1 // SPDX-License-Identifier: GPL-2.0-or-later
3 * A sensor driver for the magnetometer AK8975.
5 * Magnetic compass sensor driver for monitoring magnetic flux information.
7 * Copyright (c) 2010, NVIDIA Corporation.
10 #include <linux/module.h>
11 #include <linux/mod_devicetable.h>
12 #include <linux/kernel.h>
13 #include <linux/slab.h>
14 #include <linux/i2c.h>
15 #include <linux/interrupt.h>
16 #include <linux/err.h>
17 #include <linux/mutex.h>
18 #include <linux/delay.h>
19 #include <linux/bitops.h>
20 #include <linux/gpio/consumer.h>
21 #include <linux/regulator/consumer.h>
22 #include <linux/pm_runtime.h>
24 #include <linux/iio/iio.h>
25 #include <linux/iio/sysfs.h>
26 #include <linux/iio/buffer.h>
27 #include <linux/iio/trigger.h>
28 #include <linux/iio/trigger_consumer.h>
29 #include <linux/iio/triggered_buffer.h>
32 * Register definitions, as well as various shifts and masks to get at the
33 * individual fields of the registers.
35 #define AK8975_REG_WIA 0x00
36 #define AK8975_DEVICE_ID 0x48
38 #define AK8975_REG_INFO 0x01
40 #define AK8975_REG_ST1 0x02
41 #define AK8975_REG_ST1_DRDY_SHIFT 0
42 #define AK8975_REG_ST1_DRDY_MASK (1 << AK8975_REG_ST1_DRDY_SHIFT)
44 #define AK8975_REG_HXL 0x03
45 #define AK8975_REG_HXH 0x04
46 #define AK8975_REG_HYL 0x05
47 #define AK8975_REG_HYH 0x06
48 #define AK8975_REG_HZL 0x07
49 #define AK8975_REG_HZH 0x08
50 #define AK8975_REG_ST2 0x09
51 #define AK8975_REG_ST2_DERR_SHIFT 2
52 #define AK8975_REG_ST2_DERR_MASK (1 << AK8975_REG_ST2_DERR_SHIFT)
54 #define AK8975_REG_ST2_HOFL_SHIFT 3
55 #define AK8975_REG_ST2_HOFL_MASK (1 << AK8975_REG_ST2_HOFL_SHIFT)
57 #define AK8975_REG_CNTL 0x0A
58 #define AK8975_REG_CNTL_MODE_SHIFT 0
59 #define AK8975_REG_CNTL_MODE_MASK (0xF << AK8975_REG_CNTL_MODE_SHIFT)
60 #define AK8975_REG_CNTL_MODE_POWER_DOWN 0x00
61 #define AK8975_REG_CNTL_MODE_ONCE 0x01
62 #define AK8975_REG_CNTL_MODE_SELF_TEST 0x08
63 #define AK8975_REG_CNTL_MODE_FUSE_ROM 0x0F
65 #define AK8975_REG_RSVC 0x0B
66 #define AK8975_REG_ASTC 0x0C
67 #define AK8975_REG_TS1 0x0D
68 #define AK8975_REG_TS2 0x0E
69 #define AK8975_REG_I2CDIS 0x0F
70 #define AK8975_REG_ASAX 0x10
71 #define AK8975_REG_ASAY 0x11
72 #define AK8975_REG_ASAZ 0x12
74 #define AK8975_MAX_REGS AK8975_REG_ASAZ
77 * AK09912 Register definitions
79 #define AK09912_REG_WIA1 0x00
80 #define AK09912_REG_WIA2 0x01
81 #define AK09916_DEVICE_ID 0x09
82 #define AK09912_DEVICE_ID 0x04
83 #define AK09911_DEVICE_ID 0x05
85 #define AK09911_REG_INFO1 0x02
86 #define AK09911_REG_INFO2 0x03
88 #define AK09912_REG_ST1 0x10
90 #define AK09912_REG_ST1_DRDY_SHIFT 0
91 #define AK09912_REG_ST1_DRDY_MASK (1 << AK09912_REG_ST1_DRDY_SHIFT)
93 #define AK09912_REG_HXL 0x11
94 #define AK09912_REG_HXH 0x12
95 #define AK09912_REG_HYL 0x13
96 #define AK09912_REG_HYH 0x14
97 #define AK09912_REG_HZL 0x15
98 #define AK09912_REG_HZH 0x16
99 #define AK09912_REG_TMPS 0x17
101 #define AK09912_REG_ST2 0x18
102 #define AK09912_REG_ST2_HOFL_SHIFT 3
103 #define AK09912_REG_ST2_HOFL_MASK (1 << AK09912_REG_ST2_HOFL_SHIFT)
105 #define AK09912_REG_CNTL1 0x30
107 #define AK09912_REG_CNTL2 0x31
108 #define AK09912_REG_CNTL_MODE_POWER_DOWN 0x00
109 #define AK09912_REG_CNTL_MODE_ONCE 0x01
110 #define AK09912_REG_CNTL_MODE_SELF_TEST 0x10
111 #define AK09912_REG_CNTL_MODE_FUSE_ROM 0x1F
112 #define AK09912_REG_CNTL2_MODE_SHIFT 0
113 #define AK09912_REG_CNTL2_MODE_MASK (0x1F << AK09912_REG_CNTL2_MODE_SHIFT)
115 #define AK09912_REG_CNTL3 0x32
117 #define AK09912_REG_TS1 0x33
118 #define AK09912_REG_TS2 0x34
119 #define AK09912_REG_TS3 0x35
120 #define AK09912_REG_I2CDIS 0x36
121 #define AK09912_REG_TS4 0x37
123 #define AK09912_REG_ASAX 0x60
124 #define AK09912_REG_ASAY 0x61
125 #define AK09912_REG_ASAZ 0x62
127 #define AK09912_MAX_REGS AK09912_REG_ASAZ
130 * Miscellaneous values.
132 #define AK8975_MAX_CONVERSION_TIMEOUT 500
133 #define AK8975_CONVERSION_DONE_POLL_TIME 10
134 #define AK8975_DATA_READY_TIMEOUT ((100*HZ)/1000)
137 * Precalculate scale factor (in Gauss units) for each axis and
138 * store in the device data.
140 * This scale factor is axis-dependent, and is derived from 3 calibration
141 * factors ASA(x), ASA(y), and ASA(z).
143 * These ASA values are read from the sensor device at start of day, and
144 * cached in the device context struct.
146 * Adjusting the flux value with the sensitivity adjustment value should be
147 * done via the following formula:
149 * Hadj = H * ( ( ( (ASA-128)*0.5 ) / 128 ) + 1 )
150 * where H is the raw value, ASA is the sensitivity adjustment, and Hadj
151 * is the resultant adjusted value.
153 * We reduce the formula to:
155 * Hadj = H * (ASA + 128) / 256
157 * H is in the range of -4096 to 4095. The magnetometer has a range of
158 * +-1229uT. To go from the raw value to uT is:
160 * HuT = H * 1229/4096, or roughly, 3/10.
162 * Since 1uT = 0.01 gauss, our final scale factor becomes:
164 * Hadj = H * ((ASA + 128) / 256) * 3/10 * 1/100
165 * Hadj = H * ((ASA + 128) * 0.003) / 256
167 * Since ASA doesn't change, we cache the resultant scale factor into the
168 * device context in ak8975_setup().
170 * Given we use IIO_VAL_INT_PLUS_MICRO bit when displaying the scale, we
171 * multiply the stored scale value by 1e6.
173 static long ak8975_raw_to_gauss(u16 data)
175 return (((long)data + 128) * 3000) / 256;
179 * For AK8963 and AK09911, same calculation, but the device is less sensitive:
181 * H is in the range of +-8190. The magnetometer has a range of
182 * +-4912uT. To go from the raw value to uT is:
184 * HuT = H * 4912/8190, or roughly, 6/10, instead of 3/10.
187 static long ak8963_09911_raw_to_gauss(u16 data)
189 return (((long)data + 128) * 6000) / 256;
193 * For AK09912, same calculation, except the device is more sensitive:
195 * H is in the range of -32752 to 32752. The magnetometer has a range of
196 * +-4912uT. To go from the raw value to uT is:
198 * HuT = H * 4912/32752, or roughly, 3/20, instead of 3/10.
200 static long ak09912_raw_to_gauss(u16 data)
202 return (((long)data + 128) * 1500) / 256;
205 /* Compatible Asahi Kasei Compass parts */
206 enum asahi_compass_chipset {
215 enum ak_ctrl_reg_addr {
224 enum ak_ctrl_reg_mask {
241 enum asahi_compass_chipset type;
242 long (*raw_to_gauss)(u16 data);
244 u8 ctrl_regs[REGS_END];
245 u8 ctrl_masks[MASK_END];
246 u8 ctrl_modes[MODE_END];
250 static const struct ak_def ak_def_array[] = {
253 .raw_to_gauss = ak8975_raw_to_gauss,
262 AK8975_REG_ST1_DRDY_MASK,
263 AK8975_REG_ST2_HOFL_MASK,
264 AK8975_REG_ST2_DERR_MASK,
265 AK8975_REG_CNTL_MODE_MASK},
267 AK8975_REG_CNTL_MODE_POWER_DOWN,
268 AK8975_REG_CNTL_MODE_ONCE,
269 AK8975_REG_CNTL_MODE_SELF_TEST,
270 AK8975_REG_CNTL_MODE_FUSE_ROM},
278 .raw_to_gauss = ak8963_09911_raw_to_gauss,
287 AK8975_REG_ST1_DRDY_MASK,
288 AK8975_REG_ST2_HOFL_MASK,
290 AK8975_REG_CNTL_MODE_MASK},
292 AK8975_REG_CNTL_MODE_POWER_DOWN,
293 AK8975_REG_CNTL_MODE_ONCE,
294 AK8975_REG_CNTL_MODE_SELF_TEST,
295 AK8975_REG_CNTL_MODE_FUSE_ROM},
303 .raw_to_gauss = ak8963_09911_raw_to_gauss,
312 AK09912_REG_ST1_DRDY_MASK,
313 AK09912_REG_ST2_HOFL_MASK,
315 AK09912_REG_CNTL2_MODE_MASK},
317 AK09912_REG_CNTL_MODE_POWER_DOWN,
318 AK09912_REG_CNTL_MODE_ONCE,
319 AK09912_REG_CNTL_MODE_SELF_TEST,
320 AK09912_REG_CNTL_MODE_FUSE_ROM},
328 .raw_to_gauss = ak09912_raw_to_gauss,
337 AK09912_REG_ST1_DRDY_MASK,
338 AK09912_REG_ST2_HOFL_MASK,
340 AK09912_REG_CNTL2_MODE_MASK},
342 AK09912_REG_CNTL_MODE_POWER_DOWN,
343 AK09912_REG_CNTL_MODE_ONCE,
344 AK09912_REG_CNTL_MODE_SELF_TEST,
345 AK09912_REG_CNTL_MODE_FUSE_ROM},
353 .raw_to_gauss = ak09912_raw_to_gauss,
362 AK09912_REG_ST1_DRDY_MASK,
363 AK09912_REG_ST2_HOFL_MASK,
365 AK09912_REG_CNTL2_MODE_MASK},
367 AK09912_REG_CNTL_MODE_POWER_DOWN,
368 AK09912_REG_CNTL_MODE_ONCE,
369 AK09912_REG_CNTL_MODE_SELF_TEST,
370 AK09912_REG_CNTL_MODE_FUSE_ROM},
379 * Per-instance context data for the device.
382 struct i2c_client *client;
383 const struct ak_def *def;
386 long raw_to_gauss[3];
387 struct gpio_desc *eoc_gpiod;
388 struct gpio_desc *reset_gpiod;
390 wait_queue_head_t data_ready_queue;
393 struct iio_mount_matrix orientation;
394 struct regulator *vdd;
395 struct regulator *vid;
397 /* Ensure natural alignment of timestamp */
404 /* Enable attached power regulator if any. */
405 static int ak8975_power_on(const struct ak8975_data *data)
409 ret = regulator_enable(data->vdd);
411 dev_warn(&data->client->dev,
412 "Failed to enable specified Vdd supply\n");
415 ret = regulator_enable(data->vid);
417 dev_warn(&data->client->dev,
418 "Failed to enable specified Vid supply\n");
422 gpiod_set_value_cansleep(data->reset_gpiod, 0);
425 * According to the datasheet the power supply rise time is 200us
426 * and the minimum wait time before mode setting is 100us, in
427 * total 300us. Add some margin and say minimum 500us here.
429 usleep_range(500, 1000);
433 /* Disable attached power regulator if any. */
434 static void ak8975_power_off(const struct ak8975_data *data)
436 gpiod_set_value_cansleep(data->reset_gpiod, 1);
438 regulator_disable(data->vid);
439 regulator_disable(data->vdd);
443 * Return 0 if the i2c device is the one we expect.
444 * return a negative error number otherwise
446 static int ak8975_who_i_am(struct i2c_client *client,
447 enum asahi_compass_chipset type)
453 * Signature for each device:
454 * Device | WIA1 | WIA2
455 * AK09916 | DEVICE_ID_| AK09916_DEVICE_ID
456 * AK09912 | DEVICE_ID | AK09912_DEVICE_ID
457 * AK09911 | DEVICE_ID | AK09911_DEVICE_ID
458 * AK8975 | DEVICE_ID | NA
459 * AK8963 | DEVICE_ID | NA
461 ret = i2c_smbus_read_i2c_block_data_or_emulated(
462 client, AK09912_REG_WIA1, 2, wia_val);
464 dev_err(&client->dev, "Error reading WIA\n");
468 if (wia_val[0] != AK8975_DEVICE_ID)
476 if (wia_val[1] == AK09911_DEVICE_ID)
480 if (wia_val[1] == AK09912_DEVICE_ID)
484 if (wia_val[1] == AK09916_DEVICE_ID)
488 dev_err(&client->dev, "Type %d unknown\n", type);
494 * Helper function to write to CNTL register.
496 static int ak8975_set_mode(struct ak8975_data *data, enum ak_ctrl_mode mode)
501 regval = (data->cntl_cache & ~data->def->ctrl_masks[CNTL_MODE]) |
502 data->def->ctrl_modes[mode];
503 ret = i2c_smbus_write_byte_data(data->client,
504 data->def->ctrl_regs[CNTL], regval);
508 data->cntl_cache = regval;
509 /* After mode change wait atleast 100us */
510 usleep_range(100, 500);
516 * Handle data ready irq
518 static irqreturn_t ak8975_irq_handler(int irq, void *data)
520 struct ak8975_data *ak8975 = data;
522 set_bit(0, &ak8975->flags);
523 wake_up(&ak8975->data_ready_queue);
529 * Install data ready interrupt handler
531 static int ak8975_setup_irq(struct ak8975_data *data)
533 struct i2c_client *client = data->client;
537 init_waitqueue_head(&data->data_ready_queue);
538 clear_bit(0, &data->flags);
542 irq = gpiod_to_irq(data->eoc_gpiod);
544 rc = devm_request_irq(&client->dev, irq, ak8975_irq_handler,
545 IRQF_TRIGGER_RISING | IRQF_ONESHOT,
546 dev_name(&client->dev), data);
548 dev_err(&client->dev, "irq %d request failed: %d\n", irq, rc);
559 * Perform some start-of-day setup, including reading the asa calibration
560 * values and caching them.
562 static int ak8975_setup(struct i2c_client *client)
564 struct iio_dev *indio_dev = i2c_get_clientdata(client);
565 struct ak8975_data *data = iio_priv(indio_dev);
568 /* Write the fused rom access mode. */
569 ret = ak8975_set_mode(data, FUSE_ROM);
571 dev_err(&client->dev, "Error in setting fuse access mode\n");
575 /* Get asa data and store in the device data. */
576 ret = i2c_smbus_read_i2c_block_data_or_emulated(
577 client, data->def->ctrl_regs[ASA_BASE],
580 dev_err(&client->dev, "Not able to read asa data\n");
584 /* After reading fuse ROM data set power-down mode */
585 ret = ak8975_set_mode(data, POWER_DOWN);
587 dev_err(&client->dev, "Error in setting power-down mode\n");
591 if (data->eoc_gpiod || client->irq > 0) {
592 ret = ak8975_setup_irq(data);
594 dev_err(&client->dev,
595 "Error setting data ready interrupt\n");
600 data->raw_to_gauss[0] = data->def->raw_to_gauss(data->asa[0]);
601 data->raw_to_gauss[1] = data->def->raw_to_gauss(data->asa[1]);
602 data->raw_to_gauss[2] = data->def->raw_to_gauss(data->asa[2]);
607 static int wait_conversion_complete_gpio(struct ak8975_data *data)
609 struct i2c_client *client = data->client;
610 u32 timeout_ms = AK8975_MAX_CONVERSION_TIMEOUT;
613 /* Wait for the conversion to complete. */
615 msleep(AK8975_CONVERSION_DONE_POLL_TIME);
616 if (gpiod_get_value(data->eoc_gpiod))
618 timeout_ms -= AK8975_CONVERSION_DONE_POLL_TIME;
621 dev_err(&client->dev, "Conversion timeout happened\n");
625 ret = i2c_smbus_read_byte_data(client, data->def->ctrl_regs[ST1]);
627 dev_err(&client->dev, "Error in reading ST1\n");
632 static int wait_conversion_complete_polled(struct ak8975_data *data)
634 struct i2c_client *client = data->client;
636 u32 timeout_ms = AK8975_MAX_CONVERSION_TIMEOUT;
639 /* Wait for the conversion to complete. */
641 msleep(AK8975_CONVERSION_DONE_POLL_TIME);
642 ret = i2c_smbus_read_byte_data(client,
643 data->def->ctrl_regs[ST1]);
645 dev_err(&client->dev, "Error in reading ST1\n");
651 timeout_ms -= AK8975_CONVERSION_DONE_POLL_TIME;
654 dev_err(&client->dev, "Conversion timeout happened\n");
661 /* Returns 0 if the end of conversion interrupt occured or -ETIME otherwise */
662 static int wait_conversion_complete_interrupt(struct ak8975_data *data)
666 ret = wait_event_timeout(data->data_ready_queue,
667 test_bit(0, &data->flags),
668 AK8975_DATA_READY_TIMEOUT);
669 clear_bit(0, &data->flags);
671 return ret > 0 ? 0 : -ETIME;
674 static int ak8975_start_read_axis(struct ak8975_data *data,
675 const struct i2c_client *client)
677 /* Set up the device for taking a sample. */
678 int ret = ak8975_set_mode(data, MODE_ONCE);
681 dev_err(&client->dev, "Error in setting operating mode\n");
685 /* Wait for the conversion to complete. */
687 ret = wait_conversion_complete_interrupt(data);
688 else if (data->eoc_gpiod)
689 ret = wait_conversion_complete_gpio(data);
691 ret = wait_conversion_complete_polled(data);
695 /* This will be executed only for non-interrupt based waiting case */
696 if (ret & data->def->ctrl_masks[ST1_DRDY]) {
697 ret = i2c_smbus_read_byte_data(client,
698 data->def->ctrl_regs[ST2]);
700 dev_err(&client->dev, "Error in reading ST2\n");
703 if (ret & (data->def->ctrl_masks[ST2_DERR] |
704 data->def->ctrl_masks[ST2_HOFL])) {
705 dev_err(&client->dev, "ST2 status error 0x%x\n", ret);
713 /* Retrieve raw flux value for one of the x, y, or z axis. */
714 static int ak8975_read_axis(struct iio_dev *indio_dev, int index, int *val)
716 struct ak8975_data *data = iio_priv(indio_dev);
717 const struct i2c_client *client = data->client;
718 const struct ak_def *def = data->def;
723 pm_runtime_get_sync(&data->client->dev);
725 mutex_lock(&data->lock);
727 ret = ak8975_start_read_axis(data, client);
731 ret = i2c_smbus_read_i2c_block_data_or_emulated(
732 client, def->data_regs[index],
733 sizeof(rval), (u8*)&rval);
737 mutex_unlock(&data->lock);
739 pm_runtime_mark_last_busy(&data->client->dev);
740 pm_runtime_put_autosuspend(&data->client->dev);
742 /* Swap bytes and convert to valid range. */
743 buff = le16_to_cpu(rval);
744 *val = clamp_t(s16, buff, -def->range, def->range);
748 mutex_unlock(&data->lock);
749 dev_err(&client->dev, "Error in reading axis\n");
753 static int ak8975_read_raw(struct iio_dev *indio_dev,
754 struct iio_chan_spec const *chan,
758 struct ak8975_data *data = iio_priv(indio_dev);
761 case IIO_CHAN_INFO_RAW:
762 return ak8975_read_axis(indio_dev, chan->address, val);
763 case IIO_CHAN_INFO_SCALE:
765 *val2 = data->raw_to_gauss[chan->address];
766 return IIO_VAL_INT_PLUS_MICRO;
771 static const struct iio_mount_matrix *
772 ak8975_get_mount_matrix(const struct iio_dev *indio_dev,
773 const struct iio_chan_spec *chan)
775 struct ak8975_data *data = iio_priv(indio_dev);
777 return &data->orientation;
780 static const struct iio_chan_spec_ext_info ak8975_ext_info[] = {
781 IIO_MOUNT_MATRIX(IIO_SHARED_BY_DIR, ak8975_get_mount_matrix),
785 #define AK8975_CHANNEL(axis, index) \
789 .channel2 = IIO_MOD_##axis, \
790 .info_mask_separate = BIT(IIO_CHAN_INFO_RAW) | \
791 BIT(IIO_CHAN_INFO_SCALE), \
793 .scan_index = index, \
798 .endianness = IIO_CPU \
800 .ext_info = ak8975_ext_info, \
803 static const struct iio_chan_spec ak8975_channels[] = {
804 AK8975_CHANNEL(X, 0), AK8975_CHANNEL(Y, 1), AK8975_CHANNEL(Z, 2),
805 IIO_CHAN_SOFT_TIMESTAMP(3),
808 static const unsigned long ak8975_scan_masks[] = { 0x7, 0 };
810 static const struct iio_info ak8975_info = {
811 .read_raw = &ak8975_read_raw,
814 static const struct acpi_device_id ak_acpi_match[] = {
817 {"INVN6500", AK8963},
818 {"AK009911", AK09911},
819 {"AK09911", AK09911},
820 {"AKM9911", AK09911},
821 {"AK09912", AK09912},
824 MODULE_DEVICE_TABLE(acpi, ak_acpi_match);
826 static void ak8975_fill_buffer(struct iio_dev *indio_dev)
828 struct ak8975_data *data = iio_priv(indio_dev);
829 const struct i2c_client *client = data->client;
830 const struct ak_def *def = data->def;
834 mutex_lock(&data->lock);
836 ret = ak8975_start_read_axis(data, client);
841 * For each axis, read the flux value from the appropriate register
842 * (the register is specified in the iio device attributes).
844 ret = i2c_smbus_read_i2c_block_data_or_emulated(client,
851 mutex_unlock(&data->lock);
853 /* Clamp to valid range. */
854 data->scan.channels[0] = clamp_t(s16, le16_to_cpu(fval[0]), -def->range, def->range);
855 data->scan.channels[1] = clamp_t(s16, le16_to_cpu(fval[1]), -def->range, def->range);
856 data->scan.channels[2] = clamp_t(s16, le16_to_cpu(fval[2]), -def->range, def->range);
858 iio_push_to_buffers_with_timestamp(indio_dev, &data->scan,
859 iio_get_time_ns(indio_dev));
864 mutex_unlock(&data->lock);
865 dev_err(&client->dev, "Error in reading axes block\n");
868 static irqreturn_t ak8975_handle_trigger(int irq, void *p)
870 const struct iio_poll_func *pf = p;
871 struct iio_dev *indio_dev = pf->indio_dev;
873 ak8975_fill_buffer(indio_dev);
874 iio_trigger_notify_done(indio_dev->trig);
878 static int ak8975_probe(struct i2c_client *client,
879 const struct i2c_device_id *id)
881 struct ak8975_data *data;
882 struct iio_dev *indio_dev;
883 struct gpio_desc *eoc_gpiod;
884 struct gpio_desc *reset_gpiod;
888 enum asahi_compass_chipset chipset;
889 const char *name = NULL;
892 * Grab and set up the supplied GPIO.
893 * We may not have a GPIO based IRQ to scan, that is fine, we will
896 eoc_gpiod = devm_gpiod_get_optional(&client->dev, NULL, GPIOD_IN);
897 if (IS_ERR(eoc_gpiod))
898 return PTR_ERR(eoc_gpiod);
900 gpiod_set_consumer_name(eoc_gpiod, "ak_8975");
903 * According to AK09911 datasheet, if reset GPIO is provided then
904 * deassert reset on ak8975_power_on() and assert reset on
905 * ak8975_power_off().
907 reset_gpiod = devm_gpiod_get_optional(&client->dev,
908 "reset", GPIOD_OUT_HIGH);
909 if (IS_ERR(reset_gpiod))
910 return PTR_ERR(reset_gpiod);
912 /* Register with IIO */
913 indio_dev = devm_iio_device_alloc(&client->dev, sizeof(*data));
914 if (indio_dev == NULL)
917 data = iio_priv(indio_dev);
918 i2c_set_clientdata(client, indio_dev);
920 data->client = client;
921 data->eoc_gpiod = eoc_gpiod;
922 data->reset_gpiod = reset_gpiod;
925 err = iio_read_mount_matrix(&client->dev, &data->orientation);
929 /* id will be NULL when enumerated via ACPI */
930 match = device_get_match_data(&client->dev);
932 chipset = (enum asahi_compass_chipset)(match);
933 name = dev_name(&client->dev);
935 chipset = (enum asahi_compass_chipset)(id->driver_data);
940 for (i = 0; i < ARRAY_SIZE(ak_def_array); i++)
941 if (ak_def_array[i].type == chipset)
944 if (i == ARRAY_SIZE(ak_def_array)) {
945 dev_err(&client->dev, "AKM device type unsupported: %d\n",
950 data->def = &ak_def_array[i];
952 /* Fetch the regulators */
953 data->vdd = devm_regulator_get(&client->dev, "vdd");
954 if (IS_ERR(data->vdd))
955 return PTR_ERR(data->vdd);
956 data->vid = devm_regulator_get(&client->dev, "vid");
957 if (IS_ERR(data->vid))
958 return PTR_ERR(data->vid);
960 err = ak8975_power_on(data);
964 err = ak8975_who_i_am(client, data->def->type);
966 dev_err(&client->dev, "Unexpected device\n");
969 dev_dbg(&client->dev, "Asahi compass chip %s\n", name);
971 /* Perform some basic start-of-day setup of the device. */
972 err = ak8975_setup(client);
974 dev_err(&client->dev, "%s initialization fails\n", name);
978 mutex_init(&data->lock);
979 indio_dev->channels = ak8975_channels;
980 indio_dev->num_channels = ARRAY_SIZE(ak8975_channels);
981 indio_dev->info = &ak8975_info;
982 indio_dev->available_scan_masks = ak8975_scan_masks;
983 indio_dev->modes = INDIO_DIRECT_MODE;
984 indio_dev->name = name;
986 err = iio_triggered_buffer_setup(indio_dev, NULL, ak8975_handle_trigger,
989 dev_err(&client->dev, "triggered buffer setup failed\n");
993 err = iio_device_register(indio_dev);
995 dev_err(&client->dev, "device register failed\n");
999 /* Enable runtime PM */
1000 pm_runtime_get_noresume(&client->dev);
1001 pm_runtime_set_active(&client->dev);
1002 pm_runtime_enable(&client->dev);
1004 * The device comes online in 500us, so add two orders of magnitude
1005 * of delay before autosuspending: 50 ms.
1007 pm_runtime_set_autosuspend_delay(&client->dev, 50);
1008 pm_runtime_use_autosuspend(&client->dev);
1009 pm_runtime_put(&client->dev);
1014 iio_triggered_buffer_cleanup(indio_dev);
1016 ak8975_power_off(data);
1020 static int ak8975_remove(struct i2c_client *client)
1022 struct iio_dev *indio_dev = i2c_get_clientdata(client);
1023 struct ak8975_data *data = iio_priv(indio_dev);
1025 pm_runtime_get_sync(&client->dev);
1026 pm_runtime_put_noidle(&client->dev);
1027 pm_runtime_disable(&client->dev);
1028 iio_device_unregister(indio_dev);
1029 iio_triggered_buffer_cleanup(indio_dev);
1030 ak8975_set_mode(data, POWER_DOWN);
1031 ak8975_power_off(data);
1037 static int ak8975_runtime_suspend(struct device *dev)
1039 struct i2c_client *client = to_i2c_client(dev);
1040 struct iio_dev *indio_dev = i2c_get_clientdata(client);
1041 struct ak8975_data *data = iio_priv(indio_dev);
1044 /* Set the device in power down if it wasn't already */
1045 ret = ak8975_set_mode(data, POWER_DOWN);
1047 dev_err(&client->dev, "Error in setting power-down mode\n");
1050 /* Next cut the regulators */
1051 ak8975_power_off(data);
1056 static int ak8975_runtime_resume(struct device *dev)
1058 struct i2c_client *client = to_i2c_client(dev);
1059 struct iio_dev *indio_dev = i2c_get_clientdata(client);
1060 struct ak8975_data *data = iio_priv(indio_dev);
1063 /* Take up the regulators */
1064 ak8975_power_on(data);
1066 * We come up in powered down mode, the reading routines will
1067 * put us in the mode to read values later.
1069 ret = ak8975_set_mode(data, POWER_DOWN);
1071 dev_err(&client->dev, "Error in setting power-down mode\n");
1077 #endif /* CONFIG_PM */
1079 static const struct dev_pm_ops ak8975_dev_pm_ops = {
1080 SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
1081 pm_runtime_force_resume)
1082 SET_RUNTIME_PM_OPS(ak8975_runtime_suspend,
1083 ak8975_runtime_resume, NULL)
1086 static const struct i2c_device_id ak8975_id[] = {
1090 {"ak09911", AK09911},
1091 {"ak09912", AK09912},
1092 {"ak09916", AK09916},
1096 MODULE_DEVICE_TABLE(i2c, ak8975_id);
1098 static const struct of_device_id ak8975_of_match[] = {
1099 { .compatible = "asahi-kasei,ak8975", },
1100 { .compatible = "ak8975", },
1101 { .compatible = "asahi-kasei,ak8963", },
1102 { .compatible = "ak8963", },
1103 { .compatible = "asahi-kasei,ak09911", },
1104 { .compatible = "ak09911", },
1105 { .compatible = "asahi-kasei,ak09912", },
1106 { .compatible = "ak09912", },
1107 { .compatible = "asahi-kasei,ak09916", },
1108 { .compatible = "ak09916", },
1111 MODULE_DEVICE_TABLE(of, ak8975_of_match);
1113 static struct i2c_driver ak8975_driver = {
1116 .pm = &ak8975_dev_pm_ops,
1117 .of_match_table = ak8975_of_match,
1118 .acpi_match_table = ak_acpi_match,
1120 .probe = ak8975_probe,
1121 .remove = ak8975_remove,
1122 .id_table = ak8975_id,
1124 module_i2c_driver(ak8975_driver);
1126 MODULE_AUTHOR("Laxman Dewangan <ldewangan@nvidia.com>");
1127 MODULE_DESCRIPTION("AK8975 magnetometer driver");
1128 MODULE_LICENSE("GPL");