arch/arm64/boot/dts/qcom/pm6350.dtsi

   1 // SPDX-License-Identifier: BSD-3-Clause
   2 /*
   3  * Copyright (c) 2021, Luca Weiss <luca@z3ntu.xyz>
   4  */
   5
   6 #include <dt-bindings/input/input.h>
   7 #include <dt-bindings/spmi/spmi.h>
   8
   9 / {
  10         thermal-zones {
  11                 pm6350-thermal {
  12                         polling-delay-passive = <100>;
  13                         polling-delay = <0>;
  14
  15                         thermal-sensors = <&pm6350_temp>;
  16
  17                         trips {
  18                                 trip0 {
  19                                         temperature = <95000>;
  20                                         hysteresis = <0>;
  21                                         type = "passive";
  22                                 };
  23
  24                                 trip1 {
  25                                         temperature = <115000>;
  26                                         hysteresis = <0>;
  27                                         type = "hot";
  28                                 };
  29
  30                                 trip2 {
  31                                         temperature = <125000>;
  32                                         hysteresis = <0>;
  33                                         type = "critical";
  34                                 };
  35                         };
  36                 };
  37         };
  38 };
  39
  40 &spmi_bus {
  41         pmic@0 {
  42                 compatible = "qcom,pm6350", "qcom,spmi-pmic";
  43                 reg = <0x0 SPMI_USID>;
  44                 #address-cells = <1>;
  45                 #size-cells = <0>;
  46
  47                 pm6350_pon: pon@800 {
  48                         compatible = "qcom,pm8998-pon";
  49                         reg = <0x800>;
  50                         mode-bootloader = <0x2>;
  51                         mode-recovery = <0x1>;
  52
  53                         pm6350_pwrkey: pwrkey {
  54                                 compatible = "qcom,pm8941-pwrkey";
  55                                 interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>;
  56                                 debounce = <15625>;
  57                                 bias-pull-up;
  58                                 linux,code = <KEY_POWER>;
  59                         };
  60
  61                         pm6350_resin: resin {
  62                                 compatible = "qcom,pm8941-resin";
  63                                 interrupts = <0x0 0x8 0x1 IRQ_TYPE_EDGE_BOTH>;
  64                                 debounce = <15625>;
  65                                 bias-pull-up;
  66                                 status = "disabled";
  67                         };
  68                 };
  69
  70                 pm6350_temp: temp-alarm@2400 {
  71                         compatible = "qcom,spmi-temp-alarm";
  72                         reg = <0x2400>;
  73                         interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>;
  74                         #thermal-sensor-cells = <0>;
  75                 };
  76
  77                 pm6350_gpios: gpio@c000 {
  78                         compatible = "qcom,pm6350-gpio", "qcom,spmi-gpio";
  79                         reg = <0xc000>;
  80                         gpio-controller;
  81                         gpio-ranges = <&pm6350_gpios 0 0 9>;
  82                         #gpio-cells = <2>;
  83                         interrupt-controller;
  84                         #interrupt-cells = <2>;
  85                 };
  86         };
  87
  88         pmic@1 {
  89                 compatible = "qcom,pm6350", "qcom,spmi-pmic";
  90                 reg = <0x1 SPMI_USID>;
  91                 #address-cells = <1>;
  92                 #size-cells = <0>;
  93         };
  94 };