2 * This program is free software; you can redistribute it and/or modify
3 * it under the terms of the GNU General Public License version 2 as
4 * published by the Free Software Foundation.
7 #include <dt-bindings/input/input.h>
17 device_type = "memory";
21 wl12xx_vmmc: wl12xx_vmmc {
22 compatible = "regulator-fixed";
23 regulator-name = "vwl1271";
24 regulator-min-microvolt = <1800000>;
25 regulator-max-microvolt = <1800000>;
26 gpio = <&gpio1 3 0>; /* gpio_3 */
27 startup-delay-us = <70000>;
29 vin-supply = <&vmmc2>;
32 /* HS USB Host PHY on PORT 1 */
33 hsusb2_phy: hsusb2_phy {
34 compatible = "usb-nop-xceiv";
35 reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; /* gpio_4 */
40 ranges = <0 0 0x30000000 0x1000000>; /* CS0: 16MB for NAND */
43 compatible = "ti,omap2-nand";
44 reg = <0 0 4>; /* CS0, offset 0, IO size 4 */
45 interrupt-parent = <&gpmc>;
46 interrupts = <0 IRQ_TYPE_NONE>, /* fifoevent */
47 <1 IRQ_TYPE_NONE>; /* termcount */
48 linux,mtd-name = "micron,mt29f4g16abbda3w";
49 nand-bus-width = <16>;
50 ti,nand-ecc-opt = "bch8";
51 rb-gpios = <&gpmc 0 GPIO_ACTIVE_HIGH>; /* gpmc_wait0 */
52 gpmc,sync-clk-ps = <0>;
54 gpmc,cs-rd-off-ns = <44>;
55 gpmc,cs-wr-off-ns = <44>;
57 gpmc,adv-rd-off-ns = <34>;
58 gpmc,adv-wr-off-ns = <44>;
59 gpmc,we-off-ns = <40>;
60 gpmc,oe-off-ns = <54>;
61 gpmc,access-ns = <64>;
62 gpmc,rd-cycle-ns = <82>;
63 gpmc,wr-cycle-ns = <82>;
64 gpmc,wr-access-ns = <40>;
65 gpmc,wr-data-mux-bus-ns = <0>;
66 gpmc,device-width = <2>;
70 /* u-boot uses mtdparts=omap2-nand.0:512k(x-loader),1920k(u-boot),128k(u-boot-env),4m(kernel),-(fs) */
79 reg = <0x80000 0x1e0000>;
82 bootloaders_env@260000 {
84 reg = <0x260000 0x20000>;
89 reg = <0x280000 0x400000>;
94 reg = <0x680000 0>; /* 0 = MTDPART_SIZ_FULL */
100 pinctrl-names = "default";
101 pinctrl-0 = <&i2c1_pins>;
102 clock-frequency = <2600000>;
106 interrupts = <7>; /* SYS_NIRQ cascaded to intc */
107 interrupt-parent = <&intc>;
109 compatible = "ti,twl4030-audio";
111 ti,hs_extmute_gpio = <&gpio2 25 GPIO_ACTIVE_HIGH>;
118 pinctrl-names = "default";
119 pinctrl-0 = <&i2c2_pins>;
120 clock-frequency = <400000>;
124 pinctrl-names = "default";
125 pinctrl-0 = <&i2c3_pins>;
126 clock-frequency = <400000>;
130 interrupts-extended = <&intc 94 &omap3_pmx_core 0x136>;
131 pinctrl-0 = <&mmc3_pins &wl127x_gpio>;
132 pinctrl-names = "default";
133 vmmc-supply = <&wl12xx_vmmc>;
137 #address-cells = <1>;
140 compatible = "ti,wl1273";
142 interrupt-parent = <&gpio1>;
143 interrupts = <2 IRQ_TYPE_LEVEL_HIGH>; /* gpio 2 */
144 ref-clock-frequency = <26000000>;
149 port2-mode = "ehci-phy";
153 phys = <0 &hsusb2_phy>;
158 pinctrl-names = "default";
159 pinctrl-0 = <&hsusb2_pins>;
161 mmc3_pins: pinmux_mm3_pins {
162 pinctrl-single,pins = <
163 OMAP3_CORE1_IOPAD(0x2164, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat4.sdmmc3_dat0 */
164 OMAP3_CORE1_IOPAD(0x2166, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat5.sdmmc3_dat1 */
165 OMAP3_CORE1_IOPAD(0x2168, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat2 */
166 OMAP3_CORE1_IOPAD(0x216a, PIN_INPUT_PULLUP | MUX_MODE3) /* sdmmc2_dat6.sdmmc3_dat3 */
167 OMAP3_CORE1_IOPAD(0x21d0, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs1.sdmmc3_cmd */
168 OMAP3_CORE1_IOPAD(0x21d2, PIN_INPUT_PULLUP | MUX_MODE3) /* mcspi1_cs2.sdmmc_clk */
171 mcbsp2_pins: pinmux_mcbsp2_pins {
172 pinctrl-single,pins = <
173 OMAP3_CORE1_IOPAD(0x213c, PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx */
174 OMAP3_CORE1_IOPAD(0x213e, PIN_INPUT | MUX_MODE0) /* mcbsp2_clkx */
175 OMAP3_CORE1_IOPAD(0x2140, PIN_INPUT | MUX_MODE0) /* mcbsp2_dr */
176 OMAP3_CORE1_IOPAD(0x2142, PIN_OUTPUT | MUX_MODE0) /* mcbsp2_dx */
179 uart2_pins: pinmux_uart2_pins {
180 pinctrl-single,pins = <
181 OMAP3_CORE1_IOPAD(0x2174, PIN_INPUT | MUX_MODE0) /* uart2_cts.uart2_cts */
182 OMAP3_CORE1_IOPAD(0x2176, PIN_OUTPUT | MUX_MODE0) /* uart2_rts .uart2_rts*/
183 OMAP3_CORE1_IOPAD(0x2178, PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */
184 OMAP3_CORE1_IOPAD(0x217a, PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */
185 OMAP3_CORE1_IOPAD(0x2198, PIN_OUTPUT | MUX_MODE4) /* GPIO_162,BT_EN */
188 mcspi1_pins: pinmux_mcspi1_pins {
189 pinctrl-single,pins = <
190 OMAP3_CORE1_IOPAD(0x21c8, PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */
191 OMAP3_CORE1_IOPAD(0x21ca, PIN_OUTPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */
192 OMAP3_CORE1_IOPAD(0x21cc, PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */
193 OMAP3_CORE1_IOPAD(0x21ce, PIN_OUTPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */
197 hsusb2_pins: pinmux_hsusb2_pins {
198 pinctrl-single,pins = <
199 OMAP3_CORE1_IOPAD(0x21d4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi1_cs3.hsusb2_data2 */
200 OMAP3_CORE1_IOPAD(0x21d6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_clk.hsusb2_data7 */
201 OMAP3_CORE1_IOPAD(0x21d8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_simo.hsusb2_data4 */
202 OMAP3_CORE1_IOPAD(0x21da, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_somi.hsusb2_data5 */
203 OMAP3_CORE1_IOPAD(0x21dc, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs0.hsusb2_data6 */
204 OMAP3_CORE1_IOPAD(0x21de, PIN_INPUT_PULLDOWN | MUX_MODE3) /* mcspi2_cs1.hsusb2_data3 */
208 hsusb_otg_pins: pinmux_hsusb_otg_pins {
209 pinctrl-single,pins = <
210 OMAP3_CORE1_IOPAD(0x21a2, PIN_INPUT | MUX_MODE0) /* hsusb0_clk.hsusb0_clk */
211 OMAP3_CORE1_IOPAD(0x21a4, PIN_OUTPUT | MUX_MODE0) /* hsusb0_stp.hsusb0_stp */
212 OMAP3_CORE1_IOPAD(0x21a6, PIN_INPUT | MUX_MODE0) /* hsusb0_dir.hsusb0_dir */
213 OMAP3_CORE1_IOPAD(0x21a8, PIN_INPUT | MUX_MODE0) /* hsusb0_nxt.hsusb0_nxt */
214 OMAP3_CORE1_IOPAD(0x21aa, PIN_INPUT | MUX_MODE0) /* hsusb0_data0.hsusb0_data0 */
215 OMAP3_CORE1_IOPAD(0x21ac, PIN_INPUT | MUX_MODE0) /* hsusb0_data1.hsusb0_data1 */
216 OMAP3_CORE1_IOPAD(0x21ae, PIN_INPUT | MUX_MODE0) /* hsusb0_data2.hsusb0_data2 */
217 OMAP3_CORE1_IOPAD(0x21b0, PIN_INPUT | MUX_MODE0) /* hsusb0_data3.hsusb0_data3 */
218 OMAP3_CORE1_IOPAD(0x21b2, PIN_INPUT | MUX_MODE0) /* hsusb0_data4.hsusb0_data4 */
219 OMAP3_CORE1_IOPAD(0x21b4, PIN_INPUT | MUX_MODE0) /* hsusb0_data5.hsusb0_data5 */
220 OMAP3_CORE1_IOPAD(0x21b6, PIN_INPUT | MUX_MODE0) /* hsusb0_data6.hsusb0_data6 */
221 OMAP3_CORE1_IOPAD(0x21b8, PIN_INPUT | MUX_MODE0) /* hsusb0_data7.hsusb0_data7 */
225 i2c1_pins: pinmux_i2c1_pins {
226 pinctrl-single,pins = <
227 OMAP3_CORE1_IOPAD(0x21ba, PIN_INPUT | MUX_MODE0) /* i2c1_scl.i2c1_scl */
228 OMAP3_CORE1_IOPAD(0x21bc, PIN_INPUT | MUX_MODE0) /* i2c1_sda.i2c1_sda */
229 OMAP3_CORE1_IOPAD(0x20ba, PIN_OUTPUT | MUX_MODE4) /* gpmc_ncs6.gpio_57 */
235 pinctrl-names = "default";
236 pinctrl-0 = <&hsusb2_reset_pin>;
237 hsusb2_reset_pin: pinmux_hsusb1_reset_pin {
238 pinctrl-single,pins = <
239 OMAP3_WKUP_IOPAD(0x2a0e, PIN_OUTPUT | MUX_MODE4) /* sys_boot2.gpio_4 */
242 wl127x_gpio: pinmux_wl127x_gpio_pin {
243 pinctrl-single,pins = <
244 OMAP3_WKUP_IOPAD(0x2a0c, PIN_INPUT | MUX_MODE4) /* sys_boot0.gpio_2 */
245 OMAP3_WKUP_IOPAD(0x2a0c, PIN_OUTPUT | MUX_MODE4) /* sys_boot1.gpio_3 */
248 i2c2_pins: pinmux_i2c2_pins {
249 pinctrl-single,pins = <
250 OMAP3_CORE1_IOPAD(0x21be, PIN_INPUT | MUX_MODE0) /* i2c2_scl */
251 OMAP3_CORE1_IOPAD(0x21c0, PIN_INPUT | MUX_MODE0) /* i2c2_sda */
254 i2c3_pins: pinmux_i2c3_pins {
255 pinctrl-single,pins = <
256 OMAP3_CORE1_IOPAD(0x21c2, PIN_INPUT | MUX_MODE0) /* i2c3_scl */
257 OMAP3_CORE1_IOPAD(0x21c4, PIN_INPUT | MUX_MODE0) /* i2c3_sda */
263 pinctrl-names = "default";
264 pinctrl-0 = <&hsusb2_2_pins>;
265 hsusb2_2_pins: pinmux_hsusb2_2_pins {
266 pinctrl-single,pins = <
267 OMAP3630_CORE2_IOPAD(0x25f0, PIN_OUTPUT | MUX_MODE3) /* etk_d10.hsusb2_clk */
268 OMAP3630_CORE2_IOPAD(0x25f2, PIN_OUTPUT | MUX_MODE3) /* etk_d11.hsusb2_stp */
269 OMAP3630_CORE2_IOPAD(0x25f4, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d12.hsusb2_dir */
270 OMAP3630_CORE2_IOPAD(0x25f6, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d13.hsusb2_nxt */
271 OMAP3630_CORE2_IOPAD(0x25f8, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d14.hsusb2_data0 */
272 OMAP3630_CORE2_IOPAD(0x25fa, PIN_INPUT_PULLDOWN | MUX_MODE3) /* etk_d15.hsusb2_data1 */
278 interrupts-extended = <&intc 73 &omap3_pmx_core OMAP3_UART2_RX>;
279 pinctrl-names = "default";
280 pinctrl-0 = <&uart2_pins>;
284 pinctrl-names = "default";
285 pinctrl-0 = <&mcspi1_pins>;
288 #include "twl4030.dtsi"
289 #include "twl4030_omap3.dtsi"
293 compatible = "ti,twl4030-power-idle-osc-off", "ti,twl4030-power-idle";