arch/arm64/boot/dts/qcom/msm8953-xiaomi-vince.dts

   1 // SPDX-License-Identifier: BSD-3-Clause
   2 /*
   3  * Copyright (c) 2022, Eugene Lepshy <fekz115@gmail.com>
   4  * Copyright (c) 2022, Gianluca Boiano <morf3089@gmail.com>
   5  */
   6 /dts-v1/;
   7
   8 #include "msm8953.dtsi"
   9 #include "pm8953.dtsi"
  10 #include "pmi8950.dtsi"
  11 #include <dt-bindings/leds/common.h>
  12
  13 /delete-node/ &adsp_fw_mem;
  14 /delete-node/ &cont_splash_mem;
  15 /delete-node/ &qseecom_mem;
  16 /delete-node/ &wcnss_fw_mem;
  17
  18 / {
  19         model = "Xiaomi Redmi 5 Plus";
  20         compatible = "xiaomi,vince", "qcom,msm8953";
  21         chassis-type = "handset";
  22         qcom,msm-id = <293 0>;
  23         qcom,board-id = <0x1000b 0x08>;
  24
  25         gpio-keys {
  26                 compatible = "gpio-keys";
  27
  28                 pinctrl-names = "default";
  29                 pinctrl-0 = <&gpio_key_default>;
  30
  31                 key-volume-up {
  32                         label = "volume_up";
  33                         linux,code = <KEY_VOLUMEUP>;
  34                         gpios = <&tlmm 85 GPIO_ACTIVE_LOW>;
  35                 };
  36         };
  37
  38         reserved-memory {
  39                 qseecom_mem: qseecom@84a00000 {
  40                         reg = <0x0 0x84a00000 0x0 0x1900000>;
  41                         no-map;
  42                 };
  43
  44                 cont_splash_mem: cont-splash@90001000 {
  45                         reg = <0x0 0x90001000 0x0 (1080 * 2160 * 3)>;
  46                         no-map;
  47                 };
  48
  49                 adsp_fw_mem: adsp@8d600000 {
  50                         reg = <0x0 0x8d600000 0x0 0x1200000>;
  51                         no-map;
  52                 };
  53
  54                 wcnss_fw_mem: wcnss@8e800000 {
  55                         reg = <0x0 0x8e800000 0x0 0x700000>;
  56                         no-map;
  57                 };
  58
  59                 ramoops@9ff00000 {
  60                         compatible = "ramoops";
  61                         reg = <0x0 0x9ff00000 0x0 0x100000>;
  62                         record-size = <0x1000>;
  63                         console-size = <0x80000>;
  64                         ftrace-size = <0x1000>;
  65                         pmsg-size = <0x8000>;
  66                 };
  67         };
  68
  69         /*
  70          * We bitbang on &i2c_4 because BLSP is protected by TZ as sensors are
  71          * normally proxied via ADSP firmware. GPIOs aren't protected.
  72          */
  73         i2c-sensors {
  74                 compatible = "i2c-gpio";
  75                 sda-gpios = <&tlmm 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
  76                 scl-gpios = <&tlmm 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
  77                 i2c-gpio,delay-us = <2>; /* ~100 kHz */
  78                 #address-cells = <1>;
  79                 #size-cells = <0>;
  80
  81                 imu@6a {
  82                         compatible = "st,lsm6dsl";
  83                         reg = <0x6a>;
  84                         vdd-supply = <&pm8953_l10>;
  85                         vddio-supply = <&pm8953_l6>;
  86                         mount-matrix = "1", "0", "0",
  87                                         "0", "-1", "0",
  88                                         "0", "0", "1";
  89                 };
  90         };
  91
  92         vph_pwr: vph-pwr-regulator {
  93                 compatible = "regulator-fixed";
  94                 regulator-name = "vph_pwr";
  95                 regulator-always-on;
  96                 regulator-boot-on;
  97         };
  98 };
  99
 100 &hsusb_phy {
 101         vdd-supply = <&pm8953_l3>;
 102         vdda-pll-supply = <&pm8953_l7>;
 103         vdda-phy-dpdm-supply = <&pm8953_l13>;
 104
 105         status = "okay";
 106 };
 107
 108 &i2c_2 {
 109         status = "okay";
 110
 111         led-controller@45 {
 112                 compatible = "awinic,aw2013";
 113                 reg = <0x45>;
 114
 115                 vcc-supply = <&pm8953_l10>;
 116
 117                 #address-cells = <1>;
 118                 #size-cells = <0>;
 119
 120                 led@0 {
 121                         reg = <0>;
 122                         led-max-microamp = <5000>;
 123                         function = LED_FUNCTION_INDICATOR;
 124                         color = <LED_COLOR_ID_WHITE>;
 125                 };
 126         };
 127 };
 128
 129 &i2c_3 {
 130         status = "okay";
 131
 132         touchscreen@20 {
 133                 reg = <0x20>;
 134                 compatible = "syna,rmi4-i2c";
 135                 interrupts-extended = <&tlmm 65 IRQ_TYPE_EDGE_FALLING>;
 136
 137                 #address-cells = <1>;
 138                 #size-cells = <0>;
 139
 140                 vdd-supply = <&pm8953_l10>;
 141                 vio-supply = <&pm8953_l6>;
 142
 143                 pinctrl-names = "init", "suspend";
 144                 pinctrl-0 = <&ts_reset_active &ts_int_active>;
 145                 pinctrl-1 = <&ts_reset_suspend &ts_int_suspend>;
 146                 syna,reset-delay-ms = <200>;
 147                 syna,startup-delay-ms = <500>;
 148
 149                 rmi4-f01@1 {
 150                         reg = <0x01>;
 151                         syna,nosleep-mode = <1>;
 152                 };
 153
 154                 rmi4-f12@12 {
 155                         reg = <0x12>;
 156                         syna,rezero-wait-ms = <20>;
 157                         syna,sensor-type = <1>;
 158                         touchscreen-x-mm = <68>;
 159                         touchscreen-y-mm = <122>;
 160                 };
 161         };
 162 };
 163
 164 &pm8953_resin {
 165         linux,code = <KEY_VOLUMEDOWN>;
 166         status = "okay";
 167 };
 168
 169 &pmi8950_wled {
 170         qcom,current-limit-microamp = <20000>;
 171         qcom,ovp-millivolt = <29600>;
 172         qcom,num-strings = <2>;
 173         qcom,external-pfet;
 174         qcom,cabc;
 175
 176         status = "okay";
 177 };
 178
 179 &rpm_requests {
 180         regulators {
 181                 compatible = "qcom,rpm-pm8953-regulators";
 182                 vdd_s1-supply = <&vph_pwr>;
 183                 vdd_s2-supply = <&vph_pwr>;
 184                 vdd_s3-supply = <&vph_pwr>;
 185                 vdd_s4-supply = <&vph_pwr>;
 186                 vdd_s5-supply = <&vph_pwr>;
 187                 vdd_s6-supply = <&vph_pwr>;
 188                 vdd_s7-supply = <&vph_pwr>;
 189                 vdd_l1-supply = <&pm8953_s3>;
 190                 vdd_l2_l3-supply = <&pm8953_s3>;
 191                 vdd_l4_l5_l6_l7_l16_l19-supply = <&pm8953_s4>;
 192                 vdd_l8_l11_l12_l13_l14_l15-supply = <&vph_pwr>;
 193                 vdd_l9_l10_l17_l18_l22-supply = <&vph_pwr>;
 194
 195                 pm8953_s1: s1 {
 196                         regulator-min-microvolt = <870000>;
 197                         regulator-max-microvolt = <1156000>;
 198                 };
 199
 200                 pm8953_s3: s3 {
 201                         regulator-min-microvolt = <984000>;
 202                         regulator-max-microvolt = <1224000>;
 203                 };
 204
 205                 pm8953_s4: s4 {
 206                         regulator-min-microvolt = <1900000>;
 207                         regulator-max-microvolt = <2050000>;
 208                 };
 209
 210                 pm8953_l1: l1 {
 211                         regulator-min-microvolt = <1000000>;
 212                         regulator-max-microvolt = <1100000>;
 213                 };
 214
 215                 pm8953_l2: l2 {
 216                         regulator-min-microvolt = <1200000>;
 217                         regulator-max-microvolt = <1225000>;
 218                 };
 219
 220                 pm8953_l3: l3 {
 221                         regulator-min-microvolt = <925000>;
 222                         regulator-max-microvolt = <925000>;
 223                 };
 224
 225                 pm8953_l5: l5 {
 226                         regulator-min-microvolt = <1800000>;
 227                         regulator-max-microvolt = <1800000>;
 228                 };
 229
 230                 pm8953_l6: l6 {
 231                         regulator-min-microvolt = <1800000>;
 232                         regulator-max-microvolt = <1800000>;
 233                 };
 234
 235                 pm8953_l7: l7 {
 236                         regulator-min-microvolt = <1800000>;
 237                         regulator-max-microvolt = <1900000>;
 238                 };
 239
 240                 pm8953_l8: l8 {
 241                         regulator-min-microvolt = <2900000>;
 242                         regulator-max-microvolt = <2900000>;
 243                 };
 244
 245                 pm8953_l9: l9 {
 246                         regulator-min-microvolt = <3000000>;
 247                         regulator-max-microvolt = <3300000>;
 248                 };
 249
 250                 pm8953_l10: l10 {
 251                         regulator-min-microvolt = <2850000>;
 252                         regulator-max-microvolt = <2850000>;
 253                 };
 254
 255                 pm8953_l11: l11 {
 256                         regulator-min-microvolt = <2950000>;
 257                         regulator-max-microvolt = <2950000>;
 258                 };
 259
 260                 pm8953_l12: l12 {
 261                         regulator-min-microvolt = <1800000>;
 262                         regulator-max-microvolt = <2950000>;
 263                 };
 264
 265                 pm8953_l13: l13 {
 266                         regulator-min-microvolt = <3125000>;
 267                         regulator-max-microvolt = <3125000>;
 268                 };
 269
 270                 pm8953_l16: l16 {
 271                         regulator-min-microvolt = <1800000>;
 272                         regulator-max-microvolt = <1800000>;
 273                 };
 274
 275                 pm8953_l17: l17 {
 276                         regulator-min-microvolt = <2750000>;
 277                         regulator-max-microvolt = <2850000>;
 278                 };
 279
 280                 pm8953_l19: l19 {
 281                         regulator-min-microvolt = <1200000>;
 282                         regulator-max-microvolt = <1380000>;
 283                 };
 284
 285                 pm8953_l22: l22 {
 286                         regulator-min-microvolt = <2800000>;
 287                         regulator-max-microvolt = <2800000>;
 288                 };
 289
 290                 pm8953_l23: l23 {
 291                         regulator-min-microvolt = <1200000>;
 292                         regulator-max-microvolt = <1225000>;
 293                 };
 294         };
 295 };
 296
 297 &sdhc_1 {
 298         vmmc-supply = <&pm8953_l8>;
 299         vqmmc-supply = <&pm8953_l5>;
 300
 301         status = "okay";
 302 };
 303
 304 &sdhc_2 {
 305         vmmc-supply = <&pm8953_l11>;
 306         vqmmc-supply = <&pm8953_l12>;
 307
 308         pinctrl-names = "default", "sleep";
 309         pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>;
 310         pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>;
 311
 312         status = "okay";
 313 };
 314
 315 &tlmm {
 316         gpio-reserved-ranges = <0 4>, <16 4>, <135 4>;
 317
 318         ts_reset_active: ts-reset-active-state {
 319                 pins = "gpio64";
 320                 function = "gpio";
 321                 drive-strength = <8>;
 322                 bias-pull-up;
 323         };
 324
 325         ts_reset_suspend: ts-reset-suspend-state {
 326                 pins = "gpio64";
 327                 function = "gpio";
 328                 drive-strength = <2>;
 329                 bias-pull-up;
 330         };
 331
 332         ts_int_active: ts-int-active-state {
 333                 pins = "gpio65";
 334                 function = "gpio";
 335                 drive-strength = <8>;
 336                 bias-pull-up;
 337         };
 338
 339         ts_int_suspend: ts-int-suspend-state {
 340                 pins = "gpio65";
 341                 function = "gpio";
 342                 drive-strength = <2>;
 343                 bias-pull-down;
 344         };
 345 };
 346
 347 &uart_0 {
 348         pinctrl-names = "default";
 349         pinctrl-0 = <&uart_console_active>;
 350
 351         status = "okay";
 352 };
 353
 354 &usb3 {
 355         status = "okay";
 356 };
 357
 358 &usb3_dwc3 {
 359         dr_mode = "peripheral";
 360 };