arch/arm64/boot/dts/qcom/sc8280xp-pmics.dtsi

   1 // SPDX-License-Identifier: BSD-3-Clause
   2 /*
   3  * Copyright (c) 2022, Linaro Limited
   4  */
   5
   6 #include <dt-bindings/input/input.h>
   7 #include <dt-bindings/interrupt-controller/irq.h>
   8 #include <dt-bindings/spmi/spmi.h>
   9
  10 / {
  11         thermal-zones {
  12                 pm8280_1_thermal: pm8280-1-thermal {
  13                         polling-delay-passive = <100>;
  14                         polling-delay = <0>;
  15                         thermal-sensors = <&pm8280_1_temp_alarm>;
  16
  17                         trips {
  18                                 trip0 {
  19                                         temperature = <95000>;
  20                                         hysteresis = <0>;
  21                                         type = "passive";
  22                                 };
  23
  24                                 trip1 {
  25                                         temperature = <115000>;
  26                                         hysteresis = <0>;
  27                                         type = "critical";
  28                                 };
  29                         };
  30                 };
  31
  32                 pm8280_2_thermal: pm8280-2-thermal {
  33                         polling-delay-passive = <100>;
  34                         polling-delay = <0>;
  35                         thermal-sensors = <&pm8280_2_temp_alarm>;
  36
  37                         trips {
  38                                 trip0 {
  39                                         temperature = <95000>;
  40                                         hysteresis = <0>;
  41                                         type = "passive";
  42                                 };
  43
  44                                 trip1 {
  45                                         temperature = <115000>;
  46                                         hysteresis = <0>;
  47                                         type = "critical";
  48                                 };
  49                         };
  50                 };
  51         };
  52 };
  53
  54 &spmi_bus {
  55         pmk8280: pmic@0 {
  56                 compatible = "qcom,pmk8350", "qcom,spmi-pmic";
  57                 reg = <0x0 SPMI_USID>;
  58                 #address-cells = <1>;
  59                 #size-cells = <0>;
  60
  61                 pmk8280_pon: pon@1300 {
  62                         compatible = "qcom,pmk8350-pon";
  63                         reg = <0x1300>, <0x800>;
  64                         reg-names = "hlos", "pbs";
  65
  66                         pmk8280_pon_pwrkey: pwrkey {
  67                                 compatible = "qcom,pmk8350-pwrkey";
  68                                 interrupts-extended = <&spmi_bus 0x0 0x13 0x7 IRQ_TYPE_EDGE_BOTH>;
  69                                 linux,code = <KEY_POWER>;
  70                                 status = "disabled";
  71                         };
  72
  73                         pmk8280_pon_resin: resin {
  74                                 compatible = "qcom,pmk8350-resin";
  75                                 interrupts-extended = <&spmi_bus 0x0 0x13 0x6 IRQ_TYPE_EDGE_BOTH>;
  76                                 status = "disabled";
  77                         };
  78                 };
  79
  80                 pmk8280_vadc: adc@3100 {
  81                         compatible = "qcom,spmi-adc7";
  82                         reg = <0x3100>;
  83                         interrupts-extended = <&spmi_bus 0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
  84                         #address-cells = <1>;
  85                         #size-cells = <0>;
  86                         #io-channel-cells = <1>;
  87                         status = "disabled";
  88                 };
  89
  90                 pmk8280_adc_tm: adc-tm@3400 {
  91                         compatible = "qcom,spmi-adc-tm5-gen2";
  92                         reg = <0x3400>;
  93                         interrupts-extended = <&spmi_bus 0x0 0x34 0x0 IRQ_TYPE_EDGE_RISING>;
  94                         #address-cells = <1>;
  95                         #size-cells = <0>;
  96                         #thermal-sensor-cells = <1>;
  97                         status = "disabled";
  98                 };
  99
 100                 pmk8280_rtc: rtc@6100 {
 101                         compatible = "qcom,pmk8350-rtc";
 102                         reg = <0x6100>, <0x6200>;
 103                         reg-names = "rtc", "alarm";
 104                         interrupts-extended = <&spmi_bus 0x0 0x62 0x1 IRQ_TYPE_EDGE_RISING>;
 105                         wakeup-source;
 106                         status = "disabled";
 107                 };
 108
 109                 pmk8280_sdam_6: nvram@8500 {
 110                         compatible = "qcom,spmi-sdam";
 111                         reg = <0x8500>;
 112                         #address-cells = <1>;
 113                         #size-cells = <1>;
 114                         ranges = <0 0x8500 0x100>;
 115                         status = "disabled";
 116                 };
 117         };
 118
 119         pmc8280_1: pmic@1 {
 120                 compatible = "qcom,pm8350", "qcom,spmi-pmic";
 121                 reg = <0x1 SPMI_USID>;
 122                 #address-cells = <1>;
 123                 #size-cells = <0>;
 124
 125                 pm8280_1_temp_alarm: temp-alarm@a00 {
 126                         compatible = "qcom,spmi-temp-alarm";
 127                         reg = <0xa00>;
 128                         interrupts-extended = <&spmi_bus 0x1 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
 129                         #thermal-sensor-cells = <0>;
 130                 };
 131
 132                 pmc8280_1_gpios: gpio@8800 {
 133                         compatible = "qcom,pm8350-gpio", "qcom,spmi-gpio";
 134                         reg = <0x8800>;
 135                         gpio-controller;
 136                         gpio-ranges = <&pmc8280_1_gpios 0 0 10>;
 137                         #gpio-cells = <2>;
 138                         interrupt-controller;
 139                         #interrupt-cells = <2>;
 140                 };
 141         };
 142
 143         pmc8280c: pmic@2 {
 144                 compatible = "qcom,pm8350c", "qcom,spmi-pmic";
 145                 reg = <0x2 SPMI_USID>;
 146                 #address-cells = <1>;
 147                 #size-cells = <0>;
 148
 149                 pmc8280c_gpios: gpio@8800 {
 150                         compatible = "qcom,pm8350c-gpio", "qcom,spmi-gpio";
 151                         reg = <0x8800>;
 152                         gpio-controller;
 153                         gpio-ranges = <&pmc8280c_gpios 0 0 9>;
 154                         #gpio-cells = <2>;
 155                         interrupt-controller;
 156                         #interrupt-cells = <2>;
 157                 };
 158
 159                 pmc8280c_lpg: pwm {
 160                         compatible = "qcom,pm8350c-pwm";
 161
 162                         #address-cells = <1>;
 163                         #size-cells = <0>;
 164
 165                         #pwm-cells = <2>;
 166
 167                         status = "disabled";
 168                 };
 169         };
 170
 171         pmc8280_2: pmic@3 {
 172                 compatible = "qcom,pm8350", "qcom,spmi-pmic";
 173                 reg = <0x3 SPMI_USID>;
 174                 #address-cells = <1>;
 175                 #size-cells = <0>;
 176
 177                 pm8280_2_temp_alarm: temp-alarm@a00 {
 178                         compatible = "qcom,spmi-temp-alarm";
 179                         reg = <0xa00>;
 180                         interrupts-extended = <&spmi_bus 0x2 0xa 0x0 IRQ_TYPE_EDGE_BOTH>;
 181                         #thermal-sensor-cells = <0>;
 182                 };
 183
 184                 pmc8280_2_gpios: gpio@8800 {
 185                         compatible = "qcom,pm8350-gpio", "qcom,spmi-gpio";
 186                         reg = <0x8800>;
 187                         gpio-controller;
 188                         gpio-ranges = <&pmc8280_2_gpios 0 0 10>;
 189                         #gpio-cells = <2>;
 190                         interrupt-controller;
 191                         #interrupt-cells = <2>;
 192                 };
 193         };
 194
 195         pmr735a: pmic@4 {
 196                 compatible = "qcom,pmr735a", "qcom,spmi-pmic";
 197                 reg = <0x4 SPMI_USID>;
 198                 #address-cells = <1>;
 199                 #size-cells = <0>;
 200
 201                 pmr735a_gpios: gpio@8800 {
 202                         compatible = "qcom,pmr735a-gpio", "qcom,spmi-gpio";
 203                         reg = <0x8800>;
 204                         gpio-controller;
 205                         gpio-ranges = <&pmr735a_gpios 0 0 4>;
 206                         #gpio-cells = <2>;
 207                         interrupt-controller;
 208                         #interrupt-cells = <2>;
 209                 };
 210         };
 211 };