arch/arm/boot/dts/aspeed-bmc-facebook-bletchley.dts

   1 // SPDX-License-Identifier: GPL-2.0+
   2 // Copyright (c) 2021 Facebook Inc.
   3 /dts-v1/;
   4
   5 #include "aspeed-g6.dtsi"
   6 #include <dt-bindings/gpio/aspeed-gpio.h>
   7 #include <dt-bindings/usb/pd.h>
   8 #include <dt-bindings/leds/leds-pca955x.h>
   9 #include <dt-bindings/interrupt-controller/irq.h>
  10 #include <dt-bindings/i2c/i2c.h>
  11
  12 / {
  13         model = "Facebook Bletchley BMC";
  14         compatible = "facebook,bletchley-bmc", "aspeed,ast2600";
  15
  16         aliases {
  17                 serial4 = &uart5;
  18         };
  19
  20         chosen {
  21                 bootargs = "console=ttyS4,57600n8";
  22         };
  23
  24         memory@80000000 {
  25                 device_type = "memory";
  26                 reg = <0x80000000 0x80000000>;
  27         };
  28
  29         iio-hwmon {
  30                 compatible = "iio-hwmon";
  31                 io-channels = <&adc0 0>, <&adc0 1>, <&adc0 2>, <&adc0 3>,
  32                         <&adc0 4>, <&adc0 5>, <&adc0 6>, <&adc0 7>,
  33                         <&adc1 0>, <&adc1 1>, <&adc1 2>, <&adc1 3>,
  34                         <&adc1 4>, <&adc1 5>, <&adc1 6>, <&adc1 7>;
  35         };
  36
  37         spi1_gpio: spi1-gpio {
  38                 compatible = "spi-gpio";
  39                 #address-cells = <1>;
  40                 #size-cells = <0>;
  41
  42                 gpio-sck = <&gpio0 ASPEED_GPIO(Z, 3) GPIO_ACTIVE_HIGH>;
  43                 gpio-mosi = <&gpio0 ASPEED_GPIO(Z, 4) GPIO_ACTIVE_HIGH>;
  44                 gpio-miso = <&gpio0 ASPEED_GPIO(Z, 5) GPIO_ACTIVE_HIGH>;
  45                 num-chipselects = <1>;
  46                 cs-gpios = <&gpio0 ASPEED_GPIO(Z, 0) GPIO_ACTIVE_LOW>;
  47
  48                 tpmdev@0 {
  49                         compatible = "tcg,tpm_tis-spi";
  50                         spi-max-frequency = <33000000>;
  51                         reg = <0>;
  52                 };
  53         };
  54
  55         switchphy: ethernet-phy@0 {
  56                 // Fixed link
  57         };
  58
  59         front_gpio_leds {
  60                 compatible = "gpio-leds";
  61                 sys_log_id {
  62                         default-state = "off";
  63                         gpios = <&front_leds 0 GPIO_ACTIVE_HIGH>;
  64                 };
  65         };
  66
  67         fan_gpio_leds {
  68                 compatible = "gpio-leds";
  69                 fan0_blue {
  70                         retain-state-shutdown;
  71                         default-state = "on";
  72                         gpios = <&fan_leds 8 GPIO_ACTIVE_HIGH>;
  73                 };
  74                 fan1_blue {
  75                         retain-state-shutdown;
  76                         default-state = "on";
  77                         gpios = <&fan_leds 9 GPIO_ACTIVE_HIGH>;
  78                 };
  79                 fan2_blue {
  80                         retain-state-shutdown;
  81                         default-state = "on";
  82                         gpios = <&fan_leds 10 GPIO_ACTIVE_HIGH>;
  83                 };
  84                 fan3_blue {
  85                         retain-state-shutdown;
  86                         default-state = "on";
  87                         gpios = <&fan_leds 11 GPIO_ACTIVE_HIGH>;
  88                 };
  89                 fan0_amber {
  90                         retain-state-shutdown;
  91                         default-state = "off";
  92                         gpios = <&fan_leds 12 GPIO_ACTIVE_HIGH>;
  93                 };
  94                 fan1_amber {
  95                         retain-state-shutdown;
  96                         default-state = "off";
  97                         gpios = <&fan_leds 13 GPIO_ACTIVE_HIGH>;
  98                 };
  99                 fan2_amber {
 100                         retain-state-shutdown;
 101                         default-state = "off";
 102                         gpios = <&fan_leds 14 GPIO_ACTIVE_HIGH>;
 103                 };
 104                 fan3_amber {
 105                         retain-state-shutdown;
 106                         default-state = "off";
 107                         gpios = <&fan_leds 15 GPIO_ACTIVE_HIGH>;
 108                 };
 109         };
 110
 111         sled1_gpio_leds {
 112                 compatible = "gpio-leds";
 113                 sled1_amber {
 114                         retain-state-shutdown;
 115                         default-state = "keep";
 116                         gpios = <&sled1_leds 0 GPIO_ACTIVE_LOW>;
 117                 };
 118                 sled1_blue {
 119                         retain-state-shutdown;
 120                         default-state = "keep";
 121                         gpios = <&sled1_leds 1 GPIO_ACTIVE_LOW>;
 122                 };
 123         };
 124
 125         sled2_gpio_leds {
 126                 compatible = "gpio-leds";
 127                 sled2_amber {
 128                         retain-state-shutdown;
 129                         default-state = "keep";
 130                         gpios = <&sled2_leds 0 GPIO_ACTIVE_LOW>;
 131                 };
 132                 sled2_blue {
 133                         retain-state-shutdown;
 134                         default-state = "keep";
 135                         gpios = <&sled2_leds 1 GPIO_ACTIVE_LOW>;
 136                 };
 137         };
 138
 139         sled3_gpio_leds {
 140                 compatible = "gpio-leds";
 141                 sled3_amber {
 142                         retain-state-shutdown;
 143                         default-state = "keep";
 144                         gpios = <&sled3_leds 0 GPIO_ACTIVE_LOW>;
 145                 };
 146                 sled3_blue {
 147                         retain-state-shutdown;
 148                         default-state = "keep";
 149                         gpios = <&sled3_leds 1 GPIO_ACTIVE_LOW>;
 150                 };
 151         };
 152
 153         sled4_gpio_leds {
 154                 compatible = "gpio-leds";
 155                 sled4_amber {
 156                         retain-state-shutdown;
 157                         default-state = "keep";
 158                         gpios = <&sled4_leds 0 GPIO_ACTIVE_LOW>;
 159                 };
 160                 sled4_blue {
 161                         retain-state-shutdown;
 162                         default-state = "keep";
 163                         gpios = <&sled4_leds 1 GPIO_ACTIVE_LOW>;
 164                 };
 165         };
 166
 167         sled5_gpio_leds {
 168                 compatible = "gpio-leds";
 169                 sled5_amber {
 170                         retain-state-shutdown;
 171                         default-state = "keep";
 172                         gpios = <&sled5_leds 0 GPIO_ACTIVE_LOW>;
 173                 };
 174                 sled5_blue {
 175                         retain-state-shutdown;
 176                         default-state = "keep";
 177                         gpios = <&sled5_leds 1 GPIO_ACTIVE_LOW>;
 178                 };
 179         };
 180
 181         sled6_gpio_leds {
 182                 compatible = "gpio-leds";
 183                 sled6_amber {
 184                         retain-state-shutdown;
 185                         default-state = "keep";
 186                         gpios = <&sled6_leds 0 GPIO_ACTIVE_LOW>;
 187                 };
 188                 sled6_blue {
 189                         retain-state-shutdown;
 190                         default-state = "keep";
 191                         gpios = <&sled6_leds 1 GPIO_ACTIVE_LOW>;
 192                 };
 193         };
 194 };
 195
 196 &mac2 {
 197         status = "okay";
 198         phy-mode = "rgmii";
 199         phy-handle = <&switchphy>;
 200         pinctrl-names = "default";
 201         pinctrl-0 = <&pinctrl_rgmii3_default>;
 202
 203         fixed-link {
 204                 speed = <1000>;
 205                 full-duplex;
 206         };
 207 };
 208
 209 &fmc {
 210         status = "okay";
 211         flash@0 {
 212                 status = "okay";
 213                 m25p,fast-read;
 214                 label = "bmc";
 215                 spi-max-frequency = <50000000>;
 216 #include "openbmc-flash-layout-128.dtsi"
 217         };
 218         flash@1 {
 219                 status = "okay";
 220                 m25p,fast-read;
 221                 label = "flash1";
 222                 spi-max-frequency = <50000000>;
 223         };
 224 };
 225
 226 &spi2 {
 227         status = "okay";
 228         pinctrl-names = "default";
 229         pinctrl-0 = <&pinctrl_spi2_default>;
 230
 231         flash@0 {
 232                 status = "okay";
 233                 m25p,fast-read;
 234                 label = "pnor";
 235                 spi-max-frequency = <50000000>;
 236         };
 237 };
 238
 239 &i2c0 {
 240         status = "okay";
 241         ina230@45 {
 242                 compatible = "ti,ina230";
 243                 reg = <0x45>;
 244                 shunt-resistor = <2000>;
 245         };
 246
 247         mp5023@40 {
 248                 compatible = "mps,mp5023";
 249                 reg = <0x40>;
 250         };
 251
 252         tmp421@4f {
 253                 compatible = "ti,tmp421";
 254                 reg = <0x4f>;
 255         };
 256
 257         sled1_ioexp41: pca9536@41 {
 258                 compatible = "nxp,pca9536";
 259                 reg = <0x41>;
 260                 gpio-controller;
 261                 #gpio-cells = <2>;
 262
 263                 gpio-line-names =
 264                 "SLED1_SWD_MUX", "SLED1_XRES_SWD_N",
 265                 "SLED1_CLKREQ_N", "SLED1_PCIE_PWR_EN";
 266         };
 267
 268         sled1_ioexp: pca9539@76 {
 269                 compatible = "nxp,pca9539";
 270                 reg = <0x76>;
 271                 #address-cells = <1>;
 272                 #size-cells = <0>;
 273                 gpio-controller;
 274                 #gpio-cells = <2>;
 275
 276                 interrupt-parent = <&gpio0>;
 277                 interrupts = <ASPEED_GPIO(M, 0) IRQ_TYPE_LEVEL_LOW>;
 278
 279                 gpio-line-names =
 280                 "SLED1_MS_DETECT1","SLED1_VBUS_BMC_EN","SLED1_INA230_ALERT","SLED1_P12V_STBY_ALERT",
 281                 "SLED1_SSD_ALERT","SLED1_MS_DETECT0","SLED1_RST_CCG5","SLED1_FUSB302_INT",
 282                 "SLED1_MD_STBY_RESET","SLED1_MD_IOEXP_EN_FAULT","SLED1_MD_DIR","SLED1_MD_DECAY",
 283                 "SLED1_MD_MODE1","SLED1_MD_MODE2","SLED1_MD_MODE3","power-host1";
 284         };
 285
 286         sled1_leds: pca9552@67 {
 287                 compatible = "nxp,pca9552";
 288                 reg = <0x67>;
 289                 #address-cells = <1>;
 290                 #size-cells = <0>;
 291                 gpio-controller;
 292                 #gpio-cells = <2>;
 293
 294                 gpio-line-names =
 295                 "led-sled1-amber","led-sled1-blue","SLED1_RST_IOEXP","SLED1_MD_REF_PWM",
 296                 "","","","",
 297                 "","","","",
 298                 "","","","";
 299         };
 300
 301         sled1_fusb302: typec-portc@22 {
 302                 compatible = "fcs,fusb302";
 303                 reg = <0x22>;
 304
 305                 connector {
 306                         compatible = "usb-c-connector";
 307                         label = "USB-C";
 308                         power-role = "dual";
 309                         try-power-role = "sink";
 310                         data-role = "dual";
 311                         source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
 312                         sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
 313                                         PDO_VAR(3000, 12000, 3000)
 314                                         PDO_PPS_APDO(3000, 11000, 3000)>;
 315                         op-sink-microwatt = <10000000>;
 316                 };
 317         };
 318
 319         eeprom@54 {
 320                 compatible = "atmel,24c64";
 321                 reg = <0x54>;
 322         };
 323 };
 324
 325 &i2c1 {
 326         status = "okay";
 327         ina230@45 {
 328                 compatible = "ti,ina230";
 329                 reg = <0x45>;
 330                 shunt-resistor = <2000>;
 331         };
 332
 333         mp5023@40 {
 334                 compatible = "mps,mp5023";
 335                 reg = <0x40>;
 336         };
 337
 338         tmp421@4f {
 339                 compatible = "ti,tmp421";
 340                 reg = <0x4f>;
 341         };
 342
 343         sled2_ioexp41: pca9536@41 {
 344                 compatible = "nxp,pca9536";
 345                 reg = <0x41>;
 346                 gpio-controller;
 347                 #gpio-cells = <2>;
 348
 349                 gpio-line-names =
 350                 "SLED2_SWD_MUX", "SLED2_XRES_SWD_N",
 351                 "SLED2_CLKREQ_N", "SLED2_PCIE_PWR_EN";
 352         };
 353
 354         sled2_ioexp: pca9539@76 {
 355                 compatible = "nxp,pca9539";
 356                 reg = <0x76>;
 357                 #address-cells = <1>;
 358                 #size-cells = <0>;
 359                 gpio-controller;
 360                 #gpio-cells = <2>;
 361
 362                 interrupt-parent = <&gpio0>;
 363                 interrupts = <ASPEED_GPIO(M, 1) IRQ_TYPE_LEVEL_LOW>;
 364
 365                 gpio-line-names =
 366                 "SLED2_MS_DETECT1","SLED2_VBUS_BMC_EN","SLED2_INA230_ALERT","SLED2_P12V_STBY_ALERT",
 367                 "SLED2_SSD_ALERT","SLED2_MS_DETECT0","SLED2_RST_CCG5","SLED2_FUSB302_INT",
 368                 "SLED2_MD_STBY_RESET","SLED2_MD_IOEXP_EN_FAULT","SLED2_MD_DIR","SLED2_MD_DECAY",
 369                 "SLED2_MD_MODE1","SLED2_MD_MODE2","SLED2_MD_MODE3","power-host2";
 370         };
 371
 372         sled2_leds: pca9552@67 {
 373                 compatible = "nxp,pca9552";
 374                 reg = <0x67>;
 375                 #address-cells = <1>;
 376                 #size-cells = <0>;
 377                 gpio-controller;
 378                 #gpio-cells = <2>;
 379
 380                 gpio-line-names =
 381                 "led-sled2-amber","led-sled2-blue","SLED2_RST_IOEXP","SLED2_MD_REF_PWM",
 382                 "","","","",
 383                 "","","","",
 384                 "","","","";
 385         };
 386
 387         sled2_fusb302: typec-portc@22 {
 388                 compatible = "fcs,fusb302";
 389                 reg = <0x22>;
 390
 391                 connector {
 392                         compatible = "usb-c-connector";
 393                         label = "USB-C";
 394                         power-role = "dual";
 395                         try-power-role = "sink";
 396                         data-role = "dual";
 397                         source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
 398                         sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
 399                                         PDO_VAR(3000, 12000, 3000)
 400                                         PDO_PPS_APDO(3000, 11000, 3000)>;
 401                         op-sink-microwatt = <10000000>;
 402                 };
 403         };
 404
 405         eeprom@54 {
 406                 compatible = "atmel,24c64";
 407                 reg = <0x54>;
 408         };
 409 };
 410
 411 &i2c2 {
 412         status = "okay";
 413         ina230@45 {
 414                 compatible = "ti,ina230";
 415                 reg = <0x45>;
 416                 shunt-resistor = <2000>;
 417         };
 418
 419         mp5023@40 {
 420                 compatible = "mps,mp5023";
 421                 reg = <0x40>;
 422         };
 423
 424         tmp421@4f {
 425                 compatible = "ti,tmp421";
 426                 reg = <0x4f>;
 427         };
 428
 429         sled3_ioexp41: pca9536@41 {
 430                 compatible = "nxp,pca9536";
 431                 reg = <0x41>;
 432                 gpio-controller;
 433                 #gpio-cells = <2>;
 434
 435                 gpio-line-names =
 436                 "SLED3_SWD_MUX", "SLED3_XRES_SWD_N",
 437                 "SLED3_CLKREQ_N", "SLED3_PCIE_PWR_EN";
 438         };
 439
 440         sled3_ioexp: pca9539@76 {
 441                 compatible = "nxp,pca9539";
 442                 reg = <0x76>;
 443                 #address-cells = <1>;
 444                 #size-cells = <0>;
 445                 gpio-controller;
 446                 #gpio-cells = <2>;
 447
 448                 interrupt-parent = <&gpio0>;
 449                 interrupts = <ASPEED_GPIO(M, 2) IRQ_TYPE_LEVEL_LOW>;
 450
 451                 gpio-line-names =
 452                 "SLED3_MS_DETECT1","SLED3_VBUS_BMC_EN","SLED3_INA230_ALERT","SLED3_P12V_STBY_ALERT",
 453                 "SLED3_SSD_ALERT","SLED3_MS_DETECT0","SLED3_RST_CCG5","SLED3_FUSB302_INT",
 454                 "SLED3_MD_STBY_RESET","SLED3_MD_IOEXP_EN_FAULT","SLED3_MD_DIR","SLED3_MD_DECAY",
 455                 "SLED3_MD_MODE1","SLED3_MD_MODE2","SLED3_MD_MODE3","power-host3";
 456         };
 457
 458         sled3_leds: pca9552@67 {
 459                 compatible = "nxp,pca9552";
 460                 reg = <0x67>;
 461                 #address-cells = <1>;
 462                 #size-cells = <0>;
 463                 gpio-controller;
 464                 #gpio-cells = <2>;
 465
 466                 gpio-line-names =
 467                 "led-sled3-amber","led-sled3-blue","SLED3_RST_IOEXP","SLED3_MD_REF_PWM",
 468                 "","","","",
 469                 "","","","",
 470                 "","","","";
 471         };
 472
 473         sled3_fusb302: typec-portc@22 {
 474                 compatible = "fcs,fusb302";
 475                 reg = <0x22>;
 476
 477                 connector {
 478                         compatible = "usb-c-connector";
 479                         label = "USB-C";
 480                         power-role = "dual";
 481                         try-power-role = "sink";
 482                         data-role = "dual";
 483                         source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
 484                         sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
 485                                         PDO_VAR(3000, 12000, 3000)
 486                                         PDO_PPS_APDO(3000, 11000, 3000)>;
 487                         op-sink-microwatt = <10000000>;
 488                 };
 489         };
 490
 491         eeprom@54 {
 492                 compatible = "atmel,24c64";
 493                 reg = <0x54>;
 494         };
 495 };
 496
 497 &i2c3 {
 498         status = "okay";
 499         ina230@45 {
 500                 compatible = "ti,ina230";
 501                 reg = <0x45>;
 502                 shunt-resistor = <2000>;
 503         };
 504
 505         mp5023@40 {
 506                 compatible = "mps,mp5023";
 507                 reg = <0x40>;
 508         };
 509
 510         tmp421@4f {
 511                 compatible = "ti,tmp421";
 512                 reg = <0x4f>;
 513         };
 514
 515         sled4_ioexp41: pca9536@41 {
 516                 compatible = "nxp,pca9536";
 517                 reg = <0x41>;
 518                 gpio-controller;
 519                 #gpio-cells = <2>;
 520
 521                 gpio-line-names =
 522                 "SLED4_SWD_MUX", "SLED4_XRES_SWD_N",
 523                 "SLED4_CLKREQ_N", "SLED4_PCIE_PWR_EN";
 524         };
 525
 526         sled4_ioexp: pca9539@76 {
 527                 compatible = "nxp,pca9539";
 528                 reg = <0x76>;
 529                 #address-cells = <1>;
 530                 #size-cells = <0>;
 531                 gpio-controller;
 532                 #gpio-cells = <2>;
 533
 534                 interrupt-parent = <&gpio0>;
 535                 interrupts = <ASPEED_GPIO(M, 3) IRQ_TYPE_LEVEL_LOW>;
 536
 537                 gpio-line-names =
 538                 "SLED4_MS_DETECT1","SLED4_VBUS_BMC_EN","SLED4_INA230_ALERT","SLED4_P12V_STBY_ALERT",
 539                 "SLED4_SSD_ALERT","SLED4_MS_DETECT0","SLED4_RST_CCG5","SLED4_FUSB302_INT",
 540                 "SLED4_MD_STBY_RESET","SLED4_MD_IOEXP_EN_FAULT","SLED4_MD_DIR","SLED4_MD_DECAY",
 541                 "SLED4_MD_MODE1","SLED4_MD_MODE2","SLED4_MD_MODE3","power-host4";
 542         };
 543
 544         sled4_leds: pca9552@67 {
 545                 compatible = "nxp,pca9552";
 546                 reg = <0x67>;
 547                 #address-cells = <1>;
 548                 #size-cells = <0>;
 549                 gpio-controller;
 550                 #gpio-cells = <2>;
 551
 552                 gpio-line-names =
 553                 "led-sled4-amber","led-sled4-blue","SLED4_RST_IOEXP","SLED4_MD_REF_PWM",
 554                 "","","","",
 555                 "","","","",
 556                 "","","","";
 557         };
 558
 559         sled4_fusb302: typec-portc@22 {
 560                 compatible = "fcs,fusb302";
 561                 reg = <0x22>;
 562
 563                 connector {
 564                         compatible = "usb-c-connector";
 565                         label = "USB-C";
 566                         power-role = "dual";
 567                         try-power-role = "sink";
 568                         data-role = "dual";
 569                         source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
 570                         sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
 571                                         PDO_VAR(3000, 12000, 3000)
 572                                         PDO_PPS_APDO(3000, 11000, 3000)>;
 573                         op-sink-microwatt = <10000000>;
 574                 };
 575         };
 576
 577         eeprom@54 {
 578                 compatible = "atmel,24c64";
 579                 reg = <0x54>;
 580         };
 581 };
 582
 583 &i2c4 {
 584         status = "okay";
 585         ina230@45 {
 586                 compatible = "ti,ina230";
 587                 reg = <0x45>;
 588                 shunt-resistor = <2000>;
 589         };
 590
 591         mp5023@40 {
 592                 compatible = "mps,mp5023";
 593                 reg = <0x40>;
 594         };
 595
 596         tmp421@4f {
 597                 compatible = "ti,tmp421";
 598                 reg = <0x4f>;
 599         };
 600
 601         sled5_ioexp41: pca9536@41 {
 602                 compatible = "nxp,pca9536";
 603                 reg = <0x41>;
 604                 gpio-controller;
 605                 #gpio-cells = <2>;
 606
 607                 gpio-line-names =
 608                 "SLED5_SWD_MUX", "SLED5_XRES_SWD_N",
 609                 "SLED5_CLKREQ_N", "SLED5_PCIE_PWR_EN";
 610         };
 611
 612         sled5_ioexp: pca9539@76 {
 613                 compatible = "nxp,pca9539";
 614                 reg = <0x76>;
 615                 #address-cells = <1>;
 616                 #size-cells = <0>;
 617                 gpio-controller;
 618                 #gpio-cells = <2>;
 619
 620                 interrupt-parent = <&gpio0>;
 621                 interrupts = <ASPEED_GPIO(M, 4) IRQ_TYPE_LEVEL_LOW>;
 622
 623                 gpio-line-names =
 624                 "SLED5_MS_DETECT1","SLED5_VBUS_BMC_EN","SLED5_INA230_ALERT","SLED5_P12V_STBY_ALERT",
 625                 "SLED5_SSD_ALERT","SLED5_MS_DETECT0","SLED5_RST_CCG5","SLED5_FUSB302_INT",
 626                 "SLED5_MD_STBY_RESET","SLED5_MD_IOEXP_EN_FAULT","SLED5_MD_DIR","SLED5_MD_DECAY",
 627                 "SLED5_MD_MODE1","SLED5_MD_MODE2","SLED5_MD_MODE3","power-host5";
 628         };
 629
 630         sled5_leds: pca9552@67 {
 631                 compatible = "nxp,pca9552";
 632                 reg = <0x67>;
 633                 #address-cells = <1>;
 634                 #size-cells = <0>;
 635                 gpio-controller;
 636                 #gpio-cells = <2>;
 637
 638                 gpio-line-names =
 639                 "led-sled5-amber","led-sled5-blue","SLED5_RST_IOEXP","SLED5_MD_REF_PWM",
 640                 "","","","",
 641                 "","","","",
 642                 "","","","";
 643         };
 644
 645         sled5_fusb302: typec-portc@22 {
 646                 compatible = "fcs,fusb302";
 647                 reg = <0x22>;
 648
 649                 connector {
 650                         compatible = "usb-c-connector";
 651                         label = "USB-C";
 652                         power-role = "dual";
 653                         try-power-role = "sink";
 654                         data-role = "dual";
 655                         source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
 656                         sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
 657                                         PDO_VAR(3000, 12000, 3000)
 658                                         PDO_PPS_APDO(3000, 11000, 3000)>;
 659                         op-sink-microwatt = <10000000>;
 660                 };
 661         };
 662
 663         eeprom@54 {
 664                 compatible = "atmel,24c64";
 665                 reg = <0x54>;
 666         };
 667 };
 668
 669 &i2c5 {
 670         status = "okay";
 671         ina230@45 {
 672                 compatible = "ti,ina230";
 673                 reg = <0x45>;
 674                 shunt-resistor = <2000>;
 675         };
 676
 677         mp5023@40 {
 678                 compatible = "mps,mp5023";
 679                 reg = <0x40>;
 680         };
 681
 682         tmp421@4f {
 683                 compatible = "ti,tmp421";
 684                 reg = <0x4f>;
 685         };
 686
 687         sled6_ioexp41: pca9536@41 {
 688                 compatible = "nxp,pca9536";
 689                 reg = <0x41>;
 690                 gpio-controller;
 691                 #gpio-cells = <2>;
 692
 693                 gpio-line-names =
 694                 "SLED6_SWD_MUX", "SLED6_XRES_SWD_N",
 695                 "SLED6_CLKREQ_N", "SLED6_PCIE_PWR_EN";
 696         };
 697
 698         sled6_ioexp: pca9539@76 {
 699                 compatible = "nxp,pca9539";
 700                 reg = <0x76>;
 701                 #address-cells = <1>;
 702                 #size-cells = <0>;
 703                 gpio-controller;
 704                 #gpio-cells = <2>;
 705
 706                 interrupt-parent = <&gpio0>;
 707                 interrupts = <ASPEED_GPIO(M, 5) IRQ_TYPE_LEVEL_LOW>;
 708
 709                 gpio-line-names =
 710                 "SLED6_MS_DETECT1","SLED6_VBUS_BMC_EN","SLED6_INA230_ALERT","SLED6_P12V_STBY_ALERT",
 711                 "SLED6_SSD_ALERT","SLED6_MS_DETECT0","SLED6_RST_CCG5","SLED6_FUSB302_INT",
 712                 "SLED6_MD_STBY_RESET","SLED6_MD_IOEXP_EN_FAULT","SLED6_MD_DIR","SLED6_MD_DECAY",
 713                 "SLED6_MD_MODE1","SLED6_MD_MODE2","SLED6_MD_MODE3","power-host6";
 714         };
 715
 716         sled6_leds: pca9552@67 {
 717                 compatible = "nxp,pca9552";
 718                 reg = <0x67>;
 719                 #address-cells = <1>;
 720                 #size-cells = <0>;
 721                 gpio-controller;
 722                 #gpio-cells = <2>;
 723
 724                 gpio-line-names =
 725                 "led-sled6-amber","led-sled6-blue","SLED6_RST_IOEXP","SLED6_MD_REF_PWM",
 726                 "","","","",
 727                 "","","","",
 728                 "","","","";
 729         };
 730
 731         sled6_fusb302: typec-portc@22 {
 732                 compatible = "fcs,fusb302";
 733                 reg = <0x22>;
 734
 735                 connector {
 736                         compatible = "usb-c-connector";
 737                         label = "USB-C";
 738                         power-role = "dual";
 739                         try-power-role = "sink";
 740                         data-role = "dual";
 741                         source-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
 742                         sink-pdos = <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
 743                                         PDO_VAR(3000, 12000, 3000)
 744                                         PDO_PPS_APDO(3000, 11000, 3000)>;
 745                         op-sink-microwatt = <10000000>;
 746                 };
 747         };
 748
 749         eeprom@54 {
 750                 compatible = "atmel,24c64";
 751                 reg = <0x54>;
 752         };
 753 };
 754
 755 &i2c6 {
 756         status = "okay";
 757
 758         eeprom@56 {
 759                 compatible = "atmel,24c64";
 760                 reg = <0x56>;
 761         };
 762
 763         rtc@51 {
 764                 /* in-chip rtc disabled, use external rtc (battery-backed) */
 765                 compatible = "nxp,pcf85263";
 766                 reg = <0x51>;
 767         };
 768 };
 769
 770 &i2c7 {
 771         status = "okay";
 772
 773         eeprom@54 {
 774                 compatible = "atmel,24c64";
 775                 reg = <0x54>;
 776         };
 777 };
 778
 779 &i2c9 {
 780         status = "okay";
 781
 782         tmp421@4f {
 783                 compatible = "ti,tmp421";
 784                 reg = <0x4f>;
 785         };
 786 };
 787
 788 &i2c10 {
 789         status = "okay";
 790
 791         tmp421@4f {
 792                 compatible = "ti,tmp421";
 793                 reg = <0x4f>;
 794         };
 795
 796         front_leds: pca9552@67 {
 797                 compatible = "nxp,pca9552";
 798                 reg = <0x67>;
 799                 #address-cells = <1>;
 800                 #size-cells = <0>;
 801                 gpio-controller;
 802                 #gpio-cells = <2>;
 803
 804                 gpio-line-names =
 805                 "led-fault-identify","power-p5v-stby-good",
 806                 "power-p1v0-dvdd-good","power-p1v0-avdd-good",
 807                 "","","","",
 808                 "","","","",
 809                 "","","","";
 810         };
 811 };
 812
 813 &i2c12 {
 814         status = "okay";
 815
 816         adm1278@11 {
 817                 compatible = "adi,adm1278";
 818                 reg = <0x11>;
 819                 shunt-resistor-micro-ohms = <300>;
 820                 adi,volt-curr-sample-average = <128>;
 821                 adi,power-sample-average = <128>;
 822         };
 823
 824         tmp421@4c {
 825                 compatible = "ti,tmp421";
 826                 reg = <0x4c>;
 827         };
 828
 829         tmp421@4d {
 830                 compatible = "ti,tmp421";
 831                 reg = <0x4d>;
 832         };
 833
 834         fan_leds: pca9552@67 {
 835                 compatible = "nxp,pca9552";
 836                 reg = <0x67>;
 837                 #address-cells = <1>;
 838                 #size-cells = <0>;
 839                 gpio-controller;
 840                 #gpio-cells = <2>;
 841
 842                 gpio-line-names =
 843                 "presence-fan0","presence-fan1",
 844                 "presence-fan2","presence-fan3",
 845                 "power-fan0-good","power-fan1-good",
 846                 "power-fan2-good","power-fan3-good",
 847                 "","","","",
 848                 "","","","";
 849         };
 850 };
 851
 852 &i2c13 {
 853         multi-master;
 854         aspeed,hw-timeout-ms = <1000>;
 855         status = "okay";
 856
 857         //USB Debug Connector
 858         ipmb13@10 {
 859                 compatible = "ipmb-dev";
 860                 reg = <(0x10 | I2C_OWN_SLAVE_ADDRESS)>;
 861                 i2c-protocol;
 862         };
 863 };
 864
 865 &gpio0 {
 866         gpio-line-names =
 867         /*A0-A7*/       "","","","","","","","",
 868         /*B0-B7*/       "FUSB302_SLED1_INT_N","FUSB302_SLED2_INT_N",
 869                         "SEL_SPI2_MUX","SPI2_MUX1",
 870                         "SPI2_MUX2","SPI2_MUX3",
 871                         "","FUSB302_SLED3_INT_N",
 872         /*C0-C7*/       "","","","","","","","",
 873         /*D0-D7*/       "","","","","","","","",
 874         /*E0-E7*/       "","","","","","","","",
 875         /*F0-F7*/       "BMC_SLED1_STCK","BMC_SLED2_STCK",
 876                         "BMC_SLED3_STCK","BMC_SLED4_STCK",
 877                         "BMC_SLED5_STCK","BMC_SLED6_STCK",
 878                         "","",
 879         /*G0-G7*/       "BSM_FRU_WP","SWITCH_FRU_MUX","","FM_SOL_UART_CH_SEL",
 880                         "PWRGD_P1V05_VDDCORE","PWRGD_P1V5_VDD","","",
 881         /*H0-H7*/       "presence-riser1","presence-riser2",
 882                         "presence-sled1","presence-sled2",
 883                         "presence-sled3","presence-sled4",
 884                         "presence-sled5","presence-sled6",
 885         /*I0-I7*/       "REV_ID0","",
 886                         "REV_ID1","REV_ID2",
 887                         "","BSM_FLASH_WP_STATUS",
 888                         "BMC_TPM_PRES_N","FUSB302_SLED6_INT_N",
 889         /*J0-J7*/       "","","","","","","","",
 890         /*K0-K7*/       "","","","","","","","",
 891         /*L0-L7*/       "","","","","","BMC_RTC_INT","","",
 892         /*M0-M7*/       "ALERT_SLED1_N","ALERT_SLED2_N",
 893                         "ALERT_SLED3_N","ALERT_SLED4_N",
 894                         "ALERT_SLED5_N","ALERT_SLED6_N",
 895                         "","",
 896         /*N0-N7*/       "LED_POSTCODE_0","LED_POSTCODE_1",
 897                         "LED_POSTCODE_2","LED_POSTCODE_3",
 898                         "LED_POSTCODE_4","LED_POSTCODE_5",
 899                         "LED_POSTCODE_5","LED_POSTCODE_7",
 900         /*O0-O7*/       "","","","",
 901                         "","BOARD_ID0","BOARD_ID1","BOARD_ID2",
 902         /*P0-P7*/       "","","","","","","","BMC_HEARTBEAT",
 903         /*Q0-Q7*/       "","","","","","","","",
 904         /*R0-R7*/       "","","","","","","","",
 905         /*S0-S7*/       "","","","BAT_DETECT",
 906                         "BMC_BT_WP0_N","BMC_BT_WP1_N","","FUSB302_SLED4_INT_N",
 907         /*T0-T7*/       "","","","","","","","",
 908         /*U0-U7*/       "","","","","","","","",
 909         /*V0-V7*/       "PWRGD_CNS_PSU","RST_BMC_MVL_N",
 910                         "P12V_AUX_ALERT1_N","PSU_PRSNT",
 911                         "USB2_SEL0_A","USB2_SEL1_A",
 912                         "USB2_SEL0_B","USB2_SEL1_B",
 913         /*W0-W7*/       "RST_FRONT_IOEXP_N","","","","","","","",
 914         /*X0-X7*/       "","","","","","","","",
 915         /*Y0-Y7*/       "BMC_SELF_HW_RST","BSM_PRSNT_N",
 916                         "BSM_FLASH_LATCH_N","FUSB302_SLED5_INT_N",
 917                         "","","","",
 918         /*Z0-Z7*/       "","","","","","","","";
 919 };
 920
 921 &adc0 {
 922         vref = <1800>;
 923         status = "okay";
 924
 925         pinctrl-names = "default";
 926         pinctrl-0 = <&pinctrl_adc0_default &pinctrl_adc1_default
 927                 &pinctrl_adc2_default &pinctrl_adc3_default
 928                 &pinctrl_adc4_default &pinctrl_adc5_default
 929                 &pinctrl_adc6_default &pinctrl_adc7_default>;
 930 };
 931
 932 &adc1 {
 933         vref = <2500>;
 934         status = "okay";
 935
 936         pinctrl-names = "default";
 937         pinctrl-0 = <&pinctrl_adc8_default &pinctrl_adc9_default
 938                 &pinctrl_adc10_default &pinctrl_adc11_default
 939                 &pinctrl_adc12_default &pinctrl_adc13_default
 940                 &pinctrl_adc14_default &pinctrl_adc15_default>;
 941 };
 942
 943 &mdio0 {
 944         status = "okay";
 945         /* TODO: Add Marvell 88E6191X */
 946 };
 947
 948 &mdio3 {
 949         status = "okay";
 950         /* TODO: Add Marvell 88X3310 */
 951 };
 952
 953 &ehci0 {
 954         status = "okay";
 955 };