arch/mips/boot/dts/qca/ar9331.dtsi

   1 // SPDX-License-Identifier: GPL-2.0
   2 #include <dt-bindings/clock/ath79-clk.h>
   3
   4 / {
   5         compatible = "qca,ar9331";
   6
   7         #address-cells = <1>;
   8         #size-cells = <1>;
   9
  10         cpus {
  11                 #address-cells = <1>;
  12                 #size-cells = <0>;
  13
  14                 cpu@0 {
  15                         device_type = "cpu";
  16                         compatible = "mips,mips24Kc";
  17                         clocks = <&pll ATH79_CLK_CPU>;
  18                         reg = <0>;
  19                 };
  20         };
  21
  22         cpuintc: interrupt-controller {
  23                 compatible = "qca,ar7100-cpu-intc";
  24
  25                 interrupt-controller;
  26                 #interrupt-cells = <1>;
  27
  28                 qca,ddr-wb-channel-interrupts = <2>, <3>;
  29                 qca,ddr-wb-channels = <&ddr_ctrl 3>, <&ddr_ctrl 2>;
  30         };
  31
  32         ref: ref {
  33                 compatible = "fixed-clock";
  34                 #clock-cells = <0>;
  35         };
  36
  37         ahb {
  38                 compatible = "simple-bus";
  39                 ranges;
  40
  41                 #address-cells = <1>;
  42                 #size-cells = <1>;
  43
  44                 interrupt-parent = <&cpuintc>;
  45
  46                 apb {
  47                         compatible = "simple-bus";
  48                         ranges;
  49
  50                         #address-cells = <1>;
  51                         #size-cells = <1>;
  52
  53                         interrupt-parent = <&miscintc>;
  54
  55                         ddr_ctrl: memory-controller@18000000 {
  56                                 compatible = "qca,ar7240-ddr-controller";
  57                                 reg = <0x18000000 0x100>;
  58
  59                                 #qca,ddr-wb-channel-cells = <1>;
  60                         };
  61
  62                         uart: serial@18020000 {
  63                                 compatible = "qca,ar9330-uart";
  64                                 reg = <0x18020000 0x14>;
  65
  66                                 interrupts = <3>;
  67
  68                                 clocks = <&ref>;
  69                                 clock-names = "uart";
  70
  71                                 status = "disabled";
  72                         };
  73
  74                         gpio: gpio@18040000 {
  75                                 compatible = "qca,ar7100-gpio";
  76                                 reg = <0x18040000 0x34>;
  77                                 interrupts = <2>;
  78
  79                                 ngpios = <30>;
  80
  81                                 gpio-controller;
  82                                 #gpio-cells = <2>;
  83
  84                                 interrupt-controller;
  85                                 #interrupt-cells = <2>;
  86
  87                                 status = "disabled";
  88                         };
  89
  90                         pll: pll-controller@18050000 {
  91                                 compatible = "qca,ar9330-pll";
  92                                 reg = <0x18050000 0x100>;
  93
  94                                 clocks = <&ref>;
  95                                 clock-names = "ref";
  96
  97                                 #clock-cells = <1>;
  98                         };
  99
 100                         miscintc: interrupt-controller@18060010 {
 101                                 compatible = "qca,ar7240-misc-intc";
 102                                 reg = <0x18060010 0x8>;
 103
 104                                 interrupt-parent = <&cpuintc>;
 105                                 interrupts = <6>;
 106
 107                                 interrupt-controller;
 108                                 #interrupt-cells = <1>;
 109                         };
 110
 111                         rst: reset-controller@1806001c {
 112                                 compatible = "qca,ar7100-reset";
 113                                 reg = <0x1806001c 0x4>;
 114
 115                                 #reset-cells = <1>;
 116                         };
 117                 };
 118
 119                 eth0: ethernet@19000000 {
 120                         compatible = "qca,ar9330-eth";
 121                         reg = <0x19000000 0x200>;
 122                         interrupts = <4>;
 123
 124                         resets = <&rst 9>, <&rst 22>;
 125                         reset-names = "mac", "mdio";
 126                         clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_AHB>;
 127                         clock-names = "eth", "mdio";
 128
 129                         phy-mode = "mii";
 130                         phy-handle = <&phy_port4>;
 131
 132                         status = "disabled";
 133                 };
 134
 135                 eth1: ethernet@1a000000 {
 136                         compatible = "qca,ar9330-eth";
 137                         reg = <0x1a000000 0x200>;
 138                         interrupts = <5>;
 139                         resets = <&rst 13>, <&rst 23>;
 140                         reset-names = "mac", "mdio";
 141                         clocks = <&pll ATH79_CLK_AHB>, <&pll ATH79_CLK_AHB>;
 142                         clock-names = "eth", "mdio";
 143
 144                         phy-mode = "gmii";
 145
 146                         status = "disabled";
 147
 148                         fixed-link {
 149                                 speed = <1000>;
 150                                 full-duplex;
 151                                 pause;
 152                         };
 153
 154                         mdio {
 155                                 #address-cells = <1>;
 156                                 #size-cells = <0>;
 157
 158                                 switch10: switch@10 {
 159                                         #address-cells = <1>;
 160                                         #size-cells = <0>;
 161
 162                                         compatible = "qca,ar9331-switch";
 163                                         reg = <0x10>;
 164                                         resets = <&rst 8>;
 165                                         reset-names = "switch";
 166
 167                                         interrupt-parent = <&miscintc>;
 168                                         interrupts = <12>;
 169
 170                                         interrupt-controller;
 171                                         #interrupt-cells = <1>;
 172
 173                                         ports {
 174                                                 #address-cells = <1>;
 175                                                 #size-cells = <0>;
 176
 177                                                 switch_port0: port@0 {
 178                                                         reg = <0x0>;
 179                                                         label = "cpu";
 180                                                         ethernet = <&eth1>;
 181
 182                                                         phy-mode = "gmii";
 183
 184                                                         fixed-link {
 185                                                                 speed = <1000>;
 186                                                                 full-duplex;
 187                                                                 pause;
 188                                                         };
 189                                                 };
 190
 191                                                 switch_port1: port@1 {
 192                                                         reg = <0x1>;
 193                                                         phy-handle = <&phy_port0>;
 194                                                         phy-mode = "internal";
 195
 196                                                         status = "disabled";
 197                                                 };
 198
 199                                                 switch_port2: port@2 {
 200                                                         reg = <0x2>;
 201                                                         phy-handle = <&phy_port1>;
 202                                                         phy-mode = "internal";
 203
 204                                                         status = "disabled";
 205                                                 };
 206
 207                                                 switch_port3: port@3 {
 208                                                         reg = <0x3>;
 209                                                         phy-handle = <&phy_port2>;
 210                                                         phy-mode = "internal";
 211
 212                                                         status = "disabled";
 213                                                 };
 214
 215                                                 switch_port4: port@4 {
 216                                                         reg = <0x4>;
 217                                                         phy-handle = <&phy_port3>;
 218                                                         phy-mode = "internal";
 219
 220                                                         status = "disabled";
 221                                                 };
 222                                         };
 223
 224                                         mdio {
 225                                                 #address-cells = <1>;
 226                                                 #size-cells = <0>;
 227
 228                                                 interrupt-parent = <&switch10>;
 229
 230                                                 phy_port0: phy@0 {
 231                                                         reg = <0x0>;
 232                                                         interrupts = <0>;
 233                                                         status = "disabled";
 234                                                 };
 235
 236                                                 phy_port1: phy@1 {
 237                                                         reg = <0x1>;
 238                                                         interrupts = <0>;
 239                                                         status = "disabled";
 240                                                 };
 241
 242                                                 phy_port2: phy@2 {
 243                                                         reg = <0x2>;
 244                                                         interrupts = <0>;
 245                                                         status = "disabled";
 246                                                 };
 247
 248                                                 phy_port3: phy@3 {
 249                                                         reg = <0x3>;
 250                                                         interrupts = <0>;
 251                                                         status = "disabled";
 252                                                 };
 253
 254                                                 phy_port4: phy@4 {
 255                                                         reg = <0x4>;
 256                                                         interrupts = <0>;
 257                                                         status = "disabled";
 258                                                 };
 259                                         };
 260                                 };
 261                         };
 262                 };
 263
 264                 usb: usb@1b000100 {
 265                         compatible = "chipidea,usb2";
 266                         reg = <0x1b000000 0x200>;
 267
 268                         interrupts = <3>;
 269                         resets = <&rst 5>;
 270
 271                         phy-names = "usb-phy";
 272                         phys = <&usb_phy>;
 273
 274                         status = "disabled";
 275                 };
 276
 277                 spi: spi@1f000000 {
 278                         compatible = "qca,ar7100-spi";
 279                         reg = <0x1f000000 0x10>;
 280
 281                         clocks = <&pll ATH79_CLK_AHB>;
 282                         clock-names = "ahb";
 283
 284                         #address-cells = <1>;
 285                         #size-cells = <0>;
 286
 287                         status = "disabled";
 288                 };
 289         };
 290
 291         usb_phy: usb-phy {
 292                 compatible = "qca,ar7100-usb-phy";
 293
 294                 reset-names = "phy", "suspend-override";
 295                 resets = <&rst 4>, <&rst 3>;
 296
 297                 #phy-cells = <0>;
 298
 299                 status = "disabled";
 300         };
 301 };