arch/arm64/boot/dts/qcom/qrb5165-rb5.dts

   1 // SPDX-License-Identifier: BSD-3-Clause
   2 /*
   3  * Copyright (c) 2020, Linaro Ltd.
   4  */
   5
   6 /dts-v1/;
   7
   8 #include <dt-bindings/leds/common.h>
   9 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
  10 #include <dt-bindings/sound/qcom,q6afe.h>
  11 #include <dt-bindings/sound/qcom,q6asm.h>
  12 #include "sm8250.dtsi"
  13 #include "pm8150.dtsi"
  14 #include "pm8150b.dtsi"
  15 #include "pm8150l.dtsi"
  16
  17 / {
  18         model = "Qualcomm Technologies, Inc. Robotics RB5";
  19         compatible = "qcom,qrb5165-rb5", "qcom,sm8250";
  20         qcom,msm-id = <455 0x20001>;
  21         qcom,board-id = <11 3>;
  22
  23         aliases {
  24                 serial0 = &uart12;
  25                 sdhc2 = &sdhc_2;
  26         };
  27
  28         chosen {
  29                 stdout-path = "serial0:115200n8";
  30         };
  31
  32         /* Fixed crystal oscillator dedicated to MCP2518FD */
  33         clk40M: can-clock {
  34                 compatible = "fixed-clock";
  35                 #clock-cells = <0>;
  36                 clock-frequency = <40000000>;
  37         };
  38
  39         dc12v: dc12v-regulator {
  40                 compatible = "regulator-fixed";
  41                 regulator-name = "DC12V";
  42                 regulator-min-microvolt = <12000000>;
  43                 regulator-max-microvolt = <12000000>;
  44                 regulator-always-on;
  45         };
  46
  47         hdmi-out {
  48                 compatible = "hdmi-connector";
  49                 type = "a";
  50
  51                 port {
  52                         hdmi_con: endpoint {
  53                                 remote-endpoint = <&lt9611_out>;
  54                         };
  55                 };
  56         };
  57
  58         leds {
  59                 compatible = "gpio-leds";
  60
  61                 led-user4 {
  62                         label = "green:user4";
  63                         function = LED_FUNCTION_INDICATOR;
  64                         color = <LED_COLOR_ID_GREEN>;
  65                         gpios = <&pm8150_gpios 10 GPIO_ACTIVE_HIGH>;
  66                         default-state = "off";
  67                         panic-indicator;
  68                 };
  69
  70                 led-wlan {
  71                         label = "yellow:wlan";
  72                         function = LED_FUNCTION_WLAN;
  73                         color = <LED_COLOR_ID_YELLOW>;
  74                         gpios = <&pm8150_gpios 9 GPIO_ACTIVE_HIGH>;
  75                         linux,default-trigger = "phy0tx";
  76                         default-state = "off";
  77                 };
  78
  79                 led-bt {
  80                         label = "blue:bt";
  81                         function = LED_FUNCTION_BLUETOOTH;
  82                         color = <LED_COLOR_ID_BLUE>;
  83                         gpios = <&pm8150_gpios 7 GPIO_ACTIVE_HIGH>;
  84                         linux,default-trigger = "bluetooth-power";
  85                         default-state = "off";
  86                 };
  87         };
  88
  89         lt9611_1v2: lt9611-vdd12-regulator {
  90                 compatible = "regulator-fixed";
  91                 regulator-name = "LT9611_1V2";
  92
  93                 vin-supply = <&vdc_3v3>;
  94                 regulator-min-microvolt = <1200000>;
  95                 regulator-max-microvolt = <1200000>;
  96         };
  97
  98         lt9611_3v3: lt9611-3v3 {
  99                 compatible = "regulator-fixed";
 100                 regulator-name = "LT9611_3V3";
 101
 102                 vin-supply = <&vdc_3v3>;
 103                 regulator-min-microvolt = <3300000>;
 104                 regulator-max-microvolt = <3300000>;
 105                 regulator-boot-on;
 106                 regulator-always-on;
 107         };
 108
 109         thermal-zones {
 110                 conn-thermal {
 111                         polling-delay-passive = <0>;
 112                         polling-delay = <0>;
 113                         thermal-sensors = <&pm8150b_adc_tm 0>;
 114
 115                         trips {
 116                                 active-config0 {
 117                                         temperature = <125000>;
 118                                         hysteresis = <1000>;
 119                                         type = "critical";
 120                                 };
 121                         };
 122                 };
 123
 124                 pm8150l-pcb-thermal {
 125                         polling-delay-passive = <0>;
 126                         polling-delay = <0>;
 127                         thermal-sensors = <&pm8150l_adc_tm 1>;
 128
 129                         trips {
 130                                 active-config0 {
 131                                         temperature = <50000>;
 132                                         hysteresis = <4000>;
 133                                         type = "passive";
 134                                 };
 135                         };
 136                 };
 137
 138                 skin-msm-thermal {
 139                         polling-delay-passive = <0>;
 140                         polling-delay = <0>;
 141                         thermal-sensors = <&pm8150l_adc_tm 0>;
 142
 143                         trips {
 144                                 active-config0 {
 145                                         temperature = <50000>;
 146                                         hysteresis = <4000>;
 147                                         type = "passive";
 148                                 };
 149                         };
 150                 };
 151
 152                 wifi-thermal {
 153                         polling-delay-passive = <0>;
 154                         polling-delay = <0>;
 155                         thermal-sensors = <&pm8150_adc_tm 1>;
 156
 157                         trips {
 158                                 active-config0 {
 159                                         temperature = <52000>;
 160                                         hysteresis = <4000>;
 161                                         type = "passive";
 162                                 };
 163                         };
 164                 };
 165
 166                 xo-thermal {
 167                         polling-delay-passive = <0>;
 168                         polling-delay = <0>;
 169                         thermal-sensors = <&pm8150_adc_tm 0>;
 170
 171                         trips {
 172                                 active-config0 {
 173                                         temperature = <50000>;
 174                                         hysteresis = <4000>;
 175                                         type = "passive";
 176                                 };
 177                         };
 178                 };
 179         };
 180
 181         vbat: vbat-regulator {
 182                 compatible = "regulator-fixed";
 183                 regulator-name = "VBAT";
 184                 vin-supply = <&vreg_l11c_3p3>;
 185                 regulator-min-microvolt = <4200000>;
 186                 regulator-max-microvolt = <4200000>;
 187                 regulator-always-on;
 188         };
 189
 190         vbat_som: vbat-som-regulator {
 191                 compatible = "regulator-fixed";
 192                 regulator-name = "VBAT_SOM";
 193                 vin-supply = <&dc12v>;
 194                 regulator-min-microvolt = <4200000>;
 195                 regulator-max-microvolt = <4200000>;
 196                 regulator-always-on;
 197         };
 198
 199         vdc_3v3: vdc-3v3-regulator {
 200                 compatible = "regulator-fixed";
 201                 regulator-name = "VDC_3V3";
 202                 vin-supply = <&vreg_l11c_3p3>;
 203                 regulator-min-microvolt = <3300000>;
 204                 regulator-max-microvolt = <3300000>;
 205                 regulator-always-on;
 206         };
 207
 208         vdc_5v: vdc-5v-regulator {
 209                 compatible = "regulator-fixed";
 210                 regulator-name = "VDC_5V";
 211
 212                 regulator-min-microvolt = <5000000>;
 213                 regulator-max-microvolt = <5000000>;
 214                 regulator-always-on;
 215                 vin-supply = <&vreg_l11c_3p3>;
 216         };
 217
 218         vph_pwr: vph-pwr-regulator {
 219                 compatible = "regulator-fixed";
 220                 regulator-name = "vph_pwr";
 221                 regulator-min-microvolt = <3700000>;
 222                 regulator-max-microvolt = <3700000>;
 223                 regulator-always-on;
 224         };
 225
 226         vreg_s4a_1p8: vreg-s4a-1p8 {
 227                 compatible = "regulator-fixed";
 228                 regulator-name = "vreg_s4a_1p8";
 229                 regulator-min-microvolt = <1800000>;
 230                 regulator-max-microvolt = <1800000>;
 231                 regulator-always-on;
 232         };
 233 };
 234
 235 &adsp {
 236         status = "okay";
 237         firmware-name = "/*(DEBLOBBED)*/";
 238 };
 239
 240 &apps_rsc {
 241         pm8009-rpmh-regulators {
 242                 compatible = "qcom,pm8009-1-rpmh-regulators";
 243                 qcom,pmic-id = "f";
 244
 245                 vdd-s1-supply = <&vph_pwr>;
 246                 vdd-s2-supply = <&vph_pwr>;
 247                 vdd-l2-supply = <&vreg_s8c_1p3>;
 248                 vdd-l5-l6-supply = <&vreg_bob>;
 249                 vdd-l7-supply = <&vreg_s4a_1p8>;
 250
 251                 vreg_s2f_0p95: smps2 {
 252                         regulator-name = "vreg_s2f_0p95";
 253                         regulator-min-microvolt = <900000>;
 254                         regulator-max-microvolt = <952000>;
 255                         regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
 256                 };
 257
 258                 vreg_l1f_1p1: ldo1 {
 259                         regulator-name = "vreg_l1f_1p1";
 260                         regulator-min-microvolt = <1104000>;
 261                         regulator-max-microvolt = <1104000>;
 262                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 263                 };
 264
 265                 vreg_l2f_1p2: ldo2 {
 266                         regulator-name = "vreg_l2f_1p2";
 267                         regulator-min-microvolt = <1200000>;
 268                         regulator-max-microvolt = <1200000>;
 269                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 270                 };
 271
 272                 vreg_l6f_2p8: ldo6 {
 273                         regulator-name = "vreg_l6f_2p8";
 274                         regulator-min-microvolt = <2800000>;
 275                         regulator-max-microvolt = <2800000>;
 276                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 277                 };
 278
 279                 vreg_l7f_1p8: ldo7 {
 280                         regulator-name = "vreg_l7f_1p8";
 281                         regulator-min-microvolt = <1800000>;
 282                         regulator-max-microvolt = <1800000>;
 283                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 284                 };
 285         };
 286
 287         pm8150-rpmh-regulators {
 288                 compatible = "qcom,pm8150-rpmh-regulators";
 289                 qcom,pmic-id = "a";
 290
 291                 vdd-s1-supply = <&vph_pwr>;
 292                 vdd-s2-supply = <&vph_pwr>;
 293                 vdd-s3-supply = <&vph_pwr>;
 294                 vdd-s4-supply = <&vph_pwr>;
 295                 vdd-s5-supply = <&vph_pwr>;
 296                 vdd-s6-supply = <&vph_pwr>;
 297                 vdd-s7-supply = <&vph_pwr>;
 298                 vdd-s8-supply = <&vph_pwr>;
 299                 vdd-s9-supply = <&vph_pwr>;
 300                 vdd-s10-supply = <&vph_pwr>;
 301                 vdd-l2-l10-supply = <&vreg_bob>;
 302                 vdd-l3-l4-l5-l18-supply = <&vreg_s6a_0p95>;
 303                 vdd-l6-l9-supply = <&vreg_s8c_1p3>;
 304                 vdd-l7-l12-l14-l15-supply = <&vreg_s5a_1p9>;
 305                 vdd-l13-l16-l17-supply = <&vreg_bob>;
 306
 307                 vreg_l2a_3p1: ldo2 {
 308                         regulator-name = "vreg_l2a_3p1";
 309                         regulator-min-microvolt = <3072000>;
 310                         regulator-max-microvolt = <3072000>;
 311                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 312                 };
 313
 314                 vreg_l3a_0p9: ldo3 {
 315                         regulator-name = "vreg_l3a_0p9";
 316                         regulator-min-microvolt = <928000>;
 317                         regulator-max-microvolt = <932000>;
 318                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 319                 };
 320
 321                 vreg_l5a_0p88: ldo5 {
 322                         regulator-name = "vreg_l5a_0p88";
 323                         regulator-min-microvolt = <880000>;
 324                         regulator-max-microvolt = <880000>;
 325                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 326                 };
 327
 328                 vreg_l6a_1p2: ldo6 {
 329                         regulator-name = "vreg_l6a_1p2";
 330                         regulator-min-microvolt = <1200000>;
 331                         regulator-max-microvolt = <1200000>;
 332                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 333                 };
 334
 335                 vreg_l7a_1p7: ldo7 {
 336                         regulator-name = "vreg_l7a_1p7";
 337                         regulator-min-microvolt = <1704000>;
 338                         regulator-max-microvolt = <1800000>;
 339                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 340                 };
 341
 342                 vreg_l9a_1p2: ldo9 {
 343                         regulator-name = "vreg_l9a_1p2";
 344                         regulator-min-microvolt = <1200000>;
 345                         regulator-max-microvolt = <1200000>;
 346                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 347                 };
 348
 349                 vreg_l10a_1p8: ldo10 {
 350                         regulator-name = "vreg_l10a_1p8";
 351                         regulator-min-microvolt = <1800000>;
 352                         regulator-max-microvolt = <1800000>;
 353                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 354                 };
 355
 356                 vreg_l12a_1p8: ldo12 {
 357                         regulator-name = "vreg_l12a_1p8";
 358                         regulator-min-microvolt = <1800000>;
 359                         regulator-max-microvolt = <1800000>;
 360                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 361                 };
 362
 363                 vreg_l13a_ts_3p0: ldo13 {
 364                         regulator-name = "vreg_l13a_ts_3p0";
 365                         regulator-min-microvolt = <3008000>;
 366                         regulator-max-microvolt = <3008000>;
 367                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 368                 };
 369
 370                 vreg_l14a_1p8: ldo14 {
 371                         regulator-name = "vreg_l14a_1p8";
 372                         regulator-min-microvolt = <1800000>;
 373                         regulator-max-microvolt = <1880000>;
 374                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 375                 };
 376
 377                 vreg_l15a_1p8: ldo15 {
 378                         regulator-name = "vreg_l15a_1p8";
 379                         regulator-min-microvolt = <1800000>;
 380                         regulator-max-microvolt = <1800000>;
 381                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 382                 };
 383
 384                 vreg_l16a_2p7: ldo16 {
 385                         regulator-name = "vreg_l16a_2p7";
 386                         regulator-min-microvolt = <2704000>;
 387                         regulator-max-microvolt = <2960000>;
 388                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 389                 };
 390
 391                 vreg_l17a_3p0: ldo17 {
 392                         regulator-name = "vreg_l17a_3p0";
 393                         regulator-min-microvolt = <2856000>;
 394                         regulator-max-microvolt = <3008000>;
 395                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 396                 };
 397
 398                 vreg_l18a_0p92: ldo18 {
 399                         regulator-name = "vreg_l18a_0p92";
 400                         regulator-min-microvolt = <800000>;
 401                         regulator-max-microvolt = <912000>;
 402                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 403                 };
 404
 405                 vreg_s5a_1p9: smps5 {
 406                         regulator-name = "vreg_s5a_1p9";
 407                         regulator-min-microvolt = <1904000>;
 408                         regulator-max-microvolt = <2000000>;
 409                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 410                 };
 411
 412                 vreg_s6a_0p95: smps6 {
 413                         regulator-name = "vreg_s6a_0p95";
 414                         regulator-min-microvolt = <920000>;
 415                         regulator-max-microvolt = <1128000>;
 416                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 417                 };
 418         };
 419
 420         pm8150l-rpmh-regulators {
 421                 compatible = "qcom,pm8150l-rpmh-regulators";
 422                 qcom,pmic-id = "c";
 423
 424                 vdd-s1-supply = <&vph_pwr>;
 425                 vdd-s2-supply = <&vph_pwr>;
 426                 vdd-s3-supply = <&vph_pwr>;
 427                 vdd-s4-supply = <&vph_pwr>;
 428                 vdd-s5-supply = <&vph_pwr>;
 429                 vdd-s6-supply = <&vph_pwr>;
 430                 vdd-s7-supply = <&vph_pwr>;
 431                 vdd-s8-supply = <&vph_pwr>;
 432                 vdd-l1-l8-supply = <&vreg_s4a_1p8>;
 433                 vdd-l2-l3-supply = <&vreg_s8c_1p3>;
 434                 vdd-l4-l5-l6-supply = <&vreg_bob>;
 435                 vdd-l7-l11-supply = <&vreg_bob>;
 436                 vdd-l9-l10-supply = <&vreg_bob>;
 437                 vdd-bob-supply = <&vph_pwr>;
 438
 439                 vreg_bob: bob {
 440                         regulator-name = "vreg_bob";
 441                         regulator-min-microvolt = <3008000>;
 442                         regulator-max-microvolt = <4000000>;
 443                         regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
 444                 };
 445
 446                 vreg_l1c_1p8: ldo1 {
 447                         regulator-name = "vreg_l1c_1p8";
 448                         regulator-min-microvolt = <1800000>;
 449                         regulator-max-microvolt = <1800000>;
 450                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 451                 };
 452
 453                 vreg_l2c_1p2: ldo2 {
 454                         regulator-name = "vreg_l2c_1p2";
 455                         regulator-min-microvolt = <1200000>;
 456                         regulator-max-microvolt = <1200000>;
 457                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 458                 };
 459
 460                 vreg_l3c_0p8: ldo3 {
 461                         regulator-name = "vreg_l3c_0p8";
 462                         regulator-min-microvolt = <800000>;
 463                         regulator-max-microvolt = <800000>;
 464                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 465                 };
 466
 467                 vreg_l4c_1p7: ldo4 {
 468                         regulator-name = "vreg_l4c_1p7";
 469                         regulator-min-microvolt = <1704000>;
 470                         regulator-max-microvolt = <2928000>;
 471                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 472                 };
 473
 474                 vreg_l5c_1p8: ldo5 {
 475                         regulator-name = "vreg_l5c_1p8";
 476                         regulator-min-microvolt = <1800000>;
 477                         regulator-max-microvolt = <2928000>;
 478                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 479                 };
 480
 481                 vreg_l6c_2p96: ldo6 {
 482                         regulator-name = "vreg_l6c_2p96";
 483                         regulator-min-microvolt = <1800000>;
 484                         regulator-max-microvolt = <2960000>;
 485                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 486                 };
 487
 488                 vreg_l7c_cam_vcm0_2p85: ldo7 {
 489                         regulator-name = "vreg_l7c_cam_vcm0_2p85";
 490                         regulator-min-microvolt = <2856000>;
 491                         regulator-max-microvolt = <3104000>;
 492                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 493                 };
 494
 495                 vreg_l8c_1p8: ldo8 {
 496                         regulator-name = "vreg_l8c_1p8";
 497                         regulator-min-microvolt = <1800000>;
 498                         regulator-max-microvolt = <1800000>;
 499                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 500                 };
 501
 502                 vreg_l9c_2p96: ldo9 {
 503                         regulator-name = "vreg_l9c_2p96";
 504                         regulator-min-microvolt = <2704000>;
 505                         regulator-max-microvolt = <2960000>;
 506                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 507                 };
 508
 509                 vreg_l10c_3p0: ldo10 {
 510                         regulator-name = "vreg_l10c_3p0";
 511                         regulator-min-microvolt = <3000000>;
 512                         regulator-max-microvolt = <3000000>;
 513                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 514                 };
 515
 516                 vreg_l11c_3p3: ldo11 {
 517                         regulator-name = "vreg_l11c_3p3";
 518                         regulator-min-microvolt = <3296000>;
 519                         regulator-max-microvolt = <3296000>;
 520                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 521                         regulator-always-on;
 522                 };
 523
 524                 vreg_s8c_1p3: smps8 {
 525                         regulator-name = "vreg_s8c_1p3";
 526                         regulator-min-microvolt = <1352000>;
 527                         regulator-max-microvolt = <1352000>;
 528                         regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
 529                 };
 530         };
 531 };
 532
 533 &cdsp {
 534         status = "okay";
 535         firmware-name = "/*(DEBLOBBED)*/";
 536 };
 537
 538 &dsi0 {
 539         status = "okay";
 540         vdda-supply = <&vreg_l9a_1p2>;
 541
 542 #if 0
 543         qcom,dual-dsi-mode;
 544         qcom,master-dsi;
 545 #endif
 546
 547         ports {
 548                 port@1 {
 549                         endpoint {
 550                                 remote-endpoint = <&lt9611_a>;
 551                                 data-lanes = <0 1 2 3>;
 552                         };
 553                 };
 554         };
 555 };
 556
 557 &dsi0_phy {
 558         status = "okay";
 559         vdds-supply = <&vreg_l5a_0p88>;
 560 };
 561
 562 &gmu {
 563         status = "okay";
 564 };
 565
 566 &gpu {
 567         status = "okay";
 568
 569         zap-shader {
 570                 memory-region = <&gpu_mem>;
 571                 firmware-name = "/*(DEBLOBBED)*/";
 572         };
 573 };
 574
 575 /* LS-I2C0 */
 576 &i2c4 {
 577         status = "okay";
 578 };
 579
 580 &i2c5 {
 581         status = "okay";
 582         clock-frequency = <400000>;
 583
 584         lt9611_codec: hdmi-bridge@2b {
 585                 compatible = "lontium,lt9611uxc";
 586                 reg = <0x2b>;
 587                 #sound-dai-cells = <1>;
 588
 589                 interrupts-extended = <&tlmm 63 IRQ_TYPE_EDGE_FALLING>;
 590
 591                 reset-gpios = <&pm8150l_gpios 5 GPIO_ACTIVE_HIGH>;
 592
 593                 vdd-supply = <&lt9611_1v2>;
 594                 vcc-supply = <&lt9611_3v3>;
 595
 596                 pinctrl-names = "default";
 597                 pinctrl-0 = <&lt9611_irq_pin &lt9611_rst_pin>;
 598
 599                 ports {
 600                         #address-cells = <1>;
 601                         #size-cells = <0>;
 602
 603                         port@0 {
 604                                 reg = <0>;
 605
 606                                 lt9611_a: endpoint {
 607                                         remote-endpoint = <&dsi0_out>;
 608                                 };
 609                         };
 610
 611 #if 0
 612                         port@1 {
 613                                 reg = <1>;
 614
 615                                 lt9611_b: endpoint {
 616                                         remote-endpoint = <&dsi1_out>;
 617                                 };
 618                         };
 619 #endif
 620
 621                         port@2 {
 622                                 reg = <2>;
 623
 624                                 lt9611_out: endpoint {
 625                                         remote-endpoint = <&hdmi_con>;
 626                                 };
 627                         };
 628
 629                 };
 630         };
 631 };
 632
 633 /* LS-I2C1 */
 634 &i2c15 {
 635         status = "okay";
 636 };
 637
 638 &mdss {
 639         status = "okay";
 640 };
 641
 642 &mdss_mdp {
 643         status = "okay";
 644 };
 645
 646 &pm8150_adc {
 647         xo-therm@4c {
 648                 reg = <ADC5_XO_THERM_100K_PU>;
 649                 qcom,ratiometric;
 650                 qcom,hw-settle-time = <200>;
 651         };
 652
 653         wifi-therm@4e {
 654                 reg = <ADC5_AMUX_THM2_100K_PU>;
 655                 qcom,ratiometric;
 656                 qcom,hw-settle-time = <200>;
 657         };
 658 };
 659
 660 &pm8150_adc_tm {
 661         status = "okay";
 662
 663         xo-therm@0 {
 664                 reg = <0>;
 665                 io-channels = <&pm8150_adc ADC5_XO_THERM_100K_PU>;
 666                 qcom,ratiometric;
 667                 qcom,hw-settle-time-us = <200>;
 668         };
 669
 670         wifi-therm@1 {
 671                 reg = <1>;
 672                 io-channels = <&pm8150_adc ADC5_AMUX_THM2_100K_PU>;
 673                 qcom,ratiometric;
 674                 qcom,hw-settle-time-us = <200>;
 675         };
 676 };
 677
 678 &pcie0 {
 679         status = "okay";
 680 };
 681
 682 &pcie0_phy {
 683         status = "okay";
 684         vdda-phy-supply = <&vreg_l5a_0p88>;
 685         vdda-pll-supply = <&vreg_l9a_1p2>;
 686 };
 687
 688 &pcie1 {
 689         status = "okay";
 690 };
 691
 692 &pcie1_phy {
 693         status = "okay";
 694         vdda-phy-supply = <&vreg_l5a_0p88>;
 695         vdda-pll-supply = <&vreg_l9a_1p2>;
 696 };
 697
 698 &pcie2 {
 699         status = "okay";
 700 };
 701
 702 &pcie2_phy {
 703         status = "okay";
 704         vdda-phy-supply = <&vreg_l5a_0p88>;
 705         vdda-pll-supply = <&vreg_l9a_1p2>;
 706 };
 707
 708 &pm8150_gpios {
 709         gpio-reserved-ranges = <1 1>, <3 2>, <7 1>;
 710         gpio-line-names =
 711                 "NC",
 712                 "OPTION2",
 713                 "PM_GPIO-F",
 714                 "PM_SLP_CLK_IN",
 715                 "OPTION1",
 716                 "VOL_UP_N",
 717                 "PM8250_GPIO7", /* Blue LED */
 718                 "SP_ARI_PWR_ALARM",
 719                 "GPIO_9_P", /* Yellow LED */
 720                 "GPIO_10_P"; /* Green LED */
 721 };
 722
 723 &pm8150b_adc {
 724         conn-therm@4f {
 725                 reg = <ADC5_AMUX_THM3_100K_PU>;
 726                 qcom,ratiometric;
 727                 qcom,hw-settle-time = <200>;
 728         };
 729 };
 730
 731 &pm8150b_adc_tm {
 732         status = "okay";
 733
 734         conn-therm@0 {
 735                 reg = <0>;
 736                 io-channels = <&pm8150b_adc ADC5_AMUX_THM3_100K_PU>;
 737                 qcom,ratiometric;
 738                 qcom,hw-settle-time-us = <200>;
 739         };
 740 };
 741
 742 &pm8150b_gpios {
 743         gpio-line-names =
 744                 "NC",
 745                 "NC",
 746                 "NC",
 747                 "NC",
 748                 "HAP_BOOST_EN", /* SOM */
 749                 "SMB_STAT", /* SOM */
 750                 "NC",
 751                 "NC",
 752                 "SDM_FORCE_USB_BOOT",
 753                 "NC",
 754                 "NC",
 755                 "NC";
 756 };
 757
 758 &pm8150l_adc {
 759         skin-msm-therm@4e {
 760                 reg = <ADC5_AMUX_THM2_100K_PU>;
 761                 qcom,ratiometric;
 762                 qcom,hw-settle-time = <200>;
 763         };
 764
 765         pm8150l-therm@4f {
 766                 reg = <ADC5_AMUX_THM3_100K_PU>;
 767                 qcom,ratiometric;
 768                 qcom,hw-settle-time = <200>;
 769         };
 770 };
 771
 772 &pm8150l_adc_tm {
 773         status = "okay";
 774
 775         skin-msm-therm@0 {
 776                 reg = <0>;
 777                 io-channels = <&pm8150l_adc ADC5_AMUX_THM2_100K_PU>;
 778                 qcom,ratiometric;
 779                 qcom,hw-settle-time-us = <200>;
 780         };
 781
 782         pm8150l-therm@1 {
 783                 reg = <1>;
 784                 io-channels = <&pm8150l_adc ADC5_AMUX_THM3_100K_PU>;
 785                 qcom,ratiometric;
 786                 qcom,hw-settle-time-us = <200>;
 787         };
 788 };
 789
 790 &pm8150l_gpios {
 791         gpio-line-names =
 792                 "NC",
 793                 "PM3003A_EN",
 794                 "NC",
 795                 "NC",
 796                 "PM_GPIO5", /* HDMI RST_N */
 797                 "PM_GPIO-A", /* PWM */
 798                 "PM_GPIO7",
 799                 "NC",
 800                 "NC",
 801                 "PM_GPIO-B",
 802                 "NC",
 803                 "PM3003A_MODE";
 804
 805         lt9611_rst_pin: lt9611-rst-state {
 806                 pins = "gpio5";
 807                 function = "normal";
 808
 809                 output-high;
 810                 input-disable;
 811                 power-source = <0>;
 812         };
 813 };
 814
 815 &pm8150l_lpg {
 816         status = "okay";
 817
 818         #address-cells = <1>;
 819         #size-cells = <0>;
 820
 821         led@1 {
 822                 reg = <1>;
 823                 color = <LED_COLOR_ID_GREEN>;
 824                 function = LED_FUNCTION_HEARTBEAT;
 825                 function-enumerator = <3>;
 826
 827                 linux,default-trigger = "heartbeat";
 828                 default-state = "on";
 829         };
 830
 831         led@2 {
 832                 reg = <2>;
 833                 color = <LED_COLOR_ID_GREEN>;
 834                 function = LED_FUNCTION_INDICATOR;
 835                 function-enumerator = <2>;
 836                 default-state = "on";
 837         };
 838
 839         led@3 {
 840                 reg = <3>;
 841                 color = <LED_COLOR_ID_GREEN>;
 842                 function = LED_FUNCTION_INDICATOR;
 843                 function-enumerator = <1>;
 844         };
 845 };
 846
 847 &pon_pwrkey {
 848         status = "okay";
 849 };
 850
 851 &pon_resin {
 852         status = "okay";
 853
 854         linux,code = <KEY_VOLUMEDOWN>;
 855 };
 856
 857 &qupv3_id_0 {
 858         status = "okay";
 859 };
 860
 861 &qupv3_id_1 {
 862         status = "okay";
 863 };
 864
 865 &qupv3_id_2 {
 866         status = "okay";
 867 };
 868
 869 &q6afedai {
 870         qi2s@16 {
 871                 reg = <PRIMARY_MI2S_RX>;
 872                 qcom,sd-lines = <0 1 2 3>;
 873         };
 874 };
 875
 876 /* TERT I2S Uses 1 I2S SD Lines for audio on LT9611 HDMI Bridge */
 877 &q6afedai {
 878         qi2s@20 {
 879                 reg = <TERTIARY_MI2S_RX>;
 880                 qcom,sd-lines = <0>;
 881         };
 882 };
 883
 884 &q6asmdai {
 885         dai@0 {
 886                 reg = <0>;
 887         };
 888
 889         dai@1 {
 890                 reg = <1>;
 891         };
 892
 893         dai@2 {
 894                 reg = <2>;
 895         };
 896 };
 897
 898 &sdhc_2 {
 899         status = "okay";
 900         pinctrl-names = "default";
 901         pinctrl-0 = <&sdc2_default_state &sdc2_card_det_n>;
 902         vmmc-supply = <&vreg_l9c_2p96>;
 903         vqmmc-supply = <&vreg_l6c_2p96>;
 904         cd-gpios = <&tlmm 77 GPIO_ACTIVE_LOW>;
 905         bus-width = <4>;
 906         no-sdio;
 907         no-emmc;
 908 };
 909
 910 &sound {
 911         compatible = "qcom,qrb5165-rb5-sndcard";
 912         pinctrl-0 = <&tert_mi2s_active>;
 913         pinctrl-names = "default";
 914         model = "Qualcomm-RB5-WSA8815-Speakers-DMIC0";
 915         audio-routing =
 916                 "SpkrLeft IN", "WSA_SPK1 OUT",
 917                 "SpkrRight IN", "WSA_SPK2 OUT",
 918                 "VA DMIC0", "vdd-micb",
 919                 "VA DMIC1", "vdd-micb",
 920                 "MM_DL1",  "MultiMedia1 Playback",
 921                 "MM_DL2",  "MultiMedia2 Playback",
 922                 "MultiMedia3 Capture", "MM_UL3";
 923
 924         mm1-dai-link {
 925                 link-name = "MultiMedia1";
 926                 cpu {
 927                         sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA1>;
 928                 };
 929         };
 930
 931         mm2-dai-link {
 932                 link-name = "MultiMedia2";
 933                 cpu {
 934                         sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA2>;
 935                 };
 936         };
 937
 938         mm3-dai-link {
 939                 link-name = "MultiMedia3";
 940                 cpu {
 941                         sound-dai = <&q6asmdai  MSM_FRONTEND_DAI_MULTIMEDIA3>;
 942                 };
 943         };
 944
 945         hdmi-dai-link {
 946                 link-name = "HDMI Playback";
 947                 cpu {
 948                         sound-dai = <&q6afedai TERTIARY_MI2S_RX>;
 949                 };
 950
 951                 platform {
 952                         sound-dai = <&q6routing>;
 953                 };
 954
 955                 codec {
 956                         sound-dai = <&lt9611_codec 0>;
 957                 };
 958         };
 959
 960         dma-dai-link {
 961                 link-name = "WSA Playback";
 962                 cpu {
 963                         sound-dai = <&q6afedai WSA_CODEC_DMA_RX_0>;
 964                 };
 965
 966                 platform {
 967                         sound-dai = <&q6routing>;
 968                 };
 969
 970                 codec {
 971                         sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&wsamacro 0>;
 972                 };
 973         };
 974
 975         va-dai-link {
 976                 link-name = "VA Capture";
 977                 cpu {
 978                         sound-dai = <&q6afedai VA_CODEC_DMA_TX_0>;
 979                 };
 980
 981                 platform {
 982                         sound-dai = <&q6routing>;
 983                 };
 984
 985                 codec {
 986                         sound-dai = <&vamacro 0>;
 987                 };
 988         };
 989 };
 990
 991 /* CAN */
 992 &spi0 {
 993         status = "okay";
 994         pinctrl-names = "default";
 995         pinctrl-0 = <&qup_spi0_data_clk>, <&qup_spi0_cs_gpio>;
 996         cs-gpios = <&tlmm 31 GPIO_ACTIVE_LOW>;
 997
 998         can@0 {
 999                 compatible = "microchip,mcp2518fd";
1000                 reg = <0>;
1001                 clocks = <&clk40M>;
1002                 interrupts-extended = <&tlmm 15 IRQ_TYPE_LEVEL_LOW>;
1003                 spi-max-frequency = <10000000>;
1004                 vdd-supply = <&vdc_5v>;
1005                 xceiver-supply = <&vdc_5v>;
1006         };
1007 };
1008
1009 &swr0 {
1010         left_spkr: wsa8810-left{
1011                 compatible = "sdw10217211000";
1012                 reg = <0 3>;
1013                 powerdown-gpios = <&tlmm 130 GPIO_ACTIVE_HIGH>;
1014                 #thermal-sensor-cells = <0>;
1015                 sound-name-prefix = "SpkrLeft";
1016                 #sound-dai-cells = <0>;
1017         };
1018
1019         right_spkr: wsa8810-right{
1020                 compatible = "sdw10217211000";
1021                 reg = <0 4>;
1022                 powerdown-gpios = <&tlmm 130 GPIO_ACTIVE_HIGH>;
1023                 #thermal-sensor-cells = <0>;
1024                 sound-name-prefix = "SpkrRight";
1025                 #sound-dai-cells = <0>;
1026         };
1027 };
1028
1029 &tlmm {
1030         gpio-reserved-ranges = <40 4>;
1031         gpio-line-names =
1032                 "GPIO-MM",
1033                 "GPIO-NN",
1034                 "GPIO-OO",
1035                 "GPIO-PP",
1036                 "GPIO-A",
1037                 "GPIO-C",
1038                 "GPIO-E",
1039                 "GPIO-D",
1040                 "I2C0-SDA",
1041                 "I2C0-SCL",
1042                 "GPIO-TT", /* GPIO_10 */
1043                 "NC",
1044                 "GPIO_12_I2C_SDA",
1045                 "GPIO_13_I2C_SCL",
1046                 "GPIO-X",
1047                 "GPIO_15_RGMII_INT",
1048                 "HST_BT_UART_CTS",
1049                 "HST_BT_UART_RFR",
1050                 "HST_BT_UART_TX",
1051                 "HST_BT_UART_RX",
1052                 "HST_WLAN_EN", /* GPIO_20 */
1053                 "HST_BT_EN",
1054                 "GPIO-AAA",
1055                 "GPIO-BBB",
1056                 "GPIO-CCC",
1057                 "GPIO-Z",
1058                 "GPIO-DDD",
1059                 "GPIO-BB",
1060                 "GPIO_28_CAN_SPI_MISO",
1061                 "GPIO_29_CAN_SPI_MOSI",
1062                 "GPIO_30_CAN_SPI_CLK", /* GPIO_30 */
1063                 "GPIO_31_CAN_SPI_CS",
1064                 "GPIO-UU",
1065                 "NC",
1066                 "UART1_TXD_SOM",
1067                 "UART1_RXD_SOM",
1068                 "UART0_CTS",
1069                 "UART0_RTS",
1070                 "UART0_TXD",
1071                 "UART0_RXD",
1072                 "SPI1_MISO", /* GPIO_40 */
1073                 "SPI1_MOSI",
1074                 "SPI1_CLK",
1075                 "SPI1_CS",
1076                 "I2C1_SDA",
1077                 "I2C1_SCL",
1078                 "GPIO-F",
1079                 "GPIO-JJ",
1080                 "Board_ID1",
1081                 "Board_ID2",
1082                 "NC", /* GPIO_50 */
1083                 "NC",
1084                 "SPI0_MISO",
1085                 "SPI0_MOSI",
1086                 "SPI0_SCLK",
1087                 "SPI0_CS",
1088                 "GPIO-QQ",
1089                 "GPIO-RR",
1090                 "USB2LAN_RESET",
1091                 "USB2LAN_EXTWAKE",
1092                 "NC", /* GPIO_60 */
1093                 "NC",
1094                 "NC",
1095                 "LT9611_INT",
1096                 "GPIO-AA",
1097                 "USB_CC_DIR",
1098                 "GPIO-G",
1099                 "GPIO-LL",
1100                 "USB_DP_HPD_1P8",
1101                 "NC",
1102                 "NC", /* GPIO_70 */
1103                 "SD_CMD",
1104                 "SD_DAT3",
1105                 "SD_SCLK",
1106                 "SD_DAT2",
1107                 "SD_DAT1",
1108                 "SD_DAT0", /* BOOT_CFG3 */
1109                 "SD_UFS_CARD_DET_N",
1110                 "GPIO-II",
1111                 "PCIE0_RST_N",
1112                 "PCIE0_CLK_REQ_N", /* GPIO_80 */
1113                 "PCIE0_WAKE_N",
1114                 "GPIO-CC",
1115                 "GPIO-DD",
1116                 "GPIO-EE",
1117                 "GPIO-FF",
1118                 "GPIO-GG",
1119                 "GPIO-HH",
1120                 "GPIO-VV",
1121                 "GPIO-WW",
1122                 "NC", /* GPIO_90 */
1123                 "NC",
1124                 "GPIO-K",
1125                 "GPIO-I",
1126                 "CSI0_MCLK",
1127                 "CSI1_MCLK",
1128                 "CSI2_MCLK",
1129                 "CSI3_MCLK",
1130                 "GPIO-AA", /* CSI4_MCLK */
1131                 "GPIO-BB", /* CSI5_MCLK */
1132                 "GPIO-KK", /* GPIO_100 */
1133                 "CCI_I2C_SDA0",
1134                 "CCI_I2C_SCL0",
1135                 "CCI_I2C_SDA1",
1136                 "CCI_I2C_SCL1",
1137                 "CCI_I2C_SDA2",
1138                 "CCI_I2C_SCL2",
1139                 "CCI_I2C_SDA3",
1140                 "CCI_I2C_SCL3",
1141                 "GPIO-L",
1142                 "NC", /* GPIO_110 */
1143                 "NC",
1144                 "ACCEL_INT",
1145                 "GYRO_INT",
1146                 "GPIO-J",
1147                 "GPIO-YY",
1148                 "GPIO-H",
1149                 "GPIO-ZZ",
1150                 "NC",
1151                 "NC",
1152                 "NC", /* GPIO_120 */
1153                 "NC",
1154                 "MAG_INT",
1155                 "MAG_DRDY_INT",
1156                 "HST_SW_CTRL",
1157                 "GPIO-M",
1158                 "GPIO-N",
1159                 "GPIO-O",
1160                 "GPIO-P",
1161                 "PS_INT",
1162                 "WSA1_EN", /* GPIO_130 */
1163                 "USB_HUB_RESET",
1164                 "SDM_FORCE_USB_BOOT",
1165                 "I2S1_CLK_HDMI",
1166                 "I2S1_DATA0_HDMI",
1167                 "I2S1_WS_HDMI",
1168                 "GPIO-B",
1169                 "GPIO_137", /* To LT9611_I2S_MCLK_3V3 */
1170                 "PCM_CLK",
1171                 "PCM_DI",
1172                 "PCM_DO", /* GPIO_140 */
1173                 "PCM_FS",
1174                 "HST_SLIM_CLK",
1175                 "HST_SLIM_DATA",
1176                 "GPIO-U",
1177                 "GPIO-Y",
1178                 "GPIO-R",
1179                 "GPIO-Q",
1180                 "GPIO-S",
1181                 "GPIO-T",
1182                 "GPIO-V", /* GPIO_150 */
1183                 "GPIO-W",
1184                 "DMIC_CLK1",
1185                 "DMIC_DATA1",
1186                 "DMIC_CLK2",
1187                 "DMIC_DATA2",
1188                 "WSA_SWR_CLK",
1189                 "WSA_SWR_DATA",
1190                 "DMIC_CLK3",
1191                 "DMIC_DATA3",
1192                 "I2C4_SDA", /* GPIO_160 */
1193                 "I2C4_SCL",
1194                 "SPI3_CS1",
1195                 "SPI3_CS2",
1196                 "SPI2_MISO_LS3",
1197                 "SPI2_MOSI_LS3",
1198                 "SPI2_CLK_LS3",
1199                 "SPI2_ACCEL_CS_LS3",
1200                 "SPI2_CS1",
1201                 "NC",
1202                 "GPIO-SS", /* GPIO_170 */
1203                 "GPIO-XX",
1204                 "SPI3_MISO",
1205                 "SPI3_MOSI",
1206                 "SPI3_CLK",
1207                 "SPI3_CS",
1208                 "HST_BLE_SNS_UART_TX",
1209                 "HST_BLE_SNS_UART_RX",
1210                 "HST_WLAN_UART_TX",
1211                 "HST_WLAN_UART_RX";
1212
1213         lt9611_irq_pin: lt9611-irq {
1214                 pins = "gpio63";
1215                 function = "gpio";
1216                 bias-disable;
1217         };
1218
1219         sdc2_default_state: sdc2-default {
1220                 clk {
1221                         pins = "sdc2_clk";
1222                         bias-disable;
1223                         drive-strength = <16>;
1224                 };
1225
1226                 cmd {
1227                         pins = "sdc2_cmd";
1228                         bias-pull-up;
1229                         drive-strength = <10>;
1230                 };
1231
1232                 data {
1233                         pins = "sdc2_data";
1234                         bias-pull-up;
1235                         drive-strength = <10>;
1236                 };
1237         };
1238
1239         sdc2_card_det_n: sd-card-det-n {
1240                 pins = "gpio77";
1241                 function = "gpio";
1242                 bias-pull-up;
1243         };
1244 };
1245
1246 &uart12 {
1247         status = "okay";
1248 };
1249
1250 &ufs_mem_hc {
1251         status = "okay";
1252
1253         vcc-supply = <&vreg_l17a_3p0>;
1254         vcc-max-microamp = <800000>;
1255         vccq-supply = <&vreg_l6a_1p2>;
1256         vccq-max-microamp = <800000>;
1257         vccq2-supply = <&vreg_s4a_1p8>;
1258         vccq2-max-microamp = <800000>;
1259 };
1260
1261 &ufs_mem_phy {
1262         status = "okay";
1263
1264         vdda-phy-supply = <&vreg_l5a_0p88>;
1265         vdda-pll-supply = <&vreg_l9a_1p2>;
1266 };
1267
1268 &usb_1 {
1269         status = "okay";
1270 };
1271
1272 &usb_1_dwc3 {
1273         dr_mode = "peripheral";
1274 };
1275
1276 &usb_1_hsphy {
1277         status = "okay";
1278
1279         vdda-pll-supply = <&vreg_l5a_0p88>;
1280         vdda33-supply = <&vreg_l2a_3p1>;
1281         vdda18-supply = <&vreg_l12a_1p8>;
1282 };
1283
1284 &usb_1_qmpphy {
1285         status = "okay";
1286
1287         vdda-phy-supply = <&vreg_l9a_1p2>;
1288         vdda-pll-supply = <&vreg_l18a_0p92>;
1289 };
1290
1291 &usb_2 {
1292         status = "okay";
1293 };
1294
1295 &usb_2_dwc3 {
1296         dr_mode = "host";
1297 };
1298
1299 &usb_2_hsphy {
1300         status = "okay";
1301
1302         vdda-pll-supply = <&vreg_l5a_0p88>;
1303         vdda33-supply = <&vreg_l2a_3p1>;
1304         vdda18-supply = <&vreg_l12a_1p8>;
1305 };
1306
1307 &usb_2_qmpphy {
1308         status = "okay";
1309
1310         vdda-phy-supply = <&vreg_l9a_1p2>;
1311         vdda-pll-supply = <&vreg_l18a_0p92>;
1312 };
1313
1314 &vamacro {
1315         pinctrl-0 = <&dmic01_active>;
1316         pinctrl-names = "default";
1317         vdd-micb-supply = <&vreg_s4a_1p8>;
1318         qcom,dmic-sample-rate = <600000>;
1319 };
1320
1321 &venus {
1322         status = "okay";
1323 };
1324
1325 /* PINCTRL - additions to nodes defined in sm8250.dtsi */
1326 &qup_spi0_cs_gpio {
1327         drive-strength = <6>;
1328         bias-disable;
1329 };
1330
1331 &qup_spi0_data_clk {
1332         drive-strength = <6>;
1333         bias-disable;
1334 };