arch/arm/boot/dts/gemini-dlink-dir-685.dts

   1 /*
   2  * Device Tree file for D-Link DIR-685 Xtreme N Storage Router
   3  */
   4
   5 /dts-v1/;
   6
   7 #include "gemini.dtsi"
   8 #include <dt-bindings/input/input.h>
   9
  10 / {
  11         model = "D-Link DIR-685 Xtreme N Storage Router";
  12         compatible = "dlink,dir-685", "cortina,gemini";
  13         #address-cells = <1>;
  14         #size-cells = <1>;
  15
  16         memory@0 {
  17                 /* 128 MB SDRAM in 2 x Hynix HY5DU121622DTP-D43 */
  18                 device_type = "memory";
  19                 reg = <0x00000000 0x8000000>;
  20         };
  21
  22         chosen {
  23                 bootargs = "console=ttyS0,19200n8 root=/dev/sda1 rw rootwait";
  24                 stdout-path = "uart0:19200n8";
  25         };
  26
  27         gpio_keys {
  28                 compatible = "gpio-keys";
  29
  30                 button-esc {
  31                         debounce-interval = <50>;
  32                         wakeup-source;
  33                         linux,code = <KEY_ESC>;
  34                         label = "reset";
  35                         /* Collides with LPC_LAD[0], UART DCD, SSP 97RST */
  36                         gpios = <&gpio0 8 GPIO_ACTIVE_LOW>;
  37                 };
  38                 button-eject {
  39                         debounce-interval = <50>;
  40                         wakeup-source;
  41                         linux,code = <KEY_EJECTCD>;
  42                         label = "unmount";
  43                         /* Collides with LPC LFRAME, UART RTS, SSP TXD */
  44                         gpios = <&gpio0 13 GPIO_ACTIVE_LOW>;
  45                 };
  46         };
  47
  48         vdisp: regulator {
  49                 compatible = "regulator-fixed";
  50                 regulator-name = "display-power";
  51                 regulator-min-microvolt = <3600000>;
  52                 regulator-max-microvolt = <3600000>;
  53                 /* Collides with LCD E */
  54                 gpio = <&gpio0 16 GPIO_ACTIVE_HIGH>;
  55                 enable-active-high;
  56         };
  57
  58         spi {
  59                 compatible = "spi-gpio";
  60                 #address-cells = <1>;
  61                 #size-cells = <0>;
  62
  63                 /* Collides with IDE pins, that's cool (we do not use them) */
  64                 gpio-sck = <&gpio1 5 GPIO_ACTIVE_HIGH>;
  65                 gpio-miso = <&gpio1 8 GPIO_ACTIVE_HIGH>;
  66                 gpio-mosi = <&gpio1 7 GPIO_ACTIVE_HIGH>;
  67                 /* Collides with pflash CE1, not so cool */
  68                 cs-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
  69                 num-chipselects = <1>;
  70
  71                 panel: display@0 {
  72                         compatible = "dlink,dir-685-panel", "ilitek,ili9322";
  73                         reg = <0>;
  74                         /* 50 ns min period = 20 MHz */
  75                         spi-max-frequency = <20000000>;
  76                         spi-cpol; /* Clock active low */
  77                         vcc-supply = <&vdisp>;
  78                         iovcc-supply = <&vdisp>;
  79                         vci-supply = <&vdisp>;
  80
  81                         port {
  82                                 panel_in: endpoint {
  83                                         remote-endpoint = <&display_out>;
  84                                 };
  85                         };
  86                 };
  87         };
  88
  89         leds {
  90                 compatible = "gpio-leds";
  91                 led-wps {
  92                         label = "dir685:blue:WPS";
  93                         /* Collides with ICE */
  94                         gpios = <&gpio0 7 GPIO_ACTIVE_LOW>;
  95                         default-state = "on";
  96                         linux,default-trigger = "heartbeat";
  97                 };
  98                 /*
  99                  * These two LEDs are on the side of the device.
 100                  * For electrical reasons, both LEDs cannot be active
 101                  * at the same time so only blue or orange can be on at
 102                  * one time. Enabling both makes the LED go dark.
 103                  * The LEDs both sit inside the unmount button and the
 104                  * label on the case says "unmount".
 105                  */
 106                 led-blue-hd {
 107                         label = "dir685:blue:HD";
 108                         /* Collides with LPC_SERIRQ, UART DTR, SSP FSC pins */
 109                         gpios = <&gpio0 11 GPIO_ACTIVE_HIGH>;
 110                         default-state = "off";
 111                         linux,default-trigger = "disk-read";
 112                 };
 113                 led-orange-hd {
 114                         label = "dir685:orange:HD";
 115                         /* Collides with LPC_LAD[2], UART DSR, SSP ECLK pins */
 116                         gpios = <&gpio0 12 GPIO_ACTIVE_HIGH>;
 117                         default-state = "off";
 118                         linux,default-trigger = "disk-write";
 119                 };
 120         };
 121
 122         /*
 123          * This is a Sunon Maglev GM0502PFV2-8 cooling fan @10000 RPM.
 124          * Since the platform has no temperature sensor, this is controlled
 125          * from userspace by using the hard disks S.M.A.R.T. temperature
 126          * sensor. It is turned on when the temperature exceeds 46 degrees
 127          * and turned off when the temperatures goes below 41 degrees
 128          * (celsius).
 129          */
 130         gpio-fan {
 131                 compatible = "gpio-fan";
 132                 /* Collides with IDE */
 133                 gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
 134                 gpio-fan,speed-map = <0 0>, <10000 1>;
 135                 #cooling-cells = <2>;
 136         };
 137
 138         /*
 139          * The touchpad input is connected to a GPIO bit-banged
 140          * I2C bus.
 141          */
 142         gpio-i2c {
 143                 compatible = "i2c-gpio";
 144                 /* Collides with ICE */
 145                 sda-gpios = <&gpio0 5 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
 146                 scl-gpios = <&gpio0 6 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
 147                 #address-cells = <1>;
 148                 #size-cells = <0>;
 149
 150                 touchkeys@26 {
 151                         compatible = "dlink,dir685-touchkeys";
 152                         reg = <0x26>;
 153                         interrupt-parent = <&gpio0>;
 154                         /* Collides with NAND flash */
 155                         interrupts = <17 IRQ_TYPE_EDGE_FALLING>;
 156                 };
 157         };
 158
 159         /* This is a RealTek RTL8366RB switch and PHY using SMI over GPIO */
 160         switch {
 161                 compatible = "realtek,rtl8366rb";
 162                 /* 22 = MDIO (has input reads), 21 = MDC (clock, output only) */
 163                 mdc-gpios = <&gpio0 21 GPIO_ACTIVE_HIGH>;
 164                 mdio-gpios = <&gpio0 22 GPIO_ACTIVE_HIGH>;
 165                 reset-gpios = <&gpio0 14 GPIO_ACTIVE_LOW>;
 166                 realtek,disable-leds;
 167
 168                 switch_intc: interrupt-controller {
 169                         /* GPIO 15 provides the interrupt */
 170                         interrupt-parent = <&gpio0>;
 171                         interrupts = <15 IRQ_TYPE_LEVEL_LOW>;
 172                         interrupt-controller;
 173                         #address-cells = <0>;
 174                         #interrupt-cells = <1>;
 175                 };
 176
 177                 ports {
 178                         #address-cells = <1>;
 179                         #size-cells = <0>;
 180
 181                         port@0 {
 182                                 reg = <0>;
 183                                 label = "lan0";
 184                                 phy-handle = <&phy0>;
 185                         };
 186                         port@1 {
 187                                 reg = <1>;
 188                                 label = "lan1";
 189                                 phy-handle = <&phy1>;
 190                         };
 191                         port@2 {
 192                                 reg = <2>;
 193                                 label = "lan2";
 194                                 phy-handle = <&phy2>;
 195                         };
 196                         port@3 {
 197                                 reg = <3>;
 198                                 label = "lan3";
 199                                 phy-handle = <&phy3>;
 200                         };
 201                         port@4 {
 202                                 reg = <4>;
 203                                 label = "wan";
 204                                 phy-handle = <&phy4>;
 205                         };
 206                         rtl8366rb_cpu_port: port@5 {
 207                                 reg = <5>;
 208                                 label = "cpu";
 209                                 ethernet = <&gmac0>;
 210                                 phy-mode = "rgmii";
 211                                 fixed-link {
 212                                         speed = <1000>;
 213                                         full-duplex;
 214                                         pause;
 215                                 };
 216                         };
 217
 218                 };
 219
 220                 mdio {
 221                         compatible = "realtek,smi-mdio";
 222                         #address-cells = <1>;
 223                         #size-cells = <0>;
 224
 225                         phy0: phy@0 {
 226                                 reg = <0>;
 227                                 interrupt-parent = <&switch_intc>;
 228                                 interrupts = <0>;
 229                         };
 230                         phy1: phy@1 {
 231                                 reg = <1>;
 232                                 interrupt-parent = <&switch_intc>;
 233                                 interrupts = <1>;
 234                         };
 235                         phy2: phy@2 {
 236                                 reg = <2>;
 237                                 interrupt-parent = <&switch_intc>;
 238                                 interrupts = <2>;
 239                         };
 240                         phy3: phy@3 {
 241                                 reg = <3>;
 242                                 interrupt-parent = <&switch_intc>;
 243                                 interrupts = <3>;
 244                         };
 245                         phy4: phy@4 {
 246                                 reg = <4>;
 247                                 interrupt-parent = <&switch_intc>;
 248                                 interrupts = <12>;
 249                         };
 250                 };
 251         };
 252
 253         soc {
 254                 flash@30000000 {
 255                         /*
 256                          * Flash access is by default disabled, because it
 257                          * collides with the Chip Enable signal for the display
 258                          * panel, that reuse the parallel flash Chip Select 1
 259                          * (CS1). Enabling flash makes graphics stop working.
 260                          *
 261                          * We might be able to hack around this by letting
 262                          * GPIO poke around in the flash controller registers.
 263                          */
 264                         /* status = "okay"; */
 265                         /* 32MB of flash */
 266                         reg = <0x30000000 0x02000000>;
 267
 268                         /*
 269                          * This "RedBoot" is the Storlink derivative.
 270                          */
 271                         partition@0 {
 272                                 label = "RedBoot";
 273                                 reg = <0x00000000 0x00040000>;
 274                                 read-only;
 275                         };
 276                         /*
 277                          * This firmware image contains the kernel catenated
 278                          * with the squashfs root filesystem. For some reason
 279                          * this is called "upgrade" on the vendor system.
 280                          */
 281                         partition@40000 {
 282                                 label = "upgrade";
 283                                 reg = <0x00040000 0x01f40000>;
 284                                 read-only;
 285                         };
 286                         /* RGDB, Residental Gateway Database? */
 287                         partition@1f80000 {
 288                                 label = "rgdb";
 289                                 reg = <0x01f80000 0x00040000>;
 290                                 read-only;
 291                         };
 292                         /*
 293                          * This partition contains MAC addresses for WAN,
 294                          * WLAN and LAN, and the country code (for wireless
 295                          * I guess).
 296                          */
 297                         partition@1fc0000 {
 298                                 label = "nvram";
 299                                 reg = <0x01fc0000 0x00020000>;
 300                                 read-only;
 301                         };
 302                         partition@1fe0000 {
 303                                 label = "LangPack";
 304                                 reg = <0x01fe0000 0x00020000>;
 305                                 read-only;
 306                         };
 307                 };
 308
 309                 syscon: syscon@40000000 {
 310                         pinctrl {
 311                                 /*
 312                                  * gpio0bgrp cover line 5, 6 used by TK I2C
 313                                  * gpio0bgrp cover line 7 used by WPS LED
 314                                  * gpio0cgrp cover line 8, 13 used by keys
 315                                  *           and 11, 12 used by the HD LEDs
 316                                  *           and line 14, 15 used by RTL8366
 317                                  *           RESET and phy ready
 318                                  * gpio0egrp cover line 16 used by VDISP
 319                                  * gpio0fgrp cover line 17 used by TK IRQ
 320                                  * gpio0ggrp cover line 20 used by panel CS
 321                                  * gpio0hgrp cover line 21,22 used by RTL8366RB MDIO
 322                                  */
 323                                 gpio0_default_pins: pinctrl-gpio0 {
 324                                         mux {
 325                                                 function = "gpio0";
 326                                                 groups = "gpio0bgrp",
 327                                                 "gpio0cgrp",
 328                                                 "gpio0egrp",
 329                                                 "gpio0fgrp",
 330                                                 "gpio0ggrp",
 331                                                 "gpio0hgrp";
 332                                         };
 333                                 };
 334                                 /*
 335                                  * gpio1bgrp cover line 5,8,7 used by panel SPI
 336                                  * also line 6 used by the fan
 337                                  *
 338                                  */
 339                                 gpio1_default_pins: pinctrl-gpio1 {
 340                                         mux {
 341                                                 function = "gpio1";
 342                                                 groups = "gpio1bgrp";
 343                                         };
 344                                 };
 345                                 pinctrl-gmii {
 346                                         mux {
 347                                                 function = "gmii";
 348                                                 groups = "gmii_gmac0_grp";
 349                                         };
 350                                         conf0 {
 351                                                 pins = "V8 GMAC0 RXDV", "T10 GMAC1 RXDV",
 352                                                      "Y7 GMAC0 RXC", "Y11 GMAC1 RXC",
 353                                                      "T8 GMAC0 TXEN", "W11 GMAC1 TXEN",
 354                                                      "U8 GMAC0 TXC", "V11 GMAC1 TXC",
 355                                                      "W8 GMAC0 RXD0", "V9 GMAC0 RXD1",
 356                                                      "Y8 GMAC0 RXD2", "U9 GMAC0 RXD3",
 357                                                      "T7 GMAC0 TXD0", "U6 GMAC0 TXD1",
 358                                                      "V7 GMAC0 TXD2", "U7 GMAC0 TXD3",
 359                                                      "Y12 GMAC1 RXD0", "V12 GMAC1 RXD1",
 360                                                      "T11 GMAC1 RXD2", "W12 GMAC1 RXD3",
 361                                                      "U10 GMAC1 TXD0", "Y10 GMAC1 TXD1",
 362                                                      "W10 GMAC1 TXD2", "T9 GMAC1 TXD3";
 363                                                 skew-delay = <7>;
 364                                         };
 365                                         /* Set up drive strength on GMAC0 to 16 mA */
 366                                         conf1 {
 367                                                 groups = "gmii_gmac0_grp";
 368                                                 drive-strength = <16>;
 369                                         };
 370                                 };
 371                         };
 372                 };
 373
 374                 sata: sata@46000000 {
 375                         cortina,gemini-ata-muxmode = <0>;
 376                         cortina,gemini-enable-sata-bridge;
 377                         status = "okay";
 378                 };
 379
 380                 gpio0: gpio@4d000000 {
 381                         pinctrl-names = "default";
 382                         pinctrl-0 = <&gpio0_default_pins>;
 383                 };
 384
 385                 gpio1: gpio@4e000000 {
 386                         pinctrl-names = "default";
 387                         pinctrl-0 = <&gpio1_default_pins>;
 388                 };
 389
 390                 pci@50000000 {
 391                         status = "okay";
 392                         interrupt-map-mask = <0xf800 0 0 7>;
 393                         interrupt-map =
 394                                 <0x4800 0 0 1 &pci_intc 0>, /* Slot 9 */
 395                                 <0x4800 0 0 2 &pci_intc 1>,
 396                                 <0x4800 0 0 3 &pci_intc 2>,
 397                                 <0x4800 0 0 4 &pci_intc 3>,
 398                                 <0x5000 0 0 1 &pci_intc 1>, /* Slot 10 */
 399                                 <0x5000 0 0 2 &pci_intc 2>,
 400                                 <0x5000 0 0 3 &pci_intc 3>,
 401                                 <0x5000 0 0 4 &pci_intc 0>,
 402                                 <0x5800 0 0 1 &pci_intc 2>, /* Slot 11 */
 403                                 <0x5800 0 0 2 &pci_intc 3>,
 404                                 <0x5800 0 0 3 &pci_intc 0>,
 405                                 <0x5800 0 0 4 &pci_intc 1>,
 406                                 <0x6000 0 0 1 &pci_intc 3>, /* Slot 12 */
 407                                 <0x6000 0 0 2 &pci_intc 0>,
 408                                 <0x6000 0 0 3 &pci_intc 1>,
 409                                 <0x6000 0 0 4 &pci_intc 2>;
 410                 };
 411
 412                 ethernet@60000000 {
 413                         status = "okay";
 414
 415                         ethernet-port@0 {
 416                                 phy-mode = "rgmii";
 417                                 fixed-link {
 418                                         speed = <1000>;
 419                                         full-duplex;
 420                                         pause;
 421                                 };
 422                         };
 423                         ethernet-port@1 {
 424                                 /* Not used in this platform */
 425                         };
 426                 };
 427
 428                 ata@63000000 {
 429                         status = "okay";
 430                 };
 431
 432                 display-controller@6a000000 {
 433                         status = "okay";
 434
 435                         port@0 {
 436                                 reg = <0>;
 437                                 display_out: endpoint {
 438                                         remote-endpoint = <&panel_in>;
 439                                 };
 440                         };
 441                 };
 442         };
 443 };