arch/arm64/boot/dts/qcom/sdm845-xiaomi-polaris.dts

   1 // SPDX-License-Identifier: BSD-3-Clause
   2 /*
   3  * Copyright (c) 2020, Xilin Wu <strongtz@yeah.net>
   4  * Copyright (c) 2022, Molly Sophia <mollysophia379@gmail.com>
   5  */
   6
   7 /dts-v1/;
   8
   9 #include <dt-bindings/gpio/gpio.h>
  10 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
  11 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
  12 #include <dt-bindings/input/linux-event-codes.h>
  13 #include <dt-bindings/sound/qcom,q6afe.h>
  14 #include <dt-bindings/sound/qcom,q6asm.h>
  15 #include "sdm845.dtsi"
  16 #include "pm8998.dtsi"
  17 #include "pmi8998.dtsi"
  18 #include "pm8005.dtsi"
  19
  20 /*
  21  * Delete following upstream (sdm845.dtsi) reserved
  22  * memory mappings which are different in this device.
  23  */
  24 /delete-node/ &rmtfs_mem;
  25 /delete-node/ &adsp_mem;
  26 /delete-node/ &wlan_msa_mem;
  27 /delete-node/ &mpss_region;
  28 /delete-node/ &venus_mem;
  29 /delete-node/ &cdsp_mem;
  30 /delete-node/ &mba_region;
  31 /delete-node/ &slpi_mem;
  32 /delete-node/ &spss_mem;
  33
  34 / {
  35         model = "Xiaomi Mi MIX 2S";
  36         compatible = "xiaomi,polaris", "qcom,sdm845";
  37         chassis-type = "handset";
  38
  39         /* required for bootloader to select correct board */
  40         qcom,msm-id = <0x141 0x20001>;
  41         qcom,board-id = <0x2a 0x0>;
  42
  43         aliases {
  44                 serial0 = &uart9;
  45                 serial1 = &uart6;
  46         };
  47
  48         gpio-keys {
  49                 compatible = "gpio-keys";
  50                 autorepeat;
  51
  52                 pinctrl-names = "default";
  53                 pinctrl-0 = <&volume_up_gpio>;
  54
  55                 key-vol-up {
  56                         label = "Volume Up";
  57                         linux,code = <KEY_VOLUMEUP>;
  58                         gpios = <&pm8998_gpio 6 GPIO_ACTIVE_LOW>;
  59                         debounce-interval = <15>;
  60                 };
  61         };
  62
  63         reserved-memory {
  64                 adsp_mem: memory@8c500000 {
  65                         reg = <0 0x8c500000 0 0x1e00000>;
  66                         no-map;
  67                 };
  68
  69                 wlan_msa_mem: memory@8e300000 {
  70                         reg = <0 0x8e300000 0 0x100000>;
  71                         no-map;
  72                 };
  73
  74                 mpss_region: memory@8e400000 {
  75                         reg = <0 0x8e400000 0 0x7800000>;
  76                         no-map;
  77                 };
  78
  79                 venus_mem: memory@95c00000 {
  80                         reg = <0 0x95c00000 0 0x500000>;
  81                         no-map;
  82                 };
  83
  84                 cdsp_mem: memory@96100000 {
  85                         reg = <0 0x96100000 0 0x800000>;
  86                         no-map;
  87                 };
  88
  89                 mba_region: memory@96900000 {
  90                         reg = <0 0x96900000 0 0x200000>;
  91                         no-map;
  92                 };
  93
  94                 slpi_mem: memory@96b00000 {
  95                         reg = <0 0x96b00000 0 0x1400000>;
  96                         no-map;
  97                 };
  98
  99                 spss_mem: memory@97f00000 {
 100                         reg = <0 0x97f00000 0 0x100000>;
 101                         no-map;
 102                 };
 103
 104                 rmtfs_mem: memory@f6301000 {
 105                         compatible = "qcom,rmtfs-mem";
 106                         reg = <0 0xf6301000 0 0x200000>;
 107                         no-map;
 108
 109                         qcom,client-id = <1>;
 110                         qcom,vmid = <15>;
 111                 };
 112         };
 113
 114         battery: battery {
 115                 compatible = "simple-battery";
 116
 117                 charge-full-design-microamp-hours = <3400000>;
 118                 voltage-min-design-microvolt = <3400000>;
 119                 voltage-max-design-microvolt = <4400000>;
 120         };
 121
 122         vreg_tp_vddio: vreg-tp-vddio {
 123                 compatible = "regulator-fixed";
 124                 regulator-name = "vreg_tp_vddio";
 125
 126                 regulator-min-microvolt = <1800000>;
 127                 regulator-max-microvolt = <1800000>;
 128
 129                 gpio = <&tlmm 23 GPIO_ACTIVE_HIGH>;
 130                 regulator-always-on;
 131                 regulator-boot-on;
 132                 enable-active-high;
 133         };
 134
 135         vreg_s4a_1p8: vreg-s4a-1p8 {
 136                 compatible = "regulator-fixed";
 137                 regulator-name = "vreg_s4a_1p8";
 138
 139                 regulator-min-microvolt = <1800000>;
 140                 regulator-max-microvolt = <1800000>;
 141                 regulator-always-on;
 142         };
 143 };
 144
 145 &apps_rsc {
 146         regulators-0 {
 147                 compatible = "qcom,pm8998-rpmh-regulators";
 148                 qcom,pmic-id = "a";
 149
 150                 vreg_s2a_1p1: smps2 {
 151                         regulator-min-microvolt = <1100000>;
 152                         regulator-max-microvolt = <1100000>;
 153                 };
 154
 155                 vreg_s3a_1p35: smps3 {
 156                         regulator-min-microvolt = <1352000>;
 157                         regulator-max-microvolt = <1352000>;
 158                 };
 159
 160                 vreg_s5a_2p04: smps5 {
 161                         regulator-min-microvolt = <1904000>;
 162                         regulator-max-microvolt = <2040000>;
 163                 };
 164
 165                 vreg_s7a_1p025: smps7 {
 166                         regulator-min-microvolt = <900000>;
 167                         regulator-max-microvolt = <1028000>;
 168                 };
 169
 170                 vdda_mipi_dsi0_pll:
 171                 vdda_ufs1_core:
 172                 vreg_l1a_0p875: ldo1 {
 173                         regulator-min-microvolt = <880000>;
 174                         regulator-max-microvolt = <880000>;
 175                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 176                 };
 177
 178                 vreg_l2a_1p2: ldo2 {
 179                         regulator-min-microvolt = <1200000>;
 180                         regulator-max-microvolt = <1200000>;
 181                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 182                         regulator-always-on;
 183                 };
 184
 185                 vreg_l3a_1p0: ldo3 {
 186                         regulator-min-microvolt = <1000000>;
 187                         regulator-max-microvolt = <1000000>;
 188                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 189                 };
 190
 191                 vreg_l5a_0p8: ldo5 {
 192                         regulator-min-microvolt = <800000>;
 193                         regulator-max-microvolt = <800000>;
 194                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 195                 };
 196
 197                 vreg_l6a_1p8: ldo6 {
 198                         regulator-min-microvolt = <1856000>;
 199                         regulator-max-microvolt = <1856000>;
 200                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 201                 };
 202
 203                 vreg_l7a_1p8: ldo7 {
 204                         regulator-min-microvolt = <1800000>;
 205                         regulator-max-microvolt = <1800000>;
 206                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 207                 };
 208
 209                 vreg_l8a_1p2: ldo8 {
 210                         regulator-min-microvolt = <1200000>;
 211                         regulator-max-microvolt = <1248000>;
 212                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 213                 };
 214
 215                 vreg_l9a_1p8: ldo9 {
 216                         regulator-min-microvolt = <1704000>;
 217                         regulator-max-microvolt = <2928000>;
 218                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 219                 };
 220
 221                 vreg_l10a_2p95: ldo10 {
 222                         regulator-min-microvolt = <1704000>;
 223                         regulator-max-microvolt = <2928000>;
 224                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 225                 };
 226
 227                 vreg_l11a_1p05: ldo11 {
 228                         regulator-min-microvolt = <1000000>;
 229                         regulator-max-microvolt = <1048000>;
 230                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 231                 };
 232
 233                 vreg_l12a_1p8: ldo12 {
 234                         regulator-min-microvolt = <1800000>;
 235                         regulator-max-microvolt = <1800000>;
 236                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 237                 };
 238
 239                 vreg_l13a_2p95: ldo13 {
 240                         regulator-min-microvolt = <1800000>;
 241                         regulator-max-microvolt = <2960000>;
 242                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 243                 };
 244
 245                 vreg_l14a_1p8: ldo14 {
 246                         regulator-min-microvolt = <1800000>;
 247                         regulator-max-microvolt = <1880000>;
 248                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 249                         regulator-always-on;
 250                 };
 251
 252                 vreg_l15a_1p8: ldo15 {
 253                         regulator-min-microvolt = <1800000>;
 254                         regulator-max-microvolt = <1800000>;
 255                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 256                 };
 257
 258                 vreg_l16a_2p7: ldo16 {
 259                         regulator-min-microvolt = <2704000>;
 260                         regulator-max-microvolt = <2704000>;
 261                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 262                 };
 263
 264                 vreg_l17a_1p3: ldo17 {
 265                         regulator-min-microvolt = <1304000>;
 266                         regulator-max-microvolt = <1304000>;
 267                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 268                         regulator-always-on;
 269                 };
 270
 271                 vreg_l18a_2p9: ldo18 {
 272                         regulator-min-microvolt = <2704000>;
 273                         regulator-max-microvolt = <2960000>;
 274                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 275                 };
 276
 277                 vreg_l19a_3p1: ldo19 {
 278                         regulator-min-microvolt = <2856000>;
 279                         regulator-max-microvolt = <3104000>;
 280                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 281                 };
 282
 283                 vreg_l20a_2p95: ldo20 {
 284                         regulator-min-microvolt = <2704000>;
 285                         regulator-max-microvolt = <2960000>;
 286                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 287                 };
 288
 289                 vreg_l21a_2p95: ldo21 {
 290                         regulator-min-microvolt = <2704000>;
 291                         regulator-max-microvolt = <2960000>;
 292                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 293                 };
 294
 295                 vreg_l22a_3p3: ldo22 {
 296                         regulator-min-microvolt = <2864000>;
 297                         regulator-max-microvolt = <3312000>;
 298                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 299                 };
 300
 301                 vreg_l23a_3p3: ldo23 {
 302                         regulator-min-microvolt = <3000000>;
 303                         regulator-max-microvolt = <3312000>;
 304                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 305                 };
 306
 307                 vreg_l24a_3p075: ldo24 {
 308                         regulator-min-microvolt = <3088000>;
 309                         regulator-max-microvolt = <3088000>;
 310                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 311                 };
 312
 313                 vreg_l25a_3p3: ldo25 {
 314                         regulator-min-microvolt = <3000000>;
 315                         regulator-max-microvolt = <3312000>;
 316                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 317                         regulator-always-on;
 318                 };
 319
 320                 vdda_mipi_dsi0_1p2:
 321                 vdda_ufs1_1p2:
 322                 vreg_l26a_1p2: ldo26 {
 323                         regulator-min-microvolt = <1200000>;
 324                         regulator-max-microvolt = <1200000>;
 325                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 326                 };
 327
 328                 vreg_l28a_3p0: ldo28 {
 329                         regulator-min-microvolt = <2856000>;
 330                         regulator-max-microvolt = <3008000>;
 331                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 332                         regulator-always-on;
 333                 };
 334
 335                 vreg_lvs1a_1p8: lvs1 {
 336                         regulator-min-microvolt = <1800000>;
 337                         regulator-max-microvolt = <1800000>;
 338                 };
 339
 340                 vreg_lvs2a_1p8: lvs2 {
 341                         regulator-min-microvolt = <1800000>;
 342                         regulator-max-microvolt = <1800000>;
 343                 };
 344         };
 345
 346         regulators-1 {
 347                 compatible = "qcom,pmi8998-rpmh-regulators";
 348                 qcom,pmic-id = "b";
 349
 350                 vreg_bob: bob {
 351                         regulator-min-microvolt = <3312000>;
 352                         regulator-max-microvolt = <3600000>;
 353                         regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
 354                         regulator-allow-bypass;
 355                 };
 356         };
 357
 358         regulators-2 {
 359                 compatible = "qcom,pm8005-rpmh-regulators";
 360                 qcom,pmic-id = "c";
 361
 362                 vreg_smp3c_0p6: smps3 {
 363                         regulator-min-microvolt = <600000>;
 364                         regulator-max-microvolt = <600000>;
 365                         regulator-always-on;
 366                 };
 367         };
 368 };
 369
 370 &cdsp_pas {
 371         firmware-name = "/*(DEBLOBBED)*/";
 372         status = "okay";
 373 };
 374
 375 &dsi0 {
 376         vdda-supply = <&vdda_mipi_dsi0_1p2>;
 377         status = "okay";
 378
 379         display_panel: panel@0 {
 380                 compatible = "jdi,fhd-nt35596s";
 381                 #address-cells = <1>;
 382                 #size-cells = <0>;
 383                 reg = <0>;
 384
 385                 reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
 386                 vddio-supply = <&vreg_l14a_1p8>;
 387                 backlight = <&pmi8998_wled>;
 388                 vddpos-supply = <&lab>;
 389                 vddneg-supply = <&ibb>;
 390
 391                 pinctrl-names = "default", "sleep";
 392                 pinctrl-0 = <&sde_dsi_active>;
 393                 pinctrl-1 = <&sde_dsi_suspend>;
 394
 395                 port {
 396                         panel_in: endpoint {
 397                                 remote-endpoint = <&dsi0_out>;
 398                         };
 399                 };
 400         };
 401 };
 402
 403 &dsi0_out {
 404         remote-endpoint = <&panel_in>;
 405         data-lanes = <0 1 2 3>;
 406 };
 407
 408 &dsi0_phy {
 409         vdds-supply = <&vdda_mipi_dsi0_pll>;
 410         status = "okay";
 411 };
 412
 413 &gcc {
 414         protected-clocks = <GCC_QSPI_CORE_CLK>,
 415                                 <GCC_QSPI_CORE_CLK_SRC>,
 416                                 <GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
 417                                 <GCC_LPASS_Q6_AXI_CLK>,
 418                                 <GCC_LPASS_SWAY_CLK>;
 419 };
 420
 421 &gmu {
 422         status = "okay";
 423 };
 424
 425 &gpi_dma0 {
 426         status = "okay";
 427 };
 428
 429 &gpi_dma1 {
 430         status = "okay";
 431 };
 432
 433 &gpu {
 434         status = "okay";
 435
 436         zap-shader {
 437                 memory-region = <&gpu_mem>;
 438                 firmware-name = "/*(DEBLOBBED)*/";
 439         };
 440 };
 441
 442 &ibb {
 443         regulator-min-microvolt = <4600000>;
 444         regulator-max-microvolt = <6000000>;
 445         regulator-over-current-protection;
 446         regulator-pull-down;
 447         regulator-soft-start;
 448         qcom,discharge-resistor-kohms = <300>;
 449 };
 450
 451 &ipa {
 452         memory-region = <&ipa_fw_mem>;
 453         firmware-name = "/*(DEBLOBBED)*/";
 454         status = "okay";
 455 };
 456
 457 &i2c14 {
 458         clock-frequency = <400000>;
 459         dmas = <&gpi_dma1 0 6 QCOM_GPI_I2C>,
 460                    <&gpi_dma1 1 6 QCOM_GPI_I2C>;
 461         dma-names = "tx", "rx";
 462         status = "okay";
 463
 464         touchscreen@20 {
 465                 compatible = "syna,rmi4-i2c";
 466                 reg = <0x20>;
 467                 #address-cells = <1>;
 468                 #size-cells = <0>;
 469                 interrupts-extended = <&tlmm 125 0x2008>;
 470
 471                 pinctrl-names = "default", "sleep";
 472                 pinctrl-0 = <&ts_int_default &ts_reset_default>;
 473                 pinctrl-1 = <&ts_int_sleep &ts_reset_sleep>;
 474
 475                 vdd-supply = <&vreg_l28a_3p0>;
 476                 vio-supply = <&vreg_tp_vddio>;
 477
 478                 syna,startup-delay-ms = <0xc8>;
 479                 syna,reset-delay-ms = <0xc8>;
 480
 481                 rmi4-f01@1 {
 482                         syna,nosleep-mode = <0x1>;
 483                         reg = <0x1>;
 484                 };
 485
 486                 rmi4-f12@12 {
 487                         reg = <0x12>;
 488                         syna,rezero-wait-ms = <0xc8>;
 489                         syna,clip-x-high = <0x438>;
 490                         syna,clip-y-high = <0x870>;
 491                         syna,sensor-type = <0x1>;
 492                         syna,clip-x-low = <0x0>;
 493                         syna,clip-y-low = <0x0>;
 494                 };
 495         };
 496 };
 497
 498 &lab {
 499         regulator-min-microvolt = <4600000>;
 500         regulator-max-microvolt = <6000000>;
 501         regulator-soft-start;
 502         regulator-pull-down;
 503 };
 504
 505 &mdss {
 506         status = "okay";
 507 };
 508
 509 &mss_pil {
 510         firmware-name = "/*(DEBLOBBED)*/", "/*(DEBLOBBED)*/";
 511         status = "okay";
 512 };
 513
 514 &pmi8998_wled {
 515         qcom,current-limit-microamp = <20000>;
 516         qcom,current-boost-limit = <970>;
 517         qcom,ovp-millivolt = <19600>;
 518         qcom,switching-freq = <600>;
 519         qcom,num-strings = <4>;
 520         qcom,cabc;
 521
 522         status = "okay";
 523 };
 524
 525 &pm8998_gpio {
 526         volume_up_gpio: pm8998-gpio6-state {
 527                 pinconf {
 528                         qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
 529                         function = "normal";
 530                         pins = "gpio6";
 531                         input-enable;
 532                         bias-pull-up;
 533                 };
 534         };
 535 };
 536
 537 &pm8998_pon {
 538         resin {
 539                 interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
 540                 compatible = "qcom,pm8941-resin";
 541                 linux,code = <KEY_VOLUMEDOWN>;
 542                 debounce = <15625>;
 543                 bias-pull-up;
 544         };
 545 };
 546
 547 &q6afedai {
 548         qi2s@22 {
 549                 reg = <22>;
 550                 qcom,sd-lines = <0>;
 551         };
 552 };
 553
 554 &q6asmdai {
 555         dai@0 {
 556                 reg = <0>;
 557         };
 558
 559         dai@1 {
 560                 reg = <1>;
 561         };
 562
 563         dai@2 {
 564                 reg = <2>;
 565         };
 566 };
 567
 568 &qupv3_id_0 {
 569         status = "okay";
 570 };
 571
 572 &qupv3_id_1 {
 573         status = "okay";
 574 };
 575
 576 &qup_i2c14_default {
 577         pinconf {
 578                 pins = "gpio33", "gpio34";
 579                 drive-strength = <2>;
 580                 bias-disable;
 581         };
 582 };
 583
 584 &tlmm {
 585         gpio-reserved-ranges = <0 4>, <81 4>;
 586
 587         ts_reset_default: ts-reset-default {
 588                 pins = "gpio99";
 589                 function = "gpio";
 590                 drive-strength = <16>;
 591                 output-high;
 592         };
 593
 594         ts_int_default: ts-int-default {
 595                 pins = "gpio125";
 596                 function = "gpio";
 597                 bias-pull-down;
 598                 drive-strength = <16>;
 599                 input-enable;
 600         };
 601
 602         ts_reset_sleep: ts-reset-sleep {
 603                 pins = "gpio99";
 604                 function = "gpio";
 605                 bias-disable;
 606                 drive-strength = <2>;
 607         };
 608
 609         ts_int_sleep: ts-int-sleep {
 610                 pins = "gpio125";
 611                 function = "gpio";
 612                 bias-pull-down;
 613                 drive-strength = <2>;
 614                 input-enable;
 615         };
 616
 617         sde_dsi_active: sde-dsi-active {
 618                 pins = "gpio6", "gpio10";
 619                 function = "gpio";
 620                 drive-strength = <8>;
 621                 bias-disable;
 622         };
 623
 624         sde_dsi_suspend: sde-dsi-suspend {
 625                 pins = "gpio6", "gpio10";
 626                 function = "gpio";
 627                 drive-strength = <2>;
 628                 bias-pull-down;
 629         };
 630
 631         wcd_intr_default: wcd-intr-default {
 632                 pins = "gpio54";
 633                 function = "gpio";
 634                 input-enable;
 635                 bias-pull-down;
 636                 drive-strength = <2>;
 637         };
 638 };
 639
 640 &uart6 {
 641         status = "okay";
 642
 643         bluetooth {
 644                 compatible = "qcom,wcn3990-bt";
 645
 646                 /* This path is relative to the qca/ subdir under lib/firmware. */
 647                 firmware-name = "/*(DEBLOBBED)*/";
 648
 649                 vddio-supply = <&vreg_s4a_1p8>;
 650                 vddxo-supply = <&vreg_l7a_1p8>;
 651                 vddrf-supply = <&vreg_l17a_1p3>;
 652                 vddch0-supply = <&vreg_l25a_3p3>;
 653                 max-speed = <3200000>;
 654         };
 655 };
 656
 657 &usb_1 {
 658         /* We'll use this as USB 2.0 only */
 659         qcom,select-utmi-as-pipe-clk;
 660         status = "okay";
 661 };
 662
 663 &usb_1_dwc3 {
 664         dr_mode = "peripheral";
 665
 666         /* Fastest mode for USB 2 */
 667         maximum-speed = "high-speed";
 668
 669         /* Remove USB3 phy */
 670         phys = <&usb_1_hsphy>;
 671         phy-names = "usb2-phy";
 672 };
 673
 674 &usb_1_hsphy {
 675         vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
 676         vdda-pll-supply = <&vreg_l12a_1p8>;
 677         vdd-supply = <&vreg_l1a_0p875>;
 678
 679         qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
 680         qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_5_PERCENT>;
 681         qcom,hstx-trim-value = <QUSB2_V2_HSTX_TRIM_21_6_MA>;
 682         qcom,imp-res-offset-value = <8>;
 683
 684         status = "okay";
 685 };
 686
 687 &usb_1_qmpphy {
 688         vdda-pll-supply = <&vreg_l1a_0p875>;
 689         vdda-phy-supply = <&vreg_l26a_1p2>;
 690         status = "okay";
 691 };
 692
 693 &ufs_mem_hc {
 694         reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
 695         vcc-supply = <&vreg_l20a_2p95>;
 696         vcc-max-microamp = <800000>;
 697         status = "okay";
 698 };
 699
 700 &ufs_mem_phy {
 701         vdda-phy-supply = <&vdda_ufs1_core>;
 702         vdda-pll-supply = <&vdda_ufs1_1p2>;
 703         status = "okay";
 704 };
 705
 706 &venus {
 707         firmware-name = "/*(DEBLOBBED)*/";
 708         status = "okay";
 709 };
 710
 711 &wcd9340 {
 712         pinctrl-0 = <&wcd_intr_default>;
 713         pinctrl-names = "default";
 714         clock-names = "extclk";
 715         clocks = <&rpmhcc RPMH_LN_BB_CLK2>;
 716         reset-gpios = <&tlmm 64 GPIO_ACTIVE_HIGH>;
 717         vdd-buck-sido-supply = <&vreg_s4a_1p8>;
 718         vdd-buck-supply = <&vreg_s4a_1p8>;
 719         vdd-tx-supply = <&vreg_s4a_1p8>;
 720         vdd-rx-supply = <&vreg_s4a_1p8>;
 721         vdd-io-supply = <&vreg_s4a_1p8>;
 722
 723         qcom,micbias1-microvolt = <2700000>;
 724         qcom,micbias2-microvolt = <1800000>;
 725         qcom,micbias3-microvolt = <2700000>;
 726         qcom,micbias4-microvolt = <2700000>;
 727 };
 728
 729 &wifi {
 730         vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>;
 731         vdd-1.8-xo-supply = <&vreg_l7a_1p8>;
 732         vdd-1.3-rfa-supply = <&vreg_l17a_1p3>;
 733         vdd-3.3-ch0-supply = <&vreg_l25a_3p3>;
 734         vdd-3.3-ch1-supply = <&vreg_l23a_3p3>;
 735         status = "okay";
 736 };
 737
 738 /* PINCTRL - additions to nodes defined in sdm845.dtsi */
 739
 740 &qup_uart6_default {
 741         pinmux {
 742                  pins = "gpio45", "gpio46", "gpio47", "gpio48";
 743                  function = "qup6";
 744         };
 745
 746         cts {
 747                 pins = "gpio45";
 748                 bias-disable;
 749         };
 750
 751         rts-tx {
 752                 pins = "gpio46", "gpio47";
 753                 drive-strength = <2>;
 754                 bias-disable;
 755         };
 756
 757         rx {
 758                 pins = "gpio48";
 759                 bias-pull-up;
 760         };
 761 };