1 // SPDX-License-Identifier: GPL-2.0-or-later
3 * Auvitek AU0828 USB Bridge (Analog video support)
5 * Copyright (C) 2009 Devin Heitmueller <dheitmueller@linuxtv.org>
6 * Copyright (C) 2005-2008 Auvitek International, Ltd.
11 * The hardware scaler supported is unimplemented
12 * AC97 audio support is unimplemented (only i2s audio mode)
19 #include <linux/module.h>
20 #include <linux/slab.h>
21 #include <linux/init.h>
22 #include <linux/device.h>
23 #include <media/v4l2-common.h>
24 #include <media/v4l2-mc.h>
25 #include <media/v4l2-ioctl.h>
26 #include <media/v4l2-event.h>
27 #include <media/tuner.h>
28 #include "au0828-reg.h"
30 static DEFINE_MUTEX(au0828_sysfs_lock);
32 /* ------------------------------------------------------------------
34 ------------------------------------------------------------------*/
36 static unsigned int isoc_debug;
37 module_param(isoc_debug, int, 0644);
38 MODULE_PARM_DESC(isoc_debug, "enable debug messages [isoc transfers]");
40 #define au0828_isocdbg(fmt, arg...) \
43 pr_info("au0828 %s :"fmt, \
48 static inline void i2c_gate_ctrl(struct au0828_dev *dev, int val)
50 if (dev->dvb.frontend && dev->dvb.frontend->ops.analog_ops.i2c_gate_ctrl)
51 dev->dvb.frontend->ops.analog_ops.i2c_gate_ctrl(dev->dvb.frontend, val);
54 static inline void print_err_status(struct au0828_dev *dev,
55 int packet, int status)
57 char *errmsg = "Unknown";
61 errmsg = "unlinked synchronously";
64 errmsg = "unlinked asynchronously";
67 errmsg = "Buffer error (overrun)";
70 errmsg = "Stalled (device not responding)";
73 errmsg = "Babble (bad cable?)";
76 errmsg = "Bit-stuff error (bad cable?)";
79 errmsg = "CRC/Timeout (could be anything)";
82 errmsg = "Device does not respond";
86 au0828_isocdbg("URB status %d [%s].\n", status, errmsg);
88 au0828_isocdbg("URB packet %d, status %d [%s].\n",
89 packet, status, errmsg);
93 static int check_dev(struct au0828_dev *dev)
95 if (test_bit(DEV_DISCONNECTED, &dev->dev_state)) {
96 pr_info("v4l2 ioctl: device not present\n");
100 if (test_bit(DEV_MISCONFIGURED, &dev->dev_state)) {
101 pr_info("v4l2 ioctl: device is misconfigured; close and open it again\n");
108 * IRQ callback, called by URB callback
110 static void au0828_irq_callback(struct urb *urb)
112 struct au0828_dmaqueue *dma_q = urb->context;
113 struct au0828_dev *dev = container_of(dma_q, struct au0828_dev, vidq);
114 unsigned long flags = 0;
117 switch (urb->status) {
118 case 0: /* success */
119 case -ETIMEDOUT: /* NAK */
121 case -ECONNRESET: /* kill */
124 au0828_isocdbg("au0828_irq_callback called: status kill\n");
126 default: /* unknown error */
127 au0828_isocdbg("urb completion error %d.\n", urb->status);
131 /* Copy data from URB */
132 spin_lock_irqsave(&dev->slock, flags);
133 dev->isoc_ctl.isoc_copy(dev, urb);
134 spin_unlock_irqrestore(&dev->slock, flags);
136 /* Reset urb buffers */
137 for (i = 0; i < urb->number_of_packets; i++) {
138 urb->iso_frame_desc[i].status = 0;
139 urb->iso_frame_desc[i].actual_length = 0;
143 urb->status = usb_submit_urb(urb, GFP_ATOMIC);
145 au0828_isocdbg("urb resubmit failed (error=%i)\n",
148 dev->stream_state = STREAM_ON;
152 * Stop and Deallocate URBs
154 static void au0828_uninit_isoc(struct au0828_dev *dev)
159 au0828_isocdbg("au0828: called au0828_uninit_isoc\n");
161 dev->isoc_ctl.nfields = -1;
162 for (i = 0; i < dev->isoc_ctl.num_bufs; i++) {
163 urb = dev->isoc_ctl.urb[i];
165 if (!irqs_disabled())
170 if (dev->isoc_ctl.transfer_buffer[i]) {
171 usb_free_coherent(dev->usbdev,
172 urb->transfer_buffer_length,
173 dev->isoc_ctl.transfer_buffer[i],
177 dev->isoc_ctl.urb[i] = NULL;
179 dev->isoc_ctl.transfer_buffer[i] = NULL;
182 kfree(dev->isoc_ctl.urb);
183 kfree(dev->isoc_ctl.transfer_buffer);
185 dev->isoc_ctl.urb = NULL;
186 dev->isoc_ctl.transfer_buffer = NULL;
187 dev->isoc_ctl.num_bufs = 0;
189 dev->stream_state = STREAM_OFF;
193 * Allocate URBs and start IRQ
195 static int au0828_init_isoc(struct au0828_dev *dev, int max_packets,
196 int num_bufs, int max_pkt_size,
197 int (*isoc_copy) (struct au0828_dev *dev, struct urb *urb))
199 struct au0828_dmaqueue *dma_q = &dev->vidq;
206 au0828_isocdbg("au0828: called au0828_prepare_isoc\n");
208 dev->isoc_ctl.isoc_copy = isoc_copy;
209 dev->isoc_ctl.num_bufs = num_bufs;
211 dev->isoc_ctl.urb = kcalloc(num_bufs, sizeof(void *), GFP_KERNEL);
212 if (!dev->isoc_ctl.urb) {
213 au0828_isocdbg("cannot alloc memory for usb buffers\n");
217 dev->isoc_ctl.transfer_buffer = kcalloc(num_bufs, sizeof(void *),
219 if (!dev->isoc_ctl.transfer_buffer) {
220 au0828_isocdbg("cannot allocate memory for usb transfer\n");
221 kfree(dev->isoc_ctl.urb);
225 dev->isoc_ctl.max_pkt_size = max_pkt_size;
226 dev->isoc_ctl.buf = NULL;
228 sb_size = max_packets * dev->isoc_ctl.max_pkt_size;
230 /* allocate urbs and transfer buffers */
231 for (i = 0; i < dev->isoc_ctl.num_bufs; i++) {
232 urb = usb_alloc_urb(max_packets, GFP_KERNEL);
234 au0828_isocdbg("cannot allocate URB\n");
235 au0828_uninit_isoc(dev);
238 dev->isoc_ctl.urb[i] = urb;
240 dev->isoc_ctl.transfer_buffer[i] = usb_alloc_coherent(dev->usbdev,
241 sb_size, GFP_KERNEL, &urb->transfer_dma);
242 if (!dev->isoc_ctl.transfer_buffer[i]) {
243 au0828_isocdbg("cannot allocate transfer buffer\n");
244 au0828_uninit_isoc(dev);
247 memset(dev->isoc_ctl.transfer_buffer[i], 0, sb_size);
249 pipe = usb_rcvisocpipe(dev->usbdev,
250 dev->isoc_in_endpointaddr);
252 usb_fill_int_urb(urb, dev->usbdev, pipe,
253 dev->isoc_ctl.transfer_buffer[i], sb_size,
254 au0828_irq_callback, dma_q, 1);
256 urb->number_of_packets = max_packets;
257 urb->transfer_flags = URB_ISO_ASAP | URB_NO_TRANSFER_DMA_MAP;
260 for (j = 0; j < max_packets; j++) {
261 urb->iso_frame_desc[j].offset = k;
262 urb->iso_frame_desc[j].length =
263 dev->isoc_ctl.max_pkt_size;
264 k += dev->isoc_ctl.max_pkt_size;
268 /* submit urbs and enables IRQ */
269 for (i = 0; i < dev->isoc_ctl.num_bufs; i++) {
270 rc = usb_submit_urb(dev->isoc_ctl.urb[i], GFP_ATOMIC);
272 au0828_isocdbg("submit of urb %i failed (error=%i)\n",
274 au0828_uninit_isoc(dev);
283 * Announces that a buffer were filled and request the next
285 static inline void buffer_filled(struct au0828_dev *dev,
286 struct au0828_dmaqueue *dma_q,
287 struct au0828_buffer *buf)
289 struct vb2_v4l2_buffer *vb = &buf->vb;
290 struct vb2_queue *q = vb->vb2_buf.vb2_queue;
292 /* Advice that buffer was filled */
293 au0828_isocdbg("[%p/%d] wakeup\n", buf, buf->top_field);
295 if (q->type == V4L2_BUF_TYPE_VIDEO_CAPTURE)
296 vb->sequence = dev->frame_count++;
298 vb->sequence = dev->vbi_frame_count++;
300 vb->field = V4L2_FIELD_INTERLACED;
301 vb->vb2_buf.timestamp = ktime_get_ns();
302 vb2_buffer_done(&vb->vb2_buf, VB2_BUF_STATE_DONE);
306 * Identify the buffer header type and properly handles
308 static void au0828_copy_video(struct au0828_dev *dev,
309 struct au0828_dmaqueue *dma_q,
310 struct au0828_buffer *buf,
312 unsigned char *outp, unsigned long len)
314 void *fieldstart, *startwrite, *startread;
315 int linesdone, currlinedone, offset, lencopy, remain;
316 int bytesperline = dev->width << 1; /* Assumes 16-bit depth @@@@ */
321 if (dma_q->pos + len > buf->length)
322 len = buf->length - dma_q->pos;
327 /* Interlaces frame */
331 fieldstart = outp + bytesperline;
333 linesdone = dma_q->pos / bytesperline;
334 currlinedone = dma_q->pos % bytesperline;
335 offset = linesdone * bytesperline * 2 + currlinedone;
336 startwrite = fieldstart + offset;
337 lencopy = bytesperline - currlinedone;
338 lencopy = lencopy > remain ? remain : lencopy;
340 if ((char *)startwrite + lencopy > (char *)outp + buf->length) {
341 au0828_isocdbg("Overflow of %zi bytes past buffer end (1)\n",
342 ((char *)startwrite + lencopy) -
343 ((char *)outp + buf->length));
344 remain = (char *)outp + buf->length - (char *)startwrite;
349 memcpy(startwrite, startread, lencopy);
354 startwrite += lencopy + bytesperline;
355 startread += lencopy;
356 if (bytesperline > remain)
359 lencopy = bytesperline;
361 if ((char *)startwrite + lencopy > (char *)outp +
363 au0828_isocdbg("Overflow %zi bytes past buf end (2)\n",
364 ((char *)startwrite + lencopy) -
365 ((char *)outp + buf->length));
366 lencopy = remain = (char *)outp + buf->length -
372 memcpy(startwrite, startread, lencopy);
378 /* We have enough data to check for greenscreen */
379 if (outp[0] < 0x60 && outp[1440] < 0x60)
380 dev->greenscreen_detected = 1;
387 * generic routine to get the next available buffer
389 static inline void get_next_buf(struct au0828_dmaqueue *dma_q,
390 struct au0828_buffer **buf)
392 struct au0828_dev *dev = container_of(dma_q, struct au0828_dev, vidq);
394 if (list_empty(&dma_q->active)) {
395 au0828_isocdbg("No active queue to serve\n");
396 dev->isoc_ctl.buf = NULL;
401 /* Get the next buffer */
402 *buf = list_entry(dma_q->active.next, struct au0828_buffer, list);
403 /* Cleans up buffer - Useful for testing for frame/URB loss */
404 list_del(&(*buf)->list);
406 (*buf)->vb_buf = (*buf)->mem;
407 dev->isoc_ctl.buf = *buf;
412 static void au0828_copy_vbi(struct au0828_dev *dev,
413 struct au0828_dmaqueue *dma_q,
414 struct au0828_buffer *buf,
416 unsigned char *outp, unsigned long len)
418 unsigned char *startwrite, *startread;
423 au0828_isocdbg("dev is null\n");
428 au0828_isocdbg("dma_q is null\n");
434 au0828_isocdbg("p is null\n");
438 au0828_isocdbg("outp is null\n");
442 bytesperline = dev->vbi_width;
444 if (dma_q->pos + len > buf->length)
445 len = buf->length - dma_q->pos;
448 startwrite = outp + (dma_q->pos / 2);
450 /* Make sure the bottom field populates the second half of the frame */
451 if (buf->top_field == 0)
452 startwrite += bytesperline * dev->vbi_height;
454 for (i = 0; i < len; i += 2)
455 startwrite[j++] = startread[i+1];
462 * generic routine to get the next available VBI buffer
464 static inline void vbi_get_next_buf(struct au0828_dmaqueue *dma_q,
465 struct au0828_buffer **buf)
467 struct au0828_dev *dev = container_of(dma_q, struct au0828_dev, vbiq);
469 if (list_empty(&dma_q->active)) {
470 au0828_isocdbg("No active queue to serve\n");
471 dev->isoc_ctl.vbi_buf = NULL;
476 /* Get the next buffer */
477 *buf = list_entry(dma_q->active.next, struct au0828_buffer, list);
478 /* Cleans up buffer - Useful for testing for frame/URB loss */
479 list_del(&(*buf)->list);
481 (*buf)->vb_buf = (*buf)->mem;
482 dev->isoc_ctl.vbi_buf = *buf;
487 * Controls the isoc copy of each urb packet
489 static inline int au0828_isoc_copy(struct au0828_dev *dev, struct urb *urb)
491 struct au0828_buffer *buf;
492 struct au0828_buffer *vbi_buf;
493 struct au0828_dmaqueue *dma_q = urb->context;
494 struct au0828_dmaqueue *vbi_dma_q = &dev->vbiq;
495 unsigned char *outp = NULL;
496 unsigned char *vbioutp = NULL;
497 int i, len = 0, rc = 1;
500 unsigned int vbi_field_size;
501 unsigned int remain, lencopy;
506 if (test_bit(DEV_DISCONNECTED, &dev->dev_state) ||
507 test_bit(DEV_MISCONFIGURED, &dev->dev_state))
510 if (urb->status < 0) {
511 print_err_status(dev, -1, urb->status);
512 if (urb->status == -ENOENT)
516 buf = dev->isoc_ctl.buf;
518 outp = vb2_plane_vaddr(&buf->vb.vb2_buf, 0);
520 vbi_buf = dev->isoc_ctl.vbi_buf;
522 vbioutp = vb2_plane_vaddr(&vbi_buf->vb.vb2_buf, 0);
524 for (i = 0; i < urb->number_of_packets; i++) {
525 int status = urb->iso_frame_desc[i].status;
528 print_err_status(dev, i, status);
529 if (urb->iso_frame_desc[i].status != -EPROTO)
533 if (urb->iso_frame_desc[i].actual_length <= 0)
536 if (urb->iso_frame_desc[i].actual_length >
538 au0828_isocdbg("packet bigger than packet size");
542 p = urb->transfer_buffer + urb->iso_frame_desc[i].offset;
544 len = urb->iso_frame_desc[i].actual_length - 4;
550 au0828_isocdbg("Video frame %s\n",
551 (fbyte & 0x40) ? "odd" : "even");
555 buffer_filled(dev, vbi_dma_q, vbi_buf);
556 vbi_get_next_buf(vbi_dma_q, &vbi_buf);
560 vbioutp = vb2_plane_vaddr(
561 &vbi_buf->vb.vb2_buf, 0);
565 buffer_filled(dev, dma_q, buf);
566 get_next_buf(dma_q, &buf);
570 outp = vb2_plane_vaddr(
571 &buf->vb.vb2_buf, 0);
573 /* As long as isoc traffic is arriving, keep
574 resetting the timer */
575 if (dev->vid_timeout_running)
576 mod_timer(&dev->vid_timeout,
577 jiffies + (HZ / 10));
578 if (dev->vbi_timeout_running)
579 mod_timer(&dev->vbi_timeout,
580 jiffies + (HZ / 10));
590 if (vbi_buf != NULL) {
592 vbi_buf->top_field = 1;
594 vbi_buf->top_field = 0;
602 vbi_field_size = dev->vbi_width * dev->vbi_height * 2;
603 if (dev->vbi_read < vbi_field_size) {
604 remain = vbi_field_size - dev->vbi_read;
611 au0828_copy_vbi(dev, vbi_dma_q, vbi_buf, p,
616 dev->vbi_read += lencopy;
619 if (dev->vbi_read >= vbi_field_size && buf != NULL)
620 au0828_copy_video(dev, dma_q, buf, p, outp, len);
625 void au0828_usb_v4l2_media_release(struct au0828_dev *dev)
627 #ifdef CONFIG_MEDIA_CONTROLLER
630 for (i = 0; i < AU0828_MAX_INPUT; i++) {
631 if (AUVI_INPUT(i).type == AU0828_VMUX_UNDEFINED)
633 media_device_unregister_entity(&dev->input_ent[i]);
638 static void au0828_usb_v4l2_release(struct v4l2_device *v4l2_dev)
640 struct au0828_dev *dev =
641 container_of(v4l2_dev, struct au0828_dev, v4l2_dev);
643 v4l2_ctrl_handler_free(&dev->v4l2_ctrl_hdl);
644 v4l2_device_unregister(&dev->v4l2_dev);
645 au0828_usb_v4l2_media_release(dev);
646 au0828_usb_release(dev);
649 int au0828_v4l2_device_register(struct usb_interface *interface,
650 struct au0828_dev *dev)
654 if (AUVI_INPUT(0).type == AU0828_VMUX_UNDEFINED)
657 /* Create the v4l2_device */
658 #ifdef CONFIG_MEDIA_CONTROLLER
659 dev->v4l2_dev.mdev = dev->media_dev;
661 retval = v4l2_device_register(&interface->dev, &dev->v4l2_dev);
663 pr_err("%s() v4l2_device_register failed\n",
668 dev->v4l2_dev.release = au0828_usb_v4l2_release;
670 /* This control handler will inherit the controls from au8522 */
671 retval = v4l2_ctrl_handler_init(&dev->v4l2_ctrl_hdl, 4);
673 pr_err("%s() v4l2_ctrl_handler_init failed\n",
677 dev->v4l2_dev.ctrl_handler = &dev->v4l2_ctrl_hdl;
682 static int queue_setup(struct vb2_queue *vq,
683 unsigned int *nbuffers, unsigned int *nplanes,
684 unsigned int sizes[], struct device *alloc_devs[])
686 struct au0828_dev *dev = vb2_get_drv_priv(vq);
687 unsigned long size = dev->height * dev->bytesperline;
690 return sizes[0] < size ? -EINVAL : 0;
697 buffer_prepare(struct vb2_buffer *vb)
699 struct vb2_v4l2_buffer *vbuf = to_vb2_v4l2_buffer(vb);
700 struct au0828_buffer *buf = container_of(vbuf,
701 struct au0828_buffer, vb);
702 struct au0828_dev *dev = vb2_get_drv_priv(vb->vb2_queue);
704 buf->length = dev->height * dev->bytesperline;
706 if (vb2_plane_size(vb, 0) < buf->length) {
707 pr_err("%s data will not fit into plane (%lu < %lu)\n",
708 __func__, vb2_plane_size(vb, 0), buf->length);
711 vb2_set_plane_payload(&buf->vb.vb2_buf, 0, buf->length);
716 buffer_queue(struct vb2_buffer *vb)
718 struct vb2_v4l2_buffer *vbuf = to_vb2_v4l2_buffer(vb);
719 struct au0828_buffer *buf = container_of(vbuf,
720 struct au0828_buffer,
722 struct au0828_dev *dev = vb2_get_drv_priv(vb->vb2_queue);
723 struct au0828_dmaqueue *vidq = &dev->vidq;
724 unsigned long flags = 0;
726 buf->mem = vb2_plane_vaddr(vb, 0);
727 buf->length = vb2_plane_size(vb, 0);
729 spin_lock_irqsave(&dev->slock, flags);
730 list_add_tail(&buf->list, &vidq->active);
731 spin_unlock_irqrestore(&dev->slock, flags);
734 static int au0828_i2s_init(struct au0828_dev *dev)
736 /* Enable i2s mode */
737 au0828_writereg(dev, AU0828_AUDIOCTRL_50C, 0x01);
742 * Auvitek au0828 analog stream enable
744 static int au0828_analog_stream_enable(struct au0828_dev *d)
746 struct usb_interface *iface;
749 dprintk(1, "au0828_analog_stream_enable called\n");
751 if (test_bit(DEV_DISCONNECTED, &d->dev_state))
754 iface = usb_ifnum_to_if(d->usbdev, 0);
755 if (iface && iface->cur_altsetting->desc.bAlternateSetting != 5) {
756 dprintk(1, "Changing intf#0 to alt 5\n");
757 /* set au0828 interface0 to AS5 here again */
758 ret = usb_set_interface(d->usbdev, 0, 5);
760 pr_info("Au0828 can't set alt setting to 5!\n");
765 h = d->height / 2 + 2;
768 au0828_writereg(d, AU0828_SENSORCTRL_VBI_103, 0x00);
769 au0828_writereg(d, 0x106, 0x00);
771 au0828_writereg(d, 0x110, 0x00);
772 au0828_writereg(d, 0x111, 0x00);
773 au0828_writereg(d, 0x114, w & 0xff);
774 au0828_writereg(d, 0x115, w >> 8);
776 au0828_writereg(d, 0x112, 0x00);
777 au0828_writereg(d, 0x113, 0x00);
778 au0828_writereg(d, 0x116, h & 0xff);
779 au0828_writereg(d, 0x117, h >> 8);
780 au0828_writereg(d, AU0828_SENSORCTRL_100, 0xb3);
785 static int au0828_analog_stream_disable(struct au0828_dev *d)
787 dprintk(1, "au0828_analog_stream_disable called\n");
788 au0828_writereg(d, AU0828_SENSORCTRL_100, 0x0);
792 static void au0828_analog_stream_reset(struct au0828_dev *dev)
794 dprintk(1, "au0828_analog_stream_reset called\n");
795 au0828_writereg(dev, AU0828_SENSORCTRL_100, 0x0);
797 au0828_writereg(dev, AU0828_SENSORCTRL_100, 0xb3);
801 * Some operations needs to stop current streaming
803 static int au0828_stream_interrupt(struct au0828_dev *dev)
805 dev->stream_state = STREAM_INTERRUPT;
806 if (test_bit(DEV_DISCONNECTED, &dev->dev_state))
811 int au0828_start_analog_streaming(struct vb2_queue *vq, unsigned int count)
813 struct au0828_dev *dev = vb2_get_drv_priv(vq);
816 dprintk(1, "au0828_start_analog_streaming called %d\n",
817 dev->streaming_users);
819 if (vq->type == V4L2_BUF_TYPE_VIDEO_CAPTURE)
820 dev->frame_count = 0;
822 dev->vbi_frame_count = 0;
824 if (dev->streaming_users == 0) {
825 /* If we were doing ac97 instead of i2s, it would go here...*/
826 au0828_i2s_init(dev);
827 rc = au0828_init_isoc(dev, AU0828_ISO_PACKETS_PER_URB,
828 AU0828_MAX_ISO_BUFS, dev->max_pkt_size,
831 pr_info("au0828_init_isoc failed\n");
835 v4l2_device_call_all(&dev->v4l2_dev, 0, video, s_stream, 1);
837 if (vq->type == V4L2_BUF_TYPE_VIDEO_CAPTURE) {
838 dev->vid_timeout_running = 1;
839 mod_timer(&dev->vid_timeout, jiffies + (HZ / 10));
840 } else if (vq->type == V4L2_BUF_TYPE_VBI_CAPTURE) {
841 dev->vbi_timeout_running = 1;
842 mod_timer(&dev->vbi_timeout, jiffies + (HZ / 10));
845 dev->streaming_users++;
849 static void au0828_stop_streaming(struct vb2_queue *vq)
851 struct au0828_dev *dev = vb2_get_drv_priv(vq);
852 struct au0828_dmaqueue *vidq = &dev->vidq;
853 unsigned long flags = 0;
855 dprintk(1, "au0828_stop_streaming called %d\n", dev->streaming_users);
857 if (dev->streaming_users-- == 1) {
858 au0828_uninit_isoc(dev);
859 v4l2_device_call_all(&dev->v4l2_dev, 0, video, s_stream, 0);
862 dev->vid_timeout_running = 0;
863 del_timer_sync(&dev->vid_timeout);
865 spin_lock_irqsave(&dev->slock, flags);
866 if (dev->isoc_ctl.buf != NULL) {
867 vb2_buffer_done(&dev->isoc_ctl.buf->vb.vb2_buf,
868 VB2_BUF_STATE_ERROR);
869 dev->isoc_ctl.buf = NULL;
871 while (!list_empty(&vidq->active)) {
872 struct au0828_buffer *buf;
874 buf = list_entry(vidq->active.next, struct au0828_buffer, list);
875 vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_ERROR);
876 list_del(&buf->list);
878 spin_unlock_irqrestore(&dev->slock, flags);
881 void au0828_stop_vbi_streaming(struct vb2_queue *vq)
883 struct au0828_dev *dev = vb2_get_drv_priv(vq);
884 struct au0828_dmaqueue *vbiq = &dev->vbiq;
885 unsigned long flags = 0;
887 dprintk(1, "au0828_stop_vbi_streaming called %d\n",
888 dev->streaming_users);
890 if (dev->streaming_users-- == 1) {
891 au0828_uninit_isoc(dev);
892 v4l2_device_call_all(&dev->v4l2_dev, 0, video, s_stream, 0);
895 spin_lock_irqsave(&dev->slock, flags);
896 if (dev->isoc_ctl.vbi_buf != NULL) {
897 vb2_buffer_done(&dev->isoc_ctl.vbi_buf->vb.vb2_buf,
898 VB2_BUF_STATE_ERROR);
899 dev->isoc_ctl.vbi_buf = NULL;
901 while (!list_empty(&vbiq->active)) {
902 struct au0828_buffer *buf;
904 buf = list_entry(vbiq->active.next, struct au0828_buffer, list);
905 list_del(&buf->list);
906 vb2_buffer_done(&buf->vb.vb2_buf, VB2_BUF_STATE_ERROR);
908 spin_unlock_irqrestore(&dev->slock, flags);
910 dev->vbi_timeout_running = 0;
911 del_timer_sync(&dev->vbi_timeout);
914 static const struct vb2_ops au0828_video_qops = {
915 .queue_setup = queue_setup,
916 .buf_prepare = buffer_prepare,
917 .buf_queue = buffer_queue,
918 .prepare_streaming = v4l_vb2q_enable_media_source,
919 .start_streaming = au0828_start_analog_streaming,
920 .stop_streaming = au0828_stop_streaming,
921 .wait_prepare = vb2_ops_wait_prepare,
922 .wait_finish = vb2_ops_wait_finish,
925 /* ------------------------------------------------------------------
927 ------------------------------------------------------------------*/
929 * au0828_analog_unregister
930 * unregister v4l2 devices
932 int au0828_analog_unregister(struct au0828_dev *dev)
934 dprintk(1, "au0828_analog_unregister called\n");
937 if (AUVI_INPUT(0).type == AU0828_VMUX_UNDEFINED)
940 mutex_lock(&au0828_sysfs_lock);
941 vb2_video_unregister_device(&dev->vdev);
942 vb2_video_unregister_device(&dev->vbi_dev);
943 mutex_unlock(&au0828_sysfs_lock);
945 v4l2_device_disconnect(&dev->v4l2_dev);
946 v4l2_device_put(&dev->v4l2_dev);
951 /* This function ensures that video frames continue to be delivered even if
952 the ITU-656 input isn't receiving any data (thereby preventing applications
953 such as tvtime from hanging) */
954 static void au0828_vid_buffer_timeout(struct timer_list *t)
956 struct au0828_dev *dev = from_timer(dev, t, vid_timeout);
957 struct au0828_dmaqueue *dma_q = &dev->vidq;
958 struct au0828_buffer *buf;
959 unsigned char *vid_data;
960 unsigned long flags = 0;
962 spin_lock_irqsave(&dev->slock, flags);
964 buf = dev->isoc_ctl.buf;
966 vid_data = vb2_plane_vaddr(&buf->vb.vb2_buf, 0);
967 memset(vid_data, 0x00, buf->length); /* Blank green frame */
968 buffer_filled(dev, dma_q, buf);
970 get_next_buf(dma_q, &buf);
972 if (dev->vid_timeout_running == 1)
973 mod_timer(&dev->vid_timeout, jiffies + (HZ / 10));
975 spin_unlock_irqrestore(&dev->slock, flags);
978 static void au0828_vbi_buffer_timeout(struct timer_list *t)
980 struct au0828_dev *dev = from_timer(dev, t, vbi_timeout);
981 struct au0828_dmaqueue *dma_q = &dev->vbiq;
982 struct au0828_buffer *buf;
983 unsigned char *vbi_data;
984 unsigned long flags = 0;
986 spin_lock_irqsave(&dev->slock, flags);
988 buf = dev->isoc_ctl.vbi_buf;
990 vbi_data = vb2_plane_vaddr(&buf->vb.vb2_buf, 0);
991 memset(vbi_data, 0x00, buf->length);
992 buffer_filled(dev, dma_q, buf);
994 vbi_get_next_buf(dma_q, &buf);
996 if (dev->vbi_timeout_running == 1)
997 mod_timer(&dev->vbi_timeout, jiffies + (HZ / 10));
998 spin_unlock_irqrestore(&dev->slock, flags);
1001 static int au0828_v4l2_open(struct file *filp)
1003 struct au0828_dev *dev = video_drvdata(filp);
1007 "%s called std_set %d dev_state %ld stream users %d users %d\n",
1008 __func__, dev->std_set_in_tuner_core, dev->dev_state,
1009 dev->streaming_users, dev->users);
1011 if (mutex_lock_interruptible(&dev->lock))
1012 return -ERESTARTSYS;
1014 ret = v4l2_fh_open(filp);
1016 au0828_isocdbg("%s: v4l2_fh_open() returned error %d\n",
1018 mutex_unlock(&dev->lock);
1022 if (dev->users == 0) {
1023 au0828_analog_stream_enable(dev);
1024 au0828_analog_stream_reset(dev);
1025 dev->stream_state = STREAM_OFF;
1026 set_bit(DEV_INITIALIZED, &dev->dev_state);
1029 mutex_unlock(&dev->lock);
1033 static int au0828_v4l2_close(struct file *filp)
1036 struct au0828_dev *dev = video_drvdata(filp);
1037 struct video_device *vdev = video_devdata(filp);
1040 "%s called std_set %d dev_state %ld stream users %d users %d\n",
1041 __func__, dev->std_set_in_tuner_core, dev->dev_state,
1042 dev->streaming_users, dev->users);
1044 mutex_lock(&dev->lock);
1045 if (vdev->vfl_type == VFL_TYPE_VIDEO && dev->vid_timeout_running) {
1046 /* Cancel timeout thread in case they didn't call streamoff */
1047 dev->vid_timeout_running = 0;
1048 del_timer_sync(&dev->vid_timeout);
1049 } else if (vdev->vfl_type == VFL_TYPE_VBI &&
1050 dev->vbi_timeout_running) {
1051 /* Cancel timeout thread in case they didn't call streamoff */
1052 dev->vbi_timeout_running = 0;
1053 del_timer_sync(&dev->vbi_timeout);
1056 if (test_bit(DEV_DISCONNECTED, &dev->dev_state))
1059 if (dev->users == 1) {
1061 * Avoid putting tuner in sleep if DVB or ALSA are
1064 * On most USB devices like au0828 the tuner can
1065 * be safely put in sleep state here if ALSA isn't
1066 * streaming. Exceptions are some very old USB tuner
1067 * models such as em28xx-based WinTV USB2 which have
1068 * a separate audio output jack. The devices that have
1069 * a separate audio output jack have analog tuners,
1070 * like Philips FM1236. Those devices are always on,
1071 * so the s_power callback are silently ignored.
1072 * So, the current logic here does the following:
1073 * Disable (put tuner to sleep) when
1074 * - ALSA and DVB aren't streaming.
1075 * - the last V4L2 file handler is closed.
1079 * Additionally, this logic could be improved to
1080 * disable the media source if the above conditions
1081 * are met and if the device:
1082 * - doesn't have a separate audio out plug (or
1083 * - doesn't use a silicon tuner like xc2028/3028/4000/5000).
1085 * Once this additional logic is in place, a callback
1086 * is needed to enable the media source and power on
1087 * the tuner, for radio to work.
1089 ret = v4l_enable_media_source(vdev);
1091 v4l2_device_call_all(&dev->v4l2_dev, 0, tuner,
1093 dev->std_set_in_tuner_core = 0;
1095 /* When close the device, set the usb intf0 into alt0 to free
1097 ret = usb_set_interface(dev->usbdev, 0, 0);
1099 pr_info("Au0828 can't set alternate to 0!\n");
1102 _vb2_fop_release(filp, NULL);
1104 mutex_unlock(&dev->lock);
1108 /* Must be called with dev->lock held */
1109 static void au0828_init_tuner(struct au0828_dev *dev)
1111 struct v4l2_frequency f = {
1112 .frequency = dev->ctrl_freq,
1113 .type = V4L2_TUNER_ANALOG_TV,
1116 dprintk(1, "%s called std_set %d dev_state %ld\n", __func__,
1117 dev->std_set_in_tuner_core, dev->dev_state);
1119 if (dev->std_set_in_tuner_core)
1121 dev->std_set_in_tuner_core = 1;
1122 i2c_gate_ctrl(dev, 1);
1123 /* If we've never sent the standard in tuner core, do so now.
1124 We don't do this at device probe because we don't want to
1125 incur the cost of a firmware load */
1126 v4l2_device_call_all(&dev->v4l2_dev, 0, video, s_std, dev->std);
1127 v4l2_device_call_all(&dev->v4l2_dev, 0, tuner, s_frequency, &f);
1128 i2c_gate_ctrl(dev, 0);
1131 static int au0828_set_format(struct au0828_dev *dev, unsigned int cmd,
1132 struct v4l2_format *format)
1135 int width = format->fmt.pix.width;
1136 int height = format->fmt.pix.height;
1138 /* If they are demanding a format other than the one we support,
1139 bail out (tvtime asks for UYVY and then retries with YUYV) */
1140 if (format->fmt.pix.pixelformat != V4L2_PIX_FMT_UYVY)
1143 /* format->fmt.pix.width only support 720 and height 480 */
1149 format->fmt.pix.width = width;
1150 format->fmt.pix.height = height;
1151 format->fmt.pix.pixelformat = V4L2_PIX_FMT_UYVY;
1152 format->fmt.pix.bytesperline = width * 2;
1153 format->fmt.pix.sizeimage = width * height * 2;
1154 format->fmt.pix.colorspace = V4L2_COLORSPACE_SMPTE170M;
1155 format->fmt.pix.field = V4L2_FIELD_INTERLACED;
1157 if (cmd == VIDIOC_TRY_FMT)
1160 /* maybe set new image format, driver current only support 720*480 */
1162 dev->height = height;
1163 dev->frame_size = width * height * 2;
1164 dev->field_size = width * height;
1165 dev->bytesperline = width * 2;
1167 if (dev->stream_state == STREAM_ON) {
1168 dprintk(1, "VIDIOC_SET_FMT: interrupting stream!\n");
1169 ret = au0828_stream_interrupt(dev);
1171 dprintk(1, "error interrupting video stream!\n");
1176 au0828_analog_stream_enable(dev);
1181 static int vidioc_querycap(struct file *file, void *priv,
1182 struct v4l2_capability *cap)
1184 struct au0828_dev *dev = video_drvdata(file);
1186 dprintk(1, "%s called std_set %d dev_state %ld\n", __func__,
1187 dev->std_set_in_tuner_core, dev->dev_state);
1189 strscpy(cap->driver, "au0828", sizeof(cap->driver));
1190 strscpy(cap->card, dev->board.name, sizeof(cap->card));
1191 usb_make_path(dev->usbdev, cap->bus_info, sizeof(cap->bus_info));
1193 /* set the device capabilities */
1195 V4L2_CAP_AUDIO | V4L2_CAP_READWRITE | V4L2_CAP_STREAMING |
1196 V4L2_CAP_TUNER | V4L2_CAP_VBI_CAPTURE | V4L2_CAP_VIDEO_CAPTURE |
1197 V4L2_CAP_DEVICE_CAPS;
1201 static int vidioc_enum_fmt_vid_cap(struct file *file, void *priv,
1202 struct v4l2_fmtdesc *f)
1207 dprintk(1, "%s called\n", __func__);
1209 f->pixelformat = V4L2_PIX_FMT_UYVY;
1214 static int vidioc_g_fmt_vid_cap(struct file *file, void *priv,
1215 struct v4l2_format *f)
1217 struct au0828_dev *dev = video_drvdata(file);
1219 dprintk(1, "%s called std_set %d dev_state %ld\n", __func__,
1220 dev->std_set_in_tuner_core, dev->dev_state);
1222 f->fmt.pix.width = dev->width;
1223 f->fmt.pix.height = dev->height;
1224 f->fmt.pix.pixelformat = V4L2_PIX_FMT_UYVY;
1225 f->fmt.pix.bytesperline = dev->bytesperline;
1226 f->fmt.pix.sizeimage = dev->frame_size;
1227 f->fmt.pix.colorspace = V4L2_COLORSPACE_SMPTE170M; /* NTSC/PAL */
1228 f->fmt.pix.field = V4L2_FIELD_INTERLACED;
1232 static int vidioc_try_fmt_vid_cap(struct file *file, void *priv,
1233 struct v4l2_format *f)
1235 struct au0828_dev *dev = video_drvdata(file);
1237 dprintk(1, "%s called std_set %d dev_state %ld\n", __func__,
1238 dev->std_set_in_tuner_core, dev->dev_state);
1240 return au0828_set_format(dev, VIDIOC_TRY_FMT, f);
1243 static int vidioc_s_fmt_vid_cap(struct file *file, void *priv,
1244 struct v4l2_format *f)
1246 struct au0828_dev *dev = video_drvdata(file);
1249 dprintk(1, "%s called std_set %d dev_state %ld\n", __func__,
1250 dev->std_set_in_tuner_core, dev->dev_state);
1252 rc = check_dev(dev);
1256 if (vb2_is_busy(&dev->vb_vidq)) {
1257 pr_info("%s queue busy\n", __func__);
1262 rc = au0828_set_format(dev, VIDIOC_S_FMT, f);
1267 static int vidioc_s_std(struct file *file, void *priv, v4l2_std_id norm)
1269 struct au0828_dev *dev = video_drvdata(file);
1271 dprintk(1, "%s called std_set %d dev_state %ld\n", __func__,
1272 dev->std_set_in_tuner_core, dev->dev_state);
1274 if (norm == dev->std)
1277 if (dev->streaming_users > 0)
1282 au0828_init_tuner(dev);
1284 i2c_gate_ctrl(dev, 1);
1287 * FIXME: when we support something other than 60Hz standards,
1288 * we are going to have to make the au0828 bridge adjust the size
1289 * of its capture buffer, which is currently hardcoded at 720x480
1292 v4l2_device_call_all(&dev->v4l2_dev, 0, video, s_std, norm);
1294 i2c_gate_ctrl(dev, 0);
1299 static int vidioc_g_std(struct file *file, void *priv, v4l2_std_id *norm)
1301 struct au0828_dev *dev = video_drvdata(file);
1303 dprintk(1, "%s called std_set %d dev_state %ld\n", __func__,
1304 dev->std_set_in_tuner_core, dev->dev_state);
1310 static int vidioc_enum_input(struct file *file, void *priv,
1311 struct v4l2_input *input)
1313 struct au0828_dev *dev = video_drvdata(file);
1316 static const char *inames[] = {
1317 [AU0828_VMUX_UNDEFINED] = "Undefined",
1318 [AU0828_VMUX_COMPOSITE] = "Composite",
1319 [AU0828_VMUX_SVIDEO] = "S-Video",
1320 [AU0828_VMUX_CABLE] = "Cable TV",
1321 [AU0828_VMUX_TELEVISION] = "Television",
1322 [AU0828_VMUX_DVB] = "DVB",
1325 dprintk(1, "%s called std_set %d dev_state %ld\n", __func__,
1326 dev->std_set_in_tuner_core, dev->dev_state);
1330 if (tmp >= AU0828_MAX_INPUT)
1332 if (AUVI_INPUT(tmp).type == 0)
1336 strscpy(input->name, inames[AUVI_INPUT(tmp).type], sizeof(input->name));
1337 if ((AUVI_INPUT(tmp).type == AU0828_VMUX_TELEVISION) ||
1338 (AUVI_INPUT(tmp).type == AU0828_VMUX_CABLE)) {
1339 input->type |= V4L2_INPUT_TYPE_TUNER;
1340 input->audioset = 1;
1342 input->type |= V4L2_INPUT_TYPE_CAMERA;
1343 input->audioset = 2;
1346 input->std = dev->vdev.tvnorms;
1351 static int vidioc_g_input(struct file *file, void *priv, unsigned int *i)
1353 struct au0828_dev *dev = video_drvdata(file);
1355 dprintk(1, "%s called std_set %d dev_state %ld\n", __func__,
1356 dev->std_set_in_tuner_core, dev->dev_state);
1358 *i = dev->ctrl_input;
1362 static void au0828_s_input(struct au0828_dev *dev, int index)
1366 dprintk(1, "%s called std_set %d dev_state %ld\n", __func__,
1367 dev->std_set_in_tuner_core, dev->dev_state);
1369 switch (AUVI_INPUT(index).type) {
1370 case AU0828_VMUX_SVIDEO:
1371 dev->input_type = AU0828_VMUX_SVIDEO;
1372 dev->ctrl_ainput = 1;
1374 case AU0828_VMUX_COMPOSITE:
1375 dev->input_type = AU0828_VMUX_COMPOSITE;
1376 dev->ctrl_ainput = 1;
1378 case AU0828_VMUX_TELEVISION:
1379 dev->input_type = AU0828_VMUX_TELEVISION;
1380 dev->ctrl_ainput = 0;
1383 dprintk(1, "unknown input type set [%d]\n",
1384 AUVI_INPUT(index).type);
1388 dev->ctrl_input = index;
1390 v4l2_device_call_all(&dev->v4l2_dev, 0, video, s_routing,
1391 AUVI_INPUT(index).vmux, 0, 0);
1393 for (i = 0; i < AU0828_MAX_INPUT; i++) {
1395 if (AUVI_INPUT(i).audio_setup == NULL)
1403 (AUVI_INPUT(i).audio_setup)(dev, enable);
1405 /* Make sure we leave it turned on if some
1406 other input is routed to this callback */
1407 if ((AUVI_INPUT(i).audio_setup) !=
1408 ((AUVI_INPUT(index).audio_setup))) {
1409 (AUVI_INPUT(i).audio_setup)(dev, enable);
1414 v4l2_device_call_all(&dev->v4l2_dev, 0, audio, s_routing,
1415 AUVI_INPUT(index).amux, 0, 0);
1418 static int vidioc_s_input(struct file *file, void *priv, unsigned int index)
1420 struct au0828_dev *dev = video_drvdata(file);
1421 struct video_device *vfd = video_devdata(file);
1423 dprintk(1, "VIDIOC_S_INPUT in function %s, input=%d\n", __func__,
1425 if (index >= AU0828_MAX_INPUT)
1427 if (AUVI_INPUT(index).type == 0)
1430 if (dev->ctrl_input == index)
1433 au0828_s_input(dev, index);
1436 * Input has been changed. Disable the media source
1437 * associated with the old input and enable source
1438 * for the newly set input
1440 v4l_disable_media_source(vfd);
1441 return v4l_enable_media_source(vfd);
1444 static int vidioc_enumaudio(struct file *file, void *priv, struct v4l2_audio *a)
1449 dprintk(1, "%s called\n", __func__);
1452 strscpy(a->name, "Television", sizeof(a->name));
1454 strscpy(a->name, "Line in", sizeof(a->name));
1456 a->capability = V4L2_AUDCAP_STEREO;
1460 static int vidioc_g_audio(struct file *file, void *priv, struct v4l2_audio *a)
1462 struct au0828_dev *dev = video_drvdata(file);
1464 dprintk(1, "%s called std_set %d dev_state %ld\n", __func__,
1465 dev->std_set_in_tuner_core, dev->dev_state);
1467 a->index = dev->ctrl_ainput;
1469 strscpy(a->name, "Television", sizeof(a->name));
1471 strscpy(a->name, "Line in", sizeof(a->name));
1473 a->capability = V4L2_AUDCAP_STEREO;
1477 static int vidioc_s_audio(struct file *file, void *priv, const struct v4l2_audio *a)
1479 struct au0828_dev *dev = video_drvdata(file);
1481 if (a->index != dev->ctrl_ainput)
1484 dprintk(1, "%s called std_set %d dev_state %ld\n", __func__,
1485 dev->std_set_in_tuner_core, dev->dev_state);
1489 static int vidioc_g_tuner(struct file *file, void *priv, struct v4l2_tuner *t)
1491 struct au0828_dev *dev = video_drvdata(file);
1492 struct video_device *vfd = video_devdata(file);
1498 ret = v4l_enable_media_source(vfd);
1502 dprintk(1, "%s called std_set %d dev_state %ld\n", __func__,
1503 dev->std_set_in_tuner_core, dev->dev_state);
1505 strscpy(t->name, "Auvitek tuner", sizeof(t->name));
1507 au0828_init_tuner(dev);
1508 i2c_gate_ctrl(dev, 1);
1509 v4l2_device_call_all(&dev->v4l2_dev, 0, tuner, g_tuner, t);
1510 i2c_gate_ctrl(dev, 0);
1514 static int vidioc_s_tuner(struct file *file, void *priv,
1515 const struct v4l2_tuner *t)
1517 struct au0828_dev *dev = video_drvdata(file);
1522 dprintk(1, "%s called std_set %d dev_state %ld\n", __func__,
1523 dev->std_set_in_tuner_core, dev->dev_state);
1525 au0828_init_tuner(dev);
1526 i2c_gate_ctrl(dev, 1);
1527 v4l2_device_call_all(&dev->v4l2_dev, 0, tuner, s_tuner, t);
1528 i2c_gate_ctrl(dev, 0);
1530 dprintk(1, "VIDIOC_S_TUNER: signal = %x, afc = %x\n", t->signal,
1537 static int vidioc_g_frequency(struct file *file, void *priv,
1538 struct v4l2_frequency *freq)
1540 struct au0828_dev *dev = video_drvdata(file);
1542 if (freq->tuner != 0)
1544 dprintk(1, "%s called std_set %d dev_state %ld\n", __func__,
1545 dev->std_set_in_tuner_core, dev->dev_state);
1546 freq->frequency = dev->ctrl_freq;
1550 static int vidioc_s_frequency(struct file *file, void *priv,
1551 const struct v4l2_frequency *freq)
1553 struct au0828_dev *dev = video_drvdata(file);
1554 struct v4l2_frequency new_freq = *freq;
1556 if (freq->tuner != 0)
1559 dprintk(1, "%s called std_set %d dev_state %ld\n", __func__,
1560 dev->std_set_in_tuner_core, dev->dev_state);
1562 au0828_init_tuner(dev);
1563 i2c_gate_ctrl(dev, 1);
1565 v4l2_device_call_all(&dev->v4l2_dev, 0, tuner, s_frequency, freq);
1566 /* Get the actual set (and possibly clamped) frequency */
1567 v4l2_device_call_all(&dev->v4l2_dev, 0, tuner, g_frequency, &new_freq);
1568 dev->ctrl_freq = new_freq.frequency;
1570 i2c_gate_ctrl(dev, 0);
1572 au0828_analog_stream_reset(dev);
1578 /* RAW VBI ioctls */
1580 static int vidioc_g_fmt_vbi_cap(struct file *file, void *priv,
1581 struct v4l2_format *format)
1583 struct au0828_dev *dev = video_drvdata(file);
1585 dprintk(1, "%s called std_set %d dev_state %ld\n", __func__,
1586 dev->std_set_in_tuner_core, dev->dev_state);
1588 format->fmt.vbi.samples_per_line = dev->vbi_width;
1589 format->fmt.vbi.sample_format = V4L2_PIX_FMT_GREY;
1590 format->fmt.vbi.offset = 0;
1591 format->fmt.vbi.flags = 0;
1592 format->fmt.vbi.sampling_rate = 6750000 * 4 / 2;
1594 format->fmt.vbi.count[0] = dev->vbi_height;
1595 format->fmt.vbi.count[1] = dev->vbi_height;
1596 format->fmt.vbi.start[0] = 21;
1597 format->fmt.vbi.start[1] = 284;
1598 memset(format->fmt.vbi.reserved, 0, sizeof(format->fmt.vbi.reserved));
1603 static int vidioc_g_pixelaspect(struct file *file, void *priv,
1604 int type, struct v4l2_fract *f)
1606 struct au0828_dev *dev = video_drvdata(file);
1608 if (type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
1611 dprintk(1, "%s called std_set %d dev_state %ld\n", __func__,
1612 dev->std_set_in_tuner_core, dev->dev_state);
1615 f->denominator = 59;
1620 static int vidioc_g_selection(struct file *file, void *priv,
1621 struct v4l2_selection *s)
1623 struct au0828_dev *dev = video_drvdata(file);
1625 if (s->type != V4L2_BUF_TYPE_VIDEO_CAPTURE)
1628 switch (s->target) {
1629 case V4L2_SEL_TGT_CROP_BOUNDS:
1630 case V4L2_SEL_TGT_CROP_DEFAULT:
1633 s->r.width = dev->width;
1634 s->r.height = dev->height;
1642 #ifdef CONFIG_VIDEO_ADV_DEBUG
1643 static int vidioc_g_register(struct file *file, void *priv,
1644 struct v4l2_dbg_register *reg)
1646 struct au0828_dev *dev = video_drvdata(file);
1648 dprintk(1, "%s called std_set %d dev_state %ld\n", __func__,
1649 dev->std_set_in_tuner_core, dev->dev_state);
1651 reg->val = au0828_read(dev, reg->reg);
1656 static int vidioc_s_register(struct file *file, void *priv,
1657 const struct v4l2_dbg_register *reg)
1659 struct au0828_dev *dev = video_drvdata(file);
1661 dprintk(1, "%s called std_set %d dev_state %ld\n", __func__,
1662 dev->std_set_in_tuner_core, dev->dev_state);
1664 return au0828_writereg(dev, reg->reg, reg->val);
1668 static int vidioc_log_status(struct file *file, void *fh)
1670 struct video_device *vdev = video_devdata(file);
1672 dprintk(1, "%s called\n", __func__);
1674 v4l2_ctrl_log_status(file, fh);
1675 v4l2_device_call_all(vdev->v4l2_dev, 0, core, log_status);
1679 void au0828_v4l2_suspend(struct au0828_dev *dev)
1684 pr_info("stopping V4L2\n");
1686 if (dev->stream_state == STREAM_ON) {
1687 pr_info("stopping V4L2 active URBs\n");
1688 au0828_analog_stream_disable(dev);
1690 for (i = 0; i < dev->isoc_ctl.num_bufs; i++) {
1691 urb = dev->isoc_ctl.urb[i];
1693 if (!irqs_disabled())
1696 usb_unlink_urb(urb);
1701 if (dev->vid_timeout_running)
1702 del_timer_sync(&dev->vid_timeout);
1703 if (dev->vbi_timeout_running)
1704 del_timer_sync(&dev->vbi_timeout);
1707 void au0828_v4l2_resume(struct au0828_dev *dev)
1711 pr_info("restarting V4L2\n");
1713 if (dev->stream_state == STREAM_ON) {
1714 au0828_stream_interrupt(dev);
1715 au0828_init_tuner(dev);
1718 if (dev->vid_timeout_running)
1719 mod_timer(&dev->vid_timeout, jiffies + (HZ / 10));
1720 if (dev->vbi_timeout_running)
1721 mod_timer(&dev->vbi_timeout, jiffies + (HZ / 10));
1723 /* If we were doing ac97 instead of i2s, it would go here...*/
1724 au0828_i2s_init(dev);
1726 au0828_analog_stream_enable(dev);
1728 if (!(dev->stream_state == STREAM_ON)) {
1729 au0828_analog_stream_reset(dev);
1731 for (i = 0; i < dev->isoc_ctl.num_bufs; i++) {
1732 rc = usb_submit_urb(dev->isoc_ctl.urb[i], GFP_ATOMIC);
1734 au0828_isocdbg("submit of urb %i failed (error=%i)\n",
1736 au0828_uninit_isoc(dev);
1742 static const struct v4l2_file_operations au0828_v4l_fops = {
1743 .owner = THIS_MODULE,
1744 .open = au0828_v4l2_open,
1745 .release = au0828_v4l2_close,
1746 .read = vb2_fop_read,
1747 .poll = vb2_fop_poll,
1748 .mmap = vb2_fop_mmap,
1749 .unlocked_ioctl = video_ioctl2,
1752 static const struct v4l2_ioctl_ops video_ioctl_ops = {
1753 .vidioc_querycap = vidioc_querycap,
1754 .vidioc_enum_fmt_vid_cap = vidioc_enum_fmt_vid_cap,
1755 .vidioc_g_fmt_vid_cap = vidioc_g_fmt_vid_cap,
1756 .vidioc_try_fmt_vid_cap = vidioc_try_fmt_vid_cap,
1757 .vidioc_s_fmt_vid_cap = vidioc_s_fmt_vid_cap,
1758 .vidioc_g_fmt_vbi_cap = vidioc_g_fmt_vbi_cap,
1759 .vidioc_try_fmt_vbi_cap = vidioc_g_fmt_vbi_cap,
1760 .vidioc_s_fmt_vbi_cap = vidioc_g_fmt_vbi_cap,
1761 .vidioc_enumaudio = vidioc_enumaudio,
1762 .vidioc_g_audio = vidioc_g_audio,
1763 .vidioc_s_audio = vidioc_s_audio,
1764 .vidioc_g_pixelaspect = vidioc_g_pixelaspect,
1765 .vidioc_g_selection = vidioc_g_selection,
1767 .vidioc_reqbufs = vb2_ioctl_reqbufs,
1768 .vidioc_create_bufs = vb2_ioctl_create_bufs,
1769 .vidioc_prepare_buf = vb2_ioctl_prepare_buf,
1770 .vidioc_querybuf = vb2_ioctl_querybuf,
1771 .vidioc_qbuf = vb2_ioctl_qbuf,
1772 .vidioc_dqbuf = vb2_ioctl_dqbuf,
1773 .vidioc_expbuf = vb2_ioctl_expbuf,
1775 .vidioc_s_std = vidioc_s_std,
1776 .vidioc_g_std = vidioc_g_std,
1777 .vidioc_enum_input = vidioc_enum_input,
1778 .vidioc_g_input = vidioc_g_input,
1779 .vidioc_s_input = vidioc_s_input,
1781 .vidioc_streamon = vb2_ioctl_streamon,
1782 .vidioc_streamoff = vb2_ioctl_streamoff,
1784 .vidioc_g_tuner = vidioc_g_tuner,
1785 .vidioc_s_tuner = vidioc_s_tuner,
1786 .vidioc_g_frequency = vidioc_g_frequency,
1787 .vidioc_s_frequency = vidioc_s_frequency,
1788 #ifdef CONFIG_VIDEO_ADV_DEBUG
1789 .vidioc_g_register = vidioc_g_register,
1790 .vidioc_s_register = vidioc_s_register,
1792 .vidioc_log_status = vidioc_log_status,
1793 .vidioc_subscribe_event = v4l2_ctrl_subscribe_event,
1794 .vidioc_unsubscribe_event = v4l2_event_unsubscribe,
1797 static const struct video_device au0828_video_template = {
1798 .fops = &au0828_v4l_fops,
1799 .release = video_device_release_empty,
1800 .ioctl_ops = &video_ioctl_ops,
1801 .tvnorms = V4L2_STD_NTSC_M | V4L2_STD_PAL_M,
1804 static int au0828_vb2_setup(struct au0828_dev *dev)
1807 struct vb2_queue *q;
1809 /* Setup Videobuf2 for Video capture */
1811 q->type = V4L2_BUF_TYPE_VIDEO_CAPTURE;
1812 q->io_modes = VB2_READ | VB2_MMAP | VB2_USERPTR | VB2_DMABUF;
1813 q->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC;
1815 q->buf_struct_size = sizeof(struct au0828_buffer);
1816 q->ops = &au0828_video_qops;
1817 q->mem_ops = &vb2_vmalloc_memops;
1819 rc = vb2_queue_init(q);
1823 /* Setup Videobuf2 for VBI capture */
1825 q->type = V4L2_BUF_TYPE_VBI_CAPTURE;
1826 q->io_modes = VB2_READ | VB2_MMAP | VB2_USERPTR | VB2_DMABUF;
1827 q->timestamp_flags = V4L2_BUF_FLAG_TIMESTAMP_MONOTONIC;
1829 q->buf_struct_size = sizeof(struct au0828_buffer);
1830 q->ops = &au0828_vbi_qops;
1831 q->mem_ops = &vb2_vmalloc_memops;
1833 rc = vb2_queue_init(q);
1840 static void au0828_analog_create_entities(struct au0828_dev *dev)
1842 #if defined(CONFIG_MEDIA_CONTROLLER)
1843 static const char * const inames[] = {
1844 [AU0828_VMUX_COMPOSITE] = "Composite",
1845 [AU0828_VMUX_SVIDEO] = "S-Video",
1846 [AU0828_VMUX_CABLE] = "Cable TV",
1847 [AU0828_VMUX_TELEVISION] = "Television",
1848 [AU0828_VMUX_DVB] = "DVB",
1852 /* Initialize Video and VBI pads */
1853 dev->video_pad.flags = MEDIA_PAD_FL_SINK;
1854 ret = media_entity_pads_init(&dev->vdev.entity, 1, &dev->video_pad);
1856 pr_err("failed to initialize video media entity!\n");
1858 dev->vbi_pad.flags = MEDIA_PAD_FL_SINK;
1859 ret = media_entity_pads_init(&dev->vbi_dev.entity, 1, &dev->vbi_pad);
1861 pr_err("failed to initialize vbi media entity!\n");
1863 /* Create entities for each input connector */
1864 for (i = 0; i < AU0828_MAX_INPUT; i++) {
1865 struct media_entity *ent = &dev->input_ent[i];
1867 if (AUVI_INPUT(i).type == AU0828_VMUX_UNDEFINED)
1870 ent->name = inames[AUVI_INPUT(i).type];
1871 ent->flags = MEDIA_ENT_FL_CONNECTOR;
1872 dev->input_pad[i].flags = MEDIA_PAD_FL_SOURCE;
1874 switch (AUVI_INPUT(i).type) {
1875 case AU0828_VMUX_COMPOSITE:
1876 ent->function = MEDIA_ENT_F_CONN_COMPOSITE;
1878 case AU0828_VMUX_SVIDEO:
1879 ent->function = MEDIA_ENT_F_CONN_SVIDEO;
1881 case AU0828_VMUX_CABLE:
1882 case AU0828_VMUX_TELEVISION:
1883 case AU0828_VMUX_DVB:
1884 default: /* Just to shut up a warning */
1885 ent->function = MEDIA_ENT_F_CONN_RF;
1889 ret = media_entity_pads_init(ent, 1, &dev->input_pad[i]);
1891 pr_err("failed to initialize input pad[%d]!\n", i);
1893 ret = media_device_register_entity(dev->media_dev, ent);
1895 pr_err("failed to register input entity %d!\n", i);
1900 /**************************************************************************/
1902 int au0828_analog_register(struct au0828_dev *dev,
1903 struct usb_interface *interface)
1905 int retval = -ENOMEM;
1906 struct usb_host_interface *iface_desc;
1907 struct usb_endpoint_descriptor *endpoint;
1910 dprintk(1, "au0828_analog_register called for intf#%d!\n",
1911 interface->cur_altsetting->desc.bInterfaceNumber);
1914 if (AUVI_INPUT(0).type == AU0828_VMUX_UNDEFINED)
1917 /* set au0828 usb interface0 to as5 */
1918 retval = usb_set_interface(dev->usbdev,
1919 interface->cur_altsetting->desc.bInterfaceNumber, 5);
1921 pr_info("Failure setting usb interface0 to as5\n");
1925 /* Figure out which endpoint has the isoc interface */
1926 iface_desc = interface->cur_altsetting;
1927 for (i = 0; i < iface_desc->desc.bNumEndpoints; i++) {
1928 endpoint = &iface_desc->endpoint[i].desc;
1929 if (((endpoint->bEndpointAddress & USB_ENDPOINT_DIR_MASK)
1931 ((endpoint->bmAttributes & USB_ENDPOINT_XFERTYPE_MASK)
1932 == USB_ENDPOINT_XFER_ISOC)) {
1934 /* we find our isoc in endpoint */
1935 u16 tmp = le16_to_cpu(endpoint->wMaxPacketSize);
1936 dev->max_pkt_size = (tmp & 0x07ff) *
1937 (((tmp & 0x1800) >> 11) + 1);
1938 dev->isoc_in_endpointaddr = endpoint->bEndpointAddress;
1940 "Found isoc endpoint 0x%02x, max size = %d\n",
1941 dev->isoc_in_endpointaddr, dev->max_pkt_size);
1944 if (!(dev->isoc_in_endpointaddr)) {
1945 pr_info("Could not locate isoc endpoint\n");
1949 init_waitqueue_head(&dev->open);
1950 spin_lock_init(&dev->slock);
1952 /* init video dma queues */
1953 INIT_LIST_HEAD(&dev->vidq.active);
1954 INIT_LIST_HEAD(&dev->vbiq.active);
1956 timer_setup(&dev->vid_timeout, au0828_vid_buffer_timeout, 0);
1957 timer_setup(&dev->vbi_timeout, au0828_vbi_buffer_timeout, 0);
1959 dev->width = NTSC_STD_W;
1960 dev->height = NTSC_STD_H;
1961 dev->field_size = dev->width * dev->height;
1962 dev->frame_size = dev->field_size << 1;
1963 dev->bytesperline = dev->width << 1;
1964 dev->vbi_width = 720;
1965 dev->vbi_height = 1;
1966 dev->ctrl_ainput = 0;
1967 dev->ctrl_freq = 960;
1968 dev->std = V4L2_STD_NTSC_M;
1969 /* Default input is TV Tuner */
1970 au0828_s_input(dev, 0);
1972 mutex_init(&dev->vb_queue_lock);
1973 mutex_init(&dev->vb_vbi_queue_lock);
1975 /* Fill the video capture device struct */
1976 dev->vdev = au0828_video_template;
1977 dev->vdev.v4l2_dev = &dev->v4l2_dev;
1978 dev->vdev.lock = &dev->lock;
1979 dev->vdev.queue = &dev->vb_vidq;
1980 dev->vdev.queue->lock = &dev->vb_queue_lock;
1981 dev->vdev.device_caps =
1982 V4L2_CAP_AUDIO | V4L2_CAP_READWRITE | V4L2_CAP_STREAMING |
1983 V4L2_CAP_TUNER | V4L2_CAP_VIDEO_CAPTURE;
1984 strscpy(dev->vdev.name, "au0828a video", sizeof(dev->vdev.name));
1986 /* Setup the VBI device */
1987 dev->vbi_dev = au0828_video_template;
1988 dev->vbi_dev.v4l2_dev = &dev->v4l2_dev;
1989 dev->vbi_dev.lock = &dev->lock;
1990 dev->vbi_dev.queue = &dev->vb_vbiq;
1991 dev->vbi_dev.queue->lock = &dev->vb_vbi_queue_lock;
1992 dev->vbi_dev.device_caps =
1993 V4L2_CAP_AUDIO | V4L2_CAP_READWRITE | V4L2_CAP_STREAMING |
1994 V4L2_CAP_TUNER | V4L2_CAP_VBI_CAPTURE;
1995 strscpy(dev->vbi_dev.name, "au0828a vbi", sizeof(dev->vbi_dev.name));
1997 /* Init entities at the Media Controller */
1998 au0828_analog_create_entities(dev);
2000 /* initialize videobuf2 stuff */
2001 retval = au0828_vb2_setup(dev);
2003 dprintk(1, "unable to setup videobuf2 queues (error = %d).\n",
2008 /* Register the v4l2 device */
2009 video_set_drvdata(&dev->vdev, dev);
2010 retval = video_register_device(&dev->vdev, VFL_TYPE_VIDEO, -1);
2012 dprintk(1, "unable to register video device (error = %d).\n",
2017 /* Register the vbi device */
2018 video_set_drvdata(&dev->vbi_dev, dev);
2019 retval = video_register_device(&dev->vbi_dev, VFL_TYPE_VBI, -1);
2021 dprintk(1, "unable to register vbi device (error = %d).\n",
2024 goto err_reg_vbi_dev;
2027 #ifdef CONFIG_MEDIA_CONTROLLER
2028 retval = v4l2_mc_create_media_graph(dev->media_dev);
2030 pr_err("%s() au0282_dev_register failed to create graph\n",
2033 goto err_reg_vbi_dev;
2037 dprintk(1, "%s completed!\n", __func__);
2042 vb2_video_unregister_device(&dev->vdev);