arch/mips/alchemy/devboards/db1550.c

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * Alchemy Db1550/Pb1550 board support
   4  *
   5  * (c) 2011 Manuel Lauss <manuel.lauss@googlemail.com>
   6  */
   7
   8 #include <linux/clk.h>
   9 #include <linux/dma-mapping.h>
  10 #include <linux/gpio.h>
  11 #include <linux/i2c.h>
  12 #include <linux/init.h>
  13 #include <linux/io.h>
  14 #include <linux/interrupt.h>
  15 #include <linux/mtd/mtd.h>
  16 #include <linux/mtd/platnand.h>
  17 #include <linux/platform_device.h>
  18 #include <linux/pm.h>
  19 #include <linux/spi/spi.h>
  20 #include <linux/spi/flash.h>
  21 #include <asm/bootinfo.h>
  22 #include <asm/mach-au1x00/au1000.h>
  23 #include <asm/mach-au1x00/gpio-au1000.h>
  24 #include <asm/mach-au1x00/au1xxx_eth.h>
  25 #include <asm/mach-au1x00/au1xxx_dbdma.h>
  26 #include <asm/mach-au1x00/au1xxx_psc.h>
  27 #include <asm/mach-au1x00/au1550_spi.h>
  28 #include <asm/mach-au1x00/au1550nd.h>
  29 #include <asm/mach-db1x00/bcsr.h>
  30 #include <prom.h>
  31 #include "platform.h"
  32
  33 static void __init db1550_hw_setup(void)
  34 {
  35         void __iomem *base;
  36         unsigned long v;
  37
  38         /* complete pin setup: assign GPIO16 to PSC0_SYNC1 (SPI cs# line)
  39          * as well as PSC1_SYNC for AC97 on PB1550.
  40          */
  41         v = alchemy_rdsys(AU1000_SYS_PINFUNC);
  42         alchemy_wrsys(v | 1 | SYS_PF_PSC1_S1, AU1000_SYS_PINFUNC);
  43
  44         /* reset the AC97 codec now, the reset time in the psc-ac97 driver
  45          * is apparently too short although it's ridiculous as it is.
  46          */
  47         base = (void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR);
  48         __raw_writel(PSC_SEL_CLK_SERCLK | PSC_SEL_PS_AC97MODE,
  49                      base + PSC_SEL_OFFSET);
  50         __raw_writel(PSC_CTRL_DISABLE, base + PSC_CTRL_OFFSET);
  51         wmb();
  52         __raw_writel(PSC_AC97RST_RST, base + PSC_AC97RST_OFFSET);
  53         wmb();
  54 }
  55
  56 int __init db1550_board_setup(void)
  57 {
  58         unsigned short whoami;
  59
  60         bcsr_init(DB1550_BCSR_PHYS_ADDR,
  61                   DB1550_BCSR_PHYS_ADDR + DB1550_BCSR_HEXLED_OFS);
  62
  63         whoami = bcsr_read(BCSR_WHOAMI); /* PB1550 hexled offset differs */
  64         switch (BCSR_WHOAMI_BOARD(whoami)) {
  65         case BCSR_WHOAMI_PB1550_SDR:
  66         case BCSR_WHOAMI_PB1550_DDR:
  67                 bcsr_init(PB1550_BCSR_PHYS_ADDR,
  68                           PB1550_BCSR_PHYS_ADDR + PB1550_BCSR_HEXLED_OFS);
  69                 break;
  70         case BCSR_WHOAMI_DB1550:
  71                 break;
  72         default:
  73                 return -ENODEV;
  74         }
  75
  76         pr_info("Alchemy/AMD %s Board, CPLD Rev %d Board-ID %d  "       \
  77                 "Daughtercard ID %d\n", get_system_type(),
  78                 (whoami >> 4) & 0xf, (whoami >> 8) & 0xf, whoami & 0xf);
  79
  80         db1550_hw_setup();
  81         return 0;
  82 }
  83
  84 /*****************************************************************************/
  85
  86 static u64 au1550_all_dmamask = DMA_BIT_MASK(32);
  87
  88 static struct mtd_partition db1550_spiflash_parts[] = {
  89         {
  90                 .name   = "spi_flash",
  91                 .offset = 0,
  92                 .size   = MTDPART_SIZ_FULL,
  93         },
  94 };
  95
  96 static struct flash_platform_data db1550_spiflash_data = {
  97         .name           = "s25fl010",
  98         .parts          = db1550_spiflash_parts,
  99         .nr_parts       = ARRAY_SIZE(db1550_spiflash_parts),
 100         .type           = "m25p10",
 101 };
 102
 103 static struct spi_board_info db1550_spi_devs[] __initdata = {
 104         {
 105                 /* TI TMP121AIDBVR temp sensor */
 106                 .modalias       = "tmp121",
 107                 .max_speed_hz   = 2400000,
 108                 .bus_num        = 0,
 109                 .chip_select    = 0,
 110                 .mode           = SPI_MODE_0,
 111         },
 112         {
 113                 /* Spansion S25FL001D0FMA SPI flash */
 114                 .modalias       = "m25p80",
 115                 .max_speed_hz   = 2400000,
 116                 .bus_num        = 0,
 117                 .chip_select    = 1,
 118                 .mode           = SPI_MODE_0,
 119                 .platform_data  = &db1550_spiflash_data,
 120         },
 121 };
 122
 123 static struct i2c_board_info db1550_i2c_devs[] __initdata = {
 124         { I2C_BOARD_INFO("24c04",  0x52),}, /* AT24C04-10 I2C eeprom */
 125         { I2C_BOARD_INFO("ne1619", 0x2d),}, /* adm1025-compat hwmon */
 126         { I2C_BOARD_INFO("wm8731", 0x1b),}, /* I2S audio codec WM8731 */
 127 };
 128
 129 /**********************************************************************/
 130
 131 static void au1550_nand_cmd_ctrl(struct nand_chip *this, int cmd,
 132                                  unsigned int ctrl)
 133 {
 134         unsigned long ioaddr = (unsigned long)this->legacy.IO_ADDR_W;
 135
 136         ioaddr &= 0xffffff00;
 137
 138         if (ctrl & NAND_CLE) {
 139                 ioaddr += MEM_STNAND_CMD;
 140         } else if (ctrl & NAND_ALE) {
 141                 ioaddr += MEM_STNAND_ADDR;
 142         } else {
 143                 /* assume we want to r/w real data  by default */
 144                 ioaddr += MEM_STNAND_DATA;
 145         }
 146         this->legacy.IO_ADDR_R = this->legacy.IO_ADDR_W = (void __iomem *)ioaddr;
 147         if (cmd != NAND_CMD_NONE) {
 148                 __raw_writeb(cmd, this->legacy.IO_ADDR_W);
 149                 wmb();
 150         }
 151 }
 152
 153 static int au1550_nand_device_ready(struct nand_chip *this)
 154 {
 155         return alchemy_rdsmem(AU1000_MEM_STSTAT) & 1;
 156 }
 157
 158 static struct mtd_partition db1550_nand_parts[] = {
 159         {
 160                 .name   = "NAND FS 0",
 161                 .offset = 0,
 162                 .size   = 8 * 1024 * 1024,
 163         },
 164         {
 165                 .name   = "NAND FS 1",
 166                 .offset = MTDPART_OFS_APPEND,
 167                 .size   = MTDPART_SIZ_FULL
 168         },
 169 };
 170
 171 struct platform_nand_data db1550_nand_platdata = {
 172         .chip = {
 173                 .nr_chips       = 1,
 174                 .chip_offset    = 0,
 175                 .nr_partitions  = ARRAY_SIZE(db1550_nand_parts),
 176                 .partitions     = db1550_nand_parts,
 177                 .chip_delay     = 20,
 178         },
 179         .ctrl = {
 180                 .dev_ready      = au1550_nand_device_ready,
 181                 .cmd_ctrl       = au1550_nand_cmd_ctrl,
 182         },
 183 };
 184
 185 static struct resource db1550_nand_res[] = {
 186         [0] = {
 187                 .start  = 0x20000000,
 188                 .end    = 0x200000ff,
 189                 .flags  = IORESOURCE_MEM,
 190         },
 191 };
 192
 193 static struct platform_device db1550_nand_dev = {
 194         .name           = "gen_nand",
 195         .num_resources  = ARRAY_SIZE(db1550_nand_res),
 196         .resource       = db1550_nand_res,
 197         .id             = -1,
 198         .dev            = {
 199                 .platform_data = &db1550_nand_platdata,
 200         }
 201 };
 202
 203 static struct au1550nd_platdata pb1550_nand_pd = {
 204         .parts          = db1550_nand_parts,
 205         .num_parts      = ARRAY_SIZE(db1550_nand_parts),
 206         .devwidth       = 0,    /* x8 NAND default, needs fixing up */
 207 };
 208
 209 static struct platform_device pb1550_nand_dev = {
 210         .name           = "au1550-nand",
 211         .id             = -1,
 212         .resource       = db1550_nand_res,
 213         .num_resources  = ARRAY_SIZE(db1550_nand_res),
 214         .dev            = {
 215                 .platform_data  = &pb1550_nand_pd,
 216         },
 217 };
 218
 219 static void __init pb1550_nand_setup(void)
 220 {
 221         int boot_swapboot = (alchemy_rdsmem(AU1000_MEM_STSTAT) & (0x7 << 1)) |
 222                             ((bcsr_read(BCSR_STATUS) >> 6) & 0x1);
 223
 224         gpio_direction_input(206);      /* de-assert NAND CS# */
 225         switch (boot_swapboot) {
 226         case 0: case 2: case 8: case 0xC: case 0xD:
 227                 /* x16 NAND Flash */
 228                 pb1550_nand_pd.devwidth = 1;
 229                 fallthrough;
 230         case 1: case 3: case 9: case 0xE: case 0xF:
 231                 /* x8 NAND, already set up */
 232                 platform_device_register(&pb1550_nand_dev);
 233         }
 234 }
 235
 236 /**********************************************************************/
 237
 238 static struct resource au1550_psc0_res[] = {
 239         [0] = {
 240                 .start  = AU1550_PSC0_PHYS_ADDR,
 241                 .end    = AU1550_PSC0_PHYS_ADDR + 0xfff,
 242                 .flags  = IORESOURCE_MEM,
 243         },
 244         [1] = {
 245                 .start  = AU1550_PSC0_INT,
 246                 .end    = AU1550_PSC0_INT,
 247                 .flags  = IORESOURCE_IRQ,
 248         },
 249         [2] = {
 250                 .start  = AU1550_DSCR_CMD0_PSC0_TX,
 251                 .end    = AU1550_DSCR_CMD0_PSC0_TX,
 252                 .flags  = IORESOURCE_DMA,
 253         },
 254         [3] = {
 255                 .start  = AU1550_DSCR_CMD0_PSC0_RX,
 256                 .end    = AU1550_DSCR_CMD0_PSC0_RX,
 257                 .flags  = IORESOURCE_DMA,
 258         },
 259 };
 260
 261 static void db1550_spi_cs_en(struct au1550_spi_info *spi, int cs, int pol)
 262 {
 263         if (cs)
 264                 bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SPISEL);
 265         else
 266                 bcsr_mod(BCSR_BOARD, BCSR_BOARD_SPISEL, 0);
 267 }
 268
 269 static struct au1550_spi_info db1550_spi_platdata = {
 270         .mainclk_hz     = 48000000,     /* PSC0 clock: max. 2.4MHz SPI clk */
 271         .num_chipselect = 2,
 272         .activate_cs    = db1550_spi_cs_en,
 273 };
 274
 275
 276 static struct platform_device db1550_spi_dev = {
 277         .dev    = {
 278                 .dma_mask               = &au1550_all_dmamask,
 279                 .coherent_dma_mask      = DMA_BIT_MASK(32),
 280                 .platform_data          = &db1550_spi_platdata,
 281         },
 282         .name           = "au1550-spi",
 283         .id             = 0,    /* bus number */
 284         .num_resources  = ARRAY_SIZE(au1550_psc0_res),
 285         .resource       = au1550_psc0_res,
 286 };
 287
 288 /**********************************************************************/
 289
 290 static struct resource au1550_psc1_res[] = {
 291         [0] = {
 292                 .start  = AU1550_PSC1_PHYS_ADDR,
 293                 .end    = AU1550_PSC1_PHYS_ADDR + 0xfff,
 294                 .flags  = IORESOURCE_MEM,
 295         },
 296         [1] = {
 297                 .start  = AU1550_PSC1_INT,
 298                 .end    = AU1550_PSC1_INT,
 299                 .flags  = IORESOURCE_IRQ,
 300         },
 301         [2] = {
 302                 .start  = AU1550_DSCR_CMD0_PSC1_TX,
 303                 .end    = AU1550_DSCR_CMD0_PSC1_TX,
 304                 .flags  = IORESOURCE_DMA,
 305         },
 306         [3] = {
 307                 .start  = AU1550_DSCR_CMD0_PSC1_RX,
 308                 .end    = AU1550_DSCR_CMD0_PSC1_RX,
 309                 .flags  = IORESOURCE_DMA,
 310         },
 311 };
 312
 313 static struct platform_device db1550_ac97_dev = {
 314         .name           = "au1xpsc_ac97",
 315         .id             = 1,    /* PSC ID */
 316         .num_resources  = ARRAY_SIZE(au1550_psc1_res),
 317         .resource       = au1550_psc1_res,
 318 };
 319
 320
 321 static struct resource au1550_psc2_res[] = {
 322         [0] = {
 323                 .start  = AU1550_PSC2_PHYS_ADDR,
 324                 .end    = AU1550_PSC2_PHYS_ADDR + 0xfff,
 325                 .flags  = IORESOURCE_MEM,
 326         },
 327         [1] = {
 328                 .start  = AU1550_PSC2_INT,
 329                 .end    = AU1550_PSC2_INT,
 330                 .flags  = IORESOURCE_IRQ,
 331         },
 332         [2] = {
 333                 .start  = AU1550_DSCR_CMD0_PSC2_TX,
 334                 .end    = AU1550_DSCR_CMD0_PSC2_TX,
 335                 .flags  = IORESOURCE_DMA,
 336         },
 337         [3] = {
 338                 .start  = AU1550_DSCR_CMD0_PSC2_RX,
 339                 .end    = AU1550_DSCR_CMD0_PSC2_RX,
 340                 .flags  = IORESOURCE_DMA,
 341         },
 342 };
 343
 344 static struct platform_device db1550_i2c_dev = {
 345         .name           = "au1xpsc_smbus",
 346         .id             = 0,    /* bus number */
 347         .num_resources  = ARRAY_SIZE(au1550_psc2_res),
 348         .resource       = au1550_psc2_res,
 349 };
 350
 351 /**********************************************************************/
 352
 353 static struct resource au1550_psc3_res[] = {
 354         [0] = {
 355                 .start  = AU1550_PSC3_PHYS_ADDR,
 356                 .end    = AU1550_PSC3_PHYS_ADDR + 0xfff,
 357                 .flags  = IORESOURCE_MEM,
 358         },
 359         [1] = {
 360                 .start  = AU1550_PSC3_INT,
 361                 .end    = AU1550_PSC3_INT,
 362                 .flags  = IORESOURCE_IRQ,
 363         },
 364         [2] = {
 365                 .start  = AU1550_DSCR_CMD0_PSC3_TX,
 366                 .end    = AU1550_DSCR_CMD0_PSC3_TX,
 367                 .flags  = IORESOURCE_DMA,
 368         },
 369         [3] = {
 370                 .start  = AU1550_DSCR_CMD0_PSC3_RX,
 371                 .end    = AU1550_DSCR_CMD0_PSC3_RX,
 372                 .flags  = IORESOURCE_DMA,
 373         },
 374 };
 375
 376 static struct platform_device db1550_i2s_dev = {
 377         .name           = "au1xpsc_i2s",
 378         .id             = 3,    /* PSC ID */
 379         .num_resources  = ARRAY_SIZE(au1550_psc3_res),
 380         .resource       = au1550_psc3_res,
 381 };
 382
 383 /**********************************************************************/
 384
 385 static struct platform_device db1550_stac_dev = {
 386         .name           = "ac97-codec",
 387         .id             = 1,    /* on PSC1 */
 388 };
 389
 390 static struct platform_device db1550_ac97dma_dev = {
 391         .name           = "au1xpsc-pcm",
 392         .id             = 1,    /* on PSC3 */
 393 };
 394
 395 static struct platform_device db1550_i2sdma_dev = {
 396         .name           = "au1xpsc-pcm",
 397         .id             = 3,    /* on PSC3 */
 398 };
 399
 400 static struct platform_device db1550_sndac97_dev = {
 401         .name           = "db1550-ac97",
 402         .dev = {
 403                 .dma_mask               = &au1550_all_dmamask,
 404                 .coherent_dma_mask      = DMA_BIT_MASK(32),
 405         },
 406 };
 407
 408 static struct platform_device db1550_sndi2s_dev = {
 409         .name           = "db1550-i2s",
 410         .dev = {
 411                 .dma_mask               = &au1550_all_dmamask,
 412                 .coherent_dma_mask      = DMA_BIT_MASK(32),
 413         },
 414 };
 415
 416 /**********************************************************************/
 417
 418 static int db1550_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
 419 {
 420         if ((slot < 11) || (slot > 13) || pin == 0)
 421                 return -1;
 422         if (slot == 11)
 423                 return (pin == 1) ? AU1550_PCI_INTC : 0xff;
 424         if (slot == 12) {
 425                 switch (pin) {
 426                 case 1: return AU1550_PCI_INTB;
 427                 case 2: return AU1550_PCI_INTC;
 428                 case 3: return AU1550_PCI_INTD;
 429                 case 4: return AU1550_PCI_INTA;
 430                 }
 431         }
 432         if (slot == 13) {
 433                 switch (pin) {
 434                 case 1: return AU1550_PCI_INTA;
 435                 case 2: return AU1550_PCI_INTB;
 436                 case 3: return AU1550_PCI_INTC;
 437                 case 4: return AU1550_PCI_INTD;
 438                 }
 439         }
 440         return -1;
 441 }
 442
 443 static int pb1550_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
 444 {
 445         if ((slot < 12) || (slot > 13) || pin == 0)
 446                 return -1;
 447         if (slot == 12) {
 448                 switch (pin) {
 449                 case 1: return AU1500_PCI_INTB;
 450                 case 2: return AU1500_PCI_INTC;
 451                 case 3: return AU1500_PCI_INTD;
 452                 case 4: return AU1500_PCI_INTA;
 453                 }
 454         }
 455         if (slot == 13) {
 456                 switch (pin) {
 457                 case 1: return AU1500_PCI_INTA;
 458                 case 2: return AU1500_PCI_INTB;
 459                 case 3: return AU1500_PCI_INTC;
 460                 case 4: return AU1500_PCI_INTD;
 461                 }
 462         }
 463         return -1;
 464 }
 465
 466 static struct resource alchemy_pci_host_res[] = {
 467         [0] = {
 468                 .start  = AU1500_PCI_PHYS_ADDR,
 469                 .end    = AU1500_PCI_PHYS_ADDR + 0xfff,
 470                 .flags  = IORESOURCE_MEM,
 471         },
 472 };
 473
 474 static struct alchemy_pci_platdata db1550_pci_pd = {
 475         .board_map_irq  = db1550_map_pci_irq,
 476 };
 477
 478 static struct platform_device db1550_pci_host_dev = {
 479         .dev.platform_data = &db1550_pci_pd,
 480         .name           = "alchemy-pci",
 481         .id             = 0,
 482         .num_resources  = ARRAY_SIZE(alchemy_pci_host_res),
 483         .resource       = alchemy_pci_host_res,
 484 };
 485
 486 /**********************************************************************/
 487
 488 static struct platform_device *db1550_devs[] __initdata = {
 489         &db1550_i2c_dev,
 490         &db1550_ac97_dev,
 491         &db1550_spi_dev,
 492         &db1550_i2s_dev,
 493         &db1550_stac_dev,
 494         &db1550_ac97dma_dev,
 495         &db1550_i2sdma_dev,
 496         &db1550_sndac97_dev,
 497         &db1550_sndi2s_dev,
 498 };
 499
 500 /* must be arch_initcall; MIPS PCI scans busses in a subsys_initcall */
 501 int __init db1550_pci_setup(int id)
 502 {
 503         if (id)
 504                 db1550_pci_pd.board_map_irq = pb1550_map_pci_irq;
 505         return platform_device_register(&db1550_pci_host_dev);
 506 }
 507
 508 static void __init db1550_devices(void)
 509 {
 510         alchemy_gpio_direction_output(203, 0);  /* red led on */
 511
 512         irq_set_irq_type(AU1550_GPIO0_INT, IRQ_TYPE_EDGE_BOTH);  /* CD0# */
 513         irq_set_irq_type(AU1550_GPIO1_INT, IRQ_TYPE_EDGE_BOTH);  /* CD1# */
 514         irq_set_irq_type(AU1550_GPIO3_INT, IRQ_TYPE_LEVEL_LOW);  /* CARD0# */
 515         irq_set_irq_type(AU1550_GPIO5_INT, IRQ_TYPE_LEVEL_LOW);  /* CARD1# */
 516         irq_set_irq_type(AU1550_GPIO21_INT, IRQ_TYPE_LEVEL_LOW); /* STSCHG0# */
 517         irq_set_irq_type(AU1550_GPIO22_INT, IRQ_TYPE_LEVEL_LOW); /* STSCHG1# */
 518
 519         db1x_register_pcmcia_socket(
 520                 AU1000_PCMCIA_ATTR_PHYS_ADDR,
 521                 AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
 522                 AU1000_PCMCIA_MEM_PHYS_ADDR,
 523                 AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x000400000 - 1,
 524                 AU1000_PCMCIA_IO_PHYS_ADDR,
 525                 AU1000_PCMCIA_IO_PHYS_ADDR   + 0x000010000 - 1,
 526                 AU1550_GPIO3_INT, 0,
 527                 /*AU1550_GPIO21_INT*/0, 0, 0);
 528
 529         db1x_register_pcmcia_socket(
 530                 AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
 531                 AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
 532                 AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x004000000,
 533                 AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x004400000 - 1,
 534                 AU1000_PCMCIA_IO_PHYS_ADDR   + 0x004000000,
 535                 AU1000_PCMCIA_IO_PHYS_ADDR   + 0x004010000 - 1,
 536                 AU1550_GPIO5_INT, 1,
 537                 /*AU1550_GPIO22_INT*/0, 0, 1);
 538
 539         platform_device_register(&db1550_nand_dev);
 540
 541         alchemy_gpio_direction_output(202, 0);  /* green led on */
 542 }
 543
 544 static void __init pb1550_devices(void)
 545 {
 546         irq_set_irq_type(AU1550_GPIO0_INT, IRQ_TYPE_LEVEL_LOW);
 547         irq_set_irq_type(AU1550_GPIO1_INT, IRQ_TYPE_LEVEL_LOW);
 548         irq_set_irq_type(AU1550_GPIO201_205_INT, IRQ_TYPE_LEVEL_HIGH);
 549
 550         /* enable both PCMCIA card irqs in the shared line */
 551         alchemy_gpio2_enable_int(201);  /* socket 0 card irq */
 552         alchemy_gpio2_enable_int(202);  /* socket 1 card irq */
 553
 554         /* Pb1550, like all others, also has statuschange irqs; however they're
 555         * wired up on one of the Au1550's shared GPIO201_205 line, which also
 556         * services the PCMCIA card interrupts.  So we ignore statuschange and
 557         * use the GPIO201_205 exclusively for card interrupts, since a) pcmcia
 558         * drivers are used to shared irqs and b) statuschange isn't really use-
 559         * ful anyway.
 560         */
 561         db1x_register_pcmcia_socket(
 562                 AU1000_PCMCIA_ATTR_PHYS_ADDR,
 563                 AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
 564                 AU1000_PCMCIA_MEM_PHYS_ADDR,
 565                 AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x000400000 - 1,
 566                 AU1000_PCMCIA_IO_PHYS_ADDR,
 567                 AU1000_PCMCIA_IO_PHYS_ADDR   + 0x000010000 - 1,
 568                 AU1550_GPIO201_205_INT, AU1550_GPIO0_INT, 0, 0, 0);
 569
 570         db1x_register_pcmcia_socket(
 571                 AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008000000,
 572                 AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1,
 573                 AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x008000000,
 574                 AU1000_PCMCIA_MEM_PHYS_ADDR  + 0x008400000 - 1,
 575                 AU1000_PCMCIA_IO_PHYS_ADDR   + 0x008000000,
 576                 AU1000_PCMCIA_IO_PHYS_ADDR   + 0x008010000 - 1,
 577                 AU1550_GPIO201_205_INT, AU1550_GPIO1_INT, 0, 0, 1);
 578
 579         pb1550_nand_setup();
 580 }
 581
 582 int __init db1550_dev_setup(void)
 583 {
 584         int swapped, id;
 585         struct clk *c;
 586
 587         id = (BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI)) != BCSR_WHOAMI_DB1550);
 588
 589         i2c_register_board_info(0, db1550_i2c_devs,
 590                                 ARRAY_SIZE(db1550_i2c_devs));
 591         spi_register_board_info(db1550_spi_devs,
 592                                 ARRAY_SIZE(db1550_i2c_devs));
 593
 594         c = clk_get(NULL, "psc0_intclk");
 595         if (!IS_ERR(c)) {
 596                 clk_set_rate(c, 50000000);
 597                 clk_prepare_enable(c);
 598                 clk_put(c);
 599         }
 600         c = clk_get(NULL, "psc2_intclk");
 601         if (!IS_ERR(c)) {
 602                 clk_set_rate(c, db1550_spi_platdata.mainclk_hz);
 603                 clk_prepare_enable(c);
 604                 clk_put(c);
 605         }
 606
 607         /* Audio PSC clock is supplied by codecs (PSC1, 3) FIXME: platdata!! */
 608         __raw_writel(PSC_SEL_CLK_SERCLK,
 609             (void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR) + PSC_SEL_OFFSET);
 610         wmb();
 611         __raw_writel(PSC_SEL_CLK_SERCLK,
 612             (void __iomem *)KSEG1ADDR(AU1550_PSC3_PHYS_ADDR) + PSC_SEL_OFFSET);
 613         wmb();
 614         /* SPI/I2C use internally supplied 50MHz source */
 615         __raw_writel(PSC_SEL_CLK_INTCLK,
 616             (void __iomem *)KSEG1ADDR(AU1550_PSC0_PHYS_ADDR) + PSC_SEL_OFFSET);
 617         wmb();
 618         __raw_writel(PSC_SEL_CLK_INTCLK,
 619             (void __iomem *)KSEG1ADDR(AU1550_PSC2_PHYS_ADDR) + PSC_SEL_OFFSET);
 620         wmb();
 621
 622         id ? pb1550_devices() : db1550_devices();
 623
 624         swapped = bcsr_read(BCSR_STATUS) &
 625                (id ? BCSR_STATUS_PB1550_SWAPBOOT : BCSR_STATUS_DB1000_SWAPBOOT);
 626         db1x_register_norflash(128 << 20, 4, swapped);
 627
 628         return platform_add_devices(db1550_devs, ARRAY_SIZE(db1550_devs));
 629 }