arch/arm64/boot/dts/qcom/sm8450-hdk.dts

   1 // SPDX-License-Identifier: BSD-3-Clause
   2 /*
   3  * Copyright (c) 2022, Linaro Limited
   4  */
   5
   6 /dts-v1/;
   7
   8 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
   9 #include <dt-bindings/iio/qcom,spmi-adc7-pm8350.h>
  10 #include <dt-bindings/iio/qcom,spmi-adc7-pm8350b.h>
  11 #include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h>
  12 #include <dt-bindings/iio/qcom,spmi-adc7-pmr735a.h>
  13 #include <dt-bindings/sound/qcom,q6dsp-lpass-ports.h>
  14 #include "sm8450.dtsi"
  15 #include "pm8350.dtsi"
  16 #include "pm8350b.dtsi"
  17 #include "pm8350c.dtsi"
  18 #include "pm8450.dtsi"
  19 #include "pmk8350.dtsi"
  20 #include "pmr735a.dtsi"
  21
  22 / {
  23         model = "Qualcomm Technologies, Inc. SM8450 HDK";
  24         compatible = "qcom,sm8450-hdk", "qcom,sm8450";
  25         chassis-type = "embedded";
  26
  27         aliases {
  28                 serial0 = &uart7;
  29         };
  30
  31         wcd938x: audio-codec {
  32                 compatible = "qcom,wcd9385-codec";
  33
  34                 pinctrl-names = "default";
  35                 pinctrl-0 = <&wcd_default>;
  36
  37                 qcom,micbias1-microvolt = <1800000>;
  38                 qcom,micbias2-microvolt = <1800000>;
  39                 qcom,micbias3-microvolt = <1800000>;
  40                 qcom,micbias4-microvolt = <1800000>;
  41                 qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
  42                 qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
  43                 qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
  44                 qcom,rx-device = <&wcd_rx>;
  45                 qcom,tx-device = <&wcd_tx>;
  46
  47                 reset-gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
  48
  49                 vdd-buck-supply = <&vreg_s10b_1p8>;
  50                 vdd-rxtx-supply = <&vreg_s10b_1p8>;
  51                 vdd-io-supply = <&vreg_s10b_1p8>;
  52                 vdd-mic-bias-supply = <&vreg_bob>;
  53
  54                 #sound-dai-cells = <1>;
  55         };
  56
  57         chosen {
  58                 stdout-path = "serial0:115200n8";
  59         };
  60
  61         hdmi-out {
  62                 compatible = "hdmi-connector";
  63                 type = "a";
  64
  65                 port {
  66                         hdmi_connector_out: endpoint {
  67                                 remote-endpoint = <&lt9611_out>;
  68                         };
  69                 };
  70         };
  71
  72         lt9611_1v2: lt9611-vdd12-regulator {
  73                 compatible = "regulator-fixed";
  74                 regulator-name = "LT9611_1V2";
  75
  76                 vin-supply = <&vph_pwr>;
  77                 regulator-min-microvolt = <1200000>;
  78                 regulator-max-microvolt = <1200000>;
  79                 gpio = <&tlmm 9 GPIO_ACTIVE_HIGH>;
  80                 enable-active-high;
  81         };
  82
  83         lt9611_3v3: lt9611-3v3-regulator {
  84                 compatible = "regulator-fixed";
  85                 regulator-name = "LT9611_3V3";
  86
  87                 vin-supply = <&vreg_bob>;
  88                 gpio = <&tlmm 109 GPIO_ACTIVE_HIGH>;
  89                 regulator-min-microvolt = <3300000>;
  90                 regulator-max-microvolt = <3300000>;
  91                 enable-active-high;
  92         };
  93
  94         pmic-glink {
  95                 compatible = "qcom,sm8450-pmic-glink", "qcom,pmic-glink";
  96                 #address-cells = <1>;
  97                 #size-cells = <0>;
  98
  99                 connector@0 {
 100                         compatible = "usb-c-connector";
 101                         reg = <0>;
 102                         power-role = "dual";
 103                         data-role = "dual";
 104
 105                         ports {
 106                                 #address-cells = <1>;
 107                                 #size-cells = <0>;
 108
 109                                 port@0 {
 110                                         reg = <0>;
 111
 112                                         pmic_glink_hs_in: endpoint {
 113                                                 remote-endpoint = <&usb_1_dwc3_hs>;
 114                                         };
 115                                 };
 116
 117                                 port@1 {
 118                                         reg = <1>;
 119
 120                                         pmic_glink_ss_in: endpoint {
 121                                                 remote-endpoint = <&usb_1_qmpphy_out>;
 122                                         };
 123                                 };
 124
 125                                 port@2 {
 126                                         reg = <2>;
 127
 128                                         pmic_glink_sbu: endpoint {
 129                                                 remote-endpoint = <&fsa4480_sbu_mux>;
 130                                         };
 131                                 };
 132
 133                         };
 134                 };
 135         };
 136
 137         thermal-zones {
 138                 camera-thermal {
 139                         polling-delay-passive = <250>;
 140                         polling-delay = <0>;
 141                         thermal-sensors = <&pmk8350_adc_tm 2>;
 142
 143                         trips {
 144                                 active-config0 {
 145                                         temperature = <75000>;
 146                                         hysteresis = <4000>;
 147                                         type = "passive";
 148                                 };
 149                         };
 150                 };
 151
 152                 rear-tof-thermal {
 153                         polling-delay-passive = <250>;
 154                         polling-delay = <0>;
 155                         thermal-sensors = <&pmk8350_adc_tm 5>;
 156
 157                         trips {
 158                                 active-config0 {
 159                                         temperature = <75000>;
 160                                         hysteresis = <4000>;
 161                                         type = "passive";
 162                                 };
 163                         };
 164                 };
 165
 166                 skin-msm-thermal {
 167                         polling-delay-passive = <250>;
 168                         polling-delay = <0>;
 169                         thermal-sensors = <&pmk8350_adc_tm 1>;
 170
 171                         trips {
 172                                 active-config0 {
 173                                         temperature = <75000>;
 174                                         hysteresis = <4000>;
 175                                         type = "passive";
 176                                 };
 177                         };
 178                 };
 179
 180                 therm1-thermal {
 181                         polling-delay-passive = <250>;
 182                         polling-delay = <0>;
 183                         thermal-sensors = <&pmk8350_adc_tm 3>;
 184
 185                         trips {
 186                                 active-config0 {
 187                                         temperature = <75000>;
 188                                         hysteresis = <4000>;
 189                                         type = "passive";
 190                                 };
 191                         };
 192                 };
 193
 194                 therm2-thermal {
 195                         polling-delay-passive = <250>;
 196                         polling-delay = <0>;
 197                         thermal-sensors = <&pmk8350_adc_tm 6>;
 198
 199                         trips {
 200                                 active-config0 {
 201                                         temperature = <75000>;
 202                                         hysteresis = <4000>;
 203                                         type = "passive";
 204                                 };
 205                         };
 206                 };
 207
 208                 usb-conn-thermal {
 209                         polling-delay-passive = <250>;
 210                         polling-delay = <0>;
 211                         thermal-sensors = <&pmk8350_adc_tm 7>;
 212
 213                         trips {
 214                                 active-config0 {
 215                                         temperature = <75000>;
 216                                         hysteresis = <4000>;
 217                                         type = "passive";
 218                                 };
 219                         };
 220                 };
 221
 222                 wide-rfc-thermal {
 223                         polling-delay-passive = <250>;
 224                         polling-delay = <0>;
 225                         thermal-sensors = <&pmk8350_adc_tm 4>;
 226
 227                         trips {
 228                                 active-config0 {
 229                                         temperature = <75000>;
 230                                         hysteresis = <4000>;
 231                                         type = "passive";
 232                                 };
 233                         };
 234                 };
 235
 236                 xo-thermal {
 237                         polling-delay-passive = <0>;
 238                         polling-delay = <0>;
 239                         thermal-sensors = <&pmk8350_adc_tm 0>;
 240
 241                         trips {
 242                                 active-config0 {
 243                                         temperature = <50000>;
 244                                         hysteresis = <4000>;
 245                                         type = "passive";
 246                                 };
 247                         };
 248                 };
 249         };
 250
 251         vph_pwr: vph-pwr-regulator {
 252                 compatible = "regulator-fixed";
 253                 regulator-name = "vph_pwr";
 254                 regulator-min-microvolt = <3700000>;
 255                 regulator-max-microvolt = <3700000>;
 256
 257                 regulator-always-on;
 258                 regulator-boot-on;
 259         };
 260 };
 261
 262 &apps_rsc {
 263         regulators-0 {
 264                 compatible = "qcom,pm8350-rpmh-regulators";
 265                 qcom,pmic-id = "b";
 266
 267                 vdd-s1-supply = <&vph_pwr>;
 268                 vdd-s2-supply = <&vph_pwr>;
 269                 vdd-s3-supply = <&vph_pwr>;
 270                 vdd-s4-supply = <&vph_pwr>;
 271                 vdd-s5-supply = <&vph_pwr>;
 272                 vdd-s6-supply = <&vph_pwr>;
 273                 vdd-s7-supply = <&vph_pwr>;
 274                 vdd-s8-supply = <&vph_pwr>;
 275                 vdd-s9-supply = <&vph_pwr>;
 276                 vdd-s10-supply = <&vph_pwr>;
 277                 vdd-s11-supply = <&vph_pwr>;
 278                 vdd-s12-supply = <&vph_pwr>;
 279
 280                 vdd-l1-l4-supply = <&vreg_s11b_0p95>;
 281                 vdd-l2-l7-supply = <&vreg_bob>;
 282                 vdd-l3-l5-supply = <&vreg_bob>;
 283                 vdd-l6-l9-l10-supply = <&vreg_s12b_1p25>;
 284                 vdd-l8-supply = <&vreg_s2h_0p95>;
 285
 286                 vreg_s10b_1p8: smps10 {
 287                         regulator-name = "vreg_s10b_1p8";
 288                         regulator-min-microvolt = <1800000>;
 289                         regulator-max-microvolt = <1800000>;
 290                 };
 291
 292                 vreg_s11b_0p95: smps11 {
 293                         regulator-name = "vreg_s11b_0p95";
 294                         regulator-min-microvolt = <966000>;
 295                         regulator-max-microvolt = <1104000>;
 296                 };
 297
 298                 vreg_s12b_1p25: smps12 {
 299                         regulator-name = "vreg_s12b_1p25";
 300                         regulator-min-microvolt = <1350000>;
 301                         regulator-max-microvolt = <1400000>;
 302                 };
 303
 304                 vreg_l1b_0p91: ldo1 {
 305                         regulator-name = "vreg_l1b_0p91";
 306                         regulator-min-microvolt = <912000>;
 307                         regulator-max-microvolt = <920000>;
 308                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 309                 };
 310
 311                 vreg_l2b_3p07: ldo2 {
 312                         regulator-name = "vreg_l2b_3p07";
 313                         regulator-min-microvolt = <3072000>;
 314                         regulator-max-microvolt = <3072000>;
 315                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 316                 };
 317
 318                 vreg_l3b_0p9: ldo3 {
 319                         regulator-name = "vreg_l3b_0p9";
 320                         regulator-min-microvolt = <904000>;
 321                         regulator-max-microvolt = <904000>;
 322                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 323                 };
 324
 325                 vreg_l5b_0p88: ldo5 {
 326                         regulator-name = "vreg_l5b_0p88";
 327                         regulator-min-microvolt = <880000>;
 328                         regulator-max-microvolt = <888000>;
 329                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 330                 };
 331
 332                 vreg_l6b_1p2: ldo6 {
 333                         regulator-name = "vreg_l6b_1p2";
 334                         regulator-min-microvolt = <1200000>;
 335                         regulator-max-microvolt = <1200000>;
 336                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 337                 };
 338
 339                 vreg_l7b_2p5: ldo7 {
 340                         regulator-name = "vreg_l7b_2p5";
 341                         regulator-min-microvolt = <2504000>;
 342                         regulator-max-microvolt = <2504000>;
 343                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 344                 };
 345
 346                 vreg_l9b_1p2: ldo9 {
 347                         regulator-name = "vreg_l9b_1p2";
 348                         regulator-min-microvolt = <1200000>;
 349                         regulator-max-microvolt = <1200000>;
 350                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 351                 };
 352         };
 353
 354         regulators-1 {
 355                 compatible = "qcom,pm8350c-rpmh-regulators";
 356                 qcom,pmic-id = "c";
 357
 358                 vdd-s1-supply = <&vph_pwr>;
 359                 vdd-s2-supply = <&vph_pwr>;
 360                 vdd-s3-supply = <&vph_pwr>;
 361                 vdd-s4-supply = <&vph_pwr>;
 362                 vdd-s5-supply = <&vph_pwr>;
 363                 vdd-s6-supply = <&vph_pwr>;
 364                 vdd-s7-supply = <&vph_pwr>;
 365                 vdd-s8-supply = <&vph_pwr>;
 366                 vdd-s9-supply = <&vph_pwr>;
 367                 vdd-s10-supply = <&vph_pwr>;
 368
 369                 vdd-l1-l12-supply = <&vreg_bob>;
 370                 vdd-l2-l8-supply = <&vreg_bob>;
 371                 vdd-l3-l4-l5-l7-l13-supply = <&vreg_bob>;
 372                 vdd-l6-l9-l11-supply = <&vreg_bob>;
 373                 vdd-l10-supply = <&vreg_s12b_1p25>;
 374
 375                 vdd-bob-supply = <&vph_pwr>;
 376
 377                 vreg_s1c_1p86: smps1 {
 378                         regulator-name = "vreg_s1c_1p86";
 379                         regulator-min-microvolt = <1800000>;
 380                         regulator-max-microvolt = <2024000>;
 381                 };
 382
 383                 vreg_s10c_1p05: smps10 {
 384                         regulator-name = "vreg_s10c_1p05";
 385                         regulator-min-microvolt = <1000000>;
 386                         regulator-max-microvolt = <1100000>;
 387                 };
 388
 389                 vreg_bob: bob {
 390                         regulator-name = "vreg_bob";
 391                         regulator-min-microvolt = <3008000>;
 392                         regulator-max-microvolt = <3960000>;
 393                         regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
 394                 };
 395
 396                 vreg_l1c_1p8: ldo1 {
 397                         regulator-name = "vreg_l1c_1p8";
 398                         regulator-min-microvolt = <1800000>;
 399                         regulator-max-microvolt = <1800000>;
 400                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 401                 };
 402
 403                 vreg_l3c_3p0: ldo3 {
 404                         regulator-name = "vreg_l3c_3p0";
 405                         regulator-min-microvolt = <3296000>;
 406                         regulator-max-microvolt = <3304000>;
 407                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 408                 };
 409
 410                 vreg_l4c_1p8: ldo4 {
 411                         regulator-name = "vreg_l4c_1p8";
 412                         regulator-min-microvolt = <1704000>;
 413                         regulator-max-microvolt = <3000000>;
 414                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 415                 };
 416
 417                 vreg_l5c_1p8: ldo5 {
 418                         regulator-name = "vreg_l5c_1p8";
 419                         regulator-min-microvolt = <1704000>;
 420                         regulator-max-microvolt = <3000000>;
 421                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 422                 };
 423
 424                 vreg_l6c_1p8: ldo6 {
 425                         regulator-name = "vreg_l6c_1p8";
 426                         regulator-min-microvolt = <1800000>;
 427                         regulator-max-microvolt = <3008000>;
 428                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 429                 };
 430
 431                 vreg_l7c_3p0: ldo7 {
 432                         regulator-name = "vreg_l7c_3p0";
 433                         regulator-min-microvolt = <3008000>;
 434                         regulator-max-microvolt = <3008000>;
 435                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 436                 };
 437
 438                 vreg_l8c_1p8: ldo8 {
 439                         regulator-name = "vreg_l8c_1p8";
 440                         regulator-min-microvolt = <1800000>;
 441                         regulator-max-microvolt = <1800000>;
 442                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 443                 };
 444
 445                 vreg_l9c_2p96: ldo9 {
 446                         regulator-name = "vreg_l9c_2p96";
 447                         regulator-min-microvolt = <2960000>;
 448                         regulator-max-microvolt = <3008000>;
 449                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 450                 };
 451
 452                 vreg_l12c_1p8: ldo12 {
 453                         regulator-name = "vreg_l12c_1p8";
 454                         regulator-min-microvolt = <1800000>;
 455                         regulator-max-microvolt = <1968000>;
 456                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 457                 };
 458
 459                 vreg_l13c_3p0: ldo13 {
 460                         regulator-name = "vreg_l13c_3p0";
 461                         regulator-min-microvolt = <3000000>;
 462                         regulator-max-microvolt = <3000000>;
 463                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 464                 };
 465         };
 466
 467         regulators-2 {
 468                 compatible = "qcom,pm8450-rpmh-regulators";
 469                 qcom,pmic-id = "h";
 470
 471                 vdd-s1-supply = <&vph_pwr>;
 472                 vdd-s2-supply = <&vph_pwr>;
 473                 vdd-s3-supply = <&vph_pwr>;
 474                 vdd-s4-supply = <&vph_pwr>;
 475                 vdd-s5-supply = <&vph_pwr>;
 476                 vdd-s6-supply = <&vph_pwr>;
 477
 478                 vdd-l2-supply = <&vreg_bob>;
 479                 vdd-l3-supply = <&vreg_bob>;
 480                 vdd-l4-supply = <&vreg_bob>;
 481
 482                 vreg_s2h_0p95: smps2 {
 483                         regulator-name = "vreg_s2h_0p95";
 484                         regulator-min-microvolt = <848000>;
 485                         regulator-max-microvolt = <1104000>;
 486                 };
 487
 488                 vreg_s3h_0p5: smps3 {
 489                         regulator-name = "vreg_s3h_0p5";
 490                         regulator-min-microvolt = <500000>;
 491                         regulator-max-microvolt = <500000>;
 492                 };
 493
 494                 vreg_l2h_0p91: ldo2 {
 495                         regulator-name = "vreg_l2h_0p91";
 496                         regulator-min-microvolt = <880000>;
 497                         regulator-max-microvolt = <912000>;
 498                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 499                 };
 500
 501                 vreg_l3h_0p91: ldo3 {
 502                         regulator-name = "vreg_l3h_0p91";
 503                         regulator-min-microvolt = <912000>;
 504                         regulator-max-microvolt = <912000>;
 505                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 506                 };
 507         };
 508
 509         regulators-3 {
 510                 compatible = "qcom,pmr735a-rpmh-regulators";
 511                 qcom,pmic-id = "e";
 512
 513                 vdd-s1-supply = <&vph_pwr>;
 514                 vdd-s2-supply = <&vph_pwr>;
 515                 vdd-s3-supply = <&vph_pwr>;
 516
 517                 vdd-l1-l2-supply = <&vreg_s2e_0p85>;
 518                 vdd-l3-supply = <&vreg_s1e_1p25>;
 519                 vdd-l4-supply = <&vreg_s1c_1p86>;
 520                 vdd-l5-l6-supply = <&vreg_s1c_1p86>;
 521                 vdd-l7-bob-supply = <&vreg_bob>;
 522
 523                 vreg_s1e_1p25: smps1 {
 524                         regulator-name = "vreg_s1e_1p25";
 525                         regulator-min-microvolt = <1200000>;
 526                         regulator-max-microvolt = <1296000>;
 527                 };
 528
 529                 vreg_s2e_0p85: smps2 {
 530                         regulator-name = "vreg_s2e_0p85";
 531                         regulator-min-microvolt = <500000>;
 532                         regulator-max-microvolt = <1040000>;
 533                 };
 534
 535                 vreg_l1e_0p8: ldo1 {
 536                         regulator-name = "vreg_l1e_0p8";
 537                         regulator-min-microvolt = <800000>;
 538                         regulator-max-microvolt = <800000>;
 539                 };
 540
 541                 vreg_l2e_0p8: ldo2 {
 542                         regulator-name = "vreg_l2e_0p8";
 543                         regulator-min-microvolt = <800000>;
 544                         regulator-max-microvolt = <800000>;
 545                 };
 546
 547                 vreg_l3e_1p2: ldo3 {
 548                         regulator-name = "vreg_l3e_1p2";
 549                         regulator-min-microvolt = <1200000>;
 550                         regulator-max-microvolt = <1200000>;
 551                 };
 552
 553                 vreg_l4e_1p7: ldo4 {
 554                         regulator-name = "vreg_l4e_1p7";
 555                         regulator-min-microvolt = <1776000>;
 556                         regulator-max-microvolt = <1776000>;
 557                 };
 558
 559                 vreg_l5e_0p88: ldo5 {
 560                         regulator-name = "vreg_l5e_0p88";
 561                         regulator-min-microvolt = <880000>;
 562                         regulator-max-microvolt = <880000>;
 563                 };
 564
 565                 vreg_l6e_1p2: ldo6 {
 566                         regulator-name = "vreg_l6e_1p2";
 567                         regulator-min-microvolt = <1200000>;
 568                         regulator-max-microvolt = <1200000>;
 569                 };
 570
 571                 vreg_l7e_2p8: ldo7 {
 572                         regulator-name = "vreg_l7e_2p8";
 573                         regulator-min-microvolt = <2800000>;
 574                         regulator-max-microvolt = <2800000>;
 575                 };
 576         };
 577 };
 578
 579 &dispcc {
 580         status = "okay";
 581 };
 582
 583 &i2c9 {
 584         clock-frequency = <400000>;
 585         status = "okay";
 586
 587         lt9611_codec: hdmi-bridge@2b {
 588                 compatible = "lontium,lt9611uxc";
 589                 reg = <0x2b>;
 590
 591                 interrupts-extended = <&tlmm 44 IRQ_TYPE_EDGE_FALLING>;
 592
 593                 reset-gpios = <&tlmm 107 GPIO_ACTIVE_HIGH>;
 594
 595                 vdd-supply = <&lt9611_1v2>;
 596                 vcc-supply = <&lt9611_3v3>;
 597
 598                 pinctrl-names = "default";
 599                 pinctrl-0 = <&lt9611_irq_pin &lt9611_rst_pin>;
 600
 601                 ports {
 602                         #address-cells = <1>;
 603                         #size-cells = <0>;
 604
 605                         port@0 {
 606                                 reg = <0>;
 607
 608                                 lt9611_a: endpoint {
 609                                         remote-endpoint = <&mdss_dsi0_out>;
 610                                 };
 611                         };
 612
 613                         port@2 {
 614                                 reg = <2>;
 615
 616                                 lt9611_out: endpoint {
 617                                         remote-endpoint = <&hdmi_connector_out>;
 618                                 };
 619                         };
 620                 };
 621         };
 622 };
 623
 624 &i2c5 {
 625         clock-frequency = <100000>;
 626
 627         status = "okay";
 628
 629         typec-mux@42 {
 630                 compatible = "fcs,fsa4480";
 631                 reg = <0x42>;
 632
 633                 interrupts-extended = <&tlmm 2 IRQ_TYPE_LEVEL_LOW>;
 634
 635                 vcc-supply = <&vreg_bob>;
 636                 mode-switch;
 637                 orientation-switch;
 638
 639                 port {
 640                         fsa4480_sbu_mux: endpoint {
 641                                 remote-endpoint = <&pmic_glink_sbu>;
 642                         };
 643                 };
 644         };
 645 };
 646
 647 &mdss {
 648         status = "okay";
 649 };
 650
 651 &mdss_dsi0 {
 652         vdda-supply = <&vreg_l6b_1p2>;
 653         status = "okay";
 654 };
 655
 656 &mdss_dsi0_out {
 657         remote-endpoint = <&lt9611_a>;
 658         data-lanes = <0 1 2 3>;
 659 };
 660
 661 &mdss_dsi0_phy {
 662         vdds-supply = <&vreg_l5b_0p88>;
 663         status = "okay";
 664 };
 665
 666 &mdss_dp0 {
 667         status = "okay";
 668
 669         ports {
 670                 port@1 {
 671                         reg = <1>;
 672
 673                         mdss_dp0_out: endpoint {
 674                                 data-lanes = <0 1>;
 675                                 remote-endpoint = <&usb_1_qmpphy_dp_in>;
 676                         };
 677                 };
 678         };
 679 };
 680
 681 &pcie0 {
 682         status = "okay";
 683         max-link-speed = <2>;
 684 };
 685
 686 &pcie0_phy {
 687         status = "okay";
 688         vdda-phy-supply = <&vreg_l5b_0p88>;
 689         vdda-pll-supply = <&vreg_l6b_1p2>;
 690 };
 691
 692 &pcie1 {
 693         status = "okay";
 694 };
 695
 696 &pcie1_phy {
 697         status = "okay";
 698         vdda-phy-supply = <&vreg_l2h_0p91>;
 699         vdda-pll-supply = <&vreg_l6b_1p2>;
 700 };
 701
 702 &pm8350_temp_alarm {
 703         io-channels = <&pmk8350_vadc PM8350_ADC7_DIE_TEMP(1)>;
 704         io-channel-names = "thermal";
 705 };
 706
 707 &pm8350b_temp_alarm {
 708         io-channels = <&pmk8350_vadc PM8350B_ADC7_DIE_TEMP>;
 709         io-channel-names = "thermal";
 710 };
 711
 712 &pmr735a_temp_alarm {
 713         io-channels = <&pmk8350_vadc PMR735A_ADC7_DIE_TEMP>;
 714         io-channel-names = "thermal";
 715 };
 716
 717 &pmk8350_adc_tm {
 718         status = "okay";
 719
 720         xo-therm@0 {
 721                 reg = <0>;
 722                 io-channels = <&pmk8350_vadc PMK8350_ADC7_AMUX_THM1_100K_PU>;
 723                 qcom,ratiometric;
 724                 qcom,hw-settle-time-us = <200>;
 725         };
 726
 727         skin-msm-therm@1 {
 728                 reg = <1>;
 729                 io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM1_100K_PU(1)>;
 730                 qcom,ratiometric;
 731                 qcom,hw-settle-time-us = <200>;
 732         };
 733
 734         camera-therm@2 {
 735                 reg = <2>;
 736                 io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM2_100K_PU(1)>;
 737                 qcom,ratiometric;
 738                 qcom,hw-settle-time-us = <200>;
 739         };
 740
 741         therm1-therm@3 {
 742                 reg = <3>;
 743                 io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM3_100K_PU(1)>;
 744                 qcom,ratiometric;
 745                 qcom,hw-settle-time-us = <200>;
 746         };
 747
 748         wide-rfc-therm@4 {
 749                 reg = <4>;
 750                 io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM4_100K_PU(1)>;
 751                 qcom,ratiometric;
 752                 qcom,hw-settle-time-us = <200>;
 753         };
 754
 755         rear-tof-therm@5 {
 756                 reg = <5>;
 757                 io-channels = <&pmk8350_vadc PM8350_ADC7_AMUX_THM5_100K_PU(1)>;
 758                 qcom,ratiometric;
 759                 qcom,hw-settle-time-us = <200>;
 760         };
 761
 762         therm2-therm@6 {
 763                 reg = <6>;
 764                 io-channels = <&pmk8350_vadc PM8350_ADC7_GPIO3_100K_PU(1)>;
 765                 qcom,ratiometric;
 766                 qcom,hw-settle-time-us = <200>;
 767         };
 768
 769         usb-conn-therm@7 {
 770                 reg = <7>;
 771                 io-channels = <&pmk8350_vadc PM8350B_ADC7_AMUX_THM5_100K_PU>;
 772                 qcom,ratiometric;
 773                 qcom,hw-settle-time-us = <200>;
 774         };
 775 };
 776
 777 &pmk8350_vadc {
 778         status = "okay";
 779
 780         channel@3 {
 781                 reg = <PMK8350_ADC7_DIE_TEMP>;
 782                 label = "pmk8350_die_temp";
 783         };
 784
 785         channel@44 {
 786                 reg = <PMK8350_ADC7_AMUX_THM1_100K_PU>;
 787                 qcom,hw-settle-time = <200>;
 788                 qcom,ratiometric;
 789                 label = "pmk8350_xo_therm";
 790         };
 791
 792         channel@103 {
 793                 reg = <PM8350_ADC7_DIE_TEMP(1)>;
 794                 label = "pm8350_die_temp";
 795         };
 796
 797         channel@144 {
 798                 reg = <PM8350_ADC7_AMUX_THM1_100K_PU(1)>;
 799                 qcom,hw-settle-time = <200>;
 800                 qcom,ratiometric;
 801                 label = "skin_msm_temp";
 802         };
 803
 804         channel@145 {
 805                 reg = <PM8350_ADC7_AMUX_THM2_100K_PU(1)>;
 806                 qcom,hw-settle-time = <200>;
 807                 qcom,ratiometric;
 808                 label = "camera_temp";
 809         };
 810
 811         channel@146 {
 812                 reg = <PM8350_ADC7_AMUX_THM3_100K_PU(1)>;
 813                 qcom,hw-settle-time = <200>;
 814                 qcom,ratiometric;
 815                 label = "therm1_temp";
 816         };
 817
 818         channel@147 {
 819                 reg = <PM8350_ADC7_AMUX_THM4_100K_PU(1)>;
 820                 qcom,hw-settle-time = <200>;
 821                 qcom,ratiometric;
 822                 label = "wide_rfc_temp";
 823         };
 824
 825         channel@148 {
 826                 reg = <PM8350_ADC7_AMUX_THM5_100K_PU(1)>;
 827                 qcom,hw-settle-time = <200>;
 828                 qcom,ratiometric;
 829                 label = "rear_tof_temp";
 830         };
 831
 832         channel@14c {
 833                 reg = <PM8350_ADC7_GPIO3_100K_PU(1)>;
 834                 qcom,hw-settle-time = <200>;
 835                 qcom,ratiometric;
 836                 label = "therm2_temp";
 837         };
 838
 839         channel@303 {
 840                 reg = <PM8350B_ADC7_DIE_TEMP>;
 841                 label = "pm8350b_die_temp";
 842         };
 843
 844         channel@348 {
 845                 reg = <PM8350B_ADC7_AMUX_THM5_100K_PU>;
 846                 qcom,hw-settle-time = <200>;
 847                 qcom,ratiometric;
 848                 label = "usb_conn_temp";
 849         };
 850
 851         channel@403 {
 852                 reg = <PMR735A_ADC7_DIE_TEMP>;
 853                 label = "pmr735a_die_temp";
 854         };
 855
 856         channel@44a {
 857                 reg = <PMR735A_ADC7_GPIO1_100K_PU>;
 858                 qcom,hw-settle-time = <200>;
 859                 qcom,ratiometric;
 860                 label = "qtm_w_temp";
 861         };
 862
 863         channel@44b {
 864                 reg = <PMR735A_ADC7_GPIO2_100K_PU>;
 865                 qcom,hw-settle-time = <200>;
 866                 qcom,ratiometric;
 867                 label = "qtm_n_temp";
 868         };
 869 };
 870
 871 &remoteproc_adsp {
 872         status = "okay";
 873         firmware-name = "/*(DEBLOBBED)*/";
 874 };
 875
 876 &remoteproc_cdsp {
 877         status = "okay";
 878         firmware-name = "/*(DEBLOBBED)*/";
 879 };
 880
 881 &remoteproc_mpss {
 882         status = "okay";
 883         firmware-name = "/*(DEBLOBBED)*/";
 884 };
 885
 886 &remoteproc_slpi {
 887         status = "okay";
 888         firmware-name = "/*(DEBLOBBED)*/";
 889 };
 890
 891 &qupv3_id_0 {
 892         status = "okay";
 893 };
 894
 895 &qupv3_id_1 {
 896         status = "okay";
 897 };
 898
 899 &sdhc_2 {
 900         cd-gpios = <&tlmm 92 GPIO_ACTIVE_HIGH>;
 901         pinctrl-names = "default", "sleep";
 902         pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>;
 903         pinctrl-1 = <&sdc2_sleep_state &sdc2_card_det_n>;
 904         vmmc-supply = <&vreg_l9c_2p96>;
 905         vqmmc-supply = <&vreg_l6c_1p8>;
 906         no-sdio;
 907         no-mmc;
 908         status = "okay";
 909 };
 910
 911 &sound {
 912         compatible = "qcom,sm8450-sndcard";
 913         model = "SM8450-HDK";
 914         audio-routing = "SpkrLeft IN", "WSA_SPK1 OUT",
 915                         "SpkrRight IN", "WSA_SPK2 OUT",
 916                         "IN1_HPHL", "HPHL_OUT",
 917                         "IN2_HPHR", "HPHR_OUT",
 918                         "AMIC1", "MIC BIAS1",
 919                         "AMIC2", "MIC BIAS2",
 920                         "AMIC3", "MIC BIAS3",
 921                         "AMIC4", "MIC BIAS3",
 922                         "AMIC5", "MIC BIAS4",
 923                         "VA DMIC0", "MIC BIAS3",
 924                         "VA DMIC1", "MIC BIAS3",
 925                         "VA DMIC2", "MIC BIAS1",
 926                         "VA DMIC3", "MIC BIAS1",
 927                         "TX DMIC0", "MIC BIAS3",
 928                         "TX DMIC1", "MIC BIAS3",
 929                         "TX DMIC2", "MIC BIAS1",
 930                         "TX DMIC3", "MIC BIAS1",
 931                         "TX SWR_INPUT0", "ADC1_OUTPUT",
 932                         "TX SWR_INPUT1", "ADC2_OUTPUT",
 933                         "TX SWR_INPUT2", "ADC3_OUTPUT",
 934                         "TX SWR_INPUT3", "ADC4_OUTPUT";
 935
 936         wcd-playback-dai-link {
 937                 link-name = "WCD Playback";
 938
 939                 cpu {
 940                         sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
 941                 };
 942
 943                 codec {
 944                         sound-dai = <&wcd938x 0>, <&swr1 0>, <&rxmacro 0>;
 945                 };
 946
 947                 platform {
 948                         sound-dai = <&q6apm>;
 949                 };
 950         };
 951
 952         wcd-capture-dai-link {
 953                 link-name = "WCD Capture";
 954
 955                 cpu {
 956                         sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
 957                 };
 958
 959                 codec {
 960                         sound-dai = <&wcd938x 1>, <&swr2 0>, <&txmacro 0>;
 961                 };
 962
 963                 platform {
 964                         sound-dai = <&q6apm>;
 965                 };
 966         };
 967
 968         wsa-dai-link {
 969                 link-name = "WSA Playback";
 970
 971                 cpu {
 972                         sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
 973                 };
 974
 975                 codec {
 976                         sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&wsamacro 0>;
 977                 };
 978
 979                 platform {
 980                         sound-dai = <&q6apm>;
 981                 };
 982         };
 983
 984         va-dai-link {
 985                 link-name = "VA Capture";
 986
 987                 cpu {
 988                         sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
 989                 };
 990
 991                 codec {
 992                         sound-dai = <&vamacro 0>;
 993                 };
 994
 995                 platform {
 996                         sound-dai = <&q6apm>;
 997                 };
 998         };
 999 };
1000
1001 &swr0 {
1002         status = "okay";
1003
1004         left_spkr: speaker@0,1 {
1005                 compatible = "sdw10217020200";
1006                 reg = <0 1>;
1007                 pinctrl-names = "default";
1008                 pinctrl-0 = <&spkr_1_sd_n_active>;
1009                 powerdown-gpios = <&tlmm 1 GPIO_ACTIVE_LOW>;
1010                 #sound-dai-cells = <0>;
1011                 sound-name-prefix = "SpkrLeft";
1012                 #thermal-sensor-cells = <0>;
1013                 vdd-supply = <&vreg_s10b_1p8>;
1014         };
1015
1016         right_spkr: speaker@0,2 {
1017                 compatible = "sdw10217020200";
1018                 reg = <0 2>;
1019                 pinctrl-names = "default";
1020                 pinctrl-0 = <&spkr_2_sd_n_active>;
1021                 powerdown-gpios = <&tlmm 89 GPIO_ACTIVE_LOW>;
1022                 #sound-dai-cells = <0>;
1023                 sound-name-prefix = "SpkrRight";
1024                 #thermal-sensor-cells = <0>;
1025                 vdd-supply = <&vreg_s10b_1p8>;
1026         };
1027 };
1028
1029 &swr1 {
1030         status = "okay";
1031
1032         wcd_rx: codec@0,4 {
1033                 compatible = "sdw20217010d00";
1034                 reg = <0 4>;
1035                 qcom,rx-port-mapping = <1 2 3 4 5>;
1036         };
1037 };
1038
1039 &swr2 {
1040         status = "okay";
1041
1042         wcd_tx: codec@0,3 {
1043                 compatible = "sdw20217010d00";
1044                 reg = <0 3>;
1045                 qcom,tx-port-mapping = <1 1 2 3>;
1046         };
1047 };
1048
1049 &tlmm {
1050         gpio-reserved-ranges = <28 4>, <36 4>;
1051
1052         lt9611_irq_pin: lt9611-irq-state {
1053                 pins = "gpio44";
1054                 function = "gpio";
1055                 bias-disable;
1056         };
1057
1058         lt9611_rst_pin: lt9611-rst-state {
1059                 pins = "gpio107";
1060                 function = "gpio";
1061                 output-high;
1062         };
1063
1064         sdc2_card_det_n: sd-card-det-n-state {
1065                 pins = "gpio92";
1066                 function = "gpio";
1067                 drive-strength = <2>;
1068                 bias-pull-up;
1069         };
1070 };
1071
1072 &uart7 {
1073         status = "okay";
1074 };
1075
1076 &ufs_mem_hc {
1077         status = "okay";
1078
1079         reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
1080
1081         vcc-supply = <&vreg_l7b_2p5>;
1082         vcc-max-microamp = <1100000>;
1083         vccq-supply = <&vreg_l9b_1p2>;
1084         vccq-max-microamp = <1200000>;
1085         vdd-hba-supply = <&vreg_l9b_1p2>;
1086 };
1087
1088 &ufs_mem_phy {
1089         status = "okay";
1090
1091         vdda-phy-supply = <&vreg_l5b_0p88>;
1092         vdda-pll-supply = <&vreg_l6b_1p2>;
1093 };
1094
1095 &usb_1 {
1096         status = "okay";
1097 };
1098
1099 &usb_1_dwc3 {
1100         dr_mode = "otg";
1101         usb-role-switch;
1102 };
1103
1104 &usb_1_dwc3_hs {
1105         remote-endpoint = <&pmic_glink_hs_in>;
1106 };
1107
1108 &usb_1_dwc3_ss {
1109         remote-endpoint = <&usb_1_qmpphy_usb_ss_in>;
1110 };
1111
1112 &usb_1_hsphy {
1113         status = "okay";
1114
1115         vdda-pll-supply = <&vreg_l5b_0p88>;
1116         vdda18-supply = <&vreg_l1c_1p8>;
1117         vdda33-supply = <&vreg_l2b_3p07>;
1118 };
1119
1120 &usb_1_qmpphy {
1121         status = "okay";
1122
1123         vdda-phy-supply = <&vreg_l6b_1p2>;
1124         vdda-pll-supply = <&vreg_l1b_0p91>;
1125
1126         orientation-switch;
1127 };
1128
1129 &usb_1_qmpphy_dp_in {
1130         remote-endpoint = <&mdss_dp0_out>;
1131 };
1132
1133 &usb_1_qmpphy_out {
1134         remote-endpoint = <&pmic_glink_ss_in>;
1135 };
1136
1137 &usb_1_qmpphy_usb_ss_in {
1138         remote-endpoint = <&usb_1_dwc3_ss>;
1139 };
1140
1141 &vamacro {
1142         pinctrl-0 = <&dmic01_default>, <&dmic02_default>;
1143         pinctrl-names = "default";
1144         vdd-micb-supply = <&vreg_s10b_1p8>;
1145         qcom,dmic-sample-rate = <600000>;
1146
1147         status = "okay";
1148 };
1149
1150 &tlmm {
1151         spkr_1_sd_n_active: spkr-1-sd-n-active-state {
1152                 pins = "gpio1";
1153                 function = "gpio";
1154                 drive-strength = <16>;
1155                 bias-disable;
1156                 output-low;
1157         };
1158
1159         spkr_2_sd_n_active: spkr-2-sd-n-active-state {
1160                 pins = "gpio89";
1161                 function = "gpio";
1162                 drive-strength = <16>;
1163                 bias-disable;
1164                 output-low;
1165         };
1166
1167         wcd_default: wcd-reset-n-active-state {
1168                 pins = "gpio43";
1169                 function = "gpio";
1170                 drive-strength = <16>;
1171                 bias-disable;
1172                 output-low;
1173         };
1174 };