1 // SPDX-License-Identifier: GPL-2.0-or-later
3 * Copyright (C) 2005-2009 Texas Instruments Inc
5 * CCDC hardware module for DM355
6 * ------------------------------
8 * This module is for configuring DM355 CCD controller of VPFE to capture
9 * Raw yuv or Bayer RGB data from a decoder. CCDC has several modules
10 * such as Defect Pixel Correction, Color Space Conversion etc to
11 * pre-process the Bayer RGB data, before writing it to SDRAM.
13 * TODO: 1) Raw bayer parameter settings and bayer capture
14 * 2) Split module parameter structure to module specific ioctl structs
15 * 3) add support for lense shading correction
16 * 4) investigate if enum used for user space type definition
17 * to be replaced by #defines or integer
19 #include <linux/platform_device.h>
20 #include <linux/uaccess.h>
21 #include <linux/videodev2.h>
22 #include <linux/err.h>
23 #include <linux/module.h>
25 #include <media/davinci/dm355_ccdc.h>
26 #include <media/davinci/vpss.h>
28 #include "dm355_ccdc_regs.h"
29 #include "ccdc_hw_device.h"
31 MODULE_LICENSE("GPL");
32 MODULE_DESCRIPTION("CCDC Driver for DM355");
33 MODULE_AUTHOR("Texas Instruments");
35 static struct ccdc_oper_config {
37 /* CCDC interface type */
38 enum vpfe_hw_if_type if_type;
39 /* Raw Bayer configuration */
40 struct ccdc_params_raw bayer;
41 /* YCbCr configuration */
42 struct ccdc_params_ycbcr ycbcr;
43 /* ccdc base address */
44 void __iomem *base_addr;
46 /* Raw configurations */
48 .pix_fmt = CCDC_PIXFMT_RAW,
49 .frm_fmt = CCDC_FRMFMT_PROGRESSIVE,
51 .fid_pol = VPFE_PINPOL_POSITIVE,
52 .vd_pol = VPFE_PINPOL_POSITIVE,
53 .hd_pol = VPFE_PINPOL_POSITIVE,
62 .mfilt1 = CCDC_NO_MEDIAN_FILTER1,
63 .mfilt2 = CCDC_NO_MEDIAN_FILTER2,
72 .olop = CCDC_GREEN_BLUE,
75 .elep = CCDC_GREEN_RED
78 .olop = CCDC_GREEN_BLUE,
81 .elep = CCDC_GREEN_RED
85 /* YCbCr configuration */
88 .pix_fmt = CCDC_PIXFMT_YCBCR_8BIT,
89 .frm_fmt = CCDC_FRMFMT_INTERLACED,
90 .fid_pol = VPFE_PINPOL_POSITIVE,
91 .vd_pol = VPFE_PINPOL_POSITIVE,
92 .hd_pol = VPFE_PINPOL_POSITIVE,
94 .pix_order = CCDC_PIXORDER_CBYCRY,
95 .buf_type = CCDC_BUFTYPE_FLD_INTERLEAVED
100 /* Raw Bayer formats */
101 static u32 ccdc_raw_bayer_pix_formats[] =
102 {V4L2_PIX_FMT_SBGGR8, V4L2_PIX_FMT_SBGGR16};
104 /* Raw YUV formats */
105 static u32 ccdc_raw_yuv_pix_formats[] =
106 {V4L2_PIX_FMT_UYVY, V4L2_PIX_FMT_YUYV};
108 /* register access routines */
109 static inline u32 regr(u32 offset)
111 return __raw_readl(ccdc_cfg.base_addr + offset);
114 static inline void regw(u32 val, u32 offset)
116 __raw_writel(val, ccdc_cfg.base_addr + offset);
119 static void ccdc_enable(int en)
123 temp &= (~CCDC_SYNCEN_VDHDEN_MASK);
124 temp |= (en & CCDC_SYNCEN_VDHDEN_MASK);
128 static void ccdc_enable_output_to_sdram(int en)
132 temp &= (~(CCDC_SYNCEN_WEN_MASK));
133 temp |= ((en << CCDC_SYNCEN_WEN_SHIFT) & CCDC_SYNCEN_WEN_MASK);
137 static void ccdc_config_gain_offset(void)
140 regw(ccdc_cfg.bayer.gain.r_ye, RYEGAIN);
141 regw(ccdc_cfg.bayer.gain.gr_cy, GRCYGAIN);
142 regw(ccdc_cfg.bayer.gain.gb_g, GBGGAIN);
143 regw(ccdc_cfg.bayer.gain.b_mg, BMGGAIN);
144 /* configure offset */
145 regw(ccdc_cfg.bayer.ccdc_offset, OFFSET);
149 * ccdc_restore_defaults()
150 * This function restore power on defaults in the ccdc registers
152 static int ccdc_restore_defaults(void)
156 dev_dbg(ccdc_cfg.dev, "\nstarting ccdc_restore_defaults...");
157 /* set all registers to zero */
158 for (i = 0; i <= CCDC_REG_LAST; i += 4)
161 /* now override the values with power on defaults in registers */
162 regw(MODESET_DEFAULT, MODESET);
163 /* no culling support */
164 regw(CULH_DEFAULT, CULH);
165 regw(CULV_DEFAULT, CULV);
166 /* Set default Gain and Offset */
167 ccdc_cfg.bayer.gain.r_ye = GAIN_DEFAULT;
168 ccdc_cfg.bayer.gain.gb_g = GAIN_DEFAULT;
169 ccdc_cfg.bayer.gain.gr_cy = GAIN_DEFAULT;
170 ccdc_cfg.bayer.gain.b_mg = GAIN_DEFAULT;
171 ccdc_config_gain_offset();
172 regw(OUTCLIP_DEFAULT, OUTCLIP);
173 regw(LSCCFG2_DEFAULT, LSCCFG2);
174 /* select ccdc input */
175 if (vpss_select_ccdc_source(VPSS_CCDCIN)) {
176 dev_dbg(ccdc_cfg.dev, "\ncouldn't select ccdc input source");
179 /* select ccdc clock */
180 if (vpss_enable_clock(VPSS_CCDC_CLOCK, 1) < 0) {
181 dev_dbg(ccdc_cfg.dev, "\ncouldn't enable ccdc clock");
184 dev_dbg(ccdc_cfg.dev, "\nEnd of ccdc_restore_defaults...");
188 static int ccdc_open(struct device *device)
190 return ccdc_restore_defaults();
193 static int ccdc_close(struct device *device)
196 vpss_enable_clock(VPSS_CCDC_CLOCK, 0);
197 /* do nothing for now */
202 * This function will configure the window size to
203 * be capture in CCDC reg.
205 static void ccdc_setwin(struct v4l2_rect *image_win,
206 enum ccdc_frmfmt frm_fmt, int ppc)
208 int horz_start, horz_nr_pixels;
209 int vert_start, vert_nr_lines;
212 dev_dbg(ccdc_cfg.dev, "\nStarting ccdc_setwin...");
215 * ppc - per pixel count. indicates how many pixels per cell
216 * output to SDRAM. example, for ycbcr, it is one y and one c, so 2.
217 * raw capture this is 1
219 horz_start = image_win->left << (ppc - 1);
220 horz_nr_pixels = ((image_win->width) << (ppc - 1)) - 1;
222 /* Writing the horizontal info into the registers */
223 regw(horz_start, SPH);
224 regw(horz_nr_pixels, NPH);
225 vert_start = image_win->top;
227 if (frm_fmt == CCDC_FRMFMT_INTERLACED) {
228 vert_nr_lines = (image_win->height >> 1) - 1;
230 /* Since first line doesn't have any data */
232 /* configure VDINT0 and VDINT1 */
233 regw(vert_start, VDINT0);
235 /* Since first line doesn't have any data */
237 vert_nr_lines = image_win->height - 1;
238 /* configure VDINT0 and VDINT1 */
239 mid_img = vert_start + (image_win->height / 2);
240 regw(vert_start, VDINT0);
241 regw(mid_img, VDINT1);
243 regw(vert_start & CCDC_START_VER_ONE_MASK, SLV0);
244 regw(vert_start & CCDC_START_VER_TWO_MASK, SLV1);
245 regw(vert_nr_lines & CCDC_NUM_LINES_VER, NLV);
246 dev_dbg(ccdc_cfg.dev, "\nEnd of ccdc_setwin...");
249 /* This function will configure CCDC for YCbCr video capture */
250 static void ccdc_config_ycbcr(void)
252 struct ccdc_params_ycbcr *params = &ccdc_cfg.ycbcr;
255 /* first set the CCDC power on defaults values in all registers */
256 dev_dbg(ccdc_cfg.dev, "\nStarting ccdc_config_ycbcr...");
257 ccdc_restore_defaults();
259 /* configure pixel format & video frame format */
260 temp = (((params->pix_fmt & CCDC_INPUT_MODE_MASK) <<
261 CCDC_INPUT_MODE_SHIFT) |
262 ((params->frm_fmt & CCDC_FRM_FMT_MASK) <<
263 CCDC_FRM_FMT_SHIFT));
265 /* setup BT.656 sync mode */
266 if (params->bt656_enable) {
267 regw(CCDC_REC656IF_BT656_EN, REC656IF);
269 * configure the FID, VD, HD pin polarity fld,hd pol positive,
270 * vd negative, 8-bit pack mode
272 temp |= CCDC_VD_POL_NEGATIVE;
273 } else { /* y/c external sync mode */
274 temp |= (((params->fid_pol & CCDC_FID_POL_MASK) <<
275 CCDC_FID_POL_SHIFT) |
276 ((params->hd_pol & CCDC_HD_POL_MASK) <<
278 ((params->vd_pol & CCDC_VD_POL_MASK) <<
282 /* pack the data to 8-bit */
283 temp |= CCDC_DATA_PACK_ENABLE;
287 /* configure video window */
288 ccdc_setwin(¶ms->win, params->frm_fmt, 2);
290 /* configure the order of y cb cr in SD-RAM */
291 temp = (params->pix_order << CCDC_Y8POS_SHIFT);
292 temp |= CCDC_LATCH_ON_VSYNC_DISABLE | CCDC_CCDCFG_FIDMD_NO_LATCH_VSYNC;
296 * configure the horizontal line offset. This is done by rounding up
297 * width to a multiple of 16 pixels and multiply by two to account for
300 regw(((params->win.width * 2 + 31) >> 5), HSIZE);
302 /* configure the memory line offset */
303 if (params->buf_type == CCDC_BUFTYPE_FLD_INTERLEAVED) {
304 /* two fields are interleaved in memory */
305 regw(CCDC_SDOFST_FIELD_INTERLEAVED, SDOFST);
308 dev_dbg(ccdc_cfg.dev, "\nEnd of ccdc_config_ycbcr...\n");
312 * ccdc_config_black_clamp()
313 * configure parameters for Optical Black Clamp
315 static void ccdc_config_black_clamp(struct ccdc_black_clamp *bclamp)
319 if (!bclamp->b_clamp_enable) {
320 /* configure DCSub */
321 regw(bclamp->dc_sub & CCDC_BLK_DC_SUB_MASK, DCSUB);
325 /* Enable the Black clamping, set sample lines and pixels */
326 val = (bclamp->start_pixel & CCDC_BLK_ST_PXL_MASK) |
327 ((bclamp->sample_pixel & CCDC_BLK_SAMPLE_LN_MASK) <<
328 CCDC_BLK_SAMPLE_LN_SHIFT) | CCDC_BLK_CLAMP_ENABLE;
331 /* If Black clamping is enable then make dcsub 0 */
332 val = (bclamp->sample_ln & CCDC_NUM_LINE_CALC_MASK)
333 << CCDC_NUM_LINE_CALC_SHIFT;
338 * ccdc_config_black_compense()
339 * configure parameters for Black Compensation
341 static void ccdc_config_black_compense(struct ccdc_black_compensation *bcomp)
345 val = (bcomp->b & CCDC_BLK_COMP_MASK) |
346 ((bcomp->gb & CCDC_BLK_COMP_MASK) <<
347 CCDC_BLK_COMP_GB_COMP_SHIFT);
350 val = ((bcomp->gr & CCDC_BLK_COMP_MASK) <<
351 CCDC_BLK_COMP_GR_COMP_SHIFT) |
352 ((bcomp->r & CCDC_BLK_COMP_MASK) <<
353 CCDC_BLK_COMP_R_COMP_SHIFT);
358 * ccdc_write_dfc_entry()
359 * write an entry in the dfc table.
361 static int ccdc_write_dfc_entry(int index, struct ccdc_vertical_dft *dfc)
363 /* TODO This is to be re-visited and adjusted */
364 #define DFC_WRITE_WAIT_COUNT 1000
365 u32 val, count = DFC_WRITE_WAIT_COUNT;
367 regw(dfc->dft_corr_vert[index], DFCMEM0);
368 regw(dfc->dft_corr_horz[index], DFCMEM1);
369 regw(dfc->dft_corr_sub1[index], DFCMEM2);
370 regw(dfc->dft_corr_sub2[index], DFCMEM3);
371 regw(dfc->dft_corr_sub3[index], DFCMEM4);
372 /* set WR bit to write */
373 val = regr(DFCMEMCTL) | CCDC_DFCMEMCTL_DFCMWR_MASK;
374 regw(val, DFCMEMCTL);
377 * Assume, it is very short. If we get an error, we need to
380 while (regr(DFCMEMCTL) & CCDC_DFCMEMCTL_DFCMWR_MASK)
383 * TODO We expect the count to be non-zero to be successful. Adjust
384 * the count if write requires more time
388 dev_err(ccdc_cfg.dev, "defect table write timeout !!!\n");
396 * configure parameters for Vertical Defect Correction
398 static int ccdc_config_vdfc(struct ccdc_vertical_dft *dfc)
403 /* Configure General Defect Correction. The table used is from IPIPE */
404 val = dfc->gen_dft_en & CCDC_DFCCTL_GDFCEN_MASK;
406 /* Configure Vertical Defect Correction if needed */
407 if (!dfc->ver_dft_en) {
408 /* Enable only General Defect Correction */
413 if (dfc->table_size > CCDC_DFT_TABLE_SIZE)
416 val |= CCDC_DFCCTL_VDFC_DISABLE;
417 val |= (dfc->dft_corr_ctl.vdfcsl & CCDC_DFCCTL_VDFCSL_MASK) <<
418 CCDC_DFCCTL_VDFCSL_SHIFT;
419 val |= (dfc->dft_corr_ctl.vdfcuda & CCDC_DFCCTL_VDFCUDA_MASK) <<
420 CCDC_DFCCTL_VDFCUDA_SHIFT;
421 val |= (dfc->dft_corr_ctl.vdflsft & CCDC_DFCCTL_VDFLSFT_MASK) <<
422 CCDC_DFCCTL_VDFLSFT_SHIFT;
425 /* clear address ptr to offset 0 */
426 val = CCDC_DFCMEMCTL_DFCMARST_MASK << CCDC_DFCMEMCTL_DFCMARST_SHIFT;
428 /* write defect table entries */
429 for (i = 0; i < dfc->table_size; i++) {
430 /* increment address for non zero index */
432 val = CCDC_DFCMEMCTL_INC_ADDR;
433 regw(val, DFCMEMCTL);
434 if (ccdc_write_dfc_entry(i, dfc) < 0)
438 /* update saturation level and enable dfc */
439 regw(dfc->saturation_ctl & CCDC_VDC_DFCVSAT_MASK, DFCVSAT);
440 val = regr(DFCCTL) | (CCDC_DFCCTL_VDFCEN_MASK <<
441 CCDC_DFCCTL_VDFCEN_SHIFT);
448 * configure parameters for color space conversion
449 * Each register CSCM0-7 has two values in S8Q5 format.
451 static void ccdc_config_csc(struct ccdc_csc *csc)
459 /* Enable the CSC sub-module */
460 regw(CCDC_CSC_ENABLE, CSCCTL);
462 /* Converting the co-eff as per the format of the register */
463 for (i = 0; i < CCDC_CSC_COEFF_TABLE_SIZE; i++) {
466 val1 = (csc->coeff[i].integer &
467 CCDC_CSC_COEF_INTEG_MASK)
468 << CCDC_CSC_COEF_INTEG_SHIFT;
470 * convert decimal part to binary. Use 2 decimal
471 * precision, user values range from .00 - 0.99
473 val1 |= (((csc->coeff[i].decimal &
474 CCDC_CSC_COEF_DECIMAL_MASK) *
475 CCDC_CSC_DEC_MAX) / 100);
479 val2 = (csc->coeff[i].integer &
480 CCDC_CSC_COEF_INTEG_MASK)
481 << CCDC_CSC_COEF_INTEG_SHIFT;
482 val2 |= (((csc->coeff[i].decimal &
483 CCDC_CSC_COEF_DECIMAL_MASK) *
484 CCDC_CSC_DEC_MAX) / 100);
485 val2 <<= CCDC_CSCM_MSB_SHIFT;
487 regw(val2, (CSCM0 + ((i - 1) << 1)));
493 * ccdc_config_color_patterns()
494 * configure parameters for color patterns
496 static void ccdc_config_color_patterns(struct ccdc_col_pat *pat0,
497 struct ccdc_col_pat *pat1)
501 val = (pat0->olop | (pat0->olep << 2) | (pat0->elop << 4) |
502 (pat0->elep << 6) | (pat1->olop << 8) | (pat1->olep << 10) |
503 (pat1->elop << 12) | (pat1->elep << 14));
507 /* This function will configure CCDC for Raw mode image capture */
508 static int ccdc_config_raw(void)
510 struct ccdc_params_raw *params = &ccdc_cfg.bayer;
511 struct ccdc_config_params_raw *config_params =
512 &ccdc_cfg.bayer.config_params;
515 dev_dbg(ccdc_cfg.dev, "\nStarting ccdc_config_raw...");
517 /* restore power on defaults to register */
518 ccdc_restore_defaults();
521 * set CCD Not to swap input since input is RAW data
522 * set FID detection function to Latch at V-Sync
523 * set WENLOG - ccdc valid area to AND
524 * set TRGSEL to WENBIT
525 * set EXTRG to DISABLE
526 * disable latching function on VSYNC - shadowed registers
528 regw(CCDC_YCINSWP_RAW | CCDC_CCDCFG_FIDMD_LATCH_VSYNC |
529 CCDC_CCDCFG_WENLOG_AND | CCDC_CCDCFG_TRGSEL_WEN |
530 CCDC_CCDCFG_EXTRG_DISABLE | CCDC_LATCH_ON_VSYNC_DISABLE, CCDCFG);
533 * Set VDHD direction to input, input type to raw input
534 * normal data polarity, do not use external WEN
536 val = (CCDC_VDHDOUT_INPUT | CCDC_RAW_IP_MODE | CCDC_DATAPOL_NORMAL |
540 * Configure the vertical sync polarity (MODESET.VDPOL), horizontal
541 * sync polarity (MODESET.HDPOL), field id polarity (MODESET.FLDPOL),
542 * frame format(progressive or interlace), & pixel format (Input mode)
544 val |= (((params->vd_pol & CCDC_VD_POL_MASK) << CCDC_VD_POL_SHIFT) |
545 ((params->hd_pol & CCDC_HD_POL_MASK) << CCDC_HD_POL_SHIFT) |
546 ((params->fid_pol & CCDC_FID_POL_MASK) << CCDC_FID_POL_SHIFT) |
547 ((params->frm_fmt & CCDC_FRM_FMT_MASK) << CCDC_FRM_FMT_SHIFT) |
548 ((params->pix_fmt & CCDC_PIX_FMT_MASK) << CCDC_PIX_FMT_SHIFT));
550 /* set pack for alaw compression */
551 if ((config_params->data_sz == CCDC_DATA_8BITS) ||
552 config_params->alaw.enable)
553 val |= CCDC_DATA_PACK_ENABLE;
555 /* Configure for LPF */
556 if (config_params->lpf_enable)
557 val |= (config_params->lpf_enable & CCDC_LPF_MASK) <<
560 /* Configure the data shift */
561 val |= (config_params->datasft & CCDC_DATASFT_MASK) <<
564 dev_dbg(ccdc_cfg.dev, "\nWriting 0x%x to MODESET...\n", val);
566 /* Configure the Median Filter threshold */
567 regw((config_params->med_filt_thres) & CCDC_MED_FILT_THRESH, MEDFILT);
569 /* Configure GAMMAWD register. defaur 11-2, and Mosaic cfa pattern */
570 val = CCDC_GAMMA_BITS_11_2 << CCDC_GAMMAWD_INPUT_SHIFT |
573 /* Enable and configure aLaw register if needed */
574 if (config_params->alaw.enable) {
575 val |= (CCDC_ALAW_ENABLE |
576 ((config_params->alaw.gamma_wd &
577 CCDC_ALAW_GAMMA_WD_MASK) <<
578 CCDC_GAMMAWD_INPUT_SHIFT));
581 /* Configure Median filter1 & filter2 */
582 val |= ((config_params->mfilt1 << CCDC_MFILT1_SHIFT) |
583 (config_params->mfilt2 << CCDC_MFILT2_SHIFT));
586 dev_dbg(ccdc_cfg.dev, "\nWriting 0x%x to GAMMAWD...\n", val);
588 /* configure video window */
589 ccdc_setwin(¶ms->win, params->frm_fmt, 1);
591 /* Optical Clamp Averaging */
592 ccdc_config_black_clamp(&config_params->blk_clamp);
594 /* Black level compensation */
595 ccdc_config_black_compense(&config_params->blk_comp);
597 /* Vertical Defect Correction if needed */
598 if (ccdc_config_vdfc(&config_params->vertical_dft) < 0)
601 /* color space conversion */
602 ccdc_config_csc(&config_params->csc);
605 ccdc_config_color_patterns(&config_params->col_pat_field0,
606 &config_params->col_pat_field1);
608 /* Configure the Gain & offset control */
609 ccdc_config_gain_offset();
611 dev_dbg(ccdc_cfg.dev, "\nWriting %x to COLPTN...\n", val);
613 /* Configure DATAOFST register */
614 val = (config_params->data_offset.horz_offset & CCDC_DATAOFST_MASK) <<
615 CCDC_DATAOFST_H_SHIFT;
616 val |= (config_params->data_offset.vert_offset & CCDC_DATAOFST_MASK) <<
617 CCDC_DATAOFST_V_SHIFT;
620 /* configuring HSIZE register */
621 val = (params->horz_flip_enable & CCDC_HSIZE_FLIP_MASK) <<
622 CCDC_HSIZE_FLIP_SHIFT;
624 /* If pack 8 is enable then 1 pixel will take 1 byte */
625 if ((config_params->data_sz == CCDC_DATA_8BITS) ||
626 config_params->alaw.enable) {
627 val |= (((params->win.width) + 31) >> 5) &
630 /* adjust to multiple of 32 */
631 dev_dbg(ccdc_cfg.dev, "\nWriting 0x%x to HSIZE...\n",
632 (((params->win.width) + 31) >> 5) &
633 CCDC_HSIZE_VAL_MASK);
635 /* else one pixel will take 2 byte */
636 val |= (((params->win.width * 2) + 31) >> 5) &
639 dev_dbg(ccdc_cfg.dev, "\nWriting 0x%x to HSIZE...\n",
640 (((params->win.width * 2) + 31) >> 5) &
641 CCDC_HSIZE_VAL_MASK);
645 /* Configure SDOFST register */
646 if (params->frm_fmt == CCDC_FRMFMT_INTERLACED) {
647 if (params->image_invert_enable) {
648 /* For interlace inverse mode */
649 regw(CCDC_SDOFST_INTERLACE_INVERSE, SDOFST);
650 dev_dbg(ccdc_cfg.dev, "\nWriting %x to SDOFST...\n",
651 CCDC_SDOFST_INTERLACE_INVERSE);
653 /* For interlace non inverse mode */
654 regw(CCDC_SDOFST_INTERLACE_NORMAL, SDOFST);
655 dev_dbg(ccdc_cfg.dev, "\nWriting %x to SDOFST...\n",
656 CCDC_SDOFST_INTERLACE_NORMAL);
658 } else if (params->frm_fmt == CCDC_FRMFMT_PROGRESSIVE) {
659 if (params->image_invert_enable) {
660 /* For progessive inverse mode */
661 regw(CCDC_SDOFST_PROGRESSIVE_INVERSE, SDOFST);
662 dev_dbg(ccdc_cfg.dev, "\nWriting %x to SDOFST...\n",
663 CCDC_SDOFST_PROGRESSIVE_INVERSE);
665 /* For progessive non inverse mode */
666 regw(CCDC_SDOFST_PROGRESSIVE_NORMAL, SDOFST);
667 dev_dbg(ccdc_cfg.dev, "\nWriting %x to SDOFST...\n",
668 CCDC_SDOFST_PROGRESSIVE_NORMAL);
671 dev_dbg(ccdc_cfg.dev, "\nend of ccdc_config_raw...");
675 static int ccdc_configure(void)
677 if (ccdc_cfg.if_type == VPFE_RAW_BAYER)
678 return ccdc_config_raw();
684 static int ccdc_set_buftype(enum ccdc_buftype buf_type)
686 if (ccdc_cfg.if_type == VPFE_RAW_BAYER)
687 ccdc_cfg.bayer.buf_type = buf_type;
689 ccdc_cfg.ycbcr.buf_type = buf_type;
692 static enum ccdc_buftype ccdc_get_buftype(void)
694 if (ccdc_cfg.if_type == VPFE_RAW_BAYER)
695 return ccdc_cfg.bayer.buf_type;
696 return ccdc_cfg.ycbcr.buf_type;
699 static int ccdc_enum_pix(u32 *pix, int i)
702 if (ccdc_cfg.if_type == VPFE_RAW_BAYER) {
703 if (i < ARRAY_SIZE(ccdc_raw_bayer_pix_formats)) {
704 *pix = ccdc_raw_bayer_pix_formats[i];
708 if (i < ARRAY_SIZE(ccdc_raw_yuv_pix_formats)) {
709 *pix = ccdc_raw_yuv_pix_formats[i];
716 static int ccdc_set_pixel_format(u32 pixfmt)
718 struct ccdc_a_law *alaw = &ccdc_cfg.bayer.config_params.alaw;
720 if (ccdc_cfg.if_type == VPFE_RAW_BAYER) {
721 ccdc_cfg.bayer.pix_fmt = CCDC_PIXFMT_RAW;
722 if (pixfmt == V4L2_PIX_FMT_SBGGR8)
724 else if (pixfmt != V4L2_PIX_FMT_SBGGR16)
727 if (pixfmt == V4L2_PIX_FMT_YUYV)
728 ccdc_cfg.ycbcr.pix_order = CCDC_PIXORDER_YCBYCR;
729 else if (pixfmt == V4L2_PIX_FMT_UYVY)
730 ccdc_cfg.ycbcr.pix_order = CCDC_PIXORDER_CBYCRY;
736 static u32 ccdc_get_pixel_format(void)
738 struct ccdc_a_law *alaw = &ccdc_cfg.bayer.config_params.alaw;
741 if (ccdc_cfg.if_type == VPFE_RAW_BAYER)
743 pixfmt = V4L2_PIX_FMT_SBGGR8;
745 pixfmt = V4L2_PIX_FMT_SBGGR16;
747 if (ccdc_cfg.ycbcr.pix_order == CCDC_PIXORDER_YCBYCR)
748 pixfmt = V4L2_PIX_FMT_YUYV;
750 pixfmt = V4L2_PIX_FMT_UYVY;
754 static int ccdc_set_image_window(struct v4l2_rect *win)
756 if (ccdc_cfg.if_type == VPFE_RAW_BAYER)
757 ccdc_cfg.bayer.win = *win;
759 ccdc_cfg.ycbcr.win = *win;
763 static void ccdc_get_image_window(struct v4l2_rect *win)
765 if (ccdc_cfg.if_type == VPFE_RAW_BAYER)
766 *win = ccdc_cfg.bayer.win;
768 *win = ccdc_cfg.ycbcr.win;
771 static unsigned int ccdc_get_line_length(void)
773 struct ccdc_config_params_raw *config_params =
774 &ccdc_cfg.bayer.config_params;
777 if (ccdc_cfg.if_type == VPFE_RAW_BAYER) {
778 if ((config_params->alaw.enable) ||
779 (config_params->data_sz == CCDC_DATA_8BITS))
780 len = ccdc_cfg.bayer.win.width;
782 len = ccdc_cfg.bayer.win.width * 2;
784 len = ccdc_cfg.ycbcr.win.width * 2;
785 return ALIGN(len, 32);
788 static int ccdc_set_frame_format(enum ccdc_frmfmt frm_fmt)
790 if (ccdc_cfg.if_type == VPFE_RAW_BAYER)
791 ccdc_cfg.bayer.frm_fmt = frm_fmt;
793 ccdc_cfg.ycbcr.frm_fmt = frm_fmt;
797 static enum ccdc_frmfmt ccdc_get_frame_format(void)
799 if (ccdc_cfg.if_type == VPFE_RAW_BAYER)
800 return ccdc_cfg.bayer.frm_fmt;
802 return ccdc_cfg.ycbcr.frm_fmt;
805 static int ccdc_getfid(void)
807 return (regr(MODESET) >> 15) & 1;
810 /* misc operations */
811 static inline void ccdc_setfbaddr(unsigned long addr)
813 regw((addr >> 21) & 0x007f, STADRH);
814 regw((addr >> 5) & 0x0ffff, STADRL);
817 static int ccdc_set_hw_if_params(struct vpfe_hw_if_param *params)
819 ccdc_cfg.if_type = params->if_type;
821 switch (params->if_type) {
823 case VPFE_YCBCR_SYNC_16:
824 case VPFE_YCBCR_SYNC_8:
825 ccdc_cfg.ycbcr.vd_pol = params->vdpol;
826 ccdc_cfg.ycbcr.hd_pol = params->hdpol;
829 /* TODO add support for raw bayer here */
835 static const struct ccdc_hw_device ccdc_hw_dev = {
836 .name = "DM355 CCDC",
837 .owner = THIS_MODULE,
841 .enable = ccdc_enable,
842 .enable_out_to_sdram = ccdc_enable_output_to_sdram,
843 .set_hw_if_params = ccdc_set_hw_if_params,
844 .configure = ccdc_configure,
845 .set_buftype = ccdc_set_buftype,
846 .get_buftype = ccdc_get_buftype,
847 .enum_pix = ccdc_enum_pix,
848 .set_pixel_format = ccdc_set_pixel_format,
849 .get_pixel_format = ccdc_get_pixel_format,
850 .set_frame_format = ccdc_set_frame_format,
851 .get_frame_format = ccdc_get_frame_format,
852 .set_image_window = ccdc_set_image_window,
853 .get_image_window = ccdc_get_image_window,
854 .get_line_length = ccdc_get_line_length,
855 .setfbaddr = ccdc_setfbaddr,
856 .getfid = ccdc_getfid,
860 static int dm355_ccdc_probe(struct platform_device *pdev)
862 void (*setup_pinmux)(void);
863 struct resource *res;
867 * first try to register with vpfe. If not correct platform, then we
868 * don't have to iomap
870 status = vpfe_register_ccdc_device(&ccdc_hw_dev);
874 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
880 res = request_mem_region(res->start, resource_size(res), res->name);
886 ccdc_cfg.base_addr = ioremap(res->start, resource_size(res));
887 if (!ccdc_cfg.base_addr) {
892 /* Platform data holds setup_pinmux function ptr */
893 if (NULL == pdev->dev.platform_data) {
897 setup_pinmux = pdev->dev.platform_data;
899 * setup Mux configuration for ccdc which may be different for
900 * different SoCs using this CCDC
903 ccdc_cfg.dev = &pdev->dev;
904 printk(KERN_NOTICE "%s is registered with vpfe.\n", ccdc_hw_dev.name);
907 iounmap(ccdc_cfg.base_addr);
909 release_mem_region(res->start, resource_size(res));
911 vpfe_unregister_ccdc_device(&ccdc_hw_dev);
915 static int dm355_ccdc_remove(struct platform_device *pdev)
917 struct resource *res;
919 iounmap(ccdc_cfg.base_addr);
920 res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
922 release_mem_region(res->start, resource_size(res));
923 vpfe_unregister_ccdc_device(&ccdc_hw_dev);
927 static struct platform_driver dm355_ccdc_driver = {
929 .name = "dm355_ccdc",
931 .remove = dm355_ccdc_remove,
932 .probe = dm355_ccdc_probe,
935 module_platform_driver(dm355_ccdc_driver);