1 // SPDX-License-Identifier: GPL-2.0
3 * Alchemy Db1550/Pb1550 board support
5 * (c) 2011 Manuel Lauss <manuel.lauss@googlemail.com>
9 #include <linux/dma-mapping.h>
10 #include <linux/gpio.h>
11 #include <linux/i2c.h>
12 #include <linux/init.h>
14 #include <linux/interrupt.h>
15 #include <linux/mtd/mtd.h>
16 #include <linux/mtd/platnand.h>
17 #include <linux/platform_device.h>
19 #include <linux/spi/spi.h>
20 #include <linux/spi/flash.h>
21 #include <asm/bootinfo.h>
22 #include <asm/mach-au1x00/au1000.h>
23 #include <asm/mach-au1x00/gpio-au1000.h>
24 #include <asm/mach-au1x00/au1xxx_eth.h>
25 #include <asm/mach-au1x00/au1xxx_dbdma.h>
26 #include <asm/mach-au1x00/au1xxx_psc.h>
27 #include <asm/mach-au1x00/au1550_spi.h>
28 #include <asm/mach-au1x00/au1550nd.h>
29 #include <asm/mach-db1x00/bcsr.h>
33 static void __init db1550_hw_setup(void)
38 /* complete pin setup: assign GPIO16 to PSC0_SYNC1 (SPI cs# line)
39 * as well as PSC1_SYNC for AC97 on PB1550.
41 v = alchemy_rdsys(AU1000_SYS_PINFUNC);
42 alchemy_wrsys(v | 1 | SYS_PF_PSC1_S1, AU1000_SYS_PINFUNC);
44 /* reset the AC97 codec now, the reset time in the psc-ac97 driver
45 * is apparently too short although it's ridiculous as it is.
47 base = (void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR);
48 __raw_writel(PSC_SEL_CLK_SERCLK | PSC_SEL_PS_AC97MODE,
49 base + PSC_SEL_OFFSET);
50 __raw_writel(PSC_CTRL_DISABLE, base + PSC_CTRL_OFFSET);
52 __raw_writel(PSC_AC97RST_RST, base + PSC_AC97RST_OFFSET);
56 int __init db1550_board_setup(void)
58 unsigned short whoami;
60 bcsr_init(DB1550_BCSR_PHYS_ADDR,
61 DB1550_BCSR_PHYS_ADDR + DB1550_BCSR_HEXLED_OFS);
63 whoami = bcsr_read(BCSR_WHOAMI); /* PB1550 hexled offset differs */
64 switch (BCSR_WHOAMI_BOARD(whoami)) {
65 case BCSR_WHOAMI_PB1550_SDR:
66 case BCSR_WHOAMI_PB1550_DDR:
67 bcsr_init(PB1550_BCSR_PHYS_ADDR,
68 PB1550_BCSR_PHYS_ADDR + PB1550_BCSR_HEXLED_OFS);
70 case BCSR_WHOAMI_DB1550:
76 pr_info("Alchemy/AMD %s Board, CPLD Rev %d Board-ID %d " \
77 "Daughtercard ID %d\n", get_system_type(),
78 (whoami >> 4) & 0xf, (whoami >> 8) & 0xf, whoami & 0xf);
84 /*****************************************************************************/
86 static u64 au1550_all_dmamask = DMA_BIT_MASK(32);
88 static struct mtd_partition db1550_spiflash_parts[] = {
92 .size = MTDPART_SIZ_FULL,
96 static struct flash_platform_data db1550_spiflash_data = {
98 .parts = db1550_spiflash_parts,
99 .nr_parts = ARRAY_SIZE(db1550_spiflash_parts),
103 static struct spi_board_info db1550_spi_devs[] __initdata = {
105 /* TI TMP121AIDBVR temp sensor */
106 .modalias = "tmp121",
107 .max_speed_hz = 2400000,
113 /* Spansion S25FL001D0FMA SPI flash */
114 .modalias = "m25p80",
115 .max_speed_hz = 2400000,
119 .platform_data = &db1550_spiflash_data,
123 static struct i2c_board_info db1550_i2c_devs[] __initdata = {
124 { I2C_BOARD_INFO("24c04", 0x52),}, /* AT24C04-10 I2C eeprom */
125 { I2C_BOARD_INFO("ne1619", 0x2d),}, /* adm1025-compat hwmon */
126 { I2C_BOARD_INFO("wm8731", 0x1b),}, /* I2S audio codec WM8731 */
129 /**********************************************************************/
131 static void au1550_nand_cmd_ctrl(struct nand_chip *this, int cmd,
134 unsigned long ioaddr = (unsigned long)this->legacy.IO_ADDR_W;
136 ioaddr &= 0xffffff00;
138 if (ctrl & NAND_CLE) {
139 ioaddr += MEM_STNAND_CMD;
140 } else if (ctrl & NAND_ALE) {
141 ioaddr += MEM_STNAND_ADDR;
143 /* assume we want to r/w real data by default */
144 ioaddr += MEM_STNAND_DATA;
146 this->legacy.IO_ADDR_R = this->legacy.IO_ADDR_W = (void __iomem *)ioaddr;
147 if (cmd != NAND_CMD_NONE) {
148 __raw_writeb(cmd, this->legacy.IO_ADDR_W);
153 static int au1550_nand_device_ready(struct nand_chip *this)
155 return alchemy_rdsmem(AU1000_MEM_STSTAT) & 1;
158 static struct mtd_partition db1550_nand_parts[] = {
162 .size = 8 * 1024 * 1024,
166 .offset = MTDPART_OFS_APPEND,
167 .size = MTDPART_SIZ_FULL
171 struct platform_nand_data db1550_nand_platdata = {
175 .nr_partitions = ARRAY_SIZE(db1550_nand_parts),
176 .partitions = db1550_nand_parts,
180 .dev_ready = au1550_nand_device_ready,
181 .cmd_ctrl = au1550_nand_cmd_ctrl,
185 static struct resource db1550_nand_res[] = {
189 .flags = IORESOURCE_MEM,
193 static struct platform_device db1550_nand_dev = {
195 .num_resources = ARRAY_SIZE(db1550_nand_res),
196 .resource = db1550_nand_res,
199 .platform_data = &db1550_nand_platdata,
203 static struct au1550nd_platdata pb1550_nand_pd = {
204 .parts = db1550_nand_parts,
205 .num_parts = ARRAY_SIZE(db1550_nand_parts),
206 .devwidth = 0, /* x8 NAND default, needs fixing up */
209 static struct platform_device pb1550_nand_dev = {
210 .name = "au1550-nand",
212 .resource = db1550_nand_res,
213 .num_resources = ARRAY_SIZE(db1550_nand_res),
215 .platform_data = &pb1550_nand_pd,
219 static void __init pb1550_nand_setup(void)
221 int boot_swapboot = (alchemy_rdsmem(AU1000_MEM_STSTAT) & (0x7 << 1)) |
222 ((bcsr_read(BCSR_STATUS) >> 6) & 0x1);
224 gpio_direction_input(206); /* de-assert NAND CS# */
225 switch (boot_swapboot) {
226 case 0: case 2: case 8: case 0xC: case 0xD:
228 pb1550_nand_pd.devwidth = 1;
230 case 1: case 3: case 9: case 0xE: case 0xF:
231 /* x8 NAND, already set up */
232 platform_device_register(&pb1550_nand_dev);
236 /**********************************************************************/
238 static struct resource au1550_psc0_res[] = {
240 .start = AU1550_PSC0_PHYS_ADDR,
241 .end = AU1550_PSC0_PHYS_ADDR + 0xfff,
242 .flags = IORESOURCE_MEM,
245 .start = AU1550_PSC0_INT,
246 .end = AU1550_PSC0_INT,
247 .flags = IORESOURCE_IRQ,
250 .start = AU1550_DSCR_CMD0_PSC0_TX,
251 .end = AU1550_DSCR_CMD0_PSC0_TX,
252 .flags = IORESOURCE_DMA,
255 .start = AU1550_DSCR_CMD0_PSC0_RX,
256 .end = AU1550_DSCR_CMD0_PSC0_RX,
257 .flags = IORESOURCE_DMA,
261 static void db1550_spi_cs_en(struct au1550_spi_info *spi, int cs, int pol)
264 bcsr_mod(BCSR_BOARD, 0, BCSR_BOARD_SPISEL);
266 bcsr_mod(BCSR_BOARD, BCSR_BOARD_SPISEL, 0);
269 static struct au1550_spi_info db1550_spi_platdata = {
270 .mainclk_hz = 48000000, /* PSC0 clock: max. 2.4MHz SPI clk */
272 .activate_cs = db1550_spi_cs_en,
276 static struct platform_device db1550_spi_dev = {
278 .dma_mask = &au1550_all_dmamask,
279 .coherent_dma_mask = DMA_BIT_MASK(32),
280 .platform_data = &db1550_spi_platdata,
282 .name = "au1550-spi",
283 .id = 0, /* bus number */
284 .num_resources = ARRAY_SIZE(au1550_psc0_res),
285 .resource = au1550_psc0_res,
288 /**********************************************************************/
290 static struct resource au1550_psc1_res[] = {
292 .start = AU1550_PSC1_PHYS_ADDR,
293 .end = AU1550_PSC1_PHYS_ADDR + 0xfff,
294 .flags = IORESOURCE_MEM,
297 .start = AU1550_PSC1_INT,
298 .end = AU1550_PSC1_INT,
299 .flags = IORESOURCE_IRQ,
302 .start = AU1550_DSCR_CMD0_PSC1_TX,
303 .end = AU1550_DSCR_CMD0_PSC1_TX,
304 .flags = IORESOURCE_DMA,
307 .start = AU1550_DSCR_CMD0_PSC1_RX,
308 .end = AU1550_DSCR_CMD0_PSC1_RX,
309 .flags = IORESOURCE_DMA,
313 static struct platform_device db1550_ac97_dev = {
314 .name = "au1xpsc_ac97",
315 .id = 1, /* PSC ID */
316 .num_resources = ARRAY_SIZE(au1550_psc1_res),
317 .resource = au1550_psc1_res,
321 static struct resource au1550_psc2_res[] = {
323 .start = AU1550_PSC2_PHYS_ADDR,
324 .end = AU1550_PSC2_PHYS_ADDR + 0xfff,
325 .flags = IORESOURCE_MEM,
328 .start = AU1550_PSC2_INT,
329 .end = AU1550_PSC2_INT,
330 .flags = IORESOURCE_IRQ,
333 .start = AU1550_DSCR_CMD0_PSC2_TX,
334 .end = AU1550_DSCR_CMD0_PSC2_TX,
335 .flags = IORESOURCE_DMA,
338 .start = AU1550_DSCR_CMD0_PSC2_RX,
339 .end = AU1550_DSCR_CMD0_PSC2_RX,
340 .flags = IORESOURCE_DMA,
344 static struct platform_device db1550_i2c_dev = {
345 .name = "au1xpsc_smbus",
346 .id = 0, /* bus number */
347 .num_resources = ARRAY_SIZE(au1550_psc2_res),
348 .resource = au1550_psc2_res,
351 /**********************************************************************/
353 static struct resource au1550_psc3_res[] = {
355 .start = AU1550_PSC3_PHYS_ADDR,
356 .end = AU1550_PSC3_PHYS_ADDR + 0xfff,
357 .flags = IORESOURCE_MEM,
360 .start = AU1550_PSC3_INT,
361 .end = AU1550_PSC3_INT,
362 .flags = IORESOURCE_IRQ,
365 .start = AU1550_DSCR_CMD0_PSC3_TX,
366 .end = AU1550_DSCR_CMD0_PSC3_TX,
367 .flags = IORESOURCE_DMA,
370 .start = AU1550_DSCR_CMD0_PSC3_RX,
371 .end = AU1550_DSCR_CMD0_PSC3_RX,
372 .flags = IORESOURCE_DMA,
376 static struct platform_device db1550_i2s_dev = {
377 .name = "au1xpsc_i2s",
378 .id = 3, /* PSC ID */
379 .num_resources = ARRAY_SIZE(au1550_psc3_res),
380 .resource = au1550_psc3_res,
383 /**********************************************************************/
385 static struct platform_device db1550_stac_dev = {
386 .name = "ac97-codec",
387 .id = 1, /* on PSC1 */
390 static struct platform_device db1550_ac97dma_dev = {
391 .name = "au1xpsc-pcm",
392 .id = 1, /* on PSC3 */
395 static struct platform_device db1550_i2sdma_dev = {
396 .name = "au1xpsc-pcm",
397 .id = 3, /* on PSC3 */
400 static struct platform_device db1550_sndac97_dev = {
401 .name = "db1550-ac97",
403 .dma_mask = &au1550_all_dmamask,
404 .coherent_dma_mask = DMA_BIT_MASK(32),
408 static struct platform_device db1550_sndi2s_dev = {
409 .name = "db1550-i2s",
411 .dma_mask = &au1550_all_dmamask,
412 .coherent_dma_mask = DMA_BIT_MASK(32),
416 /**********************************************************************/
418 static int db1550_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
420 if ((slot < 11) || (slot > 13) || pin == 0)
423 return (pin == 1) ? AU1550_PCI_INTC : 0xff;
426 case 1: return AU1550_PCI_INTB;
427 case 2: return AU1550_PCI_INTC;
428 case 3: return AU1550_PCI_INTD;
429 case 4: return AU1550_PCI_INTA;
434 case 1: return AU1550_PCI_INTA;
435 case 2: return AU1550_PCI_INTB;
436 case 3: return AU1550_PCI_INTC;
437 case 4: return AU1550_PCI_INTD;
443 static int pb1550_map_pci_irq(const struct pci_dev *d, u8 slot, u8 pin)
445 if ((slot < 12) || (slot > 13) || pin == 0)
449 case 1: return AU1500_PCI_INTB;
450 case 2: return AU1500_PCI_INTC;
451 case 3: return AU1500_PCI_INTD;
452 case 4: return AU1500_PCI_INTA;
457 case 1: return AU1500_PCI_INTA;
458 case 2: return AU1500_PCI_INTB;
459 case 3: return AU1500_PCI_INTC;
460 case 4: return AU1500_PCI_INTD;
466 static struct resource alchemy_pci_host_res[] = {
468 .start = AU1500_PCI_PHYS_ADDR,
469 .end = AU1500_PCI_PHYS_ADDR + 0xfff,
470 .flags = IORESOURCE_MEM,
474 static struct alchemy_pci_platdata db1550_pci_pd = {
475 .board_map_irq = db1550_map_pci_irq,
478 static struct platform_device db1550_pci_host_dev = {
479 .dev.platform_data = &db1550_pci_pd,
480 .name = "alchemy-pci",
482 .num_resources = ARRAY_SIZE(alchemy_pci_host_res),
483 .resource = alchemy_pci_host_res,
486 /**********************************************************************/
488 static struct platform_device *db1550_devs[] __initdata = {
500 /* must be arch_initcall; MIPS PCI scans busses in a subsys_initcall */
501 int __init db1550_pci_setup(int id)
504 db1550_pci_pd.board_map_irq = pb1550_map_pci_irq;
505 return platform_device_register(&db1550_pci_host_dev);
508 static void __init db1550_devices(void)
510 alchemy_gpio_direction_output(203, 0); /* red led on */
512 irq_set_irq_type(AU1550_GPIO0_INT, IRQ_TYPE_EDGE_BOTH); /* CD0# */
513 irq_set_irq_type(AU1550_GPIO1_INT, IRQ_TYPE_EDGE_BOTH); /* CD1# */
514 irq_set_irq_type(AU1550_GPIO3_INT, IRQ_TYPE_LEVEL_LOW); /* CARD0# */
515 irq_set_irq_type(AU1550_GPIO5_INT, IRQ_TYPE_LEVEL_LOW); /* CARD1# */
516 irq_set_irq_type(AU1550_GPIO21_INT, IRQ_TYPE_LEVEL_LOW); /* STSCHG0# */
517 irq_set_irq_type(AU1550_GPIO22_INT, IRQ_TYPE_LEVEL_LOW); /* STSCHG1# */
519 db1x_register_pcmcia_socket(
520 AU1000_PCMCIA_ATTR_PHYS_ADDR,
521 AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
522 AU1000_PCMCIA_MEM_PHYS_ADDR,
523 AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
524 AU1000_PCMCIA_IO_PHYS_ADDR,
525 AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
527 /*AU1550_GPIO21_INT*/0, 0, 0);
529 db1x_register_pcmcia_socket(
530 AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004000000,
531 AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x004400000 - 1,
532 AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004000000,
533 AU1000_PCMCIA_MEM_PHYS_ADDR + 0x004400000 - 1,
534 AU1000_PCMCIA_IO_PHYS_ADDR + 0x004000000,
535 AU1000_PCMCIA_IO_PHYS_ADDR + 0x004010000 - 1,
537 /*AU1550_GPIO22_INT*/0, 0, 1);
539 platform_device_register(&db1550_nand_dev);
541 alchemy_gpio_direction_output(202, 0); /* green led on */
544 static void __init pb1550_devices(void)
546 irq_set_irq_type(AU1550_GPIO0_INT, IRQ_TYPE_LEVEL_LOW);
547 irq_set_irq_type(AU1550_GPIO1_INT, IRQ_TYPE_LEVEL_LOW);
548 irq_set_irq_type(AU1550_GPIO201_205_INT, IRQ_TYPE_LEVEL_HIGH);
550 /* enable both PCMCIA card irqs in the shared line */
551 alchemy_gpio2_enable_int(201); /* socket 0 card irq */
552 alchemy_gpio2_enable_int(202); /* socket 1 card irq */
554 /* Pb1550, like all others, also has statuschange irqs; however they're
555 * wired up on one of the Au1550's shared GPIO201_205 line, which also
556 * services the PCMCIA card interrupts. So we ignore statuschange and
557 * use the GPIO201_205 exclusively for card interrupts, since a) pcmcia
558 * drivers are used to shared irqs and b) statuschange isn't really use-
561 db1x_register_pcmcia_socket(
562 AU1000_PCMCIA_ATTR_PHYS_ADDR,
563 AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x000400000 - 1,
564 AU1000_PCMCIA_MEM_PHYS_ADDR,
565 AU1000_PCMCIA_MEM_PHYS_ADDR + 0x000400000 - 1,
566 AU1000_PCMCIA_IO_PHYS_ADDR,
567 AU1000_PCMCIA_IO_PHYS_ADDR + 0x000010000 - 1,
568 AU1550_GPIO201_205_INT, AU1550_GPIO0_INT, 0, 0, 0);
570 db1x_register_pcmcia_socket(
571 AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008000000,
572 AU1000_PCMCIA_ATTR_PHYS_ADDR + 0x008400000 - 1,
573 AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008000000,
574 AU1000_PCMCIA_MEM_PHYS_ADDR + 0x008400000 - 1,
575 AU1000_PCMCIA_IO_PHYS_ADDR + 0x008000000,
576 AU1000_PCMCIA_IO_PHYS_ADDR + 0x008010000 - 1,
577 AU1550_GPIO201_205_INT, AU1550_GPIO1_INT, 0, 0, 1);
582 int __init db1550_dev_setup(void)
587 id = (BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI)) != BCSR_WHOAMI_DB1550);
589 i2c_register_board_info(0, db1550_i2c_devs,
590 ARRAY_SIZE(db1550_i2c_devs));
591 spi_register_board_info(db1550_spi_devs,
592 ARRAY_SIZE(db1550_i2c_devs));
594 c = clk_get(NULL, "psc0_intclk");
596 clk_set_rate(c, 50000000);
597 clk_prepare_enable(c);
600 c = clk_get(NULL, "psc2_intclk");
602 clk_set_rate(c, db1550_spi_platdata.mainclk_hz);
603 clk_prepare_enable(c);
607 /* Audio PSC clock is supplied by codecs (PSC1, 3) FIXME: platdata!! */
608 __raw_writel(PSC_SEL_CLK_SERCLK,
609 (void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR) + PSC_SEL_OFFSET);
611 __raw_writel(PSC_SEL_CLK_SERCLK,
612 (void __iomem *)KSEG1ADDR(AU1550_PSC3_PHYS_ADDR) + PSC_SEL_OFFSET);
614 /* SPI/I2C use internally supplied 50MHz source */
615 __raw_writel(PSC_SEL_CLK_INTCLK,
616 (void __iomem *)KSEG1ADDR(AU1550_PSC0_PHYS_ADDR) + PSC_SEL_OFFSET);
618 __raw_writel(PSC_SEL_CLK_INTCLK,
619 (void __iomem *)KSEG1ADDR(AU1550_PSC2_PHYS_ADDR) + PSC_SEL_OFFSET);
622 id ? pb1550_devices() : db1550_devices();
624 swapped = bcsr_read(BCSR_STATUS) &
625 (id ? BCSR_STATUS_PB1550_SWAPBOOT : BCSR_STATUS_DB1000_SWAPBOOT);
626 db1x_register_norflash(128 << 20, 4, swapped);
628 return platform_add_devices(db1550_devs, ARRAY_SIZE(db1550_devs));