4 * Copyright(c) 2015 Broadcom Corporation. All rights reserved.
6 * Redistribution and use in source and binary forms, with or without
7 * modification, are permitted provided that the following conditions
10 * * Redistributions of source code must retain the above copyright
11 * notice, this list of conditions and the following disclaimer.
12 * * Redistributions in binary form must reproduce the above copyright
13 * notice, this list of conditions and the following disclaimer in
14 * the documentation and/or other materials provided with the
16 * * Neither the name of Broadcom Corporation nor the names of its
17 * contributors may be used to endorse or promote products derived
18 * from this software without specific prior written permission.
20 * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
21 * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
22 * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
23 * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
24 * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
25 * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
26 * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
27 * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
28 * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
29 * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
30 * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
38 model = "Broadcom NS2 SVK";
39 compatible = "brcm,ns2-svk", "brcm,ns2";
49 stdout-path = "serial0:115200n8";
50 bootargs = "earlycon=uart8250,mmio32,0x66130000";
54 device_type = "memory";
55 reg = <0x00000000 0x80000000 0x00000000 0x40000000>;
111 compatible = "silabs,si3226x";
113 spi-max-frequency = <5000000>;
116 pl022,interface = <0>;
117 pl022,slave-tx-disable = <0>;
118 pl022,com-mode = <0>;
119 pl022,rx-level-trig = <1>;
120 pl022,tx-level-trig = <1>;
121 pl022,ctrl-len = <11>;
122 pl022,wait-state = <0>;
131 compatible = "atmel,at25";
133 spi-max-frequency = <5000000>;
134 at25,byte-len = <0x8000>;
135 at25,addr-mode = <2>;
136 at25,page-size = <64>;
139 pl022,interface = <0>;
140 pl022,slave-tx-disable = <0>;
141 pl022,com-mode = <0>;
142 pl022,rx-level-trig = <1>;
143 pl022,tx-level-trig = <1>;
144 pl022,ctrl-len = <11>;
145 pl022,wait-state = <0>;
172 compatible = "brcm,nandcs";
174 nand-ecc-mode = "hw";
175 nand-ecc-strength = <8>;
176 nand-ecc-step-size = <512>;
177 nand-bus-width = <16>;
178 brcm,nand-oob-sector-size = <16>;
179 #address-cells = <1>;
194 pinctrl-names = "default";
195 pinctrl-0 = <&nand_sel>;
205 #address-cells = <1>;
207 compatible = "m25p80";
209 spi-max-frequency = <12500000>;
216 reg = <0x00000000 0x000a0000>;
221 reg = <0x000a0000 0x00060000>;
226 reg = <0x00100000 0x00600000>;
231 reg = <0x00700000 0x01900000>;