arch/arm/boot/dts/exynos4412-midas.dtsi

   1 // SPDX-License-Identifier: GPL-2.0
   2 /*
   3  * Samsung's Exynos4412 based Trats 2 board device tree source
   4  *
   5  * Copyright (c) 2013 Samsung Electronics Co., Ltd.
   6  *              http://www.samsung.com
   7  *
   8  * Device tree source file for Samsung's Trats 2 board which is based on
   9  * Samsung's Exynos4412 SoC.
  10  */
  11
  12 /dts-v1/;
  13 #include "exynos4412.dtsi"
  14 #include "exynos4412-ppmu-common.dtsi"
  15
  16 #include <dt-bindings/gpio/gpio.h>
  17 #include <dt-bindings/input/input.h>
  18 #include <dt-bindings/interrupt-controller/irq.h>
  19 #include <dt-bindings/clock/maxim,max77686.h>
  20 #include "exynos-pinctrl.h"
  21
  22 / {
  23         compatible = "samsung,midas", "samsung,exynos4412", "samsung,exynos4";
  24
  25         aliases {
  26                 i2c11 = &i2c_max77693;
  27                 i2c12 = &i2c_max77693_fuel;
  28         };
  29
  30         chosen {
  31                 stdout-path = &serial_2;
  32         };
  33
  34         firmware@204f000 {
  35                 compatible = "samsung,secure-firmware";
  36                 reg = <0x0204F000 0x1000>;
  37         };
  38
  39         fixed-rate-clocks {
  40                 xxti {
  41                         compatible = "samsung,clock-xxti";
  42                         clock-frequency = <0>;
  43                 };
  44
  45                 xusbxti {
  46                         compatible = "samsung,clock-xusbxti";
  47                         clock-frequency = <24000000>;
  48                 };
  49         };
  50
  51         cam_io_reg: voltage-regulator-1 {
  52                 compatible = "regulator-fixed";
  53                 regulator-name = "CAM_SENSOR_A";
  54                 regulator-min-microvolt = <2800000>;
  55                 regulator-max-microvolt = <2800000>;
  56                 enable-active-high;
  57                 status = "disabled";
  58         };
  59
  60         cam_af_reg: voltage-regulator-2 {
  61                 compatible = "regulator-fixed";
  62                 regulator-name = "CAM_AF";
  63                 regulator-min-microvolt = <2800000>;
  64                 regulator-max-microvolt = <2800000>;
  65                 enable-active-high;
  66                 status = "disabled";
  67         };
  68
  69         vsil12: voltage-regulator-3 {
  70                 compatible = "regulator-fixed";
  71                 regulator-name = "VSIL_1.2V";
  72                 regulator-min-microvolt = <1200000>;
  73                 regulator-max-microvolt = <1200000>;
  74                 gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>;
  75                 enable-active-high;
  76                 vin-supply = <&buck7_reg>;
  77         };
  78
  79         vcc33mhl: voltage-regulator-4 {
  80                 compatible = "regulator-fixed";
  81                 regulator-name = "VCC_3.3_MHL";
  82                 regulator-min-microvolt = <3300000>;
  83                 regulator-max-microvolt = <3300000>;
  84                 gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>;
  85                 enable-active-high;
  86         };
  87
  88         vcc18mhl: voltage-regulator-5 {
  89                 compatible = "regulator-fixed";
  90                 regulator-name = "VCC_1.8_MHL";
  91                 regulator-min-microvolt = <1800000>;
  92                 regulator-max-microvolt = <1800000>;
  93                 gpio = <&gpl0 4 GPIO_ACTIVE_HIGH>;
  94                 enable-active-high;
  95         };
  96
  97         touchkey_reg: voltage-regulator-6 {
  98                 compatible = "regulator-fixed";
  99                 regulator-name = "LED_VDD_3.3V";
 100                 regulator-min-microvolt = <3300000>;
 101                 regulator-max-microvolt = <3300000>;
 102                 enable-active-high;
 103                 status = "disabled";
 104         };
 105
 106         vbatt_reg: voltage-regulator-7 {
 107                 compatible = "regulator-fixed";
 108                 regulator-name = "VBATT";
 109                 regulator-min-microvolt = <5000000>;
 110                 regulator-max-microvolt = <5000000>;
 111                 regulator-always-on;
 112         };
 113
 114         mic_bias_reg: voltage-regulator-8 {
 115                 compatible = "regulator-fixed";
 116                 regulator-name = "MICBIAS_LDO_2.8V";
 117                 regulator-min-microvolt = <2800000>;
 118                 regulator-max-microvolt = <2800000>;
 119                 gpio = <&gpf1 7 GPIO_ACTIVE_HIGH>;
 120                 enable-active-high;
 121         };
 122
 123         submic_bias_reg: voltage-regulator-9 {
 124                 compatible = "regulator-fixed";
 125                 regulator-name = "SUB_MICBIAS_LDO_2.8V";
 126                 regulator-min-microvolt = <2800000>;
 127                 regulator-max-microvolt = <2800000>;
 128         };
 129
 130         gpio-keys {
 131                 compatible = "gpio-keys";
 132                 pinctrl-names = "default";
 133                 pinctrl-0 = <&gpio_keys>;
 134
 135                 key-down {
 136                         gpios = <&gpx3 3 GPIO_ACTIVE_LOW>;
 137                         linux,code = <114>;
 138                         label = "volume down";
 139                         debounce-interval = <10>;
 140                 };
 141
 142                 key-up {
 143                         gpios = <&gpx2 2 GPIO_ACTIVE_LOW>;
 144                         linux,code = <115>;
 145                         label = "volume up";
 146                         debounce-interval = <10>;
 147                 };
 148
 149                 key-power {
 150                         gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
 151                         linux,code = <116>;
 152                         label = "power";
 153                         debounce-interval = <10>;
 154                         wakeup-source;
 155                 };
 156
 157                 key-ok {
 158                         gpios = <&gpx0 1 GPIO_ACTIVE_LOW>;
 159                         linux,code = <139>;
 160                         label = "ok";
 161                         debounce-interval = <10>;
 162                         wakeup-source;
 163                 };
 164         };
 165
 166         i2c_max77693: i2c-gpio-1 {
 167                 compatible = "i2c-gpio";
 168                 sda-gpios = <&gpm2 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 169                 scl-gpios = <&gpm2 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 170                 i2c-gpio,delay-us = <2>;
 171                 #address-cells = <1>;
 172                 #size-cells = <0>;
 173
 174                 pmic@66 {
 175                         compatible = "maxim,max77693";
 176                         interrupt-parent = <&gpx1>;
 177                         interrupts = <5 IRQ_TYPE_LEVEL_LOW>;
 178                         pinctrl-names = "default";
 179                         pinctrl-0 = <&max77693_irq>;
 180                         reg = <0x66>;
 181
 182                         regulators {
 183                                 esafeout1_reg: ESAFEOUT1 {
 184                                         regulator-name = "ESAFEOUT1";
 185                                 };
 186                                 esafeout2_reg: ESAFEOUT2 {
 187                                         regulator-name = "ESAFEOUT2";
 188                                 };
 189                                 charger_reg: CHARGER {
 190                                         regulator-name = "CHARGER";
 191                                         regulator-min-microamp = <60000>;
 192                                         regulator-max-microamp = <2580000>;
 193                                 };
 194                         };
 195
 196                         motor-driver {
 197                                 compatible = "maxim,max77693-haptic";
 198                                 haptic-supply = <&ldo26_reg>;
 199                                 pwms = <&pwm 0 38022 0>;
 200                         };
 201
 202                         charger {
 203                                 compatible = "maxim,max77693-charger";
 204
 205                                 maxim,constant-microvolt = <4350000>;
 206                                 maxim,min-system-microvolt = <3600000>;
 207                                 maxim,thermal-regulation-celsius = <100>;
 208                                 maxim,battery-overcurrent-microamp = <3500000>;
 209                                 maxim,charge-input-threshold-microvolt = <4300000>;
 210                         };
 211                 };
 212         };
 213
 214         i2c_max77693_fuel: i2c-gpio-3 {
 215                 compatible = "i2c-gpio";
 216                 sda-gpios = <&gpf1 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 217                 scl-gpios = <&gpf1 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 218                 i2c-gpio,delay-us = <2>;
 219                 #address-cells = <1>;
 220                 #size-cells = <0>;
 221
 222                 fuel-gauge@36 {
 223                         compatible = "maxim,max17047";
 224                         interrupt-parent = <&gpx2>;
 225                         interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 226                         pinctrl-names = "default";
 227                         pinctrl-0 = <&max77693_fuel_irq>;
 228                         reg = <0x36>;
 229
 230                         maxim,over-heat-temp = <700>;
 231                         maxim,over-volt = <4500>;
 232                 };
 233         };
 234
 235         i2c-gpio-4 {
 236                 compatible = "i2c-gpio";
 237                 sda-gpios = <&gpl0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 238                 scl-gpios = <&gpl0 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 239                 i2c-gpio,delay-us = <2>;
 240                 #address-cells = <1>;
 241                 #size-cells = <0>;
 242
 243                 touchkey@20 {
 244                         compatible = "cypress,midas-touchkey";
 245                         reg = <0x20>;
 246                         vdd-supply = <&touchkey_reg>;
 247                         vcc-supply = <&ldo5_reg>;
 248                         interrupt-parent = <&gpj0>;
 249                         interrupts = <3 IRQ_TYPE_EDGE_FALLING>;
 250                         linux,keycodes = <KEY_BACK KEY_MENU>;
 251                 };
 252         };
 253
 254         i2c-mhl {
 255                 compatible = "i2c-gpio";
 256                 sda-gpios = <&gpf0 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 257                 scl-gpios = <&gpf0 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 258                 i2c-gpio,delay-us = <100>;
 259                 #address-cells = <1>;
 260                 #size-cells = <0>;
 261
 262                 pinctrl-0 = <&i2c_mhl_bus>;
 263                 pinctrl-names = "default";
 264
 265                 sii9234: hdmi-bridge@39 {
 266                         compatible = "sil,sii9234";
 267                         avcc33-supply = <&vcc33mhl>;
 268                         iovcc18-supply = <&vcc18mhl>;
 269                         avcc12-supply = <&vsil12>;
 270                         cvcc12-supply = <&vsil12>;
 271                         reset-gpios = <&gpf3 4 GPIO_ACTIVE_LOW>;
 272                         interrupt-parent = <&gpf3>;
 273                         interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
 274                         reg = <0x39>;
 275
 276                         port {
 277                                 mhl_to_hdmi: endpoint {
 278                                         remote-endpoint = <&hdmi_to_mhl>;
 279                                 };
 280                         };
 281                 };
 282         };
 283
 284         wlan_pwrseq: sdhci3-pwrseq {
 285                 compatible = "mmc-pwrseq-simple";
 286                 reset-gpios = <&gpj0 0 GPIO_ACTIVE_LOW>;
 287                 clocks = <&max77686 MAX77686_CLK_PMIC>;
 288                 clock-names = "ext_clock";
 289         };
 290
 291         sound: sound {
 292                 compatible = "samsung,midas-audio";
 293                 model = "Midas";
 294                 mic-bias-supply = <&mic_bias_reg>;
 295                 submic-bias-supply = <&submic_bias_reg>;
 296
 297                 cpu {
 298                         sound-dai = <&i2s0 0>;
 299                 };
 300                 codec {
 301                         sound-dai = <&wm1811>;
 302                 };
 303         };
 304
 305         thermistor-ap {
 306                 compatible = "murata,ncp15wb473";
 307                 pullup-uv = <1800000>;   /* VCC_1.8V_AP */
 308                 pullup-ohm = <100000>;   /* 100K */
 309                 pulldown-ohm = <100000>; /* 100K */
 310                 io-channels = <&adc 1>;  /* AP temperature */
 311         };
 312
 313         thermistor-battery {
 314                 compatible = "murata,ncp15wb473";
 315                 pullup-uv = <1800000>;   /* VCC_1.8V_AP */
 316                 pullup-ohm = <100000>;   /* 100K */
 317                 pulldown-ohm = <100000>; /* 100K */
 318                 io-channels = <&adc 2>;  /* Battery temperature */
 319         };
 320 };
 321
 322 &adc {
 323         vdd-supply = <&ldo3_reg>;
 324         status = "okay";
 325 };
 326
 327 &bus_dmc {
 328         devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>;
 329         vdd-supply = <&buck1_reg>;
 330         status = "okay";
 331 };
 332
 333 &bus_acp {
 334         devfreq = <&bus_dmc>;
 335         status = "okay";
 336 };
 337
 338 &bus_c2c {
 339         devfreq = <&bus_dmc>;
 340         status = "okay";
 341 };
 342
 343 &bus_leftbus {
 344         devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>;
 345         vdd-supply = <&buck3_reg>;
 346         status = "okay";
 347 };
 348
 349 &bus_rightbus {
 350         devfreq = <&bus_leftbus>;
 351         status = "okay";
 352 };
 353
 354 &bus_display {
 355         devfreq = <&bus_leftbus>;
 356         status = "okay";
 357 };
 358
 359 &bus_fsys {
 360         devfreq = <&bus_leftbus>;
 361         status = "okay";
 362 };
 363
 364 &bus_peri {
 365         devfreq = <&bus_leftbus>;
 366         status = "okay";
 367 };
 368
 369 &bus_mfc {
 370         devfreq = <&bus_leftbus>;
 371         status = "okay";
 372 };
 373
 374 &camera {
 375         pinctrl-0 = <&cam_port_a_clk_active &cam_port_b_clk_active>;
 376         pinctrl-names = "default";
 377         status = "okay";
 378         assigned-clocks = <&clock CLK_MOUT_CAM0>,
 379                 <&clock CLK_MOUT_CAM1>;
 380         assigned-clock-parents = <&clock CLK_XUSBXTI>,
 381                 <&clock CLK_XUSBXTI>;
 382 };
 383
 384 &cpu0 {
 385         cpu0-supply = <&buck2_reg>;
 386 };
 387
 388 &cpu_thermal {
 389         cooling-maps {
 390                 map0 {
 391                         /* Corresponds to 800MHz at freq_table */
 392                         cooling-device = <&cpu0 7 7>, <&cpu1 7 7>,
 393                                          <&cpu2 7 7>, <&cpu3 7 7>;
 394                 };
 395                 map1 {
 396                         /* Corresponds to 200MHz at freq_table */
 397                         cooling-device = <&cpu0 13 13>, <&cpu1 13 13>,
 398                                          <&cpu2 13 13>, <&cpu3 13 13>;
 399                 };
 400         };
 401 };
 402
 403 &csis_0 {
 404         status = "okay";
 405         vddcore-supply = <&ldo8_reg>;
 406         vddio-supply = <&ldo10_reg>;
 407         assigned-clocks = <&clock CLK_MOUT_CSIS0>,
 408                         <&clock CLK_SCLK_CSIS0>;
 409         assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
 410         assigned-clock-rates = <0>, <176000000>;
 411
 412         /* Camera C (3) MIPI CSI-2 (CSIS0) */
 413         port@3 {
 414                 reg = <3>;
 415                 csis0_ep: endpoint {
 416                         remote-endpoint = <&s5c73m3_ep>;
 417                         data-lanes = <1 2 3 4>;
 418                         samsung,csis-hs-settle = <12>;
 419                 };
 420         };
 421 };
 422
 423 &csis_1 {
 424         status = "okay";
 425         vddcore-supply = <&ldo8_reg>;
 426         vddio-supply = <&ldo10_reg>;
 427         assigned-clocks = <&clock CLK_MOUT_CSIS1>,
 428                         <&clock CLK_SCLK_CSIS1>;
 429         assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
 430         assigned-clock-rates = <0>, <176000000>;
 431
 432         /* Camera D (4) MIPI CSI-2 (CSIS1) */
 433         port@4 {
 434                 reg = <4>;
 435                 csis1_ep: endpoint {
 436                         remote-endpoint = <&is_s5k6a3_ep>;
 437                         data-lanes = <1>;
 438                         samsung,csis-hs-settle = <18>;
 439                         samsung,csis-wclk;
 440                 };
 441         };
 442 };
 443
 444 &dsi_0 {
 445         vddcore-supply = <&ldo8_reg>;
 446         vddio-supply = <&ldo10_reg>;
 447         samsung,burst-clock-frequency = <500000000>;
 448         samsung,esc-clock-frequency = <20000000>;
 449         samsung,pll-clock-frequency = <24000000>;
 450 };
 451
 452 &exynos_usbphy {
 453         vbus-supply = <&esafeout1_reg>;
 454         status = "okay";
 455 };
 456
 457 &fimc_0 {
 458         status = "okay";
 459         assigned-clocks = <&clock CLK_MOUT_FIMC0>,
 460                         <&clock CLK_SCLK_FIMC0>;
 461         assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
 462         assigned-clock-rates = <0>, <176000000>;
 463 };
 464
 465 &fimc_1 {
 466         status = "okay";
 467         assigned-clocks = <&clock CLK_MOUT_FIMC1>,
 468                         <&clock CLK_SCLK_FIMC1>;
 469         assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
 470         assigned-clock-rates = <0>, <176000000>;
 471 };
 472
 473 &fimc_2 {
 474         status = "okay";
 475         assigned-clocks = <&clock CLK_MOUT_FIMC2>,
 476                         <&clock CLK_SCLK_FIMC2>;
 477         assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
 478         assigned-clock-rates = <0>, <176000000>;
 479 };
 480
 481 &fimc_3 {
 482         status = "okay";
 483         assigned-clocks = <&clock CLK_MOUT_FIMC3>,
 484                         <&clock CLK_SCLK_FIMC3>;
 485         assigned-clock-parents = <&clock CLK_MOUT_MPLL_USER_T>;
 486         assigned-clock-rates = <0>, <176000000>;
 487 };
 488
 489 &fimc_is {
 490         pinctrl-0 = <&fimc_is_uart>;
 491         pinctrl-names = "default";
 492         status = "okay";
 493
 494         };
 495
 496 &fimc_lite_0 {
 497         status = "okay";
 498 };
 499
 500 &fimc_lite_1 {
 501         status = "okay";
 502 };
 503
 504 &fimd {
 505         status = "okay";
 506 };
 507
 508 &gpu {
 509         mali-supply = <&buck4_reg>;
 510         status = "okay";
 511 };
 512
 513 &hdmi {
 514         hpd-gpios = <&gpx3 7 GPIO_ACTIVE_HIGH>;
 515         pinctrl-names = "default";
 516         pinctrl-0 = <&hdmi_hpd>;
 517         vdd-supply = <&ldo3_reg>;
 518         vdd_osc-supply = <&ldo4_reg>;
 519         vdd_pll-supply = <&ldo3_reg>;
 520         ddc = <&i2c_5>;
 521         status = "okay";
 522
 523         ports {
 524                 #address-cells = <1>;
 525                 #size-cells = <0>;
 526
 527                 port@1 {
 528                         reg = <1>;
 529                         hdmi_to_mhl: endpoint {
 530                                 remote-endpoint = <&mhl_to_hdmi>;
 531                         };
 532                 };
 533         };
 534 };
 535
 536 &hsotg {
 537         vusb_d-supply = <&ldo15_reg>;
 538         vusb_a-supply = <&ldo12_reg>;
 539         dr_mode = "peripheral";
 540         status = "okay";
 541 };
 542
 543 &i2c_0 {
 544         samsung,i2c-sda-delay = <100>;
 545         samsung,i2c-slave-addr = <0x10>;
 546         samsung,i2c-max-bus-freq = <400000>;
 547         pinctrl-0 = <&i2c0_bus>;
 548         pinctrl-names = "default";
 549         status = "okay";
 550
 551         s5c73m3: image-sensor@3c {
 552                 compatible = "samsung,s5c73m3";
 553                 reg = <0x3c>;
 554                 xshutdown-gpios = <&gpf1 3 GPIO_ACTIVE_LOW>; /* ISP_RESET */
 555                 vdd-int-supply = <&buck9_reg>;
 556                 vddio-cis-supply = <&ldo9_reg>;
 557                 vddio-host-supply = <&ldo18_reg>;
 558                 vdd-af-supply = <&cam_af_reg>;
 559                 vdd-reg-supply = <&cam_io_reg>;
 560                 clock-frequency = <24000000>;
 561                 /* CAM_A_CLKOUT */
 562                 clocks = <&camera 0>;
 563                 clock-names = "cis_extclk";
 564                 status = "disabled";
 565                 port {
 566                         s5c73m3_ep: endpoint {
 567                                 remote-endpoint = <&csis0_ep>;
 568                                 data-lanes = <1 2 3 4>;
 569                         };
 570                 };
 571         };
 572 };
 573
 574 &i2c1_isp {
 575         pinctrl-0 = <&fimc_is_i2c1>;
 576         pinctrl-names = "default";
 577
 578         image-sensor@10 {
 579                 compatible = "samsung,s5k6a3";
 580                 reg = <0x10>;
 581                 svdda-supply = <&cam_io_reg>;
 582                 svddio-supply = <&ldo19_reg>;
 583                 afvdd-supply = <&ldo19_reg>;
 584                 clock-frequency = <24000000>;
 585                 /* CAM_B_CLKOUT */
 586                 clocks = <&camera 1>;
 587                 clock-names = "extclk";
 588                 samsung,camclk-out = <1>;
 589                 gpios = <&gpm1 6 GPIO_ACTIVE_LOW>;
 590
 591                 port {
 592                         is_s5k6a3_ep: endpoint {
 593                                 remote-endpoint = <&csis1_ep>;
 594                                 data-lanes = <1>;
 595                         };
 596                 };
 597         };
 598 };
 599
 600 &i2c_3 {
 601         samsung,i2c-sda-delay = <100>;
 602         samsung,i2c-slave-addr = <0x10>;
 603         samsung,i2c-max-bus-freq = <400000>;
 604         pinctrl-0 = <&i2c3_bus>;
 605         pinctrl-names = "default";
 606         status = "okay";
 607 };
 608
 609 &i2c_4 {
 610         samsung,i2c-sda-delay = <100>;
 611         samsung,i2c-slave-addr = <0x10>;
 612         samsung,i2c-max-bus-freq = <100000>;
 613         pinctrl-0 = <&i2c4_bus>;
 614         pinctrl-names = "default";
 615         status = "okay";
 616
 617         wm1811: audio-codec@1a {
 618                 compatible = "wlf,wm1811";
 619                 reg = <0x1a>;
 620                 clocks = <&pmu_system_controller 0>,
 621                         <&max77686 MAX77686_CLK_PMIC>;
 622                 clock-names = "MCLK1", "MCLK2";
 623                 interrupt-controller;
 624                 #interrupt-cells = <2>;
 625                 interrupt-parent = <&gpx3>;
 626                 interrupts = <6 IRQ_TYPE_LEVEL_HIGH>;
 627
 628                 gpio-controller;
 629                 #gpio-cells = <2>;
 630                 #sound-dai-cells = <0>;
 631
 632                 wlf,gpio-cfg = <0x3 0x0 0x0 0x0 0x0 0x0
 633                         0x0 0x8000 0x0 0x0 0x0>;
 634                 wlf,micbias-cfg = <0x2f 0x2b>;
 635
 636                 wlf,lineout1-feedback;
 637                 wlf,lineout1-se;
 638                 wlf,lineout2-se;
 639                 wlf,ldoena-always-driven;
 640
 641                 AVDD2-supply = <&vbatt_reg>;
 642                 DBVDD1-supply = <&ldo3_reg>;
 643                 DBVDD2-supply = <&vbatt_reg>;
 644                 DBVDD3-supply = <&vbatt_reg>;
 645                 DCVDD-supply = <&ldo3_reg>;
 646                 CPVDD-supply = <&vbatt_reg>;
 647                 SPKVDD1-supply = <&vbatt_reg>;
 648                 SPKVDD2-supply = <&vbatt_reg>;
 649                 wlf,ldo1ena = <&gpj0 4 0>;
 650                 wlf,ldo2ena = <&gpj0 4 0>;
 651         };
 652 };
 653
 654 &i2c_5 {
 655         status = "okay";
 656 };
 657
 658 &i2c_7 {
 659         samsung,i2c-sda-delay = <100>;
 660         samsung,i2c-slave-addr = <0x10>;
 661         samsung,i2c-max-bus-freq = <100000>;
 662         pinctrl-0 = <&i2c7_bus>;
 663         pinctrl-names = "default";
 664         status = "okay";
 665
 666         max77686: pmic@9 {
 667                 compatible = "maxim,max77686";
 668                 interrupt-parent = <&gpx0>;
 669                 interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
 670                 pinctrl-0 = <&max77686_irq>;
 671                 pinctrl-names = "default";
 672                 wakeup-source;
 673                 reg = <0x09>;
 674                 #clock-cells = <1>;
 675
 676                 voltage-regulators {
 677                         ldo1_reg: LDO1 {
 678                                 regulator-name = "VALIVE_1.0V_AP";
 679                                 regulator-min-microvolt = <1000000>;
 680                                 regulator-max-microvolt = <1000000>;
 681                                 regulator-always-on;
 682                         };
 683
 684                         ldo2_reg: LDO2 {
 685                                 regulator-name = "VM1M2_1.2V_AP";
 686                                 regulator-min-microvolt = <1200000>;
 687                                 regulator-max-microvolt = <1200000>;
 688                                 regulator-always-on;
 689                                 regulator-state-mem {
 690                                         regulator-on-in-suspend;
 691                                 };
 692                         };
 693
 694                         ldo3_reg: LDO3 {
 695                                 regulator-name = "VCC_1.8V_AP";
 696                                 regulator-min-microvolt = <1800000>;
 697                                 regulator-max-microvolt = <1800000>;
 698                                 regulator-always-on;
 699                         };
 700
 701                         ldo4_reg: LDO4 {
 702                                 regulator-name = "VCC_2.8V_AP";
 703                                 regulator-min-microvolt = <2800000>;
 704                                 regulator-max-microvolt = <2800000>;
 705                                 regulator-always-on;
 706                         };
 707
 708                         ldo5_reg: LDO5 {
 709                                 regulator-name = "VCC_1.8V_IO";
 710                                 regulator-min-microvolt = <1800000>;
 711                                 regulator-max-microvolt = <1800000>;
 712                                 regulator-always-on;
 713                         };
 714
 715                         ldo6_reg: LDO6 {
 716                                 regulator-name = "VMPLL_1.0V_AP";
 717                                 regulator-min-microvolt = <1000000>;
 718                                 regulator-max-microvolt = <1000000>;
 719                                 regulator-always-on;
 720                                 regulator-state-mem {
 721                                         regulator-on-in-suspend;
 722                                 };
 723                         };
 724
 725                         ldo7_reg: LDO7 {
 726                                 regulator-name = "VPLL_1.0V_AP";
 727                                 regulator-min-microvolt = <1000000>;
 728                                 regulator-max-microvolt = <1000000>;
 729                                 regulator-always-on;
 730                                 regulator-state-mem {
 731                                         regulator-on-in-suspend;
 732                                 };
 733                         };
 734
 735                         ldo8_reg: LDO8 {
 736                                 regulator-name = "VMIPI_1.0V";
 737                                 regulator-min-microvolt = <1000000>;
 738                                 regulator-max-microvolt = <1000000>;
 739                                 regulator-state-mem {
 740                                         regulator-off-in-suspend;
 741                                 };
 742                         };
 743
 744                         ldo9_reg: LDO9 {
 745                                 regulator-name = "CAM_ISP_MIPI_1.2V";
 746                                 regulator-min-microvolt = <1200000>;
 747                                 regulator-max-microvolt = <1200000>;
 748                         };
 749
 750                         ldo10_reg: LDO10 {
 751                                 regulator-name = "VMIPI_1.8V";
 752                                 regulator-min-microvolt = <1800000>;
 753                                 regulator-max-microvolt = <1800000>;
 754                                 regulator-state-mem {
 755                                         regulator-off-in-suspend;
 756                                 };
 757                         };
 758
 759                         ldo11_reg: LDO11 {
 760                                 regulator-name = "VABB1_1.95V";
 761                                 regulator-min-microvolt = <1950000>;
 762                                 regulator-max-microvolt = <1950000>;
 763                                 regulator-always-on;
 764                                 regulator-state-mem {
 765                                         regulator-off-in-suspend;
 766                                 };
 767                         };
 768
 769                         ldo12_reg: LDO12 {
 770                                 regulator-name = "VUOTG_3.0V";
 771                                 regulator-min-microvolt = <3000000>;
 772                                 regulator-max-microvolt = <3000000>;
 773                                 regulator-state-mem {
 774                                         regulator-off-in-suspend;
 775                                 };
 776                         };
 777
 778                         ldo13_reg: LDO13 {
 779                                 regulator-name = "NFC_AVDD_1.8V";
 780                                 regulator-min-microvolt = <1800000>;
 781                                 regulator-max-microvolt = <1800000>;
 782                         };
 783
 784                         ldo14_reg: LDO14 {
 785                                 regulator-name = "VABB2_1.95V";
 786                                 regulator-min-microvolt = <1950000>;
 787                                 regulator-max-microvolt = <1950000>;
 788                                 regulator-always-on;
 789                                 regulator-state-mem {
 790                                         regulator-off-in-suspend;
 791                                 };
 792                         };
 793
 794                         ldo15_reg: LDO15 {
 795                                 regulator-name = "VHSIC_1.0V";
 796                                 regulator-min-microvolt = <1000000>;
 797                                 regulator-max-microvolt = <1000000>;
 798                                 regulator-state-mem {
 799                                         regulator-on-in-suspend;
 800                                 };
 801                         };
 802
 803                         ldo16_reg: LDO16 {
 804                                 regulator-name = "VHSIC_1.8V";
 805                                 regulator-min-microvolt = <1800000>;
 806                                 regulator-max-microvolt = <1800000>;
 807                                 regulator-state-mem {
 808                                         regulator-on-in-suspend;
 809                                 };
 810                         };
 811
 812                         ldo17_reg: LDO17 {
 813                                 regulator-name = "CAM_SENSOR_CORE_1.2V";
 814                                 regulator-min-microvolt = <1200000>;
 815                                 regulator-max-microvolt = <1200000>;
 816                         };
 817
 818                         ldo18_reg: LDO18 {
 819                                 regulator-name = "CAM_ISP_SEN_IO_1.8V";
 820                                 regulator-min-microvolt = <1800000>;
 821                                 regulator-max-microvolt = <1800000>;
 822                         };
 823
 824                         ldo19_reg: LDO19 {
 825                                 regulator-name = "VT_CAM_1.8V";
 826                                 regulator-min-microvolt = <1800000>;
 827                                 regulator-max-microvolt = <1800000>;
 828                         };
 829
 830                         ldo20_reg: LDO20 {
 831                                 regulator-name = "VDDQ_PRE_1.8V";
 832                                 regulator-min-microvolt = <1800000>;
 833                                 regulator-max-microvolt = <1800000>;
 834                         };
 835
 836                         ldo21_reg: LDO21 {
 837                                 regulator-name = "VTF_2.8V";
 838                                 regulator-min-microvolt = <2800000>;
 839                                 regulator-max-microvolt = <2800000>;
 840                                 maxim,ena-gpios = <&gpy2 0 GPIO_ACTIVE_HIGH>;
 841                         };
 842
 843                         ldo22_reg: LDO22 {
 844                                 regulator-name = "VMEM_VDD_2.8V";
 845                                 regulator-min-microvolt = <2800000>;
 846                                 regulator-max-microvolt = <2800000>;
 847                                 maxim,ena-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>;
 848                         };
 849
 850                         ldo23_reg: LDO23 {
 851                                 regulator-name = "TSP_AVDD_3.3V";
 852                                 regulator-min-microvolt = <3300000>;
 853                                 regulator-max-microvolt = <3300000>;
 854                         };
 855
 856                         ldo24_reg: LDO24 {
 857                                 regulator-name = "TSP_VDD_1.8V";
 858                                 regulator-min-microvolt = <1800000>;
 859                                 regulator-max-microvolt = <1800000>;
 860                         };
 861
 862                         ldo25_reg: LDO25 {
 863                                 regulator-name = "LDO25";
 864                         };
 865
 866                         ldo26_reg: LDO26 {
 867                                 regulator-name = "MOTOR_VCC_3.0V";
 868                                 regulator-min-microvolt = <3000000>;
 869                                 regulator-max-microvolt = <3000000>;
 870                         };
 871
 872                         buck1_reg: BUCK1 {
 873                                 regulator-name = "VDD_MIF";
 874                                 regulator-min-microvolt = <850000>;
 875                                 regulator-max-microvolt = <1100000>;
 876                                 regulator-always-on;
 877                                 regulator-boot-on;
 878                                 regulator-state-mem {
 879                                         regulator-off-in-suspend;
 880                                 };
 881                         };
 882
 883                         buck2_reg: BUCK2 {
 884                                 regulator-name = "VDD_ARM";
 885                                 regulator-min-microvolt = <850000>;
 886                                 regulator-max-microvolt = <1500000>;
 887                                 regulator-always-on;
 888                                 regulator-boot-on;
 889                                 regulator-state-mem {
 890                                         regulator-on-in-suspend;
 891                                 };
 892                         };
 893
 894                         buck3_reg: BUCK3 {
 895                                 regulator-name = "VDD_INT";
 896                                 regulator-min-microvolt = <850000>;
 897                                 regulator-max-microvolt = <1150000>;
 898                                 regulator-always-on;
 899                                 regulator-boot-on;
 900                                 regulator-state-mem {
 901                                         regulator-off-in-suspend;
 902                                 };
 903                         };
 904
 905                         buck4_reg: BUCK4 {
 906                                 regulator-name = "VDD_G3D";
 907                                 regulator-min-microvolt = <850000>;
 908                                 regulator-max-microvolt = <1150000>;
 909                                 regulator-boot-on;
 910                                 regulator-state-mem {
 911                                         regulator-off-in-suspend;
 912                                 };
 913                         };
 914
 915                         buck5_reg: BUCK5 {
 916                                 regulator-name = "VMEM_1.2V_AP";
 917                                 regulator-min-microvolt = <1200000>;
 918                                 regulator-max-microvolt = <1200000>;
 919                                 regulator-always-on;
 920                         };
 921
 922                         buck6_reg: BUCK6 {
 923                                 regulator-name = "VCC_SUB_1.35V";
 924                                 regulator-min-microvolt = <1350000>;
 925                                 regulator-max-microvolt = <1350000>;
 926                                 regulator-always-on;
 927                         };
 928
 929                         buck7_reg: BUCK7 {
 930                                 regulator-name = "VCC_SUB_2.0V";
 931                                 regulator-min-microvolt = <2000000>;
 932                                 regulator-max-microvolt = <2000000>;
 933                                 regulator-always-on;
 934                         };
 935
 936                         buck8_reg: BUCK8 {
 937                                 regulator-name = "VMEM_VDDF_3.0V";
 938                                 regulator-min-microvolt = <2850000>;
 939                                 regulator-max-microvolt = <2850000>;
 940                                 maxim,ena-gpios = <&gpk0 2 GPIO_ACTIVE_HIGH>;
 941                         };
 942
 943                         buck9_reg: BUCK9 {
 944                                 regulator-name = "CAM_ISP_CORE_1.2V";
 945                                 regulator-min-microvolt = <1000000>;
 946                                 regulator-max-microvolt = <1200000>;
 947                         };
 948                 };
 949         };
 950 };
 951
 952 &i2c_8 {
 953         status = "okay";
 954 };
 955
 956 &i2s0 {
 957         pinctrl-0 = <&i2s0_bus>;
 958         pinctrl-names = "default";
 959         status = "okay";
 960 };
 961
 962 &mixer {
 963         status = "okay";
 964 };
 965
 966 &mshc_0 {
 967         broken-cd;
 968         non-removable;
 969         card-detect-delay = <200>;
 970         vmmc-supply = <&ldo22_reg>;
 971         clock-frequency = <400000000>;
 972         samsung,dw-mshc-ciu-div = <0>;
 973         samsung,dw-mshc-sdr-timing = <2 3>;
 974         samsung,dw-mshc-ddr-timing = <1 2>;
 975         pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
 976         pinctrl-names = "default";
 977         status = "okay";
 978         bus-width = <8>;
 979         cap-mmc-highspeed;
 980 };
 981
 982 &pmu_system_controller {
 983         assigned-clocks = <&pmu_system_controller 0>;
 984         assigned-clock-parents =  <&clock CLK_XUSBXTI>;
 985 };
 986
 987 &pinctrl_0 {
 988         pinctrl-names = "default";
 989         pinctrl-0 = <&sleep0>;
 990
 991         mhl_int: mhl-int-pins {
 992                 samsung,pins = "gpf3-5";
 993                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
 994         };
 995
 996         i2c_mhl_bus: i2c-mhl-bus-pins {
 997                 samsung,pins = "gpf0-4", "gpf0-6";
 998                 samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
 999                 samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
1000                 samsung,pin-drv = <EXYNOS4_PIN_DRV_LV1>;
1001         };
1002
1003         sleep0: sleep-state {
1004                 PIN_SLP(gpa0-0, INPUT, NONE);
1005                 PIN_SLP(gpa0-1, OUT0, NONE);
1006                 PIN_SLP(gpa0-2, INPUT, NONE);
1007                 PIN_SLP(gpa0-3, INPUT, UP);
1008                 PIN_SLP(gpa0-4, INPUT, NONE);
1009                 PIN_SLP(gpa0-5, INPUT, DOWN);
1010                 PIN_SLP(gpa0-6, INPUT, DOWN);
1011                 PIN_SLP(gpa0-7, INPUT, UP);
1012
1013                 PIN_SLP(gpa1-0, INPUT, DOWN);
1014                 PIN_SLP(gpa1-1, INPUT, DOWN);
1015                 PIN_SLP(gpa1-2, INPUT, DOWN);
1016                 PIN_SLP(gpa1-3, INPUT, DOWN);
1017                 PIN_SLP(gpa1-4, INPUT, DOWN);
1018                 PIN_SLP(gpa1-5, INPUT, DOWN);
1019
1020                 PIN_SLP(gpb-0, INPUT, NONE);
1021                 PIN_SLP(gpb-1, INPUT, NONE);
1022                 PIN_SLP(gpb-2, INPUT, NONE);
1023                 PIN_SLP(gpb-3, INPUT, NONE);
1024                 PIN_SLP(gpb-4, INPUT, DOWN);
1025                 PIN_SLP(gpb-5, INPUT, UP);
1026                 PIN_SLP(gpb-6, INPUT, DOWN);
1027                 PIN_SLP(gpb-7, INPUT, DOWN);
1028
1029                 PIN_SLP(gpc0-0, INPUT, DOWN);
1030                 PIN_SLP(gpc0-1, INPUT, DOWN);
1031                 PIN_SLP(gpc0-2, INPUT, DOWN);
1032                 PIN_SLP(gpc0-3, INPUT, DOWN);
1033                 PIN_SLP(gpc0-4, INPUT, DOWN);
1034
1035                 PIN_SLP(gpc1-0, INPUT, NONE);
1036                 PIN_SLP(gpc1-1, PREV, NONE);
1037                 PIN_SLP(gpc1-2, INPUT, NONE);
1038                 PIN_SLP(gpc1-3, INPUT, NONE);
1039                 PIN_SLP(gpc1-4, INPUT, NONE);
1040
1041                 PIN_SLP(gpd0-0, INPUT, DOWN);
1042                 PIN_SLP(gpd0-1, INPUT, DOWN);
1043                 PIN_SLP(gpd0-2, INPUT, NONE);
1044                 PIN_SLP(gpd0-3, INPUT, NONE);
1045
1046                 PIN_SLP(gpd1-0, INPUT, DOWN);
1047                 PIN_SLP(gpd1-1, INPUT, DOWN);
1048                 PIN_SLP(gpd1-2, INPUT, NONE);
1049                 PIN_SLP(gpd1-3, INPUT, NONE);
1050
1051                 PIN_SLP(gpf0-0, INPUT, NONE);
1052                 PIN_SLP(gpf0-1, INPUT, NONE);
1053                 PIN_SLP(gpf0-2, INPUT, DOWN);
1054                 PIN_SLP(gpf0-3, INPUT, DOWN);
1055                 PIN_SLP(gpf0-4, INPUT, NONE);
1056                 PIN_SLP(gpf0-5, INPUT, DOWN);
1057                 PIN_SLP(gpf0-6, INPUT, NONE);
1058                 PIN_SLP(gpf0-7, INPUT, DOWN);
1059
1060                 PIN_SLP(gpf1-0, INPUT, DOWN);
1061                 PIN_SLP(gpf1-1, INPUT, DOWN);
1062                 PIN_SLP(gpf1-2, INPUT, DOWN);
1063                 PIN_SLP(gpf1-3, INPUT, DOWN);
1064                 PIN_SLP(gpf1-4, INPUT, NONE);
1065                 PIN_SLP(gpf1-5, INPUT, NONE);
1066                 PIN_SLP(gpf1-6, INPUT, DOWN);
1067                 PIN_SLP(gpf1-7, PREV, NONE);
1068
1069                 PIN_SLP(gpf2-0, PREV, NONE);
1070                 PIN_SLP(gpf2-1, INPUT, DOWN);
1071                 PIN_SLP(gpf2-2, INPUT, DOWN);
1072                 PIN_SLP(gpf2-3, INPUT, DOWN);
1073                 PIN_SLP(gpf2-4, INPUT, DOWN);
1074                 PIN_SLP(gpf2-5, INPUT, DOWN);
1075                 PIN_SLP(gpf2-6, INPUT, NONE);
1076                 PIN_SLP(gpf2-7, INPUT, NONE);
1077
1078                 PIN_SLP(gpf3-0, INPUT, NONE);
1079                 PIN_SLP(gpf3-1, PREV, NONE);
1080                 PIN_SLP(gpf3-2, PREV, NONE);
1081                 PIN_SLP(gpf3-3, PREV, NONE);
1082                 PIN_SLP(gpf3-4, OUT1, NONE);
1083                 PIN_SLP(gpf3-5, INPUT, DOWN);
1084
1085                 PIN_SLP(gpj0-0, PREV, NONE);
1086                 PIN_SLP(gpj0-1, PREV, NONE);
1087                 PIN_SLP(gpj0-2, PREV, NONE);
1088                 PIN_SLP(gpj0-3, INPUT, DOWN);
1089                 PIN_SLP(gpj0-4, PREV, NONE);
1090                 PIN_SLP(gpj0-5, PREV, NONE);
1091                 PIN_SLP(gpj0-6, INPUT, DOWN);
1092                 PIN_SLP(gpj0-7, INPUT, DOWN);
1093
1094                 PIN_SLP(gpj1-0, INPUT, DOWN);
1095                 PIN_SLP(gpj1-1, PREV, NONE);
1096                 PIN_SLP(gpj1-2, PREV, NONE);
1097                 PIN_SLP(gpj1-3, INPUT, DOWN);
1098                 PIN_SLP(gpj1-4, INPUT, DOWN);
1099         };
1100 };
1101
1102 &pinctrl_1 {
1103         pinctrl-names = "default";
1104         pinctrl-0 = <&sleep1>;
1105
1106         gpio_keys: gpio-keys-pins {
1107                 samsung,pins = "gpx0-1", "gpx2-2", "gpx2-7", "gpx3-3";
1108                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
1109         };
1110
1111         bt_shutdown: bt-shutdown-pins {
1112                 samsung,pins = "gpl0-6";
1113                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
1114         };
1115
1116         bt_host_wakeup: bt-host-wakeup-pins {
1117                 samsung,pins = "gpx2-6";
1118                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
1119         };
1120
1121         bt_device_wakeup: bt-device-wakeup-pins {
1122                 samsung,pins = "gpx3-1";
1123                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
1124         };
1125
1126         max77686_irq: max77686-irq-pins {
1127                 samsung,pins = "gpx0-7";
1128                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
1129         };
1130
1131         max77693_irq: max77693-irq-pins {
1132                 samsung,pins = "gpx1-5";
1133                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
1134         };
1135
1136         max77693_fuel_irq: max77693-fuel-irq-pins {
1137                 samsung,pins = "gpx2-3";
1138                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
1139         };
1140
1141         sdhci2_cd: sdhci2-cd-irq-pins {
1142                 samsung,pins = "gpx3-4";
1143                 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
1144         };
1145
1146         hdmi_hpd: hdmi-hpd-pins {
1147                 samsung,pins = "gpx3-7";
1148                 samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
1149         };
1150
1151         sleep1: sleep-state {
1152                 PIN_SLP(gpk0-0, PREV, NONE);
1153                 PIN_SLP(gpk0-1, PREV, NONE);
1154                 PIN_SLP(gpk0-2, OUT0, NONE);
1155                 PIN_SLP(gpk0-3, PREV, NONE);
1156                 PIN_SLP(gpk0-4, PREV, NONE);
1157                 PIN_SLP(gpk0-5, PREV, NONE);
1158                 PIN_SLP(gpk0-6, PREV, NONE);
1159
1160                 PIN_SLP(gpk1-0, INPUT, DOWN);
1161                 PIN_SLP(gpk1-1, INPUT, DOWN);
1162                 PIN_SLP(gpk1-2, INPUT, DOWN);
1163                 PIN_SLP(gpk1-3, PREV, NONE);
1164                 PIN_SLP(gpk1-4, PREV, NONE);
1165                 PIN_SLP(gpk1-5, PREV, NONE);
1166                 PIN_SLP(gpk1-6, PREV, NONE);
1167
1168                 PIN_SLP(gpk2-0, INPUT, DOWN);
1169                 PIN_SLP(gpk2-1, INPUT, DOWN);
1170                 PIN_SLP(gpk2-2, INPUT, DOWN);
1171                 PIN_SLP(gpk2-3, INPUT, DOWN);
1172                 PIN_SLP(gpk2-4, INPUT, DOWN);
1173                 PIN_SLP(gpk2-5, INPUT, DOWN);
1174                 PIN_SLP(gpk2-6, INPUT, DOWN);
1175
1176                 PIN_SLP(gpk3-0, OUT0, NONE);
1177                 PIN_SLP(gpk3-1, INPUT, NONE);
1178                 PIN_SLP(gpk3-2, INPUT, DOWN);
1179                 PIN_SLP(gpk3-3, INPUT, NONE);
1180                 PIN_SLP(gpk3-4, INPUT, NONE);
1181                 PIN_SLP(gpk3-5, INPUT, NONE);
1182                 PIN_SLP(gpk3-6, INPUT, NONE);
1183
1184                 PIN_SLP(gpl0-0, INPUT, DOWN);
1185                 PIN_SLP(gpl0-1, INPUT, DOWN);
1186                 PIN_SLP(gpl0-2, INPUT, DOWN);
1187                 PIN_SLP(gpl0-3, INPUT, DOWN);
1188                 PIN_SLP(gpl0-4, PREV, NONE);
1189                 PIN_SLP(gpl0-6, PREV, NONE);
1190
1191                 PIN_SLP(gpl1-0, INPUT, DOWN);
1192                 PIN_SLP(gpl1-1, INPUT, DOWN);
1193                 PIN_SLP(gpl2-0, INPUT, DOWN);
1194                 PIN_SLP(gpl2-1, INPUT, DOWN);
1195                 PIN_SLP(gpl2-2, INPUT, DOWN);
1196                 PIN_SLP(gpl2-3, INPUT, DOWN);
1197                 PIN_SLP(gpl2-4, INPUT, DOWN);
1198                 PIN_SLP(gpl2-5, INPUT, DOWN);
1199                 PIN_SLP(gpl2-6, PREV, NONE);
1200                 PIN_SLP(gpl2-7, INPUT, DOWN);
1201
1202                 PIN_SLP(gpm0-0, INPUT, DOWN);
1203                 PIN_SLP(gpm0-1, INPUT, DOWN);
1204                 PIN_SLP(gpm0-2, INPUT, DOWN);
1205                 PIN_SLP(gpm0-3, INPUT, DOWN);
1206                 PIN_SLP(gpm0-4, INPUT, DOWN);
1207                 PIN_SLP(gpm0-5, INPUT, DOWN);
1208                 PIN_SLP(gpm0-6, INPUT, DOWN);
1209                 PIN_SLP(gpm0-7, INPUT, DOWN);
1210
1211                 PIN_SLP(gpm1-0, INPUT, DOWN);
1212                 PIN_SLP(gpm1-1, INPUT, DOWN);
1213                 PIN_SLP(gpm1-2, INPUT, NONE);
1214                 PIN_SLP(gpm1-3, INPUT, NONE);
1215                 PIN_SLP(gpm1-4, INPUT, NONE);
1216                 PIN_SLP(gpm1-5, INPUT, NONE);
1217                 PIN_SLP(gpm1-6, INPUT, DOWN);
1218
1219                 PIN_SLP(gpm2-0, INPUT, NONE);
1220                 PIN_SLP(gpm2-1, INPUT, NONE);
1221                 PIN_SLP(gpm2-2, INPUT, DOWN);
1222                 PIN_SLP(gpm2-3, INPUT, DOWN);
1223                 PIN_SLP(gpm2-4, INPUT, DOWN);
1224
1225                 PIN_SLP(gpm3-0, PREV, NONE);
1226                 PIN_SLP(gpm3-1, PREV, NONE);
1227                 PIN_SLP(gpm3-2, PREV, NONE);
1228                 PIN_SLP(gpm3-3, OUT1, NONE);
1229                 PIN_SLP(gpm3-4, INPUT, DOWN);
1230                 PIN_SLP(gpm3-5, INPUT, DOWN);
1231                 PIN_SLP(gpm3-6, INPUT, DOWN);
1232                 PIN_SLP(gpm3-7, INPUT, DOWN);
1233
1234                 PIN_SLP(gpm4-0, INPUT, DOWN);
1235                 PIN_SLP(gpm4-1, INPUT, DOWN);
1236                 PIN_SLP(gpm4-2, INPUT, DOWN);
1237                 PIN_SLP(gpm4-3, INPUT, DOWN);
1238                 PIN_SLP(gpm4-4, INPUT, DOWN);
1239                 PIN_SLP(gpm4-5, INPUT, DOWN);
1240                 PIN_SLP(gpm4-6, INPUT, DOWN);
1241                 PIN_SLP(gpm4-7, INPUT, DOWN);
1242
1243                 PIN_SLP(gpy0-0, INPUT, DOWN);
1244                 PIN_SLP(gpy0-1, INPUT, DOWN);
1245                 PIN_SLP(gpy0-2, INPUT, DOWN);
1246                 PIN_SLP(gpy0-3, INPUT, DOWN);
1247                 PIN_SLP(gpy0-4, INPUT, DOWN);
1248                 PIN_SLP(gpy0-5, INPUT, DOWN);
1249
1250                 PIN_SLP(gpy1-0, INPUT, DOWN);
1251                 PIN_SLP(gpy1-1, INPUT, DOWN);
1252                 PIN_SLP(gpy1-2, INPUT, DOWN);
1253                 PIN_SLP(gpy1-3, INPUT, DOWN);
1254
1255                 PIN_SLP(gpy2-0, PREV, NONE);
1256                 PIN_SLP(gpy2-1, INPUT, DOWN);
1257                 PIN_SLP(gpy2-2, INPUT, NONE);
1258                 PIN_SLP(gpy2-3, INPUT, NONE);
1259                 PIN_SLP(gpy2-4, INPUT, NONE);
1260                 PIN_SLP(gpy2-5, INPUT, NONE);
1261
1262                 PIN_SLP(gpy3-0, INPUT, DOWN);
1263                 PIN_SLP(gpy3-1, INPUT, DOWN);
1264                 PIN_SLP(gpy3-2, INPUT, DOWN);
1265                 PIN_SLP(gpy3-3, INPUT, DOWN);
1266                 PIN_SLP(gpy3-4, INPUT, DOWN);
1267                 PIN_SLP(gpy3-5, INPUT, DOWN);
1268                 PIN_SLP(gpy3-6, INPUT, DOWN);
1269                 PIN_SLP(gpy3-7, INPUT, DOWN);
1270
1271                 PIN_SLP(gpy4-0, INPUT, DOWN);
1272                 PIN_SLP(gpy4-1, INPUT, DOWN);
1273                 PIN_SLP(gpy4-2, INPUT, DOWN);
1274                 PIN_SLP(gpy4-3, INPUT, DOWN);
1275                 PIN_SLP(gpy4-4, INPUT, DOWN);
1276                 PIN_SLP(gpy4-5, INPUT, DOWN);
1277                 PIN_SLP(gpy4-6, INPUT, DOWN);
1278                 PIN_SLP(gpy4-7, INPUT, DOWN);
1279
1280                 PIN_SLP(gpy5-0, INPUT, DOWN);
1281                 PIN_SLP(gpy5-1, INPUT, DOWN);
1282                 PIN_SLP(gpy5-2, INPUT, DOWN);
1283                 PIN_SLP(gpy5-3, INPUT, DOWN);
1284                 PIN_SLP(gpy5-4, INPUT, DOWN);
1285                 PIN_SLP(gpy5-5, INPUT, DOWN);
1286                 PIN_SLP(gpy5-6, INPUT, DOWN);
1287                 PIN_SLP(gpy5-7, INPUT, DOWN);
1288
1289                 PIN_SLP(gpy6-0, INPUT, DOWN);
1290                 PIN_SLP(gpy6-1, INPUT, DOWN);
1291                 PIN_SLP(gpy6-2, INPUT, DOWN);
1292                 PIN_SLP(gpy6-3, INPUT, DOWN);
1293                 PIN_SLP(gpy6-4, INPUT, DOWN);
1294                 PIN_SLP(gpy6-5, INPUT, DOWN);
1295                 PIN_SLP(gpy6-6, INPUT, DOWN);
1296                 PIN_SLP(gpy6-7, INPUT, DOWN);
1297         };
1298 };
1299
1300 &pinctrl_2 {
1301         pinctrl-names = "default";
1302         pinctrl-0 = <&sleep2>;
1303
1304         sleep2: sleep-state {
1305                 PIN_SLP(gpz-0, INPUT, DOWN);
1306                 PIN_SLP(gpz-1, INPUT, DOWN);
1307                 PIN_SLP(gpz-2, INPUT, DOWN);
1308                 PIN_SLP(gpz-3, INPUT, DOWN);
1309                 PIN_SLP(gpz-4, INPUT, DOWN);
1310                 PIN_SLP(gpz-5, INPUT, DOWN);
1311                 PIN_SLP(gpz-6, INPUT, DOWN);
1312         };
1313 };
1314
1315 &pinctrl_3 {
1316         pinctrl-names = "default";
1317         pinctrl-0 = <&sleep3>;
1318
1319         sleep3: sleep-state {
1320                 PIN_SLP(gpv0-0, INPUT, DOWN);
1321                 PIN_SLP(gpv0-1, INPUT, DOWN);
1322                 PIN_SLP(gpv0-2, INPUT, DOWN);
1323                 PIN_SLP(gpv0-3, INPUT, DOWN);
1324                 PIN_SLP(gpv0-4, INPUT, DOWN);
1325                 PIN_SLP(gpv0-5, INPUT, DOWN);
1326                 PIN_SLP(gpv0-6, INPUT, DOWN);
1327                 PIN_SLP(gpv0-7, INPUT, DOWN);
1328
1329                 PIN_SLP(gpv1-0, INPUT, DOWN);
1330                 PIN_SLP(gpv1-1, INPUT, DOWN);
1331                 PIN_SLP(gpv1-2, INPUT, DOWN);
1332                 PIN_SLP(gpv1-3, INPUT, DOWN);
1333                 PIN_SLP(gpv1-4, INPUT, DOWN);
1334                 PIN_SLP(gpv1-5, INPUT, DOWN);
1335                 PIN_SLP(gpv1-6, INPUT, DOWN);
1336                 PIN_SLP(gpv1-7, INPUT, DOWN);
1337
1338                 PIN_SLP(gpv2-0, INPUT, DOWN);
1339                 PIN_SLP(gpv2-1, INPUT, DOWN);
1340                 PIN_SLP(gpv2-2, INPUT, DOWN);
1341                 PIN_SLP(gpv2-3, INPUT, DOWN);
1342                 PIN_SLP(gpv2-4, INPUT, DOWN);
1343                 PIN_SLP(gpv2-5, INPUT, DOWN);
1344                 PIN_SLP(gpv2-6, INPUT, DOWN);
1345                 PIN_SLP(gpv2-7, INPUT, DOWN);
1346
1347                 PIN_SLP(gpv3-0, INPUT, DOWN);
1348                 PIN_SLP(gpv3-1, INPUT, DOWN);
1349                 PIN_SLP(gpv3-2, INPUT, DOWN);
1350                 PIN_SLP(gpv3-3, INPUT, DOWN);
1351                 PIN_SLP(gpv3-4, INPUT, DOWN);
1352                 PIN_SLP(gpv3-5, INPUT, DOWN);
1353                 PIN_SLP(gpv3-6, INPUT, DOWN);
1354                 PIN_SLP(gpv3-7, INPUT, DOWN);
1355
1356                 PIN_SLP(gpv4-0, INPUT, DOWN);
1357         };
1358 };
1359
1360 &pwm {
1361         pinctrl-0 = <&pwm0_out>;
1362         pinctrl-names = "default";
1363         samsung,pwm-outputs = <0>;
1364         status = "okay";
1365 };
1366
1367 &rtc {
1368         status = "okay";
1369         clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>;
1370         clock-names = "rtc", "rtc_src";
1371 };
1372
1373 &sdhci_2 {
1374         bus-width = <4>;
1375         cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>;
1376         pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sdhci2_cd>;
1377         pinctrl-names = "default";
1378         vmmc-supply = <&ldo21_reg>;
1379         status = "okay";
1380 };
1381
1382 &sdhci_3 {
1383         #address-cells = <1>;
1384         #size-cells = <0>;
1385         non-removable;
1386         bus-width = <4>;
1387
1388         mmc-pwrseq = <&wlan_pwrseq>;
1389         pinctrl-names = "default";
1390         pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_bus4>;
1391         status = "okay";
1392
1393         brcmf: wifi@1 {
1394                 reg = <1>;
1395                 compatible = "brcm,bcm4329-fmac";
1396                 interrupt-parent = <&gpx2>;
1397                 interrupts = <5 IRQ_TYPE_NONE>;
1398                 interrupt-names = "host-wake";
1399         };
1400 };
1401
1402 &serial_0 {
1403         pinctrl-0 = <&uart0_data &uart0_fctl>;
1404         pinctrl-names = "default";
1405         status = "okay";
1406
1407         bluetooth {
1408                 compatible = "brcm,bcm4330-bt";
1409                 pinctrl-0 = <&bt_shutdown &bt_device_wakeup &bt_host_wakeup>;
1410                 pinctrl-names = "default";
1411                 max-speed = <3000000>;
1412                 shutdown-gpios = <&gpl0 6 GPIO_ACTIVE_HIGH>;
1413                 device-wakeup-gpios = <&gpx3 1 GPIO_ACTIVE_HIGH>;
1414                 host-wakeup-gpios = <&gpx2 6 GPIO_ACTIVE_HIGH>;
1415                 clocks = <&max77686 MAX77686_CLK_PMIC>;
1416         };
1417 };
1418
1419 &serial_1 {
1420         status = "okay";
1421 };
1422
1423 &serial_2 {
1424         status = "okay";
1425 };
1426
1427 &serial_3 {
1428         status = "okay";
1429 };
1430
1431 &spi_1 {
1432         pinctrl-names = "default";
1433         pinctrl-0 = <&spi1_bus>;
1434         cs-gpios = <&gpb 5 GPIO_ACTIVE_HIGH>;
1435         status = "okay";
1436
1437         s5c73m3_spi: image-sensor@0 {
1438                 compatible = "samsung,s5c73m3";
1439                 spi-max-frequency = <50000000>;
1440                 reg = <0>;
1441                 controller-data {
1442                         samsung,spi-feedback-delay = <2>;
1443                 };
1444         };
1445 };
1446
1447 &tmu {
1448         vtmu-supply = <&ldo10_reg>;
1449         status = "okay";
1450 };