup Signal
3706  * Table' in the SD Host Controller Standard Specification.
3707  * It is useless to restore SDHCI_INT_ENABLE state in
3708  * sdhci_disable_irq_wakeups() since it will be set by
3709  * sdhci_enable_card_detection() or sdhci_init().
3710  */
3711 static bool sdhci_enable_irq_wakeups(struct sdhci_host *host)
3712 {
3713         u8 mask = SDHCI_WAKE_ON_INSERT | SDHCI_WAKE_ON_REMOVE |
3714                   SDHCI_WAKE_ON_INT;
3715         u32 irq_val = 0;
3716         u8 wake_val = 0;
3717         u8 val;
3718
3719         if (sdhci_cd_irq_can_wakeup(host)) {
3720                 wake_val |= SDHCI_WAKE_ON_INSERT | SDHCI_WAKE_ON_REMOVE;
3721                 irq_val |= SDHCI_INT_CARD_INSERT | SDHCI_INT_CARD_REMOVE;
3722         }
3723
3724         if (mmc_card_wake_sdio_irq(host->mmc)) {
3725                 wake_val |= SDHCI_WAKE_ON_INT;
3726                 irq_val |= SDHCI_INT_CARD_INT;
3727         }
3728
3729         if (!irq_val)
3730                 return false;
3731
3732         val = sdhci_readb(host, SDHCI_WAKE_UP_CONTROL);
3733         val &= ~mask;
3734         val |= wake_val;
3735         sdhci_writeb(host, val, SDHCI_WAKE_UP_CONTROL);
3736
3737         sdhci_writel(host, irq_val, SDHCI_INT_ENABLE);
3738
3739         host->irq_wake_enabled = !enable_irq_wake(host->irq);
3740
3741         return host->irq_wake_enabled;
3742 }
3743
3744 static void sdhci_disable_irq_wakeups(struct sdhci_host *host)
3745 {
3746         u8 val;
3747         u8 mask = SDHCI_WAKE_ON_INSERT | SDHCI_WAKE_ON_REMOVE
3748                         | SDHCI_WAKE_ON_INT;
3749
3750         val = sdhci_readb(host, SDHCI_WAKE_UP_CONTROL);
3751         val &= ~mask;
3752         sdhci_writeb(host, val, SDHCI_WAKE_UP_CONTROL);
3753
3754         disable_irq_wake(host->irq);
3755
3756         host->irq_wake_enabled = false;
3757 }
3758
3759 int sdhci_suspend_host(struct sdhci_host *host)
3760 {
3761         sdhci_disable_card_detection(host);
3762
3763         mmc_retune_timer_stop(host->mmc);
3764
3765         if (!device_may_wakeup(mmc_dev(host->mmc)) ||
3766             !sdhci_enable_irq_wakeups(host)) {
3767                 host->ier = 0;
3768                 sdhci_writel(host, 0, SDHCI_INT_ENABLE);
3769                 sdhci_writel(host, 0, SDHCI_SIGNAL_ENABLE);
3770                 free_irq(host->irq, host);
3771         }
3772
3773         return 0;
3774 }
3775
3776 EXPORT_SYMBOL_GPL(sdhci_suspend_host);
3777
3778 int sdhci_resume_host(struct sdhci_host *host)
3779 {
3780         struct mmc_host *mmc = host->mmc;
3781         int ret = 0;
3782
3783         if (host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA)) {
3784                 if (host->ops->enable_dma)
3785                         host->ops->enable_dma(host);
3786         }
3787
3788         if ((mmc->pm_flags & MMC_PM_KEEP_POWER) &&
3789             (host->quirks2 & SDHCI_QUIRK2_HOST_OFF_CARD_ON)) {
3790                 /* Card keeps power but host controller does not */
3791                 sdhci_init(host, 0);
3792                 host->pwr = 0;
3793                 host->clock = 0;
3794                 host->reinit_uhs = true;
3795                 mmc->ops->set_ios(mmc, &mmc->ios);
3796         } else {
3797                 sdhci_init(host, (mmc->pm_flags & MMC_PM_KEEP_POWER));
3798         }
3799
3800         if (host->irq_wake_enabled) {
3801                 sdhci_disable_irq_wakeups(host);
3802         } else {
3803                 ret = request_threaded_irq(host->irq, sdhci_irq,
3804                                            sdhci_thread_irq, IRQF_SHARED,
3805                                            mmc_hostname(mmc), host);
3806                 if (ret)
3807                         return ret;
3808         }
3809
3810         sdhci_enable_card_detection(host);
3811
3812         return ret;
3813 }
3814
3815 EXPORT_SYMBOL_GPL(sdhci_resume_host);
3816
3817 int sdhci_runtime_suspend_host(struct sdhci_host *host)
3818 {
3819         unsigned long flags;
3820
3821         mmc_retune_timer_stop(host->mmc);
3822
3823         spin_lock_irqsave(&host->lock, flags);
3824         host->ier &= SDHCI_INT_CARD_INT;
3825         sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
3826         sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
3827         spin_unlock_irqrestore(&host->lock, flags);
3828
3829         synchronize_hardirq(host->irq);
3830
3831         spin_lock_irqsave(&host->lock, flags);
3832         host->runtime_suspended = true;
3833         spin_unlock_irqrestore(&host->lock, flags);
3834
3835         return 0;
3836 }
3837 EXPORT_SYMBOL_GPL(sdhci_runtime_suspend_host);
3838
3839 int sdhci_runtime_resume_host(struct sdhci_host *host, int soft_reset)
3840 {
3841         struct mmc_host *mmc = host->mmc;
3842         unsigned long flags;
3843         int host_flags = host->flags;
3844
3845         if (host_flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA)) {
3846                 if (host->ops->enable_dma)
3847                         host->ops->enable_dma(host);
3848         }
3849
3850         sdhci_init(host, soft_reset);
3851
3852         if (mmc->ios.power_mode != MMC_POWER_UNDEFINED &&
3853             mmc->ios.power_mode != MMC_POWER_OFF) {
3854                 /* Force clock and power re-program */
3855                 host->pwr = 0;
3856                 host->clock = 0;
3857                 host->reinit_uhs = true;
3858                 mmc->ops->start_signal_voltage_switch(mmc, &mmc->ios);
3859                 mmc->ops->set_ios(mmc, &mmc->ios);
3860
3861                 if ((host_flags & SDHCI_PV_ENABLED) &&
3862                     !(host->quirks2 & SDHCI_QUIRK2_PRESET_VALUE_BROKEN)) {
3863                         spin_lock_irqsave(&host->lock, flags);
3864                         sdhci_enable_preset_value(host, true);
3865                         spin_unlock_irqrestore(&host->lock, flags);
3866                 }
3867
3868                 if ((mmc->caps2 & MMC_CAP2_HS400_ES) &&
3869                     mmc->ops->hs400_enhanced_strobe)
3870                         mmc->ops->hs400_enhanced_strobe(mmc, &mmc->ios);
3871         }
3872
3873         spin_lock_irqsave(&host->lock, flags);
3874
3875         host->runtime_suspended = false;
3876
3877         /* Enable SDIO IRQ */
3878         if (sdio_irq_claimed(mmc))
3879                 sdhci_enable_sdio_irq_nolock(host, true);
3880
3881         /* Enable Card Detection */
3882         sdhci_enable_card_detection(host);
3883
3884         spin_unlock_irqrestore(&host->lock, flags);
3885
3886         return 0;
3887 }
3888 EXPORT_SYMBOL_GPL(sdhci_runtime_resume_host);
3889
3890 #endif /* CONFIG_PM */
3891
3892 /*****************************************************************************\
3893  *                                                                           *
3894  * Command Queue Engine (CQE) helpers                                        *
3895  *                                                                           *
3896 \*****************************************************************************/
3897
3898 void sdhci_cqe_enable(struct mmc_host *mmc)
3899 {
3900         struct sdhci_host *host = mmc_priv(mmc);
3901         unsigned long flags;
3902         u8 ctrl;
3903
3904         spin_lock_irqsave(&host->lock, flags);
3905
3906         ctrl = sdhci_readb(host, SDHCI_HOST_CONTROL);
3907         ctrl &= ~SDHCI_CTRL_DMA_MASK;
3908         /*
3909          * Host from V4.10 supports ADMA3 DMA type.
3910          * ADMA3 performs integrated descriptor which is more suitable
3911          * for cmd queuing to fetch both command and transfer descriptors.
3912          */
3913         if (host->v4_mode && (host->caps1 & SDHCI_CAN_DO_ADMA3))
3914                 ctrl |= SDHCI_CTRL_ADMA3;
3915         else if (host->flags & SDHCI_USE_64_BIT_DMA)
3916                 ctrl |= SDHCI_CTRL_ADMA64;
3917         else
3918                 ctrl |= SDHCI_CTRL_ADMA32;
3919         sdhci_writeb(host, ctrl, SDHCI_HOST_CONTROL);
3920
3921         sdhci_writew(host, SDHCI_MAKE_BLKSZ(host->sdma_boundary, 512),
3922                      SDHCI_BLOCK_SIZE);
3923
3924         /* Set maximum timeout */
3925         sdhci_set_timeout(host, NULL);
3926
3927         host->ier = host->cqe_ier;
3928
3929         sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
3930         sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
3931
3932         host->cqe_on = true;
3933
3934         pr_debug("%s: sdhci: CQE on, IRQ mask %#x, IRQ status %#x\n",
3935                  mmc_hostname(mmc), host->ier,
3936                  sdhci_readl(host, SDHCI_INT_STATUS));
3937
3938         spin_unlock_irqrestore(&host->lock, flags);
3939 }
3940 EXPORT_SYMBOL_GPL(sdhci_cqe_enable);
3941
3942 void sdhci_cqe_disable(struct mmc_host *mmc, bool recovery)
3943 {
3944         struct sdhci_host *host = mmc_priv(mmc);
3945         unsigned long flags;
3946
3947         spin_lock_irqsave(&host->lock, flags);
3948
3949         sdhci_set_default_irqs(host);
3950
3951         host->cqe_on = false;
3952
3953         if (recovery)
3954                 sdhci_reset_for(host, CQE_RECOVERY);
3955
3956         pr_debug("%s: sdhci: CQE off, IRQ mask %#x, IRQ status %#x\n",
3957                  mmc_hostname(mmc), host->ier,
3958                  sdhci_readl(host, SDHCI_INT_STATUS));
3959
3960         spin_unlock_irqrestore(&host->lock, flags);
3961 }
3962 EXPORT_SYMBOL_GPL(sdhci_cqe_disable);
3963
3964 bool sdhci_cqe_irq(struct sdhci_host *host, u32 intmask, int *cmd_error,
3965                    int *data_error)
3966 {
3967         u32 mask;
3968
3969         if (!host->cqe_on)
3970                 return false;
3971
3972         if (intmask & (SDHCI_INT_INDEX | SDHCI_INT_END_BIT | SDHCI_INT_CRC)) {
3973                 *cmd_error = -EILSEQ;
3974                 if (!mmc_op_tuning(SDHCI_GET_CMD(sdhci_readw(host, SDHCI_COMMAND))))
3975                         sdhci_err_stats_inc(host, CMD_CRC);
3976         } else if (intmask & SDHCI_INT_TIMEOUT) {
3977                 *cmd_error = -ETIMEDOUT;
3978                 sdhci_err_stats_inc(host, CMD_TIMEOUT);
3979         } else
3980                 *cmd_error = 0;
3981
3982         if (intmask & (SDHCI_INT_DATA_END_BIT | SDHCI_INT_DATA_CRC)) {
3983                 *data_error = -EILSEQ;
3984                 if (!mmc_op_tuning(SDHCI_GET_CMD(sdhci_readw(host, SDHCI_COMMAND))))
3985                         sdhci_err_stats_inc(host, DAT_CRC);
3986         } else if (intmask & SDHCI_INT_DATA_TIMEOUT) {
3987                 *data_error = -ETIMEDOUT;
3988                 sdhci_err_stats_inc(host, DAT_TIMEOUT);
3989         } else if (intmask & SDHCI_INT_ADMA_ERROR) {
3990                 *data_error = -EIO;
3991                 sdhci_err_stats_inc(host, ADMA);
3992         } else
3993                 *data_error = 0;
3994
3995         /* Clear selected interrupts. */
3996         mask = intmask & host->cqe_ier;
3997         sdhci_writel(host, mask, SDHCI_INT_STATUS);
3998
3999         if (intmask & SDHCI_INT_BUS_POWER)
4000                 pr_err("%s: Card is consuming too much power!\n",
4001                        mmc_hostname(host->mmc));
4002
4003         intmask &= ~(host->cqe_ier | SDHCI_INT_ERROR);
4004         if (intmask) {
4005                 sdhci_writel(host, intmask, SDHCI_INT_STATUS);
4006                 pr_err("%s: CQE: Unexpected interrupt 0x%08x.\n",
4007                        mmc_hostname(host->mmc), intmask);
4008                 sdhci_err_stats_inc(host, UNEXPECTED_IRQ);
4009                 sdhci_dumpregs(host);
4010         }
4011
4012         return true;
4013 }
4014 EXPORT_SYMBOL_GPL(sdhci_cqe_irq);
4015
4016 /*****************************************************************************\
4017  *                                                                           *
4018  * Device allocation/registration                                            *
4019  *                                                                           *
4020 \*****************************************************************************/
4021
4022 struct sdhci_host *sdhci_alloc_host(struct device *dev,
4023         size_t priv_size)
4024 {
4025         struct mmc_host *mmc;
4026         struct sdhci_host *host;
4027
4028         WARN_ON(dev == NULL);
4029
4030         mmc = mmc_alloc_host(sizeof(struct sdhci_host) + priv_size, dev);
4031         if (!mmc)
4032                 return ERR_PTR(-ENOMEM);
4033
4034         host = mmc_priv(mmc);
4035         host->mmc = mmc;
4036         host->mmc_host_ops = sdhci_ops;
4037         mmc->ops = &host->mmc_host_ops;
4038
4039         host->flags = SDHCI_SIGNALING_330;
4040
4041         host->cqe_ier     = SDHCI_CQE_INT_MASK;
4042         host->cqe_err_ier = SDHCI_CQE_INT_ERR_MASK;
4043
4044         host->tuning_delay = -1;
4045         host->tuning_loop_count = MAX_TUNING_LOOP;
4046
4047         host->sdma_boundary = SDHCI_DEFAULT_BOUNDARY_ARG;
4048
4049         /*
4050          * The DMA table descriptor count is calculated as the maximum
4051          * number of segments times 2, to allow for an alignment
4052          * descriptor for each segment, plus 1 for a nop end descriptor.
4053          */
4054         host->adma_table_cnt = SDHCI_MAX_SEGS * 2 + 1;
4055         host->max_adma = 65536;
4056
4057         host->max_timeout_count = 0xE;
4058
4059         return host;
4060 }
4061
4062 EXPORT_SYMBOL_GPL(sdhci_alloc_host);
4063
4064 static int sdhci_set_dma_mask(struct sdhci_host *host)
4065 {
4066         struct mmc_host *mmc = host->mmc;
4067         struct device *dev = mmc_dev(mmc);
4068         int ret = -EINVAL;
4069
4070         if (host->quirks2 & SDHCI_QUIRK2_BROKEN_64_BIT_DMA)
4071                 host->flags &= ~SDHCI_USE_64_BIT_DMA;
4072
4073         /* Try 64-bit mask if hardware is capable  of it */
4074         if (host->flags & SDHCI_USE_64_BIT_DMA) {
4075                 ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(64));
4076                 if (ret) {
4077                         pr_warn("%s: Failed to set 64-bit DMA mask.\n",
4078                                 mmc_hostname(mmc));
4079                         host->flags &= ~SDHCI_USE_64_BIT_DMA;
4080                 }
4081         }
4082
4083         /* 32-bit mask as default & fallback */
4084         if (ret) {
4085                 ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(32));
4086                 if (ret)
4087                         pr_warn("%s: Failed to set 32-bit DMA mask.\n",
4088                                 mmc_hostname(mmc));
4089         }
4090
4091         return ret;
4092 }
4093
4094 void __sdhci_read_caps(struct sdhci_host *host, const u16 *ver,
4095                        const u32 *caps, const u32 *caps1)
4096 {
4097         u16 v;
4098         u64 dt_caps_mask = 0;
4099         u64 dt_caps = 0;
4100
4101         if (host->read_caps)
4102                 return;
4103
4104         host->read_caps = true;
4105
4106         if (debug_quirks)
4107                 host->quirks = debug_quirks;
4108
4109         if (debug_quirks2)
4110                 host->quirks2 = debug_quirks2;
4111
4112         sdhci_reset_for_all(host);
4113
4114         if (host->v4_mode)
4115                 sdhci_do_enable_v4_mode(host);
4116
4117         device_property_read_u64(mmc_dev(host->mmc),
4118                                  "sdhci-caps-mask", &dt_caps_mask);
4119         device_property_read_u64(mmc_dev(host->mmc),
4120                                  "sdhci-caps", &dt_caps);
4121
4122         v = ver ? *ver : sdhci_readw(host, SDHCI_HOST_VERSION);
4123         host->version = (v & SDHCI_SPEC_VER_MASK) >> SDHCI_SPEC_VER_SHIFT;
4124
4125         if (caps) {
4126                 host->caps = *caps;
4127         } else {
4128                 host->caps = sdhci_readl(host, SDHCI_CAPABILITIES);
4129                 host->caps &= ~lower_32_bits(dt_caps_mask);
4130                 host->caps |= lower_32_bits(dt_caps);
4131         }
4132
4133         if (host->version < SDHCI_SPEC_300)
4134                 return;
4135
4136         if (caps1) {
4137                 host->caps1 = *caps1;
4138         } else {
4139                 host->caps1 = sdhci_readl(host, SDHCI_CAPABILITIES_1);
4140                 host->caps1 &= ~upper_32_bits(dt_caps_mask);
4141                 host->caps1 |= upper_32_bits(dt_caps);
4142         }
4143 }
4144 EXPORT_SYMBOL_GPL(__sdhci_read_caps);
4145
4146 static void sdhci_allocate_bounce_buffer(struct sdhci_host *host)
4147 {
4148         struct mmc_host *mmc = host->mmc;
4149         unsigned int max_blocks;
4150         unsigned int bounce_size;
4151         int ret;
4152
4153         /*
4154          * Cap the bounce buffer at 64KB. Using a bigger bounce buffer
4155          * has diminishing returns, this is probably because SD/MMC
4156          * cards are usually optimized to handle this size of requests.
4157          */
4158         bounce_size = SZ_64K;
4159         /*
4160          * Adjust downwards to maximum request size if this is less
4161          * than our segment size, else hammer down the maximum
4162          * request size to the maximum buffer size.
4163          */
4164         if (mmc->max_req_size < bounce_size)
4165                 bounce_size = mmc->max_req_size;
4166         max_blocks = bounce_size / 512;
4167
4168         /*
4169          * When we just support one segment, we can get significant
4170          * speedups by the help of a bounce buffer to group scattered
4171          * reads/writes together.
4172          */
4173         host->bounce_buffer = devm_kmalloc(mmc_dev(mmc),
4174                                            bounce_size,
4175                                            GFP_KERNEL);
4176         if (!host->bounce_buffer) {
4177                 pr_err("%s: failed to allocate %u bytes for bounce buffer, falling back to single segments\n",
4178                        mmc_hostname(mmc),
4179                        bounce_size);
4180                 /*
4181                  * Exiting with zero here makes sure we proceed with
4182                  * mmc->max_segs == 1.
4183                  */
4184                 return;
4185         }
4186
4187         host->bounce_addr = dma_map_single(mmc_dev(mmc),
4188                                            host->bounce_buffer,
4189                                            bounce_size,
4190                                            DMA_BIDIRECTIONAL);
4191         ret = dma_mapping_error(mmc_dev(mmc), host->bounce_addr);
4192         if (ret) {
4193                 devm_kfree(mmc_dev(mmc), host->bounce_buffer);
4194                 host->bounce_buffer = NULL;
4195                 /* Again fall back to max_segs == 1 */
4196                 return;
4197         }
4198
4199         host->bounce_buffer_size = bounce_size;
4200
4201         /* Lie about this since we're bouncing */
4202         mmc->max_segs = max_blocks;
4203         mmc->max_seg_size = bounce_size;
4204         mmc->max_req_size = bounce_size;
4205
4206         pr_info("%s bounce up to %u segments into one, max segment size %u bytes\n",
4207                 mmc_hostname(mmc), max_blocks, bounce_size);
4208 }
4209
4210 static inline bool sdhci_can_64bit_dma(struct sdhci_host *host)
4211 {
4212         /*
4213          * According to SD Host Controller spec v4.10, bit[27] added from
4214          * version 4.10 in Capabilities Register is used as 64-bit System
4215          * Address support for V4 mode.
4216          */
4217         if (host->version >= SDHCI_SPEC_410 && host->v4_mode)
4218                 return host->caps & SDHCI_CAN_64BIT_V4;
4219
4220         return host->caps & SDHCI_CAN_64BIT;
4221 }
4222
4223 int sdhci_setup_host(struct sdhci_host *host)
4224 {
4225         struct mmc_host *mmc;
4226         u32 max_current_caps;
4227         unsigned int ocr_avail;
4228         unsigned int override_timeout_clk;
4229         u32 max_clk;
4230         int ret = 0;
4231         bool enable_vqmmc = false;
4232
4233         WARN_ON(host == NULL);
4234         if (host == NULL)
4235                 return -EINVAL;
4236
4237         mmc = host->mmc;
4238
4239         /*
4240          * If there are external regulators, get them. Note this must be done
4241          * early before resetting the host and reading the capabilities so that
4242          * the host can take the appropriate action if regulators are not
4243          * available.
4244          */
4245         if (!mmc->supply.vqmmc) {
4246                 ret = mmc_regulator_get_supply(mmc);
4247                 if (ret)
4248                         return ret;
4249                 enable_vqmmc  = true;
4250         }
4251
4252         DBG("Version:   0x%08x | Present:  0x%08x\n",
4253             sdhci_readw(host, SDHCI_HOST_VERSION),
4254             sdhci_readl(host, SDHCI_PRESENT_STATE));
4255         DBG("Caps:      0x%08x | Caps_1:   0x%08x\n",
4256             sdhci_readl(host, SDHCI_CAPABILITIES),
4257             sdhci_readl(host, SDHCI_CAPABILITIES_1));
4258
4259         sdhci_read_caps(host);
4260
4261         override_timeout_clk = host->timeout_clk;
4262
4263         if (host->version > SDHCI_SPEC_420) {
4264                 pr_err("%s: Unknown controller version (%d). You may experience problems.\n",
4265                        mmc_hostname(mmc), host->version);
4266         }
4267
4268         if (host->quirks & SDHCI_QUIRK_FORCE_DMA)
4269                 host->flags |= SDHCI_USE_SDMA;
4270         else if (!(host->caps & SDHCI_CAN_DO_SDMA))
4271                 DBG("Controller doesn't have SDMA capability\n");
4272         else
4273                 host->flags |= SDHCI_USE_SDMA;
4274
4275         if ((host->quirks & SDHCI_QUIRK_BROKEN_DMA) &&
4276                 (host->flags & SDHCI_USE_SDMA)) {
4277                 DBG("Disabling DMA as it is marked broken\n");
4278                 host->flags &= ~SDHCI_USE_SDMA;
4279         }
4280
4281         if ((host->version >= SDHCI_SPEC_200) &&
4282                 (host->caps & SDHCI_CAN_DO_ADMA2))
4283                 host->flags |= SDHCI_USE_ADMA;
4284
4285         if ((host->quirks & SDHCI_QUIRK_BROKEN_ADMA) &&
4286                 (host->flags & SDHCI_USE_ADMA)) {
4287                 DBG("Disabling ADMA as it is marked broken\n");
4288                 host->flags &= ~SDHCI_USE_ADMA;
4289         }
4290
4291         if (sdhci_can_64bit_dma(host))
4292                 host->flags |= SDHCI_USE_64_BIT_DMA;
4293
4294         if (host->use_external_dma) {
4295                 ret = sdhci_external_dma_init(host);
4296                 if (ret == -EPROBE_DEFER)
4297                         goto unreg;
4298                 /*
4299                  * Fall back to use the DMA/PIO integrated in standard SDHCI
4300                  * instead of external DMA devices.
4301                  */
4302                 else if (ret)
4303                         sdhci_switch_external_dma(host, false);
4304                 /* Disable internal DMA sources */
4305                 else
4306                         host->flags &= ~(SDHCI_USE_SDMA | SDHCI_USE_ADMA);
4307         }
4308
4309         if (host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA)) {
4310                 if (host->ops->set_dma_mask)
4311                         ret = host->ops->set_dma_mask(host);
4312                 else
4313                         ret = sdhci_set_dma_mask(host);
4314
4315                 if (!ret && host->ops->enable_dma)
4316                         ret = host->ops->enable_dma(host);
4317
4318                 if (ret) {
4319                         pr_warn("%s: No suitable DMA available - falling back to PIO\n",
4320                                 mmc_hostname(mmc));
4321                         host->flags &= ~(SDHCI_USE_SDMA | SDHCI_USE_ADMA);
4322
4323                         ret = 0;
4324                 }
4325         }
4326
4327         /* SDMA does not support 64-bit DMA if v4 mode not set */
4328         if ((host->flags & SDHCI_USE_64_BIT_DMA) && !host->v4_mode)
4329                 host->flags &= ~SDHCI_USE_SDMA;
4330
4331         if (host->flags & SDHCI_USE_ADMA) {
4332                 dma_addr_t dma;
4333                 void *buf;
4334
4335                 if (!(host->flags & SDHCI_USE_64_BIT_DMA))
4336                         host->alloc_desc_sz = SDHCI_ADMA2_32_DESC_SZ;
4337                 else if (!host->alloc_desc_sz)
4338                         host->alloc_desc_sz = SDHCI_ADMA2_64_DESC_SZ(host);
4339
4340                 host->desc_sz = host->alloc_desc_sz;
4341                 host->adma_table_sz = host->adma_table_cnt * host->desc_sz;
4342
4343                 host->align_buffer_sz = SDHCI_MAX_SEGS * SDHCI_ADMA2_ALIGN;
4344                 /*
4345                  * Use zalloc to zero the reserved high 32-bits of 128-bit
4346                  * descriptors so that they never need to be written.
4347                  */
4348                 buf = dma_alloc_coherent(mmc_dev(mmc),
4349                                          host->align_buffer_sz + host->adma_table_sz,
4350                                          &dma, GFP_KERNEL);
4351                 if (!buf) {
4352                         pr_warn("%s: Unable to allocate ADMA buffers - falling back to standard DMA\n",
4353                                 mmc_hostname(mmc));
4354                         host->flags &= ~SDHCI_USE_ADMA;
4355                 } else if ((dma + host->align_buffer_sz) &
4356                            (SDHCI_ADMA2_DESC_ALIGN - 1)) {
4357                         pr_warn("%s: unable to allocate aligned ADMA descriptor\n",
4358                                 mmc_hostname(mmc));
4359                         host->flags &= ~SDHCI_USE_ADMA;
4360                         dma_free_coherent(mmc_dev(mmc), host->align_buffer_sz +
4361                                           host->adma_table_sz, buf, dma);
4362                 } else {
4363                         host->align_buffer = buf;
4364                         host->align_addr = dma;
4365
4366                         host->adma_table = buf + host->align_buffer_sz;
4367                         host->adma_addr = dma + host->align_buffer_sz;
4368                 }
4369         }
4370
4371         /*
4372          * If we use DMA, then it's up to the caller to set the DMA
4373          * mask, but PIO does not need the hw shim so we set a new
4374          * mask here in that case.
4375          */
4376         if (!(host->flags & (SDHCI_USE_SDMA | SDHCI_USE_ADMA))) {
4377                 host->dma_mask = DMA_BIT_MASK(64);
4378                 mmc_dev(mmc)->dma_mask = &host->dma_mask;
4379         }
4380
4381         if (host->version >= SDHCI_SPEC_300)
4382                 host->max_clk = FIELD_GET(SDHCI_CLOCK_V3_BASE_MASK, host->caps);
4383         else
4384                 host->max_clk = FIELD_GET(SDHCI_CLOCK_BASE_MASK, host->caps);
4385
4386         host->max_clk *= 1000000;
4387         if (host->max_clk == 0 || host->quirks &
4388                         SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN) {
4389                 if (!host->ops->get_max_clock) {
4390                         pr_err("%s: Hardware doesn't specify base clock frequency.\n",
4391                                mmc_hostname(mmc));
4392                         ret = -ENODEV;
4393                         goto undma;
4394                 }
4395                 host->max_clk = host->ops->get_max_clock(host);
4396         }
4397
4398         /*
4399          * In case of Host Controller v3.00, find out whether clock
4400          * multiplier is supported.
4401          */
4402         host->clk_mul = FIELD_GET(SDHCI_CLOCK_MUL_MASK, host->caps1);
4403
4404         /*
4405          * In case the value in Clock Multiplier is 0, then programmable
4406          * clock mode is not supported, otherwise the actual clock
4407          * multiplier is one more than the value of Clock Multiplier
4408          * in the Capabilities Register.
4409          */
4410         if (host->clk_mul)
4411                 host->clk_mul += 1;
4412
4413         /*
4414          * Set host parameters.
4415          */
4416         max_clk = host->max_clk;
4417
4418         if (host->ops->get_min_clock)
4419                 mmc->f_min = host->ops->get_min_clock(host);
4420         else if (host->version >= SDHCI_SPEC_300) {
4421                 if (host->clk_mul)
4422                         max_clk = host->max_clk * host->clk_mul;
4423                 /*
4424                  * Divided Clock Mode minimum clock rate is always less than
4425                  * Programmable Clock Mode minimum clock rate.
4426                  */
4427                 mmc->f_min = host->max_clk / SDHCI_MAX_DIV_SPEC_300;
4428         } else
4429                 mmc->f_min = host->max_clk / SDHCI_MAX_DIV_SPEC_200;
4430
4431         if (!mmc->f_max || mmc->f_max > max_clk)
4432                 mmc->f_max = max_clk;
4433
4434         if (!(host->quirks & SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK)) {
4435                 host->timeout_clk = FIELD_GET(SDHCI_TIMEOUT_CLK_MASK, host->caps);
4436
4437                 if (host->caps & SDHCI_TIMEOUT_CLK_UNIT)
4438                         host->timeout_clk *= 1000;
4439
4440                 if (host->timeout_clk == 0) {
4441                         if (!host->ops->get_timeout_clock) {
4442                                 pr_err("%s: Hardware doesn't specify timeout clock frequency.\n",
4443                                         mmc_hostname(mmc));
4444                                 ret = -ENODEV;
4445                                 goto undma;
4446                         }
4447
4448                         host->timeout_clk =
4449                                 DIV_ROUND_UP(host->ops->get_timeout_clock(host),
4450                                              1000);
4451                 }
4452
4453                 if (override_timeout_clk)
4454                         host->timeout_clk = override_timeout_clk;
4455
4456                 mmc->max_busy_timeout = host->ops->get_max_timeout_count ?
4457                         host->ops->get_max_timeout_count(host) : 1 << 27;
4458                 mmc->max_busy_timeout /= host->timeout_clk;
4459         }
4460
4461         if (host->quirks2 & SDHCI_QUIRK2_DISABLE_HW_TIMEOUT &&
4462             !host->ops->get_max_timeout_count)
4463                 mmc->max_busy_timeout = 0;
4464
4465         mmc->caps |= MMC_CAP_SDIO_IRQ | MMC_CAP_CMD23;
4466         mmc->caps2 |= MMC_CAP2_SDIO_IRQ_NOTHREAD;
4467
4468         if (host->quirks & SDHCI_QUIRK_MULTIBLOCK_READ_ACMD12)
4469                 host->flags |= SDHCI_AUTO_CMD12;
4470
4471         /*
4472          * For v3 mode, Auto-CMD23 stuff only works in ADMA or PIO.
4473          * For v4 mode, SDMA may use Auto-CMD23 as well.
4474          */
4475         if ((host->version >= SDHCI_SPEC_300) &&
4476             ((host->flags & SDHCI_USE_ADMA) ||
4477              !(host->flags & SDHCI_USE_SDMA) || host->v4_mode) &&
4478              !(host->quirks2 & SDHCI_QUIRK2_ACMD23_BROKEN)) {
4479                 host->flags |= SDHCI_AUTO_CMD23;
4480                 DBG("Auto-CMD23 available\n");
4481         } else {
4482                 DBG("Auto-CMD23 unavailable\n");
4483         }
4484
4485         /*
4486          * A controller may support 8-bit width, but the board itself
4487          * might not have the pins brought out.  Boards that support
4488          * 8-bit width must set "mmc->caps |= MMC_CAP_8_BIT_DATA;" in
4489          * their platform code before calling sdhci_add_host(), and we
4490          * won't assume 8-bit width for hosts without that CAP.
4491          */
4492         if (!(host->quirks & SDHCI_QUIRK_FORCE_1_BIT_DATA))
4493                 mmc->caps |= MMC_CAP_4_BIT_DATA;
4494
4495         if (host->quirks2 & SDHCI_QUIRK2_HOST_NO_CMD23)
4496                 mmc->caps &= ~MMC_CAP_CMD23;
4497
4498         if (host->caps & SDHCI_CAN_DO_HISPD)
4499                 mmc->caps |= MMC_CAP_SD_HIGHSPEED | MMC_CAP_MMC_HIGHSPEED;
4500
4501         if ((host->quirks & SDHCI_QUIRK_BROKEN_CARD_DETECTION) &&
4502             mmc_card_is_removable(mmc) &&
4503             mmc_gpio_get_cd(mmc) < 0)
4504                 mmc->caps |= MMC_CAP_NEEDS_POLL;
4505
4506         if (!IS_ERR(mmc->supply.vqmmc)) {
4507                 if (enable_vqmmc) {
4508                         ret = regulator_enable(mmc->supply.vqmmc);
4509                         host->sdhci_core_to_disable_vqmmc = !ret;
4510                 }
4511
4512                 /* If vqmmc provides no 1.8V signalling, then there's no UHS */
4513                 if (!regulator_is_supported_voltage(mmc->supply.vqmmc, 1700000,
4514                                                     1950000))
4515                         host->caps1 &= ~(SDHCI_SUPPORT_SDR104 |
4516                                          SDHCI_SUPPORT_SDR50 |
4517                                          SDHCI_SUPPORT_DDR50);
4518
4519                 /* In eMMC case vqmmc might be a fixed 1.8V regulator */
4520                 if (!regulator_is_supported_voltage(mmc->supply.vqmmc, 2700000,
4521                                                     3600000))
4522                         host->flags &= ~SDHCI_SIGNALING_330;
4523
4524                 if (ret) {
4525                         pr_warn("%s: Failed to enable vqmmc regulator: %d\n",
4526                                 mmc_hostname(mmc), ret);
4527                         mmc->supply.vqmmc = ERR_PTR(-EINVAL);
4528                 }
4529
4530         }
4531
4532         if (host->quirks2 & SDHCI_QUIRK2_NO_1_8_V) {
4533                 host->caps1 &= ~(SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_SDR50 |
4534                                  SDHCI_SUPPORT_DDR50);
4535                 /*
4536                  * The SDHCI controller in a SoC might support HS200/HS400
4537                  * (indicated using mmc-hs200-1_8v/mmc-hs400-1_8v dt property),
4538                  * but if the board is modeled such that the IO lines are not
4539                  * connected to 1.8v then HS200/HS400 cannot be supported.
4540                  * Disable HS200/HS400 if the board does not have 1.8v connected
4541                  * to the IO lines. (Applicable for other modes in 1.8v)
4542                  */
4543                 mmc->caps2 &= ~(MMC_CAP2_HSX00_1_8V | MMC_CAP2_HS400_ES);
4544                 mmc->caps &= ~(MMC_CAP_1_8V_DDR | MMC_CAP_UHS);
4545         }
4546
4547         /* Any UHS-I mode in caps implies SDR12 and SDR25 support. */
4548         if (host->caps1 & (SDHCI_SUPPORT_SDR104 | SDHCI_SUPPORT_SDR50 |
4549                            SDHCI_SUPPORT_DDR50))
4550                 mmc->caps |= MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25;
4551
4552         /* SDR104 supports also implies SDR50 support */
4553         if (host->caps1 & SDHCI_SUPPORT_SDR104) {
4554                 mmc->caps |= MMC_CAP_UHS_SDR104 | MMC_CAP_UHS_SDR50;
4555                 /* SD3.0: SDR104 is supported so (for eMMC) the caps2
4556                  * field can be promoted to support HS200.
4557                  */
4558                 if (!(host->quirks2 & SDHCI_QUIRK2_BROKEN_HS200))
4559                         mmc->caps2 |= MMC_CAP2_HS200;
4560         } else if (host->caps1 & SDHCI_SUPPORT_SDR50) {
4561                 mmc->caps |= MMC_CAP_UHS_SDR50;
4562         }
4563
4564         if (host->quirks2 & SDHCI_QUIRK2_CAPS_BIT63_FOR_HS400 &&
4565             (host->caps1 & SDHCI_SUPPORT_HS400))
4566                 mmc->caps2 |= MMC_CAP2_HS400;
4567
4568         if ((mmc->caps2 & MMC_CAP2_HSX00_1_2V) &&
4569             (IS_ERR(mmc->supply.vqmmc) ||
4570              !regulator_is_supported_voltage(mmc->supply.vqmmc, 1100000,
4571                                              1300000)))
4572                 mmc->caps2 &= ~MMC_CAP2_HSX00_1_2V;
4573
4574         if ((host->caps1 & SDHCI_SUPPORT_DDR50) &&
4575             !(host->quirks2 & SDHCI_QUIRK2_BROKEN_DDR50))
4576                 mmc->caps |= MMC_CAP_UHS_DDR50;
4577
4578         /* Does the host need tuning for SDR50? */
4579         if (host->caps1 & SDHCI_USE_SDR50_TUNING)
4580                 host->flags |= SDHCI_SDR50_NEEDS_TUNING;
4581
4582         /* Driver Type(s) (A, C, D) supported by the host */
4583         if (host->caps1 & SDHCI_DRIVER_TYPE_A)
4584                 mmc->caps |= MMC_CAP_DRIVER_TYPE_A;
4585         if (host->caps1 & SDHCI_DRIVER_TYPE_C)
4586                 mmc->caps |= MMC_CAP_DRIVER_TYPE_C;
4587         if (host->caps1 & SDHCI_DRIVER_TYPE_D)
4588                 mmc->caps |= MMC_CAP_DRIVER_TYPE_D;
4589
4590         /* Initial value for re-tuning timer count */
4591         host->tuning_count = FIELD_GET(SDHCI_RETUNING_TIMER_COUNT_MASK,
4592                                        host->caps1);
4593
4594         /*
4595          * In case Re-tuning Timer is not disabled, the actual value of
4596          * re-tuning timer will be 2 ^ (n - 1).
4597          */
4598         if (host->tuning_count)
4599                 host->tuning_count = 1 << (host->tuning_count - 1);
4600
4601         /* Re-tuning mode supported by the Host Controller */
4602         host->tuning_mode = FIELD_GET(SDHCI_RETUNING_MODE_MASK, host->caps1);
4603
4604         ocr_avail = 0;
4605
4606         /*
4607          * According to SD Host Controller spec v3.00, if the Host System
4608          * can afford more than 150mA, Host Driver should set XPC to 1. Also
4609          * the value is meaningful only if Voltage Support in the Capabilities
4610          * register is set. The actual current value is 4 times the register
4611          * value.
4612          */
4613         max_current_caps = sdhci_readl(host, SDHCI_MAX_CURRENT);
4614         if (!max_current_caps && !IS_ERR(mmc->supply.vmmc)) {
4615                 int curr = regulator_get_current_limit(mmc->supply.vmmc);
4616                 if (curr > 0) {
4617
4618                         /* convert to SDHCI_MAX_CURRENT format */
4619                         curr = curr/1000;  /* convert to mA */
4620                         curr = curr/SDHCI_MAX_CURRENT_MULTIPLIER;
4621
4622                         curr = min_t(u32, curr, SDHCI_MAX_CURRENT_LIMIT);
4623                         max_current_caps =
4624                                 FIELD_PREP(SDHCI_MAX_CURRENT_330_MASK, curr) |
4625                                 FIELD_PREP(SDHCI_MAX_CURRENT_300_MASK, curr) |
4626                                 FIELD_PREP(SDHCI_MAX_CURRENT_180_MASK, curr);
4627                 }
4628         }
4629
4630         if (host->caps & SDHCI_CAN_VDD_330) {
4631                 ocr_avail |= MMC_VDD_32_33 | MMC_VDD_33_34;
4632
4633                 mmc->max_current_330 = FIELD_GET(SDHCI_MAX_CURRENT_330_MASK,
4634                                                  max_current_caps) *
4635                                                 SDHCI_MAX_CURRENT_MULTIPLIER;
4636         }
4637         if (host->caps & SDHCI_CAN_VDD_300) {
4638                 ocr_avail |= MMC_VDD_29_30 | MMC_VDD_30_31;
4639
4640                 mmc->max_current_300 = FIELD_GET(SDHCI_MAX_CURRENT_300_MASK,
4641                                                  max_current_caps) *
4642                                                 SDHCI_MAX_CURRENT_MULTIPLIER;
4643         }
4644         if (host->caps & SDHCI_CAN_VDD_180) {
4645                 ocr_avail |= MMC_VDD_165_195;
4646
4647                 mmc->max_current_180 = FIELD_GET(SDHCI_MAX_CURRENT_180_MASK,
4648                                                  max_current_caps) *
4649                                                 SDHCI_MAX_CURRENT_MULTIPLIER;
4650         }
4651
4652         /* If OCR set by host, use it instead. */
4653         if (host->ocr_mask)
4654                 ocr_avail = host->ocr_mask;
4655
4656         /* If OCR set by external regulators, give it highest prio. */
4657         if (mmc->ocr_avail)
4658                 ocr_avail = mmc->ocr_avail;
4659
4660         mmc->ocr_avail = ocr_avail;
4661         mmc->ocr_avail_sdio = ocr_avail;
4662         if (host->ocr_avail_sdio)
4663                 mmc->ocr_avail_sdio &= host->ocr_avail_sdio;
4664         mmc->ocr_avail_sd = ocr_avail;
4665         if (host->ocr_avail_sd)
4666                 mmc->ocr_avail_sd &= host->ocr_avail_sd;
4667         else /* normal SD controllers don't support 1.8V */
4668                 mmc->ocr_avail_sd &= ~MMC_VDD_165_195;
4669         mmc->ocr_avail_mmc = ocr_avail;
4670         if (host->ocr_avail_mmc)
4671                 mmc->ocr_avail_mmc &= host->ocr_avail_mmc;
4672
4673         if (mmc->ocr_avail == 0) {
4674                 pr_err("%s: Hardware doesn't report any support voltages.\n",
4675                        mmc_hostname(mmc));
4676                 ret = -ENODEV;
4677                 goto unreg;
4678         }
4679
4680         if ((mmc->caps & (MMC_CAP_UHS_SDR12 | MMC_CAP_UHS_SDR25 |
4681                           MMC_CAP_UHS_SDR50 | MMC_CAP_UHS_SDR104 |
4682                           MMC_CAP_UHS_DDR50 | MMC_CAP_1_8V_DDR)) ||
4683             (mmc->caps2 & (MMC_CAP2_HS200_1_8V_SDR | MMC_CAP2_HS400_1_8V)))
4684                 host->flags |= SDHCI_SIGNALING_180;
4685
4686         if (mmc->caps2 & MMC_CAP2_HSX00_1_2V)
4687                 host->flags |= SDHCI_SIGNALING_120;
4688
4689         spin_lock_init(&host->lock);
4690
4691         /*
4692          * Maximum number of sectors in one transfer. Limited by SDMA boundary
4693          * size (512KiB). Note some tuning modes impose a 4MiB limit, but this
4694          * is less anyway.
4695          */
4696         mmc->max_req_size = 524288;
4697
4698         /*
4699          * Maximum number of segments. Depends on if the hardware
4700          * can do scatter/gather or not.
4701          */
4702         if (host->flags & SDHCI_USE_ADMA) {
4703                 mmc->max_segs = SDHCI_MAX_SEGS;
4704         } else if (host->flags & SDHCI_USE_SDMA) {
4705                 mmc->max_segs = 1;
4706                 mmc->max_req_size = min_t(size_t, mmc->max_req_size,
4707                                           dma_max_mapping_size(mmc_dev(mmc)));
4708         } else { /* PIO */
4709                 mmc->max_segs = SDHCI_MAX_SEGS;
4710         }
4711
4712         /*
4713          * Maximum segment size. Could be one segment with the maximum number
4714          * of bytes. When doing hardware scatter/gather, each entry cannot
4715          * be larger than 64 KiB though.
4716          */
4717         if (host->flags & SDHCI_USE_ADMA) {
4718                 if (host->quirks & SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC) {
4719                         host->max_adma = 65532; /* 32-bit alignment */
4720                         mmc->max_seg_size = 65535;
4721                 } else {
4722                         mmc->max_seg_size = 65536;
4723                 }
4724         } else {
4725                 mmc->max_seg_size = mmc->max_req_size;
4726         }
4727
4728         /*
4729          * Maximum block size. This varies from controller to controller and
4730          * is specified in the capabilities register.
4731          */
4732         if (host->quirks & SDHCI_QUIRK_FORCE_BLK_SZ_2048) {
4733                 mmc->max_blk_size = 2;
4734         } else {
4735                 mmc->max_blk_size = (host->caps & SDHCI_MAX_BLOCK_MASK) >>
4736                                 SDHCI_MAX_BLOCK_SHIFT;
4737                 if (mmc->max_blk_size >= 3) {
4738                         pr_warn("%s: Invalid maximum block size, assuming 512 bytes\n",
4739                                 mmc_hostname(mmc));
4740                         mmc->max_blk_size = 0;
4741                 }
4742         }
4743
4744         mmc->max_blk_size = 512 << mmc->max_blk_size;
4745
4746         /*
4747          * Maximum block count.
4748          */
4749         mmc->max_blk_count = (host->quirks & SDHCI_QUIRK_NO_MULTIBLOCK) ? 1 : 65535;
4750
4751         if (mmc->max_segs == 1)
4752                 /* This may alter mmc->*_blk_* parameters */
4753                 sdhci_allocate_bounce_buffer(host);
4754
4755         return 0;
4756
4757 unreg:
4758         if (host->sdhci_core_to_disable_vqmmc)
4759                 regulator_disable(mmc->supply.vqmmc);
4760 undma:
4761         if (host->align_buffer)
4762                 dma_free_coherent(mmc_dev(mmc), host->align_buffer_sz +
4763                                   host->adma_table_sz, host->align_buffer,
4764                                   host->align_addr);
4765         host->adma_table = NULL;
4766         host->align_buffer = NULL;
4767
4768         return ret;
4769 }
4770 EXPORT_SYMBOL_GPL(sdhci_setup_host);
4771
4772 void sdhci_cleanup_host(struct sdhci_host *host)
4773 {
4774         struct mmc_host *mmc = host->mmc;
4775
4776         if (host->sdhci_core_to_disable_vqmmc)
4777                 regulator_disable(mmc->supply.vqmmc);
4778
4779         if (host->align_buffer)
4780                 dma_free_coherent(mmc_dev(mmc), host->align_buffer_sz +
4781                                   host->adma_table_sz, host->align_buffer,
4782                                   host->align_addr);
4783
4784         if (host->use_external_dma)
4785                 sdhci_external_dma_release(host);
4786
4787         host->adma_table = NULL;
4788         host->align_buffer = NULL;
4789 }
4790 EXPORT_SYMBOL_GPL(sdhci_cleanup_host);
4791
4792 int __sdhci_add_host(struct sdhci_host *host)
4793 {
4794         unsigned int flags = WQ_UNBOUND | WQ_MEM_RECLAIM | WQ_HIGHPRI;
4795         struct mmc_host *mmc = host->mmc;
4796         int ret;
4797
4798         if ((mmc->caps2 & MMC_CAP2_CQE) &&
4799             (host->quirks & SDHCI_QUIRK_BROKEN_CQE)) {
4800                 mmc->caps2 &= ~MMC_CAP2_CQE;
4801                 mmc->cqe_ops = NULL;
4802         }
4803
4804         host->complete_wq = alloc_workqueue("sdhci", flags, 0);
4805         if (!host->complete_wq)
4806                 return -ENOMEM;
4807
4808         INIT_WORK(&host->complete_work, sdhci_complete_work);
4809
4810         timer_setup(&host->timer, sdhci_timeout_timer, 0);
4811         timer_setup(&host->data_timer, sdhci_timeout_data_timer, 0);
4812
4813         init_waitqueue_head(&host->buf_ready_int);
4814
4815         sdhci_init(host, 0);
4816
4817         ret = request_threaded_irq(host->irq, sdhci_irq, sdhci_thread_irq,
4818                                    IRQF_SHARED, mmc_hostname(mmc), host);
4819         if (ret) {
4820                 pr_err("%s: Failed to request IRQ %d: %d\n",
4821                        mmc_hostname(mmc), host->irq, ret);
4822                 goto unwq;
4823         }
4824
4825         ret = sdhci_led_register(host);
4826         if (ret) {
4827                 pr_err("%s: Failed to register LED device: %d\n",
4828                        mmc_hostname(mmc), ret);
4829                 goto unirq;
4830         }
4831
4832         ret = mmc_add_host(mmc);
4833         if (ret)
4834                 goto unled;
4835
4836         pr_info("%s: SDHCI controller on %s [%s] using %s\n",
4837                 mmc_hostname(mmc), host->hw_name, dev_name(mmc_dev(mmc)),
4838                 host->use_external_dma ? "External DMA" :
4839                 (host->flags & SDHCI_USE_ADMA) ?
4840                 (host->flags & SDHCI_USE_64_BIT_DMA) ? "ADMA 64-bit" : "ADMA" :
4841                 (host->flags & SDHCI_USE_SDMA) ? "DMA" : "PIO");
4842
4843         sdhci_enable_card_detection(host);
4844
4845         return 0;
4846
4847 unled:
4848         sdhci_led_unregister(host);
4849 unirq:
4850         sdhci_reset_for_all(host);
4851         sdhci_writel(host, 0, SDHCI_INT_ENABLE);
4852         sdhci_writel(host, 0, SDHCI_SIGNAL_ENABLE);
4853         free_irq(host->irq, host);
4854 unwq:
4855         destroy_workqueue(host->complete_wq);
4856
4857         return ret;
4858 }
4859 EXPORT_SYMBOL_GPL(__sdhci_add_host);
4860
4861 int sdhci_add_host(struct sdhci_host *host)
4862 {
4863         int ret;
4864
4865         ret = sdhci_setup_host(host);
4866         if (ret)
4867                 return ret;
4868
4869         ret = __sdhci_add_host(host);
4870         if (ret)
4871                 goto cleanup;
4872
4873         return 0;
4874
4875 cleanup:
4876         sdhci_cleanup_host(host);
4877
4878         return ret;
4879 }
4880 EXPORT_SYMBOL_GPL(sdhci_add_host);
4881
4882 void sdhci_remove_host(struct sdhci_host *host, int dead)
4883 {
4884         struct mmc_host *mmc = host->mmc;
4885         unsigned long flags;
4886
4887         if (dead) {
4888                 spin_lock_irqsave(&host->lock, flags);
4889
4890                 host->flags |= SDHCI_DEVICE_DEAD;
4891
4892                 if (sdhci_has_requests(host)) {
4893                         pr_err("%s: Controller removed during "
4894                                 " transfer!\n", mmc_hostname(mmc));
4895                         sdhci_error_out_mrqs(host, -ENOMEDIUM);
4896                 }
4897
4898                 spin_unlock_irqrestore(&host->lock, flags);
4899         }
4900
4901         sdhci_disable_card_detection(host);
4902
4903         mmc_remove_host(mmc);
4904
4905         sdhci_led_unregister(host);
4906
4907         if (!dead)
4908                 sdhci_reset_for_all(host);
4909
4910         sdhci_writel(host, 0, SDHCI_INT_ENABLE);
4911         sdhci_writel(host, 0, SDHCI_SIGNAL_ENABLE);
4912         free_irq(host->irq, host);
4913
4914         del_timer_sync(&host->timer);
4915         del_timer_sync(&host->data_timer);
4916
4917         destroy_workqueue(host->complete_wq);
4918
4919         if (host->sdhci_core_to_disable_vqmmc)
4920                 regulator_disable(mmc->supply.vqmmc);
4921
4922         if (host->align_buffer)
4923                 dma_free_coherent(mmc_dev(mmc), host->align_buffer_sz +
4924                                   host->adma_table_sz, host->align_buffer,
4925                                   host->align_addr);
4926
4927         if (host->use_external_dma)
4928                 sdhci_external_dma_release(host);
4929
4930         host->adma_table = NULL;
4931         host->align_buffer = NULL;
4932 }
4933
4934 EXPORT_SYMBOL_GPL(sdhci_remove_host);
4935
4936 void sdhci_free_host(struct sdhci_host *host)
4937 {
4938         mmc_free_host(host->mmc);
4939 }
4940
4941 EXPORT_SYMBOL_GPL(sdhci_free_host);
4942
4943 /*****************************************************************************\
4944  *                                                                           *
4945  * Driver init/exit                                                          *
4946  *                                                                           *
4947 \*****************************************************************************/
4948
4949 static int __init sdhci_drv_init(void)
4950 {
4951         pr_info(DRIVER_NAME
4952                 ": Secure Digital Host Controller Interface driver\n");
4953         pr_info(DRIVER_NAME ": Copyright(c) Pierre Ossman\n");
4954
4955         return 0;
4956 }
4957
4958 static void __exit sdhci_drv_exit(void)
4959 {
4960 }
4961
4962 module_init(sdhci_drv_init);
4963 module_exit(sdhci_drv_exit);
4964
4965 module_param(debug_quirks, uint, 0444);
4966 module_param(debug_quirks2, uint, 0444);
4967
4968 MODULE_AUTHOR("Pierre Ossman <pierre@ossman.eu>");
4969 MODULE_DESCRIPTION("Secure Digital Host Controller Interface core driver");
4970 MODULE_LICENSE("GPL");
4971
4972 MODULE_PARM_DESC(debug_quirks, "Force certain quirks.");
4973 MODULE_PARM_DESC(debug_quirks2, "Force certain other quirks.");