arch/arm/boot/dts/qcom-msm8974-lge-nexus5-hammerhead.dts

   1 // SPDX-License-Identifier: GPL-2.0
   2 #include "qcom-msm8974.dtsi"
   3 #include "qcom-pm8841.dtsi"
   4 #include "qcom-pm8941.dtsi"
   5 #include <dt-bindings/input/input.h>
   6 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
   7
   8 / {
   9         model = "LGE MSM 8974 HAMMERHEAD";
  10         compatible = "lge,hammerhead", "qcom,msm8974";
  11
  12         aliases {
  13                 serial0 = &blsp1_uart1;
  14                 serial1 = &blsp2_uart4;
  15         };
  16
  17         chosen {
  18                 stdout-path = "serial0:115200n8";
  19         };
  20
  21         gpio-keys {
  22                 compatible = "gpio-keys";
  23
  24                 pinctrl-names = "default";
  25                 pinctrl-0 = <&gpio_keys_pin_a>;
  26
  27                 volume-up {
  28                         label = "volume_up";
  29                         gpios = <&pm8941_gpios 2 GPIO_ACTIVE_LOW>;
  30                         linux,input-type = <1>;
  31                         linux,code = <KEY_VOLUMEUP>;
  32                 };
  33
  34                 volume-down {
  35                         label = "volume_down";
  36                         gpios = <&pm8941_gpios 3 GPIO_ACTIVE_LOW>;
  37                         linux,input-type = <1>;
  38                         linux,code = <KEY_VOLUMEDOWN>;
  39                 };
  40         };
  41
  42         vreg_wlan: wlan-regulator {
  43                 compatible = "regulator-fixed";
  44
  45                 regulator-name = "wl-reg";
  46                 regulator-min-microvolt = <3300000>;
  47                 regulator-max-microvolt = <3300000>;
  48
  49                 gpio = <&tlmm 26 GPIO_ACTIVE_HIGH>;
  50                 enable-active-high;
  51
  52                 pinctrl-names = "default";
  53                 pinctrl-0 = <&wlan_regulator_pin>;
  54         };
  55 };
  56
  57 &blsp1_i2c1 {
  58         status = "okay";
  59         clock-frequency = <100000>;
  60
  61         charger: bq24192@6b {
  62                 compatible = "ti,bq24192";
  63                 reg = <0x6b>;
  64                 interrupts-extended = <&spmi_bus 0 0xd5 0 IRQ_TYPE_EDGE_FALLING>;
  65
  66                 omit-battery-class;
  67
  68                 usb_otg_vbus: usb-otg-vbus { };
  69         };
  70
  71         fuelgauge: max17048@36 {
  72                 compatible = "maxim,max17048";
  73                 reg = <0x36>;
  74
  75                 maxim,double-soc;
  76                 maxim,rcomp = /bits/ 8 <0x4d>;
  77
  78                 interrupt-parent = <&tlmm>;
  79                 interrupts = <9 IRQ_TYPE_LEVEL_LOW>;
  80
  81                 pinctrl-names = "default";
  82                 pinctrl-0 = <&fuelgauge_pin>;
  83
  84                 maxim,alert-low-soc-level = <2>;
  85         };
  86 };
  87
  88 &blsp1_i2c2 {
  89         status = "okay";
  90         clock-frequency = <355000>;
  91
  92         synaptics@70 {
  93                 compatible = "syna,rmi4-i2c";
  94                 reg = <0x70>;
  95
  96                 interrupts-extended = <&tlmm 5 IRQ_TYPE_EDGE_FALLING>;
  97                 vdd-supply = <&pm8941_l22>;
  98                 vio-supply = <&pm8941_lvs3>;
  99
 100                 pinctrl-names = "default";
 101                 pinctrl-0 = <&touch_pin>;
 102
 103                 #address-cells = <1>;
 104                 #size-cells = <0>;
 105
 106                 rmi4-f01@1 {
 107                         reg = <0x1>;
 108                         syna,nosleep-mode = <1>;
 109                 };
 110
 111                 rmi4-f12@12 {
 112                         reg = <0x12>;
 113                         syna,sensor-type = <1>;
 114                 };
 115         };
 116 };
 117
 118 &blsp1_i2c3 {
 119         status = "okay";
 120         clock-frequency = <100000>;
 121
 122         avago_apds993@39 {
 123                 compatible = "avago,apds9930";
 124                 reg = <0x39>;
 125                 interrupts-extended = <&tlmm 61 IRQ_TYPE_EDGE_FALLING>;
 126                 vdd-supply = <&pm8941_l17>;
 127                 vddio-supply = <&pm8941_lvs1>;
 128                 led-max-microamp = <100000>;
 129                 amstaos,proximity-diodes = <0>;
 130         };
 131 };
 132
 133 &blsp2_i2c5 {
 134         status = "okay";
 135         clock-frequency = <355000>;
 136
 137         led-controller@38 {
 138                 compatible = "ti,lm3630a";
 139                 status = "okay";
 140                 reg = <0x38>;
 141
 142                 #address-cells = <1>;
 143                 #size-cells = <0>;
 144
 145                 led@0 {
 146                         reg = <0>;
 147                         led-sources = <0 1>;
 148                         label = "lcd-backlight";
 149                         default-brightness = <200>;
 150                 };
 151         };
 152 };
 153
 154 &blsp2_i2c6 {
 155         status = "okay";
 156         clock-frequency = <100000>;
 157
 158         mpu6515@68 {
 159                 compatible = "invensense,mpu6515";
 160                 reg = <0x68>;
 161                 interrupts-extended = <&tlmm 73 IRQ_TYPE_EDGE_FALLING>;
 162                 vddio-supply = <&pm8941_lvs1>;
 163
 164                 pinctrl-names = "default";
 165                 pinctrl-0 = <&mpu6515_pin>;
 166
 167                 mount-matrix = "0", "-1", "0",
 168                                 "-1", "0", "0",
 169                                 "0", "0", "1";
 170
 171                 i2c-gate {
 172                         #address-cells = <1>;
 173                         #size-cells = <0>;
 174                         ak8963@f {
 175                                 compatible = "asahi-kasei,ak8963";
 176                                 reg = <0x0f>;
 177                                 gpios = <&tlmm 67 0>;
 178                                 vid-supply = <&pm8941_lvs1>;
 179                                 vdd-supply = <&pm8941_l17>;
 180                         };
 181
 182                         bmp280@76 {
 183                                 compatible = "bosch,bmp280";
 184                                 reg = <0x76>;
 185                                 vdda-supply = <&pm8941_lvs1>;
 186                                 vddd-supply = <&pm8941_l17>;
 187                         };
 188                 };
 189         };
 190 };
 191
 192 &blsp1_uart1 {
 193         status = "okay";
 194 };
 195
 196 &blsp2_uart4 {
 197         status = "okay";
 198
 199         bluetooth {
 200                 compatible = "brcm,bcm43438-bt";
 201                 max-speed = <3000000>;
 202
 203                 pinctrl-names = "default";
 204                 pinctrl-0 = <&bt_pin>;
 205
 206                 host-wakeup-gpios = <&tlmm 42 GPIO_ACTIVE_HIGH>;
 207                 device-wakeup-gpios = <&tlmm 62 GPIO_ACTIVE_HIGH>;
 208                 shutdown-gpios = <&tlmm 41 GPIO_ACTIVE_HIGH>;
 209         };
 210 };
 211
 212 &dsi0 {
 213         status = "okay";
 214
 215         vdda-supply = <&pm8941_l2>;
 216         vdd-supply = <&pm8941_lvs3>;
 217         vddio-supply = <&pm8941_l12>;
 218
 219         panel: panel@0 {
 220                 reg = <0>;
 221                 compatible = "lg,acx467akm-7";
 222
 223                 pinctrl-names = "default";
 224                 pinctrl-0 = <&panel_pin>;
 225
 226                 port {
 227                         panel_in: endpoint {
 228                                 remote-endpoint = <&dsi0_out>;
 229                         };
 230                 };
 231         };
 232 };
 233
 234 &dsi0_out {
 235         remote-endpoint = <&panel_in>;
 236         data-lanes = <0 1 2 3>;
 237 };
 238
 239 &dsi0_phy {
 240         status = "okay";
 241
 242         vddio-supply = <&pm8941_l12>;
 243 };
 244
 245 &mdss {
 246         status = "okay";
 247 };
 248
 249 &otg {
 250         status = "okay";
 251
 252         phys = <&usb_hs1_phy>;
 253         phy-select = <&tcsr 0xb000 0>;
 254
 255         extcon = <&charger>, <&usb_id>;
 256         vbus-supply = <&usb_otg_vbus>;
 257
 258         hnp-disable;
 259         srp-disable;
 260         adp-disable;
 261
 262         ulpi {
 263                 phy@a {
 264                         status = "okay";
 265
 266                         v1p8-supply = <&pm8941_l6>;
 267                         v3p3-supply = <&pm8941_l24>;
 268
 269                         qcom,init-seq = /bits/ 8 <0x1 0x64>;
 270                 };
 271         };
 272 };
 273
 274 &pm8941_gpios {
 275         gpio_keys_pin_a: gpio-keys-active {
 276                 pins = "gpio2", "gpio3";
 277                 function = "normal";
 278
 279                 bias-pull-up;
 280                 power-source = <PM8941_GPIO_S3>;
 281         };
 282
 283         fuelgauge_pin: fuelgauge-int {
 284                 pins = "gpio9";
 285                 function = "normal";
 286
 287                 bias-disable;
 288                 input-enable;
 289                 power-source = <PM8941_GPIO_S3>;
 290         };
 291
 292         wlan_sleep_clk_pin: wl-sleep-clk {
 293                 pins = "gpio16";
 294                 function = "func2";
 295
 296                 output-high;
 297                 power-source = <PM8941_GPIO_S3>;
 298         };
 299
 300         wlan_regulator_pin: wl-reg-active {
 301                 pins = "gpio17";
 302                 function = "normal";
 303
 304                 bias-disable;
 305                 power-source = <PM8941_GPIO_S3>;
 306         };
 307
 308         otg {
 309                 gpio-hog;
 310                 gpios = <35 GPIO_ACTIVE_HIGH>;
 311                 output-high;
 312                 line-name = "otg-gpio";
 313         };
 314 };
 315
 316 &rpm_requests {
 317         pm8841-regulators {
 318                 compatible = "qcom,rpm-pm8841-regulators";
 319
 320                 pm8841_s1: s1 {
 321                         regulator-min-microvolt = <675000>;
 322                         regulator-max-microvolt = <1050000>;
 323                 };
 324
 325                 pm8841_s2: s2 {
 326                         regulator-min-microvolt = <500000>;
 327                         regulator-max-microvolt = <1050000>;
 328                 };
 329
 330                 pm8841_s3: s3 {
 331                         regulator-min-microvolt = <1050000>;
 332                         regulator-max-microvolt = <1050000>;
 333                 };
 334
 335                 pm8841_s4: s4 {
 336                         regulator-min-microvolt = <815000>;
 337                         regulator-max-microvolt = <900000>;
 338                 };
 339         };
 340
 341         pm8941-regulators {
 342                 compatible = "qcom,rpm-pm8941-regulators";
 343
 344                 vdd_l1_l3-supply = <&pm8941_s1>;
 345                 vdd_l2_lvs1_2_3-supply = <&pm8941_s3>;
 346                 vdd_l4_l11-supply = <&pm8941_s1>;
 347                 vdd_l5_l7-supply = <&pm8941_s2>;
 348                 vdd_l6_l12_l14_l15-supply = <&pm8941_s2>;
 349                 vdd_l8_l16_l18_l19-supply = <&vreg_vph_pwr>;
 350                 vdd_l9_l10_l17_l22-supply = <&vreg_boost>;
 351                 vdd_l13_l20_l23_l24-supply = <&vreg_boost>;
 352                 vdd_l21-supply = <&vreg_boost>;
 353
 354                 pm8941_s1: s1 {
 355                         regulator-min-microvolt = <1300000>;
 356                         regulator-max-microvolt = <1300000>;
 357                         regulator-always-on;
 358                         regulator-boot-on;
 359                 };
 360
 361                 pm8941_s2: s2 {
 362                         regulator-min-microvolt = <2150000>;
 363                         regulator-max-microvolt = <2150000>;
 364                         regulator-boot-on;
 365                 };
 366
 367                 pm8941_s3: s3 {
 368                         regulator-min-microvolt = <1800000>;
 369                         regulator-max-microvolt = <1800000>;
 370                         regulator-always-on;
 371                         regulator-boot-on;
 372                 };
 373
 374                 pm8941_l1: l1 {
 375                         regulator-min-microvolt = <1225000>;
 376                         regulator-max-microvolt = <1225000>;
 377                         regulator-always-on;
 378                         regulator-boot-on;
 379                 };
 380
 381                 pm8941_l2: l2 {
 382                         regulator-min-microvolt = <1200000>;
 383                         regulator-max-microvolt = <1200000>;
 384                 };
 385
 386                 pm8941_l3: l3 {
 387                         regulator-min-microvolt = <1225000>;
 388                         regulator-max-microvolt = <1225000>;
 389                 };
 390
 391                 pm8941_l4: l4 {
 392                         regulator-min-microvolt = <1225000>;
 393                         regulator-max-microvolt = <1225000>;
 394                 };
 395
 396                 pm8941_l5: l5 {
 397                         regulator-min-microvolt = <1800000>;
 398                         regulator-max-microvolt = <1800000>;
 399                 };
 400
 401                 pm8941_l6: l6 {
 402                         regulator-min-microvolt = <1800000>;
 403                         regulator-max-microvolt = <1800000>;
 404                         regulator-boot-on;
 405                 };
 406
 407                 pm8941_l7: l7 {
 408                         regulator-min-microvolt = <1800000>;
 409                         regulator-max-microvolt = <1800000>;
 410                         regulator-boot-on;
 411                 };
 412
 413                 pm8941_l8: l8 {
 414                         regulator-min-microvolt = <1800000>;
 415                         regulator-max-microvolt = <1800000>;
 416                 };
 417
 418                 pm8941_l9: l9 {
 419                         regulator-min-microvolt = <1800000>;
 420                         regulator-max-microvolt = <2950000>;
 421                 };
 422
 423                 pm8941_l10: l10 {
 424                         regulator-min-microvolt = <1800000>;
 425                         regulator-max-microvolt = <2950000>;
 426                 };
 427
 428                 pm8941_l11: l11 {
 429                         regulator-min-microvolt = <1300000>;
 430                         regulator-max-microvolt = <1300000>;
 431                 };
 432
 433                 pm8941_l12: l12 {
 434                         regulator-min-microvolt = <1800000>;
 435                         regulator-max-microvolt = <1800000>;
 436                         regulator-always-on;
 437                         regulator-boot-on;
 438                 };
 439
 440                 pm8941_l13: l13 {
 441                         regulator-min-microvolt = <1800000>;
 442                         regulator-max-microvolt = <2950000>;
 443                         regulator-boot-on;
 444                 };
 445
 446                 pm8941_l14: l14 {
 447                         regulator-min-microvolt = <1800000>;
 448                         regulator-max-microvolt = <1800000>;
 449                 };
 450
 451                 pm8941_l15: l15 {
 452                         regulator-min-microvolt = <2050000>;
 453                         regulator-max-microvolt = <2050000>;
 454                 };
 455
 456                 pm8941_l16: l16 {
 457                         regulator-min-microvolt = <2700000>;
 458                         regulator-max-microvolt = <2700000>;
 459                 };
 460
 461                 pm8941_l17: l17 {
 462                         regulator-min-microvolt = <2850000>;
 463                         regulator-max-microvolt = <2850000>;
 464                 };
 465
 466                 pm8941_l18: l18 {
 467                         regulator-min-microvolt = <2850000>;
 468                         regulator-max-microvolt = <2850000>;
 469                 };
 470
 471                 pm8941_l19: l19 {
 472                         regulator-min-microvolt = <3000000>;
 473                         regulator-max-microvolt = <3300000>;
 474                 };
 475
 476                 pm8941_l20: l20 {
 477                         regulator-min-microvolt = <2950000>;
 478                         regulator-max-microvolt = <2950000>;
 479                         regulator-system-load = <200000>;
 480                         regulator-allow-set-load;
 481                         regulator-boot-on;
 482                 };
 483
 484                 pm8941_l21: l21 {
 485                         regulator-min-microvolt = <2950000>;
 486                         regulator-max-microvolt = <2950000>;
 487                         regulator-boot-on;
 488                 };
 489
 490                 pm8941_l22: l22 {
 491                         regulator-min-microvolt = <3000000>;
 492                         regulator-max-microvolt = <3300000>;
 493                 };
 494
 495                 pm8941_l23: l23 {
 496                         regulator-min-microvolt = <3000000>;
 497                         regulator-max-microvolt = <3000000>;
 498                 };
 499
 500                 pm8941_l24: l24 {
 501                         regulator-min-microvolt = <3075000>;
 502                         regulator-max-microvolt = <3075000>;
 503                         regulator-boot-on;
 504                 };
 505
 506                 pm8941_lvs1: lvs1 {};
 507                 pm8941_lvs3: lvs3 {};
 508         };
 509 };
 510
 511 &sdhc_1 {
 512         status = "okay";
 513
 514         vmmc-supply = <&pm8941_l20>;
 515         vqmmc-supply = <&pm8941_s3>;
 516
 517         pinctrl-names = "default", "sleep";
 518         pinctrl-0 = <&sdc1_on>;
 519         pinctrl-1 = <&sdc1_off>;
 520 };
 521
 522 &sdhc_2 {
 523         status = "okay";
 524
 525         max-frequency = <100000000>;
 526         vmmc-supply = <&vreg_wlan>;
 527         vqmmc-supply = <&pm8941_s3>;
 528         non-removable;
 529
 530         pinctrl-names = "default", "sleep";
 531         pinctrl-0 = <&sdc2_on>;
 532         pinctrl-1 = <&sdc2_off>;
 533
 534         bcrmf@1 {
 535                 compatible = "brcm,bcm4339-fmac", "brcm,bcm4329-fmac";
 536                 reg = <1>;
 537
 538                 brcm,drive-strength = <10>;
 539
 540                 pinctrl-names = "default";
 541                 pinctrl-0 = <&wlan_sleep_clk_pin>;
 542         };
 543 };
 544
 545 &tlmm {
 546         sdc1_on: sdc1-on {
 547                 clk {
 548                         pins = "sdc1_clk";
 549                         drive-strength = <16>;
 550                         bias-disable;
 551                 };
 552
 553                 cmd-data {
 554                         pins = "sdc1_cmd", "sdc1_data";
 555                         drive-strength = <10>;
 556                         bias-pull-up;
 557                 };
 558         };
 559
 560         sdc2_on: sdc2-on {
 561                 clk {
 562                         pins = "sdc2_clk";
 563                         drive-strength = <6>;
 564                         bias-disable;
 565                 };
 566
 567                 cmd-data {
 568                         pins = "sdc2_cmd", "sdc2_data";
 569                         drive-strength = <6>;
 570                         bias-pull-up;
 571                 };
 572         };
 573
 574         mpu6515_pin: mpu6515 {
 575                 pins = "gpio73";
 576                 function = "gpio";
 577                 bias-disable;
 578                 input-enable;
 579         };
 580
 581         touch_pin: touch {
 582                 int {
 583                         pins = "gpio5";
 584                         function = "gpio";
 585
 586                         drive-strength = <2>;
 587                         bias-disable;
 588                         input-enable;
 589                 };
 590
 591                 reset {
 592                         pins = "gpio8";
 593                         function = "gpio";
 594
 595                         drive-strength = <2>;
 596                         bias-pull-up;
 597                 };
 598         };
 599
 600         panel_pin: panel {
 601                 pins = "gpio12";
 602                 function = "mdp_vsync";
 603                 drive-strength = <2>;
 604                 bias-disable;
 605         };
 606
 607         bt_pin: bt {
 608                 hostwake {
 609                         pins = "gpio42";
 610                         function = "gpio";
 611                 };
 612
 613                 devwake {
 614                         pins = "gpio62";
 615                         function = "gpio";
 616                 };
 617
 618                 shutdown {
 619                         pins = "gpio41";
 620                         function = "gpio";
 621                 };
 622         };
 623 };