1 // SPDX-License-Identifier: GPL-2.0-or-later
3 * Copyright (C) 2013 Pavel Machek <pavel@ucw.cz>
4 * Copyright (C) 2013-2014 Aaro Koskinen <aaro.koskinen@iki.fi>
9 #include "omap34xx.dtsi"
10 #include <dt-bindings/input/input.h>
11 #include <dt-bindings/leds/common.h>
14 * Default secure signed bootloader (Nokia X-Loader) does not enable L3 firewall
15 * for omap AES HW crypto support. When linux kernel try to access memory of AES
16 * blocks then kernel receive "Unhandled fault: external abort on non-linefetch"
17 * and crash. Until somebody fix omap-aes.c and omap_hwmod_3xxx_data.c code (no
18 * crash anymore) omap AES support will be disabled for all Nokia N900 devices.
19 * There is "unofficial" version of bootloader which enables AES in L3 firewall
20 * but it is not widely used and to prevent kernel crash rather AES is disabled.
21 * There is also no runtime detection code if AES is disabled in L3 firewall...
33 compatible = "nokia,omap3-n900", "ti,omap3430", "ti,omap3";
51 compatible = "gpio-leds";
53 label = "debug::sleep";
54 gpios = <&gpio6 2 GPIO_ACTIVE_HIGH>; /* 162 */
55 linux,default-trigger = "default-on";
56 pinctrl-names = "default";
57 pinctrl-0 = <&debug_leds>;
62 device_type = "memory";
63 reg = <0x80000000 0x10000000>; /* 256 MB */
67 compatible = "gpio-keys";
70 label = "Camera Lens Cover";
71 gpios = <&gpio4 14 GPIO_ACTIVE_LOW>; /* 110 */
72 linux,input-type = <EV_SW>;
73 linux,code = <SW_CAMERA_LENS_COVER>;
78 label = "Camera Focus";
79 gpios = <&gpio3 4 GPIO_ACTIVE_LOW>; /* 68 */
80 linux,code = <KEY_CAMERA_FOCUS>;
85 label = "Camera Capture";
86 gpios = <&gpio3 5 GPIO_ACTIVE_LOW>; /* 69 */
87 linux,code = <KEY_CAMERA>;
92 label = "Lock Button";
93 gpios = <&gpio4 17 GPIO_ACTIVE_LOW>; /* 113 */
94 linux,code = <KEY_SCREENLOCK>;
99 label = "Keypad Slide";
100 gpios = <&gpio3 7 GPIO_ACTIVE_LOW>; /* 71 */
101 linux,input-type = <EV_SW>;
102 linux,code = <SW_KEYPAD_SLIDE>;
107 label = "Proximity Sensor";
108 gpios = <&gpio3 25 GPIO_ACTIVE_HIGH>; /* 89 */
109 linux,input-type = <EV_SW>;
110 linux,code = <SW_FRONT_PROXIMITY>;
115 label = "Machine Cover";
116 gpios = <&gpio6 0 GPIO_ACTIVE_LOW>; /* 160 */
117 linux,input-type = <EV_SW>;
118 linux,code = <SW_MACHINE_COVER>;
124 compatible = "nxp,isp1707";
125 nxp,enable-gpio = <&gpio3 3 GPIO_ACTIVE_HIGH>;
126 usb-phy = <&usb2_phy>;
130 compatible = "composite-video-connector";
134 tv_connector_in: endpoint {
135 remote-endpoint = <&venc_out>;
141 compatible = "nokia,n900-audio";
143 nokia,cpu-dai = <&mcbsp2>;
144 nokia,audio-codec = <&tlv320aic3x>, <&tlv320aic3x_aux>;
145 nokia,headphone-amplifier = <&tpa6130a2>;
147 tvout-selection-gpios = <&gpio2 8 GPIO_ACTIVE_HIGH>; /* 40 */
148 jack-detection-gpios = <&gpio6 17 GPIO_ACTIVE_HIGH>; /* 177 */
149 eci-switch-gpios = <&gpio6 22 GPIO_ACTIVE_HIGH>; /* 182 */
150 speaker-amplifier-gpios = <&twl_gpio 7 GPIO_ACTIVE_HIGH>;
153 battery: n900-battery {
154 compatible = "nokia,n900-battery";
155 io-channels = <&twl_madc 0>, <&twl_madc 4>, <&twl_madc 12>;
156 io-channel-names = "temp", "bsi", "vbat";
160 compatible = "ti,omap-dmtimer-pwm";
162 ti,timers = <&timer9>;
163 ti,clock-source = <0x00>; /* timer_sys_ck */
167 compatible = "nokia,n900-ir";
168 pwms = <&pwm9 0 26316 0>; /* 38000 Hz */
172 compatible = "nokia,n900-rom-rng";
177 /* controlled (enabled/disabled) directly by bcm2048 and wl1251 */
179 compatible = "fixed-clock";
181 clock-frequency = <38400000>;
186 vdds_csib-supply = <&vaux2>;
188 pinctrl-names = "default";
189 pinctrl-0 = <&camera_pins>;
196 remote-endpoint = <&csi_cam1>;
197 bus-type = <3>; /* CCP2 */
200 lane-polarity = <0 0>;
201 /* Select strobe = <1> for back camera, <0> for front camera */
209 pinctrl-names = "default";
211 uart2_pins: pinmux_uart2_pins {
212 pinctrl-single,pins = <
213 OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_cts */
214 OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0) /* uart2_rts */
215 OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0) /* uart2_tx */
216 OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0) /* uart2_rx */
220 uart3_pins: pinmux_uart3_pins {
221 pinctrl-single,pins = <
222 OMAP3_CORE1_IOPAD(0x219e, PIN_INPUT | MUX_MODE0) /* uart3_rx */
223 OMAP3_CORE1_IOPAD(0x21a0, PIN_OUTPUT | MUX_MODE0) /* uart3_tx */
227 ethernet_pins: pinmux_ethernet_pins {
228 pinctrl-single,pins = <
229 OMAP3_CORE1_IOPAD(0x20b4, PIN_INPUT_PULLDOWN | MUX_MODE4) /* gpmc_ncs3.gpio_54 */
230 OMAP3_CORE1_IOPAD(0x20fc, PIN_OUTPUT | MUX_MODE4) /* dss_data16.gpio_86 */
231 OMAP3_CORE1_IOPAD(0x219c, PIN_OUTPUT | MUX_MODE4) /* uart3_rts_sd.gpio_164 */
235 gpmc_pins: pinmux_gpmc_pins {
236 pinctrl-single,pins = <
239 OMAP3_CORE1_IOPAD(0x207a, PIN_OUTPUT | MUX_MODE0) /* gpmc_a1.gpmc_a1 */
240 OMAP3_CORE1_IOPAD(0x207c, PIN_OUTPUT | MUX_MODE0) /* gpmc_a2.gpmc_a2 */
241 OMAP3_CORE1_IOPAD(0x207e, PIN_OUTPUT | MUX_MODE0) /* gpmc_a3.gpmc_a3 */
243 /* data lines, gpmc_d0..d7 not muxable according to TRM */
244 OMAP3_CORE1_IOPAD(0x209e, PIN_INPUT | MUX_MODE0) /* gpmc_d8.gpmc_d8 */
245 OMAP3_CORE1_IOPAD(0x20a0, PIN_INPUT | MUX_MODE0) /* gpmc_d9.gpmc_d9 */
246 OMAP3_CORE1_IOPAD(0x20a2, PIN_INPUT | MUX_MODE0) /* gpmc_d10.gpmc_d10 */
247 OMAP3_CORE1_IOPAD(0x20a4, PIN_INPUT | MUX_MODE0) /* gpmc_d11.gpmc_d11 */
248 OMAP3_CORE1_IOPAD(0x20a6, PIN_INPUT | MUX_MODE0) /* gpmc_d12.gpmc_d12 */
249 OMAP3_CORE1_IOPAD(0x20a8, PIN_INPUT | MUX_MODE0) /* gpmc_d13.gpmc_d13 */
250 OMAP3_CORE1_IOPAD(0x20aa, PIN_INPUT | MUX_MODE0) /* gpmc_d14.gpmc_d14 */
251 OMAP3_CORE1_IOPAD(0x20ac, PIN_INPUT | MUX_MODE0) /* gpmc_d15.gpmc_d15 */
254 * gpmc_ncs0, gpmc_nadv_ale, gpmc_noe, gpmc_nwe, gpmc_wait0 not muxable
255 * according to TRM. OneNAND seems to require PIN_INPUT on clock.
257 OMAP3_CORE1_IOPAD(0x20b0, PIN_OUTPUT | MUX_MODE0) /* gpmc_ncs1.gpmc_ncs1 */
258 OMAP3_CORE1_IOPAD(0x20be, PIN_INPUT | MUX_MODE0) /* gpmc_clk.gpmc_clk */
262 i2c1_pins: pinmux_i2c1_pins {
263 pinctrl-single,pins = <
264 OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0) /* i2c1_scl */
265 OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0) /* i2c1_sda */
269 i2c2_pins: pinmux_i2c2_pins {
270 pinctrl-single,pins = <
271 OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT | MUX_MODE0) /* i2c2_scl */
272 OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT | MUX_MODE0) /* i2c2_sda */
276 i2c3_pins: pinmux_i2c3_pins {
277 pinctrl-single,pins = <
278 OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0) /* i2c3_scl */
279 OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0) /* i2c3_sda */
283 debug_leds: pinmux_debug_led_pins {
284 pinctrl-single,pins = <
285 OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4) /* mcbsp1_clkx.gpio_162 */
289 mcspi4_pins: pinmux_mcspi4_pins {
290 pinctrl-single,pins = <
291 OMAP3_CORE1_IOPAD(0x218c, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mcspi4_clk */
292 OMAP3_CORE1_IOPAD(0x2192, PIN_INPUT_PULLDOWN | MUX_MODE1) /* mcspi4_somi */
293 OMAP3_CORE1_IOPAD(0x2190, PIN_OUTPUT | MUX_MODE1) /* mcspi4_simo */
294 OMAP3_CORE1_IOPAD(0x2196, PIN_OUTPUT | MUX_MODE1) /* mcspi4_cs0 */
298 mmc1_pins: pinmux_mmc1_pins {
299 pinctrl-single,pins = <
300 OMAP3_CORE1_IOPAD(0x2144, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk */
301 OMAP3_CORE1_IOPAD(0x2146, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd */
302 OMAP3_CORE1_IOPAD(0x2148, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0 */
303 OMAP3_CORE1_IOPAD(0x214a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1 */
304 OMAP3_CORE1_IOPAD(0x214c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2 */
305 OMAP3_CORE1_IOPAD(0x214e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3 */
309 mmc2_pins: pinmux_mmc2_pins {
310 pinctrl-single,pins = <
311 OMAP3_CORE1_IOPAD(0x2158, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk */
312 OMAP3_CORE1_IOPAD(0x215a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd */
313 OMAP3_CORE1_IOPAD(0x215c, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0 */
314 OMAP3_CORE1_IOPAD(0x215e, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1 */
315 OMAP3_CORE1_IOPAD(0x2160, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2 */
316 OMAP3_CORE1_IOPAD(0x2162, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3 */
317 OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat4 */
318 OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat5 */
319 OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat6 */
320 OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat7 */
324 acx565akm_pins: pinmux_acx565akm_pins {
325 pinctrl-single,pins = <
326 OMAP3_CORE1_IOPAD(0x2104, PIN_OUTPUT | MUX_MODE4) /* RX51_LCD_RESET_GPIO */
330 dss_sdi_pins: pinmux_dss_sdi_pins {
331 pinctrl-single,pins = <
332 OMAP3_CORE1_IOPAD(0x20f0, PIN_OUTPUT | MUX_MODE1) /* dss_data10.sdi_dat1n */
333 OMAP3_CORE1_IOPAD(0x20f2, PIN_OUTPUT | MUX_MODE1) /* dss_data11.sdi_dat1p */
334 OMAP3_CORE1_IOPAD(0x20f4, PIN_OUTPUT | MUX_MODE1) /* dss_data12.sdi_dat2n */
335 OMAP3_CORE1_IOPAD(0x20f6, PIN_OUTPUT | MUX_MODE1) /* dss_data13.sdi_dat2p */
337 OMAP3_CORE1_IOPAD(0x2108, PIN_OUTPUT | MUX_MODE1) /* dss_data22.sdi_clkp */
338 OMAP3_CORE1_IOPAD(0x210a, PIN_OUTPUT | MUX_MODE1) /* dss_data23.sdi_clkn */
342 wl1251_pins: pinmux_wl1251 {
343 pinctrl-single,pins = <
344 OMAP3_CORE1_IOPAD(0x20fe, PIN_OUTPUT | MUX_MODE4) /* gpio 87 => wl1251 enable */
345 OMAP3_CORE1_IOPAD(0x208a, PIN_INPUT | MUX_MODE4) /* gpio 42 => wl1251 irq */
349 ssi_pins: pinmux_ssi {
350 pinctrl-single,pins = <
351 OMAP3_CORE1_IOPAD(0x2180, PIN_INPUT_PULLUP | MUX_MODE1) /* ssi1_rdy_tx */
352 OMAP3_CORE1_IOPAD(0x217e, PIN_OUTPUT | MUX_MODE1) /* ssi1_flag_tx */
353 OMAP3_CORE1_IOPAD(0x2182, PIN_INPUT | MUX_MODE4) /* ssi1_wake_tx (cawake) */
354 OMAP3_CORE1_IOPAD(0x217c, PIN_OUTPUT | MUX_MODE1) /* ssi1_dat_tx */
355 OMAP3_CORE1_IOPAD(0x2184, PIN_INPUT | MUX_MODE1) /* ssi1_dat_rx */
356 OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE1) /* ssi1_flag_rx */
357 OMAP3_CORE1_IOPAD(0x2188, PIN_OUTPUT | MUX_MODE1) /* ssi1_rdy_rx */
358 OMAP3_CORE1_IOPAD(0x218a, PIN_OUTPUT | MUX_MODE1) /* ssi1_wake */
362 modem_pins: pinmux_modem {
363 pinctrl-single,pins = <
364 OMAP3_CORE1_IOPAD(0x20dc, PIN_OUTPUT | MUX_MODE4) /* gpio 70 => cmt_apeslpx */
365 OMAP3_CORE1_IOPAD(0x20e0, PIN_INPUT | MUX_MODE4) /* gpio 72 => ape_rst_rq */
366 OMAP3_CORE1_IOPAD(0x20e2, PIN_OUTPUT | MUX_MODE4) /* gpio 73 => cmt_rst_rq */
367 OMAP3_CORE1_IOPAD(0x20e4, PIN_OUTPUT | MUX_MODE4) /* gpio 74 => cmt_en */
368 OMAP3_CORE1_IOPAD(0x20e6, PIN_OUTPUT | MUX_MODE4) /* gpio 75 => cmt_rst */
369 OMAP3_CORE1_IOPAD(0x218e, PIN_OUTPUT | MUX_MODE4) /* gpio 157 => cmt_bsi */
373 camera_pins: pinmux_camera {
374 pinctrl-single,pins = <
375 OMAP3_CORE1_IOPAD(0x210c, PIN_OUTPUT | MUX_MODE7) /* cam_hs */
376 OMAP3_CORE1_IOPAD(0x210e, PIN_OUTPUT | MUX_MODE7) /* cam_vs */
377 OMAP3_CORE1_IOPAD(0x2110, PIN_OUTPUT | MUX_MODE0) /* cam_xclka */
378 OMAP3_CORE1_IOPAD(0x211e, PIN_OUTPUT | MUX_MODE7) /* cam_d4 */
379 OMAP3_CORE1_IOPAD(0x2122, PIN_INPUT | MUX_MODE0) /* cam_d6 */
380 OMAP3_CORE1_IOPAD(0x2124, PIN_INPUT | MUX_MODE0) /* cam_d7 */
381 OMAP3_CORE1_IOPAD(0x2126, PIN_INPUT | MUX_MODE0) /* cam_d8 */
382 OMAP3_CORE1_IOPAD(0x2128, PIN_INPUT | MUX_MODE0) /* cam_d9 */
383 OMAP3_CORE1_IOPAD(0x212a, PIN_OUTPUT | MUX_MODE7) /* cam_d10 */
384 OMAP3_CORE1_IOPAD(0x212e, PIN_OUTPUT | MUX_MODE7) /* cam_xclkb */
385 OMAP3_CORE1_IOPAD(0x2132, PIN_OUTPUT | MUX_MODE0) /* cam_strobe */
391 pinctrl-names = "default";
392 pinctrl-0 = <&i2c1_pins>;
394 clock-frequency = <2200000>;
398 interrupts = <7>; /* SYS_NIRQ cascaded to intc */
399 interrupt-parent = <&intc>;
403 #include "twl4030.dtsi"
404 #include "twl4030_omap3.dtsi"
407 regulator-name = "V28";
408 regulator-min-microvolt = <2800000>;
409 regulator-max-microvolt = <2800000>;
410 regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
411 regulator-always-on; /* due to battery cover sensor */
415 regulator-name = "VCSI";
416 regulator-min-microvolt = <1800000>;
417 regulator-max-microvolt = <1800000>;
418 regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
422 regulator-name = "VMMC2_30";
423 regulator-min-microvolt = <2800000>;
424 regulator-max-microvolt = <3000000>;
425 regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
429 regulator-name = "VCAM_ANA_28";
430 regulator-min-microvolt = <2800000>;
431 regulator-max-microvolt = <2800000>;
432 regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
436 regulator-name = "VMMC1";
437 regulator-min-microvolt = <1850000>;
438 regulator-max-microvolt = <3150000>;
439 regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
443 regulator-name = "V28_A";
444 regulator-min-microvolt = <2800000>;
445 regulator-max-microvolt = <3000000>;
446 regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
447 regulator-always-on; /* due VIO leak to AIC34 VDDs */
451 regulator-name = "VPLL";
452 regulator-min-microvolt = <1800000>;
453 regulator-max-microvolt = <1800000>;
454 regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
459 regulator-name = "VSDI_CSI";
460 regulator-min-microvolt = <1800000>;
461 regulator-max-microvolt = <1800000>;
462 regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
467 regulator-name = "VMMC2_IO_18";
468 regulator-min-microvolt = <1800000>;
469 regulator-max-microvolt = <1800000>;
470 regulator-initial-mode = <0x0e>; /* RES_STATE_ACTIVE */
474 regulator-name = "VIO";
475 regulator-min-microvolt = <1800000>;
476 regulator-max-microvolt = <1800000>;
480 regulator-name = "VINTANA1";
481 /* fixed to 1500000 */
486 regulator-name = "VINTANA2";
487 regulator-min-microvolt = <2750000>;
488 regulator-max-microvolt = <2750000>;
493 regulator-name = "VINTDIG";
494 /* fixed to 1500000 */
498 /* First two dma channels are reserved on secure omap3 */
500 dma-channel-mask = <0xfffffffc>;
505 compatible = "ti,twl4030-audio";
506 ti,enable-vibra = <1>;
510 compatible = "ti,twl4030-power-n900", "ti,twl4030-power-idle-osc-off";
516 linux,keymap = < MATRIX_KEY(0x00, 0x00, KEY_Q)
517 MATRIX_KEY(0x00, 0x01, KEY_O)
518 MATRIX_KEY(0x00, 0x02, KEY_P)
519 MATRIX_KEY(0x00, 0x03, KEY_COMMA)
520 MATRIX_KEY(0x00, 0x04, KEY_BACKSPACE)
521 MATRIX_KEY(0x00, 0x06, KEY_A)
522 MATRIX_KEY(0x00, 0x07, KEY_S)
524 MATRIX_KEY(0x01, 0x00, KEY_W)
525 MATRIX_KEY(0x01, 0x01, KEY_D)
526 MATRIX_KEY(0x01, 0x02, KEY_F)
527 MATRIX_KEY(0x01, 0x03, KEY_G)
528 MATRIX_KEY(0x01, 0x04, KEY_H)
529 MATRIX_KEY(0x01, 0x05, KEY_J)
530 MATRIX_KEY(0x01, 0x06, KEY_K)
531 MATRIX_KEY(0x01, 0x07, KEY_L)
533 MATRIX_KEY(0x02, 0x00, KEY_E)
534 MATRIX_KEY(0x02, 0x01, KEY_DOT)
535 MATRIX_KEY(0x02, 0x02, KEY_UP)
536 MATRIX_KEY(0x02, 0x03, KEY_ENTER)
537 MATRIX_KEY(0x02, 0x05, KEY_Z)
538 MATRIX_KEY(0x02, 0x06, KEY_X)
539 MATRIX_KEY(0x02, 0x07, KEY_C)
540 MATRIX_KEY(0x02, 0x08, KEY_F9)
542 MATRIX_KEY(0x03, 0x00, KEY_R)
543 MATRIX_KEY(0x03, 0x01, KEY_V)
544 MATRIX_KEY(0x03, 0x02, KEY_B)
545 MATRIX_KEY(0x03, 0x03, KEY_N)
546 MATRIX_KEY(0x03, 0x04, KEY_M)
547 MATRIX_KEY(0x03, 0x05, KEY_SPACE)
548 MATRIX_KEY(0x03, 0x06, KEY_SPACE)
549 MATRIX_KEY(0x03, 0x07, KEY_LEFT)
551 MATRIX_KEY(0x04, 0x00, KEY_T)
552 MATRIX_KEY(0x04, 0x01, KEY_DOWN)
553 MATRIX_KEY(0x04, 0x02, KEY_RIGHT)
554 MATRIX_KEY(0x04, 0x04, KEY_LEFTCTRL)
555 MATRIX_KEY(0x04, 0x05, KEY_RIGHTALT)
556 MATRIX_KEY(0x04, 0x06, KEY_LEFTSHIFT)
557 MATRIX_KEY(0x04, 0x08, KEY_F10)
559 MATRIX_KEY(0x05, 0x00, KEY_Y)
560 MATRIX_KEY(0x05, 0x08, KEY_F11)
562 MATRIX_KEY(0x06, 0x00, KEY_U)
564 MATRIX_KEY(0x07, 0x00, KEY_I)
565 MATRIX_KEY(0x07, 0x01, KEY_F7)
566 MATRIX_KEY(0x07, 0x02, KEY_F8)
572 ti,pulldowns = <0x03ff3f>; /* BIT(0..5) | BIT(8..17) */
576 pinctrl-names = "default";
577 pinctrl-0 = <&i2c2_pins>;
579 clock-frequency = <100000>;
581 tlv320aic3x: tlv320aic3x@18 {
582 compatible = "ti,tlv320aic3x";
584 reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; /* 60 */
586 0 /* AIC3X_GPIO1_FUNC_DISABLED */
587 5 /* AIC3X_GPIO2_FUNC_DIGITAL_MIC_INPUT */
590 AVDD-supply = <&vmmc2>;
591 DRVDD-supply = <&vmmc2>;
592 IOVDD-supply = <&vio>;
593 DVDD-supply = <&vio>;
595 ai3x-micbias-vg = <1>;
598 tlv320aic3x_aux: tlv320aic3x@19 {
599 compatible = "ti,tlv320aic3x";
601 reset-gpios = <&gpio2 28 GPIO_ACTIVE_LOW>; /* 60 */
603 AVDD-supply = <&vmmc2>;
604 DRVDD-supply = <&vmmc2>;
605 IOVDD-supply = <&vio>;
606 DVDD-supply = <&vio>;
608 ai3x-micbias-vg = <2>;
611 tsl2563: tsl2563@29 {
612 compatible = "amstaos,tsl2563";
615 amstaos,cover-comp-gain = <16>;
618 adp1653: led-controller@30 {
619 compatible = "adi,adp1653";
621 enable-gpios = <&gpio3 24 GPIO_ACTIVE_HIGH>; /* 88 */
624 flash-timeout-us = <500000>;
625 flash-max-microamp = <320000>;
626 led-max-microamp = <50000>;
629 led-max-microamp = <17500>;
634 #address-cells = <1>;
636 compatible = "national,lp5523";
638 clock-mode = /bits/ 8 <0>; /* LP55XX_CLOCK_AUTO */
639 enable-gpios = <&gpio2 9 GPIO_ACTIVE_HIGH>; /* 41 */
643 chan-name = "lp5523:kb1";
644 led-cur = /bits/ 8 <50>;
645 max-cur = /bits/ 8 <100>;
646 color = <LED_COLOR_ID_WHITE>;
647 function = LED_FUNCTION_KBD_BACKLIGHT;
652 chan-name = "lp5523:kb2";
653 led-cur = /bits/ 8 <50>;
654 max-cur = /bits/ 8 <100>;
655 color = <LED_COLOR_ID_WHITE>;
656 function = LED_FUNCTION_KBD_BACKLIGHT;
661 chan-name = "lp5523:kb3";
662 led-cur = /bits/ 8 <50>;
663 max-cur = /bits/ 8 <100>;
664 color = <LED_COLOR_ID_WHITE>;
665 function = LED_FUNCTION_KBD_BACKLIGHT;
670 chan-name = "lp5523:kb4";
671 led-cur = /bits/ 8 <50>;
672 max-cur = /bits/ 8 <100>;
673 color = <LED_COLOR_ID_WHITE>;
674 function = LED_FUNCTION_KBD_BACKLIGHT;
679 chan-name = "lp5523:b";
680 led-cur = /bits/ 8 <50>;
681 max-cur = /bits/ 8 <100>;
682 color = <LED_COLOR_ID_BLUE>;
683 function = LED_FUNCTION_STATUS;
688 chan-name = "lp5523:g";
689 led-cur = /bits/ 8 <50>;
690 max-cur = /bits/ 8 <100>;
691 color = <LED_COLOR_ID_GREEN>;
692 function = LED_FUNCTION_STATUS;
697 chan-name = "lp5523:r";
698 led-cur = /bits/ 8 <50>;
699 max-cur = /bits/ 8 <100>;
700 color = <LED_COLOR_ID_RED>;
701 function = LED_FUNCTION_STATUS;
706 chan-name = "lp5523:kb5";
707 led-cur = /bits/ 8 <50>;
708 max-cur = /bits/ 8 <100>;
709 color = <LED_COLOR_ID_WHITE>;
710 function = LED_FUNCTION_KBD_BACKLIGHT;
715 chan-name = "lp5523:kb6";
716 led-cur = /bits/ 8 <50>;
717 max-cur = /bits/ 8 <100>;
718 color = <LED_COLOR_ID_WHITE>;
719 function = LED_FUNCTION_KBD_BACKLIGHT;
723 bq27200: bq27200@55 {
724 compatible = "ti,bq27200";
726 power-supplies = <&bq24150a>;
729 /* Stereo headphone amplifier */
730 tpa6130a2: tpa6130a2@60 {
731 compatible = "ti,tpa6130a2";
734 Vdd-supply = <&vmmc2>;
736 power-gpio = <&gpio4 2 GPIO_ACTIVE_HIGH>; /* 98 */
740 compatible = "silabs,si4713";
743 interrupts-extended = <&gpio2 21 IRQ_TYPE_EDGE_FALLING>; /* 53 */
744 reset-gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>; /* 163 */
746 vdd-supply = <&vaux1>;
749 bq24150a: bq24150a@6b {
750 compatible = "ti,bq24150a";
753 ti,current-limit = <100>;
754 ti,weak-battery-voltage = <3400>;
755 ti,battery-regulation-voltage = <4200>;
756 ti,charge-current = <650>;
757 ti,termination-current = <100>;
758 ti,resistor-sense = <68>;
760 ti,usb-charger-detection = <&isp1707>;
765 pinctrl-names = "default";
766 pinctrl-0 = <&i2c3_pins>;
768 clock-frequency = <400000>;
770 lis302dl: lis3lv02d@1d {
771 compatible = "st,lis3lv02d";
774 Vdd-supply = <&vaux1>;
775 Vdd_IO-supply = <&vio>;
777 interrupt-parent = <&gpio6>;
778 interrupts = <21 20>; /* 181 and 180 */
785 /* Limits are 0.5g * value */
786 st,click-threshold-x = <8>;
787 st,click-threshold-y = <8>;
788 st,click-threshold-z = <10>;
790 /* Click must be longer than time limit */
791 st,click-time-limit = <9>;
793 /* Kind of debounce filter */
794 st,click-latency = <50>;
796 /* Interrupt line 2 for click detection */
801 st,wakeup-threshold = <(800/18)>; /* millig-value / 18 to get HW values */
804 st,wakeup2-threshold = <(900/18)>; /* millig-value / 18 to get HW values */
809 st,axis-x = <1>; /* LIS3_DEV_X */
810 st,axis-y = <(-2)>; /* LIS3_INV_DEV_Y */
811 st,axis-z = <(-3)>; /* LIS3_INV_DEV_Z */
813 st,min-limit-x = <(-32)>;
814 st,min-limit-y = <3>;
815 st,min-limit-z = <3>;
817 st,max-limit-x = <(-3)>;
818 st,max-limit-y = <32>;
819 st,max-limit-z = <32>;
823 compatible = "toshiba,et8ek8";
826 vana-supply = <&vaux4>;
829 clock-names = "extclk";
830 clock-frequency = <9600000>;
832 reset-gpio = <&gpio4 6 GPIO_ACTIVE_HIGH>; /* 102 */
834 lens-focus = <&ad5820>;
838 bus-type = <3>; /* CCP2 */
843 remote-endpoint = <&csi_isp>;
848 /* D/A converter for auto-focus */
850 compatible = "adi,ad5820";
853 VANA-supply = <&vaux4>;
855 #io-channel-cells = <0>;
860 pinctrl-names = "default";
861 pinctrl-0 = <&mmc1_pins>;
862 vmmc-supply = <&vmmc1>;
866 /* most boards use vaux3, only some old versions use vmmc2 instead */
868 pinctrl-names = "default";
869 pinctrl-0 = <&mmc2_pins>;
870 vmmc-supply = <&vaux3>;
871 vqmmc-supply = <&vsim>;
883 ranges = <0 0 0x01000000 0x01000000>, /* 16 MB for OneNAND */
884 <1 0 0x02000000 0x01000000>; /* 16 MB for smc91c96 */
885 pinctrl-names = "default";
886 pinctrl-0 = <&gpmc_pins>;
888 /* sys_ndmareq1 could be used by the driver, not as gpio65 though */
890 #address-cells = <1>;
892 compatible = "ti,omap2-onenand";
893 reg = <0 0 0x20000>; /* CS0, offset 0, IO size 128K */
896 * These timings are based on CONFIG_OMAP_GPMC_DEBUG=y reported
897 * bootloader set values when booted with v5.1
898 * (OneNAND Manufacturer: Samsung):
900 * cs0 GPMC_CS_CONFIG1: 0xfb001202
901 * cs0 GPMC_CS_CONFIG2: 0x00111100
902 * cs0 GPMC_CS_CONFIG3: 0x00020200
903 * cs0 GPMC_CS_CONFIG4: 0x11001102
904 * cs0 GPMC_CS_CONFIG5: 0x03101616
905 * cs0 GPMC_CS_CONFIG6: 0x90060000
909 gpmc,burst-length = <16>;
913 gpmc,device-width = <2>;
914 gpmc,mux-add-data = <2>;
916 gpmc,cs-rd-off-ns = <102>;
917 gpmc,cs-wr-off-ns = <102>;
918 gpmc,adv-on-ns = <0>;
919 gpmc,adv-rd-off-ns = <12>;
920 gpmc,adv-wr-off-ns = <12>;
921 gpmc,oe-on-ns = <12>;
922 gpmc,oe-off-ns = <102>;
924 gpmc,we-off-ns = <102>;
925 gpmc,rd-cycle-ns = <132>;
926 gpmc,wr-cycle-ns = <132>;
927 gpmc,access-ns = <96>;
928 gpmc,page-burst-access-ns = <18>;
929 gpmc,bus-turnaround-ns = <0>;
930 gpmc,cycle2cycle-delay-ns = <0>;
931 gpmc,wait-monitoring-ns = <0>;
932 gpmc,clk-activation-ns = <6>;
933 gpmc,wr-data-mux-bus-ns = <36>;
934 gpmc,wr-access-ns = <96>;
935 gpmc,sync-clk-ps = <15000>;
938 * MTD partition table corresponding to Nokia's
939 * Maemo 5 (Fremantle) release.
942 label = "bootloader";
943 reg = <0x00000000 0x00020000>;
948 reg = <0x00020000 0x00060000>;
952 reg = <0x00080000 0x00040000>;
956 reg = <0x000c0000 0x00200000>;
960 reg = <0x002c0000 0x00200000>;
964 reg = <0x004c0000 0x0fb40000>;
968 /* Ethernet is on some early development boards and qemu */
970 compatible = "smsc,lan91c94";
971 interrupt-parent = <&gpio2>;
972 interrupts = <22 IRQ_TYPE_LEVEL_HIGH>; /* gpio54 */
973 reg = <1 0 0xf>; /* 16 byte IO range */
975 pinctrl-names = "default";
976 pinctrl-0 = <ðernet_pins>;
977 power-gpios = <&gpio3 22 GPIO_ACTIVE_HIGH>; /* gpio86 */
978 reset-gpios = <&gpio6 4 GPIO_ACTIVE_HIGH>; /* gpio164 */
979 gpmc,device-width = <2>;
980 gpmc,sync-clk-ps = <0>;
982 gpmc,cs-rd-off-ns = <48>;
983 gpmc,cs-wr-off-ns = <24>;
984 gpmc,adv-on-ns = <0>;
985 gpmc,adv-rd-off-ns = <0>;
986 gpmc,adv-wr-off-ns = <0>;
987 gpmc,we-on-ns = <12>;
988 gpmc,we-off-ns = <18>;
989 gpmc,oe-on-ns = <12>;
990 gpmc,oe-off-ns = <48>;
991 gpmc,page-burst-access-ns = <0>;
992 gpmc,access-ns = <42>;
993 gpmc,rd-cycle-ns = <180>;
994 gpmc,wr-cycle-ns = <180>;
995 gpmc,bus-turnaround-ns = <0>;
996 gpmc,cycle2cycle-delay-ns = <0>;
997 gpmc,wait-monitoring-ns = <0>;
998 gpmc,clk-activation-ns = <0>;
999 gpmc,wr-access-ns = <0>;
1000 gpmc,wr-data-mux-bus-ns = <12>;
1006 * For some reason, touchscreen is necessary for screen to work at
1007 * all on real hw. It works well without it on emulator.
1009 * Also... order in the device tree actually matters here.
1012 compatible = "ti,tsc2005";
1013 spi-max-frequency = <6000000>;
1016 vio-supply = <&vio>;
1018 reset-gpios = <&gpio4 8 GPIO_ACTIVE_HIGH>; /* 104 */
1019 interrupts-extended = <&gpio4 4 IRQ_TYPE_EDGE_RISING>; /* 100 */
1021 touchscreen-fuzz-x = <4>;
1022 touchscreen-fuzz-y = <7>;
1023 touchscreen-fuzz-pressure = <2>;
1024 touchscreen-size-x = <4096>;
1025 touchscreen-size-y = <4096>;
1026 touchscreen-max-pressure = <2048>;
1028 ti,x-plate-ohms = <280>;
1029 ti,esd-recovery-timeout-ms = <8000>;
1033 compatible = "sony,acx565akm";
1034 spi-max-frequency = <6000000>;
1037 pinctrl-names = "default";
1038 pinctrl-0 = <&acx565akm_pins>;
1041 reset-gpios = <&gpio3 26 GPIO_ACTIVE_HIGH>; /* 90 */
1045 remote-endpoint = <&sdi_out>;
1052 pinctrl-names = "default";
1053 pinctrl-0 = <&mcspi4_pins>;
1056 pinctrl-names = "default";
1057 pinctrl-0 = <&wl1251_pins>;
1059 vio-supply = <&vio>;
1061 compatible = "ti,wl1251";
1063 spi-max-frequency = <48000000>;
1068 ti,power-gpio = <&gpio3 23 GPIO_ACTIVE_HIGH>; /* 87 */
1070 interrupt-parent = <&gpio2>;
1071 interrupts = <10 IRQ_TYPE_NONE>; /* gpio line 42 */
1077 /* RNG not directly accessible on n900, see omap3-rom-rng instead */
1079 status = "disabled";
1083 interface-type = <0>;
1084 usb-phy = <&usb2_phy>;
1086 phy-names = "usb2-phy";
1092 status = "disabled";
1096 pinctrl-names = "default";
1097 pinctrl-0 = <&uart2_pins>;
1099 bcm2048: bluetooth {
1100 compatible = "brcm,bcm2048-nokia", "nokia,h4p-bluetooth";
1101 reset-gpios = <&gpio3 27 GPIO_ACTIVE_LOW>; /* 91 */
1102 host-wakeup-gpios = <&gpio4 5 GPIO_ACTIVE_HIGH>; /* 101 */
1103 bluetooth-wakeup-gpios = <&gpio2 5 GPIO_ACTIVE_HIGH>; /* 37 */
1105 clock-names = "sysclk";
1110 interrupts-extended = <&intc 74 &omap3_pmx_core OMAP3_UART3_RX>;
1111 pinctrl-names = "default";
1112 pinctrl-0 = <&uart3_pins>;
1118 pinctrl-names = "default";
1119 pinctrl-0 = <&dss_sdi_pins>;
1121 vdds_sdi-supply = <&vaux1>;
1124 #address-cells = <1>;
1131 remote-endpoint = <&lcd_in>;
1141 vdda-supply = <&vdac>;
1144 venc_out: endpoint {
1145 remote-endpoint = <&tv_connector_in>;
1156 pinctrl-names = "default";
1157 pinctrl-0 = <&ssi_pins>;
1159 ti,ssi-cawake-gpio = <&gpio5 23 GPIO_ACTIVE_HIGH>; /* 151 */
1162 compatible = "nokia,n900-modem";
1164 pinctrl-names = "default";
1165 pinctrl-0 = <&modem_pins>;
1167 hsi-channel-ids = <0>, <1>, <2>, <3>;
1168 hsi-channel-names = "mcsaab-control",
1172 hsi-speed-kbps = <55000>;
1174 hsi-flow = "synchronized";
1175 hsi-arb-mode = "round-robin";
1177 interrupts-extended = <&gpio3 8 IRQ_TYPE_EDGE_FALLING>; /* 72 */
1179 gpios = <&gpio3 6 GPIO_ACTIVE_HIGH>, /* 70 */
1180 <&gpio3 9 GPIO_ACTIVE_HIGH>, /* 73 */
1181 <&gpio3 10 GPIO_ACTIVE_HIGH>, /* 74 */
1182 <&gpio3 11 GPIO_ACTIVE_HIGH>, /* 75 */
1183 <&gpio5 29 GPIO_ACTIVE_HIGH>; /* 157 */
1184 gpio-names = "cmt_apeslpx",
1193 status = "disabled";