drivers/clk/clk-u300.c

   1 /*
   2  * U300 clock implementation
   3  * Copyright (C) 2007-2012 ST-Ericsson AB
   4  * License terms: GNU General Public License (GPL) version 2
   5  * Author: Linus Walleij <linus.walleij@stericsson.com>
   6  * Author: Jonas Aaberg <jonas.aberg@stericsson.com>
   7  */
   8 #include <linux/clkdev.h>
   9 #include <linux/slab.h>
  10 #include <linux/err.h>
  11 #include <linux/io.h>
  12 #include <linux/clk-provider.h>
  13 #include <linux/spinlock.h>
  14 #include <linux/of.h>
  15 #include <linux/platform_data/clk-u300.h>
  16
  17 /* APP side SYSCON registers */
  18 /* CLK Control Register 16bit (R/W) */
  19 #define U300_SYSCON_CCR                                         (0x0000)
  20 #define U300_SYSCON_CCR_I2S1_USE_VCXO                           (0x0040)
  21 #define U300_SYSCON_CCR_I2S0_USE_VCXO                           (0x0020)
  22 #define U300_SYSCON_CCR_TURN_VCXO_ON                            (0x0008)
  23 #define U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK                 (0x0007)
  24 #define U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER            (0x04)
  25 #define U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW                  (0x03)
  26 #define U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE         (0x02)
  27 #define U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH                 (0x01)
  28 #define U300_SYSCON_CCR_CLKING_PERFORMANCE_BEST                 (0x00)
  29 /* CLK Status Register 16bit (R/W) */
  30 #define U300_SYSCON_CSR                                         (0x0004)
  31 #define U300_SYSCON_CSR_PLL208_LOCK_IND                         (0x0002)
  32 #define U300_SYSCON_CSR_PLL13_LOCK_IND                          (0x0001)
  33 /* Reset lines for SLOW devices 16bit (R/W) */
  34 #define U300_SYSCON_RSR                                         (0x0014)
  35 #define U300_SYSCON_RSR_PPM_RESET_EN                            (0x0200)
  36 #define U300_SYSCON_RSR_ACC_TMR_RESET_EN                        (0x0100)
  37 #define U300_SYSCON_RSR_APP_TMR_RESET_EN                        (0x0080)
  38 #define U300_SYSCON_RSR_RTC_RESET_EN                            (0x0040)
  39 #define U300_SYSCON_RSR_KEYPAD_RESET_EN                         (0x0020)
  40 #define U300_SYSCON_RSR_GPIO_RESET_EN                           (0x0010)
  41 #define U300_SYSCON_RSR_EH_RESET_EN                             (0x0008)
  42 #define U300_SYSCON_RSR_BTR_RESET_EN                            (0x0004)
  43 #define U300_SYSCON_RSR_UART_RESET_EN                           (0x0002)
  44 #define U300_SYSCON_RSR_SLOW_BRIDGE_RESET_EN                    (0x0001)
  45 /* Reset lines for FAST devices 16bit (R/W) */
  46 #define U300_SYSCON_RFR                                         (0x0018)
  47 #define U300_SYSCON_RFR_UART1_RESET_ENABLE                      (0x0080)
  48 #define U300_SYSCON_RFR_SPI_RESET_ENABLE                        (0x0040)
  49 #define U300_SYSCON_RFR_MMC_RESET_ENABLE                        (0x0020)
  50 #define U300_SYSCON_RFR_PCM_I2S1_RESET_ENABLE                   (0x0010)
  51 #define U300_SYSCON_RFR_PCM_I2S0_RESET_ENABLE                   (0x0008)
  52 #define U300_SYSCON_RFR_I2C1_RESET_ENABLE                       (0x0004)
  53 #define U300_SYSCON_RFR_I2C0_RESET_ENABLE                       (0x0002)
  54 #define U300_SYSCON_RFR_FAST_BRIDGE_RESET_ENABLE                (0x0001)
  55 /* Reset lines for the rest of the peripherals 16bit (R/W) */
  56 #define U300_SYSCON_RRR                                         (0x001c)
  57 #define U300_SYSCON_RRR_CDS_RESET_EN                            (0x4000)
  58 #define U300_SYSCON_RRR_ISP_RESET_EN                            (0x2000)
  59 #define U300_SYSCON_RRR_INTCON_RESET_EN                         (0x1000)
  60 #define U300_SYSCON_RRR_MSPRO_RESET_EN                          (0x0800)
  61 #define U300_SYSCON_RRR_XGAM_RESET_EN                           (0x0100)
  62 #define U300_SYSCON_RRR_XGAM_VC_SYNC_RESET_EN                   (0x0080)
  63 #define U300_SYSCON_RRR_NANDIF_RESET_EN                         (0x0040)
  64 #define U300_SYSCON_RRR_EMIF_RESET_EN                           (0x0020)
  65 #define U300_SYSCON_RRR_DMAC_RESET_EN                           (0x0010)
  66 #define U300_SYSCON_RRR_CPU_RESET_EN                            (0x0008)
  67 #define U300_SYSCON_RRR_APEX_RESET_EN                           (0x0004)
  68 #define U300_SYSCON_RRR_AHB_RESET_EN                            (0x0002)
  69 #define U300_SYSCON_RRR_AAIF_RESET_EN                           (0x0001)
  70 /* Clock enable for SLOW peripherals 16bit (R/W) */
  71 #define U300_SYSCON_CESR                                        (0x0020)
  72 #define U300_SYSCON_CESR_PPM_CLK_EN                             (0x0200)
  73 #define U300_SYSCON_CESR_ACC_TMR_CLK_EN                         (0x0100)
  74 #define U300_SYSCON_CESR_APP_TMR_CLK_EN                         (0x0080)
  75 #define U300_SYSCON_CESR_KEYPAD_CLK_EN                          (0x0040)
  76 #define U300_SYSCON_CESR_GPIO_CLK_EN                            (0x0010)
  77 #define U300_SYSCON_CESR_EH_CLK_EN                              (0x0008)
  78 #define U300_SYSCON_CESR_BTR_CLK_EN                             (0x0004)
  79 #define U300_SYSCON_CESR_UART_CLK_EN                            (0x0002)
  80 #define U300_SYSCON_CESR_SLOW_BRIDGE_CLK_EN                     (0x0001)
  81 /* Clock enable for FAST peripherals 16bit (R/W) */
  82 #define U300_SYSCON_CEFR                                        (0x0024)
  83 #define U300_SYSCON_CEFR_UART1_CLK_EN                           (0x0200)
  84 #define U300_SYSCON_CEFR_I2S1_CORE_CLK_EN                       (0x0100)
  85 #define U300_SYSCON_CEFR_I2S0_CORE_CLK_EN                       (0x0080)
  86 #define U300_SYSCON_CEFR_SPI_CLK_EN                             (0x0040)
  87 #define U300_SYSCON_CEFR_MMC_CLK_EN                             (0x0020)
  88 #define U300_SYSCON_CEFR_I2S1_CLK_EN                            (0x0010)
  89 #define U300_SYSCON_CEFR_I2S0_CLK_EN                            (0x0008)
  90 #define U300_SYSCON_CEFR_I2C1_CLK_EN                            (0x0004)
  91 #define U300_SYSCON_CEFR_I2C0_CLK_EN                            (0x0002)
  92 #define U300_SYSCON_CEFR_FAST_BRIDGE_CLK_EN                     (0x0001)
  93 /* Clock enable for the rest of the peripherals 16bit (R/W) */
  94 #define U300_SYSCON_CERR                                        (0x0028)
  95 #define U300_SYSCON_CERR_CDS_CLK_EN                             (0x2000)
  96 #define U300_SYSCON_CERR_ISP_CLK_EN                             (0x1000)
  97 #define U300_SYSCON_CERR_MSPRO_CLK_EN                           (0x0800)
  98 #define U300_SYSCON_CERR_AHB_SUBSYS_BRIDGE_CLK_EN               (0x0400)
  99 #define U300_SYSCON_CERR_SEMI_CLK_EN                            (0x0200)
 100 #define U300_SYSCON_CERR_XGAM_CLK_EN                            (0x0100)
 101 #define U300_SYSCON_CERR_VIDEO_ENC_CLK_EN                       (0x0080)
 102 #define U300_SYSCON_CERR_NANDIF_CLK_EN                          (0x0040)
 103 #define U300_SYSCON_CERR_EMIF_CLK_EN                            (0x0020)
 104 #define U300_SYSCON_CERR_DMAC_CLK_EN                            (0x0010)
 105 #define U300_SYSCON_CERR_CPU_CLK_EN                             (0x0008)
 106 #define U300_SYSCON_CERR_APEX_CLK_EN                            (0x0004)
 107 #define U300_SYSCON_CERR_AHB_CLK_EN                             (0x0002)
 108 #define U300_SYSCON_CERR_AAIF_CLK_EN                            (0x0001)
 109 /* Single block clock enable 16bit (-/W) */
 110 #define U300_SYSCON_SBCER                                       (0x002c)
 111 #define U300_SYSCON_SBCER_PPM_CLK_EN                            (0x0009)
 112 #define U300_SYSCON_SBCER_ACC_TMR_CLK_EN                        (0x0008)
 113 #define U300_SYSCON_SBCER_APP_TMR_CLK_EN                        (0x0007)
 114 #define U300_SYSCON_SBCER_KEYPAD_CLK_EN                         (0x0006)
 115 #define U300_SYSCON_SBCER_GPIO_CLK_EN                           (0x0004)
 116 #define U300_SYSCON_SBCER_EH_CLK_EN                             (0x0003)
 117 #define U300_SYSCON_SBCER_BTR_CLK_EN                            (0x0002)
 118 #define U300_SYSCON_SBCER_UART_CLK_EN                           (0x0001)
 119 #define U300_SYSCON_SBCER_SLOW_BRIDGE_CLK_EN                    (0x0000)
 120 #define U300_SYSCON_SBCER_UART1_CLK_EN                          (0x0019)
 121 #define U300_SYSCON_SBCER_I2S1_CORE_CLK_EN                      (0x0018)
 122 #define U300_SYSCON_SBCER_I2S0_CORE_CLK_EN                      (0x0017)
 123 #define U300_SYSCON_SBCER_SPI_CLK_EN                            (0x0016)
 124 #define U300_SYSCON_SBCER_MMC_CLK_EN                            (0x0015)
 125 #define U300_SYSCON_SBCER_I2S1_CLK_EN                           (0x0014)
 126 #define U300_SYSCON_SBCER_I2S0_CLK_EN                           (0x0013)
 127 #define U300_SYSCON_SBCER_I2C1_CLK_EN                           (0x0012)
 128 #define U300_SYSCON_SBCER_I2C0_CLK_EN                           (0x0011)
 129 #define U300_SYSCON_SBCER_FAST_BRIDGE_CLK_EN                    (0x0010)
 130 #define U300_SYSCON_SBCER_CDS_CLK_EN                            (0x002D)
 131 #define U300_SYSCON_SBCER_ISP_CLK_EN                            (0x002C)
 132 #define U300_SYSCON_SBCER_MSPRO_CLK_EN                          (0x002B)
 133 #define U300_SYSCON_SBCER_AHB_SUBSYS_BRIDGE_CLK_EN              (0x002A)
 134 #define U300_SYSCON_SBCER_SEMI_CLK_EN                           (0x0029)
 135 #define U300_SYSCON_SBCER_XGAM_CLK_EN                           (0x0028)
 136 #define U300_SYSCON_SBCER_VIDEO_ENC_CLK_EN                      (0x0027)
 137 #define U300_SYSCON_SBCER_NANDIF_CLK_EN                         (0x0026)
 138 #define U300_SYSCON_SBCER_EMIF_CLK_EN                           (0x0025)
 139 #define U300_SYSCON_SBCER_DMAC_CLK_EN                           (0x0024)
 140 #define U300_SYSCON_SBCER_CPU_CLK_EN                            (0x0023)
 141 #define U300_SYSCON_SBCER_APEX_CLK_EN                           (0x0022)
 142 #define U300_SYSCON_SBCER_AHB_CLK_EN                            (0x0021)
 143 #define U300_SYSCON_SBCER_AAIF_CLK_EN                           (0x0020)
 144 /* Single block clock disable 16bit (-/W) */
 145 #define U300_SYSCON_SBCDR                                       (0x0030)
 146 /* Same values as above for SBCER */
 147 /* Clock force SLOW peripherals 16bit (R/W) */
 148 #define U300_SYSCON_CFSR                                        (0x003c)
 149 #define U300_SYSCON_CFSR_PPM_CLK_FORCE_EN                       (0x0200)
 150 #define U300_SYSCON_CFSR_ACC_TMR_CLK_FORCE_EN                   (0x0100)
 151 #define U300_SYSCON_CFSR_APP_TMR_CLK_FORCE_EN                   (0x0080)
 152 #define U300_SYSCON_CFSR_KEYPAD_CLK_FORCE_EN                    (0x0020)
 153 #define U300_SYSCON_CFSR_GPIO_CLK_FORCE_EN                      (0x0010)
 154 #define U300_SYSCON_CFSR_EH_CLK_FORCE_EN                        (0x0008)
 155 #define U300_SYSCON_CFSR_BTR_CLK_FORCE_EN                       (0x0004)
 156 #define U300_SYSCON_CFSR_UART_CLK_FORCE_EN                      (0x0002)
 157 #define U300_SYSCON_CFSR_SLOW_BRIDGE_CLK_FORCE_EN               (0x0001)
 158 /* Clock force FAST peripherals 16bit (R/W) */
 159 #define U300_SYSCON_CFFR                                        (0x40)
 160 /* Values not defined. Define if you want to use them. */
 161 /* Clock force the rest of the peripherals 16bit (R/W) */
 162 #define U300_SYSCON_CFRR                                        (0x44)
 163 #define U300_SYSCON_CFRR_CDS_CLK_FORCE_EN                       (0x2000)
 164 #define U300_SYSCON_CFRR_ISP_CLK_FORCE_EN                       (0x1000)
 165 #define U300_SYSCON_CFRR_MSPRO_CLK_FORCE_EN                     (0x0800)
 166 #define U300_SYSCON_CFRR_AHB_SUBSYS_BRIDGE_CLK_FORCE_EN         (0x0400)
 167 #define U300_SYSCON_CFRR_SEMI_CLK_FORCE_EN                      (0x0200)
 168 #define U300_SYSCON_CFRR_XGAM_CLK_FORCE_EN                      (0x0100)
 169 #define U300_SYSCON_CFRR_VIDEO_ENC_CLK_FORCE_EN                 (0x0080)
 170 #define U300_SYSCON_CFRR_NANDIF_CLK_FORCE_EN                    (0x0040)
 171 #define U300_SYSCON_CFRR_EMIF_CLK_FORCE_EN                      (0x0020)
 172 #define U300_SYSCON_CFRR_DMAC_CLK_FORCE_EN                      (0x0010)
 173 #define U300_SYSCON_CFRR_CPU_CLK_FORCE_EN                       (0x0008)
 174 #define U300_SYSCON_CFRR_APEX_CLK_FORCE_EN                      (0x0004)
 175 #define U300_SYSCON_CFRR_AHB_CLK_FORCE_EN                       (0x0002)
 176 #define U300_SYSCON_CFRR_AAIF_CLK_FORCE_EN                      (0x0001)
 177 /* PLL208 Frequency Control 16bit (R/W) */
 178 #define U300_SYSCON_PFCR                                        (0x48)
 179 #define U300_SYSCON_PFCR_DPLL_MULT_NUM                          (0x000F)
 180 /* Power Management Control 16bit (R/W) */
 181 #define U300_SYSCON_PMCR                                        (0x50)
 182 #define U300_SYSCON_PMCR_DCON_ENABLE                            (0x0002)
 183 #define U300_SYSCON_PMCR_PWR_MGNT_ENABLE                        (0x0001)
 184 /* Reset Out 16bit (R/W) */
 185 #define U300_SYSCON_RCR                                         (0x6c)
 186 #define U300_SYSCON_RCR_RESOUT0_RST_N_DISABLE                   (0x0001)
 187 /* EMIF Slew Rate Control 16bit (R/W) */
 188 #define U300_SYSCON_SRCLR                                       (0x70)
 189 #define U300_SYSCON_SRCLR_MASK                                  (0x03FF)
 190 #define U300_SYSCON_SRCLR_VALUE                                 (0x03FF)
 191 #define U300_SYSCON_SRCLR_EMIF_1_SLRC_5_B                       (0x0200)
 192 #define U300_SYSCON_SRCLR_EMIF_1_SLRC_5_A                       (0x0100)
 193 #define U300_SYSCON_SRCLR_EMIF_1_SLRC_4_B                       (0x0080)
 194 #define U300_SYSCON_SRCLR_EMIF_1_SLRC_4_A                       (0x0040)
 195 #define U300_SYSCON_SRCLR_EMIF_1_SLRC_3_B                       (0x0020)
 196 #define U300_SYSCON_SRCLR_EMIF_1_SLRC_3_A                       (0x0010)
 197 #define U300_SYSCON_SRCLR_EMIF_1_SLRC_2_B                       (0x0008)
 198 #define U300_SYSCON_SRCLR_EMIF_1_SLRC_2_A                       (0x0004)
 199 #define U300_SYSCON_SRCLR_EMIF_1_SLRC_1_B                       (0x0002)
 200 #define U300_SYSCON_SRCLR_EMIF_1_SLRC_1_A                       (0x0001)
 201 /* EMIF Clock Control Register 16bit (R/W) */
 202 #define U300_SYSCON_ECCR                                        (0x0078)
 203 #define U300_SYSCON_ECCR_MASK                                   (0x000F)
 204 #define U300_SYSCON_ECCR_EMIF_1_STATIC_CLK_EN_N_DISABLE         (0x0008)
 205 #define U300_SYSCON_ECCR_EMIF_1_RET_OUT_CLK_EN_N_DISABLE        (0x0004)
 206 #define U300_SYSCON_ECCR_EMIF_MEMCLK_RET_EN_N_DISABLE           (0x0002)
 207 #define U300_SYSCON_ECCR_EMIF_SDRCLK_RET_EN_N_DISABLE           (0x0001)
 208 /* MMC/MSPRO frequency divider register 0 16bit (R/W) */
 209 #define U300_SYSCON_MMF0R                                       (0x90)
 210 #define U300_SYSCON_MMF0R_MASK                                  (0x00FF)
 211 #define U300_SYSCON_MMF0R_FREQ_0_HIGH_MASK                      (0x00F0)
 212 #define U300_SYSCON_MMF0R_FREQ_0_LOW_MASK                       (0x000F)
 213 /* MMC/MSPRO frequency divider register 1 16bit (R/W) */
 214 #define U300_SYSCON_MMF1R                                       (0x94)
 215 #define U300_SYSCON_MMF1R_MASK                                  (0x00FF)
 216 #define U300_SYSCON_MMF1R_FREQ_1_HIGH_MASK                      (0x00F0)
 217 #define U300_SYSCON_MMF1R_FREQ_1_LOW_MASK                       (0x000F)
 218 /* Clock control for the MMC and MSPRO blocks 16bit (R/W) */
 219 #define U300_SYSCON_MMCR                                        (0x9C)
 220 #define U300_SYSCON_MMCR_MASK                                   (0x0003)
 221 #define U300_SYSCON_MMCR_MMC_FB_CLK_SEL_ENABLE                  (0x0002)
 222 #define U300_SYSCON_MMCR_MSPRO_FREQSEL_ENABLE                   (0x0001)
 223 /* SYS_0_CLK_CONTROL first clock control 16bit (R/W) */
 224 #define U300_SYSCON_S0CCR                                       (0x120)
 225 #define U300_SYSCON_S0CCR_FIELD_MASK                            (0x43FF)
 226 #define U300_SYSCON_S0CCR_CLOCK_REQ                             (0x4000)
 227 #define U300_SYSCON_S0CCR_CLOCK_REQ_MONITOR                     (0x2000)
 228 #define U300_SYSCON_S0CCR_CLOCK_INV                             (0x0200)
 229 #define U300_SYSCON_S0CCR_CLOCK_FREQ_MASK                       (0x01E0)
 230 #define U300_SYSCON_S0CCR_CLOCK_SELECT_MASK                     (0x001E)
 231 #define U300_SYSCON_S0CCR_CLOCK_ENABLE                          (0x0001)
 232 #define U300_SYSCON_S0CCR_SEL_MCLK                              (0x8<<1)
 233 #define U300_SYSCON_S0CCR_SEL_ACC_FSM_CLK                       (0xA<<1)
 234 #define U300_SYSCON_S0CCR_SEL_PLL60_48_CLK                      (0xC<<1)
 235 #define U300_SYSCON_S0CCR_SEL_PLL60_60_CLK                      (0xD<<1)
 236 #define U300_SYSCON_S0CCR_SEL_ACC_PLL208_CLK                    (0xE<<1)
 237 #define U300_SYSCON_S0CCR_SEL_APP_PLL13_CLK                     (0x0<<1)
 238 #define U300_SYSCON_S0CCR_SEL_APP_FSM_CLK                       (0x2<<1)
 239 #define U300_SYSCON_S0CCR_SEL_RTC_CLK                           (0x4<<1)
 240 #define U300_SYSCON_S0CCR_SEL_APP_PLL208_CLK                    (0x6<<1)
 241 /* SYS_1_CLK_CONTROL second clock control 16 bit (R/W) */
 242 #define U300_SYSCON_S1CCR                                       (0x124)
 243 #define U300_SYSCON_S1CCR_FIELD_MASK                            (0x43FF)
 244 #define U300_SYSCON_S1CCR_CLOCK_REQ                             (0x4000)
 245 #define U300_SYSCON_S1CCR_CLOCK_REQ_MONITOR                     (0x2000)
 246 #define U300_SYSCON_S1CCR_CLOCK_INV                             (0x0200)
 247 #define U300_SYSCON_S1CCR_CLOCK_FREQ_MASK                       (0x01E0)
 248 #define U300_SYSCON_S1CCR_CLOCK_SELECT_MASK                     (0x001E)
 249 #define U300_SYSCON_S1CCR_CLOCK_ENABLE                          (0x0001)
 250 #define U300_SYSCON_S1CCR_SEL_MCLK                              (0x8<<1)
 251 #define U300_SYSCON_S1CCR_SEL_ACC_FSM_CLK                       (0xA<<1)
 252 #define U300_SYSCON_S1CCR_SEL_PLL60_48_CLK                      (0xC<<1)
 253 #define U300_SYSCON_S1CCR_SEL_PLL60_60_CLK                      (0xD<<1)
 254 #define U300_SYSCON_S1CCR_SEL_ACC_PLL208_CLK                    (0xE<<1)
 255 #define U300_SYSCON_S1CCR_SEL_ACC_PLL13_CLK                     (0x0<<1)
 256 #define U300_SYSCON_S1CCR_SEL_APP_FSM_CLK                       (0x2<<1)
 257 #define U300_SYSCON_S1CCR_SEL_RTC_CLK                           (0x4<<1)
 258 #define U300_SYSCON_S1CCR_SEL_APP_PLL208_CLK                    (0x6<<1)
 259 /* SYS_2_CLK_CONTROL third clock contol 16 bit (R/W) */
 260 #define U300_SYSCON_S2CCR                                       (0x128)
 261 #define U300_SYSCON_S2CCR_FIELD_MASK                            (0xC3FF)
 262 #define U300_SYSCON_S2CCR_CLK_STEAL                             (0x8000)
 263 #define U300_SYSCON_S2CCR_CLOCK_REQ                             (0x4000)
 264 #define U300_SYSCON_S2CCR_CLOCK_REQ_MONITOR                     (0x2000)
 265 #define U300_SYSCON_S2CCR_CLOCK_INV                             (0x0200)
 266 #define U300_SYSCON_S2CCR_CLOCK_FREQ_MASK                       (0x01E0)
 267 #define U300_SYSCON_S2CCR_CLOCK_SELECT_MASK                     (0x001E)
 268 #define U300_SYSCON_S2CCR_CLOCK_ENABLE                          (0x0001)
 269 #define U300_SYSCON_S2CCR_SEL_MCLK                              (0x8<<1)
 270 #define U300_SYSCON_S2CCR_SEL_ACC_FSM_CLK                       (0xA<<1)
 271 #define U300_SYSCON_S2CCR_SEL_PLL60_48_CLK                      (0xC<<1)
 272 #define U300_SYSCON_S2CCR_SEL_PLL60_60_CLK                      (0xD<<1)
 273 #define U300_SYSCON_S2CCR_SEL_ACC_PLL208_CLK                    (0xE<<1)
 274 #define U300_SYSCON_S2CCR_SEL_ACC_PLL13_CLK                     (0x0<<1)
 275 #define U300_SYSCON_S2CCR_SEL_APP_FSM_CLK                       (0x2<<1)
 276 #define U300_SYSCON_S2CCR_SEL_RTC_CLK                           (0x4<<1)
 277 #define U300_SYSCON_S2CCR_SEL_APP_PLL208_CLK                    (0x6<<1)
 278 /* SC_PLL_IRQ_CONTROL 16bit (R/W) */
 279 #define U300_SYSCON_PICR                                        (0x0130)
 280 #define U300_SYSCON_PICR_MASK                                   (0x00FF)
 281 #define U300_SYSCON_PICR_FORCE_PLL208_LOCK_LOW_ENABLE           (0x0080)
 282 #define U300_SYSCON_PICR_FORCE_PLL208_LOCK_HIGH_ENABLE          (0x0040)
 283 #define U300_SYSCON_PICR_FORCE_PLL13_LOCK_LOW_ENABLE            (0x0020)
 284 #define U300_SYSCON_PICR_FORCE_PLL13_LOCK_HIGH_ENABLE           (0x0010)
 285 #define U300_SYSCON_PICR_IRQMASK_PLL13_UNLOCK_ENABLE            (0x0008)
 286 #define U300_SYSCON_PICR_IRQMASK_PLL13_LOCK_ENABLE              (0x0004)
 287 #define U300_SYSCON_PICR_IRQMASK_PLL208_UNLOCK_ENABLE           (0x0002)
 288 #define U300_SYSCON_PICR_IRQMASK_PLL208_LOCK_ENABLE             (0x0001)
 289 /* SC_PLL_IRQ_STATUS 16 bit (R/-) */
 290 #define U300_SYSCON_PISR                                        (0x0134)
 291 #define U300_SYSCON_PISR_MASK                                   (0x000F)
 292 #define U300_SYSCON_PISR_PLL13_UNLOCK_IND                       (0x0008)
 293 #define U300_SYSCON_PISR_PLL13_LOCK_IND                         (0x0004)
 294 #define U300_SYSCON_PISR_PLL208_UNLOCK_IND                      (0x0002)
 295 #define U300_SYSCON_PISR_PLL208_LOCK_IND                        (0x0001)
 296 /* SC_PLL_IRQ_CLEAR 16 bit (-/W) */
 297 #define U300_SYSCON_PICLR                                       (0x0138)
 298 #define U300_SYSCON_PICLR_MASK                                  (0x000F)
 299 #define U300_SYSCON_PICLR_RWMASK                                (0x0000)
 300 #define U300_SYSCON_PICLR_PLL13_UNLOCK_SC                       (0x0008)
 301 #define U300_SYSCON_PICLR_PLL13_LOCK_SC                         (0x0004)
 302 #define U300_SYSCON_PICLR_PLL208_UNLOCK_SC                      (0x0002)
 303 #define U300_SYSCON_PICLR_PLL208_LOCK_SC                        (0x0001)
 304 /* Clock activity observability register 0 */
 305 #define U300_SYSCON_C0OAR                                       (0x140)
 306 #define U300_SYSCON_C0OAR_MASK                                  (0xFFFF)
 307 #define U300_SYSCON_C0OAR_VALUE                                 (0xFFFF)
 308 #define U300_SYSCON_C0OAR_BT_H_CLK                              (0x8000)
 309 #define U300_SYSCON_C0OAR_ASPB_P_CLK                            (0x4000)
 310 #define U300_SYSCON_C0OAR_APP_SEMI_H_CLK                        (0x2000)
 311 #define U300_SYSCON_C0OAR_APP_SEMI_CLK                          (0x1000)
 312 #define U300_SYSCON_C0OAR_APP_MMC_MSPRO_CLK                     (0x0800)
 313 #define U300_SYSCON_C0OAR_APP_I2S1_CLK                          (0x0400)
 314 #define U300_SYSCON_C0OAR_APP_I2S0_CLK                          (0x0200)
 315 #define U300_SYSCON_C0OAR_APP_CPU_CLK                           (0x0100)
 316 #define U300_SYSCON_C0OAR_APP_52_CLK                            (0x0080)
 317 #define U300_SYSCON_C0OAR_APP_208_CLK                           (0x0040)
 318 #define U300_SYSCON_C0OAR_APP_104_CLK                           (0x0020)
 319 #define U300_SYSCON_C0OAR_APEX_CLK                              (0x0010)
 320 #define U300_SYSCON_C0OAR_AHPB_M_H_CLK                          (0x0008)
 321 #define U300_SYSCON_C0OAR_AHB_CLK                               (0x0004)
 322 #define U300_SYSCON_C0OAR_AFPB_P_CLK                            (0x0002)
 323 #define U300_SYSCON_C0OAR_AAIF_CLK                              (0x0001)
 324 /* Clock activity observability register 1 */
 325 #define U300_SYSCON_C1OAR                                       (0x144)
 326 #define U300_SYSCON_C1OAR_MASK                                  (0x3FFE)
 327 #define U300_SYSCON_C1OAR_VALUE                                 (0x3FFE)
 328 #define U300_SYSCON_C1OAR_NFIF_F_CLK                            (0x2000)
 329 #define U300_SYSCON_C1OAR_MSPRO_CLK                             (0x1000)
 330 #define U300_SYSCON_C1OAR_MMC_P_CLK                             (0x0800)
 331 #define U300_SYSCON_C1OAR_MMC_CLK                               (0x0400)
 332 #define U300_SYSCON_C1OAR_KP_P_CLK                              (0x0200)
 333 #define U300_SYSCON_C1OAR_I2C1_P_CLK                            (0x0100)
 334 #define U300_SYSCON_C1OAR_I2C0_P_CLK                            (0x0080)
 335 #define U300_SYSCON_C1OAR_GPIO_CLK                              (0x0040)
 336 #define U300_SYSCON_C1OAR_EMIF_MPMC_CLK                         (0x0020)
 337 #define U300_SYSCON_C1OAR_EMIF_H_CLK                            (0x0010)
 338 #define U300_SYSCON_C1OAR_EVHIST_CLK                            (0x0008)
 339 #define U300_SYSCON_C1OAR_PPM_CLK                               (0x0004)
 340 #define U300_SYSCON_C1OAR_DMA_CLK                               (0x0002)
 341 /* Clock activity observability register 2 */
 342 #define U300_SYSCON_C2OAR                                       (0x148)
 343 #define U300_SYSCON_C2OAR_MASK                                  (0x0FFF)
 344 #define U300_SYSCON_C2OAR_VALUE                                 (0x0FFF)
 345 #define U300_SYSCON_C2OAR_XGAM_CDI_CLK                          (0x0800)
 346 #define U300_SYSCON_C2OAR_XGAM_CLK                              (0x0400)
 347 #define U300_SYSCON_C2OAR_VC_H_CLK                              (0x0200)
 348 #define U300_SYSCON_C2OAR_VC_CLK                                (0x0100)
 349 #define U300_SYSCON_C2OAR_UA_P_CLK                              (0x0080)
 350 #define U300_SYSCON_C2OAR_TMR1_CLK                              (0x0040)
 351 #define U300_SYSCON_C2OAR_TMR0_CLK                              (0x0020)
 352 #define U300_SYSCON_C2OAR_SPI_P_CLK                             (0x0010)
 353 #define U300_SYSCON_C2OAR_PCM_I2S1_CORE_CLK                     (0x0008)
 354 #define U300_SYSCON_C2OAR_PCM_I2S1_CLK                          (0x0004)
 355 #define U300_SYSCON_C2OAR_PCM_I2S0_CORE_CLK                     (0x0002)
 356 #define U300_SYSCON_C2OAR_PCM_I2S0_CLK                          (0x0001)
 357
 358
 359 /*
 360  * The clocking hierarchy currently looks like this.
 361  * NOTE: the idea is NOT to show how the clocks are routed on the chip!
 362  * The ideas is to show dependencies, so a clock higher up in the
 363  * hierarchy has to be on in order for another clock to be on. Now,
 364  * both CPU and DMA can actually be on top of the hierarchy, and that
 365  * is not modeled currently. Instead we have the backbone AMBA bus on
 366  * top. This bus cannot be programmed in any way but conceptually it
 367  * needs to be active for the bridges and devices to transport data.
 368  *
 369  * Please be aware that a few clocks are hw controlled, which mean that
 370  * the hw itself can turn on/off or change the rate of the clock when
 371  * needed!
 372  *
 373  *  AMBA bus
 374  *  |
 375  *  +- CPU
 376  *  +- FSMC NANDIF NAND Flash interface
 377  *  +- SEMI Shared Memory interface
 378  *  +- ISP Image Signal Processor (U335 only)
 379  *  +- CDS (U335 only)
 380  *  +- DMA Direct Memory Access Controller
 381  *  +- AAIF APP/ACC Inteface (Mobile Scalable Link, MSL)
 382  *  +- APEX
 383  *  +- VIDEO_ENC AVE2/3 Video Encoder
 384  *  +- XGAM Graphics Accelerator Controller
 385  *  +- AHB
 386  *  |
 387  *  +- ahb:0 AHB Bridge
 388  *  |  |
 389  *  |  +- ahb:1 INTCON Interrupt controller
 390  *  |  +- ahb:3 MSPRO  Memory Stick Pro controller
 391  *  |  +- ahb:4 EMIF   External Memory interface
 392  *  |
 393  *  +- fast:0 FAST bridge
 394  *  |  |
 395  *  |  +- fast:1 MMCSD MMC/SD card reader controller
 396  *  |  +- fast:2 I2S0  PCM I2S channel 0 controller
 397  *  |  +- fast:3 I2S1  PCM I2S channel 1 controller
 398  *  |  +- fast:4 I2C0  I2C channel 0 controller
 399  *  |  +- fast:5 I2C1  I2C channel 1 controller
 400  *  |  +- fast:6 SPI   SPI controller
 401  *  |  +- fast:7 UART1 Secondary UART (U335 only)
 402  *  |
 403  *  +- slow:0 SLOW bridge
 404  *     |
 405  *     +- slow:1 SYSCON (not possible to control)
 406  *     +- slow:2 WDOG Watchdog
 407  *     +- slow:3 UART0 primary UART
 408  *     +- slow:4 TIMER_APP Application timer - used in Linux
 409  *     +- slow:5 KEYPAD controller
 410  *     +- slow:6 GPIO controller
 411  *     +- slow:7 RTC controller
 412  *     +- slow:8 BT Bus Tracer (not used currently)
 413  *     +- slow:9 EH Event Handler (not used currently)
 414  *     +- slow:a TIMER_ACC Access style timer (not used currently)
 415  *     +- slow:b PPM (U335 only, what is that?)
 416  */
 417
 418 /* Global syscon virtual base */
 419 static void __iomem *syscon_vbase;
 420
 421 /**
 422  * struct clk_syscon - U300 syscon clock
 423  * @hw: corresponding clock hardware entry
 424  * @hw_ctrld: whether this clock is hardware controlled (for refcount etc)
 425  *      and does not need any magic pokes to be enabled/disabled
 426  * @reset: state holder, whether this block's reset line is asserted or not
 427  * @res_reg: reset line enable/disable flag register
 428  * @res_bit: bit for resetting or taking this consumer out of reset
 429  * @en_reg: clock line enable/disable flag register
 430  * @en_bit: bit for enabling/disabling this consumer clock line
 431  * @clk_val: magic value to poke in the register to enable/disable
 432  *      this one clock
 433  */
 434 struct clk_syscon {
 435         struct clk_hw hw;
 436         bool hw_ctrld;
 437         bool reset;
 438         void __iomem *res_reg;
 439         u8 res_bit;
 440         void __iomem *en_reg;
 441         u8 en_bit;
 442         u16 clk_val;
 443 };
 444
 445 #define to_syscon(_hw) container_of(_hw, struct clk_syscon, hw)
 446
 447 static DEFINE_SPINLOCK(syscon_resetreg_lock);
 448
 449 /*
 450  * Reset control functions. We remember if a block has been
 451  * taken out of reset and don't remove the reset assertion again
 452  * and vice versa. Currently we only remove resets so the
 453  * enablement function is defined out.
 454  */
 455 static void syscon_block_reset_enable(struct clk_syscon *sclk)
 456 {
 457         unsigned long iflags;
 458         u16 val;
 459
 460         /* Not all blocks support resetting */
 461         if (!sclk->res_reg)
 462                 return;
 463         spin_lock_irqsave(&syscon_resetreg_lock, iflags);
 464         val = readw(sclk->res_reg);
 465         val |= BIT(sclk->res_bit);
 466         writew(val, sclk->res_reg);
 467         spin_unlock_irqrestore(&syscon_resetreg_lock, iflags);
 468         sclk->reset = true;
 469 }
 470
 471 static void syscon_block_reset_disable(struct clk_syscon *sclk)
 472 {
 473         unsigned long iflags;
 474         u16 val;
 475
 476         /* Not all blocks support resetting */
 477         if (!sclk->res_reg)
 478                 return;
 479         spin_lock_irqsave(&syscon_resetreg_lock, iflags);
 480         val = readw(sclk->res_reg);
 481         val &= ~BIT(sclk->res_bit);
 482         writew(val, sclk->res_reg);
 483         spin_unlock_irqrestore(&syscon_resetreg_lock, iflags);
 484         sclk->reset = false;
 485 }
 486
 487 static int syscon_clk_prepare(struct clk_hw *hw)
 488 {
 489         struct clk_syscon *sclk = to_syscon(hw);
 490
 491         /* If the block is in reset, bring it out */
 492         if (sclk->reset)
 493                 syscon_block_reset_disable(sclk);
 494         return 0;
 495 }
 496
 497 static void syscon_clk_unprepare(struct clk_hw *hw)
 498 {
 499         struct clk_syscon *sclk = to_syscon(hw);
 500
 501         /* Please don't force the console into reset */
 502         if (sclk->clk_val == U300_SYSCON_SBCER_UART_CLK_EN)
 503                 return;
 504         /* When unpreparing, force block into reset */
 505         if (!sclk->reset)
 506                 syscon_block_reset_enable(sclk);
 507 }
 508
 509 static int syscon_clk_enable(struct clk_hw *hw)
 510 {
 511         struct clk_syscon *sclk = to_syscon(hw);
 512
 513         /* Don't touch the hardware controlled clocks */
 514         if (sclk->hw_ctrld)
 515                 return 0;
 516         /* These cannot be controlled */
 517         if (sclk->clk_val == 0xFFFFU)
 518                 return 0;
 519
 520         writew(sclk->clk_val, syscon_vbase + U300_SYSCON_SBCER);
 521         return 0;
 522 }
 523
 524 static void syscon_clk_disable(struct clk_hw *hw)
 525 {
 526         struct clk_syscon *sclk = to_syscon(hw);
 527
 528         /* Don't touch the hardware controlled clocks */
 529         if (sclk->hw_ctrld)
 530                 return;
 531         if (sclk->clk_val == 0xFFFFU)
 532                 return;
 533         /* Please don't disable the console port */
 534         if (sclk->clk_val == U300_SYSCON_SBCER_UART_CLK_EN)
 535                 return;
 536
 537         writew(sclk->clk_val, syscon_vbase + U300_SYSCON_SBCDR);
 538 }
 539
 540 static int syscon_clk_is_enabled(struct clk_hw *hw)
 541 {
 542         struct clk_syscon *sclk = to_syscon(hw);
 543         u16 val;
 544
 545         /* If no enable register defined, it's always-on */
 546         if (!sclk->en_reg)
 547                 return 1;
 548
 549         val = readw(sclk->en_reg);
 550         val &= BIT(sclk->en_bit);
 551
 552         return val ? 1 : 0;
 553 }
 554
 555 static u16 syscon_get_perf(void)
 556 {
 557         u16 val;
 558
 559         val = readw(syscon_vbase + U300_SYSCON_CCR);
 560         val &= U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK;
 561         return val;
 562 }
 563
 564 static unsigned long
 565 syscon_clk_recalc_rate(struct clk_hw *hw,
 566                        unsigned long parent_rate)
 567 {
 568         struct clk_syscon *sclk = to_syscon(hw);
 569         u16 perf = syscon_get_perf();
 570
 571         switch(sclk->clk_val) {
 572         case U300_SYSCON_SBCER_FAST_BRIDGE_CLK_EN:
 573         case U300_SYSCON_SBCER_I2C0_CLK_EN:
 574         case U300_SYSCON_SBCER_I2C1_CLK_EN:
 575         case U300_SYSCON_SBCER_MMC_CLK_EN:
 576         case U300_SYSCON_SBCER_SPI_CLK_EN:
 577                 /* The FAST clocks have one progression */
 578                 switch(perf) {
 579                 case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER:
 580                 case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW:
 581                         return 13000000;
 582                 default:
 583                         return parent_rate; /* 26 MHz */
 584                 }
 585         case U300_SYSCON_SBCER_DMAC_CLK_EN:
 586         case U300_SYSCON_SBCER_NANDIF_CLK_EN:
 587         case U300_SYSCON_SBCER_XGAM_CLK_EN:
 588                 /* AMBA interconnect peripherals */
 589                 switch(perf) {
 590                 case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER:
 591                 case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW:
 592                         return 6500000;
 593                 case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE:
 594                         return 26000000;
 595                 default:
 596                         return parent_rate; /* 52 MHz */
 597                 }
 598         case U300_SYSCON_SBCER_SEMI_CLK_EN:
 599         case U300_SYSCON_SBCER_EMIF_CLK_EN:
 600                 /* EMIF speeds */
 601                 switch(perf) {
 602                 case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER:
 603                 case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW:
 604                         return 13000000;
 605                 case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE:
 606                         return 52000000;
 607                 default:
 608                         return 104000000;
 609                 }
 610         case U300_SYSCON_SBCER_CPU_CLK_EN:
 611                 /* And the fast CPU clock */
 612                 switch(perf) {
 613                 case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER:
 614                 case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW:
 615                         return 13000000;
 616                 case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE:
 617                         return 52000000;
 618                 case U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH:
 619                         return 104000000;
 620                 default:
 621                         return parent_rate; /* 208 MHz */
 622                 }
 623         default:
 624                 /*
 625                  * The SLOW clocks and default just inherit the rate of
 626                  * their parent (typically PLL13 13 MHz).
 627                  */
 628                 return parent_rate;
 629         }
 630 }
 631
 632 static long
 633 syscon_clk_round_rate(struct clk_hw *hw, unsigned long rate,
 634                       unsigned long *prate)
 635 {
 636         struct clk_syscon *sclk = to_syscon(hw);
 637
 638         if (sclk->clk_val != U300_SYSCON_SBCER_CPU_CLK_EN)
 639                 return *prate;
 640         /* We really only support setting the rate of the CPU clock */
 641         if (rate <= 13000000)
 642                 return 13000000;
 643         if (rate <= 52000000)
 644                 return 52000000;
 645         if (rate <= 104000000)
 646                 return 104000000;
 647         return 208000000;
 648 }
 649
 650 static int syscon_clk_set_rate(struct clk_hw *hw, unsigned long rate,
 651                                unsigned long parent_rate)
 652 {
 653         struct clk_syscon *sclk = to_syscon(hw);
 654         u16 val;
 655
 656         /* We only support setting the rate of the CPU clock */
 657         if (sclk->clk_val != U300_SYSCON_SBCER_CPU_CLK_EN)
 658                 return -EINVAL;
 659         switch (rate) {
 660         case 13000000:
 661                 val = U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER;
 662                 break;
 663         case 52000000:
 664                 val = U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE;
 665                 break;
 666         case 104000000:
 667                 val = U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH;
 668                 break;
 669         case 208000000:
 670                 val = U300_SYSCON_CCR_CLKING_PERFORMANCE_BEST;
 671                 break;
 672         default:
 673                 return -EINVAL;
 674         }
 675         val |= readw(syscon_vbase + U300_SYSCON_CCR) &
 676                 ~U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK ;
 677         writew(val, syscon_vbase + U300_SYSCON_CCR);
 678         return 0;
 679 }
 680
 681 static const struct clk_ops syscon_clk_ops = {
 682         .prepare = syscon_clk_prepare,
 683         .unprepare = syscon_clk_unprepare,
 684         .enable = syscon_clk_enable,
 685         .disable = syscon_clk_disable,
 686         .is_enabled = syscon_clk_is_enabled,
 687         .recalc_rate = syscon_clk_recalc_rate,
 688         .round_rate = syscon_clk_round_rate,
 689         .set_rate = syscon_clk_set_rate,
 690 };
 691
 692 static struct clk * __init
 693 syscon_clk_register(struct device *dev, const char *name,
 694                     const char *parent_name, unsigned long flags,
 695                     bool hw_ctrld,
 696                     void __iomem *res_reg, u8 res_bit,
 697                     void __iomem *en_reg, u8 en_bit,
 698                     u16 clk_val)
 699 {
 700         struct clk *clk;
 701         struct clk_syscon *sclk;
 702         struct clk_init_data init;
 703
 704         sclk = kzalloc(sizeof(struct clk_syscon), GFP_KERNEL);
 705         if (!sclk) {
 706                 pr_err("could not allocate syscon clock %s\n",
 707                         name);
 708                 return ERR_PTR(-ENOMEM);
 709         }
 710         init.name = name;
 711         init.ops = &syscon_clk_ops;
 712         init.flags = flags;
 713         init.parent_names = (parent_name ? &parent_name : NULL);
 714         init.num_parents = (parent_name ? 1 : 0);
 715         sclk->hw.init = &init;
 716         sclk->hw_ctrld = hw_ctrld;
 717         /* Assume the block is in reset at registration */
 718         sclk->reset = true;
 719         sclk->res_reg = res_reg;
 720         sclk->res_bit = res_bit;
 721         sclk->en_reg = en_reg;
 722         sclk->en_bit = en_bit;
 723         sclk->clk_val = clk_val;
 724
 725         clk = clk_register(dev, &sclk->hw);
 726         if (IS_ERR(clk))
 727                 kfree(sclk);
 728
 729         return clk;
 730 }
 731
 732 #define U300_CLK_TYPE_SLOW 0
 733 #define U300_CLK_TYPE_FAST 1
 734 #define U300_CLK_TYPE_REST 2
 735
 736 /**
 737  * struct u300_clock - defines the bits and pieces for a certain clock
 738  * @type: the clock type, slow fast or rest
 739  * @id: the bit in the slow/fast/rest register for this clock
 740  * @hw_ctrld: whether the clock is hardware controlled
 741  * @clk_val: a value to poke in the one-write enable/disable registers
 742  */
 743 struct u300_clock {
 744         u8 type;
 745         u8 id;
 746         bool hw_ctrld;
 747         u16 clk_val;
 748 };
 749
 750 static struct u300_clock const u300_clk_lookup[] __initconst = {
 751         {
 752                 .type = U300_CLK_TYPE_REST,
 753                 .id = 3,
 754                 .hw_ctrld = true,
 755                 .clk_val = U300_SYSCON_SBCER_CPU_CLK_EN,
 756         },
 757         {
 758                 .type = U300_CLK_TYPE_REST,
 759                 .id = 4,
 760                 .hw_ctrld = true,
 761                 .clk_val = U300_SYSCON_SBCER_DMAC_CLK_EN,
 762         },
 763         {
 764                 .type = U300_CLK_TYPE_REST,
 765                 .id = 5,
 766                 .hw_ctrld = false,
 767                 .clk_val = U300_SYSCON_SBCER_EMIF_CLK_EN,
 768         },
 769         {
 770                 .type = U300_CLK_TYPE_REST,
 771                 .id = 6,
 772                 .hw_ctrld = false,
 773                 .clk_val = U300_SYSCON_SBCER_NANDIF_CLK_EN,
 774         },
 775         {
 776                 .type = U300_CLK_TYPE_REST,
 777                 .id = 8,
 778                 .hw_ctrld = true,
 779                 .clk_val = U300_SYSCON_SBCER_XGAM_CLK_EN,
 780         },
 781         {
 782                 .type = U300_CLK_TYPE_REST,
 783                 .id = 9,
 784                 .hw_ctrld = false,
 785                 .clk_val = U300_SYSCON_SBCER_SEMI_CLK_EN,
 786         },
 787         {
 788                 .type = U300_CLK_TYPE_REST,
 789                 .id = 10,
 790                 .hw_ctrld = true,
 791                 .clk_val = U300_SYSCON_SBCER_AHB_SUBSYS_BRIDGE_CLK_EN,
 792         },
 793         {
 794                 .type = U300_CLK_TYPE_REST,
 795                 .id = 12,
 796                 .hw_ctrld = false,
 797                 /* INTCON: cannot be enabled, just taken out of reset */
 798                 .clk_val = 0xFFFFU,
 799         },
 800         {
 801                 .type = U300_CLK_TYPE_FAST,
 802                 .id = 0,
 803                 .hw_ctrld = true,
 804                 .clk_val = U300_SYSCON_SBCER_FAST_BRIDGE_CLK_EN,
 805         },
 806         {
 807                 .type = U300_CLK_TYPE_FAST,
 808                 .id = 1,
 809                 .hw_ctrld = false,
 810                 .clk_val = U300_SYSCON_SBCER_I2C0_CLK_EN,
 811         },
 812         {
 813                 .type = U300_CLK_TYPE_FAST,
 814                 .id = 2,
 815                 .hw_ctrld = false,
 816                 .clk_val = U300_SYSCON_SBCER_I2C1_CLK_EN,
 817         },
 818         {
 819                 .type = U300_CLK_TYPE_FAST,
 820                 .id = 5,
 821                 .hw_ctrld = false,
 822                 .clk_val = U300_SYSCON_SBCER_MMC_CLK_EN,
 823         },
 824         {
 825                 .type = U300_CLK_TYPE_FAST,
 826                 .id = 6,
 827                 .hw_ctrld = false,
 828                 .clk_val = U300_SYSCON_SBCER_SPI_CLK_EN,
 829         },
 830         {
 831                 .type = U300_CLK_TYPE_SLOW,
 832                 .id = 0,
 833                 .hw_ctrld = true,
 834                 .clk_val = U300_SYSCON_SBCER_SLOW_BRIDGE_CLK_EN,
 835         },
 836         {
 837                 .type = U300_CLK_TYPE_SLOW,
 838                 .id = 1,
 839                 .hw_ctrld = false,
 840                 .clk_val = U300_SYSCON_SBCER_UART_CLK_EN,
 841         },
 842         {
 843                 .type = U300_CLK_TYPE_SLOW,
 844                 .id = 4,
 845                 .hw_ctrld = false,
 846                 .clk_val = U300_SYSCON_SBCER_GPIO_CLK_EN,
 847         },
 848         {
 849                 .type = U300_CLK_TYPE_SLOW,
 850                 .id = 6,
 851                 .hw_ctrld = true,
 852                 /* No clock enable register bit */
 853                 .clk_val = 0xFFFFU,
 854         },
 855         {
 856                 .type = U300_CLK_TYPE_SLOW,
 857                 .id = 7,
 858                 .hw_ctrld = false,
 859                 .clk_val = U300_SYSCON_SBCER_APP_TMR_CLK_EN,
 860         },
 861         {
 862                 .type = U300_CLK_TYPE_SLOW,
 863                 .id = 8,
 864                 .hw_ctrld = false,
 865                 .clk_val = U300_SYSCON_SBCER_ACC_TMR_CLK_EN,
 866         },
 867 };
 868
 869 static void __init of_u300_syscon_clk_init(struct device_node *np)
 870 {
 871         struct clk *clk = ERR_PTR(-EINVAL);
 872         const char *clk_name = np->name;
 873         const char *parent_name;
 874         void __iomem *res_reg;
 875         void __iomem *en_reg;
 876         u32 clk_type;
 877         u32 clk_id;
 878         int i;
 879
 880         if (of_property_read_u32(np, "clock-type", &clk_type)) {
 881                 pr_err("%s: syscon clock \"%s\" missing clock-type property\n",
 882                        __func__, clk_name);
 883                 return;
 884         }
 885         if (of_property_read_u32(np, "clock-id", &clk_id)) {
 886                 pr_err("%s: syscon clock \"%s\" missing clock-id property\n",
 887                        __func__, clk_name);
 888                 return;
 889         }
 890         parent_name = of_clk_get_parent_name(np, 0);
 891
 892         switch (clk_type) {
 893         case U300_CLK_TYPE_SLOW:
 894                 res_reg = syscon_vbase + U300_SYSCON_RSR;
 895                 en_reg = syscon_vbase + U300_SYSCON_CESR;
 896                 break;
 897         case U300_CLK_TYPE_FAST:
 898                 res_reg = syscon_vbase + U300_SYSCON_RFR;
 899                 en_reg = syscon_vbase + U300_SYSCON_CEFR;
 900                 break;
 901         case U300_CLK_TYPE_REST:
 902                 res_reg = syscon_vbase + U300_SYSCON_RRR;
 903                 en_reg = syscon_vbase + U300_SYSCON_CERR;
 904                 break;
 905         default:
 906                 pr_err("unknown clock type %x specified\n", clk_type);
 907                 return;
 908         }
 909
 910         for (i = 0; i < ARRAY_SIZE(u300_clk_lookup); i++) {
 911                 const struct u300_clock *u3clk = &u300_clk_lookup[i];
 912
 913                 if (u3clk->type == clk_type && u3clk->id == clk_id)
 914                         clk = syscon_clk_register(NULL,
 915                                                   clk_name, parent_name,
 916                                                   0, u3clk->hw_ctrld,
 917                                                   res_reg, u3clk->id,
 918                                                   en_reg, u3clk->id,
 919                                                   u3clk->clk_val);
 920         }
 921
 922         if (!IS_ERR(clk)) {
 923                 of_clk_add_provider(np, of_clk_src_simple_get, clk);
 924
 925                 /*
 926                  * Some few system clocks - device tree does not
 927                  * represent clocks without a corresponding device node.
 928                  * for now we add these three clocks here.
 929                  */
 930                 if (clk_type == U300_CLK_TYPE_REST && clk_id == 5)
 931                         clk_register_clkdev(clk, NULL, "pl172");
 932                 if (clk_type == U300_CLK_TYPE_REST && clk_id == 9)
 933                         clk_register_clkdev(clk, NULL, "semi");
 934                 if (clk_type == U300_CLK_TYPE_REST && clk_id == 12)
 935                         clk_register_clkdev(clk, NULL, "intcon");
 936         }
 937 }
 938
 939 /**
 940  * struct clk_mclk - U300 MCLK clock (MMC/SD clock)
 941  * @hw: corresponding clock hardware entry
 942  * @is_mspro: if this is the memory stick clock rather than MMC/SD
 943  */
 944 struct clk_mclk {
 945         struct clk_hw hw;
 946         bool is_mspro;
 947 };
 948
 949 #define to_mclk(_hw) container_of(_hw, struct clk_mclk, hw)
 950
 951 static int mclk_clk_prepare(struct clk_hw *hw)
 952 {
 953         struct clk_mclk *mclk = to_mclk(hw);
 954         u16 val;
 955
 956         /* The MMC and MSPRO clocks need some special set-up */
 957         if (!mclk->is_mspro) {
 958                 /* Set default MMC clock divisor to 18.9 MHz */
 959                 writew(0x0054U, syscon_vbase + U300_SYSCON_MMF0R);
 960                 val = readw(syscon_vbase + U300_SYSCON_MMCR);
 961                 /* Disable the MMC feedback clock */
 962                 val &= ~U300_SYSCON_MMCR_MMC_FB_CLK_SEL_ENABLE;
 963                 /* Disable MSPRO frequency */
 964                 val &= ~U300_SYSCON_MMCR_MSPRO_FREQSEL_ENABLE;
 965                 writew(val, syscon_vbase + U300_SYSCON_MMCR);
 966         } else {
 967                 val = readw(syscon_vbase + U300_SYSCON_MMCR);
 968                 /* Disable the MMC feedback clock */
 969                 val &= ~U300_SYSCON_MMCR_MMC_FB_CLK_SEL_ENABLE;
 970                 /* Enable MSPRO frequency */
 971                 val |= U300_SYSCON_MMCR_MSPRO_FREQSEL_ENABLE;
 972                 writew(val, syscon_vbase + U300_SYSCON_MMCR);
 973         }
 974
 975         return 0;
 976 }
 977
 978 static unsigned long
 979 mclk_clk_recalc_rate(struct clk_hw *hw,
 980                      unsigned long parent_rate)
 981 {
 982         u16 perf = syscon_get_perf();
 983
 984         switch (perf) {
 985         case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW_POWER:
 986                 /*
 987                  * Here, the 208 MHz PLL gets shut down and the always
 988                  * on 13 MHz PLL used for RTC etc kicks into use
 989                  * instead.
 990                  */
 991                 return 13000000;
 992         case U300_SYSCON_CCR_CLKING_PERFORMANCE_LOW:
 993         case U300_SYSCON_CCR_CLKING_PERFORMANCE_INTERMEDIATE:
 994         case U300_SYSCON_CCR_CLKING_PERFORMANCE_HIGH:
 995         case U300_SYSCON_CCR_CLKING_PERFORMANCE_BEST:
 996         {
 997                 /*
 998                  * This clock is under program control. The register is
 999                  * divided in two nybbles, bit 7-4 gives cycles-1 to count
1000                  * high, bit 3-0 gives cycles-1 to count low. Distribute
1001                  * these with no more than 1 cycle difference between
1002                  * low and high and add low and high to get the actual
1003                  * divisor. The base PLL is 208 MHz. Writing 0x00 will
1004                  * divide by 1 and 1 so the highest frequency possible
1005                  * is 104 MHz.
1006                  *
1007                  * e.g. 0x54 =>
1008                  * f = 208 / ((5+1) + (4+1)) = 208 / 11 = 18.9 MHz
1009                  */
1010                 u16 val = readw(syscon_vbase + U300_SYSCON_MMF0R) &
1011                         U300_SYSCON_MMF0R_MASK;
1012                 switch (val) {
1013                 case 0x0054:
1014                         return 18900000;
1015                 case 0x0044:
1016                         return 20800000;
1017                 case 0x0043:
1018                         return 23100000;
1019                 case 0x0033:
1020                         return 26000000;
1021                 case 0x0032:
1022                         return 29700000;
1023                 case 0x0022:
1024                         return 34700000;
1025                 case 0x0021:
1026                         return 41600000;
1027                 case 0x0011:
1028                         return 52000000;
1029                 case 0x0000:
1030                         return 104000000;
1031                 default:
1032                         break;
1033                 }
1034         }
1035         default:
1036                 break;
1037         }
1038         return parent_rate;
1039 }
1040
1041 static long
1042 mclk_clk_round_rate(struct clk_hw *hw, unsigned long rate,
1043                     unsigned long *prate)
1044 {
1045         if (rate <= 18900000)
1046                 return 18900000;
1047         if (rate <= 20800000)
1048                 return 20800000;
1049         if (rate <= 23100000)
1050                 return 23100000;
1051         if (rate <= 26000000)
1052                 return 26000000;
1053         if (rate <= 29700000)
1054                 return 29700000;
1055         if (rate <= 34700000)
1056                 return 34700000;
1057         if (rate <= 41600000)
1058                 return 41600000;
1059         /* Highest rate */
1060         return 52000000;
1061 }
1062
1063 static int mclk_clk_set_rate(struct clk_hw *hw, unsigned long rate,
1064                              unsigned long parent_rate)
1065 {
1066         u16 val;
1067         u16 reg;
1068
1069         switch (rate) {
1070         case 18900000:
1071                 val = 0x0054;
1072                 break;
1073         case 20800000:
1074                 val = 0x0044;
1075                 break;
1076         case 23100000:
1077                 val = 0x0043;
1078                 break;
1079         case 26000000:
1080                 val = 0x0033;
1081                 break;
1082         case 29700000:
1083                 val = 0x0032;
1084                 break;
1085         case 34700000:
1086                 val = 0x0022;
1087                 break;
1088         case 41600000:
1089                 val = 0x0021;
1090                 break;
1091         case 52000000:
1092                 val = 0x0011;
1093                 break;
1094         case 104000000:
1095                 val = 0x0000;
1096                 break;
1097         default:
1098                 return -EINVAL;
1099         }
1100
1101         reg = readw(syscon_vbase + U300_SYSCON_MMF0R) &
1102                 ~U300_SYSCON_MMF0R_MASK;
1103         writew(reg | val, syscon_vbase + U300_SYSCON_MMF0R);
1104         return 0;
1105 }
1106
1107 static const struct clk_ops mclk_ops = {
1108         .prepare = mclk_clk_prepare,
1109         .recalc_rate = mclk_clk_recalc_rate,
1110         .round_rate = mclk_clk_round_rate,
1111         .set_rate = mclk_clk_set_rate,
1112 };
1113
1114 static struct clk * __init
1115 mclk_clk_register(struct device *dev, const char *name,
1116                   const char *parent_name, bool is_mspro)
1117 {
1118         struct clk *clk;
1119         struct clk_mclk *mclk;
1120         struct clk_init_data init;
1121
1122         mclk = kzalloc(sizeof(struct clk_mclk), GFP_KERNEL);
1123         if (!mclk) {
1124                 pr_err("could not allocate MMC/SD clock %s\n",
1125                        name);
1126                 return ERR_PTR(-ENOMEM);
1127         }
1128         init.name = "mclk";
1129         init.ops = &mclk_ops;
1130         init.flags = 0;
1131         init.parent_names = (parent_name ? &parent_name : NULL);
1132         init.num_parents = (parent_name ? 1 : 0);
1133         mclk->hw.init = &init;
1134         mclk->is_mspro = is_mspro;
1135
1136         clk = clk_register(dev, &mclk->hw);
1137         if (IS_ERR(clk))
1138                 kfree(mclk);
1139
1140         return clk;
1141 }
1142
1143 static void __init of_u300_syscon_mclk_init(struct device_node *np)
1144 {
1145         struct clk *clk = ERR_PTR(-EINVAL);
1146         const char *clk_name = np->name;
1147         const char *parent_name;
1148
1149         parent_name = of_clk_get_parent_name(np, 0);
1150         clk = mclk_clk_register(NULL, clk_name, parent_name, false);
1151         if (!IS_ERR(clk))
1152                 of_clk_add_provider(np, of_clk_src_simple_get, clk);
1153 }
1154
1155 static const struct of_device_id u300_clk_match[] __initconst = {
1156         {
1157                 .compatible = "fixed-clock",
1158                 .data = of_fixed_clk_setup,
1159         },
1160         {
1161                 .compatible = "fixed-factor-clock",
1162                 .data = of_fixed_factor_clk_setup,
1163         },
1164         {
1165                 .compatible = "stericsson,u300-syscon-clk",
1166                 .data = of_u300_syscon_clk_init,
1167         },
1168         {
1169                 .compatible = "stericsson,u300-syscon-mclk",
1170                 .data = of_u300_syscon_mclk_init,
1171         },
1172         {}
1173 };
1174
1175
1176 void __init u300_clk_init(void __iomem *base)
1177 {
1178         u16 val;
1179
1180         syscon_vbase = base;
1181
1182         /* Set system to run at PLL208, max performance, a known state. */
1183         val = readw(syscon_vbase + U300_SYSCON_CCR);
1184         val &= ~U300_SYSCON_CCR_CLKING_PERFORMANCE_MASK;
1185         writew(val, syscon_vbase + U300_SYSCON_CCR);
1186         /* Wait for the PLL208 to lock if not locked in yet */
1187         while (!(readw(syscon_vbase + U300_SYSCON_CSR) &
1188                  U300_SYSCON_CSR_PLL208_LOCK_IND));
1189
1190         /* Power management enable */
1191         val = readw(syscon_vbase + U300_SYSCON_PMCR);
1192         val |= U300_SYSCON_PMCR_PWR_MGNT_ENABLE;
1193         writew(val, syscon_vbase + U300_SYSCON_PMCR);
1194
1195         of_clk_init(u300_clk_match);
1196 }