arch/arm/boot/dts/bcm283x.dtsi

   1 #include <dt-bindings/pinctrl/bcm2835.h>
   2 #include <dt-bindings/clock/bcm2835.h>
   3 #include <dt-bindings/clock/bcm2835-aux.h>
   4 #include <dt-bindings/gpio/gpio.h>
   5 #include <dt-bindings/interrupt-controller/irq.h>
   6 #include <dt-bindings/soc/bcm2835-pm.h>
   7
   8 /* firmware-provided startup stubs live here, where the secondary CPUs are
   9  * spinning.
  10  */
  11 /memreserve/ 0x00000000 0x00001000;
  12
  13 /* This include file covers the common peripherals and configuration between
  14  * bcm2835 and bcm2836 implementations, leaving the CPU configuration to
  15  * bcm2835.dtsi and bcm2836.dtsi.
  16  */
  17
  18 / {
  19         compatible = "brcm,bcm2835";
  20         model = "BCM2835";
  21         #address-cells = <1>;
  22         #size-cells = <1>;
  23
  24         aliases {
  25                 serial0 = &uart0;
  26                 serial1 = &uart1;
  27         };
  28
  29         chosen {
  30                 stdout-path = "serial0:115200n8";
  31         };
  32
  33         rmem: reserved-memory {
  34                 #address-cells = <1>;
  35                 #size-cells = <1>;
  36                 ranges;
  37
  38                 cma: linux,cma {
  39                         compatible = "shared-dma-pool";
  40                         size = <0x4000000>; /* 64MB */
  41                         reusable;
  42                         linux,cma-default;
  43                 };
  44         };
  45
  46         thermal-zones {
  47                 cpu_thermal: cpu-thermal {
  48                         polling-delay-passive = <0>;
  49                         polling-delay = <1000>;
  50
  51                         trips {
  52                                 cpu-crit {
  53                                         temperature     = <90000>;
  54                                         hysteresis      = <0>;
  55                                         type            = "critical";
  56                                 };
  57                         };
  58
  59                         cooling-maps {
  60                         };
  61                 };
  62         };
  63
  64         soc {
  65                 compatible = "simple-bus";
  66                 #address-cells = <1>;
  67                 #size-cells = <1>;
  68
  69                 system_timer: timer@7e003000 {
  70                         compatible = "brcm,bcm2835-system-timer";
  71                         reg = <0x7e003000 0x1000>;
  72                         interrupts = <1 0>, <1 1>, <1 2>, <1 3>;
  73                         /* This could be a reference to BCM2835_CLOCK_TIMER,
  74                          * but we don't have the driver using the common clock
  75                          * support yet.
  76                          */
  77                         clock-frequency = <1000000>;
  78                 };
  79
  80                 txp: txp@7e004000 {
  81                         compatible = "brcm,bcm2835-txp";
  82                         reg = <0x7e004000 0x20>;
  83                         interrupts = <1 11>;
  84                 };
  85
  86                 clocks: cprman@7e101000 {
  87                         compatible = "brcm,bcm2835-cprman";
  88                         #clock-cells = <1>;
  89                         reg = <0x7e101000 0x2000>;
  90
  91                         /* CPRMAN derives almost everything from the
  92                          * platform's oscillator.  However, the DSI
  93                          * pixel clocks come from the DSI analog PHY.
  94                          */
  95                         clocks = <&clk_osc>,
  96                                 <&dsi0 0>, <&dsi0 1>, <&dsi0 2>,
  97                                 <&dsi1 0>, <&dsi1 1>, <&dsi1 2>;
  98                 };
  99
 100                 mailbox: mailbox@7e00b880 {
 101                         compatible = "brcm,bcm2835-mbox";
 102                         reg = <0x7e00b880 0x40>;
 103                         interrupts = <0 1>;
 104                         #mbox-cells = <0>;
 105                 };
 106
 107                 gpio: gpio@7e200000 {
 108                         compatible = "brcm,bcm2835-gpio";
 109                         reg = <0x7e200000 0xb4>;
 110                         /*
 111                          * The GPIO IP block is designed for 3 banks of GPIOs.
 112                          * Each bank has a GPIO interrupt for itself.
 113                          * There is an overall "any bank" interrupt.
 114                          * In order, these are GIC interrupts 17, 18, 19, 20.
 115                          * Since the BCM2835 only has 2 banks, the 2nd bank
 116                          * interrupt output appears to be mirrored onto the
 117                          * 3rd bank's interrupt signal.
 118                          * So, a bank0 interrupt shows up on 17, 20, and
 119                          * a bank1 interrupt shows up on 18, 19, 20!
 120                          */
 121                         interrupts = <2 17>, <2 18>, <2 19>, <2 20>;
 122
 123                         gpio-controller;
 124                         #gpio-cells = <2>;
 125
 126                         interrupt-controller;
 127                         #interrupt-cells = <2>;
 128
 129                         gpio-ranges = <&gpio 0 0 54>;
 130
 131                         /* Defines common pin muxing groups
 132                          *
 133                          * While each pin can have its mux selected
 134                          * for various functions individually, some
 135                          * groups only make sense to switch to a
 136                          * particular function together.
 137                          */
 138                         dpi_gpio0: dpi_gpio0 {
 139                                 brcm,pins = <0 1 2 3 4 5 6 7 8 9 10 11
 140                                              12 13 14 15 16 17 18 19
 141                                              20 21 22 23 24 25 26 27>;
 142                                 brcm,function = <BCM2835_FSEL_ALT2>;
 143                         };
 144                         emmc_gpio22: emmc_gpio22 {
 145                                 brcm,pins = <22 23 24 25 26 27>;
 146                                 brcm,function = <BCM2835_FSEL_ALT3>;
 147                         };
 148                         emmc_gpio34: emmc_gpio34 {
 149                                 brcm,pins = <34 35 36 37 38 39>;
 150                                 brcm,function = <BCM2835_FSEL_ALT3>;
 151                                 brcm,pull = <BCM2835_PUD_OFF
 152                                              BCM2835_PUD_UP
 153                                              BCM2835_PUD_UP
 154                                              BCM2835_PUD_UP
 155                                              BCM2835_PUD_UP
 156                                              BCM2835_PUD_UP>;
 157                         };
 158                         emmc_gpio48: emmc_gpio48 {
 159                                 brcm,pins = <48 49 50 51 52 53>;
 160                                 brcm,function = <BCM2835_FSEL_ALT3>;
 161                         };
 162
 163                         gpclk0_gpio4: gpclk0_gpio4 {
 164                                 brcm,pins = <4>;
 165                                 brcm,function = <BCM2835_FSEL_ALT0>;
 166                         };
 167                         gpclk1_gpio5: gpclk1_gpio5 {
 168                                 brcm,pins = <5>;
 169                                 brcm,function = <BCM2835_FSEL_ALT0>;
 170                         };
 171                         gpclk1_gpio42: gpclk1_gpio42 {
 172                                 brcm,pins = <42>;
 173                                 brcm,function = <BCM2835_FSEL_ALT0>;
 174                         };
 175                         gpclk1_gpio44: gpclk1_gpio44 {
 176                                 brcm,pins = <44>;
 177                                 brcm,function = <BCM2835_FSEL_ALT0>;
 178                         };
 179                         gpclk2_gpio6: gpclk2_gpio6 {
 180                                 brcm,pins = <6>;
 181                                 brcm,function = <BCM2835_FSEL_ALT0>;
 182                         };
 183                         gpclk2_gpio43: gpclk2_gpio43 {
 184                                 brcm,pins = <43>;
 185                                 brcm,function = <BCM2835_FSEL_ALT0>;
 186                                 brcm,pull = <BCM2835_PUD_OFF>;
 187                         };
 188
 189                         i2c0_gpio0: i2c0_gpio0 {
 190                                 brcm,pins = <0 1>;
 191                                 brcm,function = <BCM2835_FSEL_ALT0>;
 192                         };
 193                         i2c0_gpio28: i2c0_gpio28 {
 194                                 brcm,pins = <28 29>;
 195                                 brcm,function = <BCM2835_FSEL_ALT0>;
 196                         };
 197                         i2c0_gpio44: i2c0_gpio44 {
 198                                 brcm,pins = <44 45>;
 199                                 brcm,function = <BCM2835_FSEL_ALT1>;
 200                         };
 201                         i2c1_gpio2: i2c1_gpio2 {
 202                                 brcm,pins = <2 3>;
 203                                 brcm,function = <BCM2835_FSEL_ALT0>;
 204                         };
 205                         i2c1_gpio44: i2c1_gpio44 {
 206                                 brcm,pins = <44 45>;
 207                                 brcm,function = <BCM2835_FSEL_ALT2>;
 208                         };
 209
 210                         jtag_gpio22: jtag_gpio22 {
 211                                 brcm,pins = <22 23 24 25 26 27>;
 212                                 brcm,function = <BCM2835_FSEL_ALT4>;
 213                         };
 214
 215                         pcm_gpio18: pcm_gpio18 {
 216                                 brcm,pins = <18 19 20 21>;
 217                                 brcm,function = <BCM2835_FSEL_ALT0>;
 218                         };
 219                         pcm_gpio28: pcm_gpio28 {
 220                                 brcm,pins = <28 29 30 31>;
 221                                 brcm,function = <BCM2835_FSEL_ALT2>;
 222                         };
 223
 224                         sdhost_gpio48: sdhost_gpio48 {
 225                                 brcm,pins = <48 49 50 51 52 53>;
 226                                 brcm,function = <BCM2835_FSEL_ALT0>;
 227                         };
 228
 229                         spi0_gpio7: spi0_gpio7 {
 230                                 brcm,pins = <7 8 9 10 11>;
 231                                 brcm,function = <BCM2835_FSEL_ALT0>;
 232                         };
 233                         spi0_gpio35: spi0_gpio35 {
 234                                 brcm,pins = <35 36 37 38 39>;
 235                                 brcm,function = <BCM2835_FSEL_ALT0>;
 236                         };
 237                         spi1_gpio16: spi1_gpio16 {
 238                                 brcm,pins = <16 17 18 19 20 21>;
 239                                 brcm,function = <BCM2835_FSEL_ALT4>;
 240                         };
 241                         spi2_gpio40: spi2_gpio40 {
 242                                 brcm,pins = <40 41 42 43 44 45>;
 243                                 brcm,function = <BCM2835_FSEL_ALT4>;
 244                         };
 245
 246                         uart0_gpio14: uart0_gpio14 {
 247                                 brcm,pins = <14 15>;
 248                                 brcm,function = <BCM2835_FSEL_ALT0>;
 249                         };
 250                         /* Separate from the uart0_gpio14 group
 251                          * because it conflicts with spi1_gpio16, and
 252                          * people often run uart0 on the two pins
 253                          * without flow control.
 254                          */
 255                         uart0_ctsrts_gpio16: uart0_ctsrts_gpio16 {
 256                                 brcm,pins = <16 17>;
 257                                 brcm,function = <BCM2835_FSEL_ALT3>;
 258                         };
 259                         uart0_ctsrts_gpio30: uart0_ctsrts_gpio30 {
 260                                 brcm,pins = <30 31>;
 261                                 brcm,function = <BCM2835_FSEL_ALT3>;
 262                                 brcm,pull = <BCM2835_PUD_UP BCM2835_PUD_OFF>;
 263                         };
 264                         uart0_gpio32: uart0_gpio32 {
 265                                 brcm,pins = <32 33>;
 266                                 brcm,function = <BCM2835_FSEL_ALT3>;
 267                                 brcm,pull = <BCM2835_PUD_OFF BCM2835_PUD_UP>;
 268                         };
 269                         uart0_gpio36: uart0_gpio36 {
 270                                 brcm,pins = <36 37>;
 271                                 brcm,function = <BCM2835_FSEL_ALT2>;
 272                         };
 273                         uart0_ctsrts_gpio38: uart0_ctsrts_gpio38 {
 274                                 brcm,pins = <38 39>;
 275                                 brcm,function = <BCM2835_FSEL_ALT2>;
 276                         };
 277
 278                         uart1_gpio14: uart1_gpio14 {
 279                                 brcm,pins = <14 15>;
 280                                 brcm,function = <BCM2835_FSEL_ALT5>;
 281                         };
 282                         uart1_ctsrts_gpio16: uart1_ctsrts_gpio16 {
 283                                 brcm,pins = <16 17>;
 284                                 brcm,function = <BCM2835_FSEL_ALT5>;
 285                         };
 286                         uart1_gpio32: uart1_gpio32 {
 287                                 brcm,pins = <32 33>;
 288                                 brcm,function = <BCM2835_FSEL_ALT5>;
 289                         };
 290                         uart1_ctsrts_gpio30: uart1_ctsrts_gpio30 {
 291                                 brcm,pins = <30 31>;
 292                                 brcm,function = <BCM2835_FSEL_ALT5>;
 293                         };
 294                         uart1_gpio40: uart1_gpio40 {
 295                                 brcm,pins = <40 41>;
 296                                 brcm,function = <BCM2835_FSEL_ALT5>;
 297                         };
 298                         uart1_ctsrts_gpio42: uart1_ctsrts_gpio42 {
 299                                 brcm,pins = <42 43>;
 300                                 brcm,function = <BCM2835_FSEL_ALT5>;
 301                         };
 302                 };
 303
 304                 uart0: serial@7e201000 {
 305                         compatible = "arm,pl011", "arm,primecell";
 306                         reg = <0x7e201000 0x200>;
 307                         interrupts = <2 25>;
 308                         clocks = <&clocks BCM2835_CLOCK_UART>,
 309                                  <&clocks BCM2835_CLOCK_VPU>;
 310                         clock-names = "uartclk", "apb_pclk";
 311                         arm,primecell-periphid = <0x00241011>;
 312                 };
 313
 314                 sdhost: mmc@7e202000 {
 315                         compatible = "brcm,bcm2835-sdhost";
 316                         reg = <0x7e202000 0x100>;
 317                         interrupts = <2 24>;
 318                         clocks = <&clocks BCM2835_CLOCK_VPU>;
 319                         status = "disabled";
 320                 };
 321
 322                 i2s: i2s@7e203000 {
 323                         compatible = "brcm,bcm2835-i2s";
 324                         reg = <0x7e203000 0x24>;
 325                         clocks = <&clocks BCM2835_CLOCK_PCM>;
 326                         status = "disabled";
 327                 };
 328
 329                 spi: spi@7e204000 {
 330                         compatible = "brcm,bcm2835-spi";
 331                         reg = <0x7e204000 0x200>;
 332                         interrupts = <2 22>;
 333                         clocks = <&clocks BCM2835_CLOCK_VPU>;
 334                         #address-cells = <1>;
 335                         #size-cells = <0>;
 336                         status = "disabled";
 337                 };
 338
 339                 i2c0: i2c@7e205000 {
 340                         compatible = "brcm,bcm2835-i2c";
 341                         reg = <0x7e205000 0x200>;
 342                         interrupts = <2 21>;
 343                         clocks = <&clocks BCM2835_CLOCK_VPU>;
 344                         #address-cells = <1>;
 345                         #size-cells = <0>;
 346                         status = "disabled";
 347                 };
 348
 349                 dpi: dpi@7e208000 {
 350                         compatible = "brcm,bcm2835-dpi";
 351                         reg = <0x7e208000 0x8c>;
 352                         clocks = <&clocks BCM2835_CLOCK_VPU>,
 353                                  <&clocks BCM2835_CLOCK_DPI>;
 354                         clock-names = "core", "pixel";
 355                         #address-cells = <1>;
 356                         #size-cells = <0>;
 357                         status = "disabled";
 358                 };
 359
 360                 dsi0: dsi@7e209000 {
 361                         compatible = "brcm,bcm2835-dsi0";
 362                         reg = <0x7e209000 0x78>;
 363                         interrupts = <2 4>;
 364                         #address-cells = <1>;
 365                         #size-cells = <0>;
 366                         #clock-cells = <1>;
 367
 368                         clocks = <&clocks BCM2835_PLLA_DSI0>,
 369                                  <&clocks BCM2835_CLOCK_DSI0E>,
 370                                  <&clocks BCM2835_CLOCK_DSI0P>;
 371                         clock-names = "phy", "escape", "pixel";
 372
 373                         clock-output-names = "dsi0_byte",
 374                                              "dsi0_ddr2",
 375                                              "dsi0_ddr";
 376
 377                         status = "disabled";
 378                 };
 379
 380                 aux: aux@7e215000 {
 381                         compatible = "brcm,bcm2835-aux";
 382                         #clock-cells = <1>;
 383                         reg = <0x7e215000 0x8>;
 384                         clocks = <&clocks BCM2835_CLOCK_VPU>;
 385                 };
 386
 387                 uart1: serial@7e215040 {
 388                         compatible = "brcm,bcm2835-aux-uart";
 389                         reg = <0x7e215040 0x40>;
 390                         interrupts = <1 29>;
 391                         clocks = <&aux BCM2835_AUX_CLOCK_UART>;
 392                         status = "disabled";
 393                 };
 394
 395                 spi1: spi@7e215080 {
 396                         compatible = "brcm,bcm2835-aux-spi";
 397                         reg = <0x7e215080 0x40>;
 398                         interrupts = <1 29>;
 399                         clocks = <&aux BCM2835_AUX_CLOCK_SPI1>;
 400                         #address-cells = <1>;
 401                         #size-cells = <0>;
 402                         status = "disabled";
 403                 };
 404
 405                 spi2: spi@7e2150c0 {
 406                         compatible = "brcm,bcm2835-aux-spi";
 407                         reg = <0x7e2150c0 0x40>;
 408                         interrupts = <1 29>;
 409                         clocks = <&aux BCM2835_AUX_CLOCK_SPI2>;
 410                         #address-cells = <1>;
 411                         #size-cells = <0>;
 412                         status = "disabled";
 413                 };
 414
 415                 pwm: pwm@7e20c000 {
 416                         compatible = "brcm,bcm2835-pwm";
 417                         reg = <0x7e20c000 0x28>;
 418                         clocks = <&clocks BCM2835_CLOCK_PWM>;
 419                         assigned-clocks = <&clocks BCM2835_CLOCK_PWM>;
 420                         assigned-clock-rates = <10000000>;
 421                         #pwm-cells = <2>;
 422                         status = "disabled";
 423                 };
 424
 425                 sdhci: mmc@7e300000 {
 426                         compatible = "brcm,bcm2835-sdhci";
 427                         reg = <0x7e300000 0x100>;
 428                         interrupts = <2 30>;
 429                         clocks = <&clocks BCM2835_CLOCK_EMMC>;
 430                         status = "disabled";
 431                 };
 432
 433                 hvs@7e400000 {
 434                         compatible = "brcm,bcm2835-hvs";
 435                         reg = <0x7e400000 0x6000>;
 436                         interrupts = <2 1>;
 437                 };
 438
 439                 dsi1: dsi@7e700000 {
 440                         compatible = "brcm,bcm2835-dsi1";
 441                         reg = <0x7e700000 0x8c>;
 442                         interrupts = <2 12>;
 443                         #address-cells = <1>;
 444                         #size-cells = <0>;
 445                         #clock-cells = <1>;
 446
 447                         clocks = <&clocks BCM2835_PLLD_DSI1>,
 448                                  <&clocks BCM2835_CLOCK_DSI1E>,
 449                                  <&clocks BCM2835_CLOCK_DSI1P>;
 450                         clock-names = "phy", "escape", "pixel";
 451
 452                         clock-output-names = "dsi1_byte",
 453                                              "dsi1_ddr2",
 454                                              "dsi1_ddr";
 455
 456                         status = "disabled";
 457                 };
 458
 459                 i2c1: i2c@7e804000 {
 460                         compatible = "brcm,bcm2835-i2c";
 461                         reg = <0x7e804000 0x1000>;
 462                         interrupts = <2 21>;
 463                         clocks = <&clocks BCM2835_CLOCK_VPU>;
 464                         #address-cells = <1>;
 465                         #size-cells = <0>;
 466                         status = "disabled";
 467                 };
 468
 469                 usb: usb@7e980000 {
 470                         compatible = "brcm,bcm2835-usb";
 471                         reg = <0x7e980000 0x10000>;
 472                         interrupts = <1 9>;
 473                         #address-cells = <1>;
 474                         #size-cells = <0>;
 475                         clocks = <&clk_usb>;
 476                         clock-names = "otg";
 477                         phys = <&usbphy>;
 478                         phy-names = "usb2-phy";
 479                 };
 480         };
 481
 482         clocks {
 483                 /* The oscillator is the root of the clock tree. */
 484                 clk_osc: clk-osc {
 485                         compatible = "fixed-clock";
 486                         #clock-cells = <0>;
 487                         clock-output-names = "osc";
 488                         clock-frequency = <19200000>;
 489                 };
 490
 491                 clk_usb: clk-usb {
 492                         compatible = "fixed-clock";
 493                         #clock-cells = <0>;
 494                         clock-output-names = "otg";
 495                         clock-frequency = <480000000>;
 496                 };
 497         };
 498
 499         usbphy: phy {
 500                 compatible = "usb-nop-xceiv";
 501                 #phy-cells = <0>;
 502         };
 503 };