arch/arm64/boot/dts/qcom/msm8998-sony-xperia-yoshino.dtsi

   1 // SPDX-License-Identifier: BSD-3-Clause
   2 /*
   3  * Copyright (c) 2021, AngeloGioacchino Del Regno
   4  *                     <angelogioacchino.delregno@somainline.org>
   5  * Copyright (c) 2021, Konrad Dybcio <konrad.dybcio@somainline.org>
   6  */
   7
   8 #include <dt-bindings/input/input.h>
   9 #include <dt-bindings/leds/common.h>
  10 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
  11 #include "msm8998.dtsi"
  12 #include "pm8005.dtsi"
  13 #include "pm8998.dtsi"
  14 #include "pmi8998.dtsi"
  15
  16 / {
  17         /* required for bootloader to select correct board */
  18         qcom,msm-id = <0x124 0x20000>, <0x124 0x20001>; /* 8998v2, v2.1 */
  19         qcom,board-id = <8 0>;
  20
  21         clocks {
  22                 div1_mclk: divclk1 {
  23                         compatible = "gpio-gate-clock";
  24                         pinctrl-0 = <&audio_mclk_pin>;
  25                         pinctrl-names = "default";
  26                         clocks = <&rpmcc RPM_SMD_DIV_CLK1>;
  27                         #clock-cells = <0>;
  28                         enable-gpios = <&pm8998_gpio 13 GPIO_ACTIVE_HIGH>;
  29                 };
  30         };
  31
  32         board_vbat: vbat-regulator {
  33                 compatible = "regulator-fixed";
  34                 regulator-name = "VBAT";
  35
  36                 regulator-min-microvolt = <4000000>;
  37                 regulator-max-microvolt = <4000000>;
  38                 regulator-always-on;
  39                 regulator-boot-on;
  40         };
  41
  42         cam0_vdig_vreg: cam0-vdig {
  43                 compatible = "regulator-fixed";
  44                 regulator-name = "cam0_vdig";
  45                 startup-delay-us = <0>;
  46                 enable-active-high;
  47                 gpio = <&tlmm 21 GPIO_ACTIVE_HIGH>;
  48                 pinctrl-names = "default";
  49                 pinctrl-0 = <&cam0_vdig_default>;
  50         };
  51
  52         cam1_vdig_vreg: cam1-vdig {
  53                 compatible = "regulator-fixed";
  54                 regulator-name = "cam1_vdig";
  55                 startup-delay-us = <0>;
  56                 enable-active-high;
  57                 gpio = <&tlmm 25 GPIO_ACTIVE_HIGH>;
  58                 pinctrl-names = "default";
  59                 pinctrl-0 = <&cam1_vdig_default>;
  60                 vin-supply = <&vreg_s3a_1p35>;
  61         };
  62
  63         cam_vio_vreg: cam-vio-vreg {
  64                 compatible = "regulator-fixed";
  65                 regulator-name = "cam_vio_vreg";
  66                 startup-delay-us = <0>;
  67                 enable-active-high;
  68                 gpio = <&pmi8998_gpio 1 GPIO_ACTIVE_HIGH>;
  69                 pinctrl-names = "default";
  70                 pinctrl-0 = <&cam_vio_default>;
  71                 vin-supply = <&vreg_lvs1a_1p8>;
  72         };
  73
  74         touch_vddio_vreg: touch-vddio-vreg {
  75                 compatible = "regulator-fixed";
  76                 regulator-name = "touch_vddio_vreg";
  77                 startup-delay-us = <10000>;
  78                 gpio = <&tlmm 133 GPIO_ACTIVE_HIGH>;
  79                 pinctrl-names = "default";
  80                 pinctrl-0 = <&ts_vddio_en>;
  81         };
  82
  83         vph_pwr: vph-pwr-regulator {
  84                 compatible = "regulator-fixed";
  85                 regulator-name = "vph_pwr";
  86                 regulator-always-on;
  87                 regulator-boot-on;
  88         };
  89
  90         extcon_usb: extcon-usb {
  91                 compatible = "linux,extcon-usb-gpio";
  92                 id-gpio = <&tlmm 38 GPIO_ACTIVE_HIGH>;
  93                 vbus-gpio = <&tlmm 128 GPIO_ACTIVE_HIGH>;
  94                 pinctrl-names = "default";
  95                 pinctrl-0 = <&usb_extcon_active &usb_vbus_active>;
  96         };
  97
  98         gpio-keys {
  99                 compatible = "gpio-keys";
 100                 label = "Side buttons";
 101                 pinctrl-names = "default";
 102                 pinctrl-0 = <&vol_down_pin_a>, <&cam_focus_pin_a>,
 103                             <&cam_snapshot_pin_a>;
 104                 button-vol-down {
 105                         label = "Volume Down";
 106                         gpios = <&pm8998_gpio 5 GPIO_ACTIVE_LOW>;
 107                         linux,input-type = <EV_KEY>;
 108                         linux,code = <KEY_VOLUMEDOWN>;
 109                         gpio-key,wakeup;
 110                         debounce-interval = <15>;
 111                 };
 112
 113                 button-camera-snapshot {
 114                         label = "Camera Snapshot";
 115                         gpios = <&pm8998_gpio 7 GPIO_ACTIVE_LOW>;
 116                         linux,input-type = <EV_KEY>;
 117                         linux,code = <KEY_CAMERA>;
 118                         debounce-interval = <15>;
 119                 };
 120
 121                 button-camera-focus {
 122                         label = "Camera Focus";
 123                         gpios = <&pm8998_gpio 8 GPIO_ACTIVE_LOW>;
 124                         linux,input-type = <EV_KEY>;
 125                         linux,code = <KEY_CAMERA_FOCUS>;
 126                         debounce-interval = <15>;
 127                 };
 128         };
 129
 130         gpio-hall-sensor {
 131                 compatible = "gpio-keys";
 132                 label = "Hall sensors";
 133                 pinctrl-names = "default";
 134                 pinctrl-0 = <&hall_sensor0_default>;
 135
 136                 event-hall-sensor0 {
 137                         label = "Cover Hall Sensor";
 138                         gpios = <&tlmm 124 GPIO_ACTIVE_LOW>;
 139                         linux,input-type = <EV_SW>;
 140                         linux,code = <SW_LID>;
 141                         gpio-key,wakeup;
 142                         debounce-interval = <30>;
 143                 };
 144         };
 145
 146         reserved-memory {
 147                 #address-cells = <2>;
 148                 #size-cells = <2>;
 149                 ranges;
 150
 151                 hyp_mem: memory@85800000 {
 152                         reg = <0x0 0x85800000 0x0 0x3700000>;
 153                         no-map;
 154                 };
 155
 156                 cont_splash_mem: memory@9d400000 {
 157                         reg = <0x0 0x9d400000 0x0 0x2400000>;
 158                         no-map;
 159                 };
 160
 161                 zap_shader_region: memory@f6400000 {
 162                         compatible = "shared-dma-pool";
 163                         reg = <0x0 0xf6400000 0x0 0x2000>;
 164                         no-map;
 165                 };
 166
 167                 adsp_region: memory@fe000000 {
 168                         reg = <0x0 0xfe000000 0x0 0x800000>;
 169                         no-map;
 170                 };
 171
 172                 qseecom_region: memory@fe800000 {
 173                         reg = <0x0 0xfe800000 0x0 0x1400000>;
 174                         no-map;
 175                 };
 176
 177                 ramoops@ffc00000 {
 178                         compatible = "ramoops";
 179                         reg = <0x0 0xffc00000 0x0 0x100000>;
 180                         record-size = <0x10000>;
 181                         console-size = <0x60000>;
 182                         ftrace-size = <0x10000>;
 183                         pmsg-size = <0x20000>;
 184                         ecc-size = <16>;
 185                 };
 186         };
 187
 188         vibrator {
 189                 compatible = "gpio-vibrator";
 190                 enable-gpios = <&pmi8998_gpio 5 GPIO_ACTIVE_HIGH>;
 191                 pinctrl-names = "default";
 192                 pinctrl-0 = <&vib_default>;
 193         };
 194 };
 195
 196 &blsp1_i2c5 {
 197         status = "okay";
 198         clock-frequency = <355000>;
 199
 200         touchscreen@2c {
 201                 compatible = "syna,rmi4-i2c";
 202                 reg = <0x2c>;
 203                 #address-cells = <1>;
 204                 #size-cells = <0>;
 205                 interrupts-extended = <&tlmm 125 IRQ_TYPE_EDGE_FALLING>;
 206
 207                 pinctrl-names = "default";
 208                 pinctrl-0 = <&ts_int_n>;
 209
 210                 vdd-supply = <&vreg_l28_3p0>;
 211                 vio-supply = <&touch_vddio_vreg>;
 212
 213                 syna,reset-delay-ms = <220>;
 214                 syna,startup-delay-ms = <1000>;
 215
 216                 rmi4-f01@1 {
 217                         reg = <0x01>;
 218                         syna,nosleep-mode = <1>;
 219                 };
 220
 221                 rmi4-f11@11 {
 222                         reg = <0x11>;
 223                         syna,sensor-type = <1>;
 224                 };
 225         };
 226 };
 227
 228 &blsp1_i2c5_sleep {
 229         bias-disable;
 230 };
 231
 232 &blsp1_uart3 {
 233         status = "okay";
 234
 235         bluetooth {
 236                 compatible = "qcom,wcn3990-bt";
 237
 238                 vddio-supply = <&vreg_s4a_1p8>;
 239                 vddxo-supply = <&vreg_l7a_1p8>;
 240                 vddrf-supply = <&vreg_l17a_1p3>;
 241                 vddch0-supply = <&vreg_l25a_3p3>;
 242                 max-speed = <3200000>;
 243
 244                 clocks = <&rpmcc RPM_SMD_RF_CLK2_PIN>;
 245         };
 246 };
 247
 248 &blsp2_uart1 {
 249         status = "okay";
 250 };
 251
 252 &blsp2_i2c2 {
 253         status = "okay";
 254
 255         proximity@29 {
 256                 compatible = "st,vl53l0x";
 257                 reg = <0x29>;
 258
 259                 interrupt-parent = <&tlmm>;
 260                 interrupts = <22 IRQ_TYPE_EDGE_FALLING>;
 261
 262                 reset-gpios = <&tlmm 27 GPIO_ACTIVE_LOW>;
 263                 vdd-supply = <&cam_vio_vreg>;
 264
 265                 pinctrl-names = "default";
 266                 pinctrl-0 = <&tof_int &tof_reset>;
 267         };
 268 };
 269
 270 &ibb {
 271         regulator-min-microamp = <800000>;
 272         regulator-max-microamp = <800000>;
 273         regulator-enable-ramp-delay = <200>;
 274         regulator-over-current-protection;
 275         regulator-pull-down;
 276         regulator-ramp-delay = <1>;
 277         regulator-settling-time-up-us = <600>;
 278         regulator-settling-time-down-us = <1000>;
 279         regulator-soft-start;
 280         qcom,discharge-resistor-kohms = <300>;
 281 };
 282
 283 &lab {
 284         regulator-min-microamp = <200000>;
 285         regulator-max-microamp = <200000>;
 286         regulator-enable-ramp-delay = <500>;
 287         regulator-over-current-protection;
 288         regulator-pull-down;
 289         regulator-ramp-delay = <1>;
 290         regulator-settling-time-up-us = <50000>;
 291         regulator-settling-time-down-us = <3000>;
 292         regulator-soft-start;
 293 };
 294
 295 &pm8005_regulators {
 296         /* VDD_GFX supply */
 297         pm8005_s1: s1 {
 298                 regulator-min-microvolt = <524000>;
 299                 regulator-max-microvolt = <1088000>;
 300                 regulator-enable-ramp-delay = <500>;
 301                 /* Hack until we rig up the gpu consumer */
 302                 regulator-always-on;
 303         };
 304 };
 305
 306 &pm8998_gpio {
 307         vol_down_pin_a: vol-down-active-state {
 308                 pins = "gpio5";
 309                 function = PMIC_GPIO_FUNC_NORMAL;
 310                 bias-pull-up;
 311                 input-enable;
 312                 qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
 313         };
 314
 315         cam_focus_pin_a: cam-focus-btn-active-state {
 316                 pins = "gpio7";
 317                 function = PMIC_GPIO_FUNC_NORMAL;
 318                 bias-pull-up;
 319                 input-enable;
 320                 qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
 321         };
 322
 323         cam_snapshot_pin_a: cam-snapshot-btn-active-state {
 324                 pins = "gpio8";
 325                 function = PMIC_GPIO_FUNC_NORMAL;
 326                 bias-pull-up;
 327                 input-enable;
 328                 qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
 329         };
 330
 331         audio_mclk_pin: audio-mclk-pin-active-state {
 332                 pins = "gpio13";
 333                 function = "func2";
 334                 power-source = <0>;
 335         };
 336 };
 337
 338 &pmi8998_gpio {
 339         cam_vio_default: cam-vio-active-state {
 340                 pins = "gpio1";
 341                 function = PMIC_GPIO_FUNC_NORMAL;
 342                 bias-disable;
 343                 drive-push-pull;
 344                 output-low;
 345                 qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>;
 346                 power-source = <1>;
 347         };
 348
 349         vib_default: vib-en-state {
 350                 pins = "gpio5";
 351                 function = PMIC_GPIO_FUNC_NORMAL;
 352                 bias-disable;
 353                 drive-push-pull;
 354                 output-low;
 355                 qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>;
 356                 power-source = <0>;
 357         };
 358 };
 359
 360 &pm8998_pon {
 361         resin {
 362                 compatible = "qcom,pm8941-resin";
 363                 interrupts = <GIC_SPI 0x8 1 IRQ_TYPE_EDGE_BOTH>;
 364                 debounce = <15625>;
 365                 bias-pull-up;
 366                 linux,code = <KEY_VOLUMEUP>;
 367         };
 368 };
 369
 370 &qusb2phy {
 371         status = "okay";
 372
 373         vdda-pll-supply = <&vreg_l12a_1p8>;
 374         vdda-phy-dpdm-supply = <&vreg_l24a_3p075>;
 375 };
 376
 377 &rpm_requests {
 378         pm8998-regulators {
 379                 compatible = "qcom,rpm-pm8998-regulators";
 380
 381                 vdd_s1-supply = <&vph_pwr>;
 382                 vdd_s2-supply = <&vph_pwr>;
 383                 vdd_s3-supply = <&vph_pwr>;
 384                 vdd_s4-supply = <&vph_pwr>;
 385                 vdd_s5-supply = <&vph_pwr>;
 386                 vdd_s6-supply = <&vph_pwr>;
 387                 vdd_s7-supply = <&vph_pwr>;
 388                 vdd_s8-supply = <&vph_pwr>;
 389                 vdd_s9-supply = <&vph_pwr>;
 390                 vdd_s10-supply = <&vph_pwr>;
 391                 vdd_s11-supply = <&vph_pwr>;
 392                 vdd_s12-supply = <&vph_pwr>;
 393                 vdd_s13-supply = <&vph_pwr>;
 394                 vdd_l1_l27-supply = <&vreg_s7a_1p025>;
 395                 vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>;
 396                 vdd_l3_l11-supply = <&vreg_s7a_1p025>;
 397                 vdd_l4_l5-supply = <&vreg_s7a_1p025>;
 398                 vdd_l6-supply = <&vreg_s5a_2p04>;
 399                 vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>;
 400                 vdd_l9-supply = <&vreg_bob>;
 401                 vdd_l10_l23_l25-supply = <&vreg_bob>;
 402                 vdd_l13_l19_l21-supply = <&vreg_bob>;
 403                 vdd_l16_l28-supply = <&vreg_bob>;
 404                 vdd_l18_l22-supply = <&vreg_bob>;
 405                 vdd_l20_l24-supply = <&vreg_bob>;
 406                 vdd_l26-supply = <&vreg_s3a_1p35>;
 407                 vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>;
 408
 409                 vreg_s3a_1p35: s3 {
 410                         regulator-min-microvolt = <1352000>;
 411                         regulator-max-microvolt = <1352000>;
 412                 };
 413                 vreg_s4a_1p8: s4 {
 414                         regulator-min-microvolt = <1800000>;
 415                         regulator-max-microvolt = <1800000>;
 416                         regulator-system-load = <100000>;
 417                         regulator-allow-set-load;
 418                 };
 419                 vreg_s5a_2p04: s5 {
 420                         regulator-min-microvolt = <1904000>;
 421                         regulator-max-microvolt = <2032000>;
 422                 };
 423                 vreg_s7a_1p025: s7 {
 424                         regulator-min-microvolt = <900000>;
 425                         regulator-max-microvolt = <1028000>;
 426                 };
 427                 vreg_l1a_0p875: l1 {
 428                         regulator-min-microvolt = <880000>;
 429                         regulator-max-microvolt = <880000>;
 430                         regulator-system-load = <73400>;
 431                         regulator-allow-set-load;
 432                 };
 433                 vreg_l2a_1p2: l2 {
 434                         regulator-min-microvolt = <1200000>;
 435                         regulator-max-microvolt = <1200000>;
 436                         regulator-system-load = <12560>;
 437                         regulator-allow-set-load;
 438                 };
 439                 vreg_l3a_1p0: l3 {
 440                         regulator-min-microvolt = <1000000>;
 441                         regulator-max-microvolt = <1000000>;
 442                 };
 443                 vreg_l5a_0p8: l5 {
 444                         regulator-min-microvolt = <800000>;
 445                         regulator-max-microvolt = <800000>;
 446                 };
 447                 vreg_l6a_1p8: l6 {
 448                         regulator-min-microvolt = <1800000>;
 449                         regulator-max-microvolt = <1800000>;
 450                 };
 451                 vreg_l7a_1p8: l7 {
 452                         regulator-min-microvolt = <1800000>;
 453                         regulator-max-microvolt = <1800000>;
 454                 };
 455                 vreg_l8a_1p2: l8 {
 456                         regulator-min-microvolt = <1200000>;
 457                         regulator-max-microvolt = <1200000>;
 458                 };
 459                 vreg_l9a_1p8: l9 {
 460                         regulator-min-microvolt = <1808000>;
 461                         regulator-max-microvolt = <2960000>;
 462                 };
 463                 vreg_l10a_1p8: l10 {
 464                         regulator-min-microvolt = <1808000>;
 465                         regulator-max-microvolt = <2960000>;
 466                 };
 467                 vreg_l11a_1p0: l11 {
 468                         regulator-min-microvolt = <1000000>;
 469                         regulator-max-microvolt = <1000000>;
 470                 };
 471                 vreg_l12a_1p8: l12 {
 472                         regulator-min-microvolt = <1800000>;
 473                         regulator-max-microvolt = <1800000>;
 474                 };
 475                 vreg_l13a_2p95: l13 {
 476                         regulator-min-microvolt = <1808000>;
 477                         regulator-max-microvolt = <2960000>;
 478                         regulator-allow-set-load;
 479                 };
 480                 vreg_l14a_1p85: l14 {
 481                         regulator-min-microvolt = <1848000>;
 482                         regulator-max-microvolt = <1856000>;
 483                         regulator-system-load = <32000>;
 484                         regulator-allow-set-load;
 485                 };
 486                 vreg_l15a_1p8: l15 {
 487                         regulator-min-microvolt = <1800000>;
 488                         regulator-max-microvolt = <1800000>;
 489                 };
 490                 vreg_l16a_2p7: l16 {
 491                         regulator-min-microvolt = <2704000>;
 492                         regulator-max-microvolt = <2704000>;
 493                 };
 494                 vreg_l17a_1p3: l17 {
 495                         regulator-min-microvolt = <1304000>;
 496                         regulator-max-microvolt = <1304000>;
 497                 };
 498                 vreg_l18a_2p85: l18 {};
 499                 vreg_l19a_2p7: l19 {
 500                         regulator-min-microvolt = <2696000>;
 501                         regulator-max-microvolt = <2704000>;
 502                 };
 503                 vreg_l20a_2p95: l20 {
 504                         regulator-min-microvolt = <2960000>;
 505                         regulator-max-microvolt = <2960000>;
 506                         regulator-system-load = <10000>;
 507                         regulator-allow-set-load;
 508                 };
 509                 vreg_l21a_2p95: l21 {
 510                         regulator-min-microvolt = <2960000>;
 511                         regulator-max-microvolt = <2960000>;
 512                         regulator-system-load = <800000>;
 513                         regulator-allow-set-load;
 514                 };
 515                 vreg_l22a_2p85: l22 { };
 516                 vreg_l23a_3p3: l23 {
 517                         regulator-min-microvolt = <3312000>;
 518                         regulator-max-microvolt = <3312000>;
 519                 };
 520                 vreg_l24a_3p075: l24 {
 521                         regulator-min-microvolt = <3088000>;
 522                         regulator-max-microvolt = <3088000>;
 523                 };
 524                 vreg_l25a_3p3: l25 {
 525                         regulator-min-microvolt = <3104000>;
 526                         regulator-max-microvolt = <3312000>;
 527                 };
 528                 vreg_l26a_1p2: l26 {
 529                         regulator-min-microvolt = <1200000>;
 530                         regulator-max-microvolt = <1200000>;
 531                         regulator-allow-set-load;
 532                 };
 533                 vreg_l28_3p0: l28 {
 534                         regulator-min-microvolt = <3000000>;
 535                         regulator-max-microvolt = <3000000>;
 536                 };
 537                 vreg_lvs1a_1p8: lvs1 { };
 538                 vreg_lvs2a_1p8: lvs2 { };
 539         };
 540
 541         pmi8998-regulators {
 542                 compatible = "qcom,rpm-pmi8998-regulators";
 543
 544                 vdd_bob-supply = <&vph_pwr>;
 545
 546                 vreg_bob: bob {
 547                         regulator-min-microvolt = <3312000>;
 548                         regulator-max-microvolt = <3600000>;
 549                 };
 550         };
 551 };
 552
 553 &sdhc2 {
 554         status = "okay";
 555         cd-gpios = <&tlmm 95 GPIO_ACTIVE_HIGH>;
 556
 557         vmmc-supply = <&vreg_l21a_2p95>;
 558         vqmmc-supply = <&vreg_l13a_2p95>;
 559
 560         pinctrl-names = "default", "sleep";
 561         pinctrl-0 = <&sdc2_on &sdc2_cd>;
 562         pinctrl-1 = <&sdc2_off &sdc2_cd>;
 563 };
 564
 565 &tlmm {
 566         gpio-reserved-ranges = <0 4>, <81 4>;
 567
 568         mdp_vsync_n: mdp-vsync-n {
 569                 pins = "gpio10";
 570                 function = "mdp_vsync_a";
 571                 drive-strength = <2>;
 572                 bias-pull-down;
 573         };
 574
 575         nfc_ven: nfc-ven {
 576                 pins = "gpio12";
 577                 function = "gpio";
 578                 bias-disable;
 579                 drive-strength = <2>;
 580                 output-low;
 581         };
 582
 583         msm_mclk0_default: msm-mclk0-active {
 584                 pins = "gpio13";
 585                 function = "cam_mclk";
 586                 drive-strength = <2>;
 587                 bias-disable;
 588         };
 589
 590         msm_mclk1_default: msm-mclk1-active {
 591                 pins = "gpio14";
 592                 function = "cam_mclk";
 593                 drive-strength = <2>;
 594                 bias-disable;
 595         };
 596
 597         cci0_default: cci0-default {
 598                 pins = "gpio18", "gpio19";
 599                 function = "cci_i2c";
 600                 bias-disable;
 601                 drive-strength = <2>;
 602         };
 603
 604         cci1_default: cci1-default {
 605                 pins = "gpio19", "gpio20";
 606                 function = "cci_i2c";
 607                 bias-disable;
 608                 drive-strength = <2>;
 609         };
 610
 611         cam0_vdig_default: cam0-vdig-default {
 612                 pins = "gpio21";
 613                 function = "gpio";
 614                 bias-disable;
 615                 drive-strength = <2>;
 616         };
 617
 618         tof_int: tof-int {
 619                 pins = "gpio22";
 620                 function = "gpio";
 621                 bias-pull-up;
 622                 drive-strength = <2>;
 623                 input-enable;
 624         };
 625
 626         cam1_vdig_default: cam1-vdig-default {
 627                 pins = "gpio25";
 628                 function = "gpio";
 629                 bias-disable;
 630                 drive-strength = <2>;
 631         };
 632
 633         usb_extcon_active: usb-extcon-active {
 634                 pins = "gpio38";
 635                 function = "gpio";
 636                 bias-disable;
 637                 drive-strength = <16>;
 638         };
 639
 640         tof_reset: tof-reset {
 641                 pins = "gpio27";
 642                 function = "gpio";
 643                 bias-disable;
 644                 drive-strength = <2>;
 645         };
 646
 647         hall_sensor0_default: acc-cover-open {
 648                 pins = "gpio124";
 649                 function = "gpio";
 650                 bias-disable;
 651                 drive-strength = <2>;
 652                 input-enable;
 653         };
 654
 655         ts_int_n: ts-int-n {
 656                 pins = "gpio125";
 657                 function = "gpio";
 658                 drive-strength = <8>;
 659                 bias-pull-up;
 660         };
 661
 662         usb_vbus_active: usb-vbus-active {
 663                 pins = "gpio128";
 664                 function = "gpio";
 665                 bias-disable;
 666                 drive-strength = <2>;
 667                 output-low;
 668         };
 669
 670         ts_vddio_en: ts-vddio-en-default {
 671                 pins = "gpio133";
 672                 function = "gpio";
 673                 bias-disable;
 674                 drive-strength = <2>;
 675                 output-low;
 676         };
 677 };
 678
 679 /*
 680  * WARNING:
 681  * Disable UFS until card quirks are in to avoid unrecoverable hard-brick
 682  * that would happen as soon as the UFS card gets probed as, without the
 683  * required quirks, the bootloader will be erased right after card probe.
 684  */
 685 &ufshc {
 686         status = "disabled";
 687 };
 688
 689 &ufsphy {
 690         status = "disabled";
 691 };
 692
 693 &usb3 {
 694         status = "okay";
 695 };
 696
 697 &usb3_dwc3 {
 698         /* Force to peripheral until we have Type-C hooked up */
 699         dr_mode = "peripheral";
 700         extcon = <&extcon_usb>;
 701 };
 702
 703 &usb3phy {
 704         status = "okay";
 705
 706         vdda-phy-supply = <&vreg_l1a_0p875>;
 707         vdda-pll-supply = <&vreg_l2a_1p2>;
 708 };