1 // SPDX-License-Identifier: GPL-2.0-only
3 * linux/arch/arm/mach-omap1/board-h2.c
5 * Board specific inits for OMAP-1610 H2
7 * Copyright (C) 2001 RidgeRun, Inc.
8 * Author: Greg Lonnon <glonnon@ridgerun.com>
10 * Copyright (C) 2002 MontaVista Software, Inc.
12 * Separated FPGA interrupts from innovator1510.c and cleaned up for 2.6
13 * Copyright (C) 2004 Nokia Corporation by Tony Lindrgen <tony@atomide.com>
15 * H2 specific changes and cleanup
16 * Copyright (C) 2004 Nokia Corporation by Imre Deak <imre.deak@nokia.com>
18 #include <linux/gpio.h>
19 #include <linux/gpio/machine.h>
20 #include <linux/kernel.h>
21 #include <linux/platform_device.h>
22 #include <linux/delay.h>
23 #include <linux/i2c.h>
24 #include <linux/mtd/mtd.h>
25 #include <linux/mtd/platnand.h>
26 #include <linux/mtd/physmap.h>
27 #include <linux/input.h>
28 #include <linux/mfd/tps65010.h>
29 #include <linux/smc91x.h>
30 #include <linux/omapfb.h>
31 #include <linux/omap-dma.h>
32 #include <linux/platform_data/gpio-omap.h>
33 #include <linux/platform_data/keypad-omap.h>
34 #include <linux/leds.h>
36 #include <asm/mach-types.h>
37 #include <asm/mach/arch.h>
38 #include <asm/mach/map.h>
48 /* The first 16 SoC GPIO lines are on this GPIO chip */
49 #define OMAP_GPIO_LABEL "gpio-0-15"
51 /* At OMAP1610 Innovator the Ethernet is directly connected to CS1 */
52 #define OMAP1610_ETHR_START 0x04000300
54 static const unsigned int h2_keymap[] = {
92 static struct mtd_partition h2_nor_partitions[] = {
93 /* bootloader (U-Boot, etc) in first sector */
98 .mask_flags = MTD_WRITEABLE, /* force read-only */
100 /* bootloader params in the next sector */
103 .offset = MTDPART_OFS_APPEND,
110 .offset = MTDPART_OFS_APPEND,
116 .name = "filesystem",
117 .offset = MTDPART_OFS_APPEND,
118 .size = MTDPART_SIZ_FULL,
123 static struct physmap_flash_data h2_nor_data = {
125 .set_vpp = omap1_set_vpp,
126 .parts = h2_nor_partitions,
127 .nr_parts = ARRAY_SIZE(h2_nor_partitions),
130 static struct resource h2_nor_resource = {
131 /* This is on CS3, wherever it's mapped */
132 .flags = IORESOURCE_MEM,
135 static struct platform_device h2_nor_device = {
136 .name = "physmap-flash",
139 .platform_data = &h2_nor_data,
142 .resource = &h2_nor_resource,
145 static struct mtd_partition h2_nand_partitions[] = {
147 /* REVISIT: enable these partitions if you make NAND BOOT
148 * work on your H2 (rev C or newer); published versions of
149 * x-load only support P2 and H3.
155 .mask_flags = MTD_WRITEABLE, /* force read-only */
158 .name = "bootloader",
159 .offset = MTDPART_OFS_APPEND,
161 .mask_flags = MTD_WRITEABLE, /* force read-only */
165 .offset = MTDPART_OFS_APPEND,
170 .offset = MTDPART_OFS_APPEND,
175 .name = "filesystem",
176 .size = MTDPART_SIZ_FULL,
177 .offset = MTDPART_OFS_APPEND,
181 #define H2_NAND_RB_GPIO_PIN 62
183 static int h2_nand_dev_ready(struct nand_chip *chip)
185 return gpio_get_value(H2_NAND_RB_GPIO_PIN);
188 static struct platform_nand_data h2_nand_platdata = {
192 .nr_partitions = ARRAY_SIZE(h2_nand_partitions),
193 .partitions = h2_nand_partitions,
194 .options = NAND_SAMSUNG_LP_OPTIONS,
197 .cmd_ctrl = omap1_nand_cmd_ctl,
198 .dev_ready = h2_nand_dev_ready,
202 static struct resource h2_nand_resource = {
203 .flags = IORESOURCE_MEM,
206 static struct platform_device h2_nand_device = {
210 .platform_data = &h2_nand_platdata,
213 .resource = &h2_nand_resource,
216 static struct smc91x_platdata h2_smc91x_info = {
217 .flags = SMC91X_USE_16BIT | SMC91X_NOWAIT,
218 .leda = RPC_LED_100_10,
219 .ledb = RPC_LED_TX_RX,
222 static struct resource h2_smc91x_resources[] = {
224 .start = OMAP1610_ETHR_START, /* Physical */
225 .end = OMAP1610_ETHR_START + 0xf,
226 .flags = IORESOURCE_MEM,
229 .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWEDGE,
233 static struct platform_device h2_smc91x_device = {
237 .platform_data = &h2_smc91x_info,
239 .num_resources = ARRAY_SIZE(h2_smc91x_resources),
240 .resource = h2_smc91x_resources,
243 static struct resource h2_kp_resources[] = {
245 .start = INT_KEYBOARD,
247 .flags = IORESOURCE_IRQ,
251 static const struct matrix_keymap_data h2_keymap_data = {
253 .keymap_size = ARRAY_SIZE(h2_keymap),
256 static struct omap_kp_platform_data h2_kp_data = {
259 .keymap_data = &h2_keymap_data,
265 static struct platform_device h2_kp_device = {
266 .name = "omap-keypad",
269 .platform_data = &h2_kp_data,
271 .num_resources = ARRAY_SIZE(h2_kp_resources),
272 .resource = h2_kp_resources,
275 static const struct gpio_led h2_gpio_led_pins[] = {
278 .default_trigger = "heartbeat",
283 .default_trigger = "cpu0",
284 .gpio = OMAP_MPUIO(4),
288 static struct gpio_led_platform_data h2_gpio_led_data = {
289 .leds = h2_gpio_led_pins,
290 .num_leds = ARRAY_SIZE(h2_gpio_led_pins),
293 static struct platform_device h2_gpio_leds = {
297 .platform_data = &h2_gpio_led_data,
301 static struct platform_device *h2_devices[] __initdata = {
309 static void __init h2_init_smc91x(void)
311 if (gpio_request(0, "SMC91x irq") < 0) {
312 printk("Error requesting gpio 0 for smc91x irq\n");
317 static int tps_setup(struct i2c_client *client, void *context)
319 if (!IS_BUILTIN(CONFIG_TPS65010))
322 tps65010_config_vregs1(TPS_LDO2_ENABLE | TPS_VLDO2_3_0V |
323 TPS_LDO1_ENABLE | TPS_VLDO1_3_0V);
328 static struct tps65010_board tps_board = {
329 .base = H2_TPS_GPIO_BASE,
334 static struct i2c_board_info __initdata h2_i2c_board_info[] = {
336 I2C_BOARD_INFO("tps65010", 0x48),
337 .platform_data = &tps_board,
339 .type = "isp1301_omap",
341 .dev_name = "isp1301",
345 static struct gpiod_lookup_table isp1301_gpiod_table = {
348 /* Active low since the irq triggers on falling edge */
349 GPIO_LOOKUP(OMAP_GPIO_LABEL, 2,
350 NULL, GPIO_ACTIVE_LOW),
355 static struct omap_usb_config h2_usb_config __initdata = {
356 /* usb1 has a Mini-AB port and external isp1301 transceiver */
359 #if IS_ENABLED(CONFIG_USB_OMAP)
360 .hmc_mode = 19, /* 0:host(off) 1:dev|otg 2:disabled */
361 /* .hmc_mode = 21,*/ /* 0:host(off) 1:dev(loopback) 2:host(loopback) */
362 #elif IS_ENABLED(CONFIG_USB_OHCI_HCD)
363 /* needs OTG cable, or NONSTANDARD (B-to-MiniB) */
364 .hmc_mode = 20, /* 1:dev|otg(off) 1:host 2:disabled */
370 static const struct omap_lcd_config h2_lcd_config __initconst = {
371 .ctrl_name = "internal",
374 static void __init h2_init(void)
378 /* Here we assume the NOR boot config: NOR on CS3 (possibly swapped
379 * to address 0 by a dip switch), NAND on CS2B. The NAND driver will
380 * notice whether a NAND chip is enabled at probe time.
382 * FIXME revC boards (and H3) support NAND-boot, with a dip switch to
383 * put NOR on CS2B and NAND (which on H2 may be 16bit) on CS3. Try
384 * detecting that in code here, to avoid probing every possible flash
387 h2_nor_resource.end = h2_nor_resource.start = omap_cs3_phys();
388 h2_nor_resource.end += SZ_32M - 1;
390 h2_nand_resource.end = h2_nand_resource.start = OMAP_CS2B_PHYS;
391 h2_nand_resource.end += SZ_4K - 1;
392 BUG_ON(gpio_request(H2_NAND_RB_GPIO_PIN, "NAND ready") < 0);
393 gpio_direction_input(H2_NAND_RB_GPIO_PIN);
395 gpiod_add_lookup_table(&isp1301_gpiod_table);
397 omap_cfg_reg(L3_1610_FLASH_CS2B_OE);
398 omap_cfg_reg(M8_1610_FLASH_CS2B_WE);
400 /* MMC: card detect and WP */
401 /* omap_cfg_reg(U19_ARMIO1); */ /* CD */
402 omap_cfg_reg(BALLOUT_V8_ARMIO3); /* WP */
404 /* Mux pins for keypad */
405 omap_cfg_reg(F18_1610_KBC0);
406 omap_cfg_reg(D20_1610_KBC1);
407 omap_cfg_reg(D19_1610_KBC2);
408 omap_cfg_reg(E18_1610_KBC3);
409 omap_cfg_reg(C21_1610_KBC4);
410 omap_cfg_reg(G18_1610_KBR0);
411 omap_cfg_reg(F19_1610_KBR1);
412 omap_cfg_reg(H14_1610_KBR2);
413 omap_cfg_reg(E20_1610_KBR3);
414 omap_cfg_reg(E19_1610_KBR4);
415 omap_cfg_reg(N19_1610_KBR5);
417 /* GPIO based LEDs */
418 omap_cfg_reg(P18_1610_GPIO3);
419 omap_cfg_reg(MPUIO4);
421 h2_smc91x_resources[1].start = gpio_to_irq(0);
422 h2_smc91x_resources[1].end = gpio_to_irq(0);
423 platform_add_devices(h2_devices, ARRAY_SIZE(h2_devices));
426 /* ISP1301 IRQ wired at M14 */
427 omap_cfg_reg(M14_1510_GPIO2);
428 h2_i2c_board_info[0].irq = gpio_to_irq(58);
429 omap_register_i2c_bus(1, 100, h2_i2c_board_info,
430 ARRAY_SIZE(h2_i2c_board_info));
431 omap1_usb_init(&h2_usb_config);
434 omapfb_set_lcd_config(&h2_lcd_config);
437 MACHINE_START(OMAP_H2, "TI-H2")
438 /* Maintainer: Imre Deak <imre.deak@nokia.com> */
439 .atag_offset = 0x100,
440 .map_io = omap16xx_map_io,
441 .init_early = omap1_init_early,
442 .init_irq = omap1_init_irq,
443 .handle_irq = omap1_handle_irq,
444 .init_machine = h2_init,
445 .init_late = omap1_init_late,
446 .init_time = omap1_timer_init,
447 .restart = omap1_restart,