1 // SPDX-License-Identifier: GPL-2.0-only
3 #include <dt-bindings/input/input.h>
13 device_type = "memory";
17 wl12xx_vmmc: wl12xx_vmmc {
18 compatible = "regulator-fixed";
19 regulator-name = "vwl1271";
20 regulator-min-microvolt = <1800000>;
21 regulator-max-microvolt = <1800000>;
22 gpio = <&gpio1 3 0>; /* gpio_3 */
23 startup-delay-us = <70000>;
25 vin-supply = <&vaux3>;
28 /* HS USB Host PHY on PORT 1 */
29 hsusb2_phy: hsusb2_phy {
30 pinctrl-names = "default";
31 pinctrl-0 = <&hsusb2_reset_pin>;
32 compatible = "usb-nop-xceiv";
33 reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* gpio_4 */
37 /* fixed 26MHz oscillator */
38 hfclk_26m: oscillator {
40 compatible = "fixed-clock";
41 clock-frequency = <26000000>;
46 ranges = <0 0 0x30000000 0x1000000>; /* CS0: 16MB for NAND */
49 compatible = "ti,omap2-nand";
50 reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
51 interrupt-parent = <&gpmc>;
52 interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
53 <1 IRQ_TYPE_NONE>; /* termcount */
54 linux,mtd-name = "micron,mt29f4g16abbda3w";
55 nand-bus-width = <16>;
56 ti,nand-ecc-opt = "bch8";
57 rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
58 gpmc,sync-clk-ps = <0>;
60 gpmc,cs-rd-off-ns = <44>;
61 gpmc,cs-wr-off-ns = <44>;
63 gpmc,adv-rd-off-ns = <34>;
64 gpmc,adv-wr-off-ns = <44>;
65 gpmc,we-off-ns = <40>;
66 gpmc,oe-off-ns = <54>;
67 gpmc,access-ns = <64>;
68 gpmc,rd-cycle-ns = <82>;
69 gpmc,wr-cycle-ns = <82>;
70 gpmc,wr-access-ns = <40>;
71 gpmc,wr-data-mux-bus-ns = <0>;
72 gpmc,device-width = <2>;
79 pinctrl-names = "default";
80 pinctrl-0 = <&i2c1_pins>;
81 clock-frequency = <2600000>;
85 interrupts = <7>; /* SYS_NIRQ cascaded to intc */
86 interrupt-parent = <&intc>;
87 clocks = <&hfclk_26m>;
90 compatible = "ti,twl4030-audio";
92 ti,hs_extmute_gpio = <&gpio2 25 GPIO_ACTIVE_HIGH>;
99 pinctrl-names = "default";
100 pinctrl-0 = <&i2c2_pins>;
101 clock-frequency = <400000>;
105 pinctrl-names = "default";
106 pinctrl-0 = <&i2c3_pins>;
107 clock-frequency = <400000>;
109 touchscreen: tsc2004@48 {
110 compatible = "ti,tsc2004";
112 vio-supply = <&vaux1>;
113 pinctrl-names = "default";
114 pinctrl-0 = <&tsc2004_pins>;
115 interrupts-extended = <&gpio5 25 IRQ_TYPE_EDGE_RISING>; /* gpio 153 */
117 touchscreen-fuzz-x = <4>;
118 touchscreen-fuzz-y = <7>;
119 touchscreen-fuzz-pressure = <2>;
120 touchscreen-size-x = <4096>;
121 touchscreen-size-y = <4096>;
122 touchscreen-max-pressure = <2048>;
124 ti,x-plate-ohms = <280>;
125 ti,esd-recovery-timeout-ms = <8000>;
130 interrupts-extended = <&intc 94 &omap3_pmx_core 0x136>;
131 pinctrl-0 = <&mmc3_pins &wl127x_gpio>;
132 pinctrl-names = "default";
133 vmmc-supply = <&wl12xx_vmmc>;
137 #address-cells = <1>;
140 compatible = "ti,wl1273";
142 interrupt-parent = <&gpio1>;
143 interrupts = <2 IRQ_TYPE_EDGE_RISING>; /* gpio 2 */
144 ref-clock-frequency = <26000000>;
149 pinctrl-names = "default";
150 pinctrl-0 = <&hsusb2_pins>;
151 port2-mode = "ehci-phy";
155 phys = <0 &hsusb2_phy>;
160 mmc3_pins: pinmux_mm3_pins {
161 pinctrl-single,pins = <
162 OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */
163 OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */
164 OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */
165 OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */
166 OMAP3_CORE1_IOPAD(0x21d0, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs1.sdmmc3_cmd */
167 OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs2.sdmmc_clk */
170 mcbsp2_pins: pinmux_mcbsp2_pins {
171 pinctrl-single,pins = <
172 OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx */
173 OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0) /* mcbsp2_clkx */
174 OMAP3_CORE1_IOPAD(0x2140, PIN_INPUT | MUX_MODE0) /* mcbsp2_dr */
175 OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0) /* mcbsp2_dx */
178 uart2_pins: pinmux_uart2_pins {
179 pinctrl-single,pins = <
180 OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT | MUX_MODE0) /* uart2_cts.uart2_cts */
181 OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0) /* uart2_rts .uart2_rts*/
182 OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */
183 OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */
184 OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4) /* GPIO_162,BT_EN */
187 mcspi1_pins: pinmux_mcspi1_pins {
188 pinctrl-single,pins = <
189 OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */
190 OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */
191 OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */
192 OMAP3_CORE1_IOPAD(0x21ce, PIN_OUTPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */
196 hsusb2_pins: pinmux_hsusb2_pins {
197 pinctrl-single,pins = <
198 OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */
199 OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */
200 OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */
201 OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */
202 OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */
203 OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */
207 hsusb_otg_pins: pinmux_hsusb_otg_pins {
208 pinctrl-single,pins = <
209 OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */
210 OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */
211 OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */
212 OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */
213 OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT | MUX_MODE0) /* hsusb0_data0.hsusb0_data0 */
214 OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */
215 OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */
216 OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT | MUX_MODE0) /* hsusb0_data3.hsusb0_data3 */
217 OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT | MUX_MODE0) /* hsusb0_data4.hsusb0_data4 */
218 OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT | MUX_MODE0) /* hsusb0_data5.hsusb0_data5 */
219 OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT | MUX_MODE0) /* hsusb0_data6.hsusb0_data6 */
220 OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */
224 i2c1_pins: pinmux_i2c1_pins {
225 pinctrl-single,pins = <
226 OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */
227 OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */
228 OMAP3_CORE1_IOPAD(0x20ba, PIN_OUTPUT | MUX_MODE4) /* gpmc_ncs6.gpio_57 */
232 i2c2_pins: pinmux_i2c2_pins {
233 pinctrl-single,pins = <
234 OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT | MUX_MODE0) /* i2c2_scl */
235 OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT | MUX_MODE0) /* i2c2_sda */
239 i2c3_pins: pinmux_i2c3_pins {
240 pinctrl-single,pins = <
241 OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0) /* i2c3_scl */
242 OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0) /* i2c3_sda */
246 tsc2004_pins: pinmux_tsc2004_pins {
247 pinctrl-single,pins = <
248 OMAP3_CORE1_IOPAD(0x2186, PIN_INPUT | MUX_MODE4) /* mcbsp4_dr.gpio_153 */
255 hsusb2_reset_pin: pinmux_hsusb1_reset_pin {
256 pinctrl-single,pins = <
257 OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4) /* sys_boot2.gpio_4 */
260 wl127x_gpio: pinmux_wl127x_gpio_pin {
261 pinctrl-single,pins = <
262 OMAP3_WKUP_IOPAD(0x2a0a, PIN_INPUT | MUX_MODE4) /* sys_boot0.gpio_2 */
263 OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4) /* sys_boot1.gpio_3 */
269 interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
270 pinctrl-names = "default";
271 pinctrl-0 = <&uart2_pins>;
275 pinctrl-names = "default";
276 pinctrl-0 = <&mcspi1_pins>;
279 #include "twl4030.dtsi"
280 #include "twl4030_omap3.dtsi"
283 regulator-min-microvolt = <2800000>;
284 regulator-max-microvolt = <2800000>;
289 compatible = "ti,twl4030-power-idle-osc-off", "ti,twl4030-power-idle";