1 // SPDX-License-Identifier: GPL-2.0+
3 * dts file for Xilinx ZynqMP ZCU106
5 * (C) Copyright 2016, Xilinx, Inc.
7 * Michal Simek <michal.simek@xilinx.com>
12 #include "zynqmp.dtsi"
13 #include "zynqmp-clk.dtsi"
14 #include <dt-bindings/input/input.h>
15 #include <dt-bindings/gpio/gpio.h>
18 model = "ZynqMP ZCU106 RevA";
19 compatible = "xlnx,zynqmp-zcu106-revA", "xlnx,zynqmp-zcu106", "xlnx,zynqmp";
33 bootargs = "earlycon";
34 stdout-path = "serial0:115200n8";
38 device_type = "memory";
39 reg = <0x0 0x0 0x0 0x80000000>, <0x8 0x00000000 0x0 0x80000000>;
43 compatible = "gpio-keys";
47 gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
48 linux,code = <KEY_DOWN>;
55 compatible = "gpio-leds";
58 gpios = <&gpio 23 GPIO_ACTIVE_HIGH>;
59 linux,default-trigger = "heartbeat";
72 /* fpd_dma clk 667MHz, lpd_dma 500MHz */
107 phy-handle = <&phy0>;
108 phy-mode = "rgmii-id";
111 ti,rx-internal-delay = <0x8>;
112 ti,tx-internal-delay = <0xa>;
113 ti,fifo-depth = <0x1>;
123 clock-frequency = <400000>;
125 tca6416_u97: gpio@20 {
126 compatible = "ti,tca6416";
128 gpio-controller; /* interrupt not connected */
133 * 0 - SFP_SI5328_INT_ALM
134 * 1 - HDMI_SI5328_INT_ALM
135 * 5 - IIC_MUX_RESET_B
136 * 6 - GEM3_EXP_RESET_B
137 * 10 - FMC_HPC0_PRSNT_M2C_B
138 * 11 - FMC_HPC1_PRSNT_M2C_B
139 * 2-4, 7, 12-17 - not connected
143 tca6416_u61: gpio@21 {
144 compatible = "ti,tca6416";
155 * 4 - MIO26_PMU_INPUT_LS
158 * 7 - MAXIM_PMBUS_ALERT
159 * 10 - PL_DDR4_VTERM_EN
160 * 11 - PL_DDR4_VPP_2V5_EN
161 * 12 - PS_DIMM_VDDQ_TO_PSVCCO_ON
162 * 13 - PS_DIMM_SUSPEND_EN
163 * 14 - PS_DDR4_VTERM_EN
164 * 15 - PS_DDR4_VPP_2V5_EN
165 * 16 - 17 - not connected
169 i2c-mux@75 { /* u60 */
170 compatible = "nxp,pca9544";
171 #address-cells = <1>;
175 #address-cells = <1>;
179 ina226@40 { /* u76 */
180 compatible = "ti,ina226";
182 shunt-resistor = <5000>;
184 ina226@41 { /* u77 */
185 compatible = "ti,ina226";
187 shunt-resistor = <5000>;
189 ina226@42 { /* u78 */
190 compatible = "ti,ina226";
192 shunt-resistor = <5000>;
194 ina226@43 { /* u87 */
195 compatible = "ti,ina226";
197 shunt-resistor = <5000>;
199 ina226@44 { /* u85 */
200 compatible = "ti,ina226";
202 shunt-resistor = <5000>;
204 ina226@45 { /* u86 */
205 compatible = "ti,ina226";
207 shunt-resistor = <5000>;
209 ina226@46 { /* u93 */
210 compatible = "ti,ina226";
212 shunt-resistor = <5000>;
214 ina226@47 { /* u88 */
215 compatible = "ti,ina226";
217 shunt-resistor = <5000>;
219 ina226@4a { /* u15 */
220 compatible = "ti,ina226";
222 shunt-resistor = <5000>;
224 ina226@4b { /* u92 */
225 compatible = "ti,ina226";
227 shunt-resistor = <5000>;
231 #address-cells = <1>;
235 ina226@40 { /* u79 */
236 compatible = "ti,ina226";
238 shunt-resistor = <2000>;
240 ina226@41 { /* u81 */
241 compatible = "ti,ina226";
243 shunt-resistor = <5000>;
245 ina226@42 { /* u80 */
246 compatible = "ti,ina226";
248 shunt-resistor = <5000>;
250 ina226@43 { /* u84 */
251 compatible = "ti,ina226";
253 shunt-resistor = <5000>;
255 ina226@44 { /* u16 */
256 compatible = "ti,ina226";
258 shunt-resistor = <5000>;
260 ina226@45 { /* u65 */
261 compatible = "ti,ina226";
263 shunt-resistor = <5000>;
265 ina226@46 { /* u74 */
266 compatible = "ti,ina226";
268 shunt-resistor = <5000>;
270 ina226@47 { /* u75 */
271 compatible = "ti,ina226";
273 shunt-resistor = <5000>;
277 #address-cells = <1>;
280 /* MAXIM_PMBUS - 00 */
281 max15301@a { /* u46 */
282 compatible = "maxim,max15301";
285 max15303@b { /* u4 */
286 compatible = "maxim,max15303";
289 max15303@10 { /* u13 */
290 compatible = "maxim,max15303";
293 max15301@13 { /* u47 */
294 compatible = "maxim,max15301";
297 max15303@14 { /* u7 */
298 compatible = "maxim,max15303";
301 max15303@15 { /* u6 */
302 compatible = "maxim,max15303";
305 max15303@16 { /* u10 */
306 compatible = "maxim,max15303";
309 max15303@17 { /* u9 */
310 compatible = "maxim,max15303";
313 max15301@18 { /* u63 */
314 compatible = "maxim,max15301";
317 max15303@1a { /* u49 */
318 compatible = "maxim,max15303";
321 max15303@1b { /* u8 */
322 compatible = "maxim,max15303";
325 max15303@1d { /* u18 */
326 compatible = "maxim,max15303";
330 max20751@72 { /* u95 */
331 compatible = "maxim,max20751";
334 max20751@73 { /* u96 */
335 compatible = "maxim,max20751";
339 /* Bus 3 is not connected */
345 clock-frequency = <400000>;
347 /* PL i2c via PCA9306 - u45 */
348 i2c-mux@74 { /* u34 */
349 compatible = "nxp,pca9548";
350 #address-cells = <1>;
354 #address-cells = <1>;
358 * IIC_EEPROM 1kB memory which uses 256B blocks
359 * where every block has different address.
360 * 0 - 256B address 0x54
361 * 256B - 512B address 0x55
362 * 512B - 768B address 0x56
363 * 768B - 1024B address 0x57
365 eeprom: eeprom@54 { /* u23 */
366 compatible = "atmel,24c08";
371 #address-cells = <1>;
374 si5341: clock-generator@36 { /* SI5341 - u69 */
380 #address-cells = <1>;
383 si570_1: clock-generator@5d { /* USER SI570 - u42 */
385 compatible = "silabs,si570";
387 temperature-stability = <50>;
388 factory-fout = <300000000>;
389 clock-frequency = <300000000>;
393 #address-cells = <1>;
396 si570_2: clock-generator@5d { /* USER MGT SI570 - u56 */
398 compatible = "silabs,si570";
400 temperature-stability = <50>; /* copy from zc702 */
401 factory-fout = <156250000>;
402 clock-frequency = <148500000>;
406 #address-cells = <1>;
409 si5328: clock-generator@69 {/* SI5328 - u20 */
414 #address-cells = <1>;
416 reg = <5>; /* FAN controller */
417 temp@4c {/* lm96163 - u128 */
418 compatible = "national,lm96163";
422 /* 6 - 7 unconnected */
426 compatible = "nxp,pca9548"; /* u135 */
427 #address-cells = <1>;
432 #address-cells = <1>;
438 #address-cells = <1>;
444 #address-cells = <1>;
450 #address-cells = <1>;
456 #address-cells = <1>;
462 #address-cells = <1>;
468 #address-cells = <1>;
474 #address-cells = <1>;
488 /* SATA OOB timing settings */
489 ceva,p0-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
490 ceva,p0-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
491 ceva,p0-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
492 ceva,p0-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
493 ceva,p1-cominit-params = /bits/ 8 <0x18 0x40 0x18 0x28>;
494 ceva,p1-comwake-params = /bits/ 8 <0x06 0x14 0x08 0x0E>;
495 ceva,p1-burst-params = /bits/ 8 <0x13 0x08 0x4A 0x06>;
496 ceva,p1-retry-params = /bits/ 16 <0x96A4 0x3FFC>;
499 /* SD1 with level shifter */
513 /* ULPI SMSC USB3320 */