arch/arm64/boot/dts/qcom/sdm632-fairphone-fp3.dts

   1 // SPDX-License-Identifier: BSD-3-Clause
   2 /*
   3  * Copyright (c) 2022, Luca Weiss <luca@z3ntu.xyz>
   4  */
   5 /dts-v1/;
   6
   7 #include <dt-bindings/leds/common.h>
   8 #include "sdm632.dtsi"
   9 #include "pm8953.dtsi"
  10 #include "pmi632.dtsi"
  11
  12 / {
  13         model = "Fairphone 3";
  14         compatible = "fairphone,fp3", "qcom,sdm632";
  15         chassis-type = "handset";
  16         qcom,msm-id = <349 0>;
  17         qcom,board-id = <8 0x10000>;
  18
  19         aliases {
  20                 mmc0 = &sdhc_1;
  21                 mmc1 = &sdhc_2;
  22                 serial0 = &uart_0;
  23         };
  24
  25         chosen {
  26                 stdout-path = "serial0:115200n8";
  27         };
  28
  29         gpio-keys {
  30                 compatible = "gpio-keys";
  31
  32                 key-volume-up {
  33                         label = "volume_up";
  34                         linux,code = <KEY_VOLUMEUP>;
  35                         gpios = <&tlmm 85 GPIO_ACTIVE_LOW>;
  36                 };
  37         };
  38
  39         vph_pwr: vph-pwr-regulator {
  40                 compatible = "regulator-fixed";
  41                 regulator-name = "vph_pwr";
  42                 regulator-always-on;
  43                 regulator-boot-on;
  44         };
  45 };
  46
  47 &hsusb_phy {
  48         status = "okay";
  49         vdd-supply = <&pm8953_l3>;
  50         vdda-pll-supply = <&pm8953_l7>;
  51         vdda-phy-dpdm-supply = <&pm8953_l13>;
  52 };
  53
  54 &i2c_3 {
  55         status = "okay";
  56
  57         touchscreen@48 {
  58                 compatible = "himax,hx83112b";
  59                 reg = <0x48>;
  60                 interrupt-parent = <&tlmm>;
  61                 interrupts = <65 IRQ_TYPE_LEVEL_LOW>;
  62                 touchscreen-size-x = <1080>;
  63                 touchscreen-size-y = <2160>;
  64                 reset-gpios = <&tlmm 64 GPIO_ACTIVE_LOW>;
  65         };
  66 };
  67
  68 &i2c_5 {
  69         status = "okay";
  70
  71         nfc@28 {
  72                 compatible = "nxp,nq310", "nxp,nxp-nci-i2c";
  73                 reg = <0x28>;
  74
  75                 interrupt-parent = <&tlmm>;
  76                 interrupts = <17 IRQ_TYPE_LEVEL_HIGH>;
  77
  78                 enable-gpios = <&tlmm 16 GPIO_ACTIVE_HIGH>;
  79                 firmware-gpios = <&tlmm 62 GPIO_ACTIVE_HIGH>;
  80         };
  81 };
  82
  83 &pm8953_resin {
  84         status = "okay";
  85         linux,code = <KEY_VOLUMEDOWN>;
  86 };
  87
  88 &pmi632_lpg {
  89         status = "okay";
  90
  91         multi-led {
  92                 color = <LED_COLOR_ID_RGB>;
  93                 function = LED_FUNCTION_STATUS;
  94
  95                 #address-cells = <1>;
  96                 #size-cells = <0>;
  97
  98                 led@1 {
  99                         reg = <1>;
 100                         color = <LED_COLOR_ID_RED>;
 101                 };
 102
 103                 led@2 {
 104                         reg = <2>;
 105                         color = <LED_COLOR_ID_GREEN>;
 106                 };
 107
 108                 led@3 {
 109                         reg = <3>;
 110                         color = <LED_COLOR_ID_BLUE>;
 111                 };
 112         };
 113 };
 114
 115 &sdhc_1 {
 116         status = "okay";
 117         vmmc-supply = <&pm8953_l8>;
 118         vqmmc-supply = <&pm8953_l5>;
 119 };
 120
 121 &sdhc_2 {
 122         status = "okay";
 123         vmmc-supply = <&pm8953_l11>;
 124         vqmmc-supply = <&pm8953_l12>;
 125
 126         cd-gpios = <&tlmm 133 GPIO_ACTIVE_LOW>;
 127 };
 128
 129 &rpm_requests {
 130         regulators {
 131                 compatible = "qcom,rpm-pm8953-regulators";
 132
 133                 vdd_l1-supply = <&pm8953_s3>;
 134                 vdd_l2_l3-supply = <&pm8953_s3>;
 135                 vdd_l4_l5_l6_l7_l16_l19-supply = <&pm8953_s4>;
 136                 vdd_l8_l11_l12_l13_l14_l15-supply = <&vph_pwr>;
 137                 vdd_l9_l10_l17_l18_l22-supply = <&vph_pwr>;
 138
 139                 pm8953_s3: s3 {
 140                         regulator-min-microvolt = <984000>;
 141                         regulator-max-microvolt = <1240000>;
 142                 };
 143                 pm8953_s4: s4 {
 144                         regulator-min-microvolt = <1036000>;
 145                         regulator-max-microvolt = <2040000>;
 146                 };
 147                 pm8953_s5: s5 {
 148                         regulator-min-microvolt = <1036000>;
 149                         regulator-max-microvolt = <2040000>;
 150                 };
 151
 152                 pm8953_l1: l1 {
 153                         regulator-min-microvolt = <975000>;
 154                         regulator-max-microvolt = <1050000>;
 155                 };
 156                 pm8953_l2: l2 {
 157                         regulator-min-microvolt = <975000>;
 158                         regulator-max-microvolt = <1175000>;
 159                 };
 160                 pm8953_l3: l3 {
 161                         regulator-min-microvolt = <925000>;
 162                         regulator-max-microvolt = <925000>;
 163                 };
 164                 pm8953_l5: l5 {
 165                         regulator-min-microvolt = <1800000>;
 166                         regulator-max-microvolt = <1800000>;
 167                 };
 168                 pm8953_l6: l6 {
 169                         regulator-min-microvolt = <1800000>;
 170                         regulator-max-microvolt = <1800000>;
 171                 };
 172                 pm8953_l7: l7 {
 173                         regulator-min-microvolt = <1800000>;
 174                         regulator-max-microvolt = <1900000>;
 175                 };
 176                 pm8953_l8: l8 {
 177                         regulator-min-microvolt = <2900000>;
 178                         regulator-max-microvolt = <2900000>;
 179                 };
 180                 pm8953_l9: l9 {
 181                         regulator-min-microvolt = <3000000>;
 182                         regulator-max-microvolt = <3300000>;
 183                 };
 184                 pm8953_l10: l10 {
 185                         regulator-min-microvolt = <2800000>;
 186                         regulator-max-microvolt = <3000000>;
 187                 };
 188                 pm8953_l11: l11 {
 189                         regulator-min-microvolt = <2950000>;
 190                         regulator-max-microvolt = <2950000>;
 191                 };
 192                 pm8953_l12: l12 {
 193                         regulator-min-microvolt = <1800000>;
 194                         regulator-max-microvolt = <2950000>;
 195                 };
 196                 pm8953_l13: l13 {
 197                         regulator-min-microvolt = <3125000>;
 198                         regulator-max-microvolt = <3125000>;
 199                 };
 200                 pm8953_l16: l16 {
 201                         regulator-min-microvolt = <1800000>;
 202                         regulator-max-microvolt = <1800000>;
 203                 };
 204                 pm8953_l17: l17 {
 205                         regulator-min-microvolt = <2850000>;
 206                         regulator-max-microvolt = <2850000>;
 207                 };
 208                 pm8953_l19: l19 {
 209                         regulator-min-microvolt = <1200000>;
 210                         regulator-max-microvolt = <1350000>;
 211                 };
 212                 pm8953_l22: l22 {
 213                         regulator-min-microvolt = <2800000>;
 214                         regulator-max-microvolt = <2800000>;
 215                 };
 216                 pm8953_l23: l23 {
 217                         regulator-min-microvolt = <975000>;
 218                         regulator-max-microvolt = <1225000>;
 219                 };
 220         };
 221 };
 222
 223 &tlmm {
 224         /*
 225          * 0-3: unused but protected by TZ
 226          * 135-138: fingerprint reader (SPI)
 227          */
 228         gpio-reserved-ranges = <0 4>, <135 4>;
 229 };
 230
 231 &uart_0 {
 232         status = "okay";
 233 };
 234
 235 &usb3 {
 236         status = "okay";
 237 };
 238
 239 &usb3_dwc3 {
 240         dr_mode = "peripheral";
 241 };