arch/arm/boot/dts/qcom-apq8064.dtsi

   1 // SPDX-License-Identifier: GPL-2.0
   2 /dts-v1/;
   3
   4 #include <dt-bindings/clock/qcom,gcc-msm8960.h>
   5 #include <dt-bindings/reset/qcom,gcc-msm8960.h>
   6 #include <dt-bindings/clock/qcom,mmcc-msm8960.h>
   7 #include <dt-bindings/clock/qcom,rpmcc.h>
   8 #include <dt-bindings/soc/qcom,gsbi.h>
   9 #include <dt-bindings/interrupt-controller/irq.h>
  10 #include <dt-bindings/interrupt-controller/arm-gic.h>
  11 / {
  12         #address-cells = <1>;
  13         #size-cells = <1>;
  14         model = "Qualcomm APQ8064";
  15         compatible = "qcom,apq8064";
  16         interrupt-parent = <&intc>;
  17
  18         reserved-memory {
  19                 #address-cells = <1>;
  20                 #size-cells = <1>;
  21                 ranges;
  22
  23                 smem_region: smem@80000000 {
  24                         reg = <0x80000000 0x200000>;
  25                         no-map;
  26                 };
  27
  28                 wcnss_mem: wcnss@8f000000 {
  29                         reg = <0x8f000000 0x700000>;
  30                         no-map;
  31                 };
  32         };
  33
  34         cpus {
  35                 #address-cells = <1>;
  36                 #size-cells = <0>;
  37
  38                 CPU0: cpu@0 {
  39                         compatible = "qcom,krait";
  40                         enable-method = "qcom,kpss-acc-v1";
  41                         device_type = "cpu";
  42                         reg = <0>;
  43                         next-level-cache = <&L2>;
  44                         qcom,acc = <&acc0>;
  45                         qcom,saw = <&saw0>;
  46                         cpu-idle-states = <&CPU_SPC>;
  47                 };
  48
  49                 CPU1: cpu@1 {
  50                         compatible = "qcom,krait";
  51                         enable-method = "qcom,kpss-acc-v1";
  52                         device_type = "cpu";
  53                         reg = <1>;
  54                         next-level-cache = <&L2>;
  55                         qcom,acc = <&acc1>;
  56                         qcom,saw = <&saw1>;
  57                         cpu-idle-states = <&CPU_SPC>;
  58                 };
  59
  60                 CPU2: cpu@2 {
  61                         compatible = "qcom,krait";
  62                         enable-method = "qcom,kpss-acc-v1";
  63                         device_type = "cpu";
  64                         reg = <2>;
  65                         next-level-cache = <&L2>;
  66                         qcom,acc = <&acc2>;
  67                         qcom,saw = <&saw2>;
  68                         cpu-idle-states = <&CPU_SPC>;
  69                 };
  70
  71                 CPU3: cpu@3 {
  72                         compatible = "qcom,krait";
  73                         enable-method = "qcom,kpss-acc-v1";
  74                         device_type = "cpu";
  75                         reg = <3>;
  76                         next-level-cache = <&L2>;
  77                         qcom,acc = <&acc3>;
  78                         qcom,saw = <&saw3>;
  79                         cpu-idle-states = <&CPU_SPC>;
  80                 };
  81
  82                 L2: l2-cache {
  83                         compatible = "cache";
  84                         cache-level = <2>;
  85                 };
  86
  87                 idle-states {
  88                         CPU_SPC: spc {
  89                                 compatible = "qcom,idle-state-spc",
  90                                                 "arm,idle-state";
  91                                 entry-latency-us = <400>;
  92                                 exit-latency-us = <900>;
  93                                 min-residency-us = <3000>;
  94                         };
  95                 };
  96         };
  97
  98         memory@0 {
  99                 device_type = "memory";
 100                 reg = <0x0 0x0>;
 101         };
 102
 103         thermal-zones {
 104                 cpu0-thermal {
 105                         polling-delay-passive = <250>;
 106                         polling-delay = <1000>;
 107
 108                         thermal-sensors = <&gcc 7>;
 109                         coefficients = <1199 0>;
 110
 111                         trips {
 112                                 cpu_alert0: trip0 {
 113                                         temperature = <75000>;
 114                                         hysteresis = <2000>;
 115                                         type = "passive";
 116                                 };
 117                                 cpu_crit0: trip1 {
 118                                         temperature = <110000>;
 119                                         hysteresis = <2000>;
 120                                         type = "critical";
 121                                 };
 122                         };
 123                 };
 124
 125                 cpu1-thermal {
 126                         polling-delay-passive = <250>;
 127                         polling-delay = <1000>;
 128
 129                         thermal-sensors = <&gcc 8>;
 130                         coefficients = <1132 0>;
 131
 132                         trips {
 133                                 cpu_alert1: trip0 {
 134                                         temperature = <75000>;
 135                                         hysteresis = <2000>;
 136                                         type = "passive";
 137                                 };
 138                                 cpu_crit1: trip1 {
 139                                         temperature = <110000>;
 140                                         hysteresis = <2000>;
 141                                         type = "critical";
 142                                 };
 143                         };
 144                 };
 145
 146                 cpu2-thermal {
 147                         polling-delay-passive = <250>;
 148                         polling-delay = <1000>;
 149
 150                         thermal-sensors = <&gcc 9>;
 151                         coefficients = <1199 0>;
 152
 153                         trips {
 154                                 cpu_alert2: trip0 {
 155                                         temperature = <75000>;
 156                                         hysteresis = <2000>;
 157                                         type = "passive";
 158                                 };
 159                                 cpu_crit2: trip1 {
 160                                         temperature = <110000>;
 161                                         hysteresis = <2000>;
 162                                         type = "critical";
 163                                 };
 164                         };
 165                 };
 166
 167                 cpu3-thermal {
 168                         polling-delay-passive = <250>;
 169                         polling-delay = <1000>;
 170
 171                         thermal-sensors = <&gcc 10>;
 172                         coefficients = <1132 0>;
 173
 174                         trips {
 175                                 cpu_alert3: trip0 {
 176                                         temperature = <75000>;
 177                                         hysteresis = <2000>;
 178                                         type = "passive";
 179                                 };
 180                                 cpu_crit3: trip1 {
 181                                         temperature = <110000>;
 182                                         hysteresis = <2000>;
 183                                         type = "critical";
 184                                 };
 185                         };
 186                 };
 187         };
 188
 189         cpu-pmu {
 190                 compatible = "qcom,krait-pmu";
 191                 interrupts = <1 10 0x304>;
 192         };
 193
 194         clocks {
 195                 cxo_board: cxo_board {
 196                         compatible = "fixed-clock";
 197                         #clock-cells = <0>;
 198                         clock-frequency = <19200000>;
 199                 };
 200
 201                 pxo_board: pxo_board {
 202                         compatible = "fixed-clock";
 203                         #clock-cells = <0>;
 204                         clock-frequency = <27000000>;
 205                 };
 206
 207                 sleep_clk: sleep_clk {
 208                         compatible = "fixed-clock";
 209                         #clock-cells = <0>;
 210                         clock-frequency = <32768>;
 211                 };
 212         };
 213
 214         sfpb_mutex: hwmutex {
 215                 compatible = "qcom,sfpb-mutex";
 216                 syscon = <&sfpb_wrapper_mutex 0x604 0x4>;
 217                 #hwlock-cells = <1>;
 218         };
 219
 220         smem {
 221                 compatible = "qcom,smem";
 222                 memory-region = <&smem_region>;
 223
 224                 hwlocks = <&sfpb_mutex 3>;
 225         };
 226
 227         smd {
 228                 compatible = "qcom,smd";
 229
 230                 modem-edge {
 231                         interrupts = <0 37 IRQ_TYPE_EDGE_RISING>;
 232
 233                         qcom,ipc = <&l2cc 8 3>;
 234                         qcom,smd-edge = <0>;
 235
 236                         status = "disabled";
 237                 };
 238
 239                 q6-edge {
 240                         interrupts = <0 90 IRQ_TYPE_EDGE_RISING>;
 241
 242                         qcom,ipc = <&l2cc 8 15>;
 243                         qcom,smd-edge = <1>;
 244
 245                         status = "disabled";
 246                 };
 247
 248                 dsps-edge {
 249                         interrupts = <0 138 IRQ_TYPE_EDGE_RISING>;
 250
 251                         qcom,ipc = <&sps_sic_non_secure 0x4080 0>;
 252                         qcom,smd-edge = <3>;
 253
 254                         status = "disabled";
 255                 };
 256
 257                 riva-edge {
 258                         interrupts = <0 198 IRQ_TYPE_EDGE_RISING>;
 259
 260                         qcom,ipc = <&l2cc 8 25>;
 261                         qcom,smd-edge = <6>;
 262
 263                         status = "disabled";
 264                 };
 265         };
 266
 267         smsm {
 268                 compatible = "qcom,smsm";
 269
 270                 #address-cells = <1>;
 271                 #size-cells = <0>;
 272
 273                 qcom,ipc-1 = <&l2cc 8 4>;
 274                 qcom,ipc-2 = <&l2cc 8 14>;
 275                 qcom,ipc-3 = <&l2cc 8 23>;
 276                 qcom,ipc-4 = <&sps_sic_non_secure 0x4094 0>;
 277
 278                 apps_smsm: apps@0 {
 279                         reg = <0>;
 280                         #qcom,smem-state-cells = <1>;
 281                 };
 282
 283                 modem_smsm: modem@1 {
 284                         reg = <1>;
 285                         interrupts = <0 38 IRQ_TYPE_EDGE_RISING>;
 286
 287                         interrupt-controller;
 288                         #interrupt-cells = <2>;
 289                 };
 290
 291                 q6_smsm: q6@2 {
 292                         reg = <2>;
 293                         interrupts = <0 89 IRQ_TYPE_EDGE_RISING>;
 294
 295                         interrupt-controller;
 296                         #interrupt-cells = <2>;
 297                 };
 298
 299                 wcnss_smsm: wcnss@3 {
 300                         reg = <3>;
 301                         interrupts = <0 204 IRQ_TYPE_EDGE_RISING>;
 302
 303                         interrupt-controller;
 304                         #interrupt-cells = <2>;
 305                 };
 306
 307                 dsps_smsm: dsps@4 {
 308                         reg = <4>;
 309                         interrupts = <0 137 IRQ_TYPE_EDGE_RISING>;
 310
 311                         interrupt-controller;
 312                         #interrupt-cells = <2>;
 313                 };
 314         };
 315
 316         firmware {
 317                 scm {
 318                         compatible = "qcom,scm-apq8064";
 319
 320                         clocks = <&rpmcc RPM_DAYTONA_FABRIC_CLK>;
 321                         clock-names = "core";
 322                 };
 323         };
 324
 325
 326         /*
 327          * These channels from the ADC are simply hardware monitors.
 328          * That is why the ADC is referred to as "HKADC" - HouseKeeping
 329          * ADC.
 330          */
 331         iio-hwmon {
 332                 compatible = "iio-hwmon";
 333                 io-channels = <&xoadc 0x00 0x01>, /* Battery */
 334                             <&xoadc 0x00 0x02>, /* DC in (charger) */
 335                             <&xoadc 0x00 0x04>, /* VPH the main system voltage */
 336                             <&xoadc 0x00 0x0b>, /* Die temperature */
 337                             <&xoadc 0x00 0x0c>, /* Reference voltage 1.25V */
 338                             <&xoadc 0x00 0x0d>, /* Reference voltage 0.625V */
 339                             <&xoadc 0x00 0x0e>; /* Charger temperature */
 340         };
 341
 342         soc: soc {
 343                 #address-cells = <1>;
 344                 #size-cells = <1>;
 345                 ranges;
 346                 compatible = "simple-bus";
 347
 348                 tlmm_pinmux: pinctrl@800000 {
 349                         compatible = "qcom,apq8064-pinctrl";
 350                         reg = <0x800000 0x4000>;
 351
 352                         gpio-controller;
 353                         gpio-ranges = <&tlmm_pinmux 0 0 90>;
 354                         #gpio-cells = <2>;
 355                         interrupt-controller;
 356                         #interrupt-cells = <2>;
 357                         interrupts = <0 16 IRQ_TYPE_LEVEL_HIGH>;
 358
 359                         pinctrl-names = "default";
 360                         pinctrl-0 = <&ps_hold>;
 361                 };
 362
 363                 sfpb_wrapper_mutex: syscon@1200000 {
 364                         compatible = "syscon";
 365                         reg = <0x01200000 0x8000>;
 366                 };
 367
 368                 intc: interrupt-controller@2000000 {
 369                         compatible = "qcom,msm-qgic2";
 370                         interrupt-controller;
 371                         #interrupt-cells = <3>;
 372                         reg = <0x02000000 0x1000>,
 373                               <0x02002000 0x1000>;
 374                 };
 375
 376                 timer@200a000 {
 377                         compatible = "qcom,kpss-timer",
 378                                      "qcom,kpss-wdt-apq8064", "qcom,msm-timer";
 379                         interrupts = <1 1 0x301>,
 380                                      <1 2 0x301>,
 381                                      <1 3 0x301>;
 382                         reg = <0x0200a000 0x100>;
 383                         clock-frequency = <27000000>,
 384                                           <32768>;
 385                         cpu-offset = <0x80000>;
 386                 };
 387
 388                 acc0: clock-controller@2088000 {
 389                         compatible = "qcom,kpss-acc-v1";
 390                         reg = <0x02088000 0x1000>, <0x02008000 0x1000>;
 391                 };
 392
 393                 acc1: clock-controller@2098000 {
 394                         compatible = "qcom,kpss-acc-v1";
 395                         reg = <0x02098000 0x1000>, <0x02008000 0x1000>;
 396                 };
 397
 398                 acc2: clock-controller@20a8000 {
 399                         compatible = "qcom,kpss-acc-v1";
 400                         reg = <0x020a8000 0x1000>, <0x02008000 0x1000>;
 401                 };
 402
 403                 acc3: clock-controller@20b8000 {
 404                         compatible = "qcom,kpss-acc-v1";
 405                         reg = <0x020b8000 0x1000>, <0x02008000 0x1000>;
 406                 };
 407
 408                 saw0: power-controller@2089000 {
 409                         compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
 410                         reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
 411                         regulator;
 412                 };
 413
 414                 saw1: power-controller@2099000 {
 415                         compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
 416                         reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
 417                         regulator;
 418                 };
 419
 420                 saw2: power-controller@20a9000 {
 421                         compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
 422                         reg = <0x020a9000 0x1000>, <0x02009000 0x1000>;
 423                         regulator;
 424                 };
 425
 426                 saw3: power-controller@20b9000 {
 427                         compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
 428                         reg = <0x020b9000 0x1000>, <0x02009000 0x1000>;
 429                         regulator;
 430                 };
 431
 432                 sps_sic_non_secure: sps-sic-non-secure@12100000 {
 433                         compatible      = "syscon";
 434                         reg             = <0x12100000 0x10000>;
 435                 };
 436
 437                 gsbi1: gsbi@12440000 {
 438                         status = "disabled";
 439                         compatible = "qcom,gsbi-v1.0.0";
 440                         cell-index = <1>;
 441                         reg = <0x12440000 0x100>;
 442                         clocks = <&gcc GSBI1_H_CLK>;
 443                         clock-names = "iface";
 444                         #address-cells = <1>;
 445                         #size-cells = <1>;
 446                         ranges;
 447
 448                         syscon-tcsr = <&tcsr>;
 449
 450                         gsbi1_serial: serial@12450000 {
 451                                 compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
 452                                 reg = <0x12450000 0x100>,
 453                                       <0x12400000 0x03>;
 454                                 interrupts = <0 193 IRQ_TYPE_LEVEL_HIGH>;
 455                                 clocks = <&gcc GSBI1_UART_CLK>, <&gcc GSBI1_H_CLK>;
 456                                 clock-names = "core", "iface";
 457                                 status = "disabled";
 458                         };
 459
 460                         gsbi1_i2c: i2c@12460000 {
 461                                 compatible = "qcom,i2c-qup-v1.1.1";
 462                                 pinctrl-0 = <&i2c1_pins>;
 463                                 pinctrl-1 = <&i2c1_pins_sleep>;
 464                                 pinctrl-names = "default", "sleep";
 465                                 reg = <0x12460000 0x1000>;
 466                                 interrupts = <0 194 IRQ_TYPE_LEVEL_HIGH>;
 467                                 clocks = <&gcc GSBI1_QUP_CLK>, <&gcc GSBI1_H_CLK>;
 468                                 clock-names = "core", "iface";
 469                                 #address-cells = <1>;
 470                                 #size-cells = <0>;
 471                                 status = "disabled";
 472                         };
 473
 474                 };
 475
 476                 gsbi2: gsbi@12480000 {
 477                         status = "disabled";
 478                         compatible = "qcom,gsbi-v1.0.0";
 479                         cell-index = <2>;
 480                         reg = <0x12480000 0x100>;
 481                         clocks = <&gcc GSBI2_H_CLK>;
 482                         clock-names = "iface";
 483                         #address-cells = <1>;
 484                         #size-cells = <1>;
 485                         ranges;
 486
 487                         syscon-tcsr = <&tcsr>;
 488
 489                         gsbi2_i2c: i2c@124a0000 {
 490                                 compatible = "qcom,i2c-qup-v1.1.1";
 491                                 reg = <0x124a0000 0x1000>;
 492                                 pinctrl-0 = <&i2c2_pins>;
 493                                 pinctrl-1 = <&i2c2_pins_sleep>;
 494                                 pinctrl-names = "default", "sleep";
 495                                 interrupts = <0 196 IRQ_TYPE_LEVEL_HIGH>;
 496                                 clocks = <&gcc GSBI2_QUP_CLK>, <&gcc GSBI2_H_CLK>;
 497                                 clock-names = "core", "iface";
 498                                 #address-cells = <1>;
 499                                 #size-cells = <0>;
 500                                 status = "disabled";
 501                         };
 502                 };
 503
 504                 gsbi3: gsbi@16200000 {
 505                         status = "disabled";
 506                         compatible = "qcom,gsbi-v1.0.0";
 507                         cell-index = <3>;
 508                         reg = <0x16200000 0x100>;
 509                         clocks = <&gcc GSBI3_H_CLK>;
 510                         clock-names = "iface";
 511                         #address-cells = <1>;
 512                         #size-cells = <1>;
 513                         ranges;
 514                         gsbi3_i2c: i2c@16280000 {
 515                                 compatible = "qcom,i2c-qup-v1.1.1";
 516                                 pinctrl-0 = <&i2c3_pins>;
 517                                 pinctrl-1 = <&i2c3_pins_sleep>;
 518                                 pinctrl-names = "default", "sleep";
 519                                 reg = <0x16280000 0x1000>;
 520                                 interrupts = <GIC_SPI 151 IRQ_TYPE_LEVEL_HIGH>;
 521                                 clocks = <&gcc GSBI3_QUP_CLK>,
 522                                          <&gcc GSBI3_H_CLK>;
 523                                 clock-names = "core", "iface";
 524                                 #address-cells = <1>;
 525                                 #size-cells = <0>;
 526                                 status = "disabled";
 527                         };
 528                 };
 529
 530                 gsbi4: gsbi@16300000 {
 531                         status = "disabled";
 532                         compatible = "qcom,gsbi-v1.0.0";
 533                         cell-index = <4>;
 534                         reg = <0x16300000 0x03>;
 535                         clocks = <&gcc GSBI4_H_CLK>;
 536                         clock-names = "iface";
 537                         #address-cells = <1>;
 538                         #size-cells = <1>;
 539                         ranges;
 540
 541                         gsbi4_i2c: i2c@16380000 {
 542                                 compatible = "qcom,i2c-qup-v1.1.1";
 543                                 pinctrl-0 = <&i2c4_pins>;
 544                                 pinctrl-1 = <&i2c4_pins_sleep>;
 545                                 pinctrl-names = "default", "sleep";
 546                                 reg = <0x16380000 0x1000>;
 547                                 interrupts = <GIC_SPI 153 IRQ_TYPE_LEVEL_HIGH>;
 548                                 clocks = <&gcc GSBI4_QUP_CLK>,
 549                                          <&gcc GSBI4_H_CLK>;
 550                                 clock-names = "core", "iface";
 551                                 status = "disabled";
 552                         };
 553                 };
 554
 555                 gsbi5: gsbi@1a200000 {
 556                         status = "disabled";
 557                         compatible = "qcom,gsbi-v1.0.0";
 558                         cell-index = <5>;
 559                         reg = <0x1a200000 0x03>;
 560                         clocks = <&gcc GSBI5_H_CLK>;
 561                         clock-names = "iface";
 562                         #address-cells = <1>;
 563                         #size-cells = <1>;
 564                         ranges;
 565
 566                         gsbi5_serial: serial@1a240000 {
 567                                 compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
 568                                 reg = <0x1a240000 0x100>,
 569                                       <0x1a200000 0x03>;
 570                                 interrupts = <0 154 IRQ_TYPE_LEVEL_HIGH>;
 571                                 clocks = <&gcc GSBI5_UART_CLK>, <&gcc GSBI5_H_CLK>;
 572                                 clock-names = "core", "iface";
 573                                 status = "disabled";
 574                         };
 575
 576                         gsbi5_spi: spi@1a280000 {
 577                                 compatible = "qcom,spi-qup-v1.1.1";
 578                                 reg = <0x1a280000 0x1000>;
 579                                 interrupts = <0 155 IRQ_TYPE_LEVEL_HIGH>;
 580                                 pinctrl-0 = <&spi5_default>;
 581                                 pinctrl-1 = <&spi5_sleep>;
 582                                 pinctrl-names = "default", "sleep";
 583                                 clocks = <&gcc GSBI5_QUP_CLK>, <&gcc GSBI5_H_CLK>;
 584                                 clock-names = "core", "iface";
 585                                 status = "disabled";
 586                                 #address-cells = <1>;
 587                                 #size-cells = <0>;
 588                         };
 589                 };
 590
 591                 gsbi6: gsbi@16500000 {
 592                         status = "disabled";
 593                         compatible = "qcom,gsbi-v1.0.0";
 594                         cell-index = <6>;
 595                         reg = <0x16500000 0x03>;
 596                         clocks = <&gcc GSBI6_H_CLK>;
 597                         clock-names = "iface";
 598                         #address-cells = <1>;
 599                         #size-cells = <1>;
 600                         ranges;
 601
 602                         gsbi6_serial: serial@16540000 {
 603                                 compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
 604                                 reg = <0x16540000 0x100>,
 605                                       <0x16500000 0x03>;
 606                                 interrupts = <0 156 IRQ_TYPE_LEVEL_HIGH>;
 607                                 clocks = <&gcc GSBI6_UART_CLK>, <&gcc GSBI6_H_CLK>;
 608                                 clock-names = "core", "iface";
 609                                 status = "disabled";
 610                         };
 611
 612                         gsbi6_i2c: i2c@16580000 {
 613                                 compatible = "qcom,i2c-qup-v1.1.1";
 614                                 pinctrl-0 = <&i2c6_pins>;
 615                                 pinctrl-1 = <&i2c6_pins_sleep>;
 616                                 pinctrl-names = "default", "sleep";
 617                                 reg = <0x16580000 0x1000>;
 618                                 interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
 619                                 clocks = <&gcc GSBI6_QUP_CLK>,
 620                                          <&gcc GSBI6_H_CLK>;
 621                                 clock-names = "core", "iface";
 622                                 status = "disabled";
 623                         };
 624                 };
 625
 626                 gsbi7: gsbi@16600000 {
 627                         status = "disabled";
 628                         compatible = "qcom,gsbi-v1.0.0";
 629                         cell-index = <7>;
 630                         reg = <0x16600000 0x100>;
 631                         clocks = <&gcc GSBI7_H_CLK>;
 632                         clock-names = "iface";
 633                         #address-cells = <1>;
 634                         #size-cells = <1>;
 635                         ranges;
 636                         syscon-tcsr = <&tcsr>;
 637
 638                         gsbi7_serial: serial@16640000 {
 639                                 compatible = "qcom,msm-uartdm-v1.3", "qcom,msm-uartdm";
 640                                 reg = <0x16640000 0x1000>,
 641                                       <0x16600000 0x1000>;
 642                                 interrupts = <0 158 IRQ_TYPE_LEVEL_HIGH>;
 643                                 clocks = <&gcc GSBI7_UART_CLK>, <&gcc GSBI7_H_CLK>;
 644                                 clock-names = "core", "iface";
 645                                 status = "disabled";
 646                         };
 647
 648                         gsbi7_i2c: i2c@16680000 {
 649                                 compatible = "qcom,i2c-qup-v1.1.1";
 650                                 pinctrl-0 = <&i2c7_pins>;
 651                                 pinctrl-1 = <&i2c7_pins_sleep>;
 652                                 pinctrl-names = "default", "sleep";
 653                                 reg = <0x16680000 0x1000>;
 654                                 interrupts = <GIC_SPI 159 IRQ_TYPE_LEVEL_HIGH>;
 655                                 clocks = <&gcc GSBI7_QUP_CLK>,
 656                                          <&gcc GSBI7_H_CLK>;
 657                                 clock-names = "core", "iface";
 658                                 status = "disabled";
 659                         };
 660                 };
 661
 662                 rng@1a500000 {
 663                         compatible = "qcom,prng";
 664                         reg = <0x1a500000 0x200>;
 665                         clocks = <&gcc PRNG_CLK>;
 666                         clock-names = "core";
 667                 };
 668
 669                 ssbi@c00000 {
 670                         compatible = "qcom,ssbi";
 671                         reg = <0x00c00000 0x1000>;
 672                         qcom,controller-type = "pmic-arbiter";
 673
 674                         pm8821: pmic@1 {
 675                                 compatible = "qcom,pm8821";
 676                                 interrupt-parent = <&tlmm_pinmux>;
 677                                 interrupts = <76 IRQ_TYPE_LEVEL_LOW>;
 678                                 #interrupt-cells = <2>;
 679                                 interrupt-controller;
 680                                 #address-cells = <1>;
 681                                 #size-cells = <0>;
 682
 683                                 pm8821_mpps: mpps@50 {
 684                                         compatible = "qcom,pm8821-mpp", "qcom,ssbi-mpp";
 685                                         reg = <0x50>;
 686                                         interrupt-controller;
 687                                         #interrupt-cells = <2>;
 688                                         gpio-controller;
 689                                         #gpio-cells = <2>;
 690                                         gpio-ranges = <&pm8821_mpps 0 0 4>;
 691                                 };
 692                         };
 693                 };
 694
 695                 qcom,ssbi@500000 {
 696                         compatible = "qcom,ssbi";
 697                         reg = <0x00500000 0x1000>;
 698                         qcom,controller-type = "pmic-arbiter";
 699
 700                         pmicintc: pmic@0 {
 701                                 compatible = "qcom,pm8921";
 702                                 interrupt-parent = <&tlmm_pinmux>;
 703                                 interrupts = <74 8>;
 704                                 #interrupt-cells = <2>;
 705                                 interrupt-controller;
 706                                 #address-cells = <1>;
 707                                 #size-cells = <0>;
 708
 709                                 pm8921_gpio: gpio@150 {
 710
 711                                         compatible = "qcom,pm8921-gpio",
 712                                                      "qcom,ssbi-gpio";
 713                                         reg = <0x150>;
 714                                         interrupt-controller;
 715                                         #interrupt-cells = <2>;
 716                                         gpio-controller;
 717                                         gpio-ranges = <&pm8921_gpio 0 0 44>;
 718                                         #gpio-cells = <2>;
 719
 720                                 };
 721
 722                                 pm8921_mpps: mpps@50 {
 723                                         compatible = "qcom,pm8921-mpp",
 724                                                      "qcom,ssbi-mpp";
 725                                         reg = <0x50>;
 726                                         gpio-controller;
 727                                         #gpio-cells = <2>;
 728                                         gpio-ranges = <&pm8921_mpps 0 0 12>;
 729                                         interrupt-controller;
 730                                         #interrupt-cells = <2>;
 731                                 };
 732
 733                                 rtc@11d {
 734                                         compatible = "qcom,pm8921-rtc";
 735                                         interrupt-parent = <&pmicintc>;
 736                                         interrupts = <39 1>;
 737                                         reg = <0x11d>;
 738                                         allow-set-time;
 739                                 };
 740
 741                                 pwrkey@1c {
 742                                         compatible = "qcom,pm8921-pwrkey";
 743                                         reg = <0x1c>;
 744                                         interrupt-parent = <&pmicintc>;
 745                                         interrupts = <50 1>, <51 1>;
 746                                         debounce = <15625>;
 747                                         pull-up;
 748                                 };
 749
 750                                 xoadc: xoadc@197 {
 751                                         compatible = "qcom,pm8921-adc";
 752                                         reg = <197>;
 753                                         interrupts-extended = <&pmicintc 78 IRQ_TYPE_EDGE_RISING>;
 754                                         #address-cells = <2>;
 755                                         #size-cells = <0>;
 756                                         #io-channel-cells = <2>;
 757
 758                                         vcoin: adc-channel@0 {
 759                                                 reg = <0x00 0x00>;
 760                                         };
 761                                         vbat: adc-channel@1 {
 762                                                 reg = <0x00 0x01>;
 763                                         };
 764                                         dcin: adc-channel@2 {
 765                                                 reg = <0x00 0x02>;
 766                                         };
 767                                         vph_pwr: adc-channel@4 {
 768                                                 reg = <0x00 0x04>;
 769                                         };
 770                                         batt_therm: adc-channel@8 {
 771                                                 reg = <0x00 0x08>;
 772                                         };
 773                                         batt_id: adc-channel@9 {
 774                                                 reg = <0x00 0x09>;
 775                                         };
 776                                         usb_vbus: adc-channel@a {
 777                                                 reg = <0x00 0x0a>;
 778                                         };
 779                                         die_temp: adc-channel@b {
 780                                                 reg = <0x00 0x0b>;
 781                                         };
 782                                         ref_625mv: adc-channel@c {
 783                                                 reg = <0x00 0x0c>;
 784                                         };
 785                                         ref_1250mv: adc-channel@d {
 786                                                 reg = <0x00 0x0d>;
 787                                         };
 788                                         chg_temp: adc-channel@e {
 789                                                 reg = <0x00 0x0e>;
 790                                         };
 791                                         ref_muxoff: adc-channel@f {
 792                                                 reg = <0x00 0x0f>;
 793                                         };
 794                                 };
 795                         };
 796                 };
 797
 798                 qfprom: qfprom@700000 {
 799                         compatible      = "qcom,qfprom";
 800                         reg             = <0x00700000 0x1000>;
 801                         #address-cells  = <1>;
 802                         #size-cells     = <1>;
 803                         ranges;
 804                         tsens_calib: calib {
 805                                 reg = <0x404 0x10>;
 806                         };
 807                         tsens_backup: backup_calib {
 808                                 reg = <0x414 0x10>;
 809                         };
 810                 };
 811
 812                 gcc: clock-controller@900000 {
 813                         compatible = "qcom,gcc-apq8064";
 814                         reg = <0x00900000 0x4000>;
 815                         nvmem-cells = <&tsens_calib>, <&tsens_backup>;
 816                         nvmem-cell-names = "calib", "calib_backup";
 817                         #clock-cells = <1>;
 818                         #power-domain-cells = <1>;
 819                         #reset-cells = <1>;
 820                         #thermal-sensor-cells = <1>;
 821                 };
 822
 823                 lcc: clock-controller@28000000 {
 824                         compatible = "qcom,lcc-apq8064";
 825                         reg = <0x28000000 0x1000>;
 826                         #clock-cells = <1>;
 827                         #reset-cells = <1>;
 828                 };
 829
 830                 mmcc: clock-controller@4000000 {
 831                         compatible = "qcom,mmcc-apq8064";
 832                         reg = <0x4000000 0x1000>;
 833                         #clock-cells = <1>;
 834                         #power-domain-cells = <1>;
 835                         #reset-cells = <1>;
 836                 };
 837
 838                 l2cc: clock-controller@2011000 {
 839                         compatible      = "qcom,kpss-gcc", "syscon";
 840                         reg             = <0x2011000 0x1000>;
 841                 };
 842
 843                 rpm@108000 {
 844                         compatible      = "qcom,rpm-apq8064";
 845                         reg             = <0x108000 0x1000>;
 846                         qcom,ipc        = <&l2cc 0x8 2>;
 847
 848                         interrupts      = <GIC_SPI 19 IRQ_TYPE_EDGE_RISING>,
 849                                           <GIC_SPI 21 IRQ_TYPE_EDGE_RISING>,
 850                                           <GIC_SPI 22 IRQ_TYPE_EDGE_RISING>;
 851                         interrupt-names = "ack", "err", "wakeup";
 852
 853                         rpmcc: clock-controller {
 854                                 compatible      = "qcom,rpmcc-apq8064", "qcom,rpmcc";
 855                                 #clock-cells = <1>;
 856                         };
 857
 858                         regulators {
 859                                 compatible = "qcom,rpm-pm8921-regulators";
 860
 861                                 pm8921_s1: s1 {};
 862                                 pm8921_s2: s2 {};
 863                                 pm8921_s3: s3 {};
 864                                 pm8921_s4: s4 {};
 865                                 pm8921_s7: s7 {};
 866                                 pm8921_s8: s8 {};
 867
 868                                 pm8921_l1: l1 {};
 869                                 pm8921_l2: l2 {};
 870                                 pm8921_l3: l3 {};
 871                                 pm8921_l4: l4 {};
 872                                 pm8921_l5: l5 {};
 873                                 pm8921_l6: l6 {};
 874                                 pm8921_l7: l7 {};
 875                                 pm8921_l8: l8 {};
 876                                 pm8921_l9: l9 {};
 877                                 pm8921_l10: l10 {};
 878                                 pm8921_l11: l11 {};
 879                                 pm8921_l12: l12 {};
 880                                 pm8921_l14: l14 {};
 881                                 pm8921_l15: l15 {};
 882                                 pm8921_l16: l16 {};
 883                                 pm8921_l17: l17 {};
 884                                 pm8921_l18: l18 {};
 885                                 pm8921_l21: l21 {};
 886                                 pm8921_l22: l22 {};
 887                                 pm8921_l23: l23 {};
 888                                 pm8921_l24: l24 {};
 889                                 pm8921_l25: l25 {};
 890                                 pm8921_l26: l26 {};
 891                                 pm8921_l27: l27 {};
 892                                 pm8921_l28: l28 {};
 893                                 pm8921_l29: l29 {};
 894
 895                                 pm8921_lvs1: lvs1 {};
 896                                 pm8921_lvs2: lvs2 {};
 897                                 pm8921_lvs3: lvs3 {};
 898                                 pm8921_lvs4: lvs4 {};
 899                                 pm8921_lvs5: lvs5 {};
 900                                 pm8921_lvs6: lvs6 {};
 901                                 pm8921_lvs7: lvs7 {};
 902
 903                                 pm8921_usb_switch: usb-switch {};
 904
 905                                 pm8921_hdmi_switch: hdmi-switch {
 906                                         bias-pull-down;
 907                                 };
 908
 909                                 pm8921_ncp: ncp {};
 910                         };
 911                 };
 912
 913                 usb1: usb@12500000 {
 914                         compatible = "qcom,ci-hdrc";
 915                         reg = <0x12500000 0x200>,
 916                               <0x12500200 0x200>;
 917                         interrupts = <GIC_SPI 100 IRQ_TYPE_LEVEL_HIGH>;
 918                         clocks = <&gcc USB_HS1_XCVR_CLK>, <&gcc USB_HS1_H_CLK>;
 919                         clock-names = "core", "iface";
 920                         assigned-clocks = <&gcc USB_HS1_XCVR_CLK>;
 921                         assigned-clock-rates = <60000000>;
 922                         resets = <&gcc USB_HS1_RESET>;
 923                         reset-names = "core";
 924                         phy_type = "ulpi";
 925                         ahb-burst-config = <0>;
 926                         phys = <&usb_hs1_phy>;
 927                         phy-names = "usb-phy";
 928                         status = "disabled";
 929                         #reset-cells = <1>;
 930
 931                         ulpi {
 932                                 usb_hs1_phy: phy {
 933                                         compatible = "qcom,usb-hs-phy-apq8064",
 934                                                      "qcom,usb-hs-phy";
 935                                         clocks = <&sleep_clk>, <&cxo_board>;
 936                                         clock-names = "sleep", "ref";
 937                                         resets = <&usb1 0>;
 938                                         reset-names = "por";
 939                                         #phy-cells = <0>;
 940                                 };
 941                         };
 942                 };
 943
 944                 usb3: usb@12520000 {
 945                         compatible = "qcom,ci-hdrc";
 946                         reg = <0x12520000 0x200>,
 947                               <0x12520200 0x200>;
 948                         interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH>;
 949                         clocks = <&gcc USB_HS3_XCVR_CLK>, <&gcc USB_HS3_H_CLK>;
 950                         clock-names = "core", "iface";
 951                         assigned-clocks = <&gcc USB_HS3_XCVR_CLK>;
 952                         assigned-clock-rates = <60000000>;
 953                         resets = <&gcc USB_HS3_RESET>;
 954                         reset-names = "core";
 955                         phy_type = "ulpi";
 956                         ahb-burst-config = <0>;
 957                         phys = <&usb_hs3_phy>;
 958                         phy-names = "usb-phy";
 959                         status = "disabled";
 960                         #reset-cells = <1>;
 961
 962                         ulpi {
 963                                 usb_hs3_phy: phy {
 964                                         compatible = "qcom,usb-hs-phy-apq8064",
 965                                                      "qcom,usb-hs-phy";
 966                                         #phy-cells = <0>;
 967                                         clocks = <&sleep_clk>, <&cxo_board>;
 968                                         clock-names = "sleep", "ref";
 969                                         resets = <&usb3 0>;
 970                                         reset-names = "por";
 971                                 };
 972                         };
 973                 };
 974
 975                 usb4: usb@12530000 {
 976                         compatible = "qcom,ci-hdrc";
 977                         reg = <0x12530000 0x200>,
 978                               <0x12530200 0x200>;
 979                         interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
 980                         clocks = <&gcc USB_HS4_XCVR_CLK>, <&gcc USB_HS4_H_CLK>;
 981                         clock-names = "core", "iface";
 982                         assigned-clocks = <&gcc USB_HS4_XCVR_CLK>;
 983                         assigned-clock-rates = <60000000>;
 984                         resets = <&gcc USB_HS4_RESET>;
 985                         reset-names = "core";
 986                         phy_type = "ulpi";
 987                         ahb-burst-config = <0>;
 988                         phys = <&usb_hs4_phy>;
 989                         phy-names = "usb-phy";
 990                         status = "disabled";
 991                         #reset-cells = <1>;
 992
 993                         ulpi {
 994                                 usb_hs4_phy: phy {
 995                                         compatible = "qcom,usb-hs-phy-apq8064",
 996                                                      "qcom,usb-hs-phy";
 997                                         #phy-cells = <0>;
 998                                         clocks = <&sleep_clk>, <&cxo_board>;
 999                                         clock-names = "sleep", "ref";
1000                                         resets = <&usb4 0>;
1001                                         reset-names = "por";
1002                                 };
1003                         };
1004                 };
1005
1006                 sata_phy0: phy@1b400000 {
1007                         compatible      = "qcom,apq8064-sata-phy";
1008                         status          = "disabled";
1009                         reg             = <0x1b400000 0x200>;
1010                         reg-names       = "phy_mem";
1011                         clocks          = <&gcc SATA_PHY_CFG_CLK>;
1012                         clock-names     = "cfg";
1013                         #phy-cells      = <0>;
1014                 };
1015
1016                 sata0: sata@29000000 {
1017                         compatible              = "qcom,apq8064-ahci", "generic-ahci";
1018                         status                  = "disabled";
1019                         reg                     = <0x29000000 0x180>;
1020                         interrupts              = <GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH>;
1021
1022                         clocks                  = <&gcc SFAB_SATA_S_H_CLK>,
1023                                                 <&gcc SATA_H_CLK>,
1024                                                 <&gcc SATA_A_CLK>,
1025                                                 <&gcc SATA_RXOOB_CLK>,
1026                                                 <&gcc SATA_PMALIVE_CLK>;
1027                         clock-names             = "slave_iface",
1028                                                 "iface",
1029                                                 "bus",
1030                                                 "rxoob",
1031                                                 "core_pmalive";
1032
1033                         assigned-clocks         = <&gcc SATA_RXOOB_CLK>,
1034                                                 <&gcc SATA_PMALIVE_CLK>;
1035                         assigned-clock-rates    = <100000000>, <100000000>;
1036
1037                         phys                    = <&sata_phy0>;
1038                         phy-names               = "sata-phy";
1039                         ports-implemented       = <0x1>;
1040                 };
1041
1042                 /* Temporary fixed regulator */
1043                 sdcc1bam: dma-controller@12402000{
1044                         compatible = "qcom,bam-v1.3.0";
1045                         reg = <0x12402000 0x8000>;
1046                         interrupts = <0 98 IRQ_TYPE_LEVEL_HIGH>;
1047                         clocks = <&gcc SDC1_H_CLK>;
1048                         clock-names = "bam_clk";
1049                         #dma-cells = <1>;
1050                         qcom,ee = <0>;
1051                 };
1052
1053                 sdcc3bam: dma-controller@12182000{
1054                         compatible = "qcom,bam-v1.3.0";
1055                         reg = <0x12182000 0x8000>;
1056                         interrupts = <0 96 IRQ_TYPE_LEVEL_HIGH>;
1057                         clocks = <&gcc SDC3_H_CLK>;
1058                         clock-names = "bam_clk";
1059                         #dma-cells = <1>;
1060                         qcom,ee = <0>;
1061                 };
1062
1063                 sdcc4bam: dma-controller@121c2000{
1064                         compatible = "qcom,bam-v1.3.0";
1065                         reg = <0x121c2000 0x8000>;
1066                         interrupts = <0 95 IRQ_TYPE_LEVEL_HIGH>;
1067                         clocks = <&gcc SDC4_H_CLK>;
1068                         clock-names = "bam_clk";
1069                         #dma-cells = <1>;
1070                         qcom,ee = <0>;
1071                 };
1072
1073                 amba {
1074                         compatible = "simple-bus";
1075                         #address-cells = <1>;
1076                         #size-cells = <1>;
1077                         ranges;
1078                         sdcc1: mmc@12400000 {
1079                                 status          = "disabled";
1080                                 compatible      = "arm,pl18x", "arm,primecell";
1081                                 pinctrl-names   = "default";
1082                                 pinctrl-0       = <&sdcc1_pins>;
1083                                 arm,primecell-periphid = <0x00051180>;
1084                                 reg             = <0x12400000 0x2000>;
1085                                 interrupts      = <GIC_SPI 104 IRQ_TYPE_LEVEL_HIGH>;
1086                                 interrupt-names = "cmd_irq";
1087                                 clocks          = <&gcc SDC1_CLK>, <&gcc SDC1_H_CLK>;
1088                                 clock-names     = "mclk", "apb_pclk";
1089                                 bus-width       = <8>;
1090                                 max-frequency   = <96000000>;
1091                                 non-removable;
1092                                 cap-sd-highspeed;
1093                                 cap-mmc-highspeed;
1094                                 dmas = <&sdcc1bam 2>, <&sdcc1bam 1>;
1095                                 dma-names = "tx", "rx";
1096                         };
1097
1098                         sdcc3: mmc@12180000 {
1099                                 compatible      = "arm,pl18x", "arm,primecell";
1100                                 arm,primecell-periphid = <0x00051180>;
1101                                 status          = "disabled";
1102                                 reg             = <0x12180000 0x2000>;
1103                                 interrupts      = <GIC_SPI 102 IRQ_TYPE_LEVEL_HIGH>;
1104                                 interrupt-names = "cmd_irq";
1105                                 clocks          = <&gcc SDC3_CLK>, <&gcc SDC3_H_CLK>;
1106                                 clock-names     = "mclk", "apb_pclk";
1107                                 bus-width       = <4>;
1108                                 cap-sd-highspeed;
1109                                 cap-mmc-highspeed;
1110                                 max-frequency   = <192000000>;
1111                                 no-1-8-v;
1112                                 dmas = <&sdcc3bam 2>, <&sdcc3bam 1>;
1113                                 dma-names = "tx", "rx";
1114                         };
1115
1116                         sdcc4: mmc@121c0000 {
1117                                 compatible      = "arm,pl18x", "arm,primecell";
1118                                 arm,primecell-periphid = <0x00051180>;
1119                                 status          = "disabled";
1120                                 reg             = <0x121c0000 0x2000>;
1121                                 interrupts      = <GIC_SPI 101 IRQ_TYPE_LEVEL_HIGH>;
1122                                 interrupt-names = "cmd_irq";
1123                                 clocks          = <&gcc SDC4_CLK>, <&gcc SDC4_H_CLK>;
1124                                 clock-names     = "mclk", "apb_pclk";
1125                                 bus-width       = <4>;
1126                                 cap-sd-highspeed;
1127                                 cap-mmc-highspeed;
1128                                 max-frequency   = <48000000>;
1129                                 dmas = <&sdcc4bam 2>, <&sdcc4bam 1>;
1130                                 dma-names = "tx", "rx";
1131                                 pinctrl-names = "default";
1132                                 pinctrl-0 = <&sdc4_gpios>;
1133                         };
1134                 };
1135
1136                 tcsr: syscon@1a400000 {
1137                         compatible = "qcom,tcsr-apq8064", "syscon";
1138                         reg = <0x1a400000 0x100>;
1139                 };
1140
1141                 gpu: adreno-3xx@4300000 {
1142                         compatible = "qcom,adreno-320.2", "qcom,adreno";
1143                         reg = <0x04300000 0x20000>;
1144                         reg-names = "kgsl_3d0_reg_memory";
1145                         interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>;
1146                         interrupt-names = "kgsl_3d0_irq";
1147                         clock-names =
1148                             "core",
1149                             "iface",
1150                             "mem",
1151                             "mem_iface";
1152                         clocks =
1153                             <&mmcc GFX3D_CLK>,
1154                             <&mmcc GFX3D_AHB_CLK>,
1155                             <&mmcc GFX3D_AXI_CLK>,
1156                             <&mmcc MMSS_IMEM_AHB_CLK>;
1157
1158                         iommus = <&gfx3d 0
1159                                   &gfx3d 1
1160                                   &gfx3d 2
1161                                   &gfx3d 3
1162                                   &gfx3d 4
1163                                   &gfx3d 5
1164                                   &gfx3d 6
1165                                   &gfx3d 7
1166                                   &gfx3d 8
1167                                   &gfx3d 9
1168                                   &gfx3d 10
1169                                   &gfx3d 11
1170                                   &gfx3d 12
1171                                   &gfx3d 13
1172                                   &gfx3d 14
1173                                   &gfx3d 15
1174                                   &gfx3d 16
1175                                   &gfx3d 17
1176                                   &gfx3d 18
1177                                   &gfx3d 19
1178                                   &gfx3d 20
1179                                   &gfx3d 21
1180                                   &gfx3d 22
1181                                   &gfx3d 23
1182                                   &gfx3d 24
1183                                   &gfx3d 25
1184                                   &gfx3d 26
1185                                   &gfx3d 27
1186                                   &gfx3d 28
1187                                   &gfx3d 29
1188                                   &gfx3d 30
1189                                   &gfx3d 31
1190                                   &gfx3d1 0
1191                                   &gfx3d1 1
1192                                   &gfx3d1 2
1193                                   &gfx3d1 3
1194                                   &gfx3d1 4
1195                                   &gfx3d1 5
1196                                   &gfx3d1 6
1197                                   &gfx3d1 7
1198                                   &gfx3d1 8
1199                                   &gfx3d1 9
1200                                   &gfx3d1 10
1201                                   &gfx3d1 11
1202                                   &gfx3d1 12
1203                                   &gfx3d1 13
1204                                   &gfx3d1 14
1205                                   &gfx3d1 15
1206                                   &gfx3d1 16
1207                                   &gfx3d1 17
1208                                   &gfx3d1 18
1209                                   &gfx3d1 19
1210                                   &gfx3d1 20
1211                                   &gfx3d1 21
1212                                   &gfx3d1 22
1213                                   &gfx3d1 23
1214                                   &gfx3d1 24
1215                                   &gfx3d1 25
1216                                   &gfx3d1 26
1217                                   &gfx3d1 27
1218                                   &gfx3d1 28
1219                                   &gfx3d1 29
1220                                   &gfx3d1 30
1221                                   &gfx3d1 31>;
1222
1223                         operating-points-v2 = <&gpu_opp_table>;
1224
1225                         gpu_opp_table: opp-table {
1226                                 compatible = "operating-points-v2";
1227
1228                                 opp-320000000 {
1229                                         opp-hz = /bits/ 64 <450000000>;
1230                                 };
1231
1232                                 opp-27000000 {
1233                                         opp-hz = /bits/ 64 <27000000>;
1234                                 };
1235                         };
1236                 };
1237
1238                 mmss_sfpb: syscon@5700000 {
1239                         compatible = "syscon";
1240                         reg = <0x5700000 0x70>;
1241                 };
1242
1243                 dsi0: dsi@4700000 {
1244                         compatible = "qcom,mdss-dsi-ctrl";
1245                         label = "MDSS DSI CTRL->0";
1246                         #address-cells = <1>;
1247                         #size-cells = <0>;
1248                         interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
1249                         reg = <0x04700000 0x200>;
1250                         reg-names = "dsi_ctrl";
1251
1252                         clocks = <&mmcc DSI_M_AHB_CLK>,
1253                                 <&mmcc DSI_S_AHB_CLK>,
1254                                 <&mmcc AMP_AHB_CLK>,
1255                                 <&mmcc DSI_CLK>,
1256                                 <&mmcc DSI1_BYTE_CLK>,
1257                                 <&mmcc DSI_PIXEL_CLK>,
1258                                 <&mmcc DSI1_ESC_CLK>;
1259                         clock-names = "iface", "bus", "core_mmss",
1260                                         "src", "byte", "pixel",
1261                                         "core";
1262
1263                         assigned-clocks = <&mmcc DSI1_BYTE_SRC>,
1264                                         <&mmcc DSI1_ESC_SRC>,
1265                                         <&mmcc DSI_SRC>,
1266                                         <&mmcc DSI_PIXEL_SRC>;
1267                         assigned-clock-parents = <&dsi0_phy 0>,
1268                                                 <&dsi0_phy 0>,
1269                                                 <&dsi0_phy 1>,
1270                                                 <&dsi0_phy 1>;
1271                         syscon-sfpb = <&mmss_sfpb>;
1272                         phys = <&dsi0_phy>;
1273                         phy-names = "dsi";
1274                         ports {
1275                                 #address-cells = <1>;
1276                                 #size-cells = <0>;
1277
1278                                 port@0 {
1279                                         reg = <0>;
1280                                         dsi0_in: endpoint {
1281                                         };
1282                                 };
1283
1284                                 port@1 {
1285                                         reg = <1>;
1286                                         dsi0_out: endpoint {
1287                                         };
1288                                 };
1289                         };
1290                 };
1291
1292
1293                 dsi0_phy: dsi-phy@4700200 {
1294                         compatible = "qcom,dsi-phy-28nm-8960";
1295                         #clock-cells = <1>;
1296                         #phy-cells = <0>;
1297
1298                         reg = <0x04700200 0x100>,
1299                                 <0x04700300 0x200>,
1300                                 <0x04700500 0x5c>;
1301                         reg-names = "dsi_pll", "dsi_phy", "dsi_phy_regulator";
1302                         clock-names = "iface_clk", "ref";
1303                         clocks = <&mmcc DSI_M_AHB_CLK>,
1304                                  <&pxo_board>;
1305                 };
1306
1307
1308                 mdp_port0: iommu@7500000 {
1309                         compatible = "qcom,apq8064-iommu";
1310                         #iommu-cells = <1>;
1311                         clock-names =
1312                             "smmu_pclk",
1313                             "iommu_clk";
1314                         clocks =
1315                             <&mmcc SMMU_AHB_CLK>,
1316                             <&mmcc MDP_AXI_CLK>;
1317                         reg = <0x07500000 0x100000>;
1318                         interrupts =
1319                             <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>,
1320                             <GIC_SPI 64 IRQ_TYPE_LEVEL_HIGH>;
1321                         qcom,ncb = <2>;
1322                 };
1323
1324                 mdp_port1: iommu@7600000 {
1325                         compatible = "qcom,apq8064-iommu";
1326                         #iommu-cells = <1>;
1327                         clock-names =
1328                             "smmu_pclk",
1329                             "iommu_clk";
1330                         clocks =
1331                             <&mmcc SMMU_AHB_CLK>,
1332                             <&mmcc MDP_AXI_CLK>;
1333                         reg = <0x07600000 0x100000>;
1334                         interrupts =
1335                             <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>,
1336                             <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
1337                         qcom,ncb = <2>;
1338                 };
1339
1340                 gfx3d: iommu@7c00000 {
1341                         compatible = "qcom,apq8064-iommu";
1342                         #iommu-cells = <1>;
1343                         clock-names =
1344                             "smmu_pclk",
1345                             "iommu_clk";
1346                         clocks =
1347                             <&mmcc SMMU_AHB_CLK>,
1348                             <&mmcc GFX3D_AXI_CLK>;
1349                         reg = <0x07c00000 0x100000>;
1350                         interrupts =
1351                             <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH>,
1352                             <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>;
1353                         qcom,ncb = <3>;
1354                 };
1355
1356                 gfx3d1: iommu@7d00000 {
1357                         compatible = "qcom,apq8064-iommu";
1358                         #iommu-cells = <1>;
1359                         clock-names =
1360                             "smmu_pclk",
1361                             "iommu_clk";
1362                         clocks =
1363                             <&mmcc SMMU_AHB_CLK>,
1364                             <&mmcc GFX3D_AXI_CLK>;
1365                         reg = <0x07d00000 0x100000>;
1366                         interrupts =
1367                             <GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH>,
1368                             <GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH>;
1369                         qcom,ncb = <3>;
1370                 };
1371
1372                 pcie: pci@1b500000 {
1373                         compatible = "qcom,pcie-apq8064", "snps,dw-pcie";
1374                         reg = <0x1b500000 0x1000>,
1375                               <0x1b502000 0x80>,
1376                               <0x1b600000 0x100>,
1377                               <0x0ff00000 0x100000>;
1378                         reg-names = "dbi", "elbi", "parf", "config";
1379                         device_type = "pci";
1380                         linux,pci-domain = <0>;
1381                         bus-range = <0x00 0xff>;
1382                         num-lanes = <1>;
1383                         #address-cells = <3>;
1384                         #size-cells = <2>;
1385                         ranges = <0x81000000 0 0          0x0fe00000 0 0x00100000>, /* I/O */
1386                                  <0x82000000 0 0x08000000 0x08000000 0 0x07e00000>; /* mem */
1387                         interrupts = <GIC_SPI 238 IRQ_TYPE_LEVEL_HIGH>;
1388                         interrupt-names = "msi";
1389                         #interrupt-cells = <1>;
1390                         interrupt-map-mask = <0 0 0 0x7>;
1391                         interrupt-map = <0 0 0 1 &intc 0 36 IRQ_TYPE_LEVEL_HIGH>, /* int_a */
1392                                         <0 0 0 2 &intc 0 37 IRQ_TYPE_LEVEL_HIGH>, /* int_b */
1393                                         <0 0 0 3 &intc 0 38 IRQ_TYPE_LEVEL_HIGH>, /* int_c */
1394                                         <0 0 0 4 &intc 0 39 IRQ_TYPE_LEVEL_HIGH>; /* int_d */
1395                         clocks = <&gcc PCIE_A_CLK>,
1396                                  <&gcc PCIE_H_CLK>,
1397                                  <&gcc PCIE_PHY_REF_CLK>;
1398                         clock-names = "core", "iface", "phy";
1399                         resets = <&gcc PCIE_ACLK_RESET>,
1400                                  <&gcc PCIE_HCLK_RESET>,
1401                                  <&gcc PCIE_POR_RESET>,
1402                                  <&gcc PCIE_PCI_RESET>,
1403                                  <&gcc PCIE_PHY_RESET>;
1404                         reset-names = "axi", "ahb", "por", "pci", "phy";
1405                         status = "disabled";
1406                 };
1407
1408                 hdmi: hdmi-tx@4a00000 {
1409                         compatible = "qcom,hdmi-tx-8960";
1410                         pinctrl-names = "default";
1411                         pinctrl-0 = <&hdmi_pinctrl>;
1412                         reg = <0x04a00000 0x2f0>;
1413                         reg-names = "core_physical";
1414                         interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
1415                         clocks = <&mmcc HDMI_APP_CLK>,
1416                                  <&mmcc HDMI_M_AHB_CLK>,
1417                                  <&mmcc HDMI_S_AHB_CLK>;
1418                         clock-names = "core",
1419                                       "master_iface",
1420                                       "slave_iface";
1421
1422                         phys = <&hdmi_phy>;
1423                         phy-names = "hdmi-phy";
1424
1425                         ports {
1426                                 #address-cells = <1>;
1427                                 #size-cells = <0>;
1428
1429                                 port@0 {
1430                                         reg = <0>;
1431                                         hdmi_in: endpoint {
1432                                         };
1433                                 };
1434
1435                                 port@1 {
1436                                         reg = <1>;
1437                                         hdmi_out: endpoint {
1438                                         };
1439                                 };
1440                         };
1441                 };
1442
1443                 hdmi_phy: hdmi-phy@4a00400 {
1444                         compatible = "qcom,hdmi-phy-8960";
1445                         reg = <0x4a00400 0x60>,
1446                               <0x4a00500 0x100>;
1447                         reg-names = "hdmi_phy",
1448                                     "hdmi_pll";
1449
1450                         clocks = <&mmcc HDMI_S_AHB_CLK>;
1451                         clock-names = "slave_iface";
1452                         #phy-cells = <0>;
1453                 };
1454
1455                 mdp: mdp@5100000 {
1456                         compatible = "qcom,mdp4";
1457                         reg = <0x05100000 0xf0000>;
1458                         interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
1459                         clocks = <&mmcc MDP_CLK>,
1460                                  <&mmcc MDP_AHB_CLK>,
1461                                  <&mmcc MDP_AXI_CLK>,
1462                                  <&mmcc MDP_LUT_CLK>,
1463                                  <&mmcc HDMI_TV_CLK>,
1464                                  <&mmcc MDP_TV_CLK>;
1465                         clock-names = "core_clk",
1466                                       "iface_clk",
1467                                       "bus_clk",
1468                                       "lut_clk",
1469                                       "hdmi_clk",
1470                                       "tv_clk";
1471
1472                         iommus = <&mdp_port0 0
1473                                   &mdp_port0 2
1474                                   &mdp_port1 0
1475                                   &mdp_port1 2>;
1476
1477                         ports {
1478                                 #address-cells = <1>;
1479                                 #size-cells = <0>;
1480
1481                                 port@0 {
1482                                         reg = <0>;
1483                                         mdp_lvds_out: endpoint {
1484                                         };
1485                                 };
1486
1487                                 port@1 {
1488                                         reg = <1>;
1489                                         mdp_dsi1_out: endpoint {
1490                                         };
1491                                 };
1492
1493                                 port@2 {
1494                                         reg = <2>;
1495                                         mdp_dsi2_out: endpoint {
1496                                         };
1497                                 };
1498
1499                                 port@3 {
1500                                         reg = <3>;
1501                                         mdp_dtv_out: endpoint {
1502                                         };
1503                                 };
1504                         };
1505                 };
1506
1507                 riva: riva-pil@3204000 {
1508                         compatible = "qcom,riva-pil";
1509
1510                         reg = <0x03200800 0x1000>, <0x03202000 0x2000>, <0x03204000 0x100>;
1511                         reg-names = "ccu", "dxe", "pmu";
1512
1513                         interrupts-extended = <&intc GIC_SPI 199 IRQ_TYPE_EDGE_RISING>,
1514                                               <&wcnss_smsm 6 IRQ_TYPE_EDGE_RISING>;
1515                         interrupt-names = "wdog", "fatal";
1516
1517                         memory-region = <&wcnss_mem>;
1518
1519                         vddcx-supply = <&pm8921_s3>;
1520                         vddmx-supply = <&pm8921_l24>;
1521                         vddpx-supply = <&pm8921_s4>;
1522
1523                         status = "disabled";
1524
1525                         iris {
1526                                 compatible = "qcom,wcn3660";
1527
1528                                 clocks = <&cxo_board>;
1529                                 clock-names = "xo";
1530
1531                                 vddxo-supply = <&pm8921_l4>;
1532                                 vddrfa-supply = <&pm8921_s2>;
1533                                 vddpa-supply = <&pm8921_l10>;
1534                                 vdddig-supply = <&pm8921_lvs2>;
1535                         };
1536
1537                         smd-edge {
1538                                 interrupts = <GIC_SPI 198 IRQ_TYPE_EDGE_RISING>;
1539
1540                                 qcom,ipc = <&l2cc 8 25>;
1541                                 qcom,smd-edge = <6>;
1542
1543                                 label = "riva";
1544
1545                                 wcnss {
1546                                         compatible = "qcom,wcnss";
1547                                         qcom,smd-channels = "WCNSS_CTRL";
1548
1549                                         qcom,mmio = <&riva>;
1550
1551                                         bluetooth {
1552                                                 compatible = "qcom,wcnss-bt";
1553                                         };
1554
1555                                         wifi {
1556                                                 compatible = "qcom,wcnss-wlan";
1557
1558                                                 interrupts = <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH>,
1559                                                              <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH>;
1560                                                 interrupt-names = "tx", "rx";
1561
1562                                                 qcom,smem-states = <&apps_smsm 10>, <&apps_smsm 9>;
1563                                                 qcom,smem-state-names = "tx-enable", "tx-rings-empty";
1564                                         };
1565                                 };
1566                         };
1567                 };
1568
1569                 etb@1a01000 {
1570                         compatible = "coresight-etb10", "arm,primecell";
1571                         reg = <0x1a01000 0x1000>;
1572
1573                         clocks = <&rpmcc RPM_QDSS_CLK>;
1574                         clock-names = "apb_pclk";
1575
1576                         in-ports {
1577                                 port {
1578                                         etb_in: endpoint {
1579                                                 remote-endpoint = <&replicator_out0>;
1580                                         };
1581                                 };
1582                         };
1583                 };
1584
1585                 tpiu@1a03000 {
1586                         compatible = "arm,coresight-tpiu", "arm,primecell";
1587                         reg = <0x1a03000 0x1000>;
1588
1589                         clocks = <&rpmcc RPM_QDSS_CLK>;
1590                         clock-names = "apb_pclk";
1591
1592                         in-ports {
1593                                 port {
1594                                         tpiu_in: endpoint {
1595                                                 remote-endpoint = <&replicator_out1>;
1596                                         };
1597                                 };
1598                         };
1599                 };
1600
1601                 replicator {
1602                         compatible = "arm,coresight-static-replicator";
1603
1604                         clocks = <&rpmcc RPM_QDSS_CLK>;
1605                         clock-names = "apb_pclk";
1606
1607                         out-ports {
1608                                 #address-cells = <1>;
1609                                 #size-cells = <0>;
1610
1611                                 port@0 {
1612                                         reg = <0>;
1613                                         replicator_out0: endpoint {
1614                                                 remote-endpoint = <&etb_in>;
1615                                         };
1616                                 };
1617                                 port@1 {
1618                                         reg = <1>;
1619                                         replicator_out1: endpoint {
1620                                                 remote-endpoint = <&tpiu_in>;
1621                                         };
1622                                 };
1623                         };
1624
1625                         in-ports {
1626                                 port {
1627                                         replicator_in: endpoint {
1628                                                 remote-endpoint = <&funnel_out>;
1629                                         };
1630                                 };
1631                         };
1632                 };
1633
1634                 funnel@1a04000 {
1635                         compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
1636                         reg = <0x1a04000 0x1000>;
1637
1638                         clocks = <&rpmcc RPM_QDSS_CLK>;
1639                         clock-names = "apb_pclk";
1640
1641                         in-ports {
1642                                 #address-cells = <1>;
1643                                 #size-cells = <0>;
1644
1645                                 /*
1646                                  * Not described input ports:
1647                                  * 2 - connected to STM component
1648                                  * 3 - not-connected
1649                                  * 6 - not-connected
1650                                  * 7 - not-connected
1651                                  */
1652                                 port@0 {
1653                                         reg = <0>;
1654                                         funnel_in0: endpoint {
1655                                                 remote-endpoint = <&etm0_out>;
1656                                         };
1657                                 };
1658                                 port@1 {
1659                                         reg = <1>;
1660                                         funnel_in1: endpoint {
1661                                                 remote-endpoint = <&etm1_out>;
1662                                         };
1663                                 };
1664                                 port@4 {
1665                                         reg = <4>;
1666                                         funnel_in4: endpoint {
1667                                                 remote-endpoint = <&etm2_out>;
1668                                         };
1669                                 };
1670                                 port@5 {
1671                                         reg = <5>;
1672                                         funnel_in5: endpoint {
1673                                                 remote-endpoint = <&etm3_out>;
1674                                         };
1675                                 };
1676                         };
1677
1678                         out-ports {
1679                                 port {
1680                                         funnel_out: endpoint {
1681                                                 remote-endpoint = <&replicator_in>;
1682                                         };
1683                                 };
1684                         };
1685                 };
1686
1687                 etm@1a1c000 {
1688                         compatible = "arm,coresight-etm3x", "arm,primecell";
1689                         reg = <0x1a1c000 0x1000>;
1690
1691                         clocks = <&rpmcc RPM_QDSS_CLK>;
1692                         clock-names = "apb_pclk";
1693
1694                         cpu = <&CPU0>;
1695
1696                         out-ports {
1697                                 port {
1698                                         etm0_out: endpoint {
1699                                                 remote-endpoint = <&funnel_in0>;
1700                                         };
1701                                 };
1702                         };
1703                 };
1704
1705                 etm@1a1d000 {
1706                         compatible = "arm,coresight-etm3x", "arm,primecell";
1707                         reg = <0x1a1d000 0x1000>;
1708
1709                         clocks = <&rpmcc RPM_QDSS_CLK>;
1710                         clock-names = "apb_pclk";
1711
1712                         cpu = <&CPU1>;
1713
1714                         out-ports {
1715                                 port {
1716                                         etm1_out: endpoint {
1717                                                 remote-endpoint = <&funnel_in1>;
1718                                         };
1719                                 };
1720                         };
1721                 };
1722
1723                 etm@1a1e000 {
1724                         compatible = "arm,coresight-etm3x", "arm,primecell";
1725                         reg = <0x1a1e000 0x1000>;
1726
1727                         clocks = <&rpmcc RPM_QDSS_CLK>;
1728                         clock-names = "apb_pclk";
1729
1730                         cpu = <&CPU2>;
1731
1732                         out-ports {
1733                                 port {
1734                                         etm2_out: endpoint {
1735                                                 remote-endpoint = <&funnel_in4>;
1736                                         };
1737                                 };
1738                         };
1739                 };
1740
1741                 etm@1a1f000 {
1742                         compatible = "arm,coresight-etm3x", "arm,primecell";
1743                         reg = <0x1a1f000 0x1000>;
1744
1745                         clocks = <&rpmcc RPM_QDSS_CLK>;
1746                         clock-names = "apb_pclk";
1747
1748                         cpu = <&CPU3>;
1749
1750                         out-ports {
1751                                 port {
1752                                         etm3_out: endpoint {
1753                                                 remote-endpoint = <&funnel_in5>;
1754                                         };
1755                                 };
1756                         };
1757                 };
1758         };
1759 };
1760 #include "qcom-apq8064-pins.dtsi"