arch/arm/boot/dts/exynos4412-p4note.dtsi

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * Samsung's Exynos4412 based p4note device family base DT.
   4  * Based on exynos4412-midas.dtsi.
   5  *
   6  * Copyright (c) 2013 Samsung Electronics Co., Ltd.
   7  *              http://www.samsung.com
   8  */
   9
  10 /dts-v1/;
  11 #include "exynos4412.dtsi"
  12 #include "exynos4412-ppmu-common.dtsi"
  13
  14 #include <dt-bindings/clock/maxim,max77686.h>
  15 #include <dt-bindings/gpio/gpio.h>
  16 #include <dt-bindings/input/linux-event-codes.h>
  17 #include <dt-bindings/interrupt-controller/irq.h>
  18 #include <dt-bindings/power/summit,smb347-charger.h>
  19 #include "exynos-pinctrl.h"
  20
  21 / {
  22         compatible = "samsung,p4note", "samsung,exynos4412", "samsung,exynos4";
  23
  24         memory@40000000 {
  25                 device_type = "memory";
  26                 reg = <0x40000000 0x80000000>;
  27         };
  28
  29         chosen {
  30                 stdout-path = &serial_2;
  31         };
  32
  33         firmware@204f000 {
  34                 compatible = "samsung,secure-firmware";
  35                 reg = <0x0204F000 0x1000>;
  36         };
  37
  38         fixed-rate-clocks {
  39                 xxti {
  40                         compatible = "samsung,clock-xxti";
  41                         clock-frequency = <0>;
  42                 };
  43
  44                 xusbxti {
  45                         compatible = "samsung,clock-xusbxti";
  46                         clock-frequency = <24000000>;
  47                 };
  48         };
  49
  50         gpio-keys {
  51                 compatible = "gpio-keys";
  52                 pinctrl-names = "default";
  53                 pinctrl-0 = <&gpio_keys>;
  54
  55                 key-down {
  56                         gpios = <&gpx2 2 GPIO_ACTIVE_LOW>;
  57                         linux,code = <KEY_VOLUMEDOWN>;
  58                         label = "volume down";
  59                         debounce-interval = <10>;
  60                 };
  61
  62                 key-up {
  63                         gpios = <&gpx3 3 GPIO_ACTIVE_LOW>;
  64                         linux,code = <KEY_VOLUMEUP>;
  65                         label = "volume up";
  66                         debounce-interval = <10>;
  67                 };
  68
  69                 key-power {
  70                         gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
  71                         linux,code = <KEY_POWER>;
  72                         label = "power";
  73                         debounce-interval = <10>;
  74                         wakeup-source;
  75                 };
  76         };
  77
  78         voltage-regulator-1 {
  79                 compatible = "regulator-fixed";
  80                 regulator-name = "TSP_LDO1";
  81                 pinctrl-names = "default";
  82                 pinctrl-0 = <&tsp_reg_gpio_1>;
  83                 gpios = <&gpm4 5 GPIO_ACTIVE_HIGH>;
  84                 enable-active-high;
  85                 regulator-always-on;
  86         };
  87
  88         voltage-regulator-2 {
  89                 compatible = "regulator-fixed";
  90                 regulator-name = "TSP_LDO2";
  91                 pinctrl-names = "default";
  92                 pinctrl-0 = <&tsp_reg_gpio_2>;
  93                 gpios = <&gpb 5 GPIO_ACTIVE_HIGH>;
  94                 enable-active-high;
  95                 regulator-always-on;
  96         };
  97
  98         voltage-regulator-3 {
  99                 compatible = "regulator-fixed";
 100                 regulator-name = "TSP_LDO3";
 101                 pinctrl-names = "default";
 102                 pinctrl-0 = <&tsp_reg_gpio_3>;
 103                 gpios = <&gpb 7 GPIO_ACTIVE_HIGH>;
 104                 startup-delay-us = <20000>;
 105                 enable-active-high;
 106                 regulator-always-on;
 107         };
 108
 109         panel_vdd: voltage-regulator-4 {
 110                 compatible = "regulator-fixed";
 111                 regulator-name = "LCD_ENABLE";
 112                 pinctrl-names = "default";
 113                 pinctrl-0 = <&lcd_enable>;
 114                 gpios = <&gpc0 1 GPIO_ACTIVE_HIGH>;
 115                 enable-active-high;
 116                 regulator-boot-on;
 117         };
 118
 119         wlan_pwrseq: sdhci3-pwrseq {
 120                 compatible = "mmc-pwrseq-simple";
 121                 reset-gpios = <&gpm3 5 GPIO_ACTIVE_LOW>;
 122                 pinctrl-0 = <&wifi_reset>;
 123                 pinctrl-names = "default";
 124                 clocks = <&max77686 MAX77686_CLK_PMIC>;
 125                 clock-names = "ext_clock";
 126         };
 127
 128         battery_cell: battery-cell {
 129                 compatible = "simple-battery";
 130                 device-chemistry = "lithium-ion";
 131                 constant-charge-current-max-microamp = <2200000>;
 132                 precharge-current-microamp = <250000>;
 133                 charge-term-current-microamp = <250000>;
 134                 constant-charge-voltage-max-microvolt = <4200000>;
 135
 136                 power-supplies = <&power_supply>;
 137         };
 138
 139         i2c-gpio-1 {
 140                 compatible = "i2c-gpio";
 141                 sda-gpios = <&gpy2 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 142                 scl-gpios = <&gpy2 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 143                 i2c-gpio,delay-us = <2>;
 144                 #address-cells = <1>;
 145                 #size-cells = <0>;
 146
 147                 magnetometer@c {
 148                         compatible = "asahi-kasei,ak8975";
 149                         reg = <0x0c>;
 150                         pinctrl-0 = <&ak8975_irq>;
 151                         pinctrl-names = "default";
 152                         interrupt-parent = <&gpm4>;
 153                         interrupts = <7 IRQ_TYPE_EDGE_RISING>;
 154                 };
 155         };
 156
 157         i2c-gpio-2 {
 158                 compatible = "i2c-gpio";
 159                 sda-gpios = <&gpy0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 160                 scl-gpios = <&gpy0 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 161                 i2c-gpio,delay-us = <2>;
 162                 #address-cells = <1>;
 163                 #size-cells = <0>;
 164
 165                 fuel-gauge@36 {
 166                         compatible = "maxim,max17042";
 167                         reg = <0x36>;
 168                         pinctrl-0 = <&fuel_alert_irq>;
 169                         pinctrl-names = "default";
 170                         interrupt-parent = <&gpx2>;
 171                         interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 172                         maxim,rsns-microohm = <10000>;
 173                         maxim,over-heat-temp = <600>;
 174                         maxim,over-volt = <4300>;
 175                 };
 176         };
 177
 178         i2c-gpio-3 {
 179                 compatible = "i2c-gpio";
 180                 sda-gpios = <&gpm4 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 181                 scl-gpios = <&gpm4 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 182                 i2c-gpio,delay-us = <5>;
 183                 #address-cells = <1>;
 184                 #size-cells = <0>;
 185
 186                 adc@41 {
 187                         compatible = "st,stmpe811";
 188                         reg = <0x41>;
 189                         pinctrl-0 = <&stmpe_adc_irq>;
 190                         pinctrl-names = "default";
 191                         interrupt-parent = <&gpx0>;
 192                         interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
 193                         interrupt-controller;
 194                         irq-trigger = <0x1>;
 195                         st,adc-freq = <3>;
 196                         st,mod-12b = <1>;
 197                         st,ref-sel = <0>;
 198                         st,sample-time = <3>;
 199
 200                         stmpe_adc {
 201                                 compatible = "st,stmpe-adc";
 202                                 #io-channel-cells = <1>;
 203                                 st,norequest-mask = <0x2F>;
 204                         };
 205                 };
 206         };
 207
 208         i2c-gpio-4 {
 209                 compatible = "i2c-gpio";
 210                 sda-gpios = <&gpm2 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 211                 scl-gpios = <&gpm2 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 212
 213                 i2c-gpio,delay-us = <2>;
 214                 #address-cells = <1>;
 215                 #size-cells = <0>;
 216
 217                 power_supply: charger@6 {
 218                         compatible = "summit,smb347";
 219                         reg = <0x6>;
 220                         summit,enable-usb-charging;
 221                         summit,enable-charge-control = <SMB3XX_CHG_ENABLE_SW>;
 222                         summit,fast-voltage-threshold-microvolt = <2600000>;
 223                         summit,chip-temperature-threshold-celsius = <130>;
 224                         summit,usb-current-limit-microamp = <1800000>;
 225
 226                         monitored-battery = <&battery_cell>;
 227                 };
 228         };
 229
 230         panel {
 231                 compatible = "samsung,ltl101al01";
 232                 pinctrl-0 = <&lvds_nshdn>;
 233                 pinctrl-names = "default";
 234                 power-supply = <&panel_vdd>;
 235                 enable-gpios = <&gpm0 5 GPIO_ACTIVE_HIGH>;
 236                 backlight = <&backlight>;
 237
 238                 port {
 239                         lcd_ep: endpoint {
 240                                 remote-endpoint = <&fimd_ep>;
 241                         };
 242                 };
 243         };
 244
 245         backlight: backlight {
 246                 compatible = "pwm-backlight";
 247                 pinctrl-0 = <&led_bl_reset>;
 248                 pinctrl-names = "default";
 249                 enable-gpios = <&gpm0 1 GPIO_ACTIVE_HIGH>;
 250                 pwms = <&pwm 1 78770 0>;
 251                 brightness-levels = <0 48 128 255>;
 252                 num-interpolated-steps = <8>;
 253                 default-brightness-level = <12>;
 254         };
 255 };
 256
 257 &adc {
 258         vdd-supply = <&ldo3_reg>;
 259         /* not verified */
 260         status = "okay";
 261 };
 262
 263 &bus_dmc {
 264         devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>;
 265         vdd-supply = <&buck1_reg>;
 266         status = "okay";
 267 };
 268
 269 &bus_acp {
 270         devfreq = <&bus_dmc>;
 271         status = "okay";
 272 };
 273
 274 &bus_c2c {
 275         devfreq = <&bus_dmc>;
 276         status = "okay";
 277 };
 278
 279 &bus_leftbus {
 280         devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>;
 281         vdd-supply = <&buck3_reg>;
 282         status = "okay";
 283 };
 284
 285 &bus_rightbus {
 286         devfreq = <&bus_leftbus>;
 287         status = "okay";
 288 };
 289
 290 &bus_display {
 291         devfreq = <&bus_leftbus>;
 292         status = "okay";
 293 };
 294
 295 &bus_fsys {
 296         devfreq = <&bus_leftbus>;
 297         status = "okay";
 298 };
 299
 300 &bus_peri {
 301         devfreq = <&bus_leftbus>;
 302         status = "okay";
 303 };
 304
 305 &bus_mfc {
 306         devfreq = <&bus_leftbus>;
 307         status = "okay";
 308 };
 309
 310 &cpu0 {
 311         cpu0-supply = <&buck2_reg>;
 312 };
 313
 314 &cpu_thermal {
 315         cooling-maps {
 316                 map0 {
 317                         /* Corresponds to 800MHz at freq_table */
 318                         cooling-device = <&cpu0 7 7>, <&cpu1 7 7>,
 319                                          <&cpu2 7 7>, <&cpu3 7 7>;
 320                 };
 321                 map1 {
 322                         /* Corresponds to 200MHz at freq_table */
 323                         cooling-device = <&cpu0 13 13>, <&cpu1 13 13>,
 324                                          <&cpu2 13 13>, <&cpu3 13 13>;
 325                 };
 326         };
 327 };
 328
 329 &exynos_usbphy {
 330         status = "okay";
 331 };
 332
 333 &fimd {
 334         pinctrl-0 = <&lcd_clk &lcd_data24>;
 335         pinctrl-names = "default";
 336         #address-cells = <1>;
 337         #size-cells = <0>;
 338         status = "okay";
 339
 340         samsung,invert-vclk;
 341
 342         port@3 {
 343                 reg = <3>;
 344
 345                 fimd_ep: endpoint {
 346                         remote-endpoint = <&lcd_ep>;
 347                 };
 348         };
 349 };
 350
 351 &gpu {
 352         mali-supply = <&buck4_reg>;
 353         status = "okay";
 354 };
 355
 356 &hsotg {
 357         vusb_a-supply = <&ldo12_reg>;
 358         dr_mode = "peripheral";
 359         status = "okay";
 360 };
 361
 362 &i2c_3 {
 363         samsung,i2c-sda-delay = <100>;
 364         samsung,i2c-slave-addr = <0x10>;
 365         samsung,i2c-max-bus-freq = <400000>;
 366         pinctrl-0 = <&i2c3_bus>;
 367         pinctrl-names = "default";
 368         status = "okay";
 369
 370         touchscreen@4a {
 371                 compatible = "atmel,maxtouch";
 372                 reg = <0x4a>;
 373                 pinctrl-0 = <&tsp_rst &tsp_irq>;
 374                 pinctrl-names = "default";
 375                 interrupt-parent = <&gpm2>;
 376                 interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 377                 reset-gpios = <&gpm0 4 GPIO_ACTIVE_LOW>;
 378         };
 379 };
 380
 381 &i2c_7 {
 382         samsung,i2c-sda-delay = <100>;
 383         samsung,i2c-slave-addr = <0x10>;
 384         samsung,i2c-max-bus-freq = <400000>;
 385         pinctrl-0 = <&i2c7_bus>;
 386         pinctrl-names = "default";
 387         status = "okay";
 388
 389         max77686: pmic@9 {
 390                 compatible = "maxim,max77686";
 391                 interrupt-parent = <&gpx0>;
 392                 interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
 393                 pinctrl-0 = <&max77686_irq>;
 394                 pinctrl-names = "default";
 395                 wakeup-source;
 396                 reg = <0x09>;
 397                 #clock-cells = <1>;
 398
 399                 voltage-regulators {
 400                         ldo1_reg: LDO1 {
 401                                 regulator-name = "ldo1";
 402                                 regulator-always-on;
 403                         };
 404
 405                         ldo2_reg: LDO2 {
 406                                 regulator-name = "ldo2";
 407                                 regulator-always-on;
 408                         };
 409
 410                         /* WM8994 audio */
 411                         ldo3_reg: LDO3 {
 412                                 regulator-name = "VCC_1.8V_AP";
 413                                 regulator-min-microvolt = <1800000>;
 414                                 regulator-max-microvolt = <1800000>;
 415                                 regulator-always-on;
 416                                 regulator-boot-on;
 417
 418                                 regulator-state-mem {
 419                                         regulator-on-in-suspend;
 420                                 };
 421                         };
 422
 423                         ldo4_reg: LDO4 {
 424                                 regulator-name = "ldo4";
 425                                 regulator-always-on;
 426                         };
 427
 428                         ldo5_reg: LDO5 {
 429                                 regulator-name = "VCC_1.8V_IO";
 430                                 regulator-min-microvolt = <1800000>;
 431                                 regulator-max-microvolt = <1800000>;
 432
 433                                 regulator-state-mem {
 434                                         regulator-off-in-suspend;
 435                                 };
 436                         };
 437
 438                         ldo6_reg: LDO6 {
 439                                 regulator-name = "ldo6";
 440                                 regulator-always-on;
 441                         };
 442
 443                         ldo7_reg: LDO7 {
 444                                 regulator-name = "ldo7";
 445                                 regulator-always-on;
 446                         };
 447
 448                         /* CSI IP block */
 449                         ldo8_reg: LDO8 {
 450                                 regulator-name = "VMIPI_1.0V";
 451                                 regulator-min-microvolt = <1000000>;
 452                                 regulator-max-microvolt = <1000000>;
 453                                 regulator-always-on;
 454                                 regulator-boot-on;
 455
 456                                 regulator-state-mem {
 457                                         regulator-on-in-suspend;
 458                                 };
 459                         };
 460
 461                         /* IR LED on/off */
 462                         ldo9_reg: LDO9 {
 463                                 regulator-name = "VLED_IC_1.9V";
 464                                 regulator-min-microvolt = <1950000>;
 465                                 regulator-max-microvolt = <1950000>;
 466
 467                                 regulator-state-mem {
 468                                         regulator-off-in-suspend;
 469                                 };
 470                         };
 471
 472                         /* CSI IP block */
 473                         ldo10_reg: LDO10 {
 474                                 regulator-name = "VMIPI_1.8V";
 475                                 regulator-min-microvolt = <1800000>;
 476                                 regulator-max-microvolt = <1800000>;
 477                                 regulator-always-on;
 478                                 regulator-boot-on;
 479
 480                                 regulator-state-mem {
 481                                         regulator-on-in-suspend;
 482                                 };
 483                         };
 484
 485                         ldo11_reg: LDO11 {
 486                                 regulator-name = "VABB1_1.9V";
 487                                 regulator-min-microvolt = <1950000>;
 488                                 regulator-max-microvolt = <1950000>;
 489                                 regulator-always-on;
 490                                 regulator-boot-on;
 491
 492                                 regulator-state-mem {
 493                                         regulator-off-in-suspend;
 494                                 };
 495                         };
 496
 497                         /* USB OTG */
 498                         ldo12_reg: LDO12 {
 499                                 regulator-name = "VUOTG_3.0V";
 500                                 regulator-min-microvolt = <3000000>;
 501                                 regulator-max-microvolt = <3000000>;
 502                                 regulator-always-on;
 503                                 regulator-boot-on;
 504
 505                                 regulator-state-mem {
 506                                         regulator-on-in-suspend;
 507                                 };
 508                         };
 509
 510                         /* not connected */
 511                         ldo13_reg: LDO13 {
 512                                 regulator-name = "ldo13";
 513                         };
 514
 515                         ldo14_reg: LDO14 {
 516                                 regulator-name = "VABB2_1.9V";
 517                                 regulator-min-microvolt = <1950000>;
 518                                 regulator-max-microvolt = <1950000>;
 519                                 regulator-always-on;
 520                                 regulator-boot-on;
 521
 522                                 regulator-state-mem {
 523                                         regulator-off-in-suspend;
 524                                 };
 525                         };
 526
 527                         ldo15_reg: LDO15 {
 528                                 regulator-name = "ldo15";
 529                                 regulator-always-on;
 530                         };
 531
 532                         ldo16_reg: LDO16 {
 533                                 regulator-name = "ldo16";
 534                                 regulator-always-on;
 535                         };
 536
 537                         /* not connected */
 538                         ldo17_reg: LDO17 {
 539                                 regulator-name = "ldo17";
 540                         };
 541
 542                         /* Camera ISX012 */
 543                         ldo18_reg: LDO18 {
 544                                 regulator-name = "CAM_IO_1.8V";
 545                                 regulator-min-microvolt = <1800000>;
 546                                 regulator-max-microvolt = <1800000>;
 547
 548                                 regulator-state-mem {
 549                                         regulator-off-in-suspend;
 550                                 };
 551                         };
 552
 553                         /* Camera S5K6A3 */
 554                         ldo19_reg: LDO19 {
 555                                 regulator-name = "VT_CORE_1.8V";
 556                                 regulator-min-microvolt = <1800000>;
 557                                 regulator-max-microvolt = <1800000>;
 558
 559                                 regulator-state-mem {
 560                                         regulator-off-in-suspend;
 561                                 };
 562                         };
 563
 564                         /* not connected */
 565                         ldo20_reg: LDO20 {
 566                                 regulator-name = "ldo20";
 567                         };
 568
 569                         /* MMC2 */
 570                         ldo21_reg: LDO21 {
 571                                 regulator-name = "VTF_2.8V";
 572                                 regulator-min-microvolt = <2800000>;
 573                                 regulator-max-microvolt = <2800000>;
 574                                 maxim,ena-gpios = <&gpy2 0 GPIO_ACTIVE_HIGH>;
 575                         };
 576
 577                         /* not connected */
 578                         ldo22_reg: LDO22 {
 579                                 regulator-name = "ldo22";
 580                         };
 581
 582                         /* ADC */
 583                         ldo23_reg: LDO23 {
 584                                 regulator-name = "VDD_ADC_3.3V";
 585                                 regulator-min-microvolt = <3300000>;
 586                                 regulator-max-microvolt = <3300000>;
 587                                 regulator-always-on;
 588                                 regulator-boot-on;
 589
 590                                 regulator-state-mem {
 591                                         regulator-off-in-suspend;
 592                                 };
 593                         };
 594
 595                         /* Camera S5K6A3 */
 596                         ldo24_reg: LDO24 {
 597                                 regulator-name = "CAM_A2.8V";
 598                                 regulator-min-microvolt = <2800000>;
 599                                 regulator-max-microvolt = <2800000>;
 600
 601                                 regulator-state-mem {
 602                                         regulator-off-in-suspend;
 603                                 };
 604                         };
 605
 606                         ldo25_reg: LDO25 {
 607                                 regulator-name = "VLED_3.3V";
 608                                 regulator-min-microvolt = <3300000>;
 609                                 regulator-max-microvolt = <3300000>;
 610
 611                                 regulator-state-mem {
 612                                         regulator-off-in-suspend;
 613                                 };
 614                         };
 615
 616                         /* Camera ISX012 */
 617                         ldo26_reg: LDO26 {
 618                                 regulator-name = "3MP_AF_2.8V";
 619                                 regulator-min-microvolt = <2800000>;
 620                                 regulator-max-microvolt = <2800000>;
 621
 622                                 regulator-state-mem {
 623                                         regulator-off-in-suspend;
 624                                 };
 625                         };
 626
 627                         buck1_reg: BUCK1 {
 628                                 regulator-name = "VDD_MIF";
 629                                 regulator-min-microvolt = <850000>;
 630                                 regulator-max-microvolt = <1050000>;
 631                                 regulator-always-on;
 632                                 regulator-boot-on;
 633                         };
 634
 635                         buck2_reg: BUCK2 {
 636                                 regulator-name = "VDD_ARM";
 637                                 regulator-min-microvolt = <850000>;
 638                                 regulator-max-microvolt = <1500000>;
 639                                 regulator-always-on;
 640                                 regulator-boot-on;
 641                         };
 642
 643                         buck3_reg: BUCK3 {
 644                                 regulator-name = "VDD_INT";
 645                                 regulator-min-microvolt = <850000>;
 646                                 regulator-max-microvolt = <1100000>;
 647                                 regulator-always-on;
 648                                 regulator-boot-on;
 649                         };
 650
 651                         buck4_reg: BUCK4 {
 652                                 regulator-name = "VDD_G3D";
 653                                 regulator-min-microvolt = <850000>;
 654                                 regulator-max-microvolt = <1075000>;
 655                                 regulator-boot-on;
 656                         };
 657
 658                         buck5_reg: BUCK5 {
 659                                 regulator-name = "buck5";
 660                                 regulator-always-on;
 661                         };
 662
 663                         buck6_reg: BUCK6 {
 664                                 regulator-name = "buck6";
 665                                 regulator-always-on;
 666                         };
 667
 668                         buck7_reg: BUCK7 {
 669                                 regulator-name = "buck7";
 670                                 regulator-always-on;
 671                         };
 672
 673                         /* not connected */
 674                         buck8_reg: BUCK8 {
 675                                 regulator-name = "buck8";
 676                         };
 677
 678                         buck9_reg: BUCK9 {
 679                                 regulator-name = "3MP_CORE_1.2V";
 680                                 regulator-min-microvolt = <1200000>;
 681                                 regulator-max-microvolt = <1200000>;
 682
 683                                 regulator-state-mem {
 684                                         regulator-off-in-suspend;
 685                                 };
 686                         };
 687                 };
 688         };
 689 };
 690
 691 &mshc_0 {
 692         broken-cd;
 693         non-removable;
 694         card-detect-delay = <200>;
 695         clock-frequency = <400000000>;
 696         samsung,dw-mshc-ciu-div = <0>;
 697         samsung,dw-mshc-sdr-timing = <2 3>;
 698         samsung,dw-mshc-ddr-timing = <1 2>;
 699         pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
 700         pinctrl-names = "default";
 701         bus-width = <4>;
 702         cap-mmc-highspeed;
 703         cap-sd-highspeed;
 704         status = "okay";
 705 };
 706
 707 &pinctrl_0 {
 708         pinctrl-names = "default";
 709         pinctrl-0 = <&sleep0>;
 710
 711         tsp_reg_gpio_2: tsp-reg-gpio-2-pins {
 712                 samsung,pins = "gpb-5";
 713                 samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 714                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 715         };
 716
 717         tsp_reg_gpio_3: tsp-reg-gpio-3-pins {
 718                 samsung,pins = "gpb-7";
 719                 samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 720                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 721         };
 722
 723         lcd_enable: lcd-enable-pins {
 724                 samsung,pins = "gpc0-1";
 725                 samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 726                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 727         };
 728
 729         sleep0: sleep-state {
 730                 PIN_SLP(gpa0-0, INPUT, NONE);
 731                 PIN_SLP(gpa0-1, OUT0, NONE);
 732                 PIN_SLP(gpa0-2, INPUT, NONE);
 733                 PIN_SLP(gpa0-3, INPUT, UP);
 734                 PIN_SLP(gpa0-4, INPUT, NONE);
 735                 PIN_SLP(gpa0-5, INPUT, DOWN);
 736                 PIN_SLP(gpa0-6, INPUT, DOWN);
 737                 PIN_SLP(gpa0-7, INPUT, UP);
 738
 739                 PIN_SLP(gpa1-0, INPUT, DOWN);
 740                 PIN_SLP(gpa1-1, INPUT, DOWN);
 741                 PIN_SLP(gpa1-2, INPUT, DOWN);
 742                 PIN_SLP(gpa1-3, INPUT, DOWN);
 743                 PIN_SLP(gpa1-4, INPUT, DOWN);
 744                 PIN_SLP(gpa1-5, INPUT, DOWN);
 745
 746                 PIN_SLP(gpb-0, INPUT, NONE);
 747                 PIN_SLP(gpb-1, INPUT, NONE);
 748                 PIN_SLP(gpb-2, INPUT, NONE);
 749                 PIN_SLP(gpb-3, INPUT, NONE);
 750                 PIN_SLP(gpb-4, INPUT, DOWN);
 751                 PIN_SLP(gpb-5, INPUT, DOWN);
 752                 PIN_SLP(gpb-6, INPUT, DOWN);
 753                 PIN_SLP(gpb-7, INPUT, DOWN);
 754
 755                 PIN_SLP(gpc0-0, INPUT, DOWN);
 756                 PIN_SLP(gpc0-1, INPUT, DOWN);
 757                 PIN_SLP(gpc0-2, INPUT, DOWN);
 758                 PIN_SLP(gpc0-3, INPUT, DOWN);
 759                 PIN_SLP(gpc0-4, INPUT, DOWN);
 760
 761                 PIN_SLP(gpc1-0, INPUT, UP);
 762                 PIN_SLP(gpc1-1, PREV, NONE);
 763                 PIN_SLP(gpc1-2, INPUT, UP);
 764                 PIN_SLP(gpc1-3, INPUT, UP);
 765                 PIN_SLP(gpc1-4, INPUT, UP);
 766
 767                 PIN_SLP(gpd0-0, INPUT, DOWN);
 768                 PIN_SLP(gpd0-1, OUT0, NONE);
 769                 PIN_SLP(gpd0-2, INPUT, NONE);
 770                 PIN_SLP(gpd0-3, INPUT, NONE);
 771
 772                 PIN_SLP(gpd1-0, INPUT, DOWN);
 773                 PIN_SLP(gpd1-1, INPUT, DOWN);
 774                 PIN_SLP(gpd1-2, INPUT, NONE);
 775                 PIN_SLP(gpd1-3, INPUT, NONE);
 776
 777                 PIN_SLP(gpf0-0, OUT0, NONE);
 778                 PIN_SLP(gpf0-1, OUT0, NONE);
 779                 PIN_SLP(gpf0-2, OUT0, NONE);
 780                 PIN_SLP(gpf0-3, OUT0, NONE);
 781                 PIN_SLP(gpf0-4, OUT0, NONE);
 782                 PIN_SLP(gpf0-5, OUT0, NONE);
 783                 PIN_SLP(gpf0-6, OUT0, NONE);
 784                 PIN_SLP(gpf0-7, OUT0, NONE);
 785
 786                 PIN_SLP(gpf1-0, OUT0, NONE);
 787                 PIN_SLP(gpf1-1, OUT0, NONE);
 788                 PIN_SLP(gpf1-2, OUT0, NONE);
 789                 PIN_SLP(gpf1-3, OUT0, NONE);
 790                 PIN_SLP(gpf1-4, OUT0, NONE);
 791                 PIN_SLP(gpf1-5, OUT0, NONE);
 792                 PIN_SLP(gpf1-6, OUT0, NONE);
 793                 PIN_SLP(gpf1-7, OUT0, NONE);
 794
 795                 PIN_SLP(gpf2-0, OUT0, NONE);
 796                 PIN_SLP(gpf2-1, OUT0, NONE);
 797                 PIN_SLP(gpf2-2, OUT0, NONE);
 798                 PIN_SLP(gpf2-3, OUT0, NONE);
 799                 PIN_SLP(gpf2-4, OUT0, NONE);
 800                 PIN_SLP(gpf2-5, OUT0, NONE);
 801                 PIN_SLP(gpf2-6, OUT0, NONE);
 802                 PIN_SLP(gpf2-7, OUT0, NONE);
 803
 804                 PIN_SLP(gpf3-0, OUT0, NONE);
 805                 PIN_SLP(gpf3-1, OUT0, NONE);
 806                 PIN_SLP(gpf3-2, OUT0, NONE);
 807                 PIN_SLP(gpf3-3, OUT0, NONE);
 808                 PIN_SLP(gpf3-4, OUT0, NONE);
 809                 PIN_SLP(gpf3-5, OUT0, NONE);
 810
 811                 PIN_SLP(gpj0-0, INPUT, DOWN);
 812                 PIN_SLP(gpj0-1, INPUT, DOWN);
 813                 PIN_SLP(gpj0-2, INPUT, DOWN);
 814                 PIN_SLP(gpj0-3, PREV, NONE);
 815                 PIN_SLP(gpj0-4, PREV, NONE);
 816                 PIN_SLP(gpj0-5, OUT0, NONE);
 817                 PIN_SLP(gpj0-6, OUT0, NONE);
 818                 PIN_SLP(gpj0-7, OUT0, NONE);
 819
 820                 PIN_SLP(gpj1-0, OUT0, NONE);
 821                 PIN_SLP(gpj1-1, INPUT, DOWN);
 822                 PIN_SLP(gpj1-2, PREV, NONE);
 823                 PIN_SLP(gpj1-3, OUT0, NONE);
 824         };
 825 };
 826
 827 &pinctrl_1 {
 828         pinctrl-names = "default";
 829         pinctrl-0 = <&sleep1>;
 830
 831         sd3_wifi: sd3-wifi-pins {
 832                 samsung,pins = "gpk3-3", "gpk3-4", "gpk3-5", "gpk3-6";
 833                 samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 834                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 835         };
 836
 837         bt_shutdown: bt-shutdown-pins {
 838                 samsung,pins = "gpl0-6";
 839                 samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 840                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 841         };
 842
 843         uart_sel: uart-sel-pins {
 844                 samsung,pins = "gpl2-7";
 845                 samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 846                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 847                 samsung,pin-val = <1>;
 848                 /* 0 = CP, 1 = AP (serial output) */
 849         };
 850
 851         led_bl_reset: led-bl-reset-pins {
 852                 samsung,pins = "gpm0-1";
 853                 samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 854                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 855         };
 856
 857         tsp_rst: tsp-rst-pins {
 858                 samsung,pins = "gpm0-4";
 859                 samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 860                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 861         };
 862
 863         lvds_nshdn: lvds-nshdn-pins {
 864                 samsung,pins = "gpm0-5";
 865                 samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 866                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 867         };
 868
 869         tsp_irq: tsp-irq-pins {
 870                 samsung,pins = "gpm2-3";
 871                 samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 872                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 873         };
 874
 875         wifi_reset: wifi-reset-pins {
 876                 samsung,pins = "gpm3-5";
 877                 samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 878                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 879         };
 880
 881         tsp_reg_gpio_1: tsp-reg-gpio-1-pins {
 882                 samsung,pins = "gpm4-5";
 883                 samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 884                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 885         };
 886
 887         ak8975_irq: ak8975-irq-pins {
 888                 samsung,pins = "gpm4-7";
 889                 samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 890                 samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 891         };
 892
 893         stmpe_adc_irq: stmpe-adc-irq-pins {
 894                 samsung,pins = "gpx0-1";
 895                 samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 896                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 897         };
 898
 899         max77686_irq: max77686-irq-pins {
 900                 samsung,pins = "gpx0-7";
 901                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 902         };
 903
 904         gpio_keys: gpio-keys-pins {
 905                 samsung,pins = "gpx2-2", "gpx2-7", "gpx3-3";
 906                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 907         };
 908
 909         fuel_alert_irq: fuel-alert-irq-pins {
 910                 samsung,pins = "gpx2-3";
 911                 samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 912                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 913         };
 914
 915         wifi_host_wake: wifi-host-wake-pins {
 916                 samsung,pins = "gpx2-5";
 917                 samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
 918                 samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
 919         };
 920
 921         bt_host_wakeup: bt-host-wakeup-pins {
 922                 samsung,pins = "gpx2-6";
 923                 samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
 924                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 925         };
 926
 927         bt_device_wakeup: bt-device-wakeup-pins {
 928                 samsung,pins = "gpx3-1";
 929                 samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
 930                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 931         };
 932
 933         sdhci2_cd: sdhci2-cd-pins {
 934                 samsung,pins = "gpx3-4";
 935                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 936         };
 937
 938         sleep1: sleep-state {
 939                 PIN_SLP(gpk0-0, PREV, NONE);
 940                 PIN_SLP(gpk0-1, PREV, NONE);
 941                 PIN_SLP(gpk0-2, PREV, NONE);
 942                 PIN_SLP(gpk0-3, PREV, NONE);
 943                 PIN_SLP(gpk0-4, PREV, NONE);
 944                 PIN_SLP(gpk0-5, PREV, NONE);
 945                 PIN_SLP(gpk0-6, PREV, NONE);
 946
 947                 PIN_SLP(gpk1-0, INPUT, DOWN);
 948                 PIN_SLP(gpk1-1, INPUT, DOWN);
 949                 PIN_SLP(gpk1-2, INPUT, DOWN);
 950                 PIN_SLP(gpk1-3, PREV, NONE);
 951                 PIN_SLP(gpk1-4, PREV, NONE);
 952                 PIN_SLP(gpk1-5, PREV, NONE);
 953                 PIN_SLP(gpk1-6, PREV, NONE);
 954
 955                 PIN_SLP(gpk2-0, INPUT, DOWN);
 956                 PIN_SLP(gpk2-1, INPUT, DOWN);
 957                 PIN_SLP(gpk2-2, INPUT, DOWN);
 958                 PIN_SLP(gpk2-3, INPUT, DOWN);
 959                 PIN_SLP(gpk2-4, INPUT, DOWN);
 960                 PIN_SLP(gpk2-5, INPUT, DOWN);
 961                 PIN_SLP(gpk2-6, INPUT, DOWN);
 962
 963                 PIN_SLP(gpk3-0, OUT0, NONE);
 964                 PIN_SLP(gpk3-1, INPUT, NONE);
 965                 PIN_SLP(gpk3-2, INPUT, DOWN);
 966                 PIN_SLP(gpk3-3, INPUT, NONE);
 967                 PIN_SLP(gpk3-4, INPUT, NONE);
 968                 PIN_SLP(gpk3-5, INPUT, NONE);
 969                 PIN_SLP(gpk3-6, INPUT, NONE);
 970
 971                 PIN_SLP(gpl0-0, OUT0, NONE);
 972                 PIN_SLP(gpl0-1, INPUT, NONE);
 973                 PIN_SLP(gpl0-2, INPUT, NONE);
 974                 PIN_SLP(gpl0-3, INPUT, DOWN);
 975                 PIN_SLP(gpl0-4, PREV, NONE);
 976                 PIN_SLP(gpl0-6, PREV, NONE);
 977
 978                 PIN_SLP(gpl1-0, OUT0, NONE);
 979                 PIN_SLP(gpl1-1, OUT0, NONE);
 980
 981                 PIN_SLP(gpl2-0, INPUT, DOWN);
 982                 PIN_SLP(gpl2-1, INPUT, DOWN);
 983                 PIN_SLP(gpl2-2, INPUT, DOWN);
 984                 PIN_SLP(gpl2-3, INPUT, DOWN);
 985                 PIN_SLP(gpl2-4, OUT0, NONE);
 986                 PIN_SLP(gpl2-5, INPUT, DOWN);
 987                 PIN_SLP(gpl2-6, PREV, NONE);
 988                 PIN_SLP(gpl2-7, PREV, NONE);
 989
 990                 PIN_SLP(gpm0-0, PREV, NONE);
 991                 PIN_SLP(gpm0-1, OUT0, NONE);
 992                 PIN_SLP(gpm0-2, INPUT, DOWN);
 993                 PIN_SLP(gpm0-3, INPUT, NONE);
 994                 PIN_SLP(gpm0-4, OUT0, NONE);
 995                 PIN_SLP(gpm0-5, OUT0, NONE);
 996                 PIN_SLP(gpm0-6, INPUT, DOWN);
 997                 PIN_SLP(gpm0-7, OUT0, NONE);
 998
 999                 PIN_SLP(gpm1-0, INPUT, NONE);
1000                 PIN_SLP(gpm1-1, INPUT, NONE);
1001                 PIN_SLP(gpm1-2, INPUT, NONE);
1002                 PIN_SLP(gpm1-3, INPUT, NONE);
1003                 PIN_SLP(gpm1-4, INPUT, NONE);
1004                 PIN_SLP(gpm1-5, INPUT, NONE);
1005                 PIN_SLP(gpm1-6, INPUT, DOWN);
1006
1007                 PIN_SLP(gpm2-0, INPUT, NONE);
1008                 PIN_SLP(gpm2-1, INPUT, NONE);
1009                 PIN_SLP(gpm2-2, OUT0, NONE);
1010                 PIN_SLP(gpm2-3, OUT0, DOWN);
1011                 PIN_SLP(gpm2-4, INPUT, DOWN);
1012
1013                 PIN_SLP(gpm3-0, PREV, NONE);
1014                 PIN_SLP(gpm3-1, PREV, NONE);
1015                 PIN_SLP(gpm3-2, PREV, NONE);
1016                 PIN_SLP(gpm3-3, OUT1, NONE);
1017                 PIN_SLP(gpm3-4, OUT0, DOWN);
1018                 PIN_SLP(gpm3-5, PREV, NONE);
1019                 PIN_SLP(gpm3-6, PREV, NONE);
1020                 PIN_SLP(gpm3-7, OUT0, NONE);
1021
1022                 PIN_SLP(gpm4-0, INPUT, NONE);
1023                 PIN_SLP(gpm4-1, INPUT, NONE);
1024                 PIN_SLP(gpm4-2, INPUT, DOWN);
1025                 PIN_SLP(gpm4-3, INPUT, DOWN);
1026                 PIN_SLP(gpm4-4, PREV, NONE);
1027                 PIN_SLP(gpm4-5, OUT0, NONE);
1028                 PIN_SLP(gpm4-6, OUT0, NONE);
1029                 PIN_SLP(gpm4-7, INPUT, DOWN);
1030
1031                 PIN_SLP(gpy0-0, INPUT, DOWN);
1032                 PIN_SLP(gpy0-1, INPUT, DOWN);
1033                 PIN_SLP(gpy0-2, INPUT, NONE);
1034                 PIN_SLP(gpy0-3, INPUT, NONE);
1035                 PIN_SLP(gpy0-4, INPUT, NONE);
1036                 PIN_SLP(gpy0-5, INPUT, NONE);
1037
1038                 PIN_SLP(gpy1-0, INPUT, DOWN);
1039                 PIN_SLP(gpy1-1, INPUT, DOWN);
1040                 PIN_SLP(gpy1-2, INPUT, DOWN);
1041                 PIN_SLP(gpy1-3, INPUT, DOWN);
1042
1043                 PIN_SLP(gpy2-0, PREV, NONE);
1044                 PIN_SLP(gpy2-1, INPUT, DOWN);
1045                 PIN_SLP(gpy2-2, INPUT, NONE);
1046                 PIN_SLP(gpy2-3, INPUT, NONE);
1047                 PIN_SLP(gpy2-4, INPUT, NONE);
1048                 PIN_SLP(gpy2-5, INPUT, NONE);
1049
1050                 PIN_SLP(gpy3-0, INPUT, DOWN);
1051                 PIN_SLP(gpy3-1, INPUT, DOWN);
1052                 PIN_SLP(gpy3-2, INPUT, DOWN);
1053                 PIN_SLP(gpy3-3, INPUT, DOWN);
1054                 PIN_SLP(gpy3-4, INPUT, DOWN);
1055                 PIN_SLP(gpy3-5, INPUT, DOWN);
1056                 PIN_SLP(gpy3-6, INPUT, DOWN);
1057                 PIN_SLP(gpy3-7, INPUT, DOWN);
1058
1059                 PIN_SLP(gpy4-0, INPUT, DOWN);
1060                 PIN_SLP(gpy4-1, INPUT, DOWN);
1061                 PIN_SLP(gpy4-2, INPUT, DOWN);
1062                 PIN_SLP(gpy4-3, INPUT, DOWN);
1063                 PIN_SLP(gpy4-4, INPUT, DOWN);
1064                 PIN_SLP(gpy4-5, INPUT, DOWN);
1065                 PIN_SLP(gpy4-6, INPUT, DOWN);
1066                 PIN_SLP(gpy4-7, INPUT, DOWN);
1067
1068                 PIN_SLP(gpy5-0, INPUT, DOWN);
1069                 PIN_SLP(gpy5-1, INPUT, DOWN);
1070                 PIN_SLP(gpy5-2, INPUT, DOWN);
1071                 PIN_SLP(gpy5-3, INPUT, DOWN);
1072                 PIN_SLP(gpy5-4, INPUT, DOWN);
1073                 PIN_SLP(gpy5-5, INPUT, DOWN);
1074                 PIN_SLP(gpy5-6, INPUT, DOWN);
1075                 PIN_SLP(gpy5-7, INPUT, DOWN);
1076
1077                 PIN_SLP(gpy6-0, INPUT, DOWN);
1078                 PIN_SLP(gpy6-1, INPUT, DOWN);
1079                 PIN_SLP(gpy6-2, INPUT, DOWN);
1080                 PIN_SLP(gpy6-3, INPUT, DOWN);
1081                 PIN_SLP(gpy6-4, INPUT, DOWN);
1082                 PIN_SLP(gpy6-5, INPUT, DOWN);
1083                 PIN_SLP(gpy6-6, INPUT, DOWN);
1084                 PIN_SLP(gpy6-7, INPUT, DOWN);
1085         };
1086 };
1087
1088 &pinctrl_2 {
1089         pinctrl-names = "default";
1090         pinctrl-0 = <&sleep2>;
1091
1092         sleep2: sleep-state {
1093                 PIN_SLP(gpz-0, INPUT, DOWN);
1094                 PIN_SLP(gpz-1, INPUT, DOWN);
1095                 PIN_SLP(gpz-2, INPUT, DOWN);
1096                 PIN_SLP(gpz-3, INPUT, DOWN);
1097                 PIN_SLP(gpz-4, INPUT, DOWN);
1098                 PIN_SLP(gpz-5, INPUT, DOWN);
1099                 PIN_SLP(gpz-6, INPUT, DOWN);
1100         };
1101 };
1102
1103 &pinctrl_3 {
1104         pinctrl-names = "default";
1105         pinctrl-0 = <&sleep3>;
1106
1107         sleep3: sleep-state {
1108                 PIN_SLP(gpv0-0, INPUT, DOWN);
1109                 PIN_SLP(gpv0-1, INPUT, DOWN);
1110                 PIN_SLP(gpv0-2, INPUT, DOWN);
1111                 PIN_SLP(gpv0-3, INPUT, DOWN);
1112                 PIN_SLP(gpv0-4, INPUT, DOWN);
1113                 PIN_SLP(gpv0-5, INPUT, DOWN);
1114                 PIN_SLP(gpv0-6, INPUT, DOWN);
1115                 PIN_SLP(gpv0-7, INPUT, DOWN);
1116
1117                 PIN_SLP(gpv1-0, INPUT, DOWN);
1118                 PIN_SLP(gpv1-1, INPUT, DOWN);
1119                 PIN_SLP(gpv1-2, INPUT, DOWN);
1120                 PIN_SLP(gpv1-3, INPUT, DOWN);
1121                 PIN_SLP(gpv1-4, INPUT, DOWN);
1122                 PIN_SLP(gpv1-5, INPUT, DOWN);
1123                 PIN_SLP(gpv1-6, INPUT, DOWN);
1124                 PIN_SLP(gpv1-7, INPUT, DOWN);
1125
1126                 PIN_SLP(gpv2-0, INPUT, DOWN);
1127                 PIN_SLP(gpv2-1, INPUT, DOWN);
1128                 PIN_SLP(gpv2-2, INPUT, DOWN);
1129                 PIN_SLP(gpv2-3, INPUT, DOWN);
1130                 PIN_SLP(gpv2-4, INPUT, DOWN);
1131                 PIN_SLP(gpv2-5, INPUT, DOWN);
1132                 PIN_SLP(gpv2-6, INPUT, DOWN);
1133                 PIN_SLP(gpv2-7, INPUT, DOWN);
1134
1135                 PIN_SLP(gpv3-0, INPUT, DOWN);
1136                 PIN_SLP(gpv3-1, INPUT, DOWN);
1137                 PIN_SLP(gpv3-2, INPUT, DOWN);
1138                 PIN_SLP(gpv3-3, INPUT, DOWN);
1139                 PIN_SLP(gpv3-4, INPUT, DOWN);
1140                 PIN_SLP(gpv3-5, INPUT, DOWN);
1141                 PIN_SLP(gpv3-6, INPUT, DOWN);
1142                 PIN_SLP(gpv3-7, INPUT, DOWN);
1143
1144                 PIN_SLP(gpv4-0, INPUT, DOWN);
1145                 PIN_SLP(gpv4-1, INPUT, DOWN);
1146         };
1147 };
1148
1149 &pmu_system_controller {
1150         assigned-clocks = <&pmu_system_controller 0>;
1151         assigned-clock-parents = <&clock CLK_XUSBXTI>;
1152 };
1153
1154 &pwm {
1155         pinctrl-0 = <&pwm1_out>;
1156         pinctrl-names = "default";
1157         samsung,pwm-outputs = <1>;
1158         status = "okay";
1159 };
1160
1161 &rtc {
1162         clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>;
1163         clock-names = "rtc", "rtc_src";
1164         status = "okay";
1165 };
1166
1167 &sdhci_2 {
1168         bus-width = <4>;
1169         cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>;
1170         pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sdhci2_cd>;
1171         pinctrl-names = "default";
1172         vmmc-supply = <&ldo21_reg>;
1173         status = "okay";
1174 };
1175
1176 &sdhci_3 {
1177         #address-cells = <1>;
1178         #size-cells = <0>;
1179         non-removable;
1180         bus-width = <4>;
1181         mmc-pwrseq = <&wlan_pwrseq>;
1182
1183         pinctrl-names = "default";
1184         pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_wifi>;
1185         status = "okay";
1186
1187         wifi@1 {
1188                 compatible = "brcm,bcm4329-fmac";
1189                 reg = <0x1>;
1190                 pinctrl-names = "default";
1191                 pinctrl-0 = <&wifi_host_wake>;
1192                 interrupt-parent = <&gpx2>;
1193                 interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
1194                 interrupt-names = "host-wake";
1195         };
1196 };
1197
1198 &serial_0 {
1199         pinctrl-0 = <&uart0_data &uart0_fctl>;
1200         pinctrl-names = "default";
1201         status = "okay";
1202
1203         bluetooth {
1204                 compatible = "brcm,bcm4330-bt";
1205                 pinctrl-0 = <&bt_shutdown &bt_device_wakeup &bt_host_wakeup>;
1206                 pinctrl-names = "default";
1207
1208                 max-speed = <2000000>;
1209                 shutdown-gpios = <&gpl0 6 GPIO_ACTIVE_HIGH>;
1210                 device-wakeup-gpios = <&gpx3 1 GPIO_ACTIVE_HIGH>;
1211                 host-wakeup-gpios = <&gpx2 6 GPIO_ACTIVE_HIGH>;
1212                 clocks = <&max77686 MAX77686_CLK_PMIC>;
1213                 clock-names = "lpo";
1214         };
1215 };
1216
1217 &serial_2 {
1218         pinctrl-0 = <&uart_sel>;
1219         pinctrl-names = "default";
1220         status = "okay";
1221 };
1222
1223 &tmu {
1224         status = "okay";
1225 };