1 // SPDX-License-Identifier: GPL-2.0+
3 * comedi/drivers/amplc_dio200.c
5 * Driver for Amplicon PC212E, PC214E, PC215E, PC218E, PC272E.
7 * Copyright (C) 2005-2013 MEV Ltd. <https://www.mev.co.uk/>
9 * COMEDI - Linux Control and Measurement Device Interface
10 * Copyright (C) 1998,2000 David A. Schleef <ds@schleef.org>
14 * Driver: amplc_dio200
15 * Description: Amplicon 200 Series ISA Digital I/O
16 * Author: Ian Abbott <abbotti@mev.co.uk>
17 * Devices: [Amplicon] PC212E (pc212e), PC214E (pc214e), PC215E (pc215e),
18 * PC218E (pc218e), PC272E (pc272e)
19 * Updated: Mon, 18 Mar 2013 14:40:41 +0000
23 * Configuration options:
24 * [0] - I/O port base address
25 * [1] - IRQ (optional, but commands won't work without it)
27 * Passing a zero for an option is the same as leaving it unspecified.
31 * PC212E PC214E PC215E
32 * ------------- ------------- -------------
35 * 1 CTR-Y1 PPI-Y PPI-Y
36 * 2 CTR-Y2 CTR-Z1* CTR-Z1
37 * 3 CTR-Z1 INTERRUPT* CTR-Z2
42 * ------------- -------------
52 * Each PPI is a 8255 chip providing 24 DIO channels. The DIO channels
53 * are configurable as inputs or outputs in four groups:
55 * Port A - channels 0 to 7
56 * Port B - channels 8 to 15
57 * Port CL - channels 16 to 19
58 * Port CH - channels 20 to 23
60 * Only mode 0 of the 8255 chips is supported.
62 * Each CTR is a 8254 chip providing 3 16-bit counter channels. Each
63 * channel is configured individually with INSN_CONFIG instructions. The
64 * specific type of configuration instruction is specified in data[0].
65 * Some configuration instructions expect an additional parameter in
66 * data[1]; others return a value in data[1]. The following configuration
67 * instructions are supported:
69 * INSN_CONFIG_SET_COUNTER_MODE. Sets the counter channel's mode and
70 * BCD/binary setting specified in data[1].
72 * INSN_CONFIG_8254_READ_STATUS. Reads the status register value for the
73 * counter channel into data[1].
75 * INSN_CONFIG_SET_CLOCK_SRC. Sets the counter channel's clock source as
76 * specified in data[1] (this is a hardware-specific value). Not
77 * supported on PC214E. For the other boards, valid clock sources are
80 * 0. CLK n, the counter channel's dedicated CLK input from the SK1
81 * connector. (N.B. for other values, the counter channel's CLKn
82 * pin on the SK1 connector is an output!)
83 * 1. Internal 10 MHz clock.
84 * 2. Internal 1 MHz clock.
85 * 3. Internal 100 kHz clock.
86 * 4. Internal 10 kHz clock.
87 * 5. Internal 1 kHz clock.
88 * 6. OUT n-1, the output of counter channel n-1 (see note 1 below).
89 * 7. Ext Clock, the counter chip's dedicated Ext Clock input from
90 * the SK1 connector. This pin is shared by all three counter
91 * channels on the chip.
93 * INSN_CONFIG_GET_CLOCK_SRC. Returns the counter channel's current
94 * clock source in data[1]. For internal clock sources, data[2] is set
95 * to the period in ns.
97 * INSN_CONFIG_SET_GATE_SRC. Sets the counter channel's gate source as
98 * specified in data[2] (this is a hardware-specific value). Not
99 * supported on PC214E. For the other boards, valid gate sources are 0
102 * 0. VCC (internal +5V d.c.), i.e. gate permanently enabled.
103 * 1. GND (internal 0V d.c.), i.e. gate permanently disabled.
104 * 2. GAT n, the counter channel's dedicated GAT input from the SK1
105 * connector. (N.B. for other values, the counter channel's GATn
106 * pin on the SK1 connector is an output!)
107 * 3. /OUT n-2, the inverted output of counter channel n-2 (see note
114 * INSN_CONFIG_GET_GATE_SRC. Returns the counter channel's current gate
117 * Clock and gate interconnection notes:
119 * 1. Clock source OUT n-1 is the output of the preceding channel on the
120 * same counter subdevice if n > 0, or the output of channel 2 on the
121 * preceding counter subdevice (see note 3) if n = 0.
123 * 2. Gate source /OUT n-2 is the inverted output of channel 0 on the
124 * same counter subdevice if n = 2, or the inverted output of channel n+1
125 * on the preceding counter subdevice (see note 3) if n < 2.
127 * 3. The counter subdevices are connected in a ring, so the highest
128 * counter subdevice precedes the lowest.
130 * The 'INTERRUPT' subdevice pretends to be a digital input subdevice. The
131 * digital inputs come from the interrupt status register. The number of
132 * channels matches the number of interrupt sources. The PC214E does not
133 * have an interrupt status register; see notes on 'INTERRUPT SOURCES'
138 * PC212E PC214E PC215E
139 * ------------- ------------- -------------
141 * 0 PPI-X-C0 JUMPER-J5 PPI-X-C0
142 * 1 PPI-X-C3 PPI-X-C3
143 * 2 CTR-Y1-OUT1 PPI-Y-C0
144 * 3 CTR-Y2-OUT1 PPI-Y-C3
145 * 4 CTR-Z1-OUT1 CTR-Z1-OUT1
146 * 5 CTR-Z2-OUT1 CTR-Z2-OUT1
149 * ------------- -------------
151 * 0 CTR-X1-OUT1 PPI-X-C0
152 * 1 CTR-X2-OUT1 PPI-X-C3
153 * 2 CTR-Y1-OUT1 PPI-Y-C0
154 * 3 CTR-Y2-OUT1 PPI-Y-C3
155 * 4 CTR-Z1-OUT1 PPI-Z-C0
156 * 5 CTR-Z2-OUT1 PPI-Z-C3
158 * When an interrupt source is enabled in the interrupt source enable
159 * register, a rising edge on the source signal latches the corresponding
160 * bit to 1 in the interrupt status register.
162 * When the interrupt status register value as a whole (actually, just the
163 * 6 least significant bits) goes from zero to non-zero, the board will
164 * generate an interrupt. No further interrupts will occur until the
165 * interrupt status register is cleared to zero. To clear a bit to zero in
166 * the interrupt status register, the corresponding interrupt source must
167 * be disabled in the interrupt source enable register (there is no
168 * separate interrupt clear register).
170 * The PC214E does not have an interrupt source enable register or an
171 * interrupt status register; its 'INTERRUPT' subdevice has a single
172 * channel and its interrupt source is selected by the position of jumper
177 * The driver supports a read streaming acquisition command on the
178 * 'INTERRUPT' subdevice. The channel list selects the interrupt sources
179 * to be enabled. All channels will be sampled together (convert_src ==
180 * TRIG_NOW). The scan begins a short time after the hardware interrupt
181 * occurs, subject to interrupt latencies (scan_begin_src == TRIG_EXT,
182 * scan_begin_arg == 0). The value read from the interrupt status register
183 * is packed into a short value, one bit per requested channel, in the
184 * order they appear in the channel list.
187 #include <linux/module.h>
188 #include <linux/comedi/comedidev.h>
190 #include "amplc_dio200.h"
193 * Board descriptions.
195 static const struct dio200_board dio200_isa_boards[] = {
200 sd_8255, sd_8254, sd_8254, sd_8254, sd_8254, sd_intr
202 .sdinfo = { 0x00, 0x08, 0x0c, 0x10, 0x14, 0x3f },
204 .has_clk_gat_sce = true,
209 sd_8255, sd_8255, sd_8254, sd_intr
211 .sdinfo = { 0x00, 0x08, 0x10, 0x01 },
216 sd_8255, sd_8255, sd_8254, sd_8254, sd_intr
218 .sdinfo = { 0x00, 0x08, 0x10, 0x14, 0x3f },
220 .has_clk_gat_sce = true,
225 sd_8254, sd_8254, sd_8255, sd_8254, sd_8254, sd_intr
227 .sdinfo = { 0x00, 0x04, 0x08, 0x0c, 0x10, 0x14, 0x3f },
229 .has_clk_gat_sce = true,
234 sd_8255, sd_8255, sd_8255, sd_intr
236 .sdinfo = { 0x00, 0x08, 0x10, 0x3f },
241 static int dio200_attach(struct comedi_device *dev, struct comedi_devconfig *it)
245 ret = comedi_request_region(dev, it->options[0], 0x20);
249 return amplc_dio200_common_attach(dev, it->options[1], 0);
252 static struct comedi_driver amplc_dio200_driver = {
253 .driver_name = "amplc_dio200",
254 .module = THIS_MODULE,
255 .attach = dio200_attach,
256 .detach = comedi_legacy_detach,
257 .board_name = &dio200_isa_boards[0].name,
258 .offset = sizeof(struct dio200_board),
259 .num_names = ARRAY_SIZE(dio200_isa_boards),
261 module_comedi_driver(amplc_dio200_driver);
263 MODULE_AUTHOR("Comedi https://www.comedi.org");
264 MODULE_DESCRIPTION("Comedi driver for Amplicon 200 Series ISA DIO boards");
265 MODULE_LICENSE("GPL");